Home

Newstar KVM extender, UTP, PS/2

1. 3 See the Grounding Information card that came with this package for proper grounding details Continues on next page 11 Installation guide Continued from previous page 4 For increased grounding protection use STP shielded twisted pair cable to connect the local and remote units There are two methods that can be used a In addition to the eight paired wires STP cable also contains a grounding wire Solder this wire to the RJ 45 connector as shown in the diagram below 7 b The second method is to use the STP cable shielding for grounding In this case make sure that the shielding makes tight contact with the top inside of the RJ 45 connector as shown in the diagram below In either case make sure that the sides of the RJ 45 connector make tight contact with the grounding contacts on the sides of the RJ 45 socket as shown in the diagram below e i 12 Installation guide LEWSTAL Chapter 2 Hardware Setup Connecting Up Refer to the installation diagram on the following page the numbers in the diagram correspond to the numbers of the steps as you perform these steps 1 Plug the cables from the local console devices keyboard monitor mouse into their ports on the rear panel of the Local Unit 2 Plug the SPHD end of the KVM cable supplied with this unit into the KVM port on the front panel of the Local Unit Note The shape and function of the co
2. Installation guide LEWSTAL Chapter 2 Hardware Setup device is provided on page 17 Please review it before I 1 Important safety information regarding the placement of this proceeding 2 Make sure that power to all the devices you will be installing has been turned off You must unplug the power cords of any computers that have the Keyboard Power On function Rack Mounting For convenience and flexibility the local and remote unit can be mounted on system racks To rack mount a unit do the following 1 Unscrew either the two front screws or two rear screws from the bottom panel Installation guide LEWSTAL 2 Use the screws you just removed to attach the mounting bracket that came with your package to the unit 3 Screw the bracket into any convenient location on the rack 10 Installation guide LEWSTAR Chapter 2 Hardware Setup Installation Grounding To prevent damage to your installation it is important that all devices are properly grounded 1 Use the two grounding wires supplied with this package to ground both units by connecting one end of the wire to the grounding terminal and the other end of the wire to a suitable grounded object 2 Make sure that the computer that the local unit connects to and the monitor that the remote unit connects to are properly grounded STP Cable o 0 Cat 5 or higher up to 150 m o o
3. Model NS560UTP PRO Installation guide LEWSTAR FCC Information This is an FCC Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense RoHS This product is RoHS compliant SJ T 11364 2006 The following contains information that relates to China Er ES SA EN taat O O O O O mat O O o o O O O RPA SARRE E HAE EAST 11363 2006 l EHRE EKZ Fo O RTRAAKEWARAR 6758595 DIAZ HRA SMW SJ T 11363 2006 R E E gt X RNKASESVRELEZRAENER DRM Nees HHSJ T 11363 20064 BREA o cere de Installation guide LEWSTAL User Notice All information documentation and specifications contained in this manual are subject to change without p
4. away from dust dirt and harsh environmental influences The unit is also useful for control and security purposes since you can store the system unit in a secure area at the same time that you put the console in a location that offers convenient access The NewStar KVM Extender provides the ideal means to access the remote system box since it improves on previous designs by using compact inexpensive Cat 5 cable the kind commonly used in Ethernet networks instead of bulkier more expensive standard cables Cat 5 makes for a much neater more convenient more reliable data transfer connection A key feature of the unit is built in 8K V ESD protection and 2K V surge protection It also features a custom ASIC that ensures the utmost in reliability and compatibility It senses the distance to the system and automatically adjusts the gain to compensate Setup is as easy as can be simply connect the computer system box and local console to the Local module run the Cat 5 cable to the Remote module Up to 150 meters away and plug the remote console into the Remote Module Note You can control numerous remote systems from a single console by combining the extender with a KVM switch Installation guide LEWSTAR Features Cat 5 or higher cable to connect the Local and Remote Units up to 150 m apart Dual console operation control your system from both the local and remote PS 2 keyboard mouse and m
