Home

INSTALLATION AND SERVICE PROGRAMMING

Contents

1. Visible and programmable only with Operating mode MDB Some of these menus are only visible if a peripheral device is connected that foresees their use Rev M 01 Pagina A 10 d am ia n Serie EUR7 rheavendors O gt MAXIMUM CREDIT To set the maximum credit value accepted by the MDB payment system When the credit in the vending machine reaches this value the machine no longer accepts coins or banknotes Settable values 0 65535 independent of the position of the comma e g with 2 decimals the maximum credit is 655 35 If set to 0 this control is disabled Default 0 Programming lt a Maximum credit gt COIN RETURN PARAMETERS If there is an MDB coin return payment system installed in the vending machine selecting this function it will be possible to set the following operating parameters for it COIN MINIMUM TO INDICATE NO CHANGE AVAILABLE Visible and programmable only if MDB coin return payment system installed To set the minimum value of the coins that must be present in each individual tube of the MDB coin box below which the vending machine indicates no change available Settable values 0 15 MDB oe 7 aS O EA MinTube NoChange Current value COIN MINIMUM IN TUBES TO GIVE CHANGE Visible and programmable only if MDB coin return payment system installed To set the minimum value of the coins that must be present in the tubes in an MDB payment system below whic
2. You are trying to make the sliding panel 10 work but the motor 11 idles or is blocked Check that the sliding panel 10 can slide freely that the guides are clean and that there is nothing preventing complete closing Check that the motor gear 11 works correctly Check the operation of the opening microswitch 13 and the relative wiring Replace it if necessary OFF L13k Levers not down Error movement locking lever product removal door OFF L131 During a cycle of opening closing of the sliding panel 10 is not detected lowering of the locking levers 5 of the door product Check that the two lock levers 5 of the door product can move freely Check that the two microswitches 6 of lock levers are correctly connected and adjusted make sure that the wiring is in good condition and replace them if necessary Rev M 01 Page 11 d am ia n Serie EUR7 rheavendors O Message bode Message text Problem description solution OFF L20 CL1 CPU 2 circuit board errors These error messages concern failures of the vending machine s circuit board OFF L20a CL1 CPU Error Restart Change CPU card error OFF L20b Turn the vending machine off and then on again if the problem persists replace the CPU card 2 OFF L20f CL1 CPU SW Error Reinstall SoftW CPU card software error OFF L20g Turn the vending machine off and then on again if the
3. SAFETY TEMPERATURE Visible and programmable only with Refrigerator operation Food amp Snack To read the safety temperature for the sale of food products see the Overtemperature control section and the description of the ERR L09 error message for the description Rev M 01 Pagina A 14 d am ia n Serie EUR7 rheavendors O Settable values 0 45 C To deactivate this function set it to 240 C Programming Refrig P y E p SrtA SAANA Security temper Current value gt OVERTEMPERATURE TIME Visible and programmable only with Refrigerator operation Food amp Snack To set the time beyond which the internal temperature must not exceed the safety temperature see the Overtemperature control section and the description of the ERR L09 message for the description Settable values 0 1440 minutes Default 45 C Programming i Refrig Param s Overtemper tim Current value gt RESTOCKING TIME Visible and programmable only with Refrigerator operation Food amp Snack To set the time that is added to the overtemperature time each time restocking takes place vending machine turned on see the Overtemperature control section for the description Settable values 0 1000 minutes Default 30 minutes Programming Default 120 minutes Refrig P On Serg aaRS Refueling time Current value gt CONNECTED PROBES To read the number of refr
4. make sure that the package is whole and that the products are in a good state of preservation in conformity with the current applicable regulations concerning the preservation of sold products The sale of toxic products e g detergents with food products is not allowed in the same vending machine The vending machine may not be used to sell explosive material or material at risk of fire Rev M 01 Page 2 damian rheavendors O Serie EUR7 These models are manufactured in variations A without refrigeration unit R with Standard refrigeration unit S with Super refrigeration unit and L with Super L refrigeration unit with the characteristics shown in the following table Characteristics Variation EUR7B x xx A EUR7B x xx R EUR7P x xx S EUR7L x xx L Power supply Voltage 220 230V Frequency 50Hz Rated power 160 W 460 W 490 W 490 W Max Rated power 260 W 620 W 650 W 650 W Protection IP24 Only suitable for covered and protected places where it cannot be rained on or sprinkled by water jets Refrig System version Assente Standard Super Super L Pati E A 10 C os be only 3 2 Environment Storage temperature 0 45 C Working temperature 5 32 C Max relative humidity 65 Dimensions and Weights Height 185 cm 1 cm Width 80 1 cm Depth 85 1 cm Maximum empty weight 230Kg 250Kg
5. 250Kg 250Kg Noise level The vending machine emits an A weighted sound pressure level below 70 dB Food Zone Variable height zone up to a maximum of 70 cm containing the drawers placed in the lowest position in the vending machine See Fig 1 LEGEND OF SYMBOLS USED Rev M 01 Symbol WARNING NECESSARY OPERATION TO KEEP PEOPLE SAFE CAUTION THE OPERATION CAN DAMAGE THE MACHINE OR CAUSE IT TO MALFUNCTION Page 3 d am ia n Serie EUR7 rheavendors O WARNINGS CAUTIONS The appliance should be be started up by skilled service personnel ONLY All operations described in this manual especially all maintenance operations concerning the electrical part should be carried out by skilled technical service personnel ONLY The vending machine is equipped with a safety switch that allows powering up all electrical parts only when the door is closed With this switch it is possible to power up the vending machine even with the door open for example to perform the test procedure on the vending motors Be careful that all moving parts spirals sliding anti theft panel etc are not accidentally activated This automatic vending machine is not intended for use by persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they are supervised or instructed on the use of the vending machine by a person responsible for their safety Children should be supe
6. 7 Token vvvvv DB parameters secur H Act ON Token f Rae Prices A f MDB parameters Cashless N 1 Cashless n 1 price association Prices A Prices B na Prices A MDB parameters Cashless N 2 Cashless n 2 price association Prices A Prices B RFID parameters RETD Price RFID price Association ia Prices A p brack t price Associatio Prices B Refrig Param s Probe 1 measure Internal temperature reading Read only Refrig Param s Sep probs d Internal temperature setting 0 50 C 40 temperature Refrig Param s NightMode temp Temperature setting in NightMode 0 50 C 0 Refrig Param s Probe 2 measure Refrigeration Unit temperature Read only reading Refrig Param s Security Temper Safety temperature 0 45 C 45 Refrig Param s Overtemper Time Overtemperature time 0 1440 min 30 Refrig Param s Refueling time Restocking time O 1000 min 120 Refrig Param s Connected probes Number of connected refrigerator Read only probes EVA DTS 3 Reset passcode Reset Security and Passcode codes Password required parameters audit dat Part Sale Numb Partial counter of number of vending Read only machine sales uait data Part Sale Value Partial counter of value of sales of Read only the selections await dat Motor Sale Numb Counter of number of sales per Read only selection audit data Sale Numb Lines oe of number of sales per price Read only uate data Tot Sale Numb General total number of vending Read only machine sal
7. EN 60 335 1 is available from Damian the replacement should ONLY be carried out by skilled service personnel Before all operations on the power cord make sure that the power supply plug is disconnected from its outlet GRILLE Dn A NNA TAPALE NATAAN TE p CABLE GLAND CABLE Remove the rear grille of the cabinet by unscrewing its fixing screws remove the cable gland from the grille open the cable gland and remove the cable Disconnect the cable socket from the electrical box and remove the cable to be replaced Repeat the operations described above in reverse order to install the new cable Check that the main switch found on the lower part of the cabinet See Fig 2 is in the OFF position and insert the plug into the power supply outlet then move the main switch to the ON position When the vending machine door is closed all of its electrical parts will be powered owing to the pressure exercised by the door on the safety switch black switch located on the right of the electrical box See Figure 2 USING THE SAFETY SWITCH The vending machine is equipped with a safety switch See Figure 2 that allows powering up all of its electrical parts only when the door is closed When it is necessary to power up the vending machine with the door open for example for loading products or programming the safety switch can be armed by inserting the special key and turning it 90 To disarm the safety switch i
8. Serie EUR7 rheavendors O When you have finished setting all of the motors that you wished to couple Twin Motors press 6 to continue the self learning procedure D This message appears on the display Self learning FTCA sensors Xxxx If the product drop sensors FTCA are installed on the vending machine XXX ON If the product drop sensors FTCA are not installed on the vending machine XXX OFF press 3 to confirm E The following message will appear shortly on the display Self learning Conn probes x Possible values 0 1 2 If the value is 0 zero there is no refrigerator probe connected the following message will appear when 3 is pressed Refrig operation OFF With OFF mode refrigerator operation is deactivated the self learning procedure ends when the 3 key is pressed and the vending machine returns to the programming menu No other modes can be selected If the value is 1 One there is just one refrigerator probe connected the following message will appear when the 3 key is pressed Refrig operation Drink amp Snack It is possible to confirm Drink amp Snack mode or alternatively select the OFF mode In Drink amp Snack mode refrigerator operation is activated without management of the safety temperature of the food zone the self learning procedure ends when the 3 key is pressed and the vending machine returns to the programming menu If the value
