VAG CODE READER AND RESET TOOL EOBD & GENERIC
Contents
1. have been shown up detected will be observed on the upper right hand corner of the display Select Function 1 Read Codes gt 2 Erase Codes 3 ECU Information 4 Readiness Test Erasing Codes CAUTION Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle s on board computer but also Freeze Frame data and manufacturer specific enhanced data Further the I M Readiness Monitor Status for all vehicle monitors is reset to Fail status Do not erase the codes before the system has been checked completely by a technician 1 If you decide to erase the DTCs use the UP DOWN scroll buttons to select Erase Codes from the Select Function menu and press the Y button O If the scan tool is not connected or no communication is established with the vehicle yet then refer to Reading Codes 1 to 7 Erase Codes Erase Trouble Codes Are you sure lt YES gt NO 2 A warning message comes up asking for your confirmation 3 If you do not want to proceed with erasing the codes press the N button to exit A message of command cancelled will show up 4 If you do wish to proceed to erase the codes then press the Y button 5 If the codes are cleared successfully an ERASE DONE confirmation message will show on the display Press any button to return to the previous menus 6 If the codes are not cleared then an ERASE FAILURE message will appear Press the N button to return2. scan tool to communicate with the vehicle Contact your local distributor or the manufacturer s customer service department for assistance After the vehicle protocol is displayed on the screen press any key or wait about 2 seconds for the OBDII EOBD Diag menu to come up Use the UP DOWN scroll buttons to select Read Codes from the menu and press the Y button If there are no Diagnostic Trouble Codes present the display will indicate NO CODES ARE STORED IN THE MODULE If there are any Diagnostic Trouble Codes present the Fault Codes and Pending Codes will be reported on the display OBDII EOBD Diag gt 1 Read Codes 2 Erase Codes Erasing Codes 1 wn If you decide to erase the DTCs use the UP DOWN scroll buttons to select Erase Codes from the OBDII EOBD Diag menu and press the Y button If the scan tool is not connected or no communication is established with the vehicle yet then refer to Reading Codes from 1 to 8 Erase Codes Erase Trouble Codes Are you sure lt YES gt NO A warning message comes up asking for your confirmation If you do not want to proceed with erasing the codes press the N button to exit A message of command cancelled will show up If you do wish to proceed to erase the codes then press the Y button If the codes are cleared successfully an ERASE DONE confirmation will show on the display Press any button to return to previous menus If the codes are not cleared
3. then an ERASE FAILURE message will appear Press the N button to return to previous menus Main Menu 1 VW AUDI 2 OBDH EOBD gt 3 Oil Reset 4 System Setup Oil Reset AON o Turn the ignition off Locate the vehicle s 16 pin Data Link Connector DLC Plug into the scan tool cable connector to the vehicle s DLC Turn the ignition on But do not start the engine Press the Y button The Main Menu will be observed on the display Use the UP DOWN scroll buttons to select Oil Reset from the menu Press the Y button to accept the option and to move to the next screen 10 Vehicle Make gt 1 VW AUDI 2 AUDI 3 SEAT 4 SKODA Do the following to select menu options Use the UP DOWN scroll buttons to move the cursor and select an option Press the Y button to accept the option and to move to the next screen Repeat a and b to select the necessary options Follow any on screen instructions Optionally use the N button to return to previous screens If the Service Reset Failed message appears then there might be problems for the scan tool to communicate with the vehicle being tested Refer to the vehicle service manual for more information When done turn off the ignition and disconnect the scan tool NOTE It is our policy to continually improve products and as such we reserve the right to alter data specifications and component parts without prior notice IMPORTANT No liability is accepte
