Home

The Magnum Dolly System

1. www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech MovieTech Magnum Dolly Electronic Advanced Version Program Channel 3 The Pause at the end of a Recording Sequence The pause or break at the end of a recording sequence will not be recorded The recording of a sequence finishes upon reaching the end of the last movement and coming to a stop This has the effect that a sequence of for example 8 minutes and 30 seconds will not show on the Program Display as 8 5 minutes but instead as 6 5 minutes in the case of where the last 2 minutes were not a movement but a pause Should it be forgotten to end a sequence and the dolly it then switched off the sequence will not be recorded A recorded sequence remains memorized should the dolly be turned off or should another channel be selected www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 MovieTech Magnum Dolly Electronic Advanced Version Program Channel 3 Recalling of a Recorded Sequence To recall a sequence recorded on Channel 3 it is necessary to apply the same procedure as with Channel 1 see p 35 By pressing E the column will return to the reference or starting position During the movement the display will show GRF and upon reaching the position will show to indicate the reference posifion Important For technical reasons the same ramp that is selected during the recordin
2. MovieTech INSTRUCTION MANUAL Macnum DOLLY lt _ lt e ARRHEAD 2 Rey a Y I 1 iE Movie Tech ABC Products Movie Tech ABC Products Martin Kollar Str 9 Viale Edison 318 81829 M nchen 20099 Milano Germany Italia Tel 49 0 89 43 68 91 3 Tel 39 0 2 22470043 Fax 49 0 89 43 68 91 55 Fax 39 0 2 24410163 into movietech de k shore movietech de WWW MOVIETECH DE Macnum DOLLY T movieTech Contents Part I The Magnum Dolly System General Safety Tips Page 3 Movie Tech Magnum Dolly Technical Specifications Page 4 The Magnum Basic Dolly Page 5 Wheel Arm Positioning Page 7 Magnum Electromechanical Column Page 10 Battery operation Page 11 The Duo Jib Arm Page 14 Part Il The control of the Magnum Dolly Instruction Manual for control starting at page 18 www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech The Magnum Dolly Operation and set up instructions General Safety Tips 1 The Magnum Dolly should only be used on stable level surfaces at all times ad The entire lift range of the Magnums column jib arms ind Duo Jib max platform height 272 cm 8 9 ft etc must be kept clear and free from obstructions 0 5 m 19 7 in clearance in all directions whether switched on or off at all times When operating beware of pinch points Attention The Duo Jib Arm ma
3. Current position is set as top limit This position cannot longer be passed Both positions are cancelled The complete lift range of the column can be driven The memorized limits remain programmed even when the dolly has been switched off The limits are only set on Channel 0 upon switching to channel 1 2 3 the complete lift range may be driven Upon switching back to channel 0 the limits will be automatically reactivated The following 2 examples describe the programming input sequence and in turn the relative displays www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM 1an07 T Movierech MovieTech Magnum Dolly Electronic Advanced Version Program Channel 0 Reselecting the Column s lift range Example 1 It is required to set up a top limit of 500 mm Assuming that the column is at a current position of 276 mm In this case the displays will show the d following see diagram Firstly it is necessary manually drive the column using the manual control to the requested stop limit The new position here 500 mm will be z shown in the display see diagram y To register the current position as top limit it is necessary to simultaneously On the 2 digit Program Display for HIGH will be shown and turn the 3 digit Information Display will show 500 The set top limit of 500 mm can not be crossed The column now decelera
4. www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T movieTech Rotation around an off set axis fig 1 4 1 Extend all wheel arms fully 2 Extend all wheel arms fully 3 With the Wheel Setting Clamp pos 11 photo 1 set this combi wheel on FREE 4 The combi wheel on the opposite side diagonally should be set on FREE and then positioned at 90 to the wheel arm By selecting FIXED this combi wheel position will be secured This combi wheel may be used as the Steering point 5 The remaining two combi wheels should be set on FREE and positioned at 45 to each of their wheel arms These wheel positions may be locked by selecting FIXED Rotation around own central axis fig 1 3 1 Extend all wheel arms fully 2 With the Wheel Setting Clamp pos11 photo 1 put all wheels on FREE 3 Set all four combi wheels at 90 to each of their wheel arms 4 With the Wheel Locking Clamp set all wheels on FIXED Two wheel steering fig 1 2 1 With the Wheel Setting Clamp pos 11 photo 1 set all wheels on CRAB 2 Select two of the combi wheels that are parallel to each other and set them on FIXED 3 the steering rod in the Steering Rod Socket pos 2 photo 1 of either of the two wheels that are set on crab To return to 4 wheel steering set the Wheel Setting Clamp on each of the wheels at CRAB Turn the steering rod until all 4 wheels connect The Basic Dolly can be steered from each of the 4
5. Maximum Payload capacity ind 2 pers 250kg 251 165 www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 T Movierech Photo 3c Duo Jib Platform with High Low Range 10 Platform 11 Locking Lever and Bolt for Platform 12 Locking Lever and Bolt for High Low Rig 13 High Low Rig 14 Front section A On the upper connection of the front section pos 14 photo 3c mount High Low Rig pos 13 photo 3c as shown Insure that Locking Lever and Bolt pos 12 photo 3c is locked securely B Hand screw Bolt pos 1 Photo 3d into the hole pos 2 Photo 3d C Connect the Platform pos 10 photo 3c to High Low Rig as shown Insure that locking lever pos 11 photo 3c is locked securely D Ensure that all connections are locked and tightened correctly Maximum Payload capacity ind 2 per 200kg 440 Ibs Photo 3d High Low Rig 1 Bolt 2 Threaded hole When using the High Low Rig as High Rig it is necessary to hand screw the Bolt pos 1 Photo 3d into the Threaded Hole Pos 2 Photo 3d www movietech de the easy working film equipment t MovieTech MAGNUM DOLLY SYSTEM Jan07 MovieTech Magnum Dolly Control Advanced Version Operating Elements Page 19 Explanation Multi function Display Page 20 Operating Elements Hand Control Unit Page 21 Starting Page 21 Manual Operation Page 21 Drive Ramp Selection Page 22 Program Operation Page 23 Program
6. www movietech de the easy working film equipment MovieTech Movie Tech AG located in Munich is one of the leading manufactures of products and solutions for the film industry The product line of Movie Tech AG includes the hole range of camera cranes dollys light systems remote heads and related accessories Movie Tech AG purpose is to build professio nal film equipment to make the work for film teams on the set or in the studios easier In order to fulfill customer s requests better Movie Tech AG has branches in the U S and Italy Fate 7 a 1 a Movie Tech AG acquired the company ABCProducts in January 2000 with the objective to improve the development in the broadcast market ABC Products is today one of leading brands in the area of extremely light and high grade broadcast equip ment E J Since 2006 MTS equipment has been added to the portfolio of MovieTech AG MTS Media Technical Systems manufactures premium studio equip ment including droparms pantographs lighting hoists and telescopes Media Technical System MovieTech AG Martin Kollar Str 9 81829 M nchen Germany Tel 49 89 4368913 Fax 49 89 43689155 e mail info movietech de www movietech de MovieTech www movietech de M
