Home

operation

1. RANCH R ITE HAY TEDDER HT 10 User Manual This Operator s Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times READ UNDERSTAND and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment C01 Cover ENGLISH TO THE OWNER OPERATOR DEALER All implements with moving parts are potentially hazardous There is no substitute for a cautious safe minded operator who recognizes the potential hazards and follows reasonable safety practices The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents BEFORE YOU START Read the safety messages on the implement and shown in your manual Observe the rules of safety and common sense A WARNING TO AVOID SERIOUS INJURY OR DEATH 1 READ AND UNDERSTAND OPERATOR S MANUAL 6 KEEP BYSTANDERS CLEAR OF MOVING PARTS 2 TRACTOR MUST BE EQUIPPED WITH ROLL OVER AND WORKING AREA KEEP CHILDREN AWAY PROTECTION ROPS AND SWAY CHAINS T OO NOT LIFE LOWER OR OPERATE UNLESS 3 ALWAYS WEAR SAFETY GLASSES SAFETY SHOES EVERYONE 15 CLEAR OF IMPLEMENT AND SEAT BELT FASTENED THOHTLY 8 USE INCREASED CAUTION ON SLOPES amp NEAR 4 STOP TRACTOR LOCK BRAKES AND BLOCK UP BANKS AND DITCHES TO PREVENT OVERTURN OR SUPPORT IMPLEMENT SECURELY BEFORE 9 LOCK LIFT LEVER UP FOR TRANSPORT HAVE SMV WORKING UNDER RAISE
2. sc 10 Never allow children to operate ride on or come close to the Tractor or Implement Usually 16 17 year old children who are mature and A DANGER responsible can operate the implement with adult supervision if they have read and understand the Operator s Manuals been trained in proper operation of the tractor and Implement and are physically large enough to reach and operate the controls easily sa 11 Do not mount or dismount the Tractor while the tractor is moving Mount A WARNING the Tractor only when the Tractor and all moving parts are completely stopped sc 12 Start tractor only when properly seated in the Tractor seat Starting a A DANGER tractor in gear can result in injury or death Read the Tractor operators manual for proper starting instructions sa 13 Start orly from seat in park of neta Stardng is gear kilis HT 10 Safety Section 1 6 2014 Ranch Rite SAFETY Do not operate this Equipment with hydraulic oil or fuel leaking Oil and fuel are explosive and their presence could present a hazard Do not check for leaks with your hand High pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene To check for a hose leak SHUT the unit ENGINE A WARNING OFF and remove all hydraulic pressure Wear oil impenetrable gloves safety glasses and use Cardboard to check for evidence of oil leaks If you suspect a leak REMOVE the HOSE and have it test
3. otherwise damaged or deformed OPS U 0039 HT 10 Operation Section 4 8 2014 Ranch Rite OPERATION Never work under the Implement the framework or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death sc 14 A DANGER 7 DRIVELINE ATTACHMENT The driveline yoke and tractor PTO shaft must be dirt free and greased for attachment To connect the tedder driveline to the tractor PTO output shaft pull the driveline yoke collar back and align the grooves and splines of the yoke with those of the PTO shaft Push the driveline yoke onto the PTO shaft release the locking collar and position the yoke until the locking collar balls are seated onto the PTO shaft Push and pull the driveline back and forth several times to ensure a secure attachment OPS HT 0003 7 1 Driveline Length Check When fitting the hay tedder to the tractor the driveline must be inspected to ensure that it is connected correctly both at the tractor end and at the implements end If a safety system is provided this should be fitted to the machine end not to the tractor end During both transport and use avoid conditions where the Driveline transmission shaft is extended to the maximum In all working conditions the telescopic tubes must overlap by at least 1 3 of their length Figure OP 224 HT 10 Operation Section 4 9 O 2014 Ranch
4. AVOID SERIOUS INJURY OR DEATH READ AND UNDERSTAND OPERATOR S MANUAL 6 KEEP BYSTANDERS CLEAR OF MOVING PARTS TRACTOR MUST BE EQUIPPED WITH ROLL OVER AND WORKINGAREA KEEP CHILDREN AWAY PROTECTION ROPS ANC SWAY CHAINS 7 DO NOT LIFT LOWER OR OPERATE UNLESS ALWAYS WEAR SAFETY GLASSES SAFETY SHOES EVERYONE I5 CLEAR OF IMPLEMENT AND SEAT BELT FASTENED TIGHTLY USE INCREASED CAUTION ON SLOPES A NEAR STOP TRACTOR LOCK BRAKES AND BLOCK UP OR BANKS AND OITCOHES TO PREVENT OVERTURN SUPPORT IMPLEMENT SECURELY BEFORE amp LOCK LIFT LEVER UP FOR TRANSPORT HAVE WORKING UNDER RAISED COMPONENTS SMV SIGN VISIBLE FOLLOW LOCAL LAWS 5 ALLOW NO RIDERS AT ANY TIME ON TRACTOR OR 10 USE PARKING STAND OR BLOCK UP WHEN IMPLEMENT FALLING OFF CAN KILL UNHITCHING FROM TRACTOR so P N 999200 HT 10 Safety Section 1 16 2014 Ranch Rite SAFETY Operator s Manual with repair parts and warranty NOTICE TO OWNER implement during final was attached to this inspection qi ua uy A val rad im a a dd ny E il 5 ES te a A i Be ce E E ik Ll q Hm m 5 pra kar a pe oe Lala thn mmr E PR 2 E e a r un tla T o ey Dn m gt a me pr oo o Siro 1 Sis EE 5 wh m L Leo 2 mx EU g o7 amp a e pea LA Bomp 23 14 T Oa ao ae ae mi de T ta BN J tS a e oO az co E 23 ad Je TI e 20 qu g rg a DE ak fe ui z A D7 Ez Read and understand
5. Mnt HT 0001 1 2 Remove plugs 1 amp 2 Inject grease into hole A by using nipple 3 fitted to a pump until grease comes out of upper hole B A complete lubrication requires 2 lbs of grease After lubrication you should retighten plugs 1 amp 2 Aint FOOD ROTOR PHASING Whenever maintenance is required on the gearboxes the rotor phasing must be checked before operation to keep the arms from interfering in operation The correct rotor phasing is shown below Mnt HT 0002 t VWint BT G002 HT 10 Maintenance Section 5 2 2014 Ranch Rite To get Newton Meters multiply pound foot of torque by 1 356 MAINTENANCE STORAGE Lower the tongue stand and disconnect the tender from the tractor Do not disconnect the tedder from the tractor before blocking wheels and securing stand Before disconnecting the tedder from the drawbar crank the lifting screw to adjust the tines A CAUTION tothe working position This will move the center of gravity forward so more of the weight of the machine is on the tongue stand and prevent the tedder from tilting backwards PROPER TORQUE FOR FASTENERS The chart lists the correct tightening torque for fasteners When bolts are to be tightened or replaced refer to this chart to determine the grade of bolts and the proper torque except when specific torque values are assigned in manual text RECOMMENDED TORQUE IN FOOT POUNDS UNLESS OTHERWISE STATED IN THE MANUAL NOTE
6. Never allow children to operate ride on or come close to the Tractor or Implement Usually 16 17 year old children who are mature and responsible can operate the implement with adult supervision if they have read and understand the Operator s Manuals been trained in proper operation of the tractor and Implement and are physically large enough to reach and operate the controls easily sc 11 A DANGER DANGER Never allow children or other persons to ride on the Tractor or Implement A Falling off can result in serious injury or death se 10 4 2 Dismounting the Tractor Before dismounting park the tractor and implement on a reasonably level surface apply the parking brake idle the engine down disengage the PTO and lower the implement to the ground Shut down the tractor engine according to the operator s manual remove the key and wait for all motion to completely stop Never leave the seat until the tractor its engine and all moving parts have come to a complete stop Use hand rails and steps when exiting the tractor Be careful of your step and use extra caution when mud ice snow or other matter has accumulated on the steps or hand rails Use all handrails and steps for support and never rush or jump off the tractor OPS U 0009 ENGINE end the tractor transmission in parking gear disengage the PTO stop the EJ A DANGER engine remove the key and wait for all moving parts to stop Place the uJ E ema t tractor
7. important safety features on the implement in good condition to ensure the information is available to the operator at all times Ensure the manual canister is secured to the ees equipment with the operator s manual inside HE e Ensure all safety signs are in place and legible Replace missing damaged and _ illegible 7 decals OPS U 0011 5 HT 10 Operation Section 4 12 2014 Ranch Rite OPERATION Hay Tedder PRE OPERATION Inspection Mower ID Make RANCH R I TE Date Shift Before conducting the inspection make sure the tractor engine is off all A WARNING rotation has stopped and the tractor is in park with the parking brake engaged Make sure the Tedder is resting on the ground or securely blocked up and all hydraulic pressure has been relieved Condition at Specific Comments if Start of Shift not O K Item The Operator s Manual is in the Canister on the Hay Tedder All Safety Decals are in place and legible The Tongue Hitch connection bolts amp pins are tight There are no cracks in Tongue or Hitch There are no cracks in Loader Arms or Mounts The Tow Chain is secured to the Tractor amp Hay Tedder Driveline Gearbox Shields are in good condition Driveline Clutches are in good condition not frozen Driveline Telescoping Members amp U Joints are lubricated Driveline Yokes are securely attached to PTO amp Tiller Gearbox Mounting Bolts are tight Gearbox Oil is at the proper level The Wing c
8. the Operators Manual before operating the implement 2 Complete sign and mad the Warranty Regisiratior i Card today P N 00763977 For safety and to guarantee optimum product Ranch Rite use genuine always reliability IMPORTANT For your aztaby and do quarantee optimam produced rallahiity always une replacement parts 2 2 t kA E E 3 E E E E E E E pa a e E Th E T mu a p E a i T ses ey FE E a F tee Erpe sig L EX e ero 80 Bad Zes ane Ez T FEO E i ag a Fg 58 2s e g SE FE t iE ES E eS Eg SB HE EE P N 00786980 Red Reflectors P N 2738332 Yellow Reflectors P N 2738333 Safety Section 1 17 HT 10 2014 Ranch Rite SAFETY Logo Product Name Ranch Rite 8 RANCH RITE re Hild HT 10 Name Slow Moving Vehicle Decal Keep SMV reflector clean and visible DO NOT transport or operate without the SMV P N 03200347 Read Operator s Manual The operator s manual is located inside this canister If the manual is missing order one from your dealer P N 00776031 HT 10 Safety Section 1 18 2014 Ranch Rite SAFETY Federal Laws and Regulations This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators This section is not intended as a legal interpretation of
9. the law and should not be considered as such Employer Employee Operator Regulations U S Public Law 91 596 The Williams Steiger Occupational and Health Act of 1970 OSHA This Act Seeks lo assure so far as possible every working man and woman in the nation safe and healthful working conditions and to preserve our human resources DUTIES Sec 5 a Each employer 1 shall furnish to each of his employees employment and a place of employment which are free from recognized hazards that are causing or are likely to cause death or serious physical harm to his employees 2 shall comply with occupational safety and health standards promulgated under this Act b Each employee shall comply with occupational safety and health standards and all rules regulations and orders issued pursuant to this Act which are applicable to his own actions and conduct OSHA Training Requirements Title 29 Code of Federal Regulations Part 1928 57 a 6 www osha gov Operator instructions At the time of initial assignment and at least annually thereafter the employer shall instruct every employee who operates an agricultural tractor and implements in the safe operating practices and servicing of equipment with which they are or will be involved and of any other practices dictated by the work environment Keep all guards in place when the machine is in operation Permit no riders on equipment Stop engine disconnect the power source a
