Home

0150-0238A DSR-1000eZ User Manual

1. NTSC Record Speeds 60 30 20 10 5 3 2 1 0 5 0 2 0 1 0 0 PAL Record Speeds 50 25 17 10 5 3 2 1 0 5 0 2 0 1 0 0 8 When finished entering the Record Speed use the Shuttle to navigate to the QUALITY setting 9 Use the Jog to enter the record quality Low Medium or High Higher record quality settings use more disk space 10 When finished entering the Record Quality use the Shuttle to navigate to the ON OFF setting 11 Use the Jog to Activate Deactivate or Delete the recording 12 When finished press the Enter button to exit the Edit mode Use the Jog Shuttle to navigate to OK then press the Enter button to complete the selection Editing a Timed Recording 1 Using the Jog Shuttle to navigate highlight the event parameter you wish to edit 2 Press the Enter button to enter the Edit mode EDIT MODE will appear on screen in the lower left hand corner of the pop up menu 3 Use the Jog to change the values Use the Shuttle to navigate among parameters in the same row 4 When finished press the Enter button to exit the Edit mode Use the Jog Shuttle to navigate to OK then press the Enter button to complete the selection Calibur DSR 1000eZ 4 4 0150 0238A Deleting a Timed Recording 1 Using the Jog Shuttle to navigate highlight the ON OFF parameter of the event you wish to delete Press the Enter button to enter the Edit mode Use the Jog to select DEL from the menu Pres
2. The Main Menu The Main menu provides access to all of the operator programmable options Each sub section of the Main menu is described briefly in this section For complete information about operator programming in the Main menu see section 4 a Main Menu Time Date Use this menu to specify e The time format 12 or 24 hours e The date format MM DD YY DD MM YY or YY MM DD e Thetime e The date a Main Menu gt Alarms Use this menu to specify unit detects a signal on the Alarm In connection e Whether a teletext alarm signal generated by a multiplexer or other device will cause the unit to activate an alarm condition e Whether the internal buzzer is activated during an alarm condition Calibur DSR 1000eZ 3 2 Menu button Time Date Alarms Timer Settings Record Settings Display Settings Archive Setup Advanced Menu About DSR 1000eZ Teletext Alarm Alarm Buzzer CANCEL OK Set Time Set Date Set Time Set Date e Whether an alarm condition will be activated when the Hardwire Alarm Enable Disable Enable 0150 0238A a Main Menu gt Timer Settings START 16 07 09 14 02 This menu allows the user to STOP program a timed recorded event Use this menu to specify e The date or days on which the recording will occur 31 SAT MON FRI SAT SUN MON SUN e The start and stop time e The record speed e The record quality e Wh
3. To Save the changes and Exit the menu Use the Jog to select OK then press the Enter button OR 5 To Exit the menu without making changes Use the Jog to select CANCEL then press the Enter button a Main Menu gt Time Date Set Date To set the Date Date Setup 1 Press the Enter button The highlighting will move to the row of numbers 2 Enter the date in Months Days Years Day of the Week will update automatically Use the Jog to change the values Use the Shuttle to navigate among the three fields 12 17 00 SUN CANCEL OK Press the Enter button to confirm the selection To Save the changes and Exit the menu Use the Jog to select OK then press the Enter button OR 5 To Exit the menu without making changes Use the Jog to select CANCEL then press the Enter button 4 2 Main Menu Alarms Use this menu to specify e Whether an alarm condition will be activated when the Hardwire Alarm X31 unit detects a signal on the Alarm In connection Teletext Alarm Disable e Whether a teletext alarm signal generated by a Alam Sulzer SS multiplexer or other device will cause the unit to CANCEL OK activate an alarm condition e Whether the internal buzzer is activated during an alarm condition A feature unique to the DSR 1000eZ is its ability to detect alarms via teletext provided within the video signal Standard Time Lapse VCRs can only detect an alarm if the alarm ou
4. Connections Ethernet Port Optional Composite Video In BNC connector See caution below Audio Video 0150 0238A 8 1 Calibur DSR 1000eZ On screen Video Indicators Archive Status Pause Rewind End of Data Play Start of Data Fast Forward Record Capacity Time and Date Last Alarm Reverse Play Video Loss Audio Record Speed Playback Speed Part Numbers Accessories PCB 0900 0127 User Manual 0150 0238 Archiving Addendum 0150 0145 WaveReader Software CD Optional 0151 0005 WaveReader Software Manual Optional 0150 0143 All specifications are subject to change without notice GE Interlogix believes all specifications are correct but no liability is assumed for omissions or errors Calibur DSR 1000eZ 8 2 0150 0238A 9 WARRANTY AND SERVICE 9 1 Factory Service Warning Do not open the top cover or attempt to service the unit as this may expose you to dangerous voltages and other hazards Programmer maintenance of this unit is limited to external cleaning and inspection Refer all servicing to qualified personnel If the unit requires factory service contact the dealer who supplied the unit to you for the correct procedures on returning the unit to the factory or the nearest factory service center If the dealer is not available contact the manufacturer of the unit as detailed below and request a Return Material Authorization number RMA The unit s serial number must be provided before a RMA number can b
5. Meaning From the Main menu select TIMER SETTINGS then press the Enter button A Pop up or Pull down menu will appear a Main Menu gt Record Settings gt Normal Record Speed Meaning From the Main menu select RECORD SETTINGS then press the Enter button This opens another menu In this menu select NORMAL RECORD SPEED then press the Enter button A Pop up or Pull down menu will appear Pull down Menus Pull down menus are the top level menus Make a selection in a Pull down menu to enter the appropriate sub menu typically a Pop up menu Changes to the unit s parameters are usually made in Pop up menus To exit a Pull down menu press the Menu button Pop up Menus Pop up menus usually have a parameter or several parameters from which the user can make a selection or change the value Use the Shuttle to select a new parameter use the Jog to change the value of that parameter To Save changes and Exit the menu Select OK the press the Enter O button ENTER Menu button To Exit the menu without making changes Press the Menu button or select CANCEL then press the Enter button In some boxes items are highlighted on the screen They are represented in this manual as follows Not highlighted Highlighted TIME DATE ALARMS 0150 0238A 3 1 Calibur DSR 1000eZ Entering the Main menu Enter the Main menu by pressing the Menu button The Main menu will appear on the primary monitor
6. can be verified by opening the About DSR 1000eZ box and checking the date and checksum of the upgrade firmware 0150 0238A 5 9 Calibur DSR 1000eZ 6 RS 232 REMOTE PROTOCOL The RS 232 protocol command structure uses Start of Text S and End of Text E characters to identify the beginning and end of command sequences The DSR 1000eZ supports the following command sequences ASCII Command String ae NC sse Pam SE Ss www 1 sawe esoe mew INC ann O amm SAU asss Meu 1 menes neen mw mE een Note All byte values shown in hexadecimal 0150 0238A 6 1 Calibur DSR 1000eZ Setting the Clock The following table shows the command sequence for setting the clock Value Value This gray cells in the Value row of this table indicate the correct positions for each byte of data in the command string Place the hexadecimal value of the desired ASCII character into the command string Enter a two digit value for the Year Month Day Hour and Minute into the command string Each digit is a separate byte Use the last two digits of the year for the year value For example 2001 is entered as 01 Time is always designated in Military Time Example In this example 14 39 on December 25 2000 is used to demonstrate the Set Clock Command String ASCII Character of Hex Value entered into desired Value command string Year Character 1 30 Year Character 2 30 Month Chara
7. reached the unit displays an on screen message indicating that the disk is full and the unit has stopped recording User must acknowledge the on screen message by pressing the Enter button e Unit will not record over previously Unit Stops recorded data To continue Recording when this Physical Start recording the data must be erased polis teach Bui csi SEET or deleted in the Advanced gt Disk Maintenance menu No Overwrite Mode 0150 0238A 5 1 Calibur DSR 1000eZ a Advanced Menu Disk Overwrite Mode Overwrite Once Functions of Overwrite Once mode e Recording always starts at end of last recording New recorded data e The unit overwrites all previously recorded data e Recording stops before the unit overwrites any of the new recorded data data from the current record session e When the end of the disk is reached the unit displays an on screen message indicating that the disk is full and the unit has stopped Physical recording User must acknowledge SE Disk the on screen message by pressing s the Enter button Unit Stops Recording when this point is reached Overwrite Once Mode e The unit will continue recording again when the user presses the Record button a Advanced Menu Disk Overwrite Mode Continuous Overwrite Functions of Continuous Overwrite mode e Recording always starts at end of last recording e The unit overwrites all previously recorded data e