9. banknote press 4 to change the recognition security level Note 1 The value of the banknotes recognised by the payment system depends on the system itself refer to the relative documentation Note 2 the meaning and operation of the recognition security level depends on the payment system refer to the relative documentation TOKEN Visible and programmable only if an MDB banknote reader that foresees the Token function is installed To enable the token recognised by an MDB banknote reader MDB parameter f P Banknote stacker eee Token vvvvv Secur H Act ON Secur H recognition security level high Secur L low Enabl ON token enabled Enabl OFF token disabled Press 4 to change the recognition security level Press the 3 key to enable disable the token Note 1 the meaning and operation of the recognition security level depends on the payment system refer to the relative documentation gt CASHLESS If one or more cashless payment systems are installed in the vending machine it is possible to select the price bracket to be associated with these systems CASHLESS N 1 PRICE BRACKET ASSOCIATION Visible and programmable only if a Cashless payment system is installed If a cashless payment system is installed in the vending machine it allows selecting the price bracket to be associated with this system Settable values Prices A Price bracket A Prices B Price
10. bracket B Default Prices A MDB t J 1 gt gt ay AOR R Cashless N 1 Current value CASHLESS N 2 PRICE BRACKET ASSOCIATION Visible and programmable only if a Second Cashless payment system is installed If a second cashless payment system is installed in the vending machine it allows selecting the price bracket to be associated with this system Settable values Prices A Price bracket A Prices B Price bracket B Saas ic ee Cashless N 2 Current value Rev M 01 Pagina A 13 d am ia n Serie EUR7 rheavendors O RFID PARAMETERS Visible and programmable only if an RFID payment system is installed To set the parameters of the RFID payment system gt RFID PRICE BRACKET If an RFID payment system is installed in the vending machine it allows selecting the price bracket to be associated with this system Settable values Prices A Price bracket A Prices B Price bracket B See sala ae aoe Default Prices A p RFID Price brkt Current value gt RFID MACHINE CODES The correct machine codes Machine code A and B must be set in the vending machine in order for the RFID payment system to work correctly Contact the technical assistance service if problems should arise REFRIGERATOR PARAMETERS Visible and programmable only with Refrigerator operation other than OFF gt INTERNAL TEMPERATURE READING To
11. brackets on the wall Drill the wall and fasten the brackets using expansion bolts making sure that the brackets are positioned correctly Position the vending machine inside the brackets and fasten it firmly with the screws from above and the self locking nuts from below inside the machine Rev M 01 Page 5 d am ia n Serie EUR7 rheavendors O POWER SUPPLY The vending machine should only be connected to earthed electrical systems Before connection to the supply mains make sure that the earthing system is present that the supply voltage is 220 230 Volt that the outlet to which the machine will be connected is in good condition and approved for at least 10 Amp and that an omnipolar switch is installed upstream of it i e that switches off both power supply conductors with a single opening action except for the earth conductor with an opening of the contacts of at least 3 mm It is recommended that the outlet have an insulated residual current breaker Install the vending machine so that the power supply plug is easily accessible after you install it Check the appearance of the power cord to detect possible abrasions or other defects of the sheath or of the plug on the cord and replace it if necessary as described further on in this manual POWER CORD REPLACEMENT If it should become necessary to replace the vending machine s power cord the HO5VV F replacement cord which is in conformity with standard CENELEC
12. details When the following message appears on the display Left Nois Righ OK OK OK The following message will appear when the 3 key is pressed FTCA 2 Enabled Mot yy Sens xxx When the 3 key is pressed it will be possible to carry out a test delivery sale on the yy selection For each product delivered sold a beep will be emitted each time an object passes in front of the sensors and a different value will appear on the display in the Sens field through this information we understand that the FTCA system works correctly the higher the number Sens the easier it will be for the FTCA infrared system to detect the delivered product Press the 1 and 2 keys to change the selection indicated by the Mot parameter Press the 6 key to exit the submenu Rev M 01 Pagina A 20 damian rheavendors O Serie EUR7 SUMMARY TABLE Memorandum to be filled out after the programming under way x x Adjusted Menu Parameter Meaning Min Max Default oc General Param s Language Message language Italian General Param s LCD contrast LCD contrast setting 40 General Param s Operating mode Operating mode MDB General Param s DDD DD mm hh mm Clock setting DateTime Dsp Enabled D General Param s Enable Clock enable Disa
13. in Executive mode as described in Attachment A Programming Sheet turn the vending machine off and then on again and wait from 10 seconds to 2 minutes for communication with the payment system to be established Remember to programme the value of each step parameter also called coin scaling factor or minimum coin to the same value already entered during programming of the payment system Refer to the payment system documentation Enter the selling prices and any other programming data Refer to Attachment A Programming Sheet The vending machine is now ready for use Rev M 01 Page 7 d am ia n Serie EUR7 rheavendors O CIRCUIT BOARDS SLIDING PANEL PRODUCT DOOR EXECUTIVE connector FTCA connector THH HTH pa gt ES rN DISPLAY connector rane X KEYBOARD ie connector mmm d fal CEST MDB connector 0 TTT a t Legenda 2 CL1 CPU circuit board 7 Closing control microswitch 17 Sliding panel rack 3 FTCA sensor bars 10 Anti theft sliding panel 18 Sliding panel motor pinion 5 Levers for locking the Push door 11 Sliding panel motor 6 Two microswitches of the Push locking 13 Beginning end stroke microswitches Rev M 01 Page 8 d am ia n Serie EUR7 rheavendors O OVERTEMPERATURE CONTROL onLy MoDELS EUR7P x xx S In order to guarantee the preservati
14. of the right hand FTCA bar 3 and replace it if necessary If the problem is not resolved check CPU card operation OFF L10g High Light FTCA bars blinded error Perform the vending sensor test Attenuate the possible source of external light that bothers the FTCA bars _If the problem persists replace the FTCA bar s 3 OFF L10h Low Light FTCA bar darkened error Perform the vending sensor test Check the state of cleanliness of the FTCA bars 3 eliminating any elements that might obstruct passage of the light emitted by the LEDS If the problem persists replace the FTCA bar s 3 OFF L13 Sliding anti theft panel errors These error messages concern failures of the sliding anti theft panel 10 closing opening system For a quicker check perform the Sliding door test as explained further on OFF L13a Sliding Panel S D Mot Fault Sliding panel motor short circuited Check the operation of the sliding panel motor 11 and the relative wiring replace it if necessary OFF L13b SD Mot Disconn Sliding panel motor disconnected Check the motor 11 of the sliding panel 10 and the relative wiring Replace it if necessary OFF L13e Lock Pos TimeOut Sliding panel motor movement error At the end of an opening closing cycle the sliding panel does not close completely or is not detected to be closed or not open completely or is not detected to be open
15. problem persists update the software If the problem is not resolved after the update replace the CPU card 2 OFF L50 xxxx Unforeseen generic error Turn the vending machine off and then on again if the problem persists contact the technical assistance service providing the number in parentheses OTHER ANSWERS TO PROBLEMS THAT MIGHT ARISE A Before checking any electrical part move the main switch to the OFF position See Figure 7 MESSAGES RELATIVE TO MOTOR ANOMALIES During the selections or Diagnostic tests some motor anomaly messages might appear on the display these messages are listed below with the relative explanation as well as some possible solutions to the problem Motor xx Disconnected NR The motor is not connected to the CPU Check the connections and that the motor wiring is not interrupted Check correct operation of the motor microswitch and of the motor itself Try replacing one at a time the motor the CPU card the drawer and cabinet wiring Motor xx Short Circuit NR The motor is short circuited Check the good condition of the motor itself Check that the motor and its connections are not wet Check the connections and that the motor wiring is not short circuited Try replacing one at a time the motor the CPU card the drawer and cabinet wiring Motor xx blocked R The motor is blocked or absorbs too much current Check the correct assembly of
16. read the internal temperature of the vending machine Read only Programming Refrig Param s g Probe 1 measure Current value gt NTERNAL TEMPERATURE SETTING To set the internal temperature of the vending machine Settable values 0 50 C Programming j ap Default 40 C Perri ge PArang Probe 1 Temp set Current value gt NIGHT MODE INTERNAL TEMPERATURE SETTING Visible and programmable only with Vivilight Kit installed and Refrigerator operation other than Food amp Snack This parameter allows setting the internal temperature of the vending machine when the Night Mode function is activated Settable values 0 50 C The refrigerator temperature raising function is deactivated during the Night Mode period if the parameter is set to 0 Zero or to a value below the one set as standard internal temperature Set Std Temp T in the Ia Refrig Param s menu This parameter can also be programmed through the Energy Saving menu in the General Param s Refer to the Energy Saving section for further information on this function Programming Refrig Param s E g Night Mode temp Default 0 C Current value gt REFRIGERATION UNIT WORKING TEMPERATURE READING Only visible if 2 refrigerator probe present To read the working temperature inside the refrigeration unit evaporator Programming Read only Probe 2 measure S Current value gt
