Home

WWW.SCOTT-SPORTS.COM

1. 2016 BIKE USER MANUAL GENIUS ENGLISH 19 9 F ADJUSTABLE BB HEIGHT On Genius bikes equipped with the FOX Nude or the FOX CTD shock you can adjust the BB height above ground in 2 positions by flipping a geometry chip located on the linkage bar shock mount 1 low BB for lower center of gravity over ground 2 high BB for bigger clearance between pedals crankset and obstacles on the ground IMPORTANT It is not possible to use this geometry chip with other shock models than the FOX Nude or FOX CTD The shock might collide with parts of the frame or linkage bar 6 20 ENGLISH GENIUS 2016 BIKE USER MANUAL P FRONT DERAILLEUR FD MOUNTING DETAILS On all Genius frames you will find a Shimano E type front derailleur but fixed directly on the swingarm without the plate that is fixed normally between the bottom bracket bearing cup and the bottom bracket housing of the front triangle or a SRAM Direct Mount Type S3 FD Please note that you always need to use the adapter plate attached to the bike or frame set between chainstay and front derailleur This adapter can be ordered at the SCOTT distribution with parts number 229728 FD Mount Genius 2013 700 650B 229729 FD Mount Genius 2013 900 29 also to be used for the Genius 700 Plus Please note that the 2 sizes of the adapters are not interchangeable 2016 BIKE USER MANUAL GENIUS ENGLISH 21159 Y CHAINGUIDE Details for the assembly on the alloy frames of Gen
2. When you reached the needed pressure remove the pump and put the valve cap on the valve 2016 BIKE USER MANUAL GENIUS ENGLISH 15 56 Y SAG Please refer to the following instruction Ride your bike off a pavement remain in the saddle and check how many times it bounces The SAG should be 14mm 700 respectively 12 5mm 900 700 Plus on the shock piston lf it bounces 1 2 times the set up is good To check the adjustment please follow as shown below lf it bounces more than 3 times the rebound is too fast Turn the knob 1 2 clicks 1 sit on the bike put your feet on the pedal clockwise 2 put your feet back on the ground and stand over the bike without bouncing the bike If it does not bounce the rebound is too slow Turn the knob 1 2 clicks counter during this action clockwise 3 check if the o ring S9 on the shock piston S8 has a distance of 14 12 5mm to the main IMPORTANT USM O AO Note that you have to mount the FOX Nude Shock always as shown below if the distance between the o ring and the main dust wiper seal is 14 12 5mm the air pressure is matching to your weight Mounting the rear shock in a different position can cause severe damage to the frame the linkage levers and the rear shock if the distance between the o ring and the main dust wiper seal is less than 14 12 5mm the air pressure of the air chamber is too high and should be carefully reduced by using the bleed knob of the shock pu
3. with 11 8 straight M STACK 613 0mm 241in 610 0mm 24 0in 6140mm 242in 6ILOmm 241in 6230mm 245in 620 0mm 244in 633 0mm 249in 630 0mm 248in 44 0mm N STEMLENGTH 40 0mm 16in 400mm 16in 500mm 20in 50 0mm 20in 600mm 24in 60 0mm 24in 700mm 28in 70 0mm 28in Fork travel 900 130mm 700 Plus 140mm Fork length 900 540mm 700 Plus 545mm BB housing BB PF 92 Front derailleur 900 Shimano E Type SRAM S3 direct mount Bearings Max Tire Width 700 Plus E type with 3mm outboard 2 x IGUS 6 x 6802 24 x 15 x 5 900 57mm 2 25 700 Plus 75mm 3 0 Y TC SHOCK TECHNOLOGY TWINLOC LEVERS The heart of the TC System is the FOX Nude Shock made by FOX offering three functions which make this system possible GENIUS 900 S S M H AL AL LOW BB SETTING HIGHBB SETTING LOW BB SETTING HIGHBB SETTING LOWBBSETTING HIGHBB SETTING LOW BB SETTING HIGH BB SETTING The TWINLOC XL remote control lever is the evolution of the already outstanding TRACLOC A ie 68 9 69 4 68 9 69 4 69 0 69 4 69 0 69 4 system of SCOTT B aa 100 0mm 39in 100 0mm 39in 1000mm 39in 1000mm 39in 100mm 43in 00mm 43in 120 0mm 47in 1200mm 47in While TRACLOC allowed only the change on the SCOTT TC rear shocks between the C eee aL 570 3mm 225in 569 0mm 22 4in 600 3mm 23 6in