8. this message box will appear Press the Enter button to acknowledge the message and S complete the deleting process Archive medium erased 4 7 Main Menu gt Advanced Menu To access the Advanced menu 1 Select ADVANCED MENU from the Main menu then press the Enter button The Password Box will Please Enter The Password appear o 2 Enter the Advanced menu password Use the Jog to select a character then use the Enter button to complete the selection and move to the next character 3 Pressing the Enter button on the last character will complete the password selection and the unit will display the Advanced menu 0150 0238A 4 13 Calibur DSR 1000eZ 5 INSTALLER PROGRAMMING For security reasons a password is provided to limit access to the Advanced menu For instructions about entering the Advanced menu see section 4 7 Main Menu gt Advanced Menu on page 4 13 5 1 Advanced Menu Disk Overwrite Mode Use this menu to specify how the unit will handle disk overwrite Select Mode issues once the hard disk becomes full The unit handles disk overwrite issues in three ways e No Overwrite Continuous Overwrite e Overwrite Once Continuous Overwrite a Advanced Menu Disk Overwrite Mode No Overwrite Functions of No Overwrite mode e Recording always starts at end of last recording e _ Recording stops when end of disk is reached when disk is full e When the end of the disk is
9. while Archiving or transmitting data via the Ethernet Ethernet option only A simple on screen menu system Includes WaveReader software for viewing Live or Recorded images on a PC Ethernet option only Timed recording Audio Recording Audio option only Programmable Auto Delete Mode 1 3 Unpacking Check the package and contents for visible damage If any components are missing or damaged contact the supplier immediately Do not attempt to use the unit If for any reason they must be returned the contents must be shipped in the original packaging Package Contents The DSR 1000eZ unit Accessories PCB The DSR 1000eZ user manual WaveReader software with User Manual Ethernet option only Archiving Addendum 0150 0238A 1 1 Calibur DSR 1000eZ 1 4 Installation Environment Power Ensure that the site s AC power is stable and within the rated voltage of the external power supply If the site s AC power is likely to have spikes or power dips use power line conditioning or an Uninterruptable Power Supply UPS Ventilation Install the unit in a well ventilated area Take note of the locations of the cooling vents in the unit s enclosure and ensure that they are not obstructed Temperature Observe the unit s ambient temperature specifications when choosing a location space Extremes of heat or cold beyond the specified operating temperature limits may cause the unit to fail Do not install the unit on top of ot
10. ANCEL 2 Use the Jog to increase or decrease to saturation 3 To Save the changes and Exit the menu Use the Shuttle to select OK then press the Enter button OR 4 To Exit the menu without making changes Use the Shuttle to select CANCEL then press the Enter button 5 8 Advanced Menu gt Front Panel Lock Use this menu to Lock or Unlock the front panel Unlock Keyboard Use the Jog to select UNLOCK KEYBOARD Or LOCK KEYBOARD Lock Keyboard Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes 0150 0238A 5 7 Calibur DSR 1000eZ 5 9 Advanced Menu gt Factory Settings Use this menu to enter the Factory Password and restore the unit to the factory defaults Please Enter The Factory Password Use the Jog to select a character then use the e Ze ee Enter button to complete the selection and move to Y the next character Pressing the Enter button on the last character will complete the password selection and return the unit to the factory default configuration 5 10 Advanced Menu gt Change Password Password Enter A New Password Use the Jog to select a character then use the Zeen Enter button to complete the selection and move to ai the next character Pressing the Enter button on the last character will open the Confirmation Box Re enter the New password Confirmation Box Pressing the Enter button on
11. CED MENU from the Main menu then press the Enter button The Password Box will appear 2 Enter the Advanced menu password Use the Jog to select a character then use the Enter button to complete the selection and move to the next character 3 Pressing the Enter button on the last character will complete the password selection and the unit will display the Advanced menu a Main Menu About DSR 1000eZ Please Enter The Password Use this menu to display information about the DSR 1000eZ Select Main Menu gt About DSR 1000eZ to display the About DSR 1000eZ screen Serial Number Software Version D406 T72F 219019 2 00 Sep 03 2002 16 40 18 41173C6B 1 00 161 99 GB Software Date Software Checksum Boot Code Ver Disk Size The Advanced Menu For security reasons a password is provided to limit access to the Advanced menu For instructions about entering the Advanced menu see Main Menu gt Advanced Menu on the previous page The Advanced menu provides access to all of the installer programmable options Each sub section of the Advanced menu is described briefly in this section For complete information about installer programming in the Advanced menu see section 5 Calibur DSR 1000eZ Ethernet information will not be displayed unless the DSR 1000eZ is an ethernet supplied model Disk Overwrite Mode Disk Maintenance Audio Record Setting Auto Delete Mode Communications Multiple
12. ERASE then press the Enter button The Erase Disk Warning box will appear Select CANCEL to return to the previous menu or OK to continue All data will be permanently erased Do You want to continue CANCEL OK Erasing Disk To stop the erasing process select CANCEL by pressing the Enter button CANCEL Data that was erased before CANCEL was selected will remain deleted permanently 5 3 Advanced Menu Audio Record Setting OFF G 711 64kb s Use this menu to e Select Off and Disable the audio recording capability e Select G 711 and Enable the audio recording capability Audio units only 0150 0238A 5 3 Calibur DSR 1000eZ 5 4 Advanced Menu gt Auto Delete Mode Configuring the unit with the Auto Delete mode from 7 to 99 days prevents the unit from displaying or archiving any data that is more than the selected number of days old This feature may be required by law in some jurisdictions please consult with the local authorities Use the Jog to select from 7 99 Days or OFF Press the Enter button to implement the selection If the selection is altered from what was previously selected the confirmation menu will appear Rotate the Shuttle to select Yes or NO ADM Setting ADM will change Are you sure Yes 5 5 Advanced Menu gt Communications Use thus menu to specify Baud Rate e The data transfer rate for the RS 232 serial port Ethernet Settings e The units Ethe
13. POWER ALARM DSR 1000eZ O 5 amp RECORD REVERSE PLAY STOP PLAY PAUSE SEARCH REC PLAY SPEED OJIODMO Calibur by AWA Calibur DSR 1000eZ Single Channel Color Digital Video Recorder User Manual WARNING To prevent fire and electric shock do not expose this product to rain or moisture The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product CAUTION To prevent electric shock do not remove cover No user serviceable components are inside Refer servicing to qualified service personnel CAUTION Lithium Battery ATTENTION Danger of explosion if battery is This product contains a recyclable lithium battery incorrectly replaced Replace only It may be illegal to dispose of this battery with the same or equivalent type improperly under local state or federal laws recommended by the Check with your local waste management officials manufacturer for disposal and recycling options CAUTION Electrostatic Sensitive Device Use proper CMOS and MOSFET handing precautions including ap
14. Press the Menu button to exit the menu without making changes 0150 0238A 4 7 Calibur DSR 1000eZ a Main Menu gt Display Settings Record Playback Speed To display the Record Playback Speed near the upper right hand corner of the primary monitor select On Use the Jog to select On or Off Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes 4 6 Main Menu gt Archive Setup Use this menu to Selective archive e Select data to be archived and begin archiving process E Background archive e Restore data from archive device Archive Overwrite Mode e Enable background archiving Erase Archive Medium e _ Specify how the unit will handle overwrite issues when the archive medium becomes full e Erase the archived data a Main Menu gt Archive Setup gt Selective Archive The Selective Archive feature allows the user to archive recorded data from the hard disk onto a CD DAT AIT RAID or DVSe See the Archiving Addendum for details about using archive devices The Archive Search Filters menu allows the user to search the hard disk for recorded events such as an alarm condition or a previous recording session then select events to be archived for later viewing For example each time Record mode is activated it is considered a separate recording session Use this menu to specify Archive Search Filters e The Start and Stop dat