7. Control down a5 1 The following stored movements can be activated in the same fashion press key A then press the Manual Control At the end of each programmed movement or stop release the Manual Control display stops blinking it is at this stage possible to manually drive the column in either direction via the Manual Control To commence a stored sequence it is necessary to first press GRF to go to the reference position The movement between any stored positions can at any time be stopped by releasing the Manual Control When the column reaches the first stored position in our example 370 mm it will stop automatically The blinking Information Display shows P1 If the Manual Control is released the Information Display stops blinking and shows a constant P1 The programmed movement is finished www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 Y movieTech Movie Tech Magnum Dolly Electronic Advanced Version Program Channel 3 Motion Control General With Channel 3 it is possible to memorize a complete movement including various speeds movement stops direction changes etc The movement can be recalled exactly as it has been programmed A complete movement can take up to 5 minutes or depending on the length of the stops up to 15 minutes It is possible to stop the sequence at any time The memorized sequence will not be cancelled by switching the dolly
8. Program Functions Key Functions in Switch on Phase Key Functions Channel 0 Keys STF or STM approx 2 secs Pressed only Channel 0 Setting of top or bottom limit Selection of battery or payload display Pressing of individual keys without function ED Shows Total Running Time Meter not adjustable ferr stv Setting bottom limit Shows Intermediate Running Time 5 on Meter Reset Meter with GRF enr t Setting top limit Ends Meter Display and starts normal enr Cancel both limits operation Both counters cannot be resetet Key Functions Channel 1 and 2 Each channel individually records a maximum of 30 positions On Channel 1 the positions and the fastest speed achieved since the last position may be On channel 2 only the positions may be programmed The movement between the positions remains manual Current position is recorded as reference start position Previously recorded program is cancelled Current position is recorded as of 30 possible positions per channel On channel 1 the fastest speed achieved between positions is also recorded Recalls column to reference start position Movement can be stopped by pressing Manual Control The speed of the movement depends on the selected speed range at time Starts movement to next position Channel 1 The maximum speed is recalled see STM and movement can be stopped by pressing Manual Control Channel 2 The speed is controlled manua
9. the activating position either upwards or downwards approximately 120mm The column is now fully operational www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 Photo 3 The DUO Jib Arm Components Duo Jib Arm 1 Connection Pin 8 Fixing Lock 2 Counterweight Rod 9 Anchor Bracket Column 3 Counterweight Triangle 10 Platform 4 End Section 11 Platform Locking Lever 5 Anchor Bracket Duo Jib 12 High Low Rig Locking Lever 6 Automatic Locking Pin 13 High Low 7 Connector Rod 14 Front Section t MovieTech 15 Platform Leveller 16 Middle Section 17 Connection Pin 18 Endsection Lock 19 Parallelogramm Rod www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM 1an07 Y movieTech Der DUO Jib Arm The Duo Jib Arm may only be used on the Magnum Dolly The following set up instructions should be observed Attention Before set up and at all times during operation ensure that either Drive Ramp 3 or 4 is selected Do not operate the Duo Jib on Drive Ramp 1 or 2 In the event of a power failure due to an electronical or battery cut out it is recommended to have an appropriate ladder to enable the camera crew to dismount Attention Do not use pneumatic wheels when mounting or operating the Duo Jib Extend all 4 wheel arms of the Basic Dolly fully pos 1 page 8 2 Mount the middle section pos 16 photo 3 of the Duo Jib onto the column by co
10. 00 mm Upon reaching the required position press STM The 3 positions have now been entered requested The display will show the following 300 mm Channel 1 3 movements entered column third memorized position i e P3 The entered positions will remain memorized even when the dolly has been switched off or when additional manual movements are made When manual movements are being made the Information Display will show the selected ramp here r 1 The number of entered movements will also be shown Our diagram depicts the display in the event of an manual movement in the event of a manual movement at 158 mm www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech Movie Tech Magnum Dolly Electronic Advanced Version Program Channels 1 and 2 To recall the memorized positions it is required to return to the starting position PO To do this press the key GRF During the drive to the starting position the display will show the following Present position 182 mm Channel 1 3 movements entered Dolly on drive Go to Reference When the column reaches the reference position in our example 200 mm it will brake gently It is now ready to repeat the respective movements The display will show the following Present position 200 mm Channel 1 3 movements entered dolly on starting position PO By pressing A for Action the column w
11. 1 Ramp 1 acceleration 100 Very hard acceleration and abrupt deceleration upon letting go the Manual control A gentle deceleration is only possible through the necessary operation of the Manual Control Not recommended for use with the Duo Jib 2 Ramp 2 acceleration 80 Somewhat softer acceleration and deceleration enabling smooth starting and stopping with 1 or 2 men on board camera crew even upon suddenly letting go of the Control For use with the Duo Jib it is required to manually select degree of smoothness of acceleration and deceleration 3 Ramp 3 acceleration 70 For operation with Duo Jib Acceleration and deceleration is somewhat softer than Ramp 2 4 Ramp 4 acceleration 60 Enables absolute smooth acceleration and deceleration for use with Duo Jib Even abrupt pressing and letting go of the the Manual Control results in soft starting and stopping The 4 ramping degrees also function in connection with the programming operation Furthermore the selected ramp also functions as said on the end switch areas ensuring the required acceleration and deceleration in these areas IMPORTANT BEFORE RESELECTING A RAMP SWITCH OFF DOLLY The reselection of a Ramp will only work when the dolly has been switched off Due to technical reasons the reselection will only be registrated upon activation of the dolly Therefore a reselection during operation will not be recognized www movietech de the easy working film e
12. Adapter Mount Die The Base Plate with Euro Adapter Mount pos 13 photo 1 as with all 3 fixtures is mounted on the Basic Dolly by simply positioning it on the dolly so that the 3 bayonet connections may be locked into position by the 3 Locking Screws pos 12 photo 1 Ensure that all 3 locking levers are tightened securely The Base Plate accommodates any accessory that connects to a Euro Adapter Mount www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 T Movierech Photo 2 Manual Electromechanical Column Components MAGNUM Column 1 Battery 2 Connection for Carry Bars 3 Battery Socket Flange 4 Programm Channel Selector 5 Drive Ramp Selector 6 Hand Control Unit www movietech de 6 7 Hand Control Cable 13 Foot Rest 8 Hand Control Cable Socket 14 Adjustable Seat Arm Bolt 9 Emergency Back up Switch 15 Turnstile Mount 10 Connecting for External Display 16 Turnstile Brake 11 Digital Display 12 Battery the easy working film equipment MAGNUM DOLLY SYSTEM 1an07 Y movieTech Magnum Electromechanical Column To operate the Magnum Column to its full potential it is important to understand the basic principles of how this column functions We have endeavoured to explain this in simple terms The Magnum s motor which is connected to a central spindle by means of a drive belt powers the column upwards or downwards Three pneumatic springs exerting an upward pressure p
