Full-Motion TV Mount - 47 to 90 Installation Guide
Contents
1. November 2013 Copyright 2013 by SHG Inc All rights reserved2. U S at no cost to the customer About SIIG Inc Founded in 1985 SIIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG continues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio All centered around the distribution and switching of A V signals over CAT5 6 these products include matrix switches distribution amplifiers extenders converters splitters cabling and more SIIG is the premier one stop source of upgrades and is committed to providing high quality products while keeping economical and competitive prices High quality control standards are evident by one of the lowest defective return rates in the industry Our products offer comprehensive user manuals user friendly features and most products are backed by a lifetime warranty SIIG products can be found in many computer retail stores mail order catalogs and e commerce sites in the Americas as well as through major distributors system integrators and VARs PRODUCT NAME Full Motion TV Mount 47 to 90 Full Motion TV Mount 47 to 90 is a trademark of SUG Inc SUG and the SHUG logo are registered trademarks of SHG Inc Allothernames used in this publication are for identification only and may be trademarks of their respective owners
3. wall and line up the mounting slots with the drilled holes Check the bubble level to verify that the wall plate is level For each location insert a lag bolt t and washer u into the wall See Figure 2 8 Tighten the bolt with an open ended or socket wrench by turning clockwise until tight E E Figure 1 U Finder Figure 2 CAUTION Do not over tighten the bolts doing so may cause unnecessary damage to the wall CAUTION Do not release the wall plate until it is properly mounted and secured to the wall 4 B Concrete Brick Wall Installation Note The concrete anchors must be used for concrete and brick installation 1 With the help of an assistant place the wall plate onto the wall in the desired mounting location and check the integrated bubble level to ensure it is level Mark six holes minimum of 6 inches apart to be used for securing the mount and place the wall plate aside Locate the holes directly into the concrete or brick never into the mortar between the blocks See Figure 3 Drill six holes using an electric drill and 3 8 masonry drill bit to a depth of 3 at the positions you marked Insert a concrete anchor v into each hole If necessary a hammer can be used to lightly tap each concrete anchor into place so that they are flush with the wall Once all of the concrete anchors are in place move the wall plate back into position Check the bubble level to verify that the wall pla
4. fic legal rights and you may also have other rights which vary from state to state Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A Ifitis within the store s return policy period please return the product to the store where you purchased it B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then Request A Product Replacement to submit a request to SIIG RMA or fax a request to 510 657 5962 Your RMA request will be processed if the product is determined to be defective an RMA number will be issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e You are responsible for the cost of shipping to SIG Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the
5. nting surface Do not install near heater fireplace air conditioning in direct sunlight or any other heat producing source Failure to do so may result in damage to the display and could increase the risk of fire Make sure no water or natural gas lines are present where the mount is to be installed Cutting or drilling into water or natural gas lines could cause personal injury or property damage Proper installation procedure by yourself or a qualified service technician as outlined in the installation guide must be adhered to Failure to do so could result in serious personal injury When mounting to a wall that contains wood studs confirm the dead center of the wood stud prior to installation it is recommended that the wood studs be a minimum of 16 apart if applicable This product is intended for indoor installation use only Premature product failure or serious personal injury could occur if this product is used outdoors It is recommended that two people perform the installation Injury and or damage can result from dropping or mishandling the display Tools Required Electronic stud finder for drywall installation Phillips head screwdriver and bubble level Socket or wrench set metric Electric drill 5 32 drill bit for wood stud installation 3 8 masonry drill bit for concrete brick wall installation Important The Full Motion TV Mount 47 to 90 is shipped with the proper installation hardware and parts Make
6. sure that none of the items are missing or damaged before starting the installation If there are any missing and or damaged parts please stop the installation and contact your place of purchase Hardware Kit x1 Wall plate x1 Left monitor bracket x1 Right monitor bracket d e f x4 M4x12 bolt x4 M5x12 bolt x4 M6x12 bolt x4 M8x16 bolt h x4 M4x30 bolt x4 M5x30 bolt x4 M6x35 bolt x4 M8x40 bolt l m n O O G 10 x4 M4 lock washer x4 M5 lock washer x4 M6 lock washer x4 M8 lock washer p gt Q x4 M4 M5 spacer x4 M6 M8 spacer x8 M4 M5 washer x4 M6 M8 washer t u V z x6 Lag Bolt x6 Lag bolt washer x6 Concrete anchor Step 1 Wall Plate Installation A Wood Stud Installation 16 on center 1 Use a high quality electronic stud finder commercially available to locate dead center of two wood studs 16 apart and mark the location with a pencil See Figure 1 2 With the help of an assistant place the wall plate onto the wall in the desired mounting location and check the integrated bubble level to ensure it is level 3 Mark the right upper and lower and the left upper and lower positions of the small horizontal slots that are in alignment with the wood studs You should mark four positions total Take down the wall plate Next pre drill a 5 32 hole to a depth of 3 in the wood stud at each marked location 6 Place the wall plate against the