15. SS Y a Advanced Menu gt Change Password Use this menu to change the Advanced Menu Password Enter a new Password B 0150 0238A 3 7 Calibur DSR 1000eZ 4 OPERATOR PROGRAMMING 4 1 Main Menu gt Time Date Use this menu to specify e The time format 12 or 24 hours e The date format MM DD YY DD MM YY or YY MM DD e The time e The date a Main Menu gt Time Date gt Set Time Format To set the Time format use the Jog to select the desired Time format Time Format Setup Format the time as either e 12 HOUR Select Format 24 HOUR Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes a Main Menu Time Date Set Date Format To set the Date format use the Jog to select the desired Date format Format the Date as either e DD MM YY Select Format MM DD YY e YY MM DD Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes 0150 0238A 4 1 Calibur DSR 1000eZ a Main Menu gt Time Date Set Time 1 With HH MM Ss highlighted press the Enter button The highlighting will move to the row of numbers 03 05 53 2 Enter the time in Hours Minutes and Seconds Use the Jog to change the values Use the Shuttle to navigate among the three fields CANCEL OK Press the Enter button to confirm the selection
16. Theunit overwrites new recorded data data from the current record session e Unit never stops recording e Record Capacity display will not count down Unit records over all recorded data gt Continuous Overwrite Mode 5 2 Advanced Menu gt Disk Maintenance The user can have previously recorded information Delete Undelete Erase e Deleted with the possibility of restoring it e Undeleted restored if it has not yet been overwritten e Erased removed with no possibility of restoring it Calibur DSR 1000eZ 5 2 0150 0238A a Advanced Menu Disk Maintenance Delete To begin deleting the disk use the Jog to select DELETE then press the Enter button The Deleting Disk menu will appear The unit will begin deleting the oldest recorded information immediately To stop the delete process select CANCEL by pressing the Enter SE button Data that was deleted before CANCEL was selected will remain deleted unless UNDELETE s selected a Advanced Menu Disk Maintenance gt Undelete To restore information that was previously deleted use the Jog to select UNDELETE then press the Enter button MW A 1 To stop the restore process select CANCEL by pressing the Enter button CANCEL a Advanced Menu Disk Maintenance Erase Caution Erasing the disk removes recorded data without the possibility of restoring it To begin erasing the disk use the Jog to select
17. V active for the duration of the alarm event Low Ground Current Out 50mA Max Short Circuit Protected Low for duration of alarm Record Start In Record Start In will place the unit in Record mode when Input Active Low TTL w pull ups activated Compatible with the Disk End Out signal from a or Normally Open Relay second unit High 5V 12V tolerant Low Ground Minimum Duration 0 5 Seconds Alarm Record Reset This feature is for future development and has not yet been implemented Calibur DSR 1000eZ 1 6 0150 0238A VEXT Pulse Out The Video External Pulse connection VEXT simplifies Output Active Low multiplexer operation by automatically synchronizing the High 5V Multiplexer and the DSR 1000eZ Low Ground 0 8V Max The DSR 1000eZ sends a VEXT pulse to the Multiplexer Geier Een indicating that it is ready to record the next image The l Multiplexer responds by sending the next image to the Video BE Input on the DSR 1000eZ L rete The VEXT connection is especially beneficial for units configured with dual record speeds Normal and Alarm Use of the VEXT connection is Highly Recommended when connecting the unit to a multiplexer Error Out The Error Out signal is activated when the unit experiences any Output Open Collector operational or internal error High Transistor Off Low Transistor On Active When On Current Out 10mA Max Minimum Duration 0 5 Seconds Videoloss Out The Vid
18. anges Use the Jog to select CANCEL then press the Enter button 1 10 Setting the Alarms a Main Menu gt Alarms Use this menu to speci Hardwire Alarm sais e Whether an alarm condition will be activated when the unit detects a signal on the Alarm In connection Teletext Alarm Disable e Whether a teletext alarm signal generated by a Kee multiplexer or other device will cause the unit to CANCEL OK activate an alarm condition e Whether the internal buzzer is activated during an alarm condition 1 Use the Shuttle to navigate among the fields EE EE EE EE 2 Use the Jog to change the values of the highlighted Teletext Alarm Disable fields Alarm Buzzer 3 To Save the changes and Exit the menu Use the CANCEL Jog to select OK then press the Enter button OR 4 To Exit the menu without making changes Use the Jog to select CANCEL then press the Enter button 0150 0238A 1 9 Calibur DSR 1000eZ Calibur DSR 1000eZ 1 10 0150 0238A 2 USER OPERATIONS 2 1 Recording To begin recording press the Record button RECORD will be indicated for RECORD three seconds near the upper left hand corner of the primary monitor The O unit always starts recording at the end of the previously recorded data Recording will continue until e Another mode is selected Play mode Reverse Play or Stop mode Record button e The disk is full In No Overwrite and Overwrite Once modes See section 5 1 Advanc
19. corded images on a PC via the Ethernet Power Connector Connect 12 Volt DC external power supply SCSI Port For connecting an SCSI compatible archive device Audio In Optional RCA jack 315mV 40k Ohms Unbalanced Audio Out Optional RCA jack 315mV 600 Ohms Unbalanced Video In Composite video input with BNC style connector 0150 0238A 1 3 Calibur DSR 1000eZ Video Out Composite video output with BNC style connector Ethernet Port Ethernet models only The cable connection configuration depends on your Wire Type CAT5 network configuration e Fora DSR 1000eZ that connects directly to a Connector Type RJ 45 Hub use a Straight Through connection Max Cable Length 100 feet 30 5 meters e Fora DSR 1000eZ that connects directly to a Minimum Cable Length 6 feet 1 8 meters PC use a Cross Over connection Hub Wiring Configuration Straight Through Consult with your MIS personnel for the specific type PC Wiring Configuration Cross Over of configuration See section 5 5 Advanced Menu gt Communications for information about configuring the ethernet settings in the menu system RJ 45 Pin Configuration for Ethernet Port Not Connected RX Not Connected Not Connected RJ 45 Connector on Back Panel Power Connector Power Supply Input Power Supply Output Voltage 120 to 240 Volt AC Voltage 12 Volt DC Tolerance 10 Power 35 Watt Frequency 50 to 60 Hz Connector 2 1mm barrel Center Pos
20. cter 1 31 Month Character 2 32 Day Character 1 32 Day Character 2 35 Hour Character 1 31 Hour Character 2 34 Minute Character 1 3 33 Minute Character 2 Value Calibur DSR 1000eZ 6 2 0150 0238A ASCII Status Request Messages ASCII String Bytes in Hexadecimal Model Name Request S MLN E 02 4D 4C 4E 03 Software Version Number Request S SVN E 02 73 77 4E 03 Record Mode Status Request S RMS E 02 52 4D 73 03 Stop Mode Status Request S SMS E 02 73 4D 73 03 ASCII Status Response Messages Record Mode Status Response Stop Mode Status Response S SMS 3 E Playing and End of Disk 0150 0238A 6 3 Calibur DSR 1000eZ 7 FACTORY DEFAULTS Date Format MM DD YY Normal Record Speed 60 pictures per seconds NTSC or 50 pps Pal Alarm Record Speed 60 pictures per seconds NTSC or 50 pps Pal Disk Overwrite Mode Continuous Overwrite Archive Overwrite Mode Not currently implemented Auto Delete Mode Off Background Archive Mode Off Front Panel Locked Off Display Current Time and Date Off Display Record Capacity Off Display Last Alarm Off Display Archive Status Off Display Playback Time and Date Off Audio Record Setting Off 0150 0238A 7 1 Calibur DSR 1000eZ 8 TECHNICAL SPECIFICATIONS General Operating Temperature Range Relative Humidity Range Non Condensing Operating 10 to 80 Storage 10 to 95 Dimensions Inches 8 6 x 12 x 2 2 MM 204 x 307 x 56 Weight 10 Ibs 4 5 kg
21. d button Press this button to playback video at the normal record speed Pause button Press this button to pause playback Search button Press this button to enter the Search Filters menu Increase and Decrease Record Speed buttons Press these buttons to increase or decrease the Record or Playback speed Combination Menu and Enter button Press the lower half of the button the Menu button to enter the Menu system Also used to move to higher level menus while in the menu system OR Press the upper half of the button the Enter button to make or confirm a selection in the menu system Power On Indicator and Alarm Indicator Indicates power and an alarm indication when their respective LED s are lit Jog Shuttle The Jog the inner of the two dials is used for single frame advance while in Pause mode it is also used to change the value of a parameter while in the menu system The Shuttle the outer of the two dials is used to Fast Forward and Rewind while in the Play mode 1 7 Back Panel Connections oa FY 7 Figure 1 3 Back Panel VIDEO UO Port For connecting peripheral devices such as alarm devices alarm relays or the VEXT connection RS 232 Serial Port Serial port for Flash Upgrading of software Also for external control of unit Ethernet Port Optional For viewing Live or Re