13. Chanel 0 Page 23 1 Operation without program Page 23 2 Selecting the columns lift range Page 24 3 Payload Display for Duo Jib Page 29 4 Display for Operational Running Time Meter Page 30 Programming Chanel 1 and 2 Page 31 Change programming channel 2 Page 36 Programming channel 3 Page 38 End Switch Functions Page 43 Error Codes Page 45 Emergency Back up Page 45 Recap Programming Page 46 Fuse Plan Page 47 www movietech de the easy working film equipment Macnum DoLLy SYSTEM 1an07 7 movieTech MovieTech Magnum Dolly Electronic Advanced Version Order of Operating Elements Program Channel Selector Switch Channel 0 Lift range selection Payload Display Channel 1 Up to 30 set positions Channel 2 Up to 30 additional set positions Channel 2 Recording of a complete movement sequence including stops Connection for External Display PROGRAMM DISPLAY Emergency Back up Switch Only for use in the event of an electronic failure Connection for Ramp Selector Hand Control Unit 1 Standard operation 100 acceleration 2 Standard operation 80 acceleration 3 Duo Jib operation 1 70 acceleration 4 Duo Jib operation 2 60 acceleration www movietech de the easy working film equipment Macnum DoLLy SYSTEM 1an07 7 movieTech MovieTech Magnum Dolly Electronic Advanced Version Explanation Multi functional Display Position Display 3 digits Shows the actual column pos
14. Dolly with Mini Jibarm Maximum Payload Capacity 80 kg 176 Ibs Maximum Height euro adapter 235 cm 93 Minimum Height euro adapter 70 cm 27 Minimum Height with Mini Low Rig 9 cm 3 Lift range 165 cm 65 Magnum Dolly Low Rig Maximum Payload Capacity 130 kg 286 16 Maximum Height euro adapter 78 cm 30 Minimum Height euro adapter 10cm 4 Lift range 68 cm 26 the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 Photo 1 The Magnum Basic Dolly Components Basic Dolly 1 Steering Rod 2 Steering Rod Socket 3 Wheel Arm Lever 4 Carry Grip 5 Tension Adjuster www movietech de 6 Tension Adjuster 7 Looking Screw wheel axles 8 Studio Wheel 9 Track Wheel 10 Wheel Brake t MovieTech 11 Wheel Setting Clamp 12 Rotable Bearing 13 Euro Adapter Plate 14 Column Locking Screw 15 Rotatable Bearing Brake the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 Y movieTech The Magnum Basic Dolly The Basic Dolly photo 1 is the basis of the Magnum Dolly System It allows manouverability in a number of ways The wheel arms may be set in 16 different positions see Figure 1 Wheel Arm Positioning The wheel arms may be repositioned by pulling the Wheel Arm Lever pos 3 photo 1 Upon reaching the required position the Wheel Arm Lever should be gently released allowing the locking pin to slip into place Ensure that the wheel arm is fixed secure
15. age 21 The large 3 digit display shows the actual position of the column in mm here 276 mm The 1 digit Channel Display shows that Channel 0 has been selected The 2 digit Program Display shows There are no special functions activated The 3 digit Information Display bottom right shows r3 therefore the ramp 3 is activated The Linear Display shows the battery voltage 5 of the 8 digits are alight which means that the battery voltage is 23 V also see p 21 www movietech de the easy working film equipment Macnum DOLLY 1an07 1 movieTech MovieTech Magnum Dolly Electronic Advanced Version Program Channel 0 2 Selecting the Column s lift range Under certain circumstances when operating the Magnum Dolly it may be necessary to reduce the lift range of the column For example when operating the Duo Jib under a low ceiling or under a low hanging lighting set up The Magnum Dolly s programming facility caters for such circumstances as follows When Channel 0 is selected it is possible to dictate a new bottom and top end position via the programming keys in the hand control unit The column can therefore be driven only within this new lift range until otherwise instructed To memorize and to cancel the limits it is necessary to press 2 of the programming keys simultaneously always GRF another key Current position is set as bottom limit This position cannot longer be passed There are
16. dicates that the battery is fully charged Should the red LED alight this indicates that the battery is not fully charged At this point it should be explained that the Mains Charger Unit also acts as a battery charger As long as the column is not being driven the mains unit trickle charges the battery The charging cycle takes approximately 4 hours per battery The mains unit can also be used externally as a charger with the aid of a Charger Adapter Plate Note Newer models of the Mains Charger Unit are fitted with a manual switch over from lamp to 5 amp charge It is recommended to charge the batteries once a week on the 1 amp cycle Charging time is approx 8 hours per battery Once the power supply has been provided the following procedure should be followed 1 Ensure that the General Safety Tips have been followed 2 Connect the Hand Control Unit pos 6 photo 3 via the Hand Control Cable pos 7 photo 3 to the Control Cable Socket pos 8 photo 3 in the Electronic Unit Housing 3 Select the required drive ramp pos 6 photo 3 4 Activate the electronic by pressing the Main On Off Switch integrated in the Hand Control Unit 5 Press the Manual Control Switch in the desired direction i e forwards to go up press back to go down Note Upon activation should the column be in a fully retracted or extended position it is necessary to clear the two end switch areas This simply means that the column should be driven depending upon
17. elow 17 V for more than 2 seconds 5 H L The battery should be recharched as soon as possible This fault can occur when the motor due to a mechanical blockage is not able to provide the correct amount of revolutions as instructed by the electronic It can also 2 occur when due to a defective electromagnetic brake the column moves uncontrolled or the digital rotatable encoder is defective Emergency Back up Switch The Magnum Column contains an integrated emergency back up It can be found directly above the connection for the hand control cable in the electronic housing For easy access if is necessary to disconnect the hand control cable In the event of an electronical malfunction the column can be driven up or down by pressing the switch accordingly The emergency back up connects the motor directly with the battery and opens the electromagnetic brake for as long as the switch is pressed The result is a fast raw movement without any drive ramp control IMPORTANT THERE IS NO AUTOMATIC DECELERATION Should the column be driven completely to the end either at the or bottom and the switch is being pressed it is possible that motor damage will be caused It is therefore recommended that the emergency back up only be used when the electronic is not working www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM 1an07 T Movierech MovieTech Magnum Dolly Electronic Advanced Version Overall View of
18. en stored and the column has been driven to PO by pressing GRF The display will show the following Position 200 mm Channel 2 is selected 3 positions have been stored the column is at the reference position PO The speed between positions can be controlled exactly as To go to position 1 in our example 370 mm press key A for Action The blinking Information Display shows A There is not yet any column movement Movement is activated by pressing the Manual Control in the correct direction of the stored position 1 RIA blinking Display The speed between positions can be controlled exactly as with normal manual operation www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech Movie Tech Magnum Dolly Electronic Advanced Version Program Channel Depending on the location of the stored position the Manual Control must be pressed up or down The column will remain stationary if the Manual Control is pressed in the wrong direction It is not possible to change the direction of movement between two stored positions It is possible to stop and increase decrease the speed The Information Display indicates the correct possible movement direction imi Blinking Display Blinking Display Next stored position is higher upward movement Next stored position is lower downward movement possible press Manual Control up possible press Manual