10. the unit has been subjected to misapplication abuse misuse negligence fire or other accident 3 If parts not made or supplied by Ranch Rite have been used in connection with the unit if in the sole judgement of Ranch Rite such use affects its performance stability or reliability 4 If the unit has been altered or repaired outside of an authorized Ranch Rite dealership in a manner which in the sole judgement of Ranch Rite affects its performance stability or reliability 5 To normal maintenance service and normal replacement items such as gearbox lubricant hydraulic fluid worn blades or to normal deterioration of such things as belts and exterior finish due to use or exposure 6 To expendable or wear items such as teeth chains sprockets belts springs and any other items that in the company s sole judgement is a wear item NO EMPLOYEE OR REPRESENTATIVE OF RANCH RITEIS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY RANCH RITE S SERVICE MANAGER 1830 W 15TH STREET HOUSTON TEXAS 77008 VDDD DDD DDD DDD DDD DDD DDDDTX Record the model number serial number and date purchased This information will be helpful to your MODEL NUMBER dealer if parts or service are required SERIAL NUMBER MAKE CERTAIN THE WARRANTY Eien Shen eee a HAS BEEN FILED WITH RANCH RITE HOUSTON TEXAS RANCH RITE TO THE OWNER OPERATOR DEALER To keep your implem
11. 10 One bundle contains right hand tines and the other contains left hand tines 1 Install the tines according to the diagram below using bolt 3 and nut 5 paying particular attention to the direction of rotation or the rotors and the orientation of the drawbar DHREC TON OF ROTATION DIRECTION GF ROTATION FORWARD CHRECTION rr RH ROTOR CN VS 1H ROTAR L H TIENE RH TINE Asm HF OGA SAFETY GUARDS INSTALLATION 1 Install right hand and left hand safety guards as shown in Figure 5 using two bolts 15 and two serrated washers 14 2 Insert plugs 13 into ends of safety guards Aarm 0GS HT 10 Assembly Section 3 4 2014 Ranch Rite OPERATION SECTION OPERATION Bush Hog HT 10 HAY TEDDER OPERATION INSTRUCTIONS Your Ranc Rite Hay Tedder should now be assembled and inspected for any evidence of defective or damaged parts before use Any evidence of damage should be reported to your dealer immediately This section of the Operator s Manual is designed to familiarize instruct and educate safe and proper implement use to the operator Pictures contained in this section are intended to be used as a visual aid to assist in explaining the operation of a Hay Tedder and are not necessarily of a HT 10 Some pictures may show shields removed for purposes of clarity NEVER OPERATE this implement without all shields in place and in good operational condition The operator must be familiar with the
12. D COMPONENTS SIGN VISIBLE FOLLOW LOCAL LAWS 5 ALLOW NO RIDERS AT ANY TIME ON TRACTOR OR 10 USE PARKING STAND OR BLOCK UP WHEN IMPLEMENT FALLING GFF CAN KILE UNHITCHING FROM TRACTOR serico WARRANTY INFORMATION Read and understand the complete Warranty Statement found in this Manual Fill out the Warranty Registration Form in full and return it to within 30 Days Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain TABLE OF CONTENTS SAFETY SECHON aia 1 1 General Safety Instructions and PractiCes ooonccncccccooonnccnnonononnnenononnnnnnnnnnnnononnnnnnnnonnnnnnnnnnnnnnnnnnnnnannnnnononanenons 1 2 Operator oaley Instructlens and PraGuCeS a A ee See 1 3 Equipment Operation Safety Instructions ANd PractiCesS oooccccccocnnnncconncnnnnnnnnnnonnnnnnonnnnnnnnnnannnnnnnnnnnnononanannnnnos 1 5 Connecting or Disconnecting Implement Safety Instructions amp PractiCes ooccccccccccnnnccnnccccnnnncnnnnnnnnnccnnnnncnnnnnns 1 8 Transporting Safety Instructions and Practices ooccccccccconncnnccononncnnnnonnnnnnnnnnononnnnnnnnnnnnnnnnnnnnnonnnnnnnnnnnnnnnnnennnnnns 1 9 Maintenance and Service Safety Instructions and Practices occccccccconnconncconoonnnnncnnnonnnonnnnnnnnnncnnnnnnonanennnnnnns 1 11 Biciors elots e atacado met Cae eee thre mre laico frreticd 1 14 CG AS SOON etic cra 1 15 Decal DESCANSO daa contents cota devas 1 16 Federal baws and
13. FLECT LOGO NAME SER PLT REFLECT Safety Section 1 15 DESCRIPTION Spanish Get Translation Rotors Maintain Weight for Steerage Multiple Hazard Notice To Owner Genuine Bush Hog Parts Red Reflector Yellow Reflector Ranch Rite HT 10 Serial Plate SMV Canister Operators Manual Operator s Manual Bolt Flatwasher Locknut SAFETY Decal Description Peligro Translation If you do not know how to read English please find someone who knows how to read English Si No Lee Ingles Pida Ayuda a Alguien Que Si Lo Lea Para Que le Traduzca las Medidas de Seguridad 007235746 P N 00725746 DANGER Keep clear of rotors serious injury or death may result from entanglement KEEP CLEAR OF ROTORS SERIOUS INJURY OR DEATH MAY RESULT FROM ENTANGLEMENT DISENGAGE PTO amp SHUT OFF TRACTOR FF BYSTANDERS ENTER AREA OR BEFORE SERVICING WPA P N 3678303 WARNING Tractor rearing Tractors roaring Up may cause machine damage Injury or death Never Use tractor without ROPS Koop seatbolt fastened snugly to prevon falling off and injury NO RIDERS 7 Add tractor front weight as needed ta Mevor start or accolorate suddenly te maintain maintain safe steering traction safe steering traction Slow down In curved and rough places Do not lit heavy implement while going up Stay away from soft banks and holes steep slopes P N 999001 WARNING Multiple Hazard and General Safety TO
14. ING Your driving vision may be reduced or impaired by the tractor cab or implement Before driving on public roadways identify any limited vision areas and make adjustments to your operating position mirrors and the implement transport position so that you can clearly see the area where you will be traveling and any traffic that may approach you Failure to maintain adequate vision of the public roadway and traffic can result in serious injury or even death sri 10 A WARNING Maintenance and Service Safety Instructions and Practices RACY Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement Place the Implement on the ground or securely jy A WARNING blocked up disengage the PTO and turn off the tractor engine Push ya and pull the Remote Cylinder lever in and out several times prior to starting any maintenance or repair work S3PT 09 Make sure the PTO shield integral driveline shields and input shields A DANGER are installed when using PTO driven equipment Always replace any shield if it is damaged or missing S3PT 8 Always disconnect the main PTO Driveline from the Tractor before performing service on the Implement Never work on the Implement with the tractor PTO driveline connected and running Rotating Parts Blades or Drivelines could turn without warning and cause immediate entanglement injury or death S3PT 11 A DANGER A WARNING Keep fingers clear of adjusting hole
15. Regulations iaa A eee 1 19 INTRODUCTION SEC TION m osses ritena iii dida 2 1 ASSEMBLY SEC HON conan pias 3 1 GENERAEASSEMBE Y eee oe un OP ee ee ene ee eee 3 2 AXLE INSTALLATION a oo 3 2 TIRES WHEEL ASSEMBLIESANSTALLATONE il a Cde 3 3 DRAWBAR amp SHIELDS INSTALLATION ca acond 3 3 TINE ASSEMBLIES INSTALLATION a O acces 3 4 SAFETY GUARDS INSTALE THON a a e R 3 4 OPERATION SECTION conca iia 4 1 Standard Equipment and Specifications sra titi 4 2 OPERATOR REQUIREMENTS 00 aaa ia 4 3 TRACTOR REQUIREMENTS unir teed oi a a oo 4 4 MOPS and Seat o os Geek tee tls 4 4 Itata POP eo eE ES ECO aan O Ueda teat esol machete 4 4 Dirawbat 2 PUllTYy pe MOWE it it 4 5 Front Ena Weh ona tii la vida uve banat ii Aticos 4 5 GETTING ON AND OFF THE TRAG TOR lt a dr a ded 4 5 ECM NM Ned AS terete eee te eo o dn chon aie 4 5 Dismounting the Traci Rita aio ariba 4 6 STARTINE THE TRACTOR sa a A e os 4 7 CONNEC TING TH HAY TEDDER TO THE TRACTOR dada a 4 7 Connecting the Hay WSO e Raencsacdca diia lia 4 8 Sas OW CMAN wee a os 4 8 DRIWMELINEATTA COMENT a e el o 4 9 Driveline Len CA ls e tenet 4 9 PRESOPERATON INSPECTION AND SERVICE caian ii dis 4 11 Tractor Pre Operation inspeccion Sence eiii 4 11 Hay Tedder Pre Operation InspectiON ServiCe ccccccccccceeseeccceuceecceuseccceeeueeecseuseceesaueceessauseesssuseeesessanseeeesas 4 12 DRIVING THE TRACTOR ANDIMPLEMENT 0 a ati athe Aa 4 15 AMAT ld 4 16 Brake and Differential Lock Sel lancia 4 16 Drivingith
16. Rite OPERATION Conversely when the driveline shaft is contracted to the maximum there should still be a gap of approximately 2 50 mm Figure OP 225 lake particular care when connecting the two Driveline shaft end forks and make sure that they are fully secured This is achieved by inserting the safety pins and bolts 1 in the special slots 2 on the power takeoff shafts on both the tractor and implement ends Figure OP 226 HT 10 Operation Section 4 10 2014 Ranch Rite OPERATION 8 PRE OPERATION INSPECTION AND SERVICE Before each use a pre operation inspection and service of the implement and tractor must be performed This includes routine maintenance and scheduled lubrication inspecting that all safety devices are equipped and functional and performing needed repairs DO NOT operate the unit if the pre operation inspection reveals any condition affecting safe operation Perform repairs and replacement of damaged and missing parts as soon as noticed By performing a thorough pre operation inspection and service valuable down time and repair cost can be avoided OPS U 0029 Periodically inspect all moving parts for wear and replace when necessary with authorized service parts Look for loose fasteners worn A WARNING broken parts and leaky or loose fittings Make sure all pins have cotter pins and washers Serious injury may occur from not maintaining this machine in good working order sc 21 8 1 Tracto
17. These values apply to fasteners as received from supplier dry or when lubricated with normal engine oil They do not apply if special graphited or molydisulphide greases or other extreme pressure lubricants are used This applies to both UNF fine and UNC coarse threads Proper Torque Values for Standard Bolts Proper Torque Values for Metric Bolts Head Marking Head Marking Head Marking Head Marking Head Marking Head Marking Diameter Three Lines Six Lines i 4 6 8 8 or 9 8 10 9 12 9 Grade Five Grade Eight Pound Foot Value Pound Foot Value Pound Foot Value Pound Foot Value Dry Dry Dry Dry 6mm 3 Y 7 9 o 0 E ee AA A E 196 384 529 27mm 262 968 27mm 262 24 47 81 202 279 394 537 680 998 137196 20 279 O 267 8A 8H 3645 461608 PONEIS O E 1312 1353 HT 10 Maintenance Section 5 3 O 2014 Ranch Rite LIMITED WARRANTY DAA DEA a a a a a a a as DS DS DS XA MEA VEAVEA a a as a a a a as as as DS VEA DS Dl Ranch Rite warrants to the original purchaser of any new Ranch Rite equipment purchased from an authorized dealer that the equipment be free from defects in material and workmanship for a period of one 1 year for non commercial state and municipalities use and ninety 90 days for commercial use from date of retail sale The obligation of Ranch Rite to the purchaser under this warranty is limited to the repair or replacement of defective parts Replacement or repair parts ins
