Home

2 WIRE INTERCOM SYSTEM

1. Inner Call If multi Monitors are installed in the same apartment select Inner Call all the Intercom 4 Exit OK Select Item Intercom Call lt q Exit Calling p gt Next Page other Monitors will ring at the same time whichever Monitor answers the call conversation is started and the other monitors will stop ringing at the same time note the DIP switches setting of all monitors must be same Direct Dial Guard unit A Monitor can be assigned as Guard Unit Monitor when the Guard Unit Monitor answers the call conversation with the guard person is started 6 Basic Setup Instructions Ring Tone Settings Select User Setup item on main menu page to enter setup page Select Door Station Call Tone Inercom Call Tone or DoorBell Tone item There are 12 pieces ring tones can be selected use w 4 Button to select last next ring tone press MENU button to save and exit Door Station Call Tone set the ring tone calling from outdoor station Intercom Tone set the ring tone calling from other apartments DoorBell tone set the ring tone calling from door bell Door Station Call Tone User Setup 1 Door Station Call Tone Intercom Call Tone DoorBell Tone Clock Next Page gt 4 Exit OK 4 Select Item 7 Date and Time Setting Select User Setup item on main menu page to enter setup page then use A Y button to select Clock item Input date and time by pressing A V Button to increase d
2. Volume items are ring tone and talking volume adjustment 4 Note that all the modifications will be done immediately after the operation Press MENU button to quit the adjust page 12 Specification e Power supply for indoor monitor DC 24V e Power consumption Standby 0 5W Working status 5W e Monitor screen 4 Inch color LCD e Display Resolutions 320 R G B x 240 pixels e Video signal 1Vp p 750 CCIR standard e Wiring 2 wires non polarity e Dimension 199 H x 135 W x 23 D mm XT ENG 25D4 V1 The design and specifications can be changed without notice to the user Right to interpret and copyright of this manual are preserved
3. ENGLISH 2 WIRE INTERCOM SYSTEM USER MANUAL XT ENG 25D4 V1 1 Parts and Functions Main Menu E TALK Button Speaker E 2 Monitor Mounting Microphone LCD Screen Direction Button MENU Button MONITOR Button UNLOCK Button LED Indicator CALL Button 145 160 cm Mounting Hook DIP Switchs Main Connection Terminal Extend Connection Terminal Mounting Hook 1 Use the screws to fix the Mounting Bracket on the mounting box fitting accesories includes a Bracket Two pieces of 4X25 screws are needed for fastening the Mounting Bracket Special 2 wire cables to connect with Monitor 2 Wire the system correctly see the later connection chapter then hang the Monitor on the Mounting Bracket firmly 2 Main Menu Press MENU Button in standby mode the date time page will be showed the date time page will be closed in 1 minute if no operation Press MENU Button again main menu page will be showed 12 20 2010 Mon Main Menu 06 44 im 4 About OK Select Item Basic Door Release Operation Press CALL button on outdoor station the Monitor rings at the same time the screen displays the visitor image Press TALK Button on monitor you can communicate hands f
4. ecrease the value use amp p Button to select last next digital After finish press MENU Button to confirm and return last page 8 Monitor Time settig Select Manual Monitor item on main menu page then select Monitor Time Set item Use A Y Button to increase decrease the value After finish press MENU Button to confirm and return last page 1 Carmen 2 Ding Dong 6 Edelweiss 3 Rain 4 For Alice Selected 06 5 Sonatine 9DoRe Me 10 Happy Birthday 7 Going Home 11 Jingle Bells 8 Congratulation 12 Telephone Ring Cancel H Save amp Exit A Last Next v 2010 12 20 Digital Adjust OK Digital Select Monitor Time Select A Current 01min v Cancel E Save amp Exit 5 Last Next ph 9 Restore to Default Select User Setup item on main menu page to enter setup page then select Next Page item and press MENU button to enter User Setup 2 page select Restore to default item and press MENU button a message will be asked to confirm the restore operation Press Menu button again All settings will be restored to default Note that the restore to default operation will not change the time setting and the datas User Setup 2 Restore to Default Ring Volume Night Ring Volume TPC Configure Are you sure to Restore all to default Restore to default Last Page gt 4 Exit OK 4 Select Item 4 Cancel OK 10 Monitor Installation Setting Main Menu Code Number 0000 Monito
