stringultra t-800 stringing machine user`s manual anatomy
Contents
1. A STRINGULTRA 800 STRINGING MACHINE USER S MANUAL ANATOMY The T 800 is shipped to you in three cartons Here is what the three cartons contain 1 Electronic Tension Head 2 Racquet Mount 3 Floor Stand Side Support Rubber Cover Side Support Arm Adjustment Knob Brake String Clamp Holder Turntable Tensioning Button Lower Housing Mounting Stock Adjustment Knob Racquet Holder Base Feet Side Support Arm Center Support Adjustment Knob Mounting Stock Center Support String Clamp String Gripper Diablo Upper Housing Control Panel String Reel Holder Column ASSEMBLY 1 2 Insert base feet lower column Place the column stand up side down on the NOTE Set the cable of the electric feet in the front at the same direction as the floor curved shape side of the feet 3 Array 8 studs of the lower column to match 4 Insert the nuts onto 8 studs and tighten them the circular holes of the base feet by a 12 mm wrench 7 Mount racquet holder rear of 8 Tighten screw of racquet holder into column column by a 6 mm wrench 9 To complete the floor stand screw the string 10 Tilt the electronic tension head and remove reel holder into the front of the column the four washers and nuts from the metal bottom base of the electronic tension head 11 Place the el2. ectronic tension head over the Plug the power cord of the floor stand anchor of the floor stand and align the 4 studs into the outlet located beneath the metal under the bottom base of machine with the electronic the tension head corresponding l 2 next to holes in the 1 height anchor plate adjustment and button re position the four washers and nuts onto the anchor tightening them by a 12 mm wrench 13 Push the brake backward to left side to unlock the brake and then insert the entry part of the turntable into the hole of the tension head s lower housing 15 Select the suitable side supports and insert them on the side support arms For tennis racquet frames please choose V support and for the badminton racquet frame please use L support tennis badminton 17 For mounting the oversized tennis racquet frame please use the extended adaptor at the center support 14 Insert the string clamps 16 For mounting the badminton racquet frame please use the special center support marked with BADMINTON 18 The machine is now fully assembled and can be plugged into a 220 Volt outlet 19 Secure drawer optional beneath lower housing of machine with screws mm wrench KEYPAD OPERATING INSTRUCTIONS ICEF 7 800 keypad is protected by plastic film that should be remov
3. ed before using MEMORY Indexes from 8 preset tension settings that can be stored in memory To store your desired tension please hold MEMORY key down for 2 seconds until a beep sound is alarmed KG LB Selects tension scale Each press of the KG LB key toggles between KG and LB KNOT Increases pulling tension by 10 over the selected tension for one pull The screen will display 59 to indicate the KNOT function is set It can be added more max 20 by pressing UP button manually or reduced to less min 0 by pressing DOWN button manually Yet as long as the tension 15 switched to a different tension or the machine is switched off and on again or the knot function will revert to its default 10 setting automatically SPEED Changes pulling speed of string gripper from Slow to Fast Cycles between six speed selections Timer Function original factory setting 1 To start timer press TIMER key 2 To stop it press TIMER key once more 3 To reset TIMER hold TIMER key down for 2 seconds Countdown Function 1 Hold KNOT key while turning the machine on 2 Press PRE STRETCH key several times until the TIMER is shown on the screen 3 Press TENSION key to motivate TIMER OFF TIMER ON is for the function of the timer TENSION key here is to change TIMER from ON to OFF or OFF to ON Each press of the TENSION key toggles between ON and OFF 4 Press MEMORY key to store your selectio
4. in the opening between the jaws of the string gripper Tensioning is activated by pushing the handy tensioning button behind the string gripper or the triple touch sensor Pressing the touch sensor N TE please touck_three strips together or handy tensioning button or again causes the string gripper rem dase the string HEIGHT ADJUSTMENT Loosen the locking knob on the column before making height adjustment Press the height adjustment button under the metal bottom base of the electronic tension head until the desired height is attained available height adjustable range 30 cm Tighten the locking knob onto the column to avoid the machine body rocking during stringing amp fuse is located inside of the electronic tensioner It is used for the floor stand 1 MOUNTING THE RACQUET FRAME Place the racquet frame properly on the top of both mounting stocks Adjust the distance between the mounting stocks to accommodate the size of the racquet frame by pulling out the mounting stock adjustment knob out and rotating it clockwise to spread the distance between two mounting system 10 2 Lightly tighten center supports by turning center support adjustment knob clockwise ATTENTION Don t over tighten the knob of the center support first 3 The side supports are adjustable to provide support to the racquet frame Open side support arms by turning side support arm adjustment knob coun