19. et limits alternatively when the column is not in motion During upward movements the top limit will be shown and during will be shown and during downward movements the bottom limit will be shown To set a bottom limit the same sequence should be followed with the difference that instead of pressing GRF A it is necessary to press the combination GRF STM see page 28 www movietech de the easy working film equipment Macnum DOLLY 1an07 7 movieTech MovieTech Magnum Dolly Electronic Advanced Version Program Channel 0 Resetting of the full lift range To cancel the given set limits it is necessary to press the keys meg It is not possible to cancel only one limit The displays L and H will disappear upon cancel lation as well as the respective digits shown on the Information Display The column can now be driven through its complete lift range i e 0 to 683 mm The information Display will once again show the selected ramp this time 3 www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 Y movieTech Movie Tech Magnum Dolly Electronic Advanced Version Program Channel 0 Changing to other Channels It is possible to change program channels at any time without effecting the respective programs It is therefore possible to switch from Channel 0 to Channel 1 at any time should it be necessary for example to avail of the full lift range or to use d prog
20. f time it could result in the motor overheating However it is possible to measure the correct balance between load and counterload by gauging the required motor performance which can be indicated by the battery voltage drop during motion In case of correct balance the battery voltage drops by the same amount for both drive directions otherwise the motor must deliver more power for upward or downward motion respectively causing a higher battery voltage drop Therefore the battery voltage indicator can be used as a payload display Here is an example Display for Motor without load le el es Ee In case of correct balance the battery display shows the same voltage for both directions Upward Motion Downward Motion A 0 sl In case of one sided balance in one direction a higher motor performance is necessary Upward Motion Downward Motion es 050 0l In this case for a downward move a higher motor performance is required This means that the number of counterweights is too high www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 T Movierech Movie Tech Magnum Dolly Electronic Advanced Version Program Channel 0 4 Display for Operational and Running Time Meters The Magnum Dolly has 2 non resetable Time Meters Total Operational Time Meter from switch on to switch off 2 Total Running Time Meter actual movement of column The timing process will be
21. g phase must also be selected during the recall phase If this is not the case the column will not go to the reference position upon pressing GRF Instead the Information Display will indicate the ramp that was selected during the recording phase for as long as the GRF key is pressed Upon reaching the starting position press A to recall the recorded sequence During the recall the Programm Display will show PB indicating Playback The Information Display will count the length of the recorded sequence in our example 3 min 24 sec in reverse order enabling the operator to see how much time remains for the recorded sequence here 2 min 38 sec The recall can be interrupted as with Channels 1 and 2 at any time by pressing the Manual Control see p 36 Upon reaching the end of the repeated sequence the Information Display will show indicating finished The Programm Display indicates the length of the recorded movement 3 4 min By pressing the Manual Control the column returns to manual operation and the Information Display shows the selected ramp www movietech de t MovieTech Uu 3 Bs 62E Correct ramp Display shows GRF Dolly moves to reference position 3 BA ABIE Wrong ramp Display shows the ramp that was selected during recording phase g m 38 eum 43 8 3H LU the easy
22. ill drive automatically with the memorized speed to the first position in our example 370 mm During the movement the display will show the following Present position 325 mm Channel 1 3 movements entered dolly in Action A When the column reaches the memorized position in our example 370 mm it will stop automatically and P 1 will show on the display All memorized positions can be recalled in the same manner i e by pressing key A Upon reaching position 1 the display will show the following as per diagram The Magnum Dolly memorizes up to 30 positions in both Channels 1 and 2 www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech Movie Tech Magnum Dolly Electronic Advanced version Program Channels 1 and 2 In the same manner as described in our example the positions P2 and P3 as well as the memorized speeds can be recalled by pressing key A L At the end of the sequence the column will arrive at the position 600 mm position 3 Emergency Stopping Every programmed movement of the Magnum Dolly recalled by GRF or A can be immediately interrupted without having to switch the dolly off by pressing the Manual Control Pressing the Manual Control and therefore moving it out of its central position results in an abrupt immediate stopping of the column The column has now returned to manual operation The Info
23. interrupted in the event of an electronical error in order to prevent an unplanned resetting of the meter Meter 1 will generally show a higher amount of hours than meter 2 because the column is not always moving when switched on To gain access to the meters certain keys on the Hand Control Unit must be activated upon switching the dolly on approx 1 sec before switching on and approx 3 sec after switching on sr eng Meter 1 Meter 2 Total Operational Time Total Running Time Display Meter 1 Meter 2 Total Total T Operational Running Time T 3 Time reading Reading 1323 Hours 85 Hours The Channel Display shows 1 The Channel Display shows 2 for Meter 1 for Meter 2 f lt P r 4 r r1 C d gt 12 L 2 5 Press Key to return to normal operational Display www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 Y movieTech Movie Tech Magnum Dolly Electronic Advanced Version Program Channels 1 and 2 General Channels 1 and 2 provide the same programming facility as with previous models of the Magnum Dolly A certain amount of set positions up to 30 can be memorized and recalled in the same order as they were entered The speed between each position is the fastest speed achieved upon entering the individual positions The advanced version of the Magnum Dolly offers the
24. ition here 439 mm as well as the Error Display Code Channel Display 1 digit shows the selected Program Channel 0 3 here Channel 1 P Linear Display 8 digits shows battery voltage e g 8 digits on equals 26 V 7 digits on equals 25 V etc Here the battery voltage is 23 V By selecting Channel 0 it is possible to determine the payload situation on Duo Jib mode see Program Display 2 digits MEM shows information about the selected Additional information Program Channel Shown here for Display example 12 which means that 12 shows additional information positions have been memorized for example r3 Ramp 3 has been selected www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM t MovieTech MovieTech Magnum Dolly Electronic Advanced Version Starting By operating the ON OFF button see diagram the dolly may be turned on or off As soon as the lamp inside the ON OFF button lights up the button can be released After turn on a self test is performed by the electronic system for approx 1 second During this time the manual control must not be touched Otherwise the control erroneously recognizes an error and E04 is displayed see error messages In this case the ON lights flashes continuously until the dolly is turned off manually If the dolly is not turned off manually the hand control unit will execute an automatic tur