22. d image Calibur DSR 1000eZ 5 6 None Kalatel Robot DM Philips Pelco Sanyo Philips REO Navco ATV ATV QSP Vista VLM QSI 1700 Diebold Brightness Contrast Saturation 0150 0238A a Advanced Menu gt Adjust Picture Adjust Brightness Use this menu to increase or decrease the brightness of the image Adjust Brightness 1 Use the Shuttle to navigate to the numbers 2 Use the Jog to increase or decrease to brightness Mw oui 3 To Save the changes and Exit the menu Use the Shuttle to CANCEL select OK then press the Enter button OR 4 To Exit the menu without making changes Use the Shuttle to select CANCEL then press the Enter button a Advanced Menu gt Adjust Picture gt Adjust Contrast Use this menu to increase or decrease the contrast of the image Adjust Contrast 1 Use the Shuttle to navigate to the numbers 2 Use the Jog to increase or decrease to contrast Mw mi 3 To Save the changes and Exit the menu Use the Shuttle to CANCEL select OK then press the Enter button OR 4 To Exit the menu without making changes Use the Shuttle to select CANCEL then press the Enter button a Advanced Menu gt Adjust Picture gt Adjust Saturation Use this menu to increase or decrease the saturation of the image Adjust Saturation Saturation refers to the amount of color displayed in the image 1 Use the Shuttle to navigate to the numbers CCU C
23. e Enter button at any time to exit Edit mode Selecting Cameras to Search 1 Using the Shuttle to navigate highlight the CAMERA parameter then press the Enter button The unit will enter Edit mode Use the Shuttle to navigate among the different cameras Use the Jog to select a camera or cameras by placing an X in the check box Press the Enter button at any time to exit Edit mode Searching for Recorded Alarms 1 Using the Shuttle to navigate highlight the ALARM parameter then press the Enter button The unit will enter Edit mode 2 Use the Jog to activate the alarms search by placing an X in the check box 3 Press the Enter button at any time to exit Edit mode 0150 0238A 4 9 Calibur DSR 1000eZ Starting the Search Using the Shuttle to navigate highlight the START SEARCH parameter then press the Enter button The Archive Search Results menu will appear Archive Search Results Start Date Start Time Size MB 11 28 2000 19725274 26842 11 29 2000 09 35 20 2062 1 11 29 2000 10 00 04 278 x 11 29 2000 10 03 25 66 x Selected 383 MB Available on Target Medium 652 MB ENTER to play SEARCH to archive Selecting from the Archive Search Results 1 Use the Jog to navigate highlighting the recorded event you wish to select 2 Use the Shuttle to select a recorded event by placing an x in the check box Starting the Archive Process To begin archiving press the Search butto
24. e issued Units returned to the factory for service must have freight and insurance prepaid and must show the RMA number clearly on all shipping documents The failure symptoms must be clearly described by the operator and enclosed with the unit together with a copy of the original suppliers invoice Failure to comply with these instructions will delay service of the unit and may result in the unit not being accepted by the Repair Center Factory Address GE Interlogix Attention Repair Center 3197 C Airport Loop Drive Costa Mesa CA 92626 United States of America Telephone 800 343 3358 7 00 AM to 4 30 PM Pacific Time In Oregon 541 754 9133 Fax 541 754 7162 24 hours a day For warranty information see the following page 0150 0238A 9 1 Calibur DSR 1000eZ 9 2 Warranty and Return Information GE Interlogix warrants all of its equipment for three years from the date of purchase This warranty covers any defects in materials and workmanship Equipment failures that are due to improper installation modification abuse or acts of nature will not be covered by this warranty The repair department will evaluate all equipment returned for repair to determine warranty coverage The Tech Support Manager will resolve any questions that may arise during evaluation to make a final determination Note The three year warranty does not apply to the following products MobileView and the monitor CRT which carry a 12 month warranty from
25. e of Start Stop the search DATE 12 25 00 01 01 01 e The Start and Stop time of MM DD YY MM DD YY the search Start Stop e Which cameras to search TIME 11 11 21 12 34 34 exclusively e Tosearch for recorded n 2 8g 4 5G y 8 alarms CAMERA 1E 1E 1E JI JI 1I 1 CANCEL START SEARCH Searching for All Recorded Events Using the Shuttle to navigate highlight START SEARCH then press the Enter button The Archive Search Results window will appear For information about selecting a recorded event see Selecting from the Archive Search Results in this section Calibur DSR 1000eZ 4 8 0150 0238A Specifying Search Parameters Selecting a Start and Stop Date 1 Using the Shuttle to navigate highlight the DATE parameter then press the Enter button The unit will enter Edit mode Use the Jog to change the start and stop date values Use the Shuttle to navigate among the different parameters To activate the start or stop date parameter use the Jog to place an X in the check box Press the Enter button at any time to exit Edit mode Selecting a Start and Stop Time 1 Using the Shuttle to navigate highlight the TIME parameter then press the Enter button The unit will enter Edit mode Use the Jog to change the start and stop time values Use the Shuttle to navigate among the different parameters To activate the start or stop time parameter use the Jog to place an X in the check box Press th
26. ecify Baud Rate The data transfer rate for the RS 232 serial port FA Sisa Modem Settings e The units Ethernet network connection settings Ethernet option only e The Modem connection settings a Advanced Menu gt Multiplexer Format The DSR 1000eZ is compatible with several different brands of multiplexers Use None this menu to specify the Playback format of the multiplexer If the unit is not Kalatel connected to a multiplexer select NONE Robot Note The DSR 1000eZ can auto detect the camera type connected NTSC or DM PAL The Navco multiplexer is only available on NTSC units Certain menu items may be grayed out and unavailable under certain circumstances The Vista VLM is grayed on the menu to the right because the DSR 1000eZ has auto detected that an NTSC input signal is attached Sanyo Philips REO Navco ATV Philips Pelco ATV QSP Vista VLM QSI 1700 Diebold a Advanced Menu gt Adjust Picture Use this menu to specify the Brightness Contrast and Saturation of the video input Brightness Adjustments made to the video input will alter the recorded image Contrast Saturation Calibur DSR 1000eZ 3 6 0150 0238A a Advanced Menu Front Panel Lock Use this menu to Lock or Unlock the front panel Unlock Keyboard Lock Keyboard a Advanced Menu gt Factory Settings Use this menu to enter the Factory Password and restore the unit to the factory defaults Please enter the Factory Password ME
27. ed Menu gt Disk Overwrite Mode on page 5 1 for details regarding Disk Overwrite modes Normal Recording The unit records at the normal record speed until an alarm condition is detected A The normal record speed is indicated on the monitor if the display option is enabled and can be altered using the Up Down Record Speed buttons or in the menu REC PLAY system SPEED For information about altering the normal record speed from the menu system see V Main Menu gt Record Settings gt Normal Record Speed on page 4 5 of the Operator Programming section of this manual An Speed uttons The normal record speed can be altered while the unit is recording The unit will continue recording while the menu system is active Alarm Recording When an alarm condition is detected the unit automatically switches to the 40 alarm record speed The alarm condition is indicated in several ways ALARM e With the word ALARM displayed on the primary monitor near the Alarm Indicator upper left hand corner of the screen e With the internal buzzer if activated in the menu system For information about activating the internal buzzer during alarms see Main Menu Alarms on page 4 2 of the Operator programming section of this manual e Byan external device connected to the alarm output of the unit if the unit is installed that way The alarm record speed cannot be changed using the Up Down Record Speed buttons on the front panel The alarm rec
28. ely using the WaveReader software When the Ethernet session ends the unit re enables the RS 232 and RS 485 communications and unlocks the front panel Playback stops when an Ethernet session is started Playback will not be re activated automatically when the Ethernet session ends a Advanced Menu gt Communications gt Modem Settings A Modem session is an active modem connection between a PC and the unit with the user viewing live camera images or accessing data stored on the hard disk selected this warning box will appear Warning Machine will reset if any values change Select OK to continue OK The default modem string shown below is for use with Hayes Accura 56k Diamond Supra Express 56k and 5686 US Robotics modems in their default conditions Consult with the modem manual before attempting to make any changes It is strongly recommended that the modem initialization string only be modified by a qualified technician Modem Settings Modem Status gi Modem Init String ATARI IAN AENA wa QABCDEFGHIJKLMNOPORSTUVXXYZ X Default Modem String CANCEL OK 0150 0238A 5 5 Calibur DSR 1000eZ Set the Modem status to Enable to allow access of the DSR 1000eZ by Mode 1 With the Modem Init String highlighted press the Enter button to enter the Edit mode The character bank will appear in the center of the menu Rotate the Shuttle to navigate the Modem Init String Rotate the Jog to select a charact
