Home

Owners Manual

1. is low Add oil and restart Engine Switch The engine switch controls the ignition system ON A A Ignition circuit is switched on STOP The engine can be started RR O B Ignition circuit is switched off B The engine will not run BD DC Protector The DC Protector turns of automatically when the loads exceeds the generator rated output 1 min ON OFF PUSH PROTECTOR Note If the DC Protector trips to the OFF position press to reset Reduce the load to the specified generator output if the DC protector turns off If it turns off again consult the authorized dealer page 6 Genquip Gi3300 DSP Inverter Generator Operation Starting The Engine Note Before starting the engine do not connect any electric devices 1 Turn the fuel switch lever to the ON position 2 Turn the engine switch to the ON position Note Sometimes the choke is required to start a warm engine 3 Hold the choke knob fully out 4 Pull slowly on the recoil starter until it is engaged then pull it briskly 5 After the engine starts warm up the engine until the engine does not stop when the choke knob is returned to the original position 6 Push the choke knob back to the original position Note When starting in cold conditions below 5 C run the engine with choke applied for two to three minutes to warm up
2. exhaust can cause may be damaged due to close to dissipate freely proximity Smoking around the Fire Explosion 2 Do not smoke around generator Serious Injury the generator under any circumstances Operating whilst Electrocutionasdfa 1 Never operate the generator wet or Cleaning the whilst wet or expose to generator when in damp conditions Clean the operation can cause generator only when shut down and cooled down completely Do not spray water directly on or near any electrical items Use a damp cloth to Wipe over generator to keep clean Operating generator Engine to seize and over heat 2 Always operate generator on a on an uneven surface due to improper lubrication level amp hard surface may cause Fuel spillage which may cause fire or explosion resulting in serious injury Moving the generator Fuel spillage which may 2 Always shut down generator whilst in operation cause fire or explosion and allow it to cool completely resulting in serious injury before moving Transporting Fuel spillage which may 2 Ensure fuel tap is switched generator cause fire or explosion off and the fuel cap is affixed resulting in serious injury Oil firmly Always transport spillage which may cause the generator in an upright slippage position If transporting over a long distance drain fuel from tanks Using the incorrect Misfiring of engine which 2 Ensure you check that you fuel amp or oil type may result in engine parts separa
3. NGLE CYLINDER 66mm X 50mm CDI BPR4ES NGK F7RTC 0 8 0 028 0 031 inches 1L71 e 4 9HP at 3600 r min Unleaded Petrol 600 ml page 18 Genquip Gi3300 DSP Inverter Generator Wiring Diagram 2 m m SiE seine SD ov gS Fi R DB R GIy z gt HNO e G Y HY pi L po t SS ae 5 SREY BN Br Wit pwe a REY RPTL SI ex Tw Is ol F BI as er ren u T l D U B W r j e Color code B Black 1 Main coil 13 Ignition coil Br Brown 2 Sub coil 14 Spark plug G Green 3 Control unit 15 AC CDI unit L Blue 20 AC indicator light 16 Pulsar coil O Orange 5 AC receptacle 17 Stepping motor R Red 6 Ground Earth terminal 18 Charge coil W White 7 Economy Control Switch 19 DC receptacle Y Yellow 8 Accelerator controller 20 Overload indicator light P Pink 9 Engine switch 21 Ballast B W Black White G Y Green Yellow W L White Blue 10 Oil w
4. Ower GAUP 7 Genquip Gi3300 DSP Inverter Generator Owners Manual Genquip Gi3300 DSP Inverter Generator page 1 page 2 Genquip Gi3300 DSP Inverter Generator Table of Contents Control Function 4 Air Filter Maintainence 11 Pre Operation Checklist 5 Valve Adjustment 12 e Fuel System e Refueling amp Fuel Level Gauge Senauipealey ee e Engine Oil Operating Procedure 16 Control Function Continued 6 on art Up e Qil Warning System e Shutdown e Engine Switch e DC Protector Maintaining your Generator 17 Operation 7 a Cleaning e Storing or Transporting Starting The Engine e Servicing Periodic Maintenance 8 Specifications amp Dimentions 18 Spark Plug Inspection amp Wiring Diagram 19 Oil Replacement 9 Troubleshooting 20 21 Engine Oil Replacement 10 e Engine Won t Start Generator Won t Produce Power Fuel Filt 1 nn e Storage Drain The Fuel Fuel Tank Filter 11 e Storage Engine Warranty 22 Notes 23 Genquip Gi3300 DSP Inverter Generator page 3 Control Function z TECH es 12 Description and Control Panel Key Carrying Handles Fuel Level Gauge Fuel Cap and Vent Fuel On Off Switch AC Ready Pilot Light Oil Warning Light Ground Earth Terminal 240 Volt Sockets Engine On Off Switch 10 Choke Knob 11 Recoil Sta