18. aft penetrates the outer housing until the assembly becomes solid it can shorten no more Bottoming out can cause serious damage to the Tractor PTO by pushing the PTO into the Tractor and through the support bearings or downward onto the PTO shaft breaking it off A broken driveline can cause personal injury S3PT 18 Never unhitch without using the Tongue Jack The Tongue is very heavy Attempting to lift the Tongue without using the Tongue Jack could cause strains or other injury Allowing the tongue to fall suddenly and unexpectedly could result in crushing injury Use the Tongue Jack for lifting the Implement only Overloading the Tongue Jack can cause failure with possible serious bodily injury or even death sri 04 On a fully assembled unit do not remove the Wing Retaining Strap until hoses are attached to the tractor and the Wing Cylinders are filled with oil Lower the Wings slowly and carefully Keep bystanders away during operations sti 05 Transporting Safety Instructions and Practices Be particularly careful when transporting the Implement with the Tractor Turn curves or go up hills only at a low speed and using a gradual steering angle Rear mounted implements move the center of gravity to the rear and remove weight from the front wheels Make certain by adding front ballast that at least 20 of the tractor s weight is on the front wheels to prevent rearing up loss of steering control or Tractor tip over Slow down on rough
19. and all bolts and nuts are properly torqued Failure to properly service repair and maintain this Implement in good operating condition could cause component failure and possible serious injury or even death sa 35 Use caution and wear protective gloves when handling sharp objects such as blades knives and other cutting edges Be alert to worn component surfaces which have sharp edges Sharp surfaces can inflict severe laceration injuries if proper hand protection is not worn SG 37 Safety Section 1 12 2014 Ranch Rite SAFETY PARTS INFORMATION Ranch Rite products are designed utilizing specifically matched system components to ensure optimum equipment performance These parts are made and tested to Bush Hog specifications Non genuine will fit parts do not consistently meet these specifications The use of will fit parts may reduce equipment performance void warranties and present a safety hazard Use genuine Bush Hog parts for economy and safety SPBH 2 SEE YOUR RANCH RITE DEALER A rear Implement can fall if not properly supported Always use the stand on the front hitch A DANGER if equipped or block up securely to prevent falling and possible crushing injury and or other injury from holding or lifting heavy components Use the stand to stabilize the implement during storage S3PT 3 To prevent tipping of Implement when stored in folded position use carrying wheels or A CAUTION adequate stands on center fram
20. assersby The implement must be completely lowered and the deck positioned at a safe operating height NEVER engage the PTO with the implement in the raised position Set the tractor engine speed at approximately 1 000 RPM before engaging the PTO Shift the PTO control to the on position and slowly increase the engine speed until the PTO is operating at 350 450 RPM 540 MAX If you hear unusual noises or see or feel abnormal vibrations disengage the PTO immediately Inspect the implement to determine the cause of the noise or vibration and repair the abnormality OPS HT 0017 HT 10 Operation Section 4 19 2014 Ranch Rite OPERATION 11 3 Shutting Down the Implement To shut down the implement first bring the tractor to a complete stop Then slow down the implement by reducing the engine speed before disengaging the PTO Wait for all motion to stop before proceeding to drive or shut down the tractor Park the tractor on a level surface place the transmission in park or neutral and apply the parking brake lower the attached implement to the ground shut down the engine remove the key and wait for all motion to come to a complete stop before exiting the tractor OPS HT 0016_A p er 12 DISCONNECTING THE HAY TEDDER FROM THE TRACTOR Before disconnecting the hay tedder the PTO must be disengaged and all movement must cease Move the hay tedder to a level storage location and lower the unit to the ground If the hay tedder is no
21. bystanders from injury or death Read and understand these Safety Messages before assembling operating or servicing this Implement This equipment should only be operated by those persons who have read the manual who are responsible and trained and who know how to do so responsibly The Safety Alert Symbol combined with a Signal Word as seen below is used throughout this manual and on decals which are attached to the equipment The Safety Alert Symbol means ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED The Symbol and Signal Word are intended to warn the owner operator of impending hazards and the degree of possible injury faced when operating this equipment Practice all usual and customary safe working precautions and above all remember safety is up to YOU Only YOU can prevent serious injury or death from unsafe practices Indicates an imminently hazardous situation that if not avoided WILL result in DEATH OR A DANGER VERY SERIOUS INJURY A WARNING Indicates an imminently hazardous situation that if not avoided COULD result in DEATH OR SERIOUS INJURY A CAUTION Indicates an imminently hazardous situation that if not avoided MAY result in MINOR INJURY Identifies special instructions or procedures that if not strictly observed could result in IMPORTANT damage to or destruction of the machine attachments or the environment NOTE dentifies points of particular interest for more efficient and convenient op
22. chines to the tractor is very simple as it is only necessary to couple the drawbar hitch to the tractor hitch using a pin of appropriate size strength and shape Always use extreme care when reversing the tractor towards the machine Once the implement is hitched to the tractor the drawbar parking stand 6 must be raised from the parking position To do this remove clip 8 and pin 7 and rotate the parking stand so that it is paralleled with drawbar 1 Fasten into the new position using pin 7 and clip 8 Once this procedure is completed insert the quick release coupling into the tractor socket 6 2 Safety Tow Chain If the mower is towed on a public roadway a safety chain with tensile strength equal to or greater than the gross weight of the mower must be connected between the tractor and mower This will help control the implement in the event the tongue becomes disconnected from the drawbar Make sure the chain is attached to a secure location on the tractor and not to an intermediate support After connecting both ends of the safety chain drive the tractor to the right and left to check for proper chain length Adjust length as necessary and allow only enough slack in the chain to make a maximum turn in both directions When not in use store the safety chain to protect it from mud or standing water by wrapping the chain around the tongue Replace the safety chain if one or more links or end fittings are broken stretched or
23. d When operating in traffic always use the Tractor s flashing warning lights and reduce your speed Be aware of traffic around you and watch out for the other guy sc 19 HT 10 Operation Section 4 15 2014 Ranch Rite OPERATION 9 1 Starting the Tractor The procedure to start the tractor is model specific Refer to the tractor operator s manual for starting procedures for your particular tractor Consult an authorized dealer if the starting procedure is unclear Ensure the 3 point control lever is in the lowered position and the PTO is disengaged before starting the tractor OPS U 0033 9 2 Brake and Differential Lock Setting Make sure the tractor brakes are in good operating condition Tractor brakes can be set to operate independently allowing single rear wheel braking action or locked together to provide simultaneous rear wheel braking FOR MOST DRIVING AND OPERATING CONDITIONS THE BRAKE PEDALS SHOULD BE LOCKED TOGETHER TO PROVIDE THE MOST EFFECTIVE BRAKING ACTION Always disengage the tractor differential lock when turning When engaged the differential lock will prevent or limit the tractor from turning During normal cutting conditions locking the differential Si l provides no benefit and should not be used OPS f Y Op 25 U 0013 Be aware of the operating conditions Do not operate the Tractor with weak or faulty brakes When operating down a hill or on wet or rain slick roads the braking distance increase
24. d stand to access high spots which cannot be reached from ground level Slipping and falling can cause serious injury or death sa 33 DO NOT operate this Implement on a Tractor that is not properly maintained Should a mechanical or Tractor control failure occur while operating immediately shut down the Tractor and perform repairs before resuming operation Serious injury and possible death could occur from not maintaining this Implement and Tractor in good operating condition SG 36 Safety Section 1 4 2014 Ranch Rite SAFETY A WARNING A WARNING A CAUTION A WARNING A DANGER A DANGER A WARNING HT 10 O 2014 Ranch Rite Extreme caution should be used by the Tractor operator when operating near passersby Stop raking if anyone comes within 25 feet of the Implement to prevent possible passerby injury or death from being struck from a thrown object entanglement with the rakes or run Over SRK 01 Equipment Operation Safety Instructions and Practices Never leave the Tractor and Implement unattended while the Implement is in the lifted position Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing To properly park the implement when disconnecting it from the tractor lower the stand and put the retaining pin securely in place or put a secure support under the A Frame Lower the implement carefully to the ground Do not put hands or feet under
25. death sa 2x Never allow children to play on or around Tractor or Implement Children can slip or fall off the Equipment and be injured or killed Children can cause the Implement to shift or fall crushing themselves or others sc 25 NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement Drugs and alcohol will affect an operator s alertness and coordination and therefore affect the operator s ability to operate the equipment safely Before operating the Tractor or Implement an operator on prescription or over the counter medication must consult a medical professional regarding any side effects of the medication that would hinder their ability to operate the Equipment safely NEVER knowingly allow anyone to operate this equipment when their alertness or coordination is impaired Serious injury or death to the operator or others could result if the operator is under the influence of drugs or alcohol se 27 Prolonged operation may cause operator boredom and fatigue affecting safe operation Take scheduled work breaks to help prevent these potentially impaired operating conditions Never operate the Implement and Tractor in a fatigued or bored mental state which impairs proper and safe operation sa 32 Use extreme caution when getting onto the Implement to perform repairs maintenance and when removing accumulated material Only stand on solid flat surfaces to ensure good footing Use a ladder or raise