17. right Once all of the digits have been entered press the 3 Enter key to confirm and return to the previous point or press the 6 Esc key to exit typing without modifying the previous value TO EXIT PROGRAMMING Press the 6 Esc key to return to the selection of the menus Press the Programming key P found on the CPU card of the vending machine for about 4 seconds or press the 6 Esc key for a few seconds In any case if no key is pressed for more than 120 seconds you will automatically exit the programming phase Rev M 01 Pagina A 2 d am ia n Serie EUR7 rheavendors O DEFAULT VALUE USED AUTOMATICALLY BY A NEW OR REINITIALISED CARD GENERAL PARAMETERS gt MESSAGE LANGUAGE To establish the language of the messages that appear on the display Programming Default Italian General param io Language Current value gt LCD CONTRAST SETTING To set the contrast of the LCD 1 mm General param LCD Contrast Valore attuale gt OPERATING MODE To set the vending machine operating mode Settable values Test Vend to operate in free sale for example to perform the sale test Executive to operate with Executive payment systems MDB to operate with MDB payment systems Default MDB Current value Programming 1 General param Operating mode N B Make sure that when setting the parameter to Test Vend the vending machine allows sales of the products w
18. the condition of the motors This function does not change the vending machine configuration detected during the self learning procedure it simply limits itself to comparing the current condition of the motors with that of the last self learning procedure performed Programming Di j i Lagnostics Motor Verify gt gt gt gt Motor X x Where x x scrolls the motors in sequence If errors should be detected during the check the check itself stops and the following message appears Error XXXXXX Where xxxxxx is the detected error See the Installation and service manual Problems and relative solutions chapter Motor anomaly messages section for the list of anomalies and relative solutions From these error conditions it is possible to make the check sequence continue by pressing the 3 key or end it with the 6 key One of the following messages will appear at the end of the check sequence Check incorrect Conn motors XX This means that anomalies and or differences between the current configuration and the one detected during the last self learning procedure have been detected XX indicates the number of the currently recognised motors Check OK Conn motors XX This means instead that anomalies and or differences between the current configuration and the one detected during the self learning procedure have not been detected XX indicates the number of the recognised motors In the eve
19. 006 e soddisfa i requisiti essenziali della Direttiva 98 37 CE Declares that the machine described on the identification plate is in conformity with the legislative provisions of the following Directives of the following regulations 2006 95 CE and 2004 108 CE EN 60335 1 2002 A1 2004 A11 2004 A12 2006 EN 60335 2 75 2004 A1 2005 A11 2006 EN 55014 1 2000 A1 2001 A2 2002 EN55014 2 1997 A1 2001 EN 55015 2002 A1 2001 A2 2002 EN 61547 1995 A1 2000 EN 61000 3 2 2000 A2 2005 EN 61000 3 3 1995 A1 2001 A2 2005 EN 50366 2003 A1 2006 and satisfies the basic requirements of Directive 98 37 CE Castellanza 21 February 2007 Presidente C d A Managing Director GENERAL WARRANTY CONDITIONS In compliance with the laws the device is guaranteed for 12 twelve months from the purchase date confirmed by a delivery document issued by the manufacturer By warranty we mean the free of charge repair or the replacement on the manufacturer s premises of those parts of the device recognised as faulty because of defects in manufacturing The faulty parts will be sent back by the customer ex manufacturing works If some parts under warranty must be repaired or replaced on the customer s premises by personnel sent by the manufacturer the labour costs and travel expenses will be charged to the customer The warranty does not cover those parts which are faulty because of negligence or carelessness inco
20. 2 key found on the CPU card for approx 3 seconds See Page A 2 gt MANUAL MOTOR TEST Select this item to test the individual motors making them carry out a sales cycle Programming Diagnostics g Mot Manual Test gt gt gt gt m p Motor I X X Use the 1 and 2 keys to scroll through all of the motors detected during the self learning procedure When the 3 key is pressed briefly the current motor will be activated the following message will appear if a malfunction occurs Error XXXXXX Where xxxxxx is the detected error See the Installation and service manual Problems and relative solutions chapter Motor anomaly messages section for the list of anomalies and relative solutions Rev M 01 Pagina A 17 d am ia n Serie EUR7 rheavendors O The general test cycle will begin instead when the 3 key is kept press for about one second during this cycle the vending machine will carry out a sales cycle in sequence for each gearmotor detected by the self learning procedure starting from the current motor up to the last motor of the vending machine In the event of a defect on one of the motors the test will be interrupted and the relative error message displayed The general test cycle will be interrupted when keeping any key pressed until the end of the sales cycle of the current motor Press the 6 key to exit the submenu gt MOTOR VERIFY Select this item to perform a quick check of
21. IS DISPLAYED During normal vending machine operation some malfunctions of some motors may occur These malfunctions generate errors that can be automatically reset by the vending machine R or that can be not resettable NR and put the selection out of order see above Even if operation of the selection has been automatically reset when the machine was turned on the error remains stored and must be deleted manually in diagnostics to keep the message from reappearing To check which motors and which problems have been stored enter into Diagnostic in the out of order motors menu see relative chapter WHEN MAKING A SELECTION SELEC X X INOVERTEMPERATURE IS INDICATED If some selections are out of order indicated by the Selection xx in Overtemperature message this is due to the intervention of the refrigerator safety control ERR LO9 refrigeration unit timeout error which has put the drawers set in the vending machine Food zone out of order See Overtemperature control section Entering in programming you will be asked if you wish to restore operation by resetting the error t ERR L09 Press key 1 to reset the error ES 2 NO Press key 2 to NOT reset the error When key 1 is pressed the selections will be active again WHEN MAKING A SELECTION SELECTION X X NOT ACTIVE IS INDICATED If some selections are out of order indicated by the Selection x x not active message t
22. MULTANEOUSLY When making a selection two or more motors even far apart run simultaneously Check that a motor connection was not inverted following a maintenance operation The motor with the inverted wiring might not be among those that rotate simultaneously Check the good condition of the wiring of the motors of the vending spirals Replace the motor and or connection wiring if necessary Make sure that the Twin motors function is not activated If the problem persists make sure that the CPU card works and replace it if necessary Rev M 01 Page 13 d am ia n Serie EUR7 rheavendors O THE MACHINE DOES NOT REACH THE REQUIRED TEMPERATURE Before carrying out any operation on the refrigeration unit and in particular before checking A any electrical part move the main switch to the OFF position See Figure 7 Check the condition of the fuses See the Fuse check chapter Make sure that dust and foreign materials do not block the refrigeration unit air passage Check that the condenser cooling fins are not blocked by dirt or foreign bodies and clean them if necessary to access the refrigeration unit see the Refrigeration unit disassembly and reassembly chapter Check that the set temperature is neither too high nor too low referring to the programming sheet Check that the internal air circulation fan works correctly Check that the refrigeration unit compressor works and that the cooling fan loc
23. apid 250 V supply work the display does not turn on Rev M 01 Page 15 d am ia n Serie EUR7 rheavendors O ROUTINE MAINTENANCE AND LUBRICATION During the maintenance and lubrication operations do not perform any operation other than those indicated See Figure 5 for the references in parentheses Check Correct operation of the door safety switch Correct operation of the sliding panel closing amp 3 months and opening microswitches Check cleaning of vending Check cleaning of the refrigeration unit 1 year condenser fins N B cut the periodicity by half for installations in especially dusty locations SAFETY SWITCH CHECK 3 A During the safety switch check do not perform any operations other than those indicated Check correct operation of the safety switch 15 by opening and reclosing the door with the vending machine on make sure that the vending machine turns off when the door is being opened and that it turns on again only after it has been closed completely SLIDING PANEL CHECK 9 Sliding panel 10 operation can be checked by performing a door closing and opening test see programm gt diagnostics gt Sliding panel test CHECK CLEANING OF FTCA VENDING SENSORS To clean the LED barriers of the FTCA system 3 which are protected hidden by the sliding anti theft panel during normal operation it is necessary to open it performing a sliding panel 10 opening te
24. ated between the compressor and the condenser of the refrigeration unit works properly If the compressor does not start working when the LED on the card indicates that it is activated check and if necessary replace the electric starting capacitor the Clicson or the amperometric relay located in the box mounted close to the compressor With the compressor operating check that the evaporator actually gets cold Check that the two evaporator fastening hooks located on the shelf under the first drawer are closed and the evaporator properly hooked If it is not possible to identify the cause of the problem contact an authorised service centre Rev M 01 Page 14 d am ia n Serie EUR7 rheavendors O FUSES MAIN SWITCH Press to cancel motors OUT OF ORDER ae HT SAFETY SWITCH Press to enter into programming The vending machine is equipped with fuses mounted as shown in the following table POSITION INSCRIPTION TYPE PROTECTED CHECK WHEN CIRCUITS 5x20 T6 3 Refrigeration unit The vending machine does not 5x20 T6 3 General The vending machine does not 6 3 A delayed 250 V 24 28V work 5x20 T6 3 General 230y The vending machine does not 6 3 A delayed 250 V work Sc rs 5x20 T6 3 General 2309y The vending machine does not 6 3 A delayed 250 V work E 5x20 F1 CPU power The vending machine does not 1A r