4. 300 psi with a special air valve connector preventing from air getting away while removing the pump from the shock valve this will result in an exact air pressure Please note that air will flow into the hose and indicator when counterchecking the air pressure so you have to set up again the recommended pressure after this action Make sure to balance at least this air loss when you make a check of the air pressure of the shock Please also note that the indicators of shock pumps have a tolerance of max 10 5 14 ENGLISI GENIUS 2016 BIKE USER MANUAL PF SET UP GENIUS WITH FOX NUDE OR FOX CTD SHOCK The Set Up of the FOX Nude or FOX CTD Shock can be easy done within a few minutes IMPORTANT For all adjustments of the air soring the remote lever has to be in position all travel To adjust the air pressure of the air chamber of the FOX Nude or FOX CTD Shock please refer to the following instruction 1 Remove the valve cap of the valve s5 located on the shock housing S3 2 Mount the shock pump with its adaptor on the valve 3 Please take into account that it takes some air pressure from inside the shock to drive the indicator on the pump Make sure to balance at least this air loss when you make a check of the air pressure of the shock Pls also note that the indicators of shock pumps have a tolerance of max 10 4 Please use the FOX iRD App available at the Tunes App store with following link httos itunes apple co
5. 598 9mm 23 6in 6252mm 24 6in 6238mm 246in 650 2mm 25 6in 648 8mm 25 5 in SCOTT patented Lock out traction and full mode on the fly from the handlebar the SNOWED aS es TWINLOC allows also the remote control of the front fork to shift between lock out and D IFIGH 770 4mm 30 3in 772 8mm 30 4in 7728mm 30 4in 775 5mm 30 5in 803 0mm 316in 8061mm 31 7in 800 6mm 315in 8038mm 31 6 in a ee L a open mode at the same time when you change the modes on the SCOTT rear shox E BBOFFSET 345mm 1 4in 291mm lin 34 5mm 14in 290mm llin 340mm 13in 28 5mm llin 340mm 1 3in 28 4mm llin F BBHEIGH 335 5mm 13 2in 340 9mm 13 4in 335 5mm 13 2in 34 0mm 134in 336 0mm 13 2in 34 5mm 134in 336 0mm 13 2in 34 6mm 13 4 in In combination with FOX 34 CTD or FOX 32 CTD forks it is also possible to have a platform G WH BAS 112 2 mm 43 8in 1118mm 43 8in 1142 2 mm 45 0 in 1141 8mm 45 0 in 1168 0 mm 46 0in 11676 mm 46 0 in 11939mm 470 in 1193 5mm 47 0 in mode on the fork BBC R H TO TOPTUBE RAS The 3 modes of CTCD in combination with FOX Nude are BBC R TOTOROF 415 0 mm 163in 45 0mm 16 3in 440 0mm 173in 440 0mm 173in 475 0mm 18 7in 475 0mm 18 7in 510 0mm 201in 510 0mm 20lin Climb Mode lock out rear lock out front SEATTUB J SEATANGLE CPOS o E en coe C O Traction Mode traction mode rear incl Geometry change and reduced travel platform K CHAINSTAY 450 0mm 177in 449Omm 177in 450 0mm 17 7in 4490mm 17 7in 4499mm 177in 448 9mm 17 7in 4499mm 17
6. 7in 4489mm 177 in mode front L REACH 94 2mm 15 5in 3992mm 15 7in 4242mm 16 7in 4291mm 169in 4471mm 176in 451 8mm 178in 469 4mm 18 5in 4741mm 18 7 in M STACK 770 4mm 30 3in 7728mm 30 4in 7728mm 30 4in 775 5mm 30 5in 803 0mm 3l 6in 8061mm 317in 800 6mm 315in 803 8mm 31 6in Descent Mode full travel rear Descent full travel front N STEMLENGTH SON OOO NAZI 70 0 mm 2 8in 70 0mm 28in SOON IIS OO 90 0 mm 5in 90 0mm 3 5in The 3 modes of CTD in combination with the FOX CTD shock are Climb Mode lock out rear lock out front Ride Mode platform Ride mode rear platform mode front Descent Mode full travel rear Descent full travel front 6 06 GENIUS GENIUS 07 9 Therefore SCOTT offers 2 different TWINLOC levers with following fork rear shock combinations FOX Nude with different rolls for FOX CTD fork and RockShox DNA 3 fork SCOTT Article number 230097 FOX CTD with different rolls for FOX CTD fork and RockShox DNA 3 fork SCOTT Article number 230098 Please note that the FOX CTD rear shock does not offer a traction mode but a platform mode In contrary to FOX Nude the air chamber volume of the positive chamber remains the same throughout the different modes IMPORTANT You can only assemble the TWINLOC remote lever in left side upward position on the handlebar You have 3 positions of the TWINLOC remote lever CLIMB MODE the shock is locked climbing on asphalt roads is now possible without any power loss S