26. der correctly and attend to appropriate maintenance The front rear left and right are determined by the normal direction of travel the same as driving an automobile HT 10 Introduction Section 2 2 2014 Ranch Rite INTRODUCTION Attention Owner Operator BEFORE OPERATING THIS MACHINE 1 Carefully read the Operator s Manual completely understand the Safety Messages and instructions and know how to operate correctly both the tractor and implement 2 Fill out the Warranty Card in full Be sure to answer all questions including the Serial Number of the Implement Mail within 30 days of delivery date of this implement NOTE Warranties are honored only if completed Owner Registration and Warranty forms are received by Ranch Rite within thirty days of delivery of the implement 3 Record the Implement Model and Serial Numbers on the Warranty page at the front of the Operator s Manual Keep this as part of the permanent maintenance file for the Implement HT 10 Introduction Section 2 3 2014 Ranch Rite ASSEMBLY SECTION Assembly Section 3 1 ASSEMBLY GENERAL ASSEMBLY Your new HT 10 Tedder is shipped partially assembled Some assembly procedures described here may have been completed Layout all components before starting and familiarize yourself with the parts by referring yourself to the parts breakdowns in this manual Assembly is highly dangerous and must be carried out in strict accordance with the followi
27. duce the possibility of tipping Use extreme caution when operating on steep slopes Keep the tractor in a low gear when going downhill DO NOT coast or free wheel downhill OPS HT 0037_A 10 OPERATING THE TRACTOR AND IMPLEMENT THE OPERATOR MUST COMPLETELY UNDERSTAND HOW TO OPERATE THE TRACTOR AND IMPLEMENT AND ALL CONTROLS BEFORE ATTEMPTING TO OPERATE The operator must read and understand the Safety and Operation Sections of the implement and tractor operator s manuals These manuals must be read and explained to any operator who cannot read Never allow someone to operate the implement and tractor without complete operating instructions Before starting any operation the operator must become familiar with the area to be worked in and any obstacles and hazards contained within to ensure safety to the operator bystanders and equipment Special attention should be paid to foreign debris rough terrain steep slopes and passersby and animals in the area OPS U 0015 HT 10 Operation Section 4 17 2014 Ranch Rite OPERATION Operating the Hay Tedder In Field Manual Fold For the HT210 manual fold lateral arms 1 amp 2 should be lowered before hand To do this rotate pin 4 so that spring pins 3 on it slides over tab C causing pin 4 to exit from the hole in the inside pipe of the strut assembly RH and LH side Now lower lateral arms 1 2 by pulling on guards A B OPS HT 0046_C USE IN THE FIELD Opre 11 Adjustmen
28. e S3PT 6 In addition to the design and configuration of this Implement including Safety Signs and Safety Equipment hazard control and accident prevention are dependent upon the awareness concern prudence and proper training of personnel involved in the operation transport maintenance and storage of the machine Refer also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals Pay close attention to the Safety Signs affixed to the Tractor and Equipment sc 18 HT 10 Safety Section 1 13 2014 Ranch Rite SAFETY Decal Location NOTE Ranch Rite supplies safety decals on this product to promote safe operation Damage to the decals may occur while in shipping use or reconditioning Ranch Rite cares about the safety of its customers operators and bystanders and will replace the safety decals on this product in the field free of charge Some shipping and handling charges may apply Contact your Bush Hog dealer to order replacement decals DL O003 HT 10 Safety Section 1 14 2014 Ranch Rite SAFETY Decal Description ITEM PART NO de 00725746 2i 3678303 3 999001 4 999200 SP 00763977 6 00786980 K 2 38332 8 2 38333 9 50063360 10 11 NFS 12 03200347 13 00776031 14 50068467C 15 10058000 16 00024100 17 02959924 HT 10 2014 Ranch Rite QTY Oo UU 0 LEVEL PELIGRO DANGER WARNING WARNING INSTRUCT IMPORTANT REFLECT RE
29. e Tractor and Hay Talle e o ES od 4 17 OPERATING THE TRACTOR ANDIMPLEMENT 00 2 a lead 4 17 Operating the Hay Tedder In Field Manual Fold coooocconccccnncnccooncnnccnnnnncnconcnnnononcnnnonancnnnonancnnonarnnonancnns 4 18 Adjustment For Correct Working Position suit ia atando 4 18 PTO REM and Groune Soe eG ings e om elle E aA 4 19 Engaging Ine Power Take OMPI San lio 4 19 SHUTTING DOW UNG APIO anssi aea cited 4 20 DISCONNECTING THE HAY TEDDER FROM THE TRACTOR cunas 4 20 HAY TEDDER STORAGE tn cee eee aea 4 21 TRANSPORTING THE TRACTOR AND IMPLEMENT siii a 4 22 Transport instructions Tor Manual Eolica ros tocaba 4 22 Transpoming on Public AOIOWEYS isa dd ii 4 23 Paulino he Tractor ANG IMpleme Miitri iaa 4 25 MAINTENANCE SEC DION ba sescisttacetscnsctessttacetearewncteitacedavatwcheiesssadesasesheivesendauveecstacessbeassec suede 5 1 ITS FAG PO Nise a le did 5 2 ROTOR PHASINC a o anole 5 2 A A haa ase esa eee a ae 5 3 RANCH RITE 1830 W 15TH STREET HOUSTON TEXAS 77008 SAFETY SECTION Safety Section 1 1 SAFETY General Safety Instructions and Practices A careful operator is the best operator Safety is of primary importance to the manufacturer and should be to the owner operator Most accidents can be avoided by being aware of your equipment your surroundings and observing certain precautions The first section of this manual includes a list of Safety Messages that if followed will help protect the operator and
30. e Tractor or Implement without supervision Make sure the operator has fully read and understood the manuals prior to operation SG 4 A WARNING shoes safety glasses and proper hearing protection at all times for protection from injury including injury from items that may be thrown by The operator and all support personnel should wear hard hats safety Yan the equipment sa 16 2 PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS Tractors with or without an Implement attached can often be noisy enough to cause permanent hearing loss We recommend that you always wear hearing protection if the noise in A CAUTION the Operator s position exceeds 80db Noise over 85db over an extended period of time will cause severe hearing loss Noise over 90db adjacent to the Operator over an extended period of time will cause permanent or total hearing loss NOTE Hearing loss from loud noise from tractors chain saws radios and other such sources close to the ear is cumulative over a lifetime without hope of natural recovery sa 17 HT 10 Safety Section 1 3 2014 Ranch Rite SAFETY A WARNING A DANGER A DANGER A DANGER A WARNING A WARNING A DANGER HT 10 Always read carefully and comply fully with the manufacturer s instructions when handling oil solvents cleansers and any other chemical agent sc 22 KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement o and possible serious injury or
31. ed at a Dealer If oil does penetrate the skin have the injury treated immediately by a physician knowledgeable and skilled in this procedure se 15 Never run the Tractor engine in a closed building or without adequate ventilation The DANGER de exhaust fumes can be hazardous to your health sa 23 Do not exceed the rated PTO speed for the Implement Excessive PTO speeds can cause As ital Implement driveline or blade failures resulting in serious injury or death sc 26 Operate the Tractor and or Implement controls only while properly seated in the Tractor seat A DANGER with the seat belt securely fastened around you Inadvertent movement of the Tractor or Implement may cause serious injury or death sc 29 In case of mechanical difficulty during operation place the transmission in the park A WARNING position set the parking brake shut down all power including the PTO and the engine and remove the key Wait until all rotating motion has stopped before dismounting sc sg Do Not operate this equipment in areas where insects such as bees may attack you and or cause you to lose control of the equipment If you must enter in such areas use a tractor with an enclosed Cab and close the windows to prevent insects from entering If a tractor A WARNING cab is not available wear suitable clothing including head face and hand protection to shield you from the insects Attacking insects can cause you to lose control of the tractor wh
32. ed operator has read and understands the implement and tractor Operator s Manuals and is experienced in implement and tractor operation and all associated safety practices In addition to the safety messages contained in this manual safety signs are affixed to the implement and tractor If any part of the operation and safe use of this equipment is not completely understood consult an authorized dealer for a complete explanation If the operator cannot read the manuals for themselves or does not completely understand the operation of the equipment it is the responsibility of the supervisor to read and explain the manuals safety practices and operating instructions to the operator Safe operation of equipment requires that the operator wear approved Personal Protective Equipment PPE for the job conditions when attaching operating servicing and repairing the equipment PPE is designed to provide operator protection and includes the following safety wear PERSONAL PROTECTIVE EQUIPMENT PPE e Always Wear Safety Glasses e Hard Hat e Steel Toe Safety Footwear e Gloves e Hearing Protection e Close Fitting Clothing e Respirator or Filter Mask depends on operating conditions OPS U 0002 I 0 3 NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement Drugs and alcohol will affect an operator s alertness and coordination and therefore affect the operator s ability to operate the equipment sa
33. eight A minimum of 20 total tractor weight must be maintained on the tractor front end at all times Front end weight is critical to maintain steering control and to prevent the tractor from rearing up while driving If the front end is too light add weight until a minimum of 20 total weight is reached on the front tires Front weights and weight carriers can be purchased through an authorized tractor dealership OPS U 0005 4 GETTING ON AND OFF THE TRACTOR Before getting onto the tractor the operator must read and completely understand the implement and tractor operator manuals If any part of either manual is not completely understood consult an authorized dealer for a complete explanation OPS U 0007 Do not mount or dismount the Tractor while the tractor is moving Mount the Tractor only when the Tractor and all moving parts are completely stopped sa 12 A WARNING 4 1 Boarding the Tractor Use both hands and equipped handrails and steps for support when boarding the tractor Never use control levers for support when mounting the tractor Seat yourself in the operator s seat and secure the seat belt around you Never allow passengers to ride on the tractor or attached equipment Riders can easily fall off and be seriously injured or killed from falling off and being ran over It is the operator s responsibility to forbid all extra riders at all times OPS U 0008 HT 10 Operation Section 4 5 2014 Ranch Rite OPERATION
