Home

S4 Zoom User Manual 0107.book

1. Step 2 Unlock and loosen the outer knob by turning it counterclockwise Step 3 Gently move the outer knob from side to side and up and down until the lamp is centered within the reflector Step 4 Once the lamp is centered turn the outer knob clockwise to lock it in place Step 5 Finally turn the inner knob either clockwise or counterclockwise to achieve an optimum flat field See Figure 5 Selecting the field angle and focusing the beam Locking lever push button Locking lever Light baffle Beam focus dial Figure 6 Step 1 Press the locking lever push button and lift the locking lever to unlock the focus dial as shown in Figure 6 Step 2 To reduce the field angle rotate the focus dial clockwise To enlarge the field rotate the dial counterclockwise Adjustments 5 Step 3 Once the desired field angle is established slide the light baffle forward to soften or backward to sharpen the edge Step 4 Once the field and edge are established press the locking lever to lock the focus dial into position Shaping the beam The beam can be shaped using the shutters see Figure 1 a pattern an optional drop in iris or by rotating the barrel Pattern Projection The pattern holder slot is on the top side of the barrel and in front of the shutters It accommodates A size B size and glass pattern holders see Figure 7 A Size Pattern holder
2. holds 3 diameter patterns B Size Pattern holder holds 2 5 and 2 75 diameter patterns lt 3 12 Diameter gt 4 2 75 Diameter gt Figure 7 Note Because the Source Four aperture is 3 inches wide ETC recommends using A size patterns for maximum pattern effectiveness Use an optional donut in the accessory holder to enhance pattern projection Donut diameter range should be 2 5 to 2 75 Drop In Iris Slot Drop in iris slot Iris eo Figure 8 The drop in iris slot is located on the top of the barrel and in front of the pattern holder slot It accommodates either a drop in iris or a motorized pattern device When the slot is not in use a small sheet metal cover secured with two Phillips screws prevents light leakage see Figure 8 Step 1 Use a screwdriver to loosen the screws on the drop in iris slot cover Do not remove thumbscrews Step 2 Slide the cover completely forward to expose the slot Step 3 Insert the iris or motorized pattern device For an iris install the flat side toward the shutters and make sure the iris handle extends from the slot Source Four Zoom User Manual Step 4 Slide the slot cover back toward the shutters until it meets the iris handle Leave enough space to move the iris handle Step 5 Secure the drop in iris slot cover by tightening the screws Rotating the barrel assembly Barrel 0 rotation knob _ Figure 9 Ste
3. 8 000 3 050 K 1000 hours HPL 750 120 750 120 21 900 3 250 K 300 hours HPL 750 120x 750 130 16 400 3 500 K 1500 hours HPL 575 120 575 120 16 520 3 250 K 300 hours HPL 575 120X 575 120 12 360 3 050 K 2000 hours HPL 750 230 750 230 19 750 3 200 K 300 hours HPL 750 230x 750 230 15 600 3 050 K 1500 hours HPL 575 230 575 230 14 900 3 200 K 400 hours HPL575 230X 575 230 11 780 3 050 K 1500 hours HPL 375 230X 375 230 7 250 3 000 K 1000 hours HPL 750 240 750 240 19 750 3 200 K 300 hours HPL 750 240x 750 240 15 600 3 050 K 1500 hours HPL 575 240 575 240 14 900 3 050 K 400 hours HPL575 240x 575 240 11 780 3 050 K 1500 hours HPL 375 240x 375 240 7 250 3 000 K 1000 hours To be used with ETC Dimmer Doubler Source Four Zoom User Manual Color frame holder Retaining clip in the eo position Figure 2 The color frame holder is equipped with a spring loaded retaining clip that prevents color frames and accessories from falling out See Figure 2 WARNING Make sure all color frame accessories are locked in position with the retaining clip before hanging the Source Four Step 1 Release the retaining clip by pushing it sideways while gently pulling backwards Step 2 Insert the color frame Step 3 Lock the retaining clip by pushing sideways while gently pushing forward Note The performance of saturated colors may be less than desirable in any theatrical lighting