25. ition 276 mm Program Channel 1 0 movements in program Ramp 1 is selected Firstly the starting position for the first move must be reached i e 200 mm Upon reaching 200 mm press STF The display appears as in the accompanying diagram J The Information Display shows the starting position PO i e zero position The Program Display still shows 0 Display still shows 0 because a move g8 is defined as a start speed and end position at this stage of sequence only the start position has been entered www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech Movie Tech Magnum Dolly Electronic Advanced Version Program Channels 1 and 2 For the next step it is required to program the movement to the targeted position 370 mm at the required slow speed The column should be driven E d at the required speed to position 370 mm Now press STM The display will i show the following 370 mm Channel 1 1 movement entered column at first memorized position i e P1 Upon entering the first position the column now can be driven at the requested fast speed to the next position 600 mm Once again press STM upon reaching the requested position The display will show the following 600 mm Channel 1 2 movements entered column at second memorized position i e P2 At a medium speed now drive the column to the next position 3
26. l 3 Ending the Recording The diagram shows the display in the case of a running sequence time of 3 minutes and 24 seconds and at a stopped position of 173 mm which should 0 H d now be entered To enter press 829 The sequence is now ended The Information Display stops blinking and shows to indicate that the sequence has been L d recorded The Programm Display shows the length of the recorded sequence 11 i e 3 4 minutes Recording procedure the display will disappear and the Information Display will once again show the selected ramp r 1 to r 4 The length of the recorded sequence will remain in view on the Program Display Maximum Recording Time During the recording sequence data such as position direction etc will be memorized at a rate of 80 data per second That means that a sequence RES with more speed and direction changes requires more memory capacity than a sequence with more pauses and less speed and direction changes In practical terms this means that sequences with only short pauses have a capacity of approx 4 to 5 minutes and that the sequences with long pauses can carry on for 15 minutes or more Upon reaching the end of the memory capacity the Information Display will show OFL meaning overflow In this moment the sequence will be automatically recorded so ending the recording sequence This will have no effect on the manual operation
27. lay EOI Motriemperduretoohih 1 Mot E02 lnomedvologeinutl5Vatendstngg _ dE E03 Both end switches simultaneously activated B 1 E04 Column control button activated to soon uponswitchon Hde 1 E05 Incorrect signals from speed selector switch in hand control unit E06 Battery voltage below 17V DAE E07 Incorrect voltage on brake ER I E08 No voltage on brake brake possible not connected dEF E 09 Difference between supposed and actual position too high possible that 0l column is mechanically blocked or that drive movements are uncontrolled www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 Y movieTech MovieTech Magnum Dolly Electronic Advanced Version Error Messages The following errors can be caused by incorrect use An overheated motor can occur by driving the column too long with either too much or insufficient payload In this case switch the column off and let the motor cool down Upon activation the self diagnostic electronic goes through a system check fo ensure H a that no faults are present This takes approx 1 2 seconds During this time the manual i control should not be pressed If it is pressed and E04 occurs switch the column off and than restart This signal occurs when the battery voltage sinks b
28. lly Key Functions Channel 3 Motion Control Operation Recording and recalling of a complete sequence including various speeds direction changes and pauses Maximum drive movement 3 mins for movements with long pauses up to 15 mins Current position is recorded as reference start position Previously recorded program is cancelled Double Function 1 Starts recording of sequence once the reference position has been set 2 Ends the recording of sequence ferr Recalls column to reference start position Movement can be stopped by pressing Manual Control Drive speed depends on selected speed Starts the recorded sequence provided the column is at the reference start position Sequence can be stopped by pressing Manual Control Note Hand Control key functions only functional when column is not moving www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 T Movierech MovieTech Maanum Dolly Electronic Advanced Version Position plan of the fuses Lower Circuit Board Top View T Fuses 4 Amp mnie Blows only in case of defective electronic Main Fuse 25 Amps Can blow if the Dolly is driven against a mechanical obstacle during normal operation LIL Spare Fuse 25 Amps Fuse for emergency operation 25 Amps Can replace either the main or emergency fuse Can blow if the dolly during emergency operation is driven against an obstacle or a dead stop
29. ly Combi wheel Settings The Basic Dolly has 4 Combi wheels Each Combi wheel consists of 2 Studio wheels and 1 or 2 track wheels The Studio wheels can be exchanged for Pneumatic Wheels This is done by simply removing the Locking Screw pos 7 photo 1 and removing the studio wheel The pneumatic wheel is mounted in the same manner and locked in position with the Locking Screw Note With versions that have the single track wheel please note that 4 of the 8 pneumatic or studio wheels have a nipple type connection The other 4 wheels do not For each of the Combi wheels one wheel with nipple and one wheel without should be mounted The wheel with the nipple connection should be attached to the allocated connection The integrated Track Wheels allow smooth tracking movements without having to change the Combi wheels For operating on track the wheels should be set at the Free position to enable them to compensate the tracks curve Ensure that the track is supported correctly and completely level The Wheel Setting Clamp pos 11 photo 1 has 3 settings 1 CRAB gt Enables connected steering of the wheels 2 FREE gt Enables the wheels to rotate freely for use on track 3 FIXED gt Allows the wheels to be locked at set angles of 45 degrees Examples for possible wheel settings on the next page www movietech de the easy working film equipment Macnum DoLLy SYSTEM 1an07 1 Movierech Magnum Dolly Wheel settings
30. m will function with one battery or two When operating with one battery 24 volt ensure that the short circuit connector is connected to the battery connecting pins located on the column The digital display located on the Mains Charger Unit will indicate which system has been selected i e 24 or 48 V When operating with two batteries 48 volt energy will be consumed from both batteries simultaneously For longer operational time it is recommended to use two batteries It is also recommended to keep two fully charged batteries in reserve When the batteries reach 34 V an automatic shut down will take place The digital display on the electronic will show E06 The unloaded batteries should be replaced by a charged batteries This automatic shut down is meant to protect the batteries from being deeply unloaded i e below 17 V per battery www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 Y movieTech When operating with the Mains Charger Unit ensure that the batteries are charged Check that the mains unit is switched to the correct voltage i e 110 V or 220 V The voltage selector switch can be found on the rear side of the mains unit Newer models are equipped with an automatic volt selector Connect the mains cable to the mains unit and in turn to a mains power supply Switch on Upon switching the Mains Charger Unit on either the green or red LED will light Up Should the green LED alight this in