34. ent running efficiently and safely read your manual thoroughly and follow these directions and the Safety Messages in this Manual The Table of Contents clearly identifies each section where you can easily find the information you need The OCCUPATIONAL SAFETY AND HEALTH ACT 1928 51 Subpart C makes these minimum safety requirements of tractor operators REQUIRED OF THE OWNER 1 Provide a Roll Over Protective Structure that meets the requirements of this Standard and 2 Provide Seat belts that meet the requirements of this paragraph of this Standard and SAE J4C and 3 Ensure that each employee uses such Seat belt while the tractor is moving and 4 Ensure that each employee tightens the Seat belt sufficiently to confine the employee to the protected area provided by the ROPS REQUIRED OF THE OPERATOR Securely fasten seat belt if the tractor has a ROPS Where possible avoid operating the tractor near ditches embankments and holes Reduce speed when turning crossing slopes and on rough slick or muddy surfaces Stay off slopes too steep for safe operation Watch where you are going especially at row ends on roads and around trees Do not permit others to ride Operate the tractor smoothly no jerky turns starts or stops Hitch only to the drawbar and hitch points recommended by the tractor manufacturer When the tractor is stopped set brakes securely and use park lock if available OMONDOAWD Keep child
35. eration or repair sc 1 READ UNDERSTAND and FOLLOW the following Safety Messages Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages Always use good common sense to avoid hazards sa LEA El i Si no lee ingles pida ayuda a alguien que si lo lea para que le traduzca las WSTRUCTINO A PELIGRO Medidas de seguridad sa HT 10 Safety Section 1 2 O 2014 Ranch Rite SAFETY Engine Exhaust some of its constituents and certain vehicle components contain or emit A WARNING chemicals known to the state of California to cause cancer and birth defects or other reproductive harm sa 0 Battery posts terminals and related accessories contain lead and lead compounds A WARNING chemicals known to the state of California to cause cancer birth defects or other reproductive harm sa 31 A WARNING Always maintain the safety signs in good readable condition If the safety signs are missing damaged or unreadable obtain and install replacement safety signs immediately sc 5 Operator Safety Instructions and Practices Never operate the Tractor or Implement until you have read and completely understand this Manual the Tractor Operator s Manual and each of the Safety Messages found in the Manual or on the Tractor and A DANGER implement Learn how to stop the tractor engine suddenly in an emergency Never allow inexperienced or untrained personnel to operate th
36. fely Before operating the Tractor or Implement A DANGER an operator on prescription or over the counter medication must consult a medical professional regarding any side effects of the medication that would hinder their ability to operate the Equipment safely NEVER Knowingly allow anyone to operate this equipment when their alertness or coordination is impaired Serious injury or death to the operator or others could result if the operator is under the influence of drugs or alcohol sc 27 HT 10 Operation Section 4 3 2014 Ranch Rite OPERATION 3 TRACTOR REQUIREMENTS The tractor used to operate the tedder must have the power capacity to lift pull and operate the Power Take Off PTO at the tedder s rated speed while traveling at a ground speed between 2 and 5 MPH Operating the tedder with a tractor that does not meet the following requirements may cause tractor or tedder damage and be a potential danger to the operator and passersby Tractor Requirements and Capabilities Tractor Requirements and Capabilities e ASABE approved Roll Over Protective Structure ROPS or ROPS cab and seat belt e Tractor Safety Devices Slow Moving Vehicle SMV emblem lighting PTO master shield e Tractor HOrSepoWer ocoooncccnccnccnncnnmo 15 HP Minimum 3 1 ROPS and Seat Belt The tractor must be equipped with a Roll Over Protective Structure ROPS tractor cab or roll bar and seat belt to protect the operator from fallin
37. g off the tractor especially during a roll over where the driver could be crushed and killed Only operate the tractor with the ROPS in the raised position and seat belt fastened Tractor model not equipped with a ROPS and seat belt should have these life saving features installed by an authorized dealer OPS U 0003 Operate this Equipment only with a Tractor equipped with an approved roll A WARNING 0ver protective system ROPS Always wear seat belts Serious injury or even death could result from falling off the tractor particularly during a turnover when the operator could be pinned under the ROPS sc 7 3 2 Tractor Horsepower The power required to operate a implement is determined by the tractor PTO horsepower For most operating conditions the HT 10 requires a tractor with at least 15hp Operating the implement with a tractor that does not have adequate power may damage the tractor engine Exceeding the recommended horsepower may cause damage by overpowering the unit in heavy operating conditions HT 10 Operation Section 4 4 O 2014 Ranch Rite OPERATION 3 3 Drawbar Pull Type Mower For pull tyoe mowers 540 and 1000 RPM l equipped with an equal angle driveline the tractor l M if bd A e N Y drawbar must be positioned at a 14 distance from the hitch point to the PTO shaft end for proper operation and minimal wear to the driveline and tractor K Albii Bechet Diii ety iai pee ABAE 8398 j DH 3 4 Front End W
38. ge with reflective red trim for both easy day and night visibility Make sure the SMV sign is clean and visible from the rear of the unit before transporting the tractor and implement on a public roadway Replace the SMV emblem if faded damaged or no longer reflective OPS U 0020 Make sure that all tractor flashing warning lights headlights and brake tail lights are functioning properly before proceeding onto public roads While newer model tractors have plenty of lighting to provide warning signals and operating lighting most older models are only equipped with operating lights Consult an authorized tractor dealer for lighting kits and modifications available to upgrade the lighting on Fa older tractor models OPS U 0021 When operating on public roads have consideration for other road users Pull to the side of the road occasionally to allow all following traffic to pass Do not exceed the legal speed limit set in your country for agricultural tractors Always stay alert when transporting the tractor and implement on public roads Use caution and reduce speed if other vehicles or pedestrians are in the area OPS U 0022 HT 10 Operation Section 4 24 O 2014 Ranch Rite OPERATION Reduce speed before turning or applying the brakes Ensure that both brake pedals are locked together ia when operating on public roads OPS U 0023 14 3 Hauling the Tractor and Implement Before transporting a loaded tractor and impleme
39. gy conditions where you cannot clearly see at least 100 yards in front and to the sides of the tractor and implement Make sure that you can clearly see and identify passersby steep slopes ditches drop offs overhead obstructions power lines debris and foreign objects If you are unable to clearly see this type of items discontinue operating this equipment s3PT 21 Safety Section 1 5 SAFETY Operate this Equipment only with a Tractor equipped with an approved roll over protective system ROPS Always wear seat belts Serious injury or even death could result from falling off the tractor particularly during a turnover when the operator could be pinned under the ROPS c 7 A WARNING Do not modify or alter this Implement Do not permit anyone to modify or alter this Pedi lb Implement any of its components or any Implement function se s BEFORE leaving the tractor seat always set the parking brake and or set ENGINE the tractor transmission in parking gear disengage the PTO stop the engine remove the key and wait for all moving parts to stop Place the tractor shift lever into a low range or parking gear to prevent the tractor from rolling Never dismount a Tractor that is moving or while the engine is running Operate the Tractor controls from the tractor seat only sc 9 A DANGER Never allow children or other persons to ride on the Tractor or Implement A DANGER Falling off can result in serious injury or death
40. he tractor owner s manual for tractor starting procedures Only start the tractor while seated and belted in the tractor operator s seat Never bypass the ignition switch by short circuiting the starter solenoid After the tractor engine is running avoid accidental contact with the tractor transmission to prevent sudden and unexpected tractor movement OPS U 0028 Never run the Tractor engine in a closed building or without adequate ventilation The A DANGER o haustfumes can be hazardous to your health sa 23 Start tractor only when properly seated in the Tractor seat Starting a A DANGER tractor in gear can result in injury or death Read the Tractor operators manual for proper starting instructions sa 13 Start andy from seat in park or nera Saring de quer kilig 6 CONNECTING THE HAY TEDDER TO THE TRACTOR Use extreme caution when connecting the hay tedder to the tractor The hay tedder should be securely resting at ground level or setting on blocks Keep hands and feet from under the hay tedder and clear of pinch points between the tractor hitch arms and lift side rotors OPS HT 0011 HT 10 Operation Section 4 7 2014 Ranch Rite OPERATION Always shut the Tractor completely down place the transmission in park and set the A DANGER parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches sspt 15 6 1 Connecting the Hay Tedder The attachment of pull type ma
41. ich can result in serious injury or death to you or bystanders Never dismount a moving tractor sG 40 HT 10 Safety Section 1 7 2014 Ranch Rite SAFETY A WARNING A DANGER Objects such as wire cable rope and chain can become entangled in the rotating parts of the raking components causing mechanical damage Entangled items caught in the rakes can sling outward possibly injuring or entangling the operator or passersby Any objects that might become entangled in a raking component should be removed from the area before operating the rake srk 02 DO NOT allow any person under a folded wing unless wing is securely locked up or supported DO NOT approach the Implement unless the lee Tractor is turned off and all motion has ceased Never work under the frame work or any lifted component unless the implement is securely supported or blocked up A sudden or inadvertent fall by any of these components could cause serious injury or even death sT 03 Connecting or Disconnecting Implement Safety Instructions amp Practices A WARNING A DANGER A DANGER A WARNING HT 10 The rotating parts of this machine continue to rotate even after the PTO has been turned off The operator should remain in his seat for 60 seconds after the brake has been set the PTO disengaged the tractor turned off and all evidence of rotation has ceased sspt 10 Wait a minute Save a life DO NOT use a PTO adapter to attach a n
