2008-14 Mitsubishi Evolution / Type33F
Contents
1. Lefer INTERCOOLER KIT Mitsubishi Evolution X CZ4A 4B11 MIVEC TYPE 3 F Instruction Manual e Please read this entire manual before installation e Keep this manual for future reference Model Chassis Code EVO X CBA CZAA 4B11 MIVEC 07 10 Spec O Compatible with OEM or GReddy Piping O Compatible with the GReddy Oil Cooler O Compatible with the GReddy SST Oil Cooler O Modifications to the Hood Catch Support amp Air Duct are required AN Do not use on any vehicle other than what is described above 1 Parts List Bu 1 Intercooler TYPES SET BE 2 Silicone Hose 60 070 Reue 0000 nnd 3 Hose Clamp AO O FESO ie 2 1 f aa JO O O 2 a 9 Intercooler Bracket RH a al A f e v L r IIIa __ Sponge lape t IO dc U l e 8 M6x20mm P 1 0 A a _ 9 M6 PTO AN ja Z 10 M8 X 15mm P 1 25 B S W 2 Parts List Diagram 2 Removal of Stock Parts 2 2 2 3 2 4 2 5 Refer to the factory service manual for removal of stock parts Disconnect the negative terminal of the battery Remove the front under cover and front bumper Remove the intercooler inlet amp outlet pipes Remove the intercooler assembly X The OEM intercooler hanger bracket will be reused Remove the harness clips then uninstall the front bumper reinforcement 3 Kit Installation 3 1 Modification of OEM Parts 1 Cut the outlined portion of the hood catch support bracket to clear the Intercooler Be sure to2. inforcement x gt 3 3 Intercooler Piping Installation 1 Attach the OEM piping to the Intercooler Inlet side using part s 2 3 amp 4 as shown in the picture to the right 2 Attach the Intercooler Outlet side to the OEM piping using part s 2 3 amp 4 as shown in the picture to the right 3 4 Starting of the Engine 1 Attach the negative cable to the negative terminal of the battery 2 Inspect the newly installed intercooler for air leaks or strange noises 3 5 Front Bumper Installation 1 You will need to trim the both sides of the interior air dams approximately 5mm trim the area marked in white directed with arrows 2 Make sure you have trimmed enough material so that there is no interference with the new Intercooler then install the front bumper 3 Install the front under cover This Concludes the Installation of the Intercooler Kit
3. wear safety glasses lenses when cutting the support bracket Exposed metal can and will rust we recommend protecting the surface with paint 3 Reinstall the front bumper reinforcement in its original location 3 2 Intercooler Installation 1 Remove the two bolts from the front end cross member 2 Affix the supplied sponge tape to the welds of intercooler end tanks x Be sure to clean the intercooler surface of any debris or oils for a proper bond with the sponge tape 3 Install the brackets as show below using the M8 x 15mm bolts amp washers M8 x 15 4 Mount the intercooler to the cross member via welded brackets X lt Use the supplied M6 x 20mm bolts The driver side will also use the M6 x 20mm bolts utilizing the service holes x If the horn interferes with the placement of the intercooler loosen the horn bolt and situate the horn er away from the intercooler A rz e il A M6 x 20 M6 x 20 ce T FT oOo EG x Using the OEM bolts install the new intercooler brackets in between the bumper reinforcement amp OEM intercooler bracket as shown in the picture amp diagram below Y A GReddy Intercooler A Bracket F aS i Intercooler A s L OEM Intercooler OEM Bolts FM em E I racket N I lt yy OEM Intercooler Y y 3 Y gt j i Bracket 5 Once you have adjusted the position of the new intercooler tighten the bolts securely y K O Re
Download Pdf Manuals
Related Search
2008 14 Mitsubishi Evolution / Type33F mitsubishi evolution final edition