25. bled Enabled General Param s SaveMode delay Activation delay in SaveMode_ 0 120 minutes 0 General Param s Light in SaveMode Light intensity in SaveMode 0 100 100 NightMode NightMode Activation P 00 General Param s timetable Timetable 19 00 7 00 General Param s NightMode Light Light intensity in NightMode 0 100 100 Temperature setting in pD General Param s NightMode temp NightMode 0 50 C 0 General Param s aes ensca Refrigerator Operation Aut operation 0 Disabled 2 Enable General Param s FTCA enabling Vending sensor enabling 1 Enable Nostep 3ste 2 Enable 3step P General Param s FTCA max 3 sel FTCA max 3 selections enableg i Enabled Disabled General Param s Decimal point Decimal point position 0 3 2 General Param s Code Mode Internal code software Read only General Param s Software versions Displays software versions General Param s Default P Reset Card reinitialisation Password required General Param s Protected param Protected parameters Password required Reset Temp ae Reinitialise overtemperature times Price managemen Price A N xx Value of each ee e 0 635 35 2 00 associable A bracket prices ae wey T Enabled Price managemen Price B enabling Enabling B price bracket Disabled Disabled Price managemen Price B N xx Value of each ofthe 44 0 635 35 2 00 associable B bracket prices 0 OFF Disable Price management Enabl Dir Sel Enabling
26. c operation restoration will be attempted again if possible Message code Message text Problem description solution OFF L01 Temperature probe 1 error These messages indicate a problem with the probe that measures the temperature inside the vending machine This probe is located on the inner right wall near the 1 low drawer towards the bottom of the vending machine Note Probe operation is only checked at the moment the vending machine is turned on OFF L01a OFF L01b Probe 1 defective Disconnected Probe 1 disconnected error Turn the vending machine off and then on again verify in programming that the temperature value read by probe 1 is correct see programming sheet Try touching the probe if the value shown on the display does not change check the wiring and replace the probe if necessary If once the probe has been replaced the problem is repeated the fault might be due to the CLP1 power board located in the electrical box Short circuit Probe 1 short circuited error Turn the vending machine off and then on again verify in programming that the temperature value read by probe 1 is correct see programming sheet Try touching the probe if the value shown on the display does not change check the wiring and replace the probe if necessary If once the probe has been replaced the problem is repeated the fault might be due to the CLP1 power board located in
27. damian rheavendors O snack europa INSTALLATION AND SERVICE PROGRAMMING This manual is for skilled service personnel only DAMIAN S R L VIA RAGAZZI DEL 99 N 30 21053 CASTELLANZA VA ITALY Rev M 01 Vers Software 0 5b or follow d am ian Serie EUR7 rheavendors O IMPORTANT This automatic vending machine is not intended for use by persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they are supervised or instructed on the use of the vending machine by a person responsible for their safety Children should be supervised to make sure that they do not play with the vending machine IDENTIFICATION USE AND TECHNICAL DATA This manual refers to EUR7 series SNACK EUROPA automatic spiral vending machines with number of drawers number and type of vending spirals varying from model to model MARKING PLATE SERIAL NUMBER d KEYBOARD Oo j z MARKING PLATE FOOD ZONE SERIAL NUMBER Variable x 7Ocm eexeeyevenyesyenyee e AEE A i SSSE8eee8 REFRIGERATION UNIT eceeececeese MARKING PLATE eeseescesso MAIN SWITCH The intended use for EUR7 series SNACK EUROPA automatic spiral vending machines consists of automatically distributing solid products or products in solid package pre packaged foods snacks bottled drinks etc and non food items For food products
28. direct selections 1 ON Manualreset Disabled 2 ON Auto Reset Price management Drawer L C Direct selection association 1 S2 S3 Price associated with drawer P L P peas Price management Drawer L C Line L column C 0 44 01 or 2 ss Enabled Price management Enable Price Dsp Display of the selling price Enabled Disabled ea Min coin values Coin scaling factor 0 1000 000 01 parameters MDB parameters Maximum credit Maximum accepted credit 0 635 35 0 MDB parameters MinTube NoChange Minimum coins to turn no 5 change indicator light on MDB parameters MinTube Change Minimum coins for giving 2 change MDB parameters Obligatory Sale Compulsory sale Erableg n Disabled j Disabled Enab Man Manual emptying of the coin Enabled M t DB parameters Dispens tubes Disabled Disabled Rev M 01 Pagina A 21 damian rheavendors O Serie EUR7 Memorandum to be filled out after the programming in progress Menu Parameter Meaning Min Max Default Adjuste d to 0 Single no Chang 1 Single MDB parameters Sale Modalit MDB MDB sales modes 1 Single Change 2 Multi Vend Change Coin nn vvvvv MDB parameters tay tubes xxx yyy Coins present z 2 Token n DB parameters In tubes xxx yyy Tokens present 7 7 Bill nn vvvvv DB parameters secur X Act ON Banknotes present te
29. e bottom and C column indicates the position on the drawer Where XX indicates the price line and VVVVvV the relative price Press the 1 and 2 keys to scroll through the available selections Press the 3 key to vary the association with the selling price line for the current selection scroll through the price lines with the 1 and 2 keys after having selected the desired one confirm it with the 3 key gt DISPLAY OF THE SELLING PRICE Enables the display of the selling price of the product requested by the customer at the time of the sale Settable values Enabled ON displayed Disabled OFF displayed Default Enabled Current value Ens Price management ic g Enable Price Dsp EXECUTIVE PAYMENT SYSTEM PARAMETERS Visible and programmable only with Operating mode Executive gt VALUE OF EACH STEP OR COIN SCALING FACTOR The value of the coins and the selling prices are always expressed as multiples of a base coin of minimum value During operation with Executive payment systems this value must be the same as the one set in the payment system Settable values 0 1000 Programing Default 00001 Price management m Min coin value Current value Note 1 if during entering of the selling prices and of the values of the various coins and banknotes they are not multiples of the Value of each step parameter they will automatically be rounded off MDB PAYMENT SYSTEM PARAMETERS
30. e individual vending selections available These 44 prices comprise the A price bracket i e the basic prices that will be used as reference in the price selection association For the EUR7 vending machines it is possible to manage a second bracket of another 44 price lines the B price bracket to be used for example for sales made with payment systems to which we wish to assign dedicated prices i e Cashless or RFID systems The prices of the B bracket will automatically be associated with the same selections associated with the A bracket For example if price line 1 of the A bracket is associated with selection 2C it will automatically be associated with price line 1 of the B bracket also A BRACKET SELLING PRICES The 44 available selling price lines of the A bracket can be set as follows Default 2 00 for all selections Soe eee Product Prices A gt gt gt J Price A N xx VVVVV Press keys 1 and 2 to scroll through the available price lines with xx going from LO1 to L041 plus S1 S2 S3 which correspond to the price lines for the direct selection buttons max 3 optional buttons Press the 3 key to select the value VVVVV of the price line to be varied Enter the new value pressing the numbers on the keyboard confirm the price by pressing the 3 key again Note 1 if the entered value is not an exact multiple of the Min coin values parameter see furthe
31. ee Audit dat fi f ue ale Partial n sales Current value Serie EUR7 gt PARTIAL COUNTER OF VALUE OF VENDING MACHINE SALES To read the total amount collected by the vending machine since the last reset ee Audi uart daba Part Val Sales Current value COUNTER OF NUMBER OF SALES PER SELECTION To read the total absolute and partial since the last reset number of sales for each individual vending machine selection Audit data Num Sales Motors ahaa uy EEM P XXXXX T XXXXX COUNTER OF NUMBER OF SALES PER LINE SALES PRICE To read the total absolute and partial since the last reset number of sales for each product price line Fee A i l i nek eae Num Sales Lines asaya io En P XXXXX T XXXXX gt GENERAL TOTAL NUMBER OF VENDING MACHINE SALES To read the general total number of vending machine sales Fa ae Audit date Tot Num Sales Current value gt GENERAL TOTAL VALUE OF VENDING MACHINE SALES To read the general total of the amount collected by the vending machine Fea ae Audie data f Tot Val Sales Current value AUDIT DATA RESET To reset the Partial totals counted by the vending machine oo Audit data Audit Data Reset TPR l Audit Data Reset 1 YES 2 NO Rev M 01 Pagina A 16 d am ia n Serie EUR7 rheavendors O DIAGNOSTICS N B the programming TimeOut is disabled in the Diagnostics submenus therefore it is only possible to exit programming man
32. ehold waste Contact your local dealer for further information regarding disposal 2 In countries outside the EU If you wish to get dispose of this product please contact the local authorities for information on the correct disposal method WARRANTY Damian S r l provides a warranty for its own products that is in conformity with the specific national laws The warranty begins on the date shown on the sales document The warranty does not include damage caused by natural wear overload improper use or any other breakdown not caused by a manufacturing defect The warranty conditions are given at the end of this manual Rev M 01 Page 17 damian rheavendors O snack europa Attachment A PROGRAMMING SHEET This attachment is an integral part of the manual and must remain with it DAMIAN S R L VIA RAGAZZI DEL 99 N 30 21053 CASTELLANZA VA ITALY Rev M 01 Vers Software 0 5b or follow d am ia n Serie EUR7 rheavendors O PROGRAMMING METHOD PS1 key A re a v 5 4 5 Ps1 s 4 ef 5 710 a 28 ia P Programming key TO ENTER INTO PROGRAMMING Open the vending machine power it up using the special key on the safety switch and press the pushbutton P found on the CPU card of the vending machine see the above figure for about 2 sec