7. 9in NOOmm 43in NO 0mm 43in 1200mm 47in 1200mm 4 7in 2 60 E Ratio C ONE 570 0mm 224in 570 0mm 224in 600 0mm 236in 600 0mm 23 6 in 625 0mm 246in 6250mm 246in 650 0mm 25 6in 650 0 mm 25 6 in Piston stroke 50mm D aoe aa 8190mm 32 2in 8220mm 324in 8230mm 324in 826 0mm 32 5in 843 0mm 33 2in 846 0mm 33 3in 8650mm 34lin 868 0mm 34 2 in Shock length 190mm E BBOFFSET 30 0mm 1 2in 250mm 1 0in 30 0mm 1 2in 250mm 10in 30 0mm 12in 250mm 10in 30 0mm 12in 250mm LOin Eye to Eye F BB HEIGH 220 132in 3400mm 13410 335 0mm 13 2in 3400mm 134in B3B0mm 132 3400mm 13418 3350 mm 132in 340 0mm 134in G WH BAS 1135 0 mm 44 7 in 11340 mm 44 6 in 1165 0mm 45 9 in 1164 0 mm 45 8in 119 0 mm 46 9 in 1190 0 mm 46 9 in 1271 0mm 50 0 in 1270 0 mm 50 0 in Ja 22 2mm x 8mm BBC R Mainframe H O TOPTUBE 36 0mm 13 2in 336 0mm 13 2in 3450mm 13 6in 345 0mm 13 6in 378 0mm 149in 378 0mm 149in 4090mm 161in 409Omm 16 1in Hardware CENTER 22 2MM x comm BBC R Swingarm TO TOP OF 45 0mm 16 3in 450mm 163in 440 0mm 173in 440 0mm 173in 4750mm 187in 4750mm 187in 510 0mm 20lin 510 0mm 20lin SEATTUB hoe 31 6MM J SEAT ANGLE 73 9 74 40 79 74 42 73 90 74 4 739 74 4 SS K CHAINSTAY 445 0mm 175in 4450mm 175in 4450mm 175in 445 0mm 175in 4450mm 175in 4450mm 175in 4450mm 175in 445 0mm 175 in semi integr for tapered 11 8 1 5 44 54 9mm L REACH 395 0 mm 15 6in 399 0 mm 15 7in 4250mm 167in 4290mm 16 9in 4480mm 176in 4520mm 178in 470 0mm 18 5in 4740mm 187in Headset Inner diameter of frame or
8. All rights reserved 2015 SCOTT Sports SA Distribution SSG Europe v5 1 03082015 Distribution Center SA P E D Zone Cl Rue du Kiell 60 6790 Aubange Belgium WWW SCOTT SPORTS COM SCOTT Sports SA Route du Crochet 17 CH 1762 Givisiez Phone 41 26 460 16 16 Fax 41 26 460 16 OO Email oostmaster scott sports com SL aI T DKE SCOTT GENIUS USER MANUAL 2016 INNOVATION TECANOLOGTY DO Eo G IN WWW SCOTT SPORTS COM Y CONTENTS Genius Concept aa a 00 04 Geometry Technical Data Genius 700 O5 Geometry Technical Data Genius 900 700 Plus 06 WWW SCOTT SPORTS COM TC Shock Technology Twinloc Levers 07 Assembly of the Remote Cable 10 FOX Nude Shock and Twinloc Remote Control Lever 11 ee dde Sd de ee do Basic Set Up of the Twinloc Remote Control of FOX Nude Shock 12 E ee UO ale ani Basic Set Up of the Twinloc Remote Control of Fox CTD Shock 14 All adjustments should be done at your local SCOTT dealer or following this manual s instructions Recommended Tools for the Shock Set Up 14 In order to avoid technical problems or any harm please contact Set Up Genius With FOX Nude Or FOX CTD Shock 15 in case of doubts your authorized SCOTT dealer SAG eae eee ew eee abbeeeee eee deee nese se ees bbe 16 Set Up of Rebound F
9. OX Nude Or FOX CTD Shock 16 Set Up of Other Shock Models 18 Headset Options 000000 2 18 Bottom Bracket BB on Genius 19 Adjustable BB Height 20 Front Derailleur FD Mounting Details 21 Chainguide e ro sc sa sesa BREESE eee asar 22 Genius Cable Routing 23 Adjustment of Seatpost Height 27 Replaceable Dropout 28 Rear Disc Brake Mount 28 Front Fork Set Up Change of Front Fork 29 Pivot Maintenance 2 a 29 Warranty 2 4444444444 ee ee ee 30 G 02 GENIUS GENIUS 03 9 P GENIUS CONCEPT F GEOMETRY TECHNICAL DATA GENIUS 700 The new Genius is the result of 2 years of research and development for one of the lightest Travel 150 100 0mm trail marathon bike frame set available on the market hitting the scale at below 23009 5lbs Suspension including the frame FOX Nude CTD shock and the unique TWINLOC remote control Ratio a SCOTT s focus was not only on lightweight but also on a durable and stiff frame with an Piston stroke ss innovative suspension technology in combination with an optimized kinematics of the rear Shock length Done swingarm Eye to Eye ae a Hardware The combination of an optimized kinematics with an extraordinary suspe
10. WS 135 12 parts set In case of a change of the bearings or of the rear swingarm you should contact your local HOSTS ich ade iesaceasle AD ases SCOTT dealer as you need special tools for disassembly and assembly F REAR DISC BRAKE MOUNT Genius can be used with 2 different disc rotor sizes on the rear brake The rear disc brake on Genius is Postmount PM Standard on the left seatstay and it is possible to use disc rotors with 180 and 185mm diameter Please note that for the assembly of 185mm rotor you might need adapters washers between the PM port on the frame and the brake calliper 6 28 ENGLISH GENIUS 2016 BIKE USER MANUAL 2016 BIKE USER MANUAL GENIUS ENGLISH 29 9 Y WARRANTY Frame INE e sta ee ee ee en om ASA ee Beii lo dades o A II EEEE KEE TERRAE 6 30 ENGLISI GENIUS 2016 BIKE USER MANUAL Y WARRANTY SCOTT bikes are made using the most innovative production and quality methods They are equipped with best components of well known parts suppliers Doing so SCOTT warrants its frames and swingarms for five years subject to compliance with maintenance ranges see below and SCOTT forks provided it is a fork of SCOTT for two years for defects in material and or workmanship in case of purchase of completely assembled bikes This warranty of 5 years for the frames shall only be granted in case once a year a maintenance service has been effected according to maintenance requirements as set forth in this manual b