4. and angle Setting the fixture height within the yoke The Source Four 25 50 Zoom has a two position yoke for modifying the overall height in which the fixture is mounted see Figure 11 To change the height position perform the following steps General use position Low clearance position YA i Yoke locking knob Figure 11 Step 1 Remove the yoke locking knobs washers and hex bolts from either side of the fixture Step 2 Raise or lower the fixture to the desired position within the yoke Step 3 Reinstall the yoke s hex bolts washers and locking knobs Step 4 Tighten the yoke knobs to secure in position Setting the angle within the yoke HO Yoke locking knob Figure 12 Step 1 Loosen the yoke locking knobs see Figure 12 Do not remove them Step 2 Tilt the fixture to the desired position Step 3 Tighten the yoke locking knobs to secure in position Source Four Zoom User Manual Adjusting the optional balance yoke position 15 30 Zoom The Source Four 15 30 Zoom has an optional balance yoke bracket ETC part 7060A2028 for repositioning the fixture s center of gravity It is also equipped with a moveable yoke for setting the fixture s angle Setting the balance yoke Balance yoke Moveable yoke Figure 13 Step 1 Loosen the balance yoke s clutch hex bolts on either side of the fixture Step 2 Adjust the balance yoke so it is perpendicular
5. 2 2799 9325 Service Americas service etcconnect com m UK service etceurope com m DE techserv hoki etcconnect com m Asia service etcasia com Web www etcconnect com m Copyright 2013 ETC All Rights Reserved m Product information and specifications subject to change 7060M1250 06 01 m Rev D m Released 2013 09
6. fixture especially when equipped with a 750w lamp For best results always use high quality color media rated for high temperature use ETC s optional Gel Extender part PSF1029 will provide maximum color media life The use of any gel extender accessory may limit the coverage of any wide angle lens or beam setting A variety of heat shield products is also available from many color media manufacturers Follow the manufacturer s instructions for the use of these products Basic Assembly Replacing the HPL Lamp __ HPL lamp Lamp retention brackets Lamp retainer clips Knurled bolt Figure 3 A lamp must be installed before you use the fixture Note Verify that the HPL lamp you intend to install is suitable for your facility s voltage 115 120 230 and 240 volt HPL lamps are available See Fixture information page 2 Operating HPL lamps above their rated voltage reduces lamp life and can cause premature lamp failure WARNING Let the lamp cool before replacing Step 1 Disconnect power to the Source Four before installing the lamp Step 2 Loosen the knurled bolt on the back of the lamp housing and pull the housing out Step 3 Holding by the base remove the HPL lamp from its box CAUTION Use caution when installing or replacing any lamp When installing replacing lamp be sure to point the lamp away from your face and away from others before inserting it firml
7. om rotate the lens tube to its limit in one direction approximately 25 so the extrusion door will clear the balance yoke See Figure 15 Step 1 Rotate the extrusion door fastener 1 4 turn to the right or left and open extrusion door Step 2 Set the lens to the narrowest field angle to maximize the distance between the lenses Step 3 Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 50 50 mixture of each can be used to clean the glass surface Step 4 Close the extrusion door and turn the fastener 1 4 turn to secure it Source Four Zoom User Manual Cleaning the reflector WARNING Unplug the fixture before attempting to clean the reflector To quickly clean the reflector remove the lens tube and clean the dust from the reflector with a blast of oil free air You may also wipe the reflector with a clean lint free cloth If either method is not sufficient follow these steps Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 To protect the lamp housing during cleaning remove the lamp housing by loosening the knurled bolt and pulling the housing straight out See Figure 3 Remove the barrel rotation knob located at the bottom of the barrel see Figure 1 Use a Phillips screwdriver to remove the retainer bolt located on top of the reflector housing Rotate the barrel 45 in either direction Caref