33. en replaced the problem is repeated the fault might be due to the CLP1 power board located in the electrical box OFF L04 Executive OFF Executive OFF No communication with the Executive system Check the 24Vac power supply coming from the transformer and the connection of the relative wiring with the 15 pin connector Check the Executive signal wiring If the problem is not resolved check CPU card operation Rev M 01 Page 10 d am ia n Serie EUR7 rheavendors O Message coda Message text Problem description solution OFF L10 FTCA vending sensor error These error messages may appear when the vending machine is turned on or right before a sale OFF L10a FTCA sensors OFF Chk cable Chang FTCA bars not connected OFF L10b Check the condition of the wiring and of the connections of the FTCA bars 3 OFF L10c and replace wiring if necessary If the problem persists replace the FTCA bars 3 one at a time starting from the one on the right If the problem is not resolved check CPU card operation OFF L10e Check LeftSensor Left hand FTCA bar error Check the condition of the wiring and of the connection of the left hand FTCA bar 3 and replace it if necessary If the problem is not resolved check CPU card operation OFF L10f Check RightSens Right hand FTCA bar error Check the condition of the wiring and of the connection
34. es Audit data Tot Sale Value General total value of vending Read only machine sales Audit data Audit Data Reset Audit data reset Password required Diagnostic Motors Out of Ord Search for out of order motors Diagnostic Manual MotorTest Motor sales cycle test Diagnostic Motor Verify Quick motor test Diagnostic Motor Slearning Motor config self learning Diagnostic Test anti panel Sliding anti theft panel test Diagnostic Test block Push Push product door test Diagnostic FTCA sensor test Vending sensor test NOTE Default Value used automatically by a new unprogrammed or reinitialised card Rev M 01 Pagina A 22 EC Damian S r l Via Ragazzi del 99 n 30 21053 Castellanza Varese Italy Tel 39 0331 322020 Fax 39 0331 322030 DECLARATION OF CONFORMITY a Declaration not valid without the identification plate _l Dichiara che la macchina descritta nella targhetta di identificazione conforme alle disposizioni legislative delle seguenti Direttive delle seguenti norme 2006 95 CE e 2004 108 CE EN 60335 1 2002 A1 2004 A11 2004 A12 2006 EN 60335 2 75 2004 A1 2005 A11 2006 EN 55014 1 2000 A1 2001 A2 2002 EN55014 2 1997 A1 2001 EN 55015 2002 A1 2001 A2 2002 EN 61547 1995 A1 2000 EN 61000 3 2 2000 A2 2005 EN 61000 3 3 1995 A1 2001 A2 2005 EN 50366 2003 A1 2
35. h the vending machine does not give change Settable values 0 5 Programming Default 2 it oni Tt Current value COMPULSORY SALE Visible and programmable only if MDB coin return payment system installed If Enabled the MDB payment system does not give change before a sale to prevent it from being used as a coin changer Settable values Disabled OFF Enabled ON Default Disabled MDB KESS Obligatory sale Current value MANUAL EMPTYING OF THE COIN TUBES Visible and programmable only if MDB coin return payment system installed If activated it enables the manual emptying of the coin tubes through the pushbuttons on the MDB payment system Settable values Disabled OFF Enabled ON The emptying of the coin tubes performed by the programming is carried out as described further on Default Disabled MDB parameter i aa Enab Man Dispens Current value Rev M 01 Pagina A 11 d am ia n Serie EUR7 rheavendors O MDB SALES MODES Visible and programmable only if MDB coin return payment system installed To select the sales mode with an MDB payment system Settable values 0 Single NoChang Single sale without change at the end of the sale the change is cancelled 1 Single Change Single sale with change at the end of the sale the change is returned automatically 2 Multi Vend Mult
36. han Food amp Snack it allows setting a higher operating temperature only activated during those time intervals The energy saving function setting modes are given below SAVE MODE ACTIVATION DELAY Visible and programmable only with Vivilight Kit installed This parameter allows setting the time in minutes that must elapse without anyone using the vending machine before the Save Mode function is activated attenuation of the intensity of the LED lamps Settable values 0 120 minutes Set the parameter to Zero 0 to deactivate the function Default 0 minutes Programming General param a p Energy Saving ended SaveMode delay Current value SAVE MODE LIGHT INTENSITY Visible and programmable only with Vivilight Kit installed This parameter allows setting the luminous intensity in of the LED lamps that light up the display window when the Save Mode function is activated Settable values 0 100 Default 100 General param i Current value NIGHT MODE TIMETABLE Visible and programmable only with Vivilight Kit installed This parameter allows setting the start and end times of the Night Mode function Set the times to 00 00 00 00 to disable the function Default 19 00 07 00 Programming General param fi E 3 Energy Saving B EAF Night Mode times hh mm hh mm NIGHT MODE LIGHT INTENSITY Visible and programmable only with Vivilight Kit i
37. he value 21613 in point 3 Rev M 01 Pagina A 7 d am ia n Serie EUR7 rheavendors O PROTECTED PARAMETERS Protected parameters are basic settings of the vending machine protected by Password parameters that were set at the factory whose variation is not recommended unless suggested by the technical support service Improper variation of these parameters could compromise the correct operation of the vending machine General param 00000 RESETTING OVERTEMPERATURE COUNTERS Visible and programmable only with Refrigerator operation Food amp Snack If operator intervention is prolonged and the vending machine stays off or in overtemperature status for a length of time close to the time set it is possible that at the end of the intervention when the operator has already moved away the vending machine is not able to bring the temperature back below the set threshold in the residual time remaining To prevent false out of order indications after prolonged operator intervention the various counters can be initialised through this function R T i m reset Important This function must be used in conformity with the applicable regulations in force regarding the preservation of sold products MANAGEMENT OF SELLING PRICES The series EUR7 vending machines can manage 44 price lines i e 44 different prices from L01 to L41 plus 3 S1 S2 S3 dedicated to direct selections which will be associated with th
38. his indicates a problem relative to the storing of the configuration because the selection made is not stored as active by the vending machine Make sure that you have made the correct selection Carry out the Motor Verify procedure found in the diagnostic menu Carry out a new self learning procedure of the motors through the reset of the circuit board If the motor is not recognised during the self learning procedure see the relative error further on WHEN MAKING A SELECTION SELECTION X X OUT OF ORDER IS INDICATED If some selections are out of order indicated by the Selection x x out of order message this indicates the presence of a problem relative to the motor For a detailed analysis of the type of error that generated the out of order condition use the Diagnostic menu out of order motors submenu and the preceding chapter Motor anomaly messages NOTE It is possible to cancel the Out of Order condition of the motors without entering into programming by pressing the PS2 key found on the CPU card for approx 3 seconds See Fig 7 SOME MOTORS ARE NOT DETECTED DURING THE SELF LEARNING PROCEDURE Check the wiring and good condition of the unrecognised motors as well as the good condition and correct insertion of the connectors on the bottom of the vending drawers After performing the above carry out the procedure indicated for the Disconnected motor error SEVERAL MOTORS RUN SI
39. igeration unit control probes that are connected Programming Refrig Param s i Comnected probes Read only Current value EVA DTS PARAMETERS gt PASSWORD CODE RESET EVA DTS To reset the Security and Passcode codes foreseen by the DDCMP protocol EVA DTS to prevent anyone from being able to access and download the data relative to the vending machine proceeds using an IRDA handheld device oo oe EVA DT ram g 1 ee aaa Reset Passcode a Sata ay 1 00000 Thanks to these protection codes the data can be downloaded only if those set on the handheld device coincide with those acquired previously by the vending machine If the 2 codes do not correspond the following error message will appear DDCMP error 9071 In this case the codes acquired by the vending machine must be reset Reset Passcode by entering the password At this point the vending machine has no protection code and will reacquire a new one at the time of the next connection with a handheld device that has a code other than 0 set Rev M 01 Pagina A 15 damian rheavendors O AUDIT PARAMETERS NOTE It is possible to display a minimum list of sales data on the automatic vending machine If an MDB system is installed the vending machine collects more detailed data available in the EVA DTS format gt PARTIAL COUNTER OF NUMBER OF VENDING MACHINE SALES To read the total number of vending machine sales since the last reset Ee
40. iple sale the residual credit is returned only if requested Current value gt COINS AND TUBES If there is an MDB change return coin box installed in the vending machine it will be possible to set the reading and or recognition of the quantity and or value of coins or tokens present in the coin box tubes The following coin and tube parameters can be set by selecting this function COINS MANAGED BY THE COIN RETURN SYSTEM Visible and programmable only if MDB coin return payment system installed To read the value of the coins present in the MDB payment system tubes and to enable or disable acceptance of these coins also to empty the coins present in the tubes oo MDB parameter Coins and tubes l gt gt gt m Coin nn vvvvv In tubes xxx yyy nn number of the coin vvvvv value of the coin xxx number of coins in the tube if the tube is not enabled it displays yyy ON coin enabled OFF coin disabled Press the 3 key to enable disable the coin Press the 4 key to manually empty from 1 to 9 coins from the indicated tube Note 1 The value of the coins recognised by the payment system depends on the system itself refer to the relative documentation Note 2 With some MDB payment systems the parameter indicating the quantity of coins present could be handled by the payment system itself Refer to the documentation of the payment system in use TOKENS PRESENT Visible and pr