42. implement and tractor operation and all associated safety practices before operating the implement and tractor Proper operation of the implement as detailed in this manual will help ensure years of safe and satisfactory use of the hay tedder READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND IMPLEMENT If you do not understand any of the instructions contact your nearest authorized dealer for a full explanation Pay close attention to all safety signs and safety messages contained in this manual and those affixed to the implement and tractor OPS U 0001 READ UNDERSTAND and FOLLOW the following Safety Messages Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the e Safety Messages Always use good common sense to avoid hazards sc 2 1 Standard Equipment and Specifications HT 10 Number of Rotors 2 Number of Arms 12 Number of Double Tines 12 Horsepower Requirements 15 Min Working Width 10 Transport Width Approximate 10 Weight Approximate 385 lbs Tire Size 15 00 x 6300 6 Number of Tires 2 PTO Folding Mechanism Working Speed HT 10 2014 Ranch Rite 540 RPM 1 3 8 Spline w Slipclutch Spring Assist 5 MPH Operation Section 4 2 OPERATION 2 OPERATOR REQUIREMENTS Safe operation of the unit is the responsibility of a qualified operator A qualifi
43. injuries can result from operating this equipment at high speeds Understand the Tractor and Implement and how it handles before transporting on streets and highways Make sure the Tractor steering and brakes are in good condition and operate properly Before transporting the Tractor and Implement determine the proper transport speeds for you and the equipment Make sure you abide by the following rules Test the tractor at a slow speed and increase the speed slowly Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement As you increase the speed of the Tractor the stopping distance increases Determine the maximum transport speed not to exceed 20 mph 30 kph for transporting this equipment Test the equipment at a slow speed in turns Increase the speed through the turn only after you determine that the equipment can be operated at a higher speed Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over Determine the maximum turning speed for you and this equipment before operating on roads or uneven ground Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment Be aware of the operating conditions Do not operate the Tractor with weak or faulty brakes or worn tires When operating down a hill or on wet or rain slick roads the braking distance increases use extreme care and reduce your spee
44. is in good condition The drawbar pins are securely in place The PTO master shield is in place The engine oil level is full The brake fluid level is full The power steering fluid level is full The fuel level is adequate The engine coolant fluid level is full The radiator is free of debris The air filter is in good condition Operator s Signa ture DO NOT OPERATE an UNSAFE TRACTOR or IMPLEMENT HT 10 Operation Section 4 14 2014 Ranch Rite OPERATION 9 DRIVING THE TRACTOR AND IMPLEMENT Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and precautions to take while driving with an attached implement Ensure the tractor has the capacity to handle the weight of the implement and the tractor operating controls are set for safe transport To ensure safety while driving the tractor with an attached implement review the following OPS U 0012 This Implement may be wider than the Tractor Be careful when operating or transporting this equipment to prevent the Implement from running into or striking sign posts guard rails A DANGER concrete abutments or other solid objects Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control serious injury or even death Never allow the Implement to contact obstacles sspt 12 Transport only at speeds where you can maintain control of the A WARNING quipment Serious accidents and
45. lifted components S3PT 1 Do not back up with this implement Backing could damage the machine or its components S3PT 4 Use extreme care when lowering or unfolding the implement s wings Make sure no bystanders are close by or underneath the wings Allow ample clearance around the implement when folding or unfolding the wings Use extreme caution around buildings or overhead power lines S3PT 05 There are obvious and hidden potential hazards in the operation of this Implement as in all power driven or pulled equipment REMEMBER This machine is often operated in rough terrain conditions that include tall grass weeds gullies holes slopes hidden obstructions and the like Serious injury or even death may occur unless care is taken to assure the safety of the operator and bystanders in the area Do not operate this machine with anyone in the immediate area sspt 07 This Implement may be wider than the Tractor Be careful when operating or transporting this equipment to prevent the Implement from running into or striking sign posts guard rails concrete abutments or other solid objects Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control serious injury or even death Never allow the Implement to contact obstacles sspt 12 Operate this Implement only in conditions where you have clear visibility in daylight or with adequate artificial lighting Never operate in darkness or fog
46. ming repairs and service Require that the employee operator stop operation if bystanders or passersby come within 25 feet Child Labor Under 16 Years of Age Some regulations specify that no one under the age of 16 may operate power machinery It is your responsibility to know what these regulations are in your own area or situation Refer to U S Dept of Labor Employment Standard Administration Wage amp Home Division Child Labor Bulletin 102 HT 10 Safety Section 1 19 2014 Ranch Rite INTRODUCTION SECTION Introduction Section 2 1 INTRODUCTION The HT 10 Hay Tedder is one of the fastest and most efficient hay tedders available Rotor speed and forward drive speed should be selected for each individual job since there are large variations in the nature and properties of different crops This HT 10 Hay Tedder is designed with care and built with quality materials by skilled workers Proper assembly maintenance and operating practices as described in this manual will help the owner operator get years of satisfactory service from the machine The purpose of this manual is to familiarize instruct and train The Assembly Section instructs the owner operator in the correct assembly of the tedder using standard and optional equipment Careful use and timely service saves extensive repairs and costly down time losses The Operation and Maintenance sections of the manual trains the owner operator how to work the ted
47. nd wait for all machine movement to stop before servicing adjusting cleaning or unclogging the equipment except where the machine must be running to be properly serviced or maintained in which case the employer shall instruct employees as to all steps and procedures which are necessary to safely service or maintain the equipment Make sure everyone is clear of machinery before starting the engine engaging power or operating the machine Employer Responsibilities To ensure employee safety during Tractor and Implement operation it is the employer s responsibility to 1 2 3 4 8 Train the employee in the proper and safe operation of the Tractor and Implement Require that the employee read and fully understand the Tractor and Implement Operator s manual Permit only qualified and properly trained employees to operate the Tractor and Implement Maintain the Tractor and Implement in a safe operational condition and maintain all shields and guards on the equipment Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee operator securely fasten the safety belt and operate with the ROPS in the raised position at all times Forbid the employee operator to carry additional riders on the Tractor or Implement Provide the required tools to maintain the Tractor and Implement in a good safe working condition and provide the necessary support devices to secure the equipment safely while perfor
48. ng instructions We recommend that qualified personnel perform assembly It is highly recommended that assembly be carried out in a flat solid surface open area with no people particularly children nearby who could be severely be injured if they were to touch or move any parts of the machine When assembling the implement provide suitable lifting mechanisms and supports to stabilize the partially assembled implements This will prevent them from falling and causing damage to the implement or serious injury The steps for assembly are illustrated in the following pages Depending on the experience of the assemblers and the tools available it is not necessary that the instructions be followed in the exact order given here but the safety precautions described above must always be followed carefully and scrupulously Make sure the area around the machine is clear before lowering the wings Do not lower the A CAUTION _ tedder wings when people or pets are near the rotary tedder or folding mechanism The tedder must be attached to the tractor when the wings are folded Always use safety stands or blocking in conjunction with hydraulic jacks or joists Do not rely A WARNING on the jack or joist to carry the load They could fail AXLE INSTALLATION 1 Position the mainframe upside down as indicated in Asm HT 0001 2 Rotate the gearbox rotors 1 amp 2 so that one disc s holes line up with the main axis of the frame 7 while the other disc s h
49. nt measure the height and width dimensions and gross weight of the complete loaded unit Ensure that the load will be in compliance with the legal limits set for the areas that will be traveled through OPS U 0024 Use adequately sized and rated trailers and equipment to transport the tractor and implement Consult an authorized dealer to determine the proper equipment required Using adequately sized chains heavy duty straps cables and or binders securely tie down both the front and rear of the tractor utilizing the proper tie down locations as specified by the tractor manufacturer OPS U 0025 HT 10 Operation Section 4 25 2014 Ranch Rite MAINTENANCE SECTION Maintenance Section 5 1 MAINTENANCE Although very little can go wrong with the machine in normal working conditions a regular inspection of moving parts is advisable to obtain a full working life LUBRICATION La 2 3 4 Lubricate the IID shaft after every 5 hours of use Lubricate all grease fitting locations on the center section rotating parts and any other parts after every 10 hours of use Check the grease level in the gearbox each working day Use Multi Purpose Gear Oil 00786250 when necessary Fill to level plug After every 10 hours of operation check all bolts nuts and tines Tighten as needed The Center Main Gearbox should be lubricated after 50 working hours Use Multi Purpose A IMPORTANT Gear Oil P N 00786250 How to Lubricate