8. p 1 Loosen the barrel rotation knob directly behind the shutters on the underside of the reflector housing see Figure 9 Do not remove the barrel rotation knob Step 2 Rotate the barrel to the desired position up to 25 in either direction from the centered position Step 3 Once the barrel is positioned tighten the barrel s rotation knob to lock it in place Adjusting the C clamp C clamp a Pan screw x Pipe bolt Yoke bolt and a Yoke lockwasher _ Q O Figure 10 The C clamp attaches the fixture to the mounting pipe and allows you to adjust the position of the fixture once it is mounted see Figure 10 Step 1 Tightly fasten the C clamp to the yoke with the provided yoke bolt and lock washer Step 2 Place the C clamp on mounting pipe then tighten the pipe bolt to secure it Step 3 Loosen the C clamp pan screw and rotate the yoke to the desired position Step 4 Tighten the pan screw to lock the fixture A CAUTION Tighten C clamp pipe bolt to 15 20 ft lbs approximately finger tight plus up to one quarter turn Do not exceed 25 ft lbs Do not use excessive force Tighten the yoke pivot bolt to 5 10 ft lbs approximately finger tight plus up to one eighth turn Do not exceed 15 ft lbs Do not use excessive force Adjustments 7 Adjusting the yoke position 25 50 Zoom The Source Four 25 50 Zoom provides multi positioning capabilities within its yoke for overall fixture height
9. puree tour Zoom User Manual Production Dates September 2004 Present Copyright Electronic 2013 Theatre Controls Inc All Rights reserved Product information and specifications subject to change Part Number 7060M1250 06 01 Rev D Released September 2013 Picking 7060M1008 D Table of Contents Basic Assembly ocs oenas idad vraat eee beeen ene 1 Fixture information 0 0 erok EEE eae 2 Color frame holder 2 0 0 0 cece eee 3 Replacing the HPLLamp 00200 e eee eee 4 AGjUStMONIS raes 9 hae eae oh ee ae ce eee ae hae E 5 Centering lamp and adjusting the field 5 Selecting the field angle and focusing the beam 5 Shaping the beam 1 eae 6 Rotating the barrel assembly 0000 a eee eee 7 Adjusting the C clamp 000 cee eee eee 7 Adjusting the yoke position 25 50 Zoom 8 Adjusting the optional balance yoke position 15 30 Zoom 9 Cleaning Lens and Reflector 0 0 0 c eee ee eee 10 Cleaning glass lens 0 ee eee 10 Cleaning the reflector 0 0 0 eee eee 11 ETC Emphasis Expression Insight Imagine Focus Express Unison Obsession I1 ETCNet2 EDMX Source Four Revolution Sensor and WYSILink are either registered trademarks or trademarks of Electronic Theatre Controls Inc in the United States and other countries All other trademarks bo
10. th marked and not marked are the property of their respective owners i Table of Contents Basic Assembly Insulated handle Lamp housing Yoke Drop in iris slot Optional lt v4 Balancing yoke Color frame retaining gel clip Color A WARNING Please note the following safety warnings before use Do not mount the fixture on or near combustible surfaces Do not operate the fixture without a lens installed Always hang the fixture with the color frame retaining clip in the locked position Remove cardboard insert from lens tube before connecting power to your fixture Shutters Focus dial Figure 1 Basic Assembly 1 Fixture information HPL lamp table CAUTION Do not use lamps other than the HPL in Source Four fixtures Use of lamps other than HPL will void UL cUL safety compliance and your warranty Lamp code Watts Volts Initial Lumen Color temp Average rated life HPL 780 77 750 77 22 950 3 250 300 hours HPL 550 77 550 77 16 170 3 250 300 hours HPL 550 77X 550 77 12 160 3 050 2000 hours HPL 750 115 750 115 21 900 3 250 K 300 hours HPL 750 115X 750 115 16 400 3 050 1500 hours HPL 575 115 575 115 16 520 3 250 K 300 hours HPL 575 115X 575 115 12 360 3 050 K 2000 hours HPL 375 115 375 115 10 540 3 250 K 300 hours HPL 375 115X 375 115
