Design House 702282 Installation Guide
Contents
1. ERIOR CYLINDER EXTERIOR TAIL PIECE2. LA3 INSTRUCTIONS FOR INSTALLATION OF SINGLE OR DOUBLE CYLINDER DEADBOLTS AND THE REPLACEMENT OF EXISTING LOCKS 1 MARK DOOR a Fold and apply template on high edge of door bevel and mark center of door edge as indicated on template at the desired height from the floor b Mark center hole on door face through guide on template for either 2 3 8 or 2 3 4 60mm or 70mm backset NOTE BACKSET ON DOOR FACE MUST BE SAME AS BACKSET OF YOUR LOCK 2 DRILL HOLES Drill holes as marked A NOTE DRILL 2 1 8 54mm O HOLE FROM BOTH SIDES OF DOOR TO AVOID SPLITTING WOOD 1 25mm 2 1 8 54mm HOLE FOR DEADBOLT FOR LOCKSET 3 INSTALL LATCH e Insert latch in hole Chisel 1 8 3mm Insert latch and Mark outline of deep or until face tighten screws face plate and plate flush with remove latch door edge 4 INSTALL STRIKE screw holes on strike with center lines on jamb Mark outline and chisel 5 64 2mm deep for strike Close door to mark Measure one half horizontal center of door thickness line of strike from door stop and mark vertical center line of strike Drill 1 25mm hole 1 25 mm deep at inter LA3 FOR USE ON DOOR THICK 1 3 8 TO 1 3 4 35mm 45mm TOOLS REQUIRED FOR NEW CONSTRUCTION 1 philips head screwdriver 1 2 1 8 54mm hole saw 1 1 25mm drill amp 1 chisel TOOLS REQUIRED FOR REPLACEMENT 1 philips head screwdriver 5 INSTALL SI
3. NGLE CYLINDER EXTERIOR CYLINDER a Retract deadbolt to unlock position EXTERIOR TAIL PIECE b Insert exterior tail piece horizontally through latch crank c Press exterior cylinder flush against door d Install inside turn unit and tighten installation screws EXTERIOR CYLINDER INSTALLATION SCREW 6 INSTALL DOUBLE CYLINDER EXTERIOR CYLINDER a Retract deadbolt to unlock position b Insert exterior tail piece horizontally through latch crank c Press exterior cylinder flush against door d Insert interior tail piece vertically through latch crank e Press interior cylinder flush against door and tighten installation screws O x KEY HOLE EXTERIOR CYLINDER EXTERIOR TAIL PIECE Do KEY HOLE LA3 INSTRUCTIONS FOR INSTALLATION OF SINGLE OR DOUBLE CYLINDER DEADBOLTS AND THE REPLACEMENT OF EXISTING LOCKS 1 MARK DOOR a Fold and apply template on high edge of door bevel and mark center of door edge as indicated on template at the desired height from the floor b Mark center hole on door face through guide on template for either 2 3 8 or 2 3 4 60mm or 70mm backset NOTE BACKSET ON DOOR FACE MUST BE SAME AS BACKSET OF YOUR LOCK 2 DRILL HOLES Drill holes as marked A NOTE DRILL 2 1 8 54mm O HOLE FROM BOTH SIDES OF DOOR TO AVOID SPLITTING WOOD 1 25mm 2 1 8 54mm HOLE FOR DEADBOLT FOR LOCKSET 3 INSTALL LATCH Insert la
4. tch in hole Chisel 1 8 3mm Insert latch and Mark outline of deep or until face tighten screws face plate and plate flush with remove latch door edge 4 INSTALL STRIKE screw holes on strike with center lines on jamb Mark outline and chisel 5 64 2mm deep for strike At Close door to mark Measure one half horizontal center of door thickness line of strike from door stop and mark vertical center line of strike Drill 1 25mm hole 1 25 mm deen at inter LA3 FOR USE ON DOOR THICK 1 3 8 TO 1 3 4 35mm 45mm TOOLS REQUIRED FOR NEW CONSTRUCTION 1 philips head screwdriver 1 2 1 8 54mm hole saw 1 1 25mm drill amp 1 chisel TOOLS REQUIRED FOR REPLACEMENT 1 philips head screwdriver 5 INSTALL SINGLE CYLINDER EXTERIOR CYLINDER a Retract deadbolt to unlock position EXTERIOR TAIL PIECE b Insert exterior tail piece horizontally through latch crank c Press exterior cylinder flush against door d Install inside turn unit and tighten installation screws EXTERIOR CYLINDER INSTALLATION SCREW 6 INSTALL DOUBLE CYLINDER EXTERIOR CYLINDER a Retract deadbolt to unlock position b Insert exterior tail piece horizontally through latch crank c Press exterior cylinder flush against door d Insert interior tail piece vertically through latch crank e Press interior cylinder flush against door and tighten installation screws O X KEY HOLE EXT
Download Pdf Manuals
Related Search