4. to previous menus Select Function 1 Read Code 2 Erase Code gt 3 ECU Information 4 Readiness Test Viewing ECU Information 1 To view ECU Information use the UP DOWN scroll buttons to select ECU Information from the Select Function menu and press the Y button Select Function 1 Read Code 2 Erase Code 3 ECU Information gt 4 Readiness Test Readiness Test Important The Readiness Test function is used to check the operations of the Emission System on OBD2 EOBD compliant vehicles It is an excellent function to use prior to having a vehicle inspected for compliance to an emissions program O Pass Indicates that a particular monitor being checked has completed its diagnostic testing O Fail Indicates that a particular monitor being checked has not completed its diagnostic testing or the monitor is not supported on that vehicle 1 Use the UP DOWN scroll buttons to select Readiness Test from the Select Function menu and press the Y button O If the scan tool is not connected yet then refer to Reading Codes 1 to 7 ECU Information VAG No 06A906032TF Component Bosch 1L 815VT 0020 Coding 0008570 Imp 0000 WSC 000078 O If the scan tool is not connected or no communication is established with the vehicle yet then refer to Reading Codes 1 to 7 O If there is no ECU Information available a warning message shows on the display 2 Press the N button to return to previous
5. which is not included in this product package Part No VS8X01 VS862 1 040107 4 SETUP Navigation Characters Characters used to help navigate the scan tool are gt Indicates current selection J A flashing Down Arrow indicates additional information is available on the next screen A flashing UP Arrow indicates additional information is available on the previous screen Pd Identifying a Pending DTC when viewing DTCs Power The external power of the scan tool is provided via the vehicle Data Link Connector DLC Just follow the steps below to turn on the scan tool 1 Connect the OBD I Cable to scan tool 2 Find DLC on vehicle 3 A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the RJ1966 connector 4 Plug RJ1966 Cable to the vehicle s DLC The scan tool allows you to make the following adjustments and settings 1 Contrast adjustment Adjusts the contrast of the LCD display 2 Display Test Tests the LCD display 3 Keyboard test Tests the keyboard System Setup Main Menu gt 1 Contrast 2 Display Test 3 Keyboard Test 1 VW AUDI 2 OBDII EOBD 3 Oil Reset gt 4 System Setup To enter the setup menu mode 2 From the Main Menu Use the UP DOWN Scroll Buttons to 1 From the keyboard Press and hold the N button for at least 3 select System Setup and then press the Y button Follow the seconds until the System Setup menu shows Follow the in
6. Profesore INSTRUCTIONS FOR DLAN At CULCEAILULS 4 o ns VAG CODE READER AND RESET TOOL EOBD amp GENERIC Model VS862 Thank you for purchasing a Sealey Product Manufactured to a high standard this product will if used according to these instructions and properly maintained give you years of trouble free performance IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY NOTE THE SAFE OPERATIONAL REQUIREMENTS WARNINGS AND CAUTIONS USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED FAILURE TO DO SO MAY CAUSE DAMAGE AND OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE 1 SAFETY INSTRUCTIONS WARNING Ensure that Health and Safety local authority and general workshop practice regulations are strictly adhered to DO NOT use the unit if it or any attachment is damaged Maintain the unit in good and clean condition for best and safest performance If required ensure that the vehicle to be worked on is adequately supported with axle stands or ramps and is chocked Put transmission in PARK for automatic transmission or NEUTRAL for manual transmission and make sure the parking brake is engaged Wear approved eye protection A full range of personal safety equipment is available from your Sealey dealer Wear suitable clothing to avoid snagging Do not wear jewellery and tie back long hair WARNING Use extreme caution when working around the ignit
7. ROR message shows up on the display Verify that the ignition is ON Check if the scan tool s OBD II connector is securely connected to the vehicle s DLC Verify that the vehicle is OBDII EOBD compliant Turn the ignition off and wait for about 10 seconds Turn the ignition back to on and repeat the procedure from step 5 P0118 Pd 1SO9141 Pressure Control Solenoid A Control Circuit Low The DTC number will appear on the upper left hand corner and its definition will show on the body of screen The type of code Generic or Manufacturer specific the vehicle protocol the sequence of the DTC currently being observed the total number of codes detected and the module ID will be observed on the upper right hand corner of the display If the code being displayed is a pending code the Pd icon will be observed next to the DTC number on the upper right hand corner of the display When a DTC s definition covers more than one display screen use the Y button as necessary to view any additional information If the retrieved DTCs contain any manufacturer specific or enhanced codes you will be prompted to refer to the vehicle service manual to view the DTC definitions If more than one DTC is found use the UP DOWN scroll buttons as necessary until all the codes have been shown up OBDII EOBD Diag gt 1 Read Codes 2 Erase Codes If the LINK ERROR message does not go away then there might be problems for the