31. n off after 1 minute In the normal case of correct function the ON indicator will light continuously Manual Operation The drive speed of the column is controlled in both directions through the Manual Control With the assistance of the 4 speed selector buttons the following 4 speed areas can be selected V1 slow movement 20 V2 middle movement 35 V3 middle movement 60 V4 fast movement 100 With a battery voltage of 48 V and speed range and ramp 1 selected the coloumn s lift range of 683 mm can be covered in approx 3 1 sec ramp selection is discussed in detail on page 5 If the manual control has not been used for more than 30 minutes the control automatically turns off the dolly completely 60 seconds before turnoff the ON and the V lamps start to flash After turn off the selected speed range is stored To turn the dolly on again the ON OFF button must be pressed www movietech de HANDREGLER Speed Selectors Manual Control ON OFF Button Program Input the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech MovieTech Magnum Dolly Electronics Advanced Version Drive Ramp Selection With the Magnum Dolly it is possible to select 4 different degrees of acceleration and deceleration of a movement This enables one to select the necessary degree as per the individual requirements With the Ramp Selector 4 different degrees can be selected as follows
32. nel 3 selected length of memorized movement in minutes 00 means column at reference position A memorized sequence will be cancelled upon pressing str To commence the programming of a sequence it is necessary to press E The column is now in the state of record stand by To indicate this the Information Display showing starts to blink The recording of a sequence can now begin The recording is activated by pressing the Manual Control Should the recording not be activated within 10 seconds of pressing 9 the state of stand by will end and the display will stop blinking In the event of incorrectly activating record stand by pressing E once again will reverse the procedure In this case the display will also stop blinking By pressing the Manual Control the recording procedure will be activated and the display will show the following rc indicates that the sequence is being recorded The blinking Information Display indicates the length of the recorded sequence here 1 minute and 34 seconds The current position is 498 mm The sequence will be recorded exactly with all stops as well as with all changes in height direction speed etc co Ww n Ww CE 2 o Blinking Display www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech MovieTech Magnum Dolly Electronic Advanced Version Program Channe
33. nnecting it to the Euro Adapter Mount 3 Connect the Connector Rod pos 7 photo 3 to the Anchor Bracket on the column pos 9 photo 3 Insure that the Automatic Locking Pins are locked securely 4 Connect the Connector Rod pos 7 photo 3 to the Anchor Bracket of the Duo Jib of the Duo Jib pos 5 photo 3 Insure that the Automatic Locking Pins are locked securely 5 Lock the middle section securely with the fixing lock pos 8 photo 3 6 Mount the end section pos 4 photo 3 and tighten securely with the end section lock pos 18 photo 3 7 Attach the Counterweight Triangle pos 3 photo 3 to end section 8 Connect the parallelogram rod pos 19 photo 3 to middle section and counterweight triangle Insure that the connection pins pos 1 and 17 photo 3 connect correctly 9 On the lower connection of the front section pos 14 photo 3 mount High Low Rig pos 13 photo 3 Insure that locking lever pos 12 photo 3 is locked securely 10 Connect the Platform pos 10 photo 3 to High Low Rig Insure that locking lever pos 11 photo 3 is locked securely Maximum Payload capacity incl 2 pers 220kg 485 165 For other versions see the following pages 11 Insure that all connections are locked and tightened correctly No more than two counterweights should be loaded whilst the platform is unloaded As a general rule of thumb for one person on the platform attach 4 or 5 counterweights for two persons on
34. off Programming a sequence on Channel 3 does not influence in any way the memorized limits on Channel 0 or the sequences programmed on Channels 1 or 2 Each Channel functions completely independently of the other Manual operation on Channel 3 functions in exactly the same manner as with the other channels there are no special orders to observe The Hand Control keys provide the same functions as with previous models of the Magnum Dolly see Channels 1 and 2 Programming a Movement Taking for example that the column is tuned to Channel 3 and the current position is 174 mm There is no sequence memorized and ramp 3 has been selected The display will show the following The Position Display shows 174 mm The 1 digit Channel Display bottom left shows Channel 3 The 2 digit Program Display refers to Channel 3 3 is a andindicates that no sequence has been programmed i e 00 The Information Display shows that ramp 3 is selected i e r 3 Gem www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech Movie Tech Magnum Dolly Electronic Advanced Version Program Channel 3 The first step is exactly the same as with Channels 1 or 2 i e a reference or start position must be entered It is therefore necessary to manually drive the column to the required position In our example it is 75 mm Press STF the display will show the following Position 75 mm Chan
35. or transport Length Width Height Max Payload Capacity Maximum track width Minimum track width 62 kg 136 Ibs 64 cm 25 64 cm 25 37 m 14 5 1000 kg 2200 Ibs 62 cm 24 36 cm 14 Basic Dolly and Electromechanical Column Weight of Magnum Column Transport sitze assembled Length Width Height Maximum Payload Capacity Column extended Column retracted Max height euro adapter Min height euro adapter Lift range Fastest time through column lift range 24 V 48 V Sound level Battery performance when fully ranged Battery capacity Charge cycle with Mains Charger Unit 5A Mains voltage www movietech de 78 kg 171 15 64 cm 25 64 cm 25 80 cm 31 148 cm 58 300 kg 660 165 800 kg 1763 Ibs 148 cm 58 80 cm 31 68 cm 28 4 5 sec 3 2 sec 20 dB 150 column moves 8 Ah 8 hrs 3 hrs 110 220 V AC Magnum Dolly with Duo Jib Maximum Payload Capacity including 2 pers with High Rig mode photo 3c 200 kg 440 16 with Low Rig mode photo 3 220 kg 484 Ibs Standart mode photo amp 3b 250 kg 550 Ibs Max Platform Height 272 m 107 Min Platform Height 26 cm 10 Lift range 150 59 Magnum Dolly with Duo Jib and TV Platform Maximum Payload Capacity including 1 pers 192 kg 423 Ibs Maximum Platform Height 209 cm 82 Minimum Platform Height 59 cm 23 Lift range 150 59 Magnum
36. possibility to memorize 2 separate sequences One on Channel 1 the other on Channel 2 This results in the opportunity for example to program on Channel 1 5 positions and on Channel 2 10 completely different positions Alternatively it is possible to program on both channels the same positions but select different speeds Users who are familiar with the earlier versions of the Magnum Dolly and do not feel the need to familiarize themselves with the new system must simply select Channel 1 or Channel 2 and can therefore operate the dolly in the familiar manner they are used to For users who are not familiar with the programming facility here is a detailed explanation The Hand Control Unit is equipped with 4 programming keys The markings on the keys see diagram have the following meanings see p 33 www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM 1an07 T Movierech Movie Tech Magnum Dolly Electronic Advanced Version Program Channels 1 and 2 d ey Action Go to Reference STore reference Flag STore Movement Example It is requested to program the following sequences 1 slow paced move from position 200 mm to 370 mm 2 A fast paced move from position 370 mm to 600 mm 3 medium paced move from position 600 mm to 300 mm Consider for example that the column is at a position of 276 mm and there are no positions programmed The display will show the following Pos