5. n 5 Hold TIMER button for 2 seconds until the block becomes white instead of black block EERE ono lies 6 Enter your desired time by pressing UP or DOWN keys 7 Press TIMER two times to motivate countdown function after the desired time 15 set 8 After the desired time is attained the machine will alarm by two beep sounds 9 Press TIMER to stop beep sound PRE STRETCH Cycles b n 0 5 10 15 and 20 When stretching the tensioner exceeds selected tension then rolls back to it Stretching enhances tension stability but be careful not to exceed the string tensile strength or it will break TENSION Programmed preset tensions cycle between 15 30 45 amp 60 LB or between 6 5 13 5 20 5 amp 27 5 KG UP DOWN Changes tension setting in 1 0 or 0 1 Lb or Kg increments Holding the UP DOWN key down for a second will accelerate the process of tension increments in 1 0 Lb or Kg instead of 0 1 Lb or Kg POWERING The main power switch is located on the right of the machine next to the receptacle for the power cord A2 amp fuse is located in the power cord receptacle Voltage between 220V and 240V 50 Hz to 60 Hz is acceptable A grounded outlet must be used Note If you need to use this machine with 110V call the agent Computerized Stringing Machine INPUT 100 120 50HZ 60HZ FUSE 2 TENSIONING Rotate the string around the Diablo and insert the string
6. n is not correct you can use a precision electric calibrator optional to calibrate your machine below 1 Hold KNOT key while turning the machine on 3 Use a tension calibrator Use a tennis string clamp to secure the tennis string on one end of the tension calibrator and place the string that is attached to the other end of the tension calibrator into the string gripper 16 4 Machine will provide you 8 tensions for calibration 5 kgs 11 Ibs 10 kgs 22 lbs 15 kgs 33 Ibs 20 kgs 44 lbs 24 9 kgs 55 Ibs 29 9 kgs 66 Ibs 39 9 kgs 77 Ibs and 44 kgs 88 Ibs P S You may press the SPEED key to see the different calibration tensions appearing to the display 5 Pull the string by pressing the handy tensioning button or touch sensor 6 Check the measurement of the calibrator 7 If the measurement of the calibrator is different from the tension displayed on the screen of the machine please press up or down arrow key to decrease or increase the measurement of the calibrator 17 8 Release string by pressing handy tensioning button or touch sensor 10 Finishing 8 times of tension calibration or even more times until the measurement of the calibrator is identical to the tension shown on screen of the machine and then release the string 11 Press SPEED key two times and then press MEMORY key two times as well so as to store what you have calibrated 18
7. terclockwise After the side support arms hold the racquet frames go back to step 2 tightening the center supports 11 SWIVEL CLAMP OPERATION Different strings and different gauges require different adjustments Adjustment can usually be done by finger tips Note that the handle of the swivel clamp should be lifted before adjustment SWIVEL CLAMP BASE OPERATION The lever on the swivel clamp base is turned clockwise to lock the base To unlock the lever is turned counterclockwise If the swivel clamp base doesn t lock well to the turntable or the locking angle of the lever of the clamp base is too big you may adjust the nut beneath the clamp base by a 17 mm wrench clockwise or counterclockwise Closed Position Open Position 12 HOLE FINDER OPERATION Use a hole finder to create a pathway between or around strings and through tight grommets Insert the awl through the grommet hole and pull the handle of the awl outward leaving the outer sheath in the grommet hole Insert the end of the string into the sheath 13 FLAT NOSE PLIERS OPERATION TENNIS AWL OPERATION DIAGONAL CUTTER PLIERS OPERATION 14 GROMMET REMOVER OPERATION The grommet remover works like an awl by twisting you can grind the broken tubing out of the racket 15 TENSION CALIBRATION Your machine has been well calibrated at the factory so it is not necessary to calibrate your machine If you have reason to suspect that tensio
Download Pdf Manuals
Related Search
stringultra t 800 stringing machine user`s manual anatomy