8. at the keys are functioning name should be observed on the display If the name does not properly show up then the key is not functioning properly 1 Use the UP DOWN scroll buttons to select Keyboard Test from 3 Double press N to return to the previous menu the System Setup menu and then press the Y button 5 OPERATION Main Menu A Select System gt 1 VW AUDI 2 OBDI EOBD 3 Oil Reset 4 System Setup 02 Auto Trans 15 Airbags 03 ABS Brakes 08 Auto HVAC 09 Cent Elect VAG Diagnostics 7 Use the UP DOWN scroll buttons to select the system from the Select System menu and press the Y button If the scan tool fails to communicate with the selected vehicle s ECU Electronic Control Unit a LINK ERROR message shows up on the display Verify that the ignition is ON Check if the scan tool s OBD II connector is securely connected to the vehicle s DLC Verify that the module is supported Turn the ignition off and wait for about 10 seconds Turn the ignition back to on and repeat the procedure from step 5 If the LINK ERROR message does not go away then there might be problems for the scan tool to communicate with the module being tested The most common cause is that the scanned module is not supported on the vehicle O The numbers 01 02 15 03 08 etc in front of the system names refer to the physcal addresses assigned to the systems not the sequence of the systems to be arranged Reading C
9. d for incorrect use of product WARRANTY Guarantee is 12 months from purchase date proof of which will be required for any claim JHM Butt amp Co Ltd Tel 01302 710868 Fax 01302 719481 www jhmbuttco com info jhmbuttco com
10. ion coil distributor cap ignition wires and spark plugs These components create hazardous voltages when the engine is running DO NOT connect or disconnect any test equipment with ignition on or engine running Keep a fire extinguisher suitable for gasoline chemical electrical fires nearby Account for all tools and parts being used and do not leave them on or near the engine Keep code reader dry clean and free from oil water and grease Use a mild detergent on a clean cloth to clean the outside of the tool Operate the vehicle in a well ventilated work area exhaust gases are poisonous IMPORTANT Always refer to the vehicle manufacturer s service instructions or a proprietory manual to establish the current procedure and data These instructions are provided as a guide only ON SS86 O SAK 2 SPECIFICATION amp ACCESSORIES Display Backlit 128 x 64 pixel display with contrast adjustment Operating Temperature 0 to 50 C 32 to 122 F Storage Temperature 20 to 70 C 4 to 158 F External Power 8 0 to 15 0 Volts provided via vehicle battery Accessories Included User s Manual Instructions on tool operations OBD2 cable Provides power to tool and communicates between tool and vehicle Serial Cable Used to upgrade the scan tool Carry Case A nylon case to store the scan tool when not in use Fig 1 Reference 1 LCD DISPLAY Indicates test results 2 Y BUTTON Confirms a selection or action from a men
11. menus Readiness Test EGR Sys Heated O2 O2 Sensor s A C Sec Air Inject EVAP Sys N Use the UP DOWN scroll buttons as necessary to view the status of the following monitors Misfire Monitor Fuel Sys Fuel System Monitor CCM Comprehensive Components Monitor EGR Sys EGR System Monitor O2 Sensor s O2 Sensors Monitor Catalyst Catalyst Monitor EVAP Sys Evaporative System Monitor Heated O2 O2 Sensor Heater Monitor Sec Air Inject Secondary Air Monitor A C A C System Monitor Catalytic Conv Catalytic Convertor Monitor Press the N button to return to previous menus v AAAA A A Main Menu 1 VW AUDI gt 2 OBDH EOBD 3 Oil Reset 4 System Setup OBDII EOBD Diagnostics Reading Codes CAUTION Don t connect or disconnect any test equipment with ignition on or engine running o akhwhnd QO KK KK 10 Turn the ignition off Locate the vehicle s 16 pin Data Link Connector DLC Plug into the scan tool cable connector to the vehicle s DLC Turn the ignition on But do not start the engine Press the Y button The Main Menu will be observed on the display Use the UP DOWN scroll buttons to select OBDII EOBD from the menu Press the Y button A sequence of messages showing the OBDII EOBD protocols will be observed on the display until the vehicle protocol is detected If the scan tool fails to communicate with the vehicle s ECU Engine Control Unit a LINK ER