11. ages on the shift cables and brake hose In addition to the derailleur cables and the brake hose you also will see a possibility for an integrated cable routing of the seatpost remote on the carbon version of Genius For the rear brake please assemble the cable as shown in the following drawings In order to seal the housing ports on the frame you should use the plugs attached to the bike ALLOY FRONT FRAMES Please fix the derailleur cable housings the brake hose and the remote seatpost cable housing Cif applicable on the frame on the cable mounts with the mount clips by Please tighten the mount bolt with a following the routing info as shown max of 4Nm F ADJUSTMENT OF SEATPOST HEIGHT IMPORTANT The seatpost has to be inserted into the seattube at a minimum of 1OOmm Never use another seatpost diameter than 31 6mm or try to use a shim reducer between seatpost and frame 229724 Cable Clamping Set Genius alloy 2013 one size 6 26 ENGLISH GENIUS 2016 BIKE USER MANUAL 2016 BIKE USER MANUAL GENIUS ENGLISH 27 9 Y REPLACEABLE DROPOUT For 185mm rotor diameter you will need 2 red anodized spacers that can be ordered via the SCOTT distribution with On Genius bikes of model year 2013 you can replace the rear derailleur hanger Depending 219568 Brake Mount Adapt Spacers 4mm f 185mm on the different models you ll find following options 1 142mm axle with RWS 142 12 This is available via the SCOTT distribut
12. ay In addition the SAG is reduced and the geometry gets steeper E z A i 4 en Some models of Genius use also the FOX CTD shock which offers instead of the Traction Mode a Platform Ride Mode in between Climb Mode and Descent Mode No power will be lost and an optimum power transfer is guaranteed as the swingarm in contrary to locked or automatic locking systems can follow the trail surface and will offer LOW BB SETTING SS 100 0 mm 3 9 in 569 9 mm 22 4 in HIGH BB SETTING 68 4 100 0 mm 3 9 in 568 6mm 22 4 in 599 9 mm 23 6in 598 6mm 23 6 in LOW BB SETTING HIGH BB SETTING 68 4 10 0mm 43in N0 0mm 4 3 in LOW BB SETTING HIGH BB SETTING LOW BB SETTING HIGH BB SETTING 579 68 4 679 68 4 120 0mm 4 7in 1200mm 4 7in 1350mm 5 3in 1350mm 5 3in 624 9 mm 24 6 in 6236mm 246in 6499mm 25 6in 648 6 mm 25 5 in perfect traction and higher speed while standing on the pedals D 7731mm 30 4in 775 9mm 305in 7746mm 30 5in 7776mm 30 6in 807 0 mm 318in 810 4mm 319in 809 0mm 31 9in 812 4 mm 32 0 in E 1 6mm O0 5in 61mm 0 2 in 0 5in 61mm 0 2in 1 6mm O5in 6lmm O 2in 1 6mm O 5in 6 1mm 0 2 in F 3449mm 136in 350 4mm 13 8 in 13 6in 350 4mm 13 8in 3449mm 13 6in 350 4mm 138in 3449mm 136in 350 4m
13. ecure it with a cable end cap Please refer for this action also to the manual of SRAM RockShox or FOX attached to the bike 2mm allen TIP To check for accurate cable tension please try to move the plastic end cap of the cable housing at the barrel adjuster on the remote lever There should be no play between cap and barrel adjuster In case of play please turn the barrel adjuster clockwise until no play GENIUS 2016 BIKE USER MANUAL Y FOX NUDE SHOCK AND TWINLOC REMOTE CONTROL LEVER In the drawing of the shock and remote lever shown below you will see the parts indicated with numbers which will be used in the manual for the adjustment and setup Parts List S1 Front eyelet Shock Bolt S2 Rear eyelet Shock Bolt S3 Shock Housing S4 Rebound Adjuster Knob S5 Positive Chamber Valve S6 Remote Control Wheel Cable Fixing Screw hidden behind remote wheel S8 Shock Piston S9 SAG Indicator o ring on piston S7 Li Remote Lever L2 Release button L3 Remote Control Cables L4 Cable Tension Screw Fork Remote L5 Cable Tension Screw Shock Remote 2016 BIKE USER MANUAL GENIUS ENGLISH 11 6 3 tighten the cable and fix the cablefixing screw S7 by turning it clockwise with a 2mm allen key and a max tightening torque of 1 6Nm PF BASIC SET UP OF THE TWINLOC REMOTE CONTROL OF FOX NUDE SHOCK To ensure perfect function of the FOX Nude shock it is very important to follow the step