41. is 2 Two there are two refrigerator probes connected the following message will appear when the 3 key is pressed i or 3 Refrig operation Refrig operation Drink amp Snack FOOD amp Snack It is possible to confirm FOOD amp Snack mode or alternatively select the Drink amp Snack mode or OFP Management of the safety temperature is activated when FOOD amp Snack mode is selected the following message will appear when the 3 key is pressed Security Temper gt Pe O26 The safety temperature value is displayed with the possibility of changing it press 3 to confirm If an incorrect message appeared on the display during phase E carry out the operations described in the Installation and service manual referring to the OFF L01 and OFF L02 messages F This message appears on the display Code Mode gt XXX Self learning of the internal parameter software code mode press 3 to confirm G Once the last parameter has been confirmed the self learning procedure ends and the vending machine returns to the programming menu Reinitialisation allows keeping all of the other settings active e g product prices Price associations etc avoiding reprogramming them Important If it should be necessary to completely reset the circuit board with the total deletion of the programming parameters the reinitialisation procedure described above must be carried out entering t
42. ithout deducting the credit gt CLOCK SETTING To set the current date and time General param dddd mm yy hh mm Current value gt CLOCK VISUALISATION ENABLE To activate or deactivate visualisation of the current time while the vending machine is awaiting a sale Settable values Disabled OFF Enabled ON a Default enabled p i Time Dsp Enable Current value gt ENERGY SAVING PROGRAMMING To activate and set the parameters of the energy saving functions which are only available if the vending machine has the Vivilight Kit installed Energy Saving allows activating two separate energy saving functions Save Mode function Kicks in after a programmed vending machine inactivity time and reduces the electrical consumption of the vending machine working for example on the reduction of the lighting and the turning off of indicator lights and non essential components Night Mode function Kicks in during programmed time intervals for example during nighttime hours after a period of vending machine inactivity and reduces the electrical consumption of the vending machine to the minimum working for example with the turning off of the lighting of indicator lights and of non Rev M 01 Pagina A 3 d am ia n Serie EUR7 rheavendors O essential components Furthermore if the vending machine is NOT programmed to contain perishable products Refrigerator operation parameter other t
43. mbers on the keyboard confirm the price by pressing the 3 key again Note if the entered value is not an exact multiple of the Min coin values parameter see further ahead it will automatically be rounded off and the new value will have to be reconfirmed with the 3 key gt ENABLING DIRECT SELECTION Programmable only with keyboard with direct selection system and FTCA installed To activate or deactivate management of the direct selection with keyboard with direct selection system and FTCA system installed Settable values 0 OFF Disabled Selling direct selections Disabled 1 ON ManualReset Selling direct selections Enabled with manual reset Each time it is turned back on is required the manual reset of empty 2 ON Auto Reset Selling direct selections Enabled with auto reset Each time it is turned back on is automatically run the reset of empty M P e mara gonSn Enabl Dir Sel Current value Enabling the management of direct selections can be associated with direct selection buttons S1 S2 S3 one or more selections DIRECT SELECTION ASSOCIATION Visible and programmable only with Enabling direct selection enabled This function allows you to associate to direct selection buttons S1 S2 S3 one or more selections as well as calling it a Direct Selection All the sections that are associated with a single button must contain the same product Pressing the key to Direct Selection the vendi
44. n order to cut off power to the electrical parts turn the switch key 90 and remove it from the switch Rev M 01 Page 6 d am ia n Serie EUR7 rheavendors O INSTALLATION OF PAYMENT SYSTEMS The payment system installation and removal operations must be carried out with the power supply switched off moving the main switch to the OFF position MDB PAYMENT SYSTEMS Connect the payment system to the CPU card 2 being careful to connect the cable on the proper MDB connector on the CPU card See Figure 5 Turn the vending machine on and programme it for operation in MDB mode as described in Attachment A Programming Sheet also refer to the documentation relative to the system itself for the MDB payment system settings Enter the selling prices and any other programming data Refer to Attachment A Programming Sheet The vending machine is now ready for use EXECUTIVE PAYMENT SYSTEMS OPTIONAL KIT The Executive Kit optional must be installed for operation of the executive payment systems Connect the Molex 15 pin female power connector of the vending machine to the corresponding connector on the payment system Refer to the payment system documentation Connect the serial connector of the payment system to the CPU card 2 using the special adapter cable being careful to connect the adapter cable on the proper connector See Figure 5 Turn the vending machine on and programme it for operation
45. ng machine starts sell from the last spiral which provided the product If this spiral was exhausted the system FTCA will detect the failure to selling the system automatically attempt to deliver the product from the next spiral associated with the same direct selection If all spirals associated are exhausted the selection will be automatically put out of service Programming Price management m g Assoc Dir Sel e ee ie a d Drawer R C XX VVVVV Rev M 01 Pagina A 9 d am ia n Serie EUR7 rheavendors O Where L line indicates the number of the drawer from the bottom and C column indicates the position on the drawer Where xx indicates the price line S1 S2 S3 dedicated to direct selections and vvvvv the relative price Press the 1 and 2 keys to scroll through the available selections Press the 3 key to confirm the current selection Press the button of direct selection from associate or press 1 or 2 to choose from choosing L01 the selection is no longer associated with any direct selection button Press 3 to confirm the change Repeat the same procedure for all selections from associate gt PRICE ASSOCIATION This function allows associating a price of the A price bracket and the respective B bracket price to each available selection gt gt gt Programming Price management a i Price assoc Drawer R C XX VVVVV Where L line indicates the number of the drawer from th
46. nstalled This parameter allows setting the luminous intensity in of the LED lamps that light up the display window when the Night Mode function is activated Settable values 0 100 Programming Default 100 General param O n Energy Saving 7 Ta Night Mode light Current value NIGHT MODE INTERNAL TEMPERATURE SETTING Visible and programmable only with Vivilight Kit installed and Refrigerator operation other than Food amp Snack This parameter allows setting the internal temperature of the vending machine when the Night Mode function is activated Settable values 0 50 C Default 0 C Energy Saving Scr Night Mode Temp Current value The refrigerator temperature raising function is deactivated during the Night Mode period if the parameter is set to 0 Zero or to a value below the one set as standard internal temperature Set Std Temp t in the Refrig Param s menu This parameter can also be programmed through the Refrig Param s menu Rev M 01 Pagina A 4 d am ia n Serie EUR7 rheavendors O gt REFRIGERATOR OPERATION Visualisation only programmable by reinitialising the card To visualise the operating mode of the refrigeration unit Default Self learned General param j Current value The three possible operating modes programmable by reinitialising the card are Food amp Snack enables management of the safety temperat
47. nt of Check OK at the end of the motor check cycle the vending machine s original configuration is completely restored and the out of orders reset N B at each check the motors rotate just a few degrees therefore repeating the check several times in succession the motors could lose alignment we therefore recommend realigning the motors for example by carrying out a manual motor test as described previously in this manual Rev M 01 Pagina A 18 d am ia n Serie EUR7 rheavendors O gt MOTOR SELF LEARNING Select this item to repeat the self learning of the motors present in the vending machine this action is only allowed if a password is set in the protected parameters menu suai Self learning Conn motors xXx Ee ae PragNOSEIES Motor Slearning gt SLIDING PANEL TEST Select this item to perform the sliding anti theft panel operation test pragnostitcs i Anti tft p test p rm o gt P Pot TTot K W ZZZ 2222 When the following message appears on the display Pot TTot M C P X K W ZZZ 2222 L Y Press the 1 key to open the anti theft panel Press the 2 key to move the anti theft panel in the closed position allowing the product door opening Press the 3 key to close the anti theft panel M Sliding Panel microswitch X 1 Micro switch pressed Sliding Panel fully closed X 0 Micro switch not pressed Sliding Panel fully open or not fully closed L Locking lever product removal do
48. ogrammable only if MDB coin return payment system that foresees the Token function is installed To read the number of tokens present in the MDB payment system tubes and to enable or disable recognition of these tokens Ee MDB parameter Coins and tubes 7 AA Token n In tubes xxx yyy n number of the token xxx number of tokens in the tube if the tube is not enabled it displays yyy ON token enabled OFF token disabled Press the C key to empty the tube manually Default 1 Single Change gt BANKNOTES AND STACKER If there is an MDB banknote reader installed in the vending machine the reading and or recognition of the quantity and or value of banknotes or tokens present in the MDB payment system will be possible The following banknote and stacker parameters can be set by selecting this function Rev M 01 Pagina A 12 d am ia n Serie EUR7 rheavendors O BANKNOTES PRESENT Visible and programmable only if an MDB banknote reader is installed To read which and how many banknotes are present in an MDB payment system and to enable recognition of them MDB parameter ct p Banknote stacker gt gt u Secur H Act ON nn number of the banknote vvvvv value of the banknote Secur H recognition security level high Secur L low Enabl ON banknote enabled Enabl OFF banknote disabled Press 3 to enable disable the