5. a level surface Never refuel your Genquip generator whilst the engine is running Always allow sufficient time for the generator to cool down before refueling Always refuel the generator in a well ventilated area Keep all flammable materials and fuel away from the operating generator Caution of the hot exhaust must be observed as a generator can easily start a fire always locates your generator where its exhaust will vent safely Avoid getting burned Many generator parts radiate heat that is sufficient to burn you during operation Only a licensed electrician should hard wire your Genquip generator Turn off all equipment powered by the generator before shutting down your generator Never over load your Genquip Generator if unsure about the power requirements consult a licensed electrician Generators can be noisy so when working around the generator it may be advisable to wear appropriate ear protection Keep children away from your Genquip generator at all times Never permit anyone to operate a Genquip generator without proper instructions DANGER Only competent and qualified electricians should connect wiring to this equipment all connections must comply with all applicable Australian Standards and electrical codes Genquip Gi3300 DSP Inverter Generator page 13 Activity Procedure Potential Hazards Risk Corrective Action If you do this This could happen You can preve
6. arning light 11 Oil warning unit 12 Oil level gauge Genquip Gi3300 DSP Inverter Generator page 19 Troubleshooting Engine Won t Start Carefully inspect the generator set before you first use it look for the following discrepancies 1 Fuel system engine is not getting fuel e No fuel in tank Supply fuel Clogged fuel line Clean fuel line e Foreign matter in fuel filter Replace fuel filter e Clogged carburetor Clean carburetor 2 Engine oil light flashes e Oil level is low Add engine oil 3 Electrical system e Engine switch to ON Poor or no spark e Spark plug is dirty Replace sparkplug e Faulty ignition system Consult dealer 4 Compression Insufficient e Worn out piston and cylinder Consult dealer Generator Won t Produce Power Stop the engine then restart If A C lights continue to flash consult your dealer Storage Long term storage of your machine will require some preventive procedures to guard against deterioration Drain The Fuel 1 Remove the fuel tank cap Drain the fuel tank into an approved gasoline container using a commercially available hand siphon Then install the fuel tank cap WARNING Fuel is highly flammable and poisonous Wipe up any spilled fuel immediately 2 Drain fuel from the carburetor by loosening the drain screw on the carburetor float chamber 3 Turn the fuel cock lever to OFF Start the engine and leave it run until it stop
7. ator page 11 Valve Adjustment Note Valve adjustment should only be performed on a cool engine 1 Remove back case then take off valve cover 2 Pull the starter rope gently and set the piston in top dead center Use a stick in the spark plug hole measure the depth 3 Insert a feeler gauge into the gap between rocker and valve to measure the valve clearance Valve Clearance Intake 0 1mm 0 004 in Exhaust 0 1mm 0 004in 4 If adjustment is necessary proceed as follows a Hold rocker axis using the wrench and loosen the lock nut b Loosen the lock nut of rocker axis to gain the specified intake and exhaust valve clearance c Hold rocker axis using a wrench and tighten the lock nut d Check the clearance of valve after adjustment page 12 Genquip Gi3300 DSP Inverter Generator Genquip Safety Genquip values your safety and the safety of others when using your Genquip generator General safety It is important to read and understand your owner s manual before operating your Genquip generator Safety tips for safe operation Know where the controls are and how they operate for the startup and shut off procedure Know the location of the fuel shutoff and how it operates Genquip generators must always be used in a well ventilated area Your Genquip generator is not weatherproof To prevent electrical shock make sure your generator is properly grounded Operate the generator on
8. he oil filler cover as shown and remove the oil filler cap so that the oil can be completely drained 5 Check the drain bolt gasket oil filler gap and O ring 6 Reinstall the oil drain bolt Drain Bolt Torque 12 Ft Ibs 7 Add engine oil to the upper level e Recommended oil for most climastes 10W30 e Engine Oil Quantity 600 millilitres CAUTION Be sure no foreign material enters the crankcase 8 Install the oil filler cap 9 Install the rubber cap on the bottom CAUTION Be sure to install securely to prevent from falling off during operation 10 Close the oil filler cover 17 we ee mE TE ae aa page 10 Genquip Gi3300 DSP Inverter Generator Fuel Filter Do not smoke or have an open flame in the vicinity of the fuel and solvent 1 Stop the engine 2 Clamp the fuel line with the clip 3 Replace the fuel filter Fuel Tank Filter 1 Remove the fuel tank cap and filter 2 Clean the filter with solvent if damaged replace 3 Wipe the filter and insert it WARNING Be sure the tank cap is securely tightened Air Filter Maintainence 1 Remove black side cover 4 screws opposite exhaust outlet side Unscrew bolts Remove cover Remove foam air filter Ole Zu gt Clean filter in foam filter cleaner and dry Re oil with filter oil 7 Squeeze out excess oil Do not wring out 8 Reitto machine and reassemble Genquip Gi3300 DSP Inverter Gener