14. hox DNA 3 fork SCOTT Article number 230098 Please kindly note that the cable roll of a RockShox DNA3 or FOX CTD fork lever is not interchangeable with the regular rolls of 2 step forks You need to use another lever For more details please contact your authorized SCOTT dealer To change the rolls to match another fork brand pls follow the drawings below ROLL FORK UNMOUNTING ROLL FORK MOUNTING TORX T10 DT SHOT FOX CTD ROCK SHOX FORKS ROLL FIXATION DI FOX FORKS ROLL FIXATION 2016 BIKE USER MANUAL GENIUS ENGLISH 09 6 56 10 ENGLISH F ASSEMBLY OF THE REMOTE CABLE IMPORTANT Please make sure the lockout of SRAM RockShox or FOX fork is activated after transport correctly Therefore please compress fork 5 10 times before following the manual on remote cable installation and adjustment The lever should show on the downside of the cable roll the brand name of the fork you are going to use Please do not try to use a RockShox roll with a FOX fork or vice versa 1 To assemble the cable please bring the lever into the Descent Mode push the cable into the lever eyelet as shown on drawing below push it through the pre cut cable housing and fix it at the assembly unit on top of the right side of the fork crown FORK CABLE ROCK SHOX F _ 2 Fix the cable with the 2mm allen screw on the barrel adjuster on the fork crown with a tightening torque of 0 9Nm 8 Ib in cut the cable and s
15. imultaneous a blow off system prevents the shock being damaged in case the rider did not open the system while crossing obstacles 2 TRACTION RIDE MODE For Traction by reducing the internal chamber volume inside the shock the travel of the shock will be reduced to around 65 70 the characteristic of the air soring gets harder the SAG is shorter and the geometry steeper This results in climbing without bobbing and offers still optimum traction of the rear wheel For Ride by adding a platform on the compression damping system the shock will not bounce while standing on the pedals DESCENT MODE full travel of 150 130mm 700 900 You will find the following positions on the remote lever LOCK OUT MODE TRACTION MODE RIDE MODE DESCENT MODE D PRESS TO RELEASE 6 08 ENGLISH GENIUS 2016 BIKE USER MANUAL For the assembly of the remote control of the front fork lock out 2 different cable rolls which are changeable are existing The different roll for the pull of the fork remote cable can be changed within few minutes to adapt the lever to your fork model brand You will see on the downside of the roll the indication of the fork brand or the fork model SCOTT offers 2 different TWINLOC levers with following fork rear shock combinations FOX Nude with different rolls for FOX CTD fork and RockShox DNA 3 fork SCOTT Article number 230097 FOX CTD with different rolls for FOX CTD fork and RockS
16. ion 219574 complete set of RWS 142 12 Y FRONT FORK SET UP CHANGE OF FRONT FORK 219577 right side replaceable RD hanger For the set up of the front fork please use the fork specific manual attached to the bike We recommend using front forks with a travel of 150mm 700 130mm 900 and 2 135mm axle with RWS 135 5 140mm 700 Plus as this will not influence the geometry and alter handling of the bike This is available via the SCOTT distribution For details on the technical length of the recommended forks please refer to the Tech Info 219572 complete set of RWS 135 5 Chart before mentioned 219575 right side replaceable RD hanger F PIVOT MAINTENANCE 3 Regular 135mm rear axle with QR _ The pivot and bearings on SCOTT Genius are extremely easy to maintain This is available via the SCOTT distribution An external treatment with a grease spray after every bike wash is all you have to do We 206473 replaceable hanger do not recommend heavy grease sprays since these will leave a film on the parts which is difficult to remove We recommend the same for the chain also IF you have to change the bearings you can order them included in a service kit at your local If you want to use another RWS standard SCOTT also offers after market parts for specific SCOTT dealer or buy them with international parts number as shown above in the specs list wheelsets for the following parts via the SCOTT distribution in a hardware store 219574 R