49. on of the products for sale the vending machine controls that the internal temperature does not exceed a given threshold called safety temperature for a period longer than the overtemperature time The overtemperature control function is managed through 3 parameters A Safety temperature B Overtemperature time Set C Restocking time The overtemperature is only controlled in mode operating of the refrigeration unit Food amp Snack setting the A Safety temperature parameter to a value below 40 C During normal vending machine operation if the internal temperature exceeds the Safety temperature A for a period longer than the Overtemperature time B the ERR LO9 error will be generated which will put the drawers set in the Food zone of the vending machine out of order The period of time in which the vending machine is off is always considered beyond the Safety temperature A If the vending machine is turned off and then on again e g after restocking the Overtemperature time B is prolonged by a value equal to the one set in the Restocking time C parameter Each time it is turned back on if the internal temperature exceeds the Safety temperature A but the conditions for generating the ERR L09 error have not occurred see above the following message will appear on the display for approx 15 sec Overtemp XXXMin YY Y gt ZZ Z C XXX Mi
50. onds avoid reclosing the vending machine so as not to damage the safety switch When the safety switch is armed with the special key do not perform any operations other than those described TO CHOOSE THE PARAMETER THAT YOU WISH TO PROGRAMME Select the menu using keys 1 A or 2 V the messages relative to the various menus will appear on the second line of the display When the message relative to the desired menu appears press the 3 Enter key to confirm The parameter name will appear on the first line of the display the currently set value on the second line Select the menu parameter using the 1 A or 2 v keys the messages relative to the various menu parameters will appear in sequence on the first line of the display until it starts again from the first parameter When the message relative to the desired parameter appears press the 3 Enter key to confirm TO CHANGE THE PROGRAMMED VALUE OF THE SELECTED PARAMETER If gt appears on the second line followed by the current value Using the keyboard write the desired value or press the 1 A key to increase or the 2 key to decrease the current value Press the 3 Enter key to confirm and return to the previous point or press the 6 Esc key to exit typing without modifying the previous value Press the 4 lt key to reset the proposed number In some cases press the 4 lt key to move one digit to the left until starting again from the first on the
51. or Micro switch Y 1 Locking lever lowered product removal door Locked Y 0 Locking lever up product removal door Unlocked C Product removal door opening Micro switch K 1 Micro switch pressed product removal door Closed K 0 Micro switch not pressed product removal door Open P Parameter detected by the electronics that indicates the position of sliding panel W 1 Sliding Panel fully closed W 3 Sliding Panel partially closed W 5 Sliding Panel fully open Press the 6 key to exit the submenu Rev M 01 Pagina A 19 d am ia n Serie EUR7 rheavendors O gt VENDING SENSOR TEST FTCA Select this item to test the vending sensor circuit FTCA Eo ae D oo Ee T sens test Ee T sF The following message will appear on the display Left Nois Righ OK OK OK Left Nois Righ OK OK OK The Left and Righ parameters indicate the degree of intensity of the light detected by the sensors The Nois parameter indicates the level of intensity of the noise detected by the sensors We understand the status of the FTCA system through these three parameters Possible values OK The level is good OK The level is fair OK The level is minimal but sufficient ERR The level is insufficient If one of the three parameters should be at the ERR level the FTCA infrared system will be out of order and an OFF L10 message will be displayed see OFF message table for
52. r ahead it will automatically be rounded off and the new value will have to be reconfirmed with the 3 key Note 2 after enabling the direct selection the first price lines proposals will be 1 S2 S3 which correspond to the direct selection buttons optional Once the selling price lines have been set they can be associated with the available selections with the Price association parameter Rev M 01 Pagina A 8 d am ia n Serie EUR7 rheavendors O gt ENABLING OF THE B BRACKET SELLING PRICES Visible and programmable only with Operating mode MDB and or RFID payment system installed To activate or deactivate management of the second price line bracket B price bracket Settable values Enabled ON Disabled OFF ee Default Disabled Price ee Price B eo Current eo ue Activating management of the B selling prices it will be possible to set the prices of the second price line bracket B BRACKET SELLING PRICES Visible and programmable only with Enabling B bracket prices enabled The 44 available selling price lines of the B bracket can be set as follows EE Tm Default 2 00 for all selections Price management u ee prtces B H dki u B N u Press keys 1 and 2 to scroll through the available price lines xx going from 01 to 44 Press the 3 key to select the value VVVVV of the price line to be varied Enter the new value pressing the nu
53. r sprinkled with jets of water eae eee eet ees ees BARF C T T MIN 8 CM MIN 40 Place the vending machine in the point where it is to be installed making sure that the minimum distances shown in Figure 3 are guaranteed Also make sure that air can circulate freely in the rear and upper part the room should be ventilated regularly The vending machine must operate in a room that is in conformity with the information given in the table on page 3 Using the vending machine outside of these conditions could cause it to malfunction Adjust the height and alignment of the vending machine by means of the support feet with a 19 mm open end wrench making sure that all four of them rest correctly on the ground When the vending machine is not levelled properly it can be difficult to close the door With the wall anchoring bracket kit accessory it is possible to anchor the vending machine to the wall with two special spacers See Fig 4 as follows Screws from above Wall anchoring brackets TA Nut from inside vending Drill and fasten to wall a machine Screw the two wall anchoring brackets on the top of the vending machine see figure with the screw from above and a nut from inside the machine remove the first drawer at the top to reach the position easily Place the vending machine in the desired position and mark the position of the
54. rrect installation or maintenance wear and tear caused by excessive use maintenance operations carried out by unskilled workers transport i e caused by events not due to defects in manufacturing of the device Technical operations relative to the installation and connection of the device to the power supply systems are not included in the warranty either Damian S r l is not responsible for possible injuries and damage to persons or objects caused directly or indirectly by the lack of observance of the instructions given in this manual and of any other information transmitted by the manufacturer to the customer concerning above all the warnings cautions relative to installation use and maintenance of the device Replacement of the device and prolongation of the warranty following the occurrence of a breakdown are excluded Technical modification reservation To constantly improve the quality of our products and to guarantee an ever higher level of safety and environmental protection Damian S r l reserves the right to change the technical and construction characteristics of its own products without advance notice Damian S r l reserves the right to inform its customers through information bulletins updating of manuals communications or other information means that it considers appropriate of all of the changes regarding safety or environmental protection and all other information which turns out to be useful
55. rvised to make sure that they do not play with the vending machine Before checking any electrical part move the main switch of the vending machine See Figure 2 to the OFF position UNPACKING Unpack the vending machine as follows Cut the clear plastic wrapped around the packing box and remove the various protective corners Free the keys that are tied together with the power cord on the lower rear part of the vending machine To remove the wood supports lift the vending machine using a suitable forklift truck with a lifting capacity of at least 350 Kg and lifting height of 25 cm from the ground and remove the metal brackets blocking the vending machine s feet by removing the fixing screws ASSEMBLY OF BASE PLATE COVERING FEET There is a large package containing the base plate of the vending machine inside the machine Remove the base plate from its packaging and position it under the door in front of the feet pressing against the base of the vending machine The base plate will remain fixed to the base thanks to the magnetic hooks it comes with It is possible using 2 self tapping screws attach further the base plate to the the vending machine BASE PLATE SELF TAPPING SCREWS Rev M 01 Page 4 d am ia n Serie EUR7 rheavendors O INSTALLATION Install the vending machine in covered and protected places where it is not exposed to inclement weather and cannot be rained on o
56. scribed previously 2 select Default P Reset this message appears on the display Password 00000 3 enter the value 12345 and confirm with 3 the card will delete some of the stored programming parameters and will go automatically into self learning mode The self learning procedure occurs in the following phases Note in the event of error in any point of the procedure press the 6 key for a few seconds the self learning procedure will start over from the beginning A This message appears on the display Self learning Language Italian after selecting the desired language press to confirm B This message appears on the display Self learning Conn motors xXx Check that the number of connected motors corresponds to those actually present in the vending machine if there is a discrepancy proceed as described in the installation and service manual in the Answers to problems that might arise chapter some motors are not detected section press 3 to confirm C This message appears on the display Self learning Twin Motors OFF Press 3 if you do not wish to set twin motors in a single selection Otherwise select Twin Motors ON to set pairs of motors near each other that you wish to make run simultaneously with a single selection This message appears on the display Selection x x Current value Select the motor that you wish to set coupled and press 3 Rev M 01 Pagina A 6 d am ia n