9. motor Genquip Gi3300 DSP Inverter Generator page 7 ee S SER Periodic EEE S KP LS Maintenance wT Ps Se S L amp S w NX S w Item Attention ae a 1 Clean Adjust Spank LE 2 Replace 1 2 Valve Clearance Check Adjust Vv ere 1 Check A E Engine Oil arae il 2 2 i 1 Check Air Cleaner 2 Replace 11 1 2 Fuel Filter Replace v Clean Spark v Arrester Screen Recoil Starter Check operation Vv Choke Handle Check operation Y Check hose condition Fuel System look for leaks A A Fittings Fasteners Check and Tighten Y iY Cooling System Air Check for obstructions v Y Exhaust System Check for obstructions Y First 20 hours amp then every 50 hours page 8 Genquip Gi3300 DSP Inverter Generator Spark Plug Inspection amp Oil Replacement You should periodically remove and inspect the spark plug 1 Check for discoloration and remove the carbon 2 Check the spark plug type and gap e Standard electrode color Tan Color e Standard Spark Plug BPR4ES NGK F7RTC e Gap 0 028 0 031 inches 3 Install the spark plug e Spark Plug Torque 14 Ibs Ft Genquip Gi3300 DSP Inverter Generator page 9 Engine Oil Replacement 1 Place the machine on a level surface and warm up the engine Then stop the engine 2 Remove the rubber cap on the bottom Place an oil pan under the engine Remove the drain bolt 4 Open t
10. nt by Operating generator in Generator may over heat 2 Operate generator in a unventilated or enclosed Carbon Monoxide CO 1 well ventilated area Do area poisoning from the toxic not operate in an enclosed engine exhaust location Operate the generator Unsafe operation could 2 Review and understand all in a careless reckless lead to serious injUry to the operating instructions manner you amp others and warnings supplied by manufacture Refueling the generator Petrol vapors are highly 2 Always shut down engine while engine IS running flammable amp could cause and allow engine to cool a fire or explosion which sufficiently Open fuel can cause serious injury cap slowly and have an appropriate fire extinguisher present Over filling with fuel Fuel that is spilled whilst 2 Open fuel cap slowly Do or fuel spillage while refueling can cause fire not over fill fuel tank If refueling or explosion fuel spillage has occurred during refueling clean the spillage completely and allow sufficient time for any fuel vapors to dissipate Tampering with the Generator could over heat 2 Never attempt to tamper with factory preset engine and engine could over factory settings if in doubt settings speed which may result contact Genquip in a fire causing injury Failure to use the Generator unit could 1 Make sure the generator generator grounding point become electrically is connected grounded and correctly ground the charged and could cause c
11. orrectly generator electrocution Exceeding the load Could overheat some 1 Understand load ratings capacity of the generator items or their attached 2 Make sure that the total by attaching to many wiring causing fire or of electrical loads for all items or items with very electrical shock attachments does not high load ratings exceed the load rating of the generator Refer to a licensed electrician if in doubt Operating generator Exposed moving parts 2 Never operate the generator with guards or protective covers removed and hot surfaces could Cause injury without the factory fitted guards or protective covers page 14 Genquip Gi3300 DSP Inverter Generator Activity Procedure Potential Hazards Risk Corrective Action If you do this This could happen You can prevent by Contact with hot Could result in serious burns 2 During operation touch only surfaces such as the control surfaces Shutting engine exhaust the generator down and components etting it cool sufficiently Keep children away from generator during and immediately after operation Operating generator Heat buildup that could 2 Ensure that the generator to close to buildings cause generator to overheat is sufficient distance from or placing objects and the possibility of fire buildings or objects allowing close to the muffler Objects close to generator heat and exhaust emissions