50. oles are spaced equal distance from the mainframe 5 amp 6 3 Remove the roll pin from the gearbox spindle and discard the spacer Install axle on spindle as indicated on Asm HT 0001 and fasten axle to spindle using large roll pin previously removed and second roll pin driven through the center of the larger roll pin Ase 270001 HT 10 Assembly Section 3 2 2014 Ranch Rite ASSEMBL Y TIRE 8 WHEEL ASSEMBLIES INSTALLATION 1 2 3 Install large anti wrap shield 1 on axle first Install Tire and Wheel Assembly next Install small dust cover 2 next and then fasten with washer 3 and nut 4 Tighten nut to 45 Ft Lbs Asm H T 0002 DRAWBAR amp SHIELDS INSTALLATION Lift unit and position upright Supporting the unit with safety stands or blocking to prevent unit from falling 2 Install drawbar on mainframe aligning drawbar pivot holes A with mainframe lugs B and installing pivot pin 3 through both 3 Retain pivot pin 3 with two cotter pins 6 4 Insert pivot lug of angle adjustment handle 8 into pivot hole 9 on drawbar and retain with cotter pin 6 Attach fork end of angle adjustment handle 7 to lugs D on main frame using pin 4 and two cotter pins 6 5 Attach PTO Shield 14 to main gearbox using 2 nuts 12 Asm HT 0003 HT 10 Assembly Section 3 3 2014 Ranch Rite ASSEMBL Y TINE ASSEMBLIES INSTALLATION Note Two bundles of tines have been shipped with each HT
51. on matching Implement driveline to a Tractor PTO Use of an adapter can double the operating speed of the Implement resulting in excessive vibration thrown objects and blade and implement failure Adapter use will also change the working length of the driveline exposing unshielded driveline areas Serious bodily injury and or equipment failure can result from using a PTO adapter Consult an authorized dealer for assistance if the Implement driveline does not match the Tractor PTO S3PT 14 Always shut the Tractor completely down place the transmission in park and set the parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches S3PT 15 When attaching the Implement input driveline to the Tractor PTO it is important that the connecting yoke spring activated locking collar slides freely and the locking balls are seated securely in the groove on the Tractor PTO shaft Push and pull the driveline back and forth several times to ensure it is securely attached A driveline not attached correctly to the Tractor PTO shaft could come loose and result in personal injury and damage to the Implement S3PT 17 Safety Section 1 8 O 2014 Ranch Rite SAFETY A WARNING A WARNING A CAUTION A WARNING A WARNING A WARNING HT 10 Before operating the Implement check to make sure the Implement input driveline will not bottom out or become disengaged Bottoming out occurs when the inner sh
52. onnection bolts pins are tight Transport locks amp retaining chains are in good condition Rake spokes are in good condition amp securely attached Rake Wheels are securely attached to the frame members The Hydraulic Cylinders are in good condition The Hydraulic Cylinder pins are in place amp retained There are no leaking or damaged hoses There is no evidence of hydraulic leaks The tires amp wheel s are in good condition Wheel lug nuts are tight Operator s Signature DO NOT OPERATE an UNSAFE TRACTOR or TEDDER HT 10 Operation Section 4 13 2014 Ranch Rite OPERATION Tractor PRE OPERATION Inspection Tractor ID Make RANCH R ITE Date Shift Before conducting the inspection make sure the tractor engine is off all rotation has stopped and the tractor is in park with the parking brake engaged Make sure the implement is resting on the ground or securely blocked up and all hydraulic pressure has been relieved A WARNING Condition at Specific Comments if Start of Shift not O K Item The flashing lights function properly The SMV Sign is clean and visible The tires are in good condition with proper pressure The wheel lug bolts are tight The tractor brakes are in good condition The steering linkage is in good condition There are no visible oil leaks The hydraulic controls function properly The ROPS or ROBS Cab is in good condition The seatbelt is in place and in good condition The 3 point hitch
53. or uneven surfaces to prevent loss of steering control which could result in property damage or possible injury Do not transport unless 3 Point lift lever is fully raised and in the latched transport position Dropping implement in transport can cause serious damage to the tractor and or Implement and possibly cause the operator or others to be injured or killed S3PT 02 Allow sufficient clearance for the Implement to swing outward while turning Implements carried behind the Tractor will swing outside the tire path when making turns Contacting a solid object while turning will cause equipment damage and possible injury S3PT 20 Make certain that the Slow Moving Vehicle SMV sign is installed in such a way as to be clearly visible and legible When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations se s Safety Section 1 9 2014 Ranch Rite SAFETY Transport only at speeds where you can maintain control of the A WARNING equipment Serious accidents and injuries can result from operating this equipment at high speeds Understand the Tractor and Implement and how it handles before transporting on streets and highways Make sure the Tractor steering and brakes are in good condition and operate properly Before transporting the Tractor and Implement determine the proper transport speeds for you and the equipment Make sure you abide by the following rules Te
54. r Implement rel A DANGER Falling off can result in serious injury or death sa 10 14 1 Transport Instructions for Manual Fold Before transporting the implement it is necessary raise lateral arms 1 amp 2 To do this first check that spring pin 4 is not touching tab C RH and LH side Then raise lateral arms 1 amp 2 by pulling on guards A B until pin 4 of the spring strut assembly enters hole D RH and LH side of the inside pipe of the strut assembly OPS HT 0055_A TANSPOAT INTRUCTIONS FOR MANUAL FOLD Op 277 HT 10 Operation Section 4 22 2014 Ranch Rite OPERATION Before transporting the tractor on a public roadway or boarding a trailer for transport the tractor brake pedals should be locked together Locking the pedals ensures that both wheels brake simultaneously while stopping especially when making an emergency stop Use extreme caution and avoid hard applications of the tractor brakes when towing heavy loads at road sf e Wi speeds Never tow the implement at speeds greater than 20 MPH 25 kph OPS U 0018 Visa 14 2 Transporting on Public Roadways Extreme caution should be used when transporting the tractor and implement on public roadways The tractor must be equipped with all required safety warning features including a SMV emblem and flashing warning lights to alert drivers of the tractor s presence Remember that roadways are primarily designed for automotive drivers and most drivers
55. r Pre Operation Inspection Service e vr en AL Refer to the tractor operator s manual to ensure a F ae pee ee complete pre operation inspection and scheduled w A service is performed according to the 200 manufacturers recommendations The following Ca are some of the items that require daily service and be inspection bs e Tire condition air pressure e Wheel lug bolts e Steering linkage e PTO shield e SMV sign is clean and visible e Tractor s lights are clean and functional e Tractor Seat belt is in good condition e Tractor ROPS is in good condition e ROPS is in the raised position e No tractor oil leaks e Radiator free of debris e Engine oil level and condition e Engine coolant level and condition e Power brake fluid level e Power steering fluid level e Fuel condition and level e Sufficient lubrication at all lube points e Air filter condition OPS U 0030 HT 10 Operation Section 4 11 2014 Ranch Rite OPERATION 8 2 Hay Tedder Pre Operation Inspection Service Before each use a complete inspection and service is required to ensure the hay tedder is in a good and safe working condition Damaged and or broken parts should be repaired and or replaced immediately To ensure the hay tedder is ready for operation conduct the following OPS HT 0020 The operators manual and safety signs affixed on the unit contain important instructions on the safe and proper use of the equipment Maintain these
56. ren away from danger all day every day Equip tractors with rollover protection ROPS and keep all machinery guards in place Please work drive play and live each day with care and concern for your safety and that of your family and fellow citizens AAA 1830 W 15th Street HAY TEDDER Houston Texas 77008 HT 10 O 2014 Ranch Rite P N 50068746C Printed U S A
57. s A sudden movement could cause injury or even amputate fingers KEEP CHILDREN AWAY WHEN MAKING ADJUSTMENTS seL s Always maintain the safety signs in good readable condition If the safety signs are missing WARNING i damaged or unreadable obtain and install replacement safety signs immediately sc 5 HT 10 Safety Section 1 11 2014 Ranch Rite SAFETY A WARNING A DANGER A WARNING A WARNING A WARNING A WARNING HT 10 Do not modify or alter this Implement Do not permit anyone to modify or alter this Implement any of its components or any Implement function sas Never work under the Implement the framework or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death sc 14 Never attempt to lubricate adjust or remove material from the Implement while it is in motion or while tractor engine is running se 20 Periodically inspect all moving parts for wear and replace when necessary with authorized service parts Look for loose fasteners worn or broken parts and leaky or loose fittings Make sure all pins have cotter pins and washers Serious injury may occur from not maintaining this machine in good working order sa 21 Perform service repairs and lubrication according to the maintenance section Ensure the unit is properly lubricated as specified in the lubrication schedule
58. s use A WARNING extreme care and reduce your speed in these conditions When operating in traffic always use the Tractor s flashing warning lights and reduce your speed Be aware of traffic around you and watch out for the other guy HT 10 Operation Section 4 16 2014 Ranch Rite OPERATION 9 3 Driving the Tractor and Hay Tedder Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the tractor and implement Moving slowly at first will also prevent the tractor from rearing up and loss of steering control The tractor should never be operated at speeds that cannot be safely handled or which will prevent the operator from stopping quickly during an emergency If the power steering or engine ceases operating stop the tractor immediately as the tractor will be difficult to control Perform turns with the tractor and implment at slow speeds to determine how the tractor with an attached implement handles a turn Determine the safe speed to maintain proper control of the tractor when making turns When turning with a towed implement the overall working length of the unit is increased Allow additional clearance for the implement when turning To avoid overturns drive the tractor with care and at safe speeds especially when operating over rough ground crossing ditches or slopes and turning corners Tractor wheel tread spacing should be increased when working on inclines or rough ground to re
