DVS 510
Contents
1. an action at the end of the countdown by setting the condition to Signal Status Inactive Driver has been optimized for volume Page 1 of 5 IP Link Device Interface extr_17_4883_3 pkn r Ethernet Communication Sheet Revision 1 29 2014 Control Commands amp States Audio Video Input 1 10 Output Resolution 640x480 60H2 800x600 60Hz 852x480 60Hz 1024x768 60Hz 1024x852 60Hz 1024x1024 60Hz 1280x768 60Hz 1280x800 60Hz 1280x1024 60Hz 1360x765 60Hz 1360x768 60Hz 1365x768 60Hz 1365x1024 60Hz 1366x768 60Hz 1400x1050 60Hz 1440x900 60Hz 1600x1200 60Hz 1680x1050 60Hz 1920x1200 60Hz 480p 60Hz 720p 60Hz 1080i 60Hz 1080p 60Hz 2048x1080 60Hz a 0 Timer 1 120 min Page 2 of 5 IP Link Device Interface Paste Revision 1 29 2014 Ethernet Communication Sheet extr_17_4883_3 pkn 1 Timer is in minute and is use to determine how long to wait when input signal is inactive before setting Input Status to inactive When the timer is set to 0 it is disabled If selection of timer doesn t have sec after the number then the number implies minutes 2 Consult user manual about use of these Input must have correct type settings and be active in order for recall to work Page 3 of 5 IP Link Device Interface r a Revision 1 29 2014 Ethernet Communication Sheet extr_17_4883_3 pkn Status Available Aspect Ratio Audio Video Input 1 10 Audio Inpu2. IP Link Device Interface extr_17_4883_3 pkn Revision 1 29 2014 Ethernet Communication Sheet This document provides additional assistance with wiring your Extron IP Link enabled product to your device Different components may require a different wiring scheme than those listed below For complete operating instructions refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation Device Specifications Device Type Scaler Manufacturer Extron Firmware Version 1 07 Model s DVS 510 Minimum Software and Firmware Requirements a Link ms Link GC Version Compiler Firmware 1 6 0 1 17 3 5 1 Version History Driver Version Date Notes Extron Certified version Tested on DVS 510 Added 60Hz a Maprani Output Resolution Functionality 2 8 31 2011 Extron Certified version Added Preset Save Preset Recall Aspect Ratio and Signal Status with Timer 1 3 9 2011 Initial Extron Certified version Driver Notes Timer and signal status are commands built into the driver to allow the user to trigger an action some number of minutes after there is no active signal connected to the switcher When the timer is set to 0 it is inactive When the timer is set to anything other than 0 the driver will begin counting down once there is no active signal connected Once the countdown is finished signal status will be set to inactive A monitor can be configured to trigger
3. t Audio Mute Connection Status Output Resolution PIP Input Signal Status Timer Status 640x480 60Hz 1024x768 60Hz 1280x768 60Hz 1360x765 60Hz 1365x1024 60Hz 1440x900 60Hz 1920x1200 60Hz 1080i 60Hz Active Status Unavailable 800x600 60Hz 1024x852 60Hz 1280x800 60Hz 1360x768 60Hz 1366x768 60Hz 1600x1200 60Hz 480p 60Hz 1080p 60Hz Inactive 852x480 60Hz 1024x1024 60Hz 1280x1024 60Hz 1365x768 60Hz 1400x1050 60Hz 1680x1050 60Hz 720p 60Hz 2048x1080 60Hz Count Down Video Input Video Mute Volume Discrete Page 4 of 5 extr_17_4883_3 pkn IP Link Device Interface Revision 1 29 2014 Ethernet Communication Sheet Network communication When configuring the Ethernet driver be sure device settings match that of the GC configuration Port Type Ethernet Logon Credentials Yes Supported Default Port 23 Multi Connection Yes Capable Port Changeable No Ethernet Driver Configuration Description Please refer to user manual for settings and changes to the network communication parameters Notes for the Device Page 5 of 5
Download Pdf Manuals
Related Search