12. odes CAUTION Don t connect or disconnect any test equipment with ignition on or engine running 1 Turn the ignition off 2 Locate the vehicle s 16 pin Data Link Connector DLC 3 Plug into the scan tool cable connector to the vehicle s DLC 4 Turn the ignition on But do not start the engine 5 Press the Y button The Main Menu will be observed on the display 6 Use the UP DOWN scroll buttons to select VW AUDI from the menu and press the Y button MO SSO SS Select Function 16627 100 gt 1 Read Codes 2 Erase Codes Solenoid Valve A 3 ECU Information For Boost Pressure 4 Readiness Test Control N75 Malfunction P0243 8 Select Read Codes from the Select Funciton menu and press O When a DTC s definition covers more than one display screen the Y button use the Y button as necessary to view any additional O If there are no Diagnostic Trouble Codes present the display information will indicate NO CODES ARE STORED IN THE MODULE 1 If the DTC definition is not available an advisory message If there are any Diagnostic Trouble Codes present the DTC prompting you to refer to the vehicle service manual will be number and its definition will show on the LCD display observed on the display The subcode the communication protocol the sequence of the If more than one DTC is found use the UP DOWN scroll DTC currently being observed and the total number of codes buttons as necessary until all the codes
13. structions to make adjustments and settings as described in instructions to make adjustments and settings as described in the following setup options the following setup options System Setup gt 1 Contrast 2 Display Test 3 Keyboard Test System Setup gt 1 Contrast 2 Display Test 3 Keyboard Test Contrast Adjustment 2 From the Contrast menu use the UP DOWN scroll buttons 1 From the System Setup menu use the UP DOWN scroll to decrease or increase the contrast buttons to select Contrast and press the Y button 3 Press the Y button to save your selection and return to previous menu 4 Press the N button to return to previous menus Display Test Press Y to test Look for missing System Setup 1 Contrast gt 2 Display Test 3 Keyboard Test spots in characters Press lt N gt to return Display Test 2 Press the Y button again to start test Look for missing spots in The Display Test is used to check the LCD display the solid black characters 1 From the System Setup menu use the UP DOWN scroll 3 When completed press the N button to return buttons to select Display Test and press the Y button VS862 1 040107 J System Setup p Keyboard Test 1 Contrast Press any key to 2 Display Test gt 3 Keyboard Test Start test to display name Key Double N to Return Keyboard Test 2 Press any key to start test When you press a key the key The Keyboard Test is used to verify th
14. u When a DTC s definition covers more than one screen it is used to move down to the next screen for additional data 3 N BUTTON Cancels a selection or action from a menu or returns to the menu It is also used to set up the unit when pressed and held for at least 3 sec 4 UP SCROLL BUTTON Moves up through menu and submenu items in menu mode When more than one DTC is retrieved moves up through the current screen to the previous screens for additional DTCs and definitions 5 DOWN SCROLL BUTTON Moves down through menu and submenu items in menu mode When more than one DTC is retrieved moves down through the current screen to the next screens for additional DTCs and definitions 6 OBD II CONNECTOR Connects the scan tool to the vehicle s Data Link Connector DLC 3 VEHICLE APPLICATIONS Vehicle Coverage Audi Seat Skoda VW Beetle Golf GTI Jetta Passat Toureg The VS862 Code Reader and Reset Tool is specially designed to work with most VAG vehicles sold Worldwide from 1990 on If a VAG has a 16 pin RJ1966 Data Link Connector DLC the code reader will work If it has an old style 2x2 Data Link Connector DLC then it depends on whether there are 4 or 3 wires connecting to the pins If there are 4 wires each connecting a pin then it will work If there are only 3 wires leaving one pin disconnected then it will not work For VAG with old style 2x2 Data Link Connector DLC you need to have a 2x2 cabling adapter
Download Pdf Manuals
Related Search
VAG CODE READER AND RESET TOOL EOBD laser eobd code reader/reset tool obd2 eobd code reader manual laser obdii/eobd code reader \u0026 reset tool obd2 eobd code reader obdii eobd code reader manual what is eobd code reader how to use obdii/eobd code reader vag fault code reader obd11 eobd code reader eod_reset obdii code reader and reset tool code reader obd ii reset can obd11 code reader eobd scanner