17. ius The Carbon as well as the alloy frames of Genius can be fitted with ISCG chainguide systems A set of all spare parts for this action can be ordered via the SCOTT distribution with 229730 ISCG adaptor Genius 2013 Details for the assembly on the carbon frames of Genius The adaptor must be used in order to assemble the chainblocker on the ISCGO5 chainguide system You can assemble the chainblocker directly on the integrated ISC GO5 mount on the BB shell Please respect the different assembly positions for SRAM and Shimano front derailleurs P GENIUS CABLE ROUTING The direct and straight cable system on all our full suspension models offers perfect shifting performance combined with lightweight and high resistance against water and dirt Please note that you need to assemble the chainblocker exactly the way as shown below and use all parts of the set CARBON FRONT FRAMES Spacer The carbon frames of Genius have an internal shifting cable routing with cable stops on the front end of the Please also respect the different assembly positions for downtube as shown in the diagram SRAM and Shimano front derailleurs For 2x10 drivetrains you need to use 2x2 5mm washers for 3x10 drive trains 1x2 5mm washers between adaptor frame and the chainblocker as shown above 6 22 ENGLISH GENIUS 2016 BIKE USER MANUAL 2016 BIKE USER MANUAL GENIUS ENGLISH 23 9 Please note that the inner cables need to cross each other 1 ti
18. m 13 8 in 1122 7 mm 44 2 in 1121 8mm 44 2 in 1153 8mm 45 4 in 11529mm 45 4 in 1179 9 mm 46 5 in 11790 mm 46 4 in 1206 6mm 475 in 1205 7 mm 47 5 in BBC R H O TOPTUBE C R BBC R l O TOP OF 415 0mm 16 3in 4150mm 16 3in 440 0mm 17 3in 4400mm 173i 475 0mm 18 7in 4750mm 18 7in 510 0mm 201in 510 0mm 20lin SEATTUB J SEAT ANGLE 74 0 TAS AO TAS VANOS VAS 74 0 WAS K CHAINSTAY 439 0mm 173in 439 0mm 173in 439Omm 173in 4390mm 173in 439Omm 173in 4390mm 173in 4390mm 173in 439 0mm_ 17 3 in L REACH 4014mm 15 8in 4061mm 16 0in 428 7mm 16 9in 4334mm 17lin 4511mm 178in 455 7mm 179in 4721mm_ 186in 4767mm 18 8 in M STACK 588 8mm 23 2in 5855mm 231in 5981mm 23 5in 594 7mm 23 4in 6073mm 23 9in 603 9mm 23 8in 6212mm 24 5in 677mm 24 3 in N STEMLENGTH 60 0mm 24in 600mm 24in 7O Omm 28in 700mm 28in 800mm 31in 800mm 31lin 900mm 35in 900mm 3 5in 04 G GENIUS GENIUS NGLISH 05 9 F GEOMETRY TECHNICAL DATA GENIUS 900 700 PLUS GENIUS 700 s s M M L L XL XL PLUS LOW BB SETTING HIGH BB SETTING LOW BB SETTING HIGH BB SETTING LOW BB SETTING HIGH BB SETTING LOW BB SETTING HIGH BB SETTING JEAD TUBE A ida 675 68 0 675 68 0 675 68 0 675 68 0 Travel 130 90 Omm ANGLE Suspension B Eee UBE 100 0mm 39in 100 0mm 39in 100 0mm 39in 1000mm 3
19. m us app fox intelligent ride dynamics id549035102 mt 8 amp ign mpt u0 3D4 gt LIBRARY E Movies App Store gt Sports gt FOX Factory Inc DEVICES Ji music E Movies S FOX Intelligent Ride Dynamics FOX Factory Inc gt Free PLAYLISTS Ado de 5 4 90 s Music 4 Classical Music 16 Music Videos 10 My Top Rated 2012 FOX Factory Inc t Recentty Added 44 Recentty Played 4 Top 25 Most Played Rated 4 PRIVACY POLICY gt 169 Ibs S Pump tothe dicated DT EE 167 lbs 168 Ibs Description Set up your mountain bike shock and fork like a pro with the knowledge of FOX s ride dynamics experts all for free SETUP STARTS WITH SAG Unlock your bike s potential Whether it What s New in Version 1 0 8 posted 90 august 2 improved Overlay View Improved Accura Show All Versions v Information D per FOX Factory inc tegory Sports Updated 30 August 2012 Y m 1 0 8 Requires Compatible with iPhone Pod touch 4th generation iPod touch 5th generation iPad 2 Wi Fi iPad 2 Wi Fi 3G iPad 3rd generation iPad Wi Fi 4G ation iPad Wi Fi Cellular 4th generation iPad mini and iPad mini Wi Fi Cellular Requires OS 4 3 or later iPad 4th gener r w Languages English Chinese French German Italian Japanese Spanish 5 After downloading the app on your mobile gear please follow the steps shown in the app and inflate the shock according to the air pressure indicated 6