59. se points and fill gearbox oil levels as detailed in the maintenance section e Tighten all bolts and pins to the recommended torque e Check worn and damaged parts Perform repairs and make replacements immediately so that the implement will be ready for use at the start of the next season e Store the hay tedder in a clean dry place with the housing resting securely on blocks or at ground level e Use spray touch up enamel where necessary to prevent rust and maintain the appearance of the hay tedder Store tedder with the wings lowered and the main transport wheels lowered OPS HT 0053 Never allow children to play on or around Tractor or Implement Children can slip or fall off A DANGER the Equipment and be injured or killed Children can cause the Implement to shift or fall crushing themselves or others sc 25 HT 10 Operation Section 4 21 2014 Ranch Rite OPERATION 14 TRANSPORTING THE TRACTOR AND IMPLEMENT Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind when you finish working in an area Therefore the operator must employ good judgement and safe operation practices when transporting the tractor and implement between locations By using good judgement and following safe transport procedures the possibility of accidents while moving between locations can be substantially minimized OPS U 0017 Never allow children or other persons to ride on the Tractor o
60. shift lever into a low range or parking gear to prevent the tractor from rolling Never dismount a Tractor that is moving or while the engine is running Operate the Tractor controls from the tractor seat only sc 9 BEFORE leaving the tractor seat always set the parking brake and or set Fr ES fr FO si 1 SUS TE ul HT 10 Operation Section 4 6 2014 Ranch Rite OPERATION 5 STARTING THE TRACTOR The operator must have a complete understanding of the placement function and operational use of all tractor controls before starting the tractor Review the tractor operator s manual and consult an authorized dealer for tractor operation instructions if needed Essential Tractor Controls e Locate the light control lever e Locate the engine shut off control e Locate the brake pedals and the clutch e Locate the PTO control e Locate the 3 point hitch control lever e Locate the hydraulic remote control levers Before starting the tractor ensure the following e Conduct all pre start operation inspection and service according to the tractor operator s manual e Make sure all guards shields and other safety devices are securely in place e The parking brake is on e The PTO control lever is disengaged e The 3 point hitch control lever is in the lowered position e The hydraulic remote control levers are in the neutral position e The tractor transmission levers are in park or neutral Refer to t
61. st the tractor at a slow speed and increase the speed slowly Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement As you increase the speed of the Tractor the stopping distance increases Determine the maximum transport speed not to exceed 20 mph 30 kph for transporting this equipment Test the equipment at a slow speed in turns Increase the speed through the turn only after you determine that the equipment can be operated at a higher speed Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over Determine the maximum turning speed for you and this equipment before operating on roads or uneven ground Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment Be aware of the operating conditions Do not operate the Tractor with weak or faulty brakes or worn tires When operating down a hill or on wet or rain slick roads the braking distance increases use extreme care and reduce your speed When operating in traffic always use the Tractor s flashing warning lights and reduce your speed Be aware of traffic around you and watch out for the other guy sa 19 Be particularly careful when transporting the Implement using the tractor Turn curves or go up or down hills only at a low speed and at a gradual steering angle Make certain that at least 20 of the tractor s weight is on the fron
62. t For Correct Working Position These machines are very easily adjusted For best operation the tines 1 on the front side of the machine should brush the ground To obtain this turn the adjustment crank 2 HT 10 Operation Section 4 18 2014 Ranch Rite OPERATION 11 1 PTO RPM and Ground Speed Ground speed will depend upon the height type and density of vegetation Recommended speed for efficient performance is 5 mph Operate the implement at its 350 450 PTO RPM 540 MAX rated speed to maintain good operation Refer to the tractor operator s manual or the tractor instrument panel for the engine speed and gear to provide the required PTO and desired ground speed Make sure that the implement is operating at its full rated speed before entering into use If it becomes necessary to temporarily regulate engine speed increase or decrease the throttle gradually Ground speed is achieved by transmission gear selection and not by the engine operating speed The operator may be required to experiment with several gear range combinations to determine the best gear and range which provides the most ideal performance from the implement and most efficient tractor operation As the severity of conditions increase the ground speed should be decreased by selecting a lower gear to maintain the proper operating PTO speed OPS HT 0025 11 2 Engaging the Power Take Off PTO Before engaging the PTO make certain that the area is clear of bystanders and p
63. t resting securely on the ground block the hay tedder up securely before attempting to disconnect it from the tractor Use extreme care to keep feet and hands from under the hay tedder and clear of any pinch points OPS HT 0051 Always shut the Tractor completely down place the transmission in park and set the A DANGER parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches s3PT 15 HT 10 Operation Section 4 20 2014 Ranch Rite OPERATION Before disconnecting the machine from the tractor use the hydraulic lever to unfold and lower the E machine completely apply the brake and shut off the tractor Relieve hydraulic pressure by moving the control levers back and forth several times Dismount from the tractor and place the parking stand in the vertical position Turn the crank to raise the machine from the drawbar so that the hitch pin may be removed from the tractor Disconnect the quick release coupling Disconnect the driveline and rest on the driveline holder The tractor can now be moved away OPS HT 0052 D SY i Op 263 gt 13 HAY TEDDER STORAGE Properly preparing and storing the hay tedder at the end of the season is critical to maintaining its appearance and to help ensure years of dependable service The following are suggested storage procedures e Thoroughly clean all debris off the implement to prevent damage from decaying grass e Lubricate all grea
64. t wheels to maintain safe steerage Slow down on rough or uneven surfaces sri 01 A DANGER When the Wings are folded for transport the center of gravity is raised and the possibility of overturn is increased Drive slowly and use extreme caution when turning on hillsides A DANGER Overturning the Implement could cause the Implement to overturn the Tractor and vice versa resulting in serious injury or even death Never fold wings on a hillside the Implement may overturn sti 02 Only tow the Implement behind a properly sized and equipped Tractor which exceeds the weight of the Implement by at least 20 DO NOT A WARNING tow the Implement behind a truck or other type of vehicle Never tow the Implement and another Implement connected in tandem Never tow the Implement at speeds over 20 MPH sri 06 HT 10 Safety Section 1 10 2014 Ranch Rite SAFETY Secure the Implement for transport before traveling on public roads For pull type Implements secure the center axle using cylinder stops or transport pin and properly attach A WARNING a safety chain between the Implement and Tractor Secure wings in upright position on folding Implements using wing transport locks srt 7 Always keep a careful lookout and use extreme care when working around overhead obstructions and electrical power lines The Implement wing can be over 10 feet high Never allow the Implement wing to come within 10 feet of any power line sri s A WARN
65. talled in the equipment covered by this limited warranty are warranted for ninety 90 days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period whichever occurs later Warranted parts shall be provided at no cost to the user at an authorized Ranch Rite dealer during regular working hours Ranch Rite reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship DISCLAIMER OF IMPLIED WARRANTIES 8 CONSEQUENTIAL DAMAGES Ranch Rite s obligation under this limited warranty to the extent allowed by law is in lieu of all warranties implied or expressed INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted Such incidental and consequential damages shall include but not be limited to transportation charges other than normal freight charges cost of installation other than cost approved by Ranch Rite duty taxes charges for normal service or adjustment loss of crops or any other loss of income rental of substitute equipment expenses due to loss damage detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Ranch Rite THIS LIMITED WARRANTY SHALL NOT APPLY 1 To vendor items which carry their own warranties such as engines tires and tubes 2 If
66. will not be looking out for you therefore you must look out for them Check your side view mirrors frequently and remember that vehicles will approach quickly because of the tractor s slower speed Be extremely cautious when the piece of equipment that you are towing is wider than the tractor tire width and or extends beyond your lane of the road Make sure that a proper size safety tow chain is secured between the tractor and implement before entering a public road OPS U 0019 Only tow the Implement behind a properly sized and equipped Tractor which exceeds the weight of the Implement by at least 20 DO NOT A WARNING tow the Implement behind a truck or other type of vehicle Never tow the Implement and another Implement connected in tandem Never tow the Implement at speeds over 20 MPH sri 06 Never allow children or other persons to ride on the Tractor or Implement A DANGER Falling off can result in serious injury or death sc 10 Make certain that the Slow Moving Vehicle SMV sign is installed in such a way as to be clearly visible and legible When transporting the A WARNING Equipment use the Tractor flashing warning lights and follow all local traffic regulations se s HT 10 Operation Section 4 23 2014 Ranch Rite OPERATION The SMV Slow Moving Vehicle emblem is universal symbol used to alert drivers of the presence of equipment traveling on roadways at a slow speed SMV signs are a triangular bright oran

operation

Contents

Download Pdf Manuals

Related Search

Related Contents