37. quipment MAGNUM DOLLY SYSTEM Jano7 Y Movierech MovieTech Magnum Dolly Electronic Advanced Version Program Operation The advanced version of the Magnum Dolly offers a wide range of program possibilities which are provided as follows Channel 0 Resetting of the column drive range i e start and end position Channel 1 memorizing and recall of up to 30 positions as with older version Channel 2 Memorizing and recall of a further 30 positions Channel 3 Memorizing and recall of a complete movement sequence It is possible to reselect a Program Channel at any time by using the Program Channel Selector The individual possibilities are as follows Program Channel 0 Channel 0 offers the following possibilities 1 Operation without program input 2 Reselection of column drive range 3 Load display in Duo Jib operation 4 Display reading for Running Time Meter 1 Operation without program input In Channel 0 the operation of the individual program keys in the hand control have no effect All functions can only be activated by the simultaneous pressing of 2 program keys This has the effect that it is practically impossible to mistakenly activate the program procedure Therefore users who prefer to operate the Magnum Dolly manually must simply select the Program Channel 0 and need not concern themselves with further particular details regarding the programming possibilities In this case the display shows the following also see p
38. rammed sequence The set limits on Channel 0 remain memorized and upon switching back to Channel 0 will become immediately active Should the column be outside the at limit after returning to Channel 0 from Channel 1 2 or 3 it may only be driven in the direction which will return it to the set lift range area Upon entering the set lift range the set limits cannot be exceeded Examples Channel 0 has been programmed with a set lift range from 50 to 500 mm At some stage the user switches to Channel 1 2 or 3 and drives to a position of 600 mm From this position upon switching back to Channel 0 it will only be possible to move the column downwards until it reaches the set top limit of 500 mm Upon reaching the set top limit of 500 mm and entering the memorized set lift range the bottom and top limits will be activated www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 Y movieTech Movie Tech Magnum Dolly Electronic Advanced Version Program Channel 0 3 Payload Display for Duo Jib An important factor for efficient operation of the Magnum Dolly with the Duo Jib is the correct selection of counterweights Should too many or too few counterweights be used the result will be a reduction of speed in one of the respective directions and an overload on the drive motor and mechanics Under such circumstances the battery voltage will also drop at a faster rate Should the column be operated for a longer period o
39. rmation Display confirms this by showing the selected ramp here r 1 The entered movements remain programmed the Program Display shows 3 movements entered To return to the programmed sequence it is necessary to return to PO by pressing GRF www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T movieTech Movie Tech Magnum Dolly Electronic Advanced Version Program Channel 2 As of March 1995 the following changes have been made in the function and operation of Channel 2 As with the previous version it is still possible to store up to 30 positions The procedure to enter the positions with the keys STF and STM remains unchanged and corresponds with Channel 1 page 32 to 36 The recalling to the position PO by pressing key GRF remains unchanged The change made to Channel 2 is that it is now possible to manually control the speed of movement between each of the programmed positions as opposed to Channel 1 and the previous version of Channel 2 i e the speed of a movement between two positions is not registered when entering a sequence The individual positions may now be reached at any speed the dolly operator requires and in turn the entered set positions act as pre set stops The Magnum Column stops on the pre set position reliably and exactly For an example of the procedure please read the following If for example the same 3 positions as in our example on page 16 have be
40. rovide the extra strength necessary to carry a maximun payload of 300kg It is important to remember that the motor uses the least amount of energy when the column is loaded with approx 145kg This point should be taken into consideration when operating with battery power To achieve the longest consumption time with a battery always load the column The coordinating factor in the whole system is the Magnum Electronic The electronic provides the motor with the instructions needed to allow smooth coordinated movements of the column These instructions are in turn transmitted to the electronic from the operator via the Hand Control Unit When the Magnum Dolly is switched on the initial stage is stand by i e the electronic system is activated Within the first 1 2 seconds of activation the self diagnostic electronic makes an automatic system check to ensure that there are no faults present In stand by condition the column is held in position by an electromagnetic brake By pressing the manual control switch the electromagnetic brake is deactivated and the motor moves the column up or down When the column is no longer moving the motor regulates the position of the column for approximately 8 seconds After 8 seconds the brake closes again and holds the column in position During the time the motor is moving or regulating the columns position energy consumption is at its highest Upon activation of the electromagnetic brake energy consumption drops drama
41. tes smoothly at 500 mm The display continues to show H 500 regardless of the current column position here 75 mm constantly informing one of the top limit To set a bottom limit the same sequence should be followed with the difference that instead of pressing GRF A it is necessary fo press the combination GRF STM see example 2 www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jan07 T Movierech MovieTech Magnum Dolly Electronic Advanced Version Program Channel 0 Reselecting the column s lift range Example 1 It is required to set a new lift range between 45 and 520 mm Assuming that the column is at a position of 276 mm and the top limit has been set at 520 mm as per example 1 The displays will show the following see diagram Firstly it is necessary to manually drive the column using the manual control to the requested bottom limit The new position here 45 mm will be shown on the display see diagram To register the current position as top limit it is necessary to simultaneously press 0 B On the 2 digit Program Display H for HIGH will be shown and on turn the 3 digit Information Display will show 500 The set lift range limit between 45 mm and 520 mm cannot be crossed The column now decelerates smoothly at the set limits The display continues to show LH as a reminder that limits have been set The Information Display will show the s
42. the platform attach 8 or 10 counterweights When operating the Duo Jib attention must be payed when mounting and dismounting the platform By two man operation remove the extra counterweights before one person dismounts i e no more than four or five counterweights should be left connected Before the second person dismounts reduce the amount of counterweights to three It is not recommended to drive the Duo Jib when the platform is unloaded and counterweights are attached At all times attention must be payed to balance www movietech de the easy working film equipment Macnum DoLLy SYSTEM 1an07 T Movierech Photo 3a Duo Jib Platform 10 10 Platform 11 Locking Lever and Bolt for Platform 14 Front section A Connect the Platform pos 10 photo 3a to the upper connection on the Front Section pos 14 photo 3a as shown Insure that the Locking Lever and Bolt pos 11 photo 4a are tightened correctly B Insure that all connections are locked and tightened correctly Maximum Payload capacity inc 2 per 250kg 551 lbs Photo 3b DUO Jib Platform 10 Platform 11 Locking Lever and Bolt for Platform 14 Front section A Connect the Platform Pos 10 Photo 3b to the lower connection on the Front Section Pos 14 Photo 3b as shown Insure that the Locking Lever and Bolt Pos 11 Photo 3b are tightened and locked securely B Insure that all connections are locked and tightened correctly