20. me on the inside of the downtube before you pull them out through the cable slot on the lower downside of the downtube Push the cables through the cable guide as shown below and fix the cable guide on the downtube with a 3mm allen key and a tightening torque of max 4Nm 35in Ibf Push the outer cable housings on the cables into the cable guide but make sure to respect the needed length as shown in the next drawing Please make sure to respect the 40mm distance between the cables and the BB bottom bracket housing to avoid ghost shifting and or damages on the shift cables and brake hose 6 24 ENGLISH GENIUS 2016 BIKE USER MANUAL For the rear brake please assemble the cable as shown 1 in the following drawings Please keep in mind to have a minimum distance of 40mm between the brake hose and the BB housing as abovementioned Please fix the brake hose and the remote seatpost cable housing Cif applicable on the frame on the cable mounts with the mount clips by following the routing info as shown below Please secure the clamps with a cable zipper as shown in the following diagram The cable guide can be ordered via the SCOTT distribution with parts number 229723 BB Cable Guide Genius f Carbon Frame 2016 BIKE USER MANUAL GENIUS ENGLISH 25 amp Please make sure to respect the 40mm distance between the cables and the BB bottom bracket housing to avoid ghost shifting and or dam
21. mp until the distance is 14 12 5mm Same for the FOX CTD on some of the Genius models if the distance between the main dust wiper seal is bigger than 14 12 5mm the air pressure of the air chamber is too low and should be increased by using the shock pump until the distance is 14 12 5mm _ x N im Pd DEDO F SET UP OF REBOUND FOX NUDE OR FOX CTD SHOCK FA TT NN VS Rebound describes the speed the shock comes back to its original length after absorbing A an obstacle Al By using the rebound adjuster knob S4 you can adjust the rebound step by step IMPORTANT After a dismantlement of the rear shock both fixing bolts should be tightened with a tightening torque of 10Nm 88in lbs If this is not done correctly the rear shock can be damaged G 16 GENIUS GENIUS 17 9 F SET UP OF OTHER SHOCK MODELS SCOTT strongly recommends using only the FOX Nude FOX CTD shock with the Genius bike as we designed both parts for a perfect matching combination with a linear suspension rate Also on those shock models the SAG should be 14 12 5mm Other Shock Models on Genius If you want to use a different rear shock model than the one originally on the bike please make sure that the shock will not in any position hit the frame and cause a damage to the frame Please follow the instruction below Please make sure that the rear shock or its accessory parts do not touch the frame when m
22. nsion technology Man 22 2mm x 6mm closes the gap between superlight dual suspension race bikes e g SCOTT Spark and the more new generation of all mountain bikes e g SCOTT Genius LT nee 22 2mm x 6mm Genius was designed for riders looking for a dual suspended trail and marathon bike offering Seatpost A Baan a maximum rear wheel travel of 150mm 700 130mm 900 700 Plus diameter semi integr for tapered 11 8 1 5 44 54 9mm SCOTT does not see frame and rear shock as single components which are assembled Headset Inner diameter of frame or with 11 8 straight together on a bike but as a concept with all these components working together and 44 0mm offering an outrageous function by matching perfectly Fork travel 150mm The Genius Concept is based on a multi pivot technology Fork length 344mm BB housing BB PF 92 The damping performance was improved in comparison to the already famous old Genius and with reworking also the kinematics we were able to reach a better progression in the end of the stroke travel of the swingarm Front derailleur Bearings Shimano E Type SRAM S3 direct mount 2 x IGUS 6 x 6802 24 x15 x 5 Max Tire Width 57mm 2 25 The SCOTT system using the Nude shock named TC Traction Control will allow you to reduce by remote control the rear wheel travel from 150mm 700 130mm 900 700 Plus to 100mm 700 90mm 900 700 Plus including a more progressive spring rate but still offering a supple break aw
23. ounting or suspending For doing so release the air remove the coil install the shock and compress the shock completely lf the shock touches the frame while doing so do not use this shock in order to avoid damage to frame swingarm or shock PFP HEADSET OPTIONS Headset Pro Zero Logic Press Fit Taper 18mm Genius features a tapered headset and fork steerer system to match with semi integrated headsets of the 50 61 mm range with ID of Headtube of 44 0mm on top and 54 9mm on the lower end 43 PA Stack Height 15 2 2 8 18mm Z 4 6 N w jon Material Q TY Rema SA UNIT mm PART PRD 13641 0E Tapered 054 9mm Ritchey WCS Carbon Zero Tapered PF 50 6lmm 18mm UD PRD 13636 Ritchey PRO Tapered PF 50 61mm 12 9mm PRD 13640 G 18 ENGLISH GENIUS 2016 BIKE USER MANUAL It is also possible to use forks with a standard 11 8 steerer tube when using a reducer headset such as e g Ritchey WCS Carbon Zero Tapered PF 50 61mm 18mm UD for 11 18 fork PRD 14860 Y BOTTOM BRACKET BB ON GENIUS All frames of Genius carbon and alloy have a BB shell for BB92PF standard This matches to several bearing and crankset models of Shimano SRAM FSA and others Please note that you do not need anymore a spacer on the right side of the bearing cup between frame housing and bearing cup BB carbon frames PF92 ID41mm No spacer BB alloy frames PF92 ID41 mm No spacer