29. en press the Enter button The Search Results window will appear For information about selecting a recorded event see Selecting from the Search Results in this section 2 4 Specifying Search Parameters Selecting a Start and Stop Date 1 Using the Shuttle to navigate highlight the DATE parameter then press the Enter button The unit will enter Edit mode 2 Use the Jog to change the start and stop date values Use the Shuttle to navigate among the different parameters To activate the start or stop date parameter use the Jog to place an X in the check box Press the Enter button at any time to exit Edit mode Selecting a Start and Stop Time 1 Using the Shuttle to navigate highlight the TIME parameter then press the Enter button The unit will enter Edit mode 2 Use the Jog to change the start and stop time values Use the Shuttle to navigate among the different parameters To activate the start or stop time parameter use the Jog to place an X in the check box Press the Enter button at any time to exit Edit mode Selecting Cameras to Search 1 Using the Shuttle to navigate highlight the CAMERA parameter then press the Enter button The unit will enter Edit mode 2 Use the Shuttle to navigate among the different cameras 3 Use the Jog to select a camera or cameras by placing an X in the check box 4 Press the Enter button at any time to exit Edit mode Calibur DSR 1000eZ 2 4 0150 0238A Searching fo
30. eoloss Out signal is activated when the unit experiences Output Open Collector videoloss on the selected video input Composite or SVHS High Transistor Off Low Transistor On Active When On Current Out 10mA Max Minimum Duration 0 5 Seconds In the event of videoloss VIDEOLOSS will be indicated near the upper left hand corner of the primary monitor Disk End Out The Disk End Out is activated when there is 5 minutes of Output Open Collector recording space left on the hard disk It will also be activated if a High Transistor Off DAT or AIT tape archiving device is connected and the tape Low Transistor On end is encountered The DSR 1000eZ must be in Record mode Active When On with Background Archiving ON and set to Continuous Overwrite Current Out 10mA Max mode Minimum Duration 0 5 Seconds 1 9 Setting the Time and Date It is recommended that as a minimum the following menu items be configured before using the unit For detailed information about using the menu system see section 3 0150 0238A 1 7 Calibur DSR 1000eZ a Main Menu gt Time Date Set Time Format To set the Time format use the Jog to select the desired Time format Time Format Setup Format the time as either e 12 HOUR Select Format 24 HOUR Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes a Main Menu gt Time Date Set Date Format T
31. er from the character bank and advance to the next character When finished press the Enter button Rotate the Shuttle to insert the desired character from the character bank into the Modem Init String To save the changes and reboot select OK then press the Enter button The unit will only reboot if changes were made to the Modem Init String To exit the menu without making changes select Cancel then press the Enter button Pressing the Menu button also exits the menu without making changes 5 6 Advanced Menu gt Multiplexer Format The DSR 1000eZ is compatible with several different brands of multiplexers Use this menu to specify the Playback format of the multiplexer If the unit not connected to a multiplexer select NONE Use the Jog to select the Multiplexer format Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes Note The DSR 1000eZ can auto detect the camera type connected NTSC or PAL The Navco multiplexer is only available on NTSC units Certain menu items may be grayed out and unavailable under certain circumstances The Vista VLM is grayed on the menu to the right because the DSR 1000eZ has auto detected that an NTSC input signal is connected 5 7 Advanced Menu gt Adjust Picture Use this menu to specify the Brighiness Contrast and Saturation of the video input Adjustments made to the video input will alter the recorde
32. esponsibility is assumed by GE Interlogix for neither its use nor any infringements of rights of third parties that may result from its use No license is granted by implication or otherwise under any patent or patent rights of GE Interlogix The CALIBUR brand name and product model numbers are the property of GE Interlogix COPYRIGHT 2002 The contents of this manual may not be copied or reproduced in any manner or form without the prior written consent of GE Interlogix 0150 0238A ii Calibur DSR 1000eZ Calibur DSR 1000eZ iv 0150 0238A CONTENTS 1 FEATURES CONNECTIONS AND SETUP oonnccccccoccnccccnnnnnnncrrnnnnnnnnrernnnananennn 1 1 1 1 Product DESEN PWO MA ki kk a ki a kak ki ai ik inca 1 1 12 F amp alures nassen rer 1 1 1 9 UNPACKING soii 1 1 1 4 Installation Environment ccc ooo ee 1 2 1 5 Ed TE 1 2 1 6 Front Panel Controls u nam SEENEN 1 2 1 7 Back Panel Connections 1 3 1 8 Accessories l O Porta 1 5 1 9 Setting the Time and Date seien nra innu nean dana 1 7 1 10 Setting The Aldaia 1 9 2 USER OPERATIONS UU oiim III 2 1 2 4 Recording ki ki kk 2 1 2 2 E O 2 2 2 3 The Search Interface seat a ano oka aie a ke anka ake an ke an Aaaa Naaa iain 2 3 2 4 Specifying Search Parameters cccccccsessseeeeeeeeeeeeeesseeseeeeeeeeeeeeeeeeeeenennees 2 4 3 THE MENU SS E 3 1 4 OPERATOR PROGRAMMING cccocacccconaccconanccnnnanccnnanno
33. ether the event is enabled a Main Menu gt Record Settings Use this menu to specify e The record speed during Normal recording e The record speed when the unit detects an alarm condition e The recorded picture quality a Main Menu gt Display Settings Use this menu to specify what status information will be displayed on the primary monitor Select On or Off for the following items e The current time and date e The remaining amount of time before the hard disk runs out of record space e The Archive Status e The time and date of the last alarm e The current record playback speed e During Playback the time and date the recording was made a Main Menu gt Archive Setup Use this menu to e Select data to be archived and begin archiving process e Restore data from archive device e Enable background archiving e Specify how the unit will handle overwrite issues when the archive medium becomes full e Erase the archived data 0150 0238A SPD pps QUALITY ON OFF EDIT Mode Hit ENTER To Toggle EDIT Mode Normal Record Speed Alarm Record Speed Video Quality Current Time Date Record Capacity Archive Status Last Alarm Record Playback Speed Playback Time Date Selective archive Restore from archive Background archive Archive Overwrite Mode Erase Archive Medium Calibur DSR 1000eZ Main Menu Advanced Menu To access the Advanced menu 1 Select ADVAN
34. her hot equipment Moisture Do not expose the unit to rain or moisture Moisture can damage the internal components Do not install this unit near sources of water Chassis You can place other equipment on top of the unit if it weighs less than 35 pounds 1 5 Passwords Figure 1 1 Passwords Advanced Menu Provides access to the Advances menu for the Yes See page 5 8 3477 ee installer Restores the unit to the A password is provided to limit access to the Advanced menu It is recommended that the default password be changed after installation is complete As a security measure store the password in the administrator s secured files or in a limited access area For instructions on entering the Advanced menu with the password see section 4 7 Main Menu gt Advanced Menu on page 4 13 A password is also provided to return the unit to the factory defaults For instructions on returning the unit to the factory defaults see section 5 8 Advanced Menu gt Factory Settings on page 5 8 1 6 Front Panel Controls Figure 1 2 Front Panel DSR 1000eZ RECORD REVERSE PLAY STOP PLAY PAUSE SEARCH RECIPLAY SPEED OoOdopmo Calibur by CAAT 1 Record button Press this button to begin recording Calibur DSR 1000eZ 1 2 0150 0238A NO pm FP ph 10 Reverse play button Press this button to playback video in reverse at the normal record speed Stop button Press this button to stop Recording or Playback Play Forwar
35. hes automatically depending on the amount of time remaining e Days and Hours e Hours and Minutes e Minutes and Seconds Use the Jog to select ON or OFF Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes a Main Menu gt Display Settings gt Archive Status To display the archive status near the upper center of the screen on the primary monitor select ON The unit will display either ARCHIVE NOT CONNECTED ARCHIVE READY ARCHIVE NOT READY Use the Jog to select ON or OFF Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes a Main Menu gt Display Settings Last Alarm To display the time and date of the last alarm near the upper right hand corner of the primary monitor select On The unit will display NONE if there is no previous record of an alarm Use the Jog to select On or Off Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes a Main Menu gt Display Settings Playback Time Date To display the time and date the recording was made during playback select On The data is displayed near the upper right hand corner of the screen Use the Jog to select On or Off Press the Enter button to confirm the selection and exit the menu OR