43. tically to an absolute minimum Getting Started 24 Volt Version Power supply The Magnum Column operates on 24 volt battery power or can be mains buffered at 110 V to 220 V by means of the Mains Charger Unit Note Always use the Mains Charger Unit together with a fully loaded battery Do not use Mains Charger Unit on its own as this will damage the electronic Battery operation One or two batteries can be connected to the column by means of the socket flanges pos 3 photo 3 The Magnum will function with one battery or two When operating with two batteries energy will be consumed from both batteries simultaneously For longer operational time it is recommended to use two batteries It is also recommended to keep one fully charged battery in reserve When the battery reaches 17 V an automatic shut down will take place The digital display on the electronic will show E06 The unloaded battery should be replaced by a charged battery This automatic shut down is meant to protect the batteries from being deeply unloaded i e below 17 V www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM 1an07 Y movieTech When operating with the Mains Charger Unit one battery must be removed and the mains unit connected in its place Ensure that the battery is charged Check that the mains unit is switched to the correct voltage i e 110 V or 220 V The voltage selector switch can be found on the rear side of the mains
44. unit Newer models are equipped with an automatic volt selector Connect the mains cable to the mains unit and in turn to a mains power supply Switch on Upon switching the Mains Charger Unit on either the green or red LED will light up Should the green LED alight this indicates that the battery is fully charged Should the red LED alight this indicates that the battery is not fully charged At this point it should be explained that the Mains Charger Unit also acts as a battery charger As long as the column is not being driven the mains unit trickle charges the battery The charging cycle takes approximately 4 hours The mains unit can also be used externally as a charger with the aid of a Charger Adapter Plate Note Newer models of the Mains Charger Unit are fitted with a manual switch over from lamp to 5 amp charge It is recommended to charge the batteries once a week on the 1 amp cycle Charging time is approx 8 hours Getting Started 48 Volt Version Power supply The Magnum Column 48 volt system operates on 24 or 48 volt battery power i e 1 or 2 batteries or it can be mains buffered at 110 V to 220 V by means of the Mains Charger Unit Note Always use the Mains Charger Unit together with fully loaded batteries Do not use Mains Charger Unit on its own as this will damage the electronic Battery operation One or two batteries can be connected to the column by means of the socket flanges pos 3 photo 3 The Magnu
45. wheel arms provided the designated wheel arm is switched to Crab Should the Combi wheels of the Basic Dolly need adjustment because they are not running straight e g due to a bump or knock the following action needs to be taken Older models Ensure that the Locking Clamps of all the combi wheels are set at Lock 2 Open the Locking Bolt above the Combi wheel with an Allen Key 3 With the help of a wheel locking bar water level or any straight object align the wheels so that each set of two wheels are parallel fo each other 4 Re lock the Locking Bolt Newer Models Ensure that the Locking Clamps of all the combi wheels are set at Lock 2 Directly above the track wheel there are 2 locking bolts Loosen the locking bolts 3 With the help of a wheel locking bar water level or any straight object align the wheels so that each set of two wheels are parallel to each other 4 Re lock the Locking Bolt www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech The Basic Dolly contains a Rotatable Bearing pos 12 photo 1 which allows complete panning of columns etc mounted on it The rotatable bearing may be locked with the Rotatable Bearing Brake pos 15 photo 1 Maximum payload on the Basic Dolly is 1000 kg The Basic Dolly accommodates 3 different fixtures 1 Base Plate with Euro Adapter Mount 2 Manual Cranked Column 3 The Magnum Electromechanical Column Base Plate with Euro
46. witching on in low positions Channel 3 selected Movement with 4 2 minutes memorized Position within the bottom end switch area therefore program keys non functional and only upward manual operation possible As soon as the respective end switch is cleared the column can be moved in both directions and the programming is once again functional The Information Display will show the selected ramp and the display H or L will disappear www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM Jano7 T Movierech MovieTech Magnum Dolly Electronic Advanced Version Error Display If during operation a fault occurs the column will stop and the 3 digit Position Display will show an error code The numbers of the Channel and Programm Display will disappear and the Information Display will assist in referring to the possible source of the fault The Position Display will show the letter E for Error plus one of the additional numbers 01 to 13 The Information Display assists the search for the error by showing 3 letters describing the possible fault In the following example the dolly is out of order because battery voltage has dropped below 17 V The Position Display shows bAt as an indication that the battery is the error source Information Display Report ES Hide dEF Tom EY End Switch aet OO Error Code Error Source Information Disp
47. working film equipment MAGNUM DOLLY SYSTEM Jano7 Y movieTech MovieTech Magnum Dolly Electronic Advanced Version Function of the end switches The Magnum Dolly is equipped with 2 end switches which can be found in the column approximately 10 cms from the top and the bottom respectively Should the column find itself within the vicinity of either of these end switches upon switching on the dolly it is only possible to drive the column in the direction that will enable it to clear the respective switch i e in the bottom end switch area upwards in the top end switch area downwards Therefore the dolly cannot be driven against the mechanical stops in case the position stored by the electronic is not the same as the actual position e g if the emergency back up switch has been used before On Channels 1 2 3 access to the recorded programs is only possible upon clearing the end switches However in Channel 0 the recorded limits are immediately accessible Upon switching the dolly on and the column is in one of the end switch areas and there is a recorded sequence on the selected channel the Information Display will indicate respectively H for high and L for low Example 1 Upon switching low position Channel 1 selected 3 set positions memorized Position within the top end switch area therefore program keys non functional and only downward manual operation possible Example 2 Upon s
48. y not be mounted or operated when the Magnum Dolly is fitted with pneumatic wheels 3 4 Attention in automobiles or uneven surfaces The Magnum Dolly must be secured so that it cannot move or roll 4 In the electromechanical column there are 3 pneumatic springs which are under constant high pressure Should the column be damaged or the mechanics interfered with it may eject with high speed and strength The drive belt must be inspected and if necessary replaced after every 100 operational hours or at least every 12 months The load carrying device must be inspected after every 100 operational hours To inspect or repair the column the column must be extended fully to relax the pneumatic springs 5 4 Absolute attention to balance must be observed at all times especially during set up and operation 0 When operating the Duo Jib in open air the maximum operational wind speed of 32 km h 19 mph may not be exceeded When operating from mains all usual guidelines for operating electrical equipment must be observed All electronical components should be protected from over exposure to moisture and humidity 9 It is recommended to use safety belts when operating at heights above 1 50 m 5 ft www movietech de the easy working film equipment MAGNUM DOLLY SYSTEM JANO7 t MovieTech Technical Specifications Magnum Dolly System Basic Dolly Weight Minimum size f

The Magnum Dolly System

Contents

Download Pdf Manuals

Related Search

Related Contents