12. rter O ONAN Pw mNn page 4 Genquip Gi3300 DSP Inverter Generator Pre Operation Checklist Note Pre operation checks should be made each time the generator is used Fuel System Make sure there is sufficient fuel in the tank The engine must use regular unleaded petrol only and the fuel tank capacity is 7 litres Refueling And Fuel Level Gauge To refuel remove cap and fuel slowly until fuel gauge indicates full Apply fuel cap and turn fuel vent to the ON position Fuel Cap and Vent Er eo EJ Fuel Level Gauge _ Oe uw F Full Mie WARNING Fuelis high flammable and poisonous DO NOT fill above the top of fuel filler or it may overflow when the fuel heats up and expands Wipe up any spilled fuel immediately After refueling make sure the tank cap is tightened Engine Oil Make sure the engine oil is at the upper level of the oil filler hole Add oil as necessary Recommended oil for most climates is 10W30 Engine oil quantity is 600 millilitres Genquip Gi3300 DSP Inverter Generator page 5 Control Function Continued Oil Warning System If the oil level falls below the safe operating level the engine will stop automatically Unless you refill with oil the engine will not start again Note If the engine stalls or does not start turn the engine switch to ON position and then pull the recoil starter If the oil warning light flickers for a few seconds the engine oil
13. s This will burn any remaining fuel in the carburetor page 20 Genquip Gi3300 DSP Inverter Generator Engine 1 Remove the spark plug pour about one tablespoon of SAE 10W30 or 20W40 motor oil into the spark plug hole and reinstall the spark plug Turn over engine several times with ignition off to coat the cylinder walls with oil 2 Pull the recoil starter until you feel compression The stop pulling This prevents the cylinder and valves from rusting 3 Clean exterior of the generator 4 Store the generator in a dry well ventilated place with the cover placed over it 5 The generator must remain in a vertical position when stored carried or operated Genquip Gi3300 DSP Inverter Generator page 21 Notes Genquip Gi3300 DSP Inverter Generator page 23 www genquip com au Genquip Warehouse 45 Riverside Road Chipping Norton NSW Call 1300 730 716 page 24 Genquip Gi3300 DSP Inverter Generator
14. the unit use dry filtered low pressure air or vacuum system CAUTION DO NOT use a forceful spray of water to clean the generator Water can penetrate generator s electrical system which could reduce insulation resistance Possible generator failure may result Storing or Transporting Turn fuel tap off Storage Petrol models drain carburetor and fuel tank Servicing First service 20 hours Service intervals thereafter 50 hours If operating in hot dusty conditions oil and air filters must be checked daily and service intervals should be every 10 hours initially and every 25 hours thereafter Genquip Gi3300 DSP Inverter Generator page 17 Specifications amp Dimentions GENERAL OVERALL LENGTH 585mm OVERALL WIDTH 420mm OVERALL HEIGHT 470mm DRY WEIGHT 30 kg GROSS WEIGHT 32 kg FUEL TANK CAPACITY 7 litres NOISE LEVEL 53 58 dB at 7 metres GENERATOR TYPE AC OUTPUT Multistage permanent magnet generator RATED OUTPUT 3000 Watts MAX OUTPUT 3300 Watts FULL TANK OUTPUT 13500 Watts RUN TIME AT 1 2 RATED LOAD 8 5 hours RUN TIME AT RATED LOAD 4 5 hours POWER CONVERSION RATE 85 92 RATED VOLTAGE 240 V RATED FREQUENCY 50 Hz RATED CURRENT 13A DC OUTPUT 12V 8A ENGINE TYPE 166F OHV AIR COOLED STARTING SYSTEM CYLINDER ARRANGEMENT BORE X STROKE IGNITION SYSTEM SPARK PLUG TYPE GAP DISPLACEMENT RATED OUTPUT FUEL ENGINE OIL QUANTITY 4 STROKE RECOIL START INCLINED SI
15. ting from main body resulting in serious injury are using correct oil and fuel types Genquip Gi3300 DSP Inverter Generator page 15 Genquip Operating Procedure Visual Inspection Carefully inspect the generator set before you first use it look for the following discrepancies e General appearance and cleanliness e Loose or broken wires and defective connections o oil or fuel pooling around generator e Check fuel filter e Missing covers e Oil level e Fuel level e Air filter is not dusted and is free of debris e Generator grounded e Fuel cap on Start up e Disconnect any electrical devices from the generator e Generator is on a level surface e Exhaust is free from obstructions e Fuel shut tap is on e Always use fresh fuel e Engine switch is in the on position e Choke is in the open position e Return choke to the closed position once running petrol model only Shutdown e Make sure all electrical devices are disconnected from generator e Turn the fuel tap to the off position e Allow the generator to cool sufficiently before moving or storing page 16 Genquip Gi3300 DSP Inverter Generator Maintaining your Generator Cleaning Keep the generator set clean and free of foreign material Clean generator at least once monthly A soft brush may be used to loosen caked on dirt Use a soft damp cloth to wipe away loosened dirt To clean dirt from hidden or remote areas of

Owners Manual

Contents

Download Pdf Manuals

Related Search

Related Contents