11. to the fixture as shown in Figure 13 If front of the fixture has several accessories attached you may need to tilt the balance yoke towards the front of the fixture to adjust the balance Step 3 Tighten the balance yoke s clutch hex bolts to secure the yoke into position CAUTION Once the balance yoke is locked adjustments should only be made to the moveable yoke Setting the angle within the moveable yoke Horizontal mounting Vertical mounting Gj Yoke locking knob Figure 14 Step 1 Loosen the moveable yoke s locking knobs Do not remove them Step 2 Tilt the fixture to the desired position as shown in Figure 14 Step 3 Tighten the yoke s locking knobs to secure the fixture in position Adjustments 9 Cleaning Lens and Reflector WARNING Do not use ammonia based or other harsh commercial cleaners Clean lens and reflector only as directed Commercially available glass cleaning agents should be avoided as they may contain ammonia other harsh chemical detergents or abrasive agents These cleaners may damage the glass surface and the Anti Reflective coatings Do not immerse or soak the glass in any cleaning solution Replace lenses if they contain visible damage cracks or deep scratches that may impair their effectiveness Cleaning glass lens Extrusion door Le Turn to the left x or right yo F Figure 15 Note To clean the 15 30 Zo
12. ully remove the barrel from the reflector housing Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 50 50 mixture of each can be used to clean the glass surface Gently wipe the reflector Insert the barrel into the reflector housing with the iris pattern slot on top Align the triangles on both parts While gently pressing in rotate the barrel 45 clockwise until it sets into position then rotate the barrel counterclockwise 45 The barrel should be firmly attached and the triangles should be aligned Reinstall the barrel rotation knob and tighten the retainer bolt Reinstall the lamp housing and tighten the knurled bolt Cleaning Lens and Reflector 12 Source Four Zoom User Manual Cleaning Lens and Reflector 13 KE Corporate Headquarters 3031 Pleasant View Road P O Box 620979 Middleton Wisconsin 53562 0979 USA m Tel 608 831 4116 m Fax 608 836 1736 London UK Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6UU UK m Tel 44 0 20 8896 1000 m Fax 44 0 20 8896 2000 Rome IT a Via Pieve Torina 48 00156 Rome Italy Tel 39 06 32 111 683 Fax 39 06 32 656 990 Holzkirchen DE Ohmstrasse 3 83607 Holzkirchen Germany m Tel 49 80 24 47 00 0 Fax 49 80 24 47 00 3 00 Hong Kong Rm 1801 18 F Tower 1 Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong m Tel 852 2799 1220 Fax 85
13. y into the assembly This may prevent injuries if the lamp should break INCORRECT XH CORRECT Note To avoid premature lamp failure do not touch the lamp glass If you do clean it carefully with isopropyl alcohol and a clean lint free cloth Allow to dry before operation Step 4 Align the flat sides of the lamp base with the retention brackets on either side of the socket as shown in Figure 3 Step 5 Push down on the lamp base until the lamp seats firmly When properly installed the top of the lamp s base will be even with he top edges of the retention brackets CAUTION Improperly installed lamps cause premature lamp failure and socket problems Step 6 Press lamp retaining clip across lamp base to secure Step 7 Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt Source Four Zoom User Manual Adjustments Centering lamp and adjusting the field Flat field best adjustment Rear lamp Inner Knob housing peak flat field adjustment Hot spot lamp pulled out too far Field with hole lamp Outer Knob lam pushed in too far center adjustment Figure 4 Figure 5 The two concentric knobs located on the lamp housing allow you to align the lamp and adjust its field See Figure 4 The outer knob centers the lamp within the reflector The inner knob adjusts the lamp s field Step 1 Turn on the Source Four and aim it at a flat surface Adjust the barrel to create a hard edge

S4 Zoom User Manual 0107.book

Contents

Download Pdf Manuals

Related Search

Related Contents