24. ranty claim given that it provides evidence of purchase Otherwise no warranty is granted In principle this warranty is granted worldwide Claims must be made through an authorized dealer for information regarding the nearest dealer write or call this company or the national SCOTT distributor Normal wear accident neglect abuse improper assembly improper maintenance by other than an authorized dealer or use of parts or devices not consistent with the use originally intended for the bicycle as sold are not covered by this warranty Hereby SCOTT grants a voluntarily manufacturer s warranty Additional entitlements according to national warrant of merchantability are reserved For warranty info on the Fox Nude shock please refer to the attached manual of Fox Nude BIKE USER MANUAL GENIUS ENGLISH 31 9
25. s shown below exactly On Genius Carbon frames you will find an internal cable routing Push the inner cable first through the remote lever in On Genius alloy frames a regular the upper cable routing of the lever and then through outside cable routing the outer the cable housing as shown below inside the toptube cable housing is fixed on cable mount ports with cable zippers 4 Check that the handlebar lever is in the traction position Refer to the following diagrams 5 cut the cable approx 20mm away from the remote wheel Fix it by squeezing it with pliers 1 loosen the cable fixing screw S7 by turning it counter clockwise with a 2mm allen key 6 push a cable end cap on the cable until it touches the end of the cable Fix it by squeezing it with pliers 2 insert a new cable via lever hole and cable housing and push it into the shock as shown around the remote wheel S6 6 12 ENGLISH GENIUS 2016 BIKE USER MANUAL 2016 BIKE USER MANUAL GENIUS ENGLISH 13 9 PF BASIC SET UP OF THE TWINLOC REMOTE CONTROL OF FOX CTD SHOCK The assembly of the remote cable and the setup of the FOX CTD rear shock is very similar to the abovementioned assembly and setup of the FOX Nude For more details on the FOX CTD please follow the details shown in the manuals of FOX attached to this bike F RECOMMENDED TOOLS FOR THE SHOCK SET UP For the set up of the shock we recommend to use a shock pump with a scale up to 20 bars
26. y an authorised SCOTT dealer The authorised SCOTT dealer shall confirm the effected annual maintenance service by stamp and signature In case such an annual maintenance service has not been effected the warranty of 5 years for the frame shall be reduced to 3 years Costs for maintenance and service have to be born by the owner of the SCOTT bike On Gambler Voltage Fr and Volt X the warranty period is limited to 2 years The warranty period starts at the day of purchase This warranty is limited to the first buyer what means the first person who uses the bike and only with the use it was made for Furthermore this warranty is limited to purchases via authorized SCOT T dealers The warranty is solely granted in case of purchase of a completely assembled bike to the explicit exclusion of purchases of not completely assembled bikes In case of a warranty claim the decision to repair or to replace the defective part is up to SCOTT Non defective parts will only be replaced at the guarantee s own expense Fair wear and tear is not covered by the warranty A complete list of all parts of wear and tear can be found in the next chapter of this manual In addition you will find at the end of this manual a protocol for the handing over of the bike which will remain in copy at the SCOTT dealer after acceptance and signature of the consumer It is obligatory to show this protocol of handing over together with the defective part in case of a war

WWW.SCOTT-SPORTS.COM

Contents

Download Pdf Manuals

Related Search

Related Contents