36. itive SCSI Port The unit is equipped with a SCSI port for Connector 50 Pin High Density SCSI 2 connecting external archive devices The unit only supports a single SCSI device The SCSI ID must Gender on unit Female be set to 0 Compatible devices DAT AIT CD R CD RW The SCSI bus must be terminated otherwise the Autoloader Support No system will not operate properly SCSI ID 0 Additional menu setup may be necessary to configure archive device See section 4 6 Main Menu Archive Setup Calibur DSR 1000eZ 1 4 0150 0238A RS 232 Serial Port Use a Null Modem cable when connecting to a Connector Type DB 9 PC When connecting to a multiplexer it may be necessary to construct a cable using the pin out documentation of the MUX as a guide See Cable Required Connected to PC Null Modem the pin out configuration for the DSR 1000eZ below Gender on unit Male Cable Required Connected to Multiplexer Variable depending on pin out configuration of DB 9 Pin Configuration for Serial Port DB 9 Connector on Back Panel Video Input and Output The unit is equipped with a Composite video input Composite Input 75 Ohm BNC connector and output The video input is auto terminating Composite Output 75 Ohm BNC connector Composite Looping Yes while unit is On or Off 1 8 Accessories I O Port The back panel of the unit is equipped with an Accessories Port DB 9 ACCESSORIES style connecto
37. m 45 days to 1 year from purchase GE Interlogix will replace the product with refurbished equipment e From 1 year to 3 years from purchase the product must be sent in for repair Advance replacements will be sent for a fee of 100 If you have questions about this policy please contact the GE Interlogix RMA Department at 800 469 1676 Calibur DSR 1000eZ 9 2 0150 0238A
38. n O Reverse playback is indicated e AS REVERSE PLAY near the upper left hand corner of the primary monitor for three seconds m Reverse play If there is only one recording session on the hard disk the unit will indicate START button OF DATA on the primary monitor Playback Speed The unit will playback the data at the rate it was recorded The user can alter the 2 playback speed using the Up Down Record Speed buttons Altering the playback speed overrides any change in playback speed that would jad occur due to an alarm condition in the playback To clear the override press the Stop button then press the Play button to resume playback at the speed the data V was recorded Record Speed buttons Calibur DSR 1000eZ 2 2 0150 0238A Fast Forward During playback rotate the Shuttle clockwise to view the data at a Higher than normal rate Increasing the amount of rotation increases the rate of playback Fast Forward is indicated e AS FAST FORWARD near the upper left hand corner of the primary monitor for three seconds Rewind During playback rotate the Shuttle counter clockwise to view the data in reverse at a Higher than normal rate Increasing the amount of rotation increases the rate of playback Rewind is indicated e AS REWIND near the upper left hand corner of the primary monitor for three seconds Pause During playback press the Pause button to pause playback and display a single frame on screen Pa
39. n The Archiving progress bar will appear Press the Enter button to cancel archiving at any time CC CANCEL When the unit is finished archiving this message box will appear Press the Enter button to acknowledge the message and complete en the archiving process Archiving completed a Main Menu gt Archive Setup gt Restore From Archive The DSR 1000eZ supports data restoration to the hard disk from an archive device Data may be restored from a DAT AIT RAID or DVSe See the Archiving Addendum for details about using archive devices The DSR 1000eZ does allow the user to search the archived data for recorded events such as an alarm condition or a previous recording session Calibur DSR 1000eZ 4 10 0150 0238A Use this to specify Restore Search Filters e The Start and Stop date of Start Stop the search DATE 12 25 00 01 01 01 e The Start and Stop time of MM DD YY MM DD YY the search BESTE Stop e Which cameras to search TIME 11 11 21 12 34 34 exclusively e To search for recorded 4 we sy AN 5 CATAS alarms CAMERA 1E 1E 1E JI JI 1I 1 CANCEL START SEARCH Searching for All Recorded Events Using the Shuttle to navigate highlight START SEARCH then press the Enter button The Restore Search Results window will appear Specifying Search Parameters Selecting a Start and Stop Date 1 Using the Shuttle to navigate highlight the DATE parameter then press the Enter button The u
40. nananronanancrnananennnaarananana 4 1 4 1 Main Menu gt TmeiDate een 4 1 4 2 Main Menu gt Alarm naeh 4 2 4 3 Main Menu gt Timer SettiMQS ccoommmmonnconocccnnnnnnccccnacnncnonnnnnnnnnnnccnnr rra 4 3 4 4 Main Menu gt Record Settings eecceeeeeeseeeeseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeneees 4 5 4 5 Main Menu gt Display Settings uuuuuuuuuun0000000nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 4 6 4 6 Main Menu Archive Setup ooo ee nn 4 8 4 7 Main Menu gt Advanced Menu cceeeeeceeeeeeeeseneeeeeeeeeseneneeeneeeeeeeeeeenees 4 13 5 INSTALLER PROGRAMMING ccoonccocaccnonccnnnccnnnccnnnrnnanrrnanrrnanrrnanrrnanrrnanernanenns 5 1 5 1 Advanced Menu gt Disk Overwrite Mode 5 1 5 2 Advanced Menu gt Disk Maintenance Rn 5 2 5 3 Advanced Menu gt Audio Record Setting cooommnnnoncccccncnnnnnnnanaccccnnnnnnnnnnnas 5 3 5 4 Advanced Menu gt Auto Delete Mode nn 5 4 5 5 Advanced Menu Communications eese eese esses ssssus 5 4 5 6 Advanced Menu gt Multiplexer Format eeeeeeeeeeennnn 5 6 5 7 Advanced Menu gt Adjust PiCture ccccccccessseseseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeneees 5 6 5 8 Advanced Menu gt Front Panel Lock sess 5 7 5 9 Advanced Menu gt Factory SettinQS ooccccccccnnnnnnnancccnono
41. nit will enter Edit mode 2 Use the Jog to change the start and stop date values Use the Shuttle to navigate among the different parameters To activate the start or stop date parameter use the Jog to place an X in the check box Press the Enter button at any time to exit Edit mode Selecting a Start and Stop Time 1 Using the Shuttle to navigate highlight the TIME parameter then press the Enter button The unit will enter Edit mode 2 Use the Jog to change the start and stop time values Use the Shuttle to navigate among the different parameters To activate the start or stop time parameter use the Jog to place an X in the check box Press the Enter button at any time to exit Edit mode Selecting Cameras to Search 1 Using the Shuttle to navigate highlight the CAMERA parameter then press the Enter button The unit will enter Edit mode Use the Shuttle to navigate among the different cameras Use the Jog to select a camera or cameras by placing an x in the check box Press the Enter button at any time to exit Edit mode 0150 0238A 4 11 Calibur DSR 1000eZ Searching for Recorded Alarms 1 Using the Shuttle to navigate highlight the ALARM parameter then press the Enter button The unit will enter Edit mode Use the Jog to activate the alarms search by placing an X in the check box Press the Enter button at any time to exit Edit mode Starting the Search Using the Shuttle to navigate highligh
42. nonnnnnnananaccnnnnnnnnnnnnas 5 8 5 10 Advanced Menu gt Change Password eese 5 8 0150 0238A V Calibur DSR 1000eZ o ON Oo 5 11 Advanced Menu gt Firmware Upgrade esee 5 9 RS 232 REMOTE PROTOCOL ME 6 1 EE 7 1 TECHNICAL SPECIFICATIONS cccccccconnnnnnnnnnnonnnnnnnnnnnnnnnnnnnnnnnnnrrnnnnnnnnanananann 8 1 WARRANTY AND SERVICE EE 9 1 9 T OO 9 1 9 2 Warranty and Return Information eese 9 2 0150 0238A Calibur DSR 1000eZ vi 1 FEATURES CONNECTIONS AND SETUP 1 1 Product Description The DSR 1000eZ is a Digital Video Recorder designed to be a direct replacement for a Time Lapse VCR Digital Video Recording allows the user to have continuous recording on a hard disk without the need for replacing or rewinding of videotapes The DSR 1000eZ provides menu based search capabilities for recorded events as well as access to live or recorded data via the Ethernet optional 1 2 Features Single channel Composite Video Input Output connection Accepts Single Camera input or a Multiplexed input from most popular multiplexers Compatible with Color or Monochrome cameras Records up to 60 pictures per second NTSC or 50 pictures per second PAL Continuous Recording in Disk Overwrite mode Video Archiving via the unit s SCSI port Access to Live or Recorded video via the Ethernet Ethernet option only Continues Recording
43. o set the Date format use the Jog to select the desired Date format Format the Date as either DD MM YY Select Format MM DD YY YY MM DD Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes a Main Menu gt Time Date Set Time 1 With HH MM Ss highlighted press the Enter button The highlighting will move to the row of numbers 03 05 53 2 Enter the time in Hours Minutes and Seconds Use the Jog to change the values Use the Shuttle to navigate among the eases e three fields Press the Enter button to confirm the selection To Save the changes and Exit the menu Use the Jog to select OK then press the Enter button OR 5 To Exit the menu without making changes Use the Jog to select CANCEL then press the Enter button Calibur DSR 1000eZ 1 8 0150 0238A a Main Menu gt Time Date Set Date 1 With MM DD YY DAY highlighted press the Enter button The highlighting will move to the row of numbers MM DD YY DA 12 17 00 SUN 2 Enter the date in Months Days Years Day of the Week will update automatically Use the Jog to change the values Use CANCEL OK the Shuttle to navigate among the three fields Press the Enter button to confirm the selection To Save the changes and Exit the menu Use the Jog to select OK then press the Enter button OR 5 To Exit the menu without making ch