57. ssing minutes YY Y Internal temperature 2Z Z Safety temperature by missing minutes XXX we mean the minutes within which the internal temperature YY Y must go below the safety temperature ZZ Z to prevent generation of the ERR L09 error If the ERR L09 error has been generated entering into programming you will be asked if you wish to reset the out of order by zeroing the error ERR L09 Press key 1 to reset the error 1 YES 2 NO Press key 2 to NOT reset the error IMPORTANT the values of these three parameters should be set in accordance with the current regulations applicable to the preservation of sold products See the programming parameters in Attachment A for how to set them N B To prevent false out of order indications following prolonged operator intervention it is possible to initialise the counters through the Overtemperature counter reset function Refer to Attachment A Programming Sheet Rev M 01 Page 9 damian rheavendors O Serie EUR7 ANSWERS TO PROBLEMS THAT MIGHT ARISE ERROR MESSAGES THAT APPEAR ON THE DISPLAY The following table shows the OFF messages that appear on the display when the vending machine is out of order See Figure 5 for the numerical references in parentheses Press key 1 to display further details about the type of out of order reported in the error specification in parentheses When any other key is pressed automati
58. st See programm gt diagnostics gt Sliding panel test After opening the sliding panel 10 use a brush to gently clean the LEDS 3 removing dust or dirt that might obstruct passage of the light emitted by the LEDS CHECK CLEANING OF THE REFRIGERATION UNIT CONDENSER Turn the vending machine off using the main switch access the refrigeration inspect the condenser and clean it if necessary removing any residues with a brush or suctioning blowing air Make sure that dust is not raised during these operations turn the vending machine back on only after having replaced the refrigeration unit in its normal work position Rev M 01 Page 16 d am ia n Serie EUR7 rheavendors O ENVIRONMENTAL PROTECTION Dispose of the cleaning and lubrication materials used in conformity with the regulations in force Do not dispose of the equipment with domestic waste Recycle this equipment to reduce pollution and to guarantee maximum environmental protection the materials must be recycled in conformity with local regional and state laws It is preferable to recover raw materials than to dispose of waste equipment and packing should be ecologically recycled Illegal disposal of the product by the holder involves the application of the administrative sanctions provided for by the regulations in force 1 In the European Union If the equipment is marked on the outside with this symbol it should not be disposed of with normal hous
59. the electrical box OFF L02 Temperature probe 2 error These messages indicate a problem with the probe that measures the temperature of the refrigeration unit evaporator This probe is located in the refrigeration unit located under the central plane of the machine The refrigeration unit must be removed to access the probe see specific chapter Note Probe operation is only checked at the moment the vending machine is turned on OFF L02a OFF L02b Probe 2 defective Disconnected Probe 2 disconnected error Turn the vending machine off and then on again verify in programming that the temperature value ready by probe 2 is correct and that the probe is not immersed in ice otherwise check the probe wiring and replace the probe if necessary Check the vending machine configuration to verify if this probe should be present If not carry out a new self learning procedure as indicated in the programming sheet attachment If once the probe has been replaced the problem is repeated the fault might be due to the CLP1 power board located in the electrical box Short circuit Probe 1 short circuited error Turn the vending machine off and then on again verify in programming that the temperature value read by probe 2 is correct or that the temperature of the room is not above 45 C If the error is not reset check the probe wiring and replace the probe if necessary If once the probe has be
60. the vending spiral Check the motor connections especially the correct polarity of the power supply Check that the spiral or motor are not blocked by poorly arranged products or various residues Try replacing one at a time the motor the CPU card Motor xx Time Out Error R The motor appears to work but the microswitch does not work correctly Check correct operation of the microswitch of the motor and the good condition of the motor itself Check the motor connections especially the correct polarity of the power supply Try replacing one at a time the motor the CPU card Motor xx Mot Switch Err NR The motor appears to work but functions anomalously Even if the error can be reset and the motor appears to work if this error is repeated it is advisable to replace the motor If the error is repeated even once the motor has been replaced the wiring must be checked Motor xx Max 3 Selec Err R The motor has been put out of order after three consecutive sales of the same motor without detecting that the product has dropped See FTCA Parameters chapter Check that the spiral is hooked correctly to the motor Check the operation of the product drop control sensors See Diagnostics chapter The error is automatically reset R or not reset NR upon turning on Rev M 01 Page 12 d am ia n Serie EUR7 rheavendors O UPON TURNING ON WARNING OUT OF ORDERS DETECTED
61. ually using the appropriate keys gt OUT OF ORDER MOTORS Select this item to see which motors have generated an Out of Order condition The out of orders are also listed in this menu Motor XX Out of Order o PragnostrEs i OutofOrder Mot gt gt gt f The following message will appear if there are no motors out of order No motor Out of Order If there are motors out of order you can use the 1 and 2 keys to scroll through the list of motors the current motor will be activated when the 3 key is pressed the following message will appear if there is still a malfunction Error XXXXXX Where xxxxxx is the detected error See the Installation and service manual Problems and relative solutions chapter Motor anomaly messages section for the list of anomalies and relative solutions It is important to keep in mind that even possible out of orders that are automatically reset R by turning the vending machine on and off are also listed in this menu see Motor anomaly messages chapter indicated above The indication remains until the out of order has been reset as indicated below Press the 4 key to cancel the Out of Service condition of the current motor The following message will appear on the display Motor 3 KX Reset Press the 6 key to exit the submenu NOTE It is possible to cancel all of the Out of Order conditions of the motors without entering into programming by pressing the PS
62. ue MAXIMUM 3 FTCA SELECTIONS In the case of a missed sale allows making up to a maximum of 3 other selections without losing the credit Settable values Disabled OFF Enabled ON D efault Enabled nra ey FTCA es Ea Si Max 3 FTCA Selec Current value IMPORTANT When this parameter is enabled at the third consecutive sale of the same selection without detecting the product drop the motor is put out of order and the credit deducted gt DECIMAL POINT Sets the position of the decimal point on the display used to indicate prices with parts in cents the value 1 corresponds to 1 decimal 0000 0 Settable values 0 3 os Default 2 os param Decimal oe Current oe ue Rev M 01 Pagina A 5 d am ia n Serie EUR7 rheavendors O gt CODE MODE Allows to read the internal parameter software code mode eae Read only Current value gt VISUALISATION OF THE SW VERSIONS INSTALLED To visualise the software versions installed Programming General param f p Software vers gt gt gt Press keys 1 and 2 to scroll through the versions of the various softwares gt CARD REINITIALISATION To reinitialise the vending machine s CPU card for example after replacement with a new unprogrammed one ceneral param Default P Reset gt gt gt Proceed as follows to reinitialise the card 1 enter into programming General parameters as de
63. ure for the Food zone Drink amp Snack disables management of the safety temperature for the Food zone OFF disables operation of the refrigeration unit gt FTCA PARAMETERS The series EUR7 vending machines can have an infrared system installed on the sides of the pick up tray for detecting actual passage of the product Sale has occurred This infrared system comprises a pair of infrared LED barriers which during normal operation are protected hidden by the sliding anti theft panel which is closed At each sale the FTCA barriers check the actual passage of the product if it is not detected Missed Sale the vending machine maintains the credit and if the Enable 3 step mode is active it attempts to make the spiral turn again by about 1 4 turn repeating the operation 3 consecutive times If these attempts also fail or if the 3 step function is not active the vending machine still keeps the credit stored in memory and allows a new selection to be made When this function is selected it will be possible to set the following parameters of the FTCA function ENABLING FTCA VENDING SENSORS To activate operation of the vending sensors that check passage of the product Settable values 0 Disabled FTCA deactivated 1 Enable NoStep FTCA activated 2 Enable 3Step FTCA activated 1 4 turn management Default 2 Enable 3Step pera FTCA loa ae loa ae eas FTCA enabling Current val

Download Pdf Manuals

Related Search

INSTALLATION AND SERVICE PROGRAMMING installation service program installation service program template how to install service the installation of services use /install to install service computer programming installation guide standard installation of the program free installation and service install and install program software installation and maintenance service-install service programming system download installation and repair services installation repair and maintenance service panel installation code installation and activation service a software installation guide church installation service program service and installation rules a program required for this install industrial service and installation pastor installation service program pdf pastor installation service program

Related Contents

Burger de poulet brie - La Boucherie Beauce Boeuf  デジタル式乳房X線撮影装置及び保守仕様書  User manual - Interfocos  INSTALLATION MANUAL MANUEL D  Collection  User`s Manual - Reliability Direct, Inc.  ce lien  Singulair Green Owner Manual  English & Español  LE MANUEL D`UTILISATION  

Copyright © All rights reserved.