2.4GHz Digital Wireless Rearview Camera with 7
Contents
1. USER MANUAL Model VTC700R Packing List TFT LCD Monitor Video Cable Antenna for Camera and Monitor Stamping Mount Monitor Power Supply Screw Holder Cable 2 4GHz Digital Wireless Rearview Camera with 7 Color LCD Monitor Suc Holder FOREWORD In Line Wire Cigarette Lighter Grommet Congratulation The Rearview Camera when used as Connectors Adapter described will give you years of dependable service in you r Car ELUCK RV or mini van We have taken numerous The picture are for reference only please refer to real subjects measures in quality control to ensure that your product arrives in top condition and will perform to your satisfaction Model VTC700R STRUCTURE IE LEDS Leng Bracket _ BAncenna LCD Screen Pairing Power On Off Mirror Brightness Contrast Power Indicator Power Socket Video Output INSTALLATION These installation instructions do not apply to all vehicles They are meant as only a general guide to big vehicle makes amp models For specific questions contact your vehicle manufacturer Consult your local motor vehicle laws on the use of this product Do not attempt this 1f you are not knowledgeable with electrical installation practices CAMERA INSTALLATION 2 Drill six holes one hole for the camera s power wire and five holes for installation of the camera 1 You may mount the camera near the top of the license plate w2. on the LCD is unclear adjust the contrast brightness and mirror by toggling the buttons on the monitor o Contrast Control the 5 levels of LCD contrast can be adjusted by pressing the CONTRAST DUCLON o Brightness Control the 5 levels of LCD brightness can be adjusted by pressing the BRIGHTNESS button o There are four different views for the monitor If the image is not oriented correctly press the MIRROR button on the monitor to change the orientation until it is correct F E gt Normal Mirror Upside Down J Normal Upside Down Mirror o These different views allow you to mount the camera and or monitor with either right side up or upside down and still display the image correctly on the monitor The image displayed should match your rear view mirror After testing the unit fully tighten the Camera DOCS Notice Press the CONTRAST button for 4 seconds to reset the display to the factory default The VTC700R Monitor has a video output that can be used to display the Camera input on a larger monitor or TV screen Connect the included RCA cable to the monitor and the other end into the AV input of the larger monitor or IV When the connection 1s successful the following message will display on the monitor Switching to NTSC TV system If the image does not display on TV check the video cable and make sure it is fully inserted into the monitor gt Q gt w m z AM lt mMaAMmMA SP
3. ECIFICATION Items Value Imaging Sensor CMOS TA Night Range Consumption Current Max 150mA IR OFF amp 230mA IR ON Dimensions W x D x H 96x52x61 mm Excluding Bracket Transmission Frequency ISM 2 400 2 483MHz Power supply Voltage Unobstructed Effective Range e The actual transmission range may vary according to the weather location interference and building COnstrucreson All the specifications are subject to minor change without prior notice ECC INFORMATION This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CAUTIONS The apparatus shall not be exposed to dripping or splashing and no objects filled with liguids such as vases shall be placed on the apparatus Turn off the camera receiver if the system is not in use The Camera receiver can only be completely disconnected form the mains by unplugging the adapter Do not cut the DC power cable of the apparatus to fit with another power source Attention should be drawn to the environment aspects of battery disposal EU ENVIRONMENTAL PROTECTION Waste electrical products shoul
4. d not be disposed of with household waste Please recycle where facilities exist Check with your local authority or retailer for recycling advice This manual has been updated by RoadTrucker Inc
5. ith screws Install the camera with five screws supplied and adjust the camera to a proper angle 3 Insert the power 4 wlre of the camera into the supplied grommet and then pass the power wire into the vehicle Notice The product is not sultable for mini vehicles For specific vehicle such as container car or container truck please consult your local vehicle garage for installation Some vehicle may have a hole available to pass the wire through so you do not need to drill a hole Before drilling those holes you must check and make Sure no other components are in the way Before drilling we strongly recommend you check carefully for any possible interference to avoid unexpected damages CAMERA POWER WIRE CONNECTION Camera s power cable Insert the Insert the wire Crimp tap and to be attached then close lock 1 Once you have located the reverse light circuit you da e N Se need to route the power wire to that location You must securely fasten the power wlre to prevent it from being caught on a vehicle component such as the trunk hinge Never route the cable outslde the vehicle 3 Wrap In Line wlre connectors over the camera power wire reverse lam 2 The camera is equipped with Reverse Voltage Protection Please make sure that the RED wire is connected to positive and the Black wire is connected to negative Test by having someone place the vehicle in Reverse The co
6. rrect wires will have a 12 Volt DC potential only when the vehicle is in Reverse Monitor Installation b Use the cigarette lighter adapter to connect the power socket of the monitor into the 12 Volt socket of the vehicle 1 Fastening the 2 Peel off the Suction cup holder backing paper of the to the back of the suction holder and MOniL Or press it on the front window of the vehicle 4 Power on and the power indicator lights blue Adjust brightness contrast and orientation of image on the monitor THE WHOLE DIAGRAM OF INSTALLATION POSITION 3 Connect power to the monitor There are two methods as below a Wire directly to the vehicle fuse box paying attention to the positive and negative polarity OPERATIONS 1 Press the POWER button on the monitor for 3 seconds the power indicator will illuminate 2 This equipment has been paired successfully from the factory If there 1s no display image you will need to palr agaln Pairing Method On the back of the Camera there are 2 threaded holes with a button screw in the lower hole Unscrew the metal button in the lower hole and screw it into the upper hole Then on the front of the monitor press and hold the PAIRING button for 3s to pair the frequency signal in 30 seconds If pairing is SUCCeESSIUL remove the button Screw Erom The Lop hole in the Camera and screw it back into the bottom hole After paired and using r 3 If the image
Download Pdf Manuals
Related Search
2.4GHz Digital Wireless Rearview Camera with 7