Home

Zinsser 249020 Use and Care Manual

1. per gallon Tinting the primer toward the color of the topcoat helps hide in one coat For mid or deep tone colors use Bulls Eye 1 2 3 Deep Tint Shake or stir well before using DRY TIME Dries to the touch in 30 minutes can be recoated in 1 hour Lower temperatures higher humidity and the addition of tint will prolong dry and cure time Allow more time at cooler temperatures CLEAN UP Clean up spills and paint drips with detergent and warm water Wipe up splatters before they dry If spills or drips have dried use denatured alcohol or ammoniated detergent to soften and remove primer Wash application tools in detergent and warm water immediately use Follow equipment manufacturer s directions to clean spray equipment Dispose of unused or unwanted product in accordance with local laws regulating water based coatings Form GDH 70 Rev 053013 TECHNICAL DATA BULLS EYE ZERO PHYSICAL PROPERTIES Physical Properties BULLS EYE ZERO Resin Type Water based Acrylic Pigment Type Titanium Dioxide Solvents Waiter Glycol Ethers Weight Per Gallon 10 7 lbs Per Liter 1 28 kg Solids By Weight 49 4 By Volume 34 4 Volatile Organic Compounds 0 g l Recommended Dry Film 1 0 1 5 mils Thickness DFT per Coat 25 37 5p Wet Film to Achieve DFT Unthinned 3 0 4 5 mils material 75 112 5y Theoretical Coverage at 552 sq ft gal 1 mil DFT 25p 13 6 m I Practical Cov
2. the National Lead Information Hotline at 1 800 424 LEAD or log on to www epa gov lead LIMITATIONS Bulls Eye Zero is not recommended for applications to floors decks roof surfaces or any surface subject to immersion or prolonged contact with water APPLICATION Apply only when air material and surface temperatures are between 50 85 F 10 29 C and the relative humidity is below 85 Thoroughly mix to ensure any settled pigment is re dispersed before using In most cases only one coat is necessary to prime most surfaces If excessive absorption occurs over very porous substrates a second coat may be necessary Spot priming is recommended only under high hiding topcoat finishes For best results prime entire surface before painting Apply with a synthetic nylon polyester or blend bristle brush roller or airless sprayer Follow manufacturer s instructions when using spray equipment For airless spraying use a 017 tip at 2000 to 2500 psi Wear NIOSH approved respirator and provide adequate ventilation Form GDH 70 Rev 053113 TECHNICAL DATA BULLS EYE ZERO PRODUCT APPLICATION cont THINNING Bulls Eye Zero is formulated to be used without thinning If thinning is necessary add no more than 10 fluid ounces of clean water per gallon and mix thoroughly Note that excessive thinning will hinder stain blocking properties TINTING Bulls Eye Water Base may be tinted with up to 2 ounces of universal colorant
3. Pp TECHNICAL DATA BEY 04 BULLS EYE ZERO ZINSSER QUALITY SINCE 1849 DESCRIPTION AND USES Zinsser Bulls Eye Zero is a high performance eco friendly water based primer for interior and exterior applications This product has been formulated to meet clean air regulations to provide a fast drying low odor primer sealer with excellent adhesion enamel holdout and stain blocking properties Bulls Eye Zero delivers the performance of oil based primers with none of the odors or solvents that contribute to poor air quality Bulls Eye Zero is excellent for use in residential institutional or commercial use in schools hospitals hotels nursing homes restaurants etc Use on interior and exterior new or previously painted drywall wood pine fir cedar redwood plywood T 111 cured plaster masonry stucco cement poured concrete concrete block hardboard vinyl PVC fiberglass tile Metal aluminum steel galvanized metal Adheres to tough surfaces such as chalky exterior siding and trim high gloss enamels old varnish tile galvanized metal and hardboard Seals unpainted porous surfaces extending the coverage of the topcoat Bulls Eye Zero is an excellent under coater for oil or latex enamels and provides high holdout and smooth sanding surface necessary to prevent variations in topcoat gloss Bulls Eye Zero locks in stains such as residual nail head dust asphalt creosote tannin bleed for
4. cedar or redwood lipstick crayon oil grease handprints most ball point and felt tip pen marks When priming over bare cedar or redwood allow 24 hours dry time before painting Persistent stains may require a second coat PERFORMANCE CHARACTERISTICS For interior amp exterior use Sticks to all surfaces Seals common stains Low odor Mildew resistant film Dries in 1 hour PRODUCTS SKU Description 249019 1 Quart 249020 1 Gallon 249021 5 Gallon PRODUCT APPLICATION SURFACE PREPARATION Surfaces should be clean dry sound and free of any contamination mildew rust or unsound coatings that may interfere with adhesion Remove loosely adhered or unsound coatings Sand any remaining paint film edges smooth If unsure of cleanliness always wash surface with household ammonia and water solution appropriate cleaning solution or solvent do not use TSP as a cleaner Rinse the surface thoroughly and allow to dry before application of the primer Spot prime knots and sap streaks with Zinsser B I N Primer Sealer WARNING If you scrape sand or remove old paint you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH Approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting
5. erage at Recommended DFT assume 15 material loss Approximately 400 sq ft gal 9 8 m l depending on application method and surface porosity Touch 30 45 minutes Broa peas T Recoat 1 hour Relative Humidity Full Cure 2 days Shelf Life 5 years Flash Point gt 200 F 93 C MPI Certified 17 50 137 149 Storage Store indoors at 40 80 F 4 26 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice ge RUST OLEUM BRANDS Rust Oleum Corporation Form GDH 70 11 Hawthorn Parkway Phone 877 385 8155 Rev 053113 Vernon Hills Illinois 60061 www rustoleum com An RPM Company

Zinsser 249020 Use and Care Manual

Contents

Download Pdf Manuals

Related Search

Related Contents