5. Wes 1 IB Emo AE CED 000 Installation guide Chapter 3 Operation Operating Modes The NewStar KVM Extender has two operating modes Local and Remote as described in the table below Mode Description Local Only the local console has KVM keyboard video mouse access The remote console s monitor is blank and the remote console s keyboard and mouse input is disabled Local Remote Both the local and remote consoles can have KVM access However they cannot both have access at the same time The console without access has to wait until the console with access stops inputting data before it can gain access Mode Selection The Operating Mode Selection Switch located on the local Front panel controls the operating mode of the KVM Extender system Pressing the switch Toggles the system between Local and Local Remote operating modes 15 Installation guide LED Display The Local and Remote Units have front panel LEDs to indicate their operating status as shown in the tables below Local Unit Operating Mode LED Local Lights to indicate Lights when the local console is active the Remote that the local LED is out console is active Turns off when the remote console is active the et Remote LED is Remote LED turns on out Flashes on and off alternately with the Remote LED when neither conso
6. the system A VGA SVGA or Multisync card A 6 pin mini DIN mouse port A 6 pin mini DIN keyboard port Cables For optimum signal integrity we strongly recommend that you use the high quality Custom KVM cable provided with this package The shape and function of the KVM connectors on the switch and the cable have been modified so that only KVM cables designed to work with this KVM switch can be used Cat 5 cable is the minimum required to connect the local and remote units Installation guide LEWSTAL Operating Systems Supported operating systems are shown in the table below OS Version Windows 2000 and higher Linux 7 4 and higher 9 0 and higher 9 0 and higher UNIX AIX 4 3 5L 5 2 5 3 FreeBSD 4 2 4 5 Novell Netware 6 0 and higher OS 2 Warp and higher OS Languages English American English UK French German Japanese Chinese Traditional Installation guide Components Local Unit Front View Description Function 1 Grounding The grounding wire used to ground the unit attaches here Terminal 2 KVM Port The KVM cable that links the local unit to your computer plugs in here Only KVM cables designed to work with this switch can be used 3 Remote LED The Local Unit has two LEDs to indicate the operating status of the Local and Remote units 4 Local LED See Local Unit page 16 for operating status details 5 Operating Mode Pressing thi
7. with this package is properly plugged into the remote unit s power jack 21 Installation guide Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM THE DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and specially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquires please contact your direct vendor 22 Installation guide C NS560UTP PRO LOCAL Front View 5 Rear View 7 NS560UTP PRO REMOTE Front View 6 Rear View 7 Components 5 NS560UTP PRO Front View 5 NS560UTP PRO Front View 6 Rear View 7 Connecting Up 13 G Grounding 11 Installation Connecting Up 13 Grounding 11 L LED Display Local 16 Remote 16 Limited Warranty 22 M Mode Selection 15 O Online VSIA Ks computerproducts Index Registration iii Operating Modes 15 R Rack mounting 9 Rear View 7 Requirements Cables 3 Operating Systems 4 OS Support 4 RoHS ii S Safety Instru
8. F N A Power 1 x DC Jack Unit to Unit 1 x RJ 45 LEDs Local 1 Green N A Remote 1 Green N A Power N A 1 Green On Line N A 1 Green Emulation Keyboard Mouse PS 2 Video 1280 x 1024 60Hz 150 m DDC DDC2 DDC2B I P Rating DC 5 0V 2 6A Power Consumption DC 5 0V 1 25W max 0 50 C 20 60 C 0 80 RH Metal 0 33 kg 0 32 kg 12 50 x 8 15 x 2 50 cm Environment Operating Temp Storage Temp Physical Properties DDC DDC2 and DDC2B support is for the Local monitor only 20 Installation guide Appendix TP Wiring Diagram and Pin Assignments PAIR 3 Pin Assignment 1 N OUT B 2 V OUT B 3 N OUT G 12345678 W O O W G Bl W Bl G W Br Br 4 N OUT R JACK POSITIONS 5 V OUT R 6 V OUT G T568B AT amp T 258A h ee 8 DO Troubleshooting Problem Action No video Make sure that all cables are securely plugged into their sockets Poor video quality The video quality can be improved by reducing the refresh rate Trails and smearing on the Unplug the Cat 5 cable from the remote unit then screen replug it Local Unit not working The power from the local computer computers in the KVM installation may be insufficient You may need to purchase a power adapter for use with the local unit Be sure to get one with the same specifications as the one provided in this package for the local units Remote Unit not working Make sure the power adapter that came
9. ctions General 17 SJ T 11364 2006 ii Specifications 20 System Requirements Computers 3 T Technical Support 19 Telephone support iii TP Pin Assignments 21 Wiring Diagram 21 Troubleshooting 21 U User Notice iii 23 Model NS560UTP PRO
10. ion system cables and power cables carefully Be sure that nothing rests on any cables Never push objects of any kind into or through cabinet slots They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock Do not attempt to service the device yourself Refer all servicing to qualified service personnel If the following conditions occur unplug the device from the wall outlet and bring it to qualified service personnel for repair The power cord or plug has become damaged or frayed Liquid has been spilled into the device The device has been exposed to rain or water The device has been dropped or the cabinet has been damaged The device exhibits a distinct change in performance indicating a need for service Il The device does not operate normally when the operating instructions are followed Only adjust those controls that are covered in the operating instructions Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair Do not connect the RJ 11 connector marked UPGRADE to a public telecommunication network 18 Installation guide Specifications Function LOCAL REMOTE Console Selection 1 x Pushbutton Connectors Console Ports KB 1 x 6 pin Mini DIN F Purple Video 1 x HDB 15 F Mouse 1 x 6 pin Mini DIN F Green KVM Ports 1 x SPHD 15
