Home

Troubleshooting - SD Fire Alarms

1. main unit for the system 2 Enter your PIN code and then press the Yale button 3 The LED will flash in the sequence green Orange red 4 The unit is now in sending mode for the next 2 minutes The green and orange LED will flash every second 5 Hold the rear metal contact points of the main unit against the eyebrow contact points of the learner unit to which you are pairing 6 To confirm the units are paired the learner unit will have red LED on constantly indicates units in contact and will beep once If you do not hear a beep release the units and pair again step 5 7 Repeat this contact steps 5 and 6 for all other learner units you want to pair with the main unit 8 After the 2 minutes sending mode the main unit will return to disarmed mode The red LED will flash 3 times to confirm NOTE If you wish to exit the learning mode within the 2 minute duration press CLR button twice on the main unit to exit RANGE Minimum 1 metre maximum upto 25 metres
2. times Replace the back cover and fix with screw NOTE Please wait 30 seconds before inserting new batteries whenever you take old batteries out Care and maintenance To clean the unit simply use a soft slightly damp with water cloth and wipe dry immediately Caution Never use chemicals to clean the unit as this may cause damage to the plastic and result in the alarm not functioning 5j Setting the PIN code In order to use the unit you must set a 4 digit PIN code using the buttons 1 2 3 Yale The default setting of this is 1 2 3 Yale To change this 1 Enter the current PIN default set to 1 2 3 Yale 2 Press CLR the orange LED will be on for 3 seconds 3 Enter the new PIN code 4 Enter old PIN and press CLR 5 The orange LED will flash 3 times to confirm 6 The unit will return to disarm mode red LED will flash 3 times NOTE For security reasons if a delay of more than 5 seconds occurs between any of the above steps all LEDs will flash 3 times and the unit will beep to confirm an error the unit will return to disarm mode NOTE If this procedure is not completed correctly within 5 attempts the unit will lock for 5 minutes Installing the unit The unit has been designed to be either free standing or wall mounted To wall mount 1 Place the alarm in the desired location preferably with the PIR angled towards a door Operation Leaving the protected area Press the ARM button on the unit th
3. Troubleshooting The units red LED does not flash when the batteries are installed Ensure the batteries are connected correctly according to the diagram in the battery compartment The red light keeps flashing This is the low battery indicator Replace the unit s batteries Radio ON OFF The radio is default to be always on It is possible to disable the radio function if you are using just a single device in order to conserve power To turn ON radio Enter your 4 digit PIN followed by 2 1 1 1 1 To turn OFF radio Enter your 4 digit PIN followed by 2 Yale Yale Yale Yale Factory reset If you forget your PIN or the system malfunctions you can press the reset button locates behind battery cover to erase all memory Please ensure the device is powered and system is in Disarm mode After reset you will need to set up your PIN again and pair with other devices if required Battery precautions When using this product follow these precautions at all times e Use only the appropriate size batteries e Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Incorrect polarity may cause damage to the unit e Do not mix old and new batteries e lf the alarm is not used for long periods of time remove the batteries to prevent damage to the unit or injury from possible battery leakage Do not recharge batteries not intended to be recharged Always follow the ma
4. e red LED will quickly flash to confirm the unit is armed You have 20 seconds to vacate the area During this period 4 count down beeps with 4 single Green LED flashes will sound to warn of the exit period Entering the protected area Within 10 seconds of entering type in your 4 digit PIN code and press CLR The red LED will quickly flash and the unit will beep once to confirm the unit is disarmed NOTE If PIN entered incorrectly 5 times unit will beep 10 times and the unit will lock not do anything e g keypad locked for 5 minutes Unit continues in whatever mode it was in prior e g siren sounding Alarm activated If the unit is activated the siren will sound for 2 minutes The Orange LED will also flash this is to show which unit has been triggered if you have move than one device set up to work together Pairing the PIR with another unit from the range The standalone alarm range has been designed specifically to operate as single units or be paired together to work as kits Up to 3 of the master units those that have sensors as well as Sirens can be paired together The number of slave units those that do not have sensors that will work together is limitless This PIR is a master unit Each master unit has a unique radio code which can be sent to any other unit in order to make them work together The procedure for doing this is as follows 1 Starting with any master unit which you want to be the
5. nufacturers directions e Please only use alkaline batteries Wireless range If using as part of an extended system the range of these parts is a minimum of 1 meter up to a maximum of 25 meters System activity Please note when the red light is on the product is processing so no operation will work for example you will not be able to enter your PIN amp CEO WEEE Note Waste electrical products should Yale not be disposed of with household Yale waste Please recycle where facilities School Street Willenhall ist Check with local authority or 7 e n aa e West Midlands WV13 3PW Tel 44 0 1902 364606 Fax 44 0 1902 364692 email info yale co uk www yale co uk An ASSA ABLOY Group brand ASSA ABLOY An ASSA ABLOY Group brand SAA8011 Single room alarm with PIR User Manual Keep this manual safe for future reference ASSA ABLOY Product diagram Front 1 Front eyebrow contacts 2 Motion sensor 3 LED x 3 4 ARM amp CLR buttons 9 1 2 3 amp Yale buttons 6 Siren 1 Reset button 2 Battery compartment 3 Rear contact points Battery installation The battery compartment is located on the rear of the alarm unit It can be accessed by removing the screw from the back of the unit and lifting the cover Insert 4 AA Alkaline size batteries not included as shown on the diagram inside the compartment When the final batteries are inserted the centre red LED will flash 3

Troubleshooting - SD Fire Alarms

Contents

Download Pdf Manuals

Related Search

Related Contents