7. t the bolt h i j k with the correct depth and diameter of the mounting holes of your TV Please make sure the monitor brackets b c are vertically centered and level with each other Thread the bolts into the TV using the correct lock washer l m n o washer r s and spacer p q For the M4x30 Bolt h and M5x30 Bolt i you will need another washer r between the monitor bracket and the spacer See Figure 5 M4 Diameter Bolt M6 Diameter Bolt Curved Back Television Figure 5 Step 3 Attaching the TV to the Wall Plate Warning Some TVs may require two people to lift and position it onto the wall plate SIIG Inc is NOT RESPONSIBLE for any damage or injury caused by incorrect installation assembly or use 1 Hang the TV with monitor bracket b c assembly onto the top of the wall plate a then let the bottom of the monitor brackets rotate to the bottom of the wall plate See Figure 6 2 Usea screw driver to tighten the safety bolt on each monitor bracket b c to secure the TV to the wall plate a See Figure 7 Figure 6 Figure 7 Step 4 Cable Management 1 Secure the cables from your TV Monitor through the cable management loops See Figure 8 Figure 8 Step 5 Tilt Adjustment 1 Loosen the tilt adjustment levers on each side tilt the TV to the optimal viewing angle then tighten the levers to secure the tilt angle Note The tilt adjustment levers are designed with ratchet mechanism To adj
8. te is level Insert lag bolts t and washers u into the concrete anchors as shown and tighten Do not fully tighten until all bolts are in place See Figure 3 Figure 3 CAUTION Do not over tighten the bolts doing so may cause unnecessary damage to the wall CAUTION Do not release the wall plate until it is properly mounted and secured to the wall 5 Step 2 Mounting the Monitor Brackets The hardware kitincludes bolts of various diameters and lengths to ensure optimal installation Step 2A Mounting the Monitor Bracket to a TV with a Flat Back 1 Place your TV screen down on a soft flat surface and locate the threaded mounting holes that are located on the back of the display 2 Determine the depth of the mounting holes by inserting a straw or toothpick Select the bolt d e f g with the correct depth and diameter of the mounting holes of your TV 3 Please make sure the monitor brackets b c are vertically centered and level with each other 4 Thread the bolts into the TV using the correct lock washer l m n o and washer r s See Figure 4 M4 Diameter Bolt M6 Diameter Bolt Flat Back Television Figure 4 Step 2B Mounting the Monitor Bracket to a TV with a Curved Back 1 2 Place your TV screen down on a soft flat surface and locate the threaded mounting holes that are located on the back of the display Determine the depth of the mounting holes by inserting a straw or toothpick Selec
9. ust the lever s position pull it out and rotate left or right release the lever and rotate to loosen or tighten Repeat several times if needed See Figure 9 Figure 9 Step 6 Leveling the TV If needed the mount can be re leveled after it has been mounted to the wall by rotating the front plate that the TV mounts onto To make this adjustment loosen the three bolts located on the back of the front plate hold the TV and carefully rotate to the left or right until itis level Retighten the three bolts See Figure 10 Figure 10 Maintenance Check the mounting screws every two months for tightness 10 Blank Page Technical Support and Warranty QUESTIONS SIIG s Online Supporthas answers Simply visit our web site at www stig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analysts will promptly respond SIIG offers a 5 year manufacturer warranty with this product This warranty covers the original purchaser and guarantees the product to be free of any defects in materials or workmanship for five 5 years from the date of purchase of the product SIIG will at our discretion repair or replace with an identical product or product having similar features and functionality the productif defective in materials or workmanship This warranty gives youspeci
10. w Full Motion TV Mount 47 to 90 Installation Guide Full motion Articulating LCD Plasma TV Wall mount TV size 47 90 Tilt angle 12 degrees Max load capacity 200 lbs 90 kg Wall distance at the front plate 3 9 to 19 7 Important If you have difficulty following or understanding these installation instructions please consult a qualified installation specialist 04 0923A 1 Caution Prior to installation of this product the installation guide should be read and completely understood The installation guide must be read to prevent personal injury and property damage Keep the installation guide in an easily accessible location for future reference This mount contains small parts which can act as a choking hazard if swallowed CAUTION The maximum load capacity is 200 lbs Use with products exceeding the maximum load capacity may cause serious injury See apparatus instructions The wall structure must be capable of supporting at least five 5 times the maximum load capacity as indicated If not the wall must be reinforced Recommended mounting surfaces wood stud and solid flat concrete If the mount is to be installed on any surface other than wood studs or solid concrete use suitable hardware not included but commercially available Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the display and or damage to the mou
Download Pdf Manuals
Related Search
Full Motion TV Mount 47 to 90 Installation Guide