11. le is active Remote The LED is Off Lights when the remote console is active the Local LED is out Turns off when the local console is active the Local LED turns on Flashes on and off alternately with the Local LED when neither console is active Remote Unit LED Indication Power Lights steadily to indicate that the connection to the Local Unit is ok Flashes when there is a problem with the connection to the Local Unit On Line Lights when the remote console is active Is Off when the local console is active Is Off when there is a problem with the connection to the Local Unit 16 Installation guide LEWSTAR Appendix Safety Instructions General IH Read all of these instructions Save them for future reference Follow all warnings and instructions marked on the device Do not place the device on any unstable surface cart stand table etc If the device falls serious damage will result Do not use the device near water Do not place the device near or over radiators or heat registers Il The device cabinet is provided with slots and openings to allow for adequate ventilation To ensure reliable operation and to protect against overheating these openings must never be blocked or covered Il The device should never be placed on a soft surface bed sofa rug etc as this will block its ventilation openings Likewise the device should not be placed in a built in enclosure unless adequa
12. maged in shipping If you encounter a problem contact your dealer Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit and or any of the devices connected to it Installation guide LEWSTAL Contents FGG Information ss iia n a aces ii ROHS ord cee leleine a ee es ea ii User Information LL iii User Notice ios radar ea at a ere eee oe ili Package GoOntents cisuias rones ooo sed baie stews iv COMES eg oie ao ae ee r a eae ee et n V About this Manual vii Product Informatoni L ciriieei erre ed viii 1 Introduction OVEIVIOW gt sra e resine Se SAG A AAA SS 1 F at reS rai lesione ea aa 2 Requirements esti AA a i 3 A 3 Computers 24s Ca eae ra Sas Cade eee ee 3 CAU cia beh ove eT eee Hee ea eee Sa cs pa s 3 Operating SysSt MS cio rd e an 4 OS LANGUAGES ira ea 4 COMPONENTS siisii orron isie hea eaea eiai e da 5 NS560UTP PRO Local Unit Front View 5 NS560UTP PRO Remote Unit Front View 6 NS560UTP PRO Rear View Li 7 2 Hardware Setup RAcKMDUNIAO lt s roi ds ene exe a haa ds 9 Installation spp ert aa ene BY Re ee RR ee a 11 GIoUndnd si wins di Seek eae eee bia a 11 Connecting UD sere se iena 13 3 Operation Operating MOdes o escra i rana 15 Mode Selec vive cee ded ody dey ees chy ra 15 LED Display cri ii 16 NSS60UTP PRO Local Unit ecos i444 year deeded ee
13. nnectors on the cable and KVM switch have been modified so that only KVM cables designed to work with this switch can be used 3 Plug the connectors on the other end of the cable into the appropriate ports on the computer or Console section of the KVM switch if you are using one Each connector is marked with an appropriate icon to indicate itself 4 Plug one end of a Cat 5 or higher STP cable into the local s Remote I O port Plug the other end of the cable into the remote s Remote I O port Note STP cable is not supplied with this package It requires a separate purchase The cable can be up to 150 m 500 ft long 5 Plug the cables from the remote console devices keyboard monitor and mouse into their ports on the Console side of the remote unit 6 Plug the power adapter supplied with this package into an AC source plug the adapter s power cable into the Remote Unit s power jack 7 If you choose to use a power adapter with the local unit plug the power adapter into an AC source plug the adapter s power cable into the Local s Power Jack Note Use of a power adapter with the local unit is optional Refer to the note regarding the power jack on page 7 for details 13 Installation guide NS560UTP PRO LOCAL paa Q NS560UTP PRO LOCAL NS560UTP PRO REMOTE 14 he CS EX
14. onitor consoles Pushbutton selection of the active console High resolution video up to 1280 x 1024 60 Hz Supports VGA SVGA and Multisync monitors local monitor supports DDC DDC2 DDC2B Supports Microsoft Intellimouse and the scrolling wheel on most mice Automatic gain control automatically adjusts signal strength to compensate for distance Built in 8KV ESD protection and 2KV surge protection Built in ASIC for greater reliability and compatibility Local unit takes its power from the computer external power is only required when the power from the local computer computers in the KVM installation is insufficient O Rack mountable Note Ifyou choose to purchase a power adapter for use with the extender be sure to get one with the same specifications as the one provided in this package for the remote unit Installation guide LEWSTAL Requirements Console A VGA SVGA or Multisyne monitor capable of the highest resolution that you will be using on any computer in the installation A PS 2 keyboard A PS 2 mouse Note 1 Ifyou connect a DDC type monitor to the Local Unit the monitor that connects to the Remote Unit must be able to support the highest video resolution that the DDC monitor can provide 2 You must use the same brand and model of mouse on both the local and remote units Computers The following equipment must be installed on each computer that is to be connected to
15. rior notification by the manufacturer The manufacturer makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose Any of the manufacturer s software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not the manufacturer its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software The manufacturer of this system is not responsible for any radio and or TV interference caused by unauthorized modifications to this device It is the responsibility of the user to correct such interference The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE Installation guide LEWSTAL Package Contents The KVM Extender package consists of KVM Extender Local Unit KVM Extender Remote Unit Custom KVM Cable 1 8 m Power Adapter Rack Mount Kit Grounding Wires 1 2 m User Manual Quick Start Guide Grounding Information Card I e e Check to make sure that all the components are present and that nothing got da
16. s 16 NS560UTP PRO Remote Unit o o oo oooooooooo 16 Installation guide LEWSTAR Appendix Safety Instructions spira A eR Re so 17 o ar n ee 17 SOCCIIGAUONS 3 22 324425c8048 da iria iano 20 TP Wiring Diagram and Pin Assignments naaa aaa aaa 21 TOUBIESSAODUNO vencer dress besd dada 21 Limited Wiarranlyi sc s020eli pe ir ia es 22 vi Installation guide LEWSTAL About this Manual This User Manual is provided to help you get the most from your system It covers all aspects of installation configuration and operation An overview of the information found in the manual is provided below Chapter 1 Introduction introduces you to the system Its purpose features and benefits are presented and its front and back panel components are described Chapter 2 Hardware Setup describes how to set up your installation Chapter 3 Operation explains the fundamental concepts involved in operating the unit An Appendix provides specifications and other technical information regarding the unit vii Installation guide LEWSTAL Chapter 1 Introduction Overview The NewStar KVM Extender allows access to a computer system from a remote console keyboard monitor and mouse It is perfect for factory and construction sites or any type of installation where the console needs to be in a conveniently accessible location but you want the system equipment to reside in a safe place
17. s button toggles between the Local and Remote Selection operating modes See Operating Modes page 15 for Switch operating mode details Note Ifyou are combining the extender with a KVM switch the KVM cable connects to the respective ports on the Console section of the switch Installation guide Remote Unit Front View Description Function 1 Grounding The grounding wire used to ground the unit attaches here Terminal 2 On Line LED These LEDs indicate the operating status of the Local and 3 PowerLED Remote units See Remote Unit page 16 for details Installation guide Chapter 1 Introduction Rear View Description Function 1 The cable from the DC Power Adapter plugs into this jack 2 Mouse Port The console mice plug into these ports 3 Keyboard Port The console keyboards plugs into these ports 4 Link Port The Cat 5 cable that connects the Remote and Local units plugs into this connector 5 Video Port The console monitors plug into these ports Note The NSS60UTP PRO local unit can get its power from the computer external power is only required when the power from the local computer computers in the KVM installation is insufficient If you choose to purchase a power adapter for use with the unit be sure to get one with the same specifications as the one provided in this package for the extender Installation guide NOTES
18. te ventilation has been provided Never spill liquid of any kind on the device I Unplug the device from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning Il The device should be operated from the type of power source indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company The device is designed for IT power distribution systems with 230V phase to phase voltage Ml The device is equipped with a 3 wire grounding type plug This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not attempt to defeat the purpose of the grounding type plug Always follow your local national wiring codes Do not allow anything to rest on the power cord or cables Route the power cord and cables so that they cannot be stepped on or tripped over If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the 17 Installation guide LEWSTAR extension cord ampere rating Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes M To help protect your system from sudden transient increases and decreases in electrical power use a surge suppressor line conditioner or un interruptible power supply UPS I Posit

Newstar KVM extender, UTP, PS/2

Contents

Download Pdf Manuals

Related Search

Related Contents