44. og to select the desired Record Quality Select High Med or Low Higher record quality s use lower compression requiring more disk space Select Quality Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes 4 5 Main Menu Display Settings Use this menu to specify what status information will be displayed on the Current Time Date primary monitor Select On or Off for the following items Record Capacity e The current time and date ya a Last Alarm Playback Time Date e The remaining amount of time before the hard disk runs out of record space e The Archive Status e Thetime and date of the last alarm e During Playback the time and date the recording was made a Main Menu gt Display Settings gt Current Time Date To display the current Time and Date near the upper right hand corner of the primary monitor select ON Use the Jog to select On or Off Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes Calibur DSR 1000eZ 4 6 0150 0238A a Main Menu gt Display Settings gt Record Capacity Select ON to display the amount of time remaining before the hard disk runs out of record space The data is displayed near the upper left hand corner of the primary monitor The unit displays the Record Capacity with two measures of time and switc
45. ord speed must be changed in the menu system For information about altering the alarm record speed see Main Menu Record Settings Alarm Record Speed on page 4 5 of the Operator Programming section of this manual The unit returns to the normal record speed when the alarm condition ends 0150 0238A 2 1 Calibur DSR 1000eZ Disk Nearly Full Notification This message will appear on the primary monitor to Disk Full Recording Has Stopped indicate that the unit has stopped recording because the disk is full In No Overwrite mode The user must acknowledge OK the on screen message by pressing the Enter button Unit will not record over previously recorded data To continue recording the data must be erased or deleted in the Advanced gt Disk Maintenance menu In Overwrite Once mode The user must acknowledge the on screen message by pressing the Enter button The unit will continue recording again when the user presses the Record button 2 2 Playback Play Forward To begin normal playback press the Play Forward button The unit will begin PLAY playing back data from the beginning of the last recording session O Playback is indicated e Ae PLAY near the upper left hand corner of the primary monitor for three seconds Play Forward button Reverse Play To begin reverse playback press the Reverse play button The unit will begin REVERSE PLAY playing back data from the beginning of the last recording sessio
46. p time e The record speed e The record quality e Whether the event is enabled EDIT Mode Hit ENTER To Toggle EDIT Mode 0150 0238A 4 3 Calibur DSR 1000eZ Creating a Timed Recording 1 Using the Jog Shuttle to navigate highlight the DATE parameter of the last line item indicated with double dash marks 2 Press the Enter button to enter the Edit mode EDIT MODE will appear on screen in the lower left hand corner of the Timer Settings menu The user may press the Enter button to exit Edit mode at any time 3 Use the Jog to change the values of the DATE setting Date Day of the Month 1 through 31 Day of the Week Monday through Sunday Range of Days All Weekdays Monday Friday All Weekend Days Saturday Sunday Monday Sunday Everyday When finished entering the Date use the Shuttle to navigate the START setting 5 Use the Jog Shuttle to enter the time the recording will begin The Hours and Minutes are edited separately The start and stop times are always configured in a 24 hour clock When finished entering the start time use the Shuttle to navigate to the STOP setting 6 Use the Jog Shuttle to enter the time the recording will end Entering a time before the start time will cause the unit to record until the indicated stop time on the next day When finished entering the stop time use the Shuttle to navigate to the SPD setting 7 Use the Jog to enter the record speed in pictures per second
47. proved grounded wrists straps etc to avoid damage to this unit or its internal components from electric discharge WARNING This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions in this manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to subpart J of part 15 of FCC rules which are designed to provide reasonable protection against such interference when operated in a commercial environment This equipment has also been tested and found to comply with the requirements for a CE Class A device and TUV safety standards Operation of this equipment in a residential area may cause interference in which case the user is required to take all measures that are necessary at the user s expense to correct the interference Calibur DSR 1000eZ i 0150 0238A IMPORTANT INFORMATION Software and or firmware is furnished to the purchaser under a license for use on a single system Software and or firmware included with this equipment are the sole proprietary property of confidential to and copyrighted by GE Interlogix Corvallis Oregon USA The software firmware are not to be copied or disclosed in any manner without the express written consent of GE Interlogix All information and specifications furnished by GE Interlogix are believed to be accurate and reliable No r
48. r Connect the Accessories PCB supplied with the unit to 1 5 the Accessories Port Wire all accessories to the Accessories PCB 00000 Do not attempt to wire accessories directly to the DB 9 connector 6 0000 9 If the Accessories PCB is lost or missing contact GE Interlogix Customer Service for a replacement Part Number 0900 0127a As a substitute purchase a female DB 9 connector and make all connections as shown in DB 9 Connector on Back Panel this section Pin 1 Alarm In Pin 6 Error Out Pin 2 Alarm Out Pin 7 Ground Pin 3 Record Start In Pin 8 Videoloss Out Pin 4 Alarm Record Reset Pin 9 Disk End Out Pin 5 VEXT Pulse Out Pin 10 Ground Accessories PCB 0150 0238A 1 5 Calibur DSR 1000eZ Alarm In An alarm condition can be activated by an Active Low TTL input Input Active Low TTL w pull ups or by relay contact devices such as pressure pads passive or Normally Open Relay infrareds door switches or other similar devices High 5V 12V tolerant Low Ground Minimum Duration 0 5 Seconds Figure 1 4 Normally Open Relay Alarm Connection Alarm Input Normally Open Closes During Alarm Ground lt Pin 7 or 10 Accessories PCB Typical Alarm Device Refer to each alarm devices s manual for specific wiring details Alarm Out The Alarm output is activated when a teletext alarm is detected Output Active Low or while the Alarm Input is active The Alarm output is only High 12
49. r Recorded Alarms 1 Using the Shuttle to navigate highlight the ALARM parameter then press the Enter button The unit will enter Edit mode Use the Jog to activate the alarms search by placing an X in the check box Press the Enter button at any time to exit Edit mode Starting the Search Using the Shuttle to navigate highlight the START SEARCH parameter then press the Enter button The Search Results menu will appear Selecting from the Search Results 000 001 002 003 004 005 006 007 Start Date 01 21 2002 01 21 2002 01 21 2002 01 21 2002 01 22 2002 01 23 2002 01 24 2002 01 25 2002 008 01 26 2002 9 matches found ENTER to play event Use the Shuttle to select a recorded event Search Results Start Time 20 07 20 3 09 ALOE 07 2072 ZOT 07 ZOO 10 10 10 10 10 10 10 10 10 Days HH MM SS 0 04 35 15 0 01 00 3078 00 08 500 Se 00 46 55 38 22 07 56 06 31 43 Press the Enter button to select the event or press the Menu button to exit the Search Results menu 0150 0238A 2 5 Calibur DSR 1000eZ 3 THE MENU SYSTEM This section provides a brief overview of the menu system for complete information about Operator and Installer programming see section 4 Operator Programming or section 5 Installer Programming How to use this Manual Throughout this manual there are headings like these a Main Menu gt Timer Settings
50. rnet network connection settings Ethernet units only Modem Settings e The Modem connection settings a Advanced Menu Communications Baud Rate Use the Jog to select the Baud Rate Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes a Advanced Menu gt Communications gt Ethernet Settings An Ethernet session is an active network connection between a PC and the unit with the user viewing live camera images or accessing data stored on the hard disk Only available on ethernet models this warning box will appear Warning Machine will reset if any values change Select OK to continue OK Calibur DSR 1000eZ 5 4 0150 0238A Use this menu to adjust the Ethernet settings for your network Ethernet ENABLE Use the Shuttle to navigate to the desired settin 9 9 IP Address g 192 168 1 201 then use the Jog to adjust the value Subnet Mask e 2559255255920 Consult with your local MIS personnel before making Ethernet setting changes Gateway 0 0 0 0 CANCEL OK Select OK to confirm the selection and exit the menu OR Select CANCEL to exit the menu without making changes How the unit handles an Ethernet session At the start of an Ethernet session the unit locks out its own front panel and disables all RS 232 and RS 485 communications During the Ethernet session the unit can only be accessed remot