5. r Manual Monitor Intercom User Setup Close Cancel About OK 4 Select Item 1 Press lt button on main 2 Press UNLOCK button and 3 Input 4 digits number menu page to enter about hold for 2 s according to the following information information Use A button to increase decrease the value use 4 button to select the digit Press MENU button to save amp exit How to set the monitor as a Guard Monitor A Monitor can be assigned as Guard Unit Monitor when the Guard Unit Monitor answers the call conversation with the guard person is started The code number of 8004 is used to set the monitor as a guard unit monitor and 8005 is used to cancel this function 6 How to set the monitor panel on In default mode when receive a calling the master and slave monitors will ring at the same time and just the master monitor can display the image while the slave monitors can not But the settings can be changed you can set the master monitor and all the slave monitors to panel on at the same time when receiving a call just input the code number of 8006 on each slave monitor How to set the unlock parameter Unlock mode There are two unlock modes 1 power on to unlock type unlock mode 0 by default 2 power off to unlock unlock mode 1 The code number of 8010 is used to set the unlock mode to 0 The code number of 8011 is used to set the unlock mode to 1 Unlock time The unlock time can be changed by your
6. ree with the visitor for 90 seconds After finishing communication press TALK button again to end the communication If nobody answers the phone the screen will be turned off automatically after 30 seconds During talking state Press UNLOCK Button to open the door for the visitor When the monitor is in standby mode press MONITOR Button or select Monitor item on main menu page The screen can display the view of outside If multi door stations are installed select Manual Monitor item to enter camera switch mode Select Camera 1 item the screen will display the image from the first door camera Similarly Select Camera 2 item to choose the second one Select Camera 3 item to choose the third one Select Camera 4 item to choose the fourth one Press MONITOR button again to end monitoring 5 Intercom Function When the monitor is in standby mode press CALL Button to enter Intercom Function page or select Intercom item on main menu page Use A VW Button to move upward downward to select the item you want press MENU Button to enter 1 Intercom Call User in one apartment can call other apartments in the system the namelist will be created automatically by the system Selete a name on the screen then press MENU button or CALL Button to dial Note 1 Press MENU or CALL button again to redial 2 Press TALK button to cancel the call 3 The DIP switches code of each monitor must set different
7. sed to set the time format as 12 hour system The code number of 8013 is used to set the time format as 24 hour system How to set the menu language The monitor can support multi languages and it is so simple and fast just input the corresponding language code on monitor The language code number are as follows 8101 English 8107 Portuguese 8102 French 8108 S Chinese 8103 Spanish 8109 T Chinese 8113 Russian 8114 Slovakia 8104 Italian 8110 Greek 8115 Hungray 8105 German 8111 Turkish 8116 Czech 8106 Dutch 8112 Polish Note the monitor can only support 4 types of languages English French Spanish and German are default But you can customize any 4 languages by yourself The language which is unavailable will be set to English in default a 11 Screen and Volume Adjustment During monitoring or talking press MENU Button the ADJUST MENU will be displayed Use A Y Button to select the adjustment item use gt Button to decrease increase the value 1 The first item is Scene mode selection Total 4 screen modes can be selected in sequence ES Brightly Normal User Soft and Bright Whenever you Bright modify Brightness or colour Scene item will be Color set to User mode automatically ka Be elect Camera 2 The Brightness and Colour item is for the image quality setting adjust the value to get the best image you like 4 Select Item Exit lt gt Dec Inc 3 The Ring Volume and Talk
8. self at any time it can be set from 1 to 9 seconds The code number from 8021 to 8029 are used to set the unlock time to 1 9 seconds 2 locks control The monitor can be set to control 2 locks while you should set the unlock2 item to on state The code number of 8015 is used to set the unlock2 off that 1t can only control one lock The code number of 8014 is used to set the unlock2 on that 1t can control two locks Note 1 During talking or monitoring state UNLOCK button two unlock icons will be showed Use A V button to select the item you want and press UNLOCK or MENU button to release the corresponding door select J item to exit 2 Restore to default operation will not chang the parameters setting 7 How to set the slave monitor address Maximum 4 monitors can be connected in one apartment one master monitor together with 3 slave monitors so you should set the address correctly note must have one monitor to be set as master monitor The code of 8000 is used to set the master monitor The code of 8001 is used to set the first slave monitor The code of 8002 is used to set the second slave monitor The code of 8003 is used to set the third slave monitor How to set date and time format The system offers two methods of date and time The code number of 8008 is used to set the date format as month date year The code number of 8009 is used to set the date format as date month year The code number of 8012 is u

2 WIRE INTERCOM SYSTEM

Contents

Download Pdf Manuals

Related Search

Related Contents