51. s the Enter button to confirm the selection and exit the Edit mode ao RON Use the Jog Shuttle to navigate to OK then press the Enter button to remove the selection and exit the menu 4 4 Main Menu gt Record Settings Use this menu to specify Ene Dass aaa Alarm Record Speed e The record speed during Normal recording Video Quality e The record speed when the unit detects an alarm condition e The recorded picture quality a Main Menu gt Record Settings gt Normal Record Speed Use the Jog to select the desired Normal Record Speed Normal Record Speeds Pictures Per Second NTSC 60 30 20 10 5 3 2 1 0 5 0 2 0 1 0 0 5 PAL 50 25 17 10 5 3 2 1 0 5 0 2 0 1 0 0 When the Normal Record Speed is set to 0 0 the unit will only record while an alarm is active Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes a Main Menu gt Record Settings gt Alarm Record Speed Use the Jog to select the desired Alarm Record Speed Alarm Record Speeds NTSC 60 30 20 10 5 3 2 1 0 5 02 0 1 PAL 50 25 17 10 5 3 2 1 0 5 0 2 0 1 Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making changes Pictures Per Second 0150 0238A 4 5 Calibur DSR 1000eZ a Main Menu gt Record Settings gt Video Quality Use the J
52. t the START SEARCH parameter then press the Enter button The Restore Search Results menu will appear Please note that restoring data indicated in this menu is not currently supported on the DSR 1000eZ unit Press the Menu button to exit the menu Restore Search Results Start Date 11 29 2000 11 29 2000 ENTER to play Available on Target Medium Start Time Size MB 10 00 04 279 x 10 03 25 67 x Selected 383 MB 652 MB SEARCH to restore a Main Menu gt Archive Setup gt Background Archive With the Background Archiving Feature turned ON the unit archives recorded data automatically Data is recorded to both the hard disk and the archiving device simultaneously The unit cannot Background Archive when the unit is recording at its highest record speed Use the Jog to select ON of OFF Press the Enter button to confirm the selection and exit the menu OR Press the Menu button to exit the menu without making any changes a Main Menu gt Archive Setup gt Archive Overwrite Mode For future use only Calibur DSR 1000eZ 4 12 0150 0238A a Main Menu gt Archive Setup gt Erase Archive Medium To erase the archived data press the Enter button The Erasing Media progress bar will appear Press the Enter button to cancel n CANCEL archiving at any time This feature is not available when archiving to a CD R device When the unit is finished erasing the data
53. the date of purchase The warranty specifically covers any defects in material and workmanship and does not cover equipment that has been abused damaged or modified For all warranty repairs GE Interlogix will cover all costs including parts labor and shipping Repaired equipment will be returned via the same method of shipment in which it was received If a customer requests a faster return shipment the difference will be charged For all non warranty repairs the customer will be billed for parts labor and shipping Labor will be billed in half hour increments Note Customers requesting an estimate prior to repair will be notified by phone If they cannot be reached they will be notified by fax If we are unable to reach the contact person for repair authorization after one phone attempt and two fax attempts the equipment will be returned without being repaired We will hold equipment no longer than two weeks Advance Replacement Policy When an advance replacement is required we will send the customer replacement equipment from our stock and receive the returned product in exchange The received equipment will be evaluated and the repair department will determine whether it is a warranty replacement If it is non warranty see our repair policy above for details The following guidelines will be used for all advance replacements e Fewer than 45 days from purchase GE Interlogix will replace the product with new equipment e Fro
54. the last character will Please RA Ent r The Password complete the password selection E OR If the password in the Confirmation Box matches the password from the Password box this message will appear The New Password Has Been Accepted Press the Enter button to select OK and exit the 153 menu If the password in the Confirmation Box does not match the password from the Password box this message will appear The Password Was Not Changed Press the Enter button to select OK and exit the LOK menu Calibur DSR 1000eZ 5 8 0150 0238A 5 11 Advanced Menu gt Firmware Upgrade Use this feature to upgrade the embedded machine code that controls the operation of the DSR 1000eZ Once selected from the Advanced menu the following warning box will appear Firmware Upgrade WARNING Do not power off unit until the operation is done Do You want to continue OK CANCEL Selecting OK will put the DSR 1000eZ into Firmware Upgrade mode The unit may now be programmed using WinFlash The Operation may be cancelled by powering off the unit as long as WinFlash has not started Once WinFlash has started any interruption can permanently damage the DSR 1000eZ After a successful upgrade the DSR 1000eZ will automatically reboot with the new firmware Note The unit must be in STOP mode before going into UPGRADE mode A Caution Do not remove power from the DSR 1000eZ after WinFlash has started A successful upgrade
55. tput signal of the Mux is wired directly to the alarm input of the VCR using the VEXT connection Calibur DSR 1000eZ 4 2 0150 0238A This teletext alarm detecting feature of the DSR 1000eZ is compatible with the following styles of Multiplexers e Kalatel e Philips e Robot e Pelco e Sanyo e Philips REO e ATV e ATV QSP e Vista VLM e QSI 1700 e Diebold Connecting to Dedicated Micros DM When connecting to a Dedicated Micros multiplexer e ltis necessary to connect the alarm output of the Mux to the alarm input of the DSR 1000eZ as you would do when connecting the alarm input on standard time lapse VCR e ltis necessary to configure the Main Menu gt Alarms gt Hardwire Alarm as Enabled e ltis necessary to configure the Main Menu gt Alarms gt Teletext Alarm as Disable 1 Use the Shuttle to navigate among the fields Hardwire Alarm Enable 2 Use the Jog to change the values of the highlighted Teletext Alarm Disable fields Alarm Buzzer Enable 3 To Save the changes and Exit the menu Use the CANCEL OK Jog to select OK then press the Enter button OR 4 To Exit the menu without making changes Use the Jog to select CANCEL then press the Enter button 4 3 Main Menu gt Timer Settings This menu allows the user to START STOP SPD pps QUALITY ON OFF program a timed recorded event Use this menu to specify e The date or days on which the recording will occur e The start and sto
56. use is indicated e As PAUSE near the upper left hand corner of the primary monitor for three seconds Single Frame Advance amp Single Frame Rewind During Pause mode rotate the Jog dial to view the frame directly before or after the frame displayed on screen Start of Data End of Data ES Jog Shuttle ZAN Jog Shuttle PAUSE O Pause button VNS Jog Shuttle If the start or end of data is reached during playback START OF DATA Or END OF DATA s indicated near the upper left hand corner of the primary monitor 2 3 The Search Interface The Search Interface feature allows the user to search the hard disk for recorded events such as an alarm condition or a previous recording session For example each time Record mode is activated it is considered a separate recording session To enter the Search Filters menu press the Search button The Search Filters menu is displayed on the primary monitor 0150 0238A 2 3 SEARCH 72 e Search button Calibur DSR 1000eZ e The Start and Stop date of Start Stop the search DATE 12 25 00 01 01 01 e The Start and Stop time of MM DD YY MM DD YY the search SIUE Stop e Which cameras to search TIME 11 11 21 12 34 34 exclusively e To search for recorded 4 we sy AN 5 CATAS alarms CAMERA 1E 1E 1E JI JI 1I 1 CANCEL START SEARCH Searching for All Recorded Events Using the Shuttle to navigate highlight START SEARCH th
57. xer Format Adjust Picture Front Panel Lock Factory Settings Change Password Firmware Upgrade 0150 0238A a Advanced Menu Disk Overwrite Mode Use this menu to specify how the unit will handle disk overwrite Select Mode issues once the hard disk becomes full Select either e No Overwrite Overwrite Once Continuous Overwrite e Continuous Overwrite a Advanced Menu Disk Maintenance The user can have previously recorded information Delete Undelete Erase e Deleted with the possibility of restoring it e Undeleted restored if it has not yet been overwritten e Erased removed with no possibility of restoring it Selecting erase will display the following warning box All data will be permanently erased Do You want to continue CANCEL OK a Advanced Menu gt Audio Record Setting Audio equipped model only OFF G 711 64kb s Use this menu to e Select Off and Disable the audio recording capability e Select G 711 and Enable the audio recording capability This selection will be grayed out if the DSR 1000eZ is not equipped with the audio option a Advanced Menu Auto Delete Mode Use this menu to program the Auto Delete Mode The options available are from 7 to 99 days and Off 30 days is the default setting 0150 0238A 3 5 Calibur DSR 1000eZ ADM Setting ADM will change Are you sure Yes a Advanced Menu Communications Use thus menu to sp

0150-0238A DSR-1000eZ User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents