Home
user manual
Contents
1. DMX address using 105 64 41 Turn on dip No 7 DIP SWITCH DMX VALUE simple maths 41 32 9 Turn on dip No 6 9 8 1 Turn on dip No 4 1 1 0 Turn on dip No 1 1 1 You will most likely use the first available number which maybe Number 1 This number was selected for WOON AU AWN w N example purposes jo Equinox Constella Laser DMX set up DMX 512 e DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX Linking e DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA
2. between pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number CABL90 will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors e Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The Chart below details the correct cable conversion Bon canon socket in 1 GND screen Pin 2 N C Pin 3 N C i 5 Pin canon socket 3 Pin canon socket Pin 1 GND screen Pin 1 GND screen Pin 2 signal Pin 2 N C Pin 3 v Ag Pin 4 N Pin 3 N C Pin 5 N C Equinox Constella Laser DMX DIP SWITCH SET 0 OFF 1 FE 4 oa L EN a Dip Switch position Dip Switch Reference Chart DMX Dip Switch Quick Reference Chart Dip Switch Position aaa 1 efe or r fier res 2 r a GUL MEIER 3 ffer e rar 5 1195 f 22r 250 aon f 22 355 a7 aro far 485 35 e oo Fae Tee 196 aw 200 202 T 324 286 saw a0 aoe ST fee FOr 135 5 Far 229 26r 23 225 f aor 360 aoe aes aa e 3870 102 132 6 108 220 262 20a 228 f 35e 300 f 422 ase ABE T f frr r fres aT Hoe aT 265 2 ser f ae sor aes aes aa e a0 72 04 136 Tee 200 232 267 256 328 360 302 227 256 488
3. audience Because the laser output beam can scan people s faces it carries a risk that it could cause damage to eyesight if over exposed to the laser beam Maximum Permissible Exposure MPE The amount of laser light that a person can be exposed to without it causing harm to eyesight is Known as the Maximum Permissible Exposure or MPE These levels are set down by the British Laser Safety Standard BS EN 60826 1 When people are exposed to laser light output which is above the MPE it may potentially pose a risk of causing eye damage Calculating what the MPE and exposure level is for a given laser effect is quite a complicated process and it is dependant on a whole number of factors and conditions The laser safety standard BS EN 60825 1 contains the information and data required to calculate these levels Equinox Constella Laser Safety Laser Safety Officer The BS EN60825 1 Laser Safety Standard recommends that all venues that use or businesses that work with Class 3B laser products should appoint a Laser Safety Officer LSO The Laser Safety Officer should be aware of the many safety issues when using lasers and will also be responsible for overseeing how the laser is used In smaller businesses the LSO could be the installer operator or owner etc Separation Distances Health and Safety guidance details that for supervised installations of lasers which are above the Maximum Permissible Exposure MPE should not be accessibl
4. ro at 73 105 frar oe 201 223 265 27 228 Ser 305 225 f a7 aoe AO a2 7a 106 13e 7 202 234 268 200 220 f aez 0a a28 a f s TOT rae farr 20 f 2s 207 Poe ae ae 305 ACE Piz aa 7e FOR 120 f a72 204 236 26 200 332 f 36a 306 225 f a0 faor aa for Oe fiar fara 205 f aar 68 aon as f aes aor a2 far faos va a6 7e AO 122 f 17a 206 28 270 f 302 334 206 308 430 262 aor 7a 7 16 a8 ao 112 1an 76 208 280 272 304 336 368 400 232 264 496 UAE aoe Bar 27S aos EEA 8 BO fez 11a 126 fara 210 282 27a T a06 28 f avo 402 f ase aes ae nefer es m rar ae Bae fe 27s faor 2 for as as far 490 25 2 ea 116 tae 100 212 284 278 200 220 372 aoe 236 f ae f SOO HOKEJE 285 277 aoe 732 EALA CACEN 22 s4 e6 118 160 ea 214 226 278 310 342 374 406 238 aro soz 24 56 aa 120 162 184 216 24B 280 T 312 344 376 T 408 440 a72 f 504 25 BT es TAH 165 a5 PAT Bao Dar f ara 28 f arr GIK SOE 25 5590 122 154 am 218 250 252 ea as f are a aaa ara SOE a f for 2 iss aT 2 Bat 2 f a ar fore GIK SOT 2 er os 12 157 f a 221 253 05 AT 20 f aer ATS aes farr SOE 30 e2 oa 125 15e 222 25 205 ew 280 f aez a 245 fare STO DMX Address Equinox Constella Laser Safety Class 3B Laser Safety Guide Warning Class 3B Lasers have the potential t
5. 11 On Off switch 7 Microphone 12 ILDA Input LED 8 Power input 13 DMX Input LED Equinox Constella Laser Operation modes Operation modes The Constella has five modes of operation as follows 1 Sound active mode To select sound active mode set all dip switches to OFF You can now use the sensitivity control on the back panel to set the required sound level 2 Auto pattern mode To select auto pattern mode set dip switch 1 to the ON position and all others to OFF The Constella will now cycle through all it s internal geometric patterns 3 Auto animation mode To select auto animation pattern mode set dip switches 1 2 to the ON position and all others to OFF The Constella will now cycle through all it s internal animation programmes such as a numbers running dinosaur and flying bird etc 4 DMX mode To select DMX mode set dip switch 10 to ON You can now set the required DMX address using dip switches 1 to 9 Please refer to the chart below for DMX functions The DMX address starts at 1 5 Slave mode To set the unit s in slave mode set dip switch 2 to the ON position and all others to OFF The Constella laser will now run in sequence with the master unit DMX function chart crano omxaaaress Fuon OOOO O mx aa ms TT we No function Equinox Constella Laser DMX control mode DMX function chart cont Dotted image CH 10 CH 11 CH 12 6 127 Draw image slow to fast 128 255 Draw image and r
6. EQUIN X CONSTELA Order code EQLA23 user manual Equinox Constella Laser WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty Equinox Constella Laser Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment e Do not open the equipment and do not
7. able below Laser Output Power 10mW 30mw 50mW 100mW 250mW 450mWw Hazard Distance 12m 20m 25m Note The above values in the table have been calculated assuming the characteristics of a typical laser which has a beam spread of 2mradians Not all laser units have the same specification Remember Static laser beams are hazardous for long distances so it is recommended that the laser beams are projected overhead and not into the viewing audience Laser Safety Books The Radiation Safety of Display Laser Installations HS G 95 Published by HSE Books 1996 ISBN 0 7176 0691 Health amp Safety Executive Website www hse gov uk Laser display safety guidance page www hse gov uk pubns INDG224 htm Health Protection Agency Website www hpa org uk
8. assigned to address 1 to that unit no matter where it is located in the DMX chain DATA Cable DMX cable requirements for DMX operation e The Equinox Constella laser can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output figure 1 Figure 1 Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight dealers Please quote CABLI10 2M CABL11 SM CABL12 10M Also remember that DMX cable must be daisy chained and cannot be split Equinox Constella Laser DMX Set Up Notice e Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR se ee XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground i 1 ground 9 cold Pin 1 Ground Pin 2 Negative FIGURE 3 FIGURE 2 Special Note Line termination e When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behaviour Termination reduces signal transmission problems Q and interferance it is always advisable to connect a e DMX terminal resistance 120 Ohm 1 4W
9. be harmful to eyesight if viewed directly The injury that a Class 3B laser can inflict is dependant upon several varients including the amount of time the laser beam enters the eye for the intensity of beam and what part of the eye that actually receives the beam The part of the eye which is most susceptible to receive damage from the beam is the retina The retina is the part of the eye that receives the light signals that are sent to brain All light entering the eye gets focused onto the retina Normal light sources including halogen lamps are not usually harmful to view Lasers are different in the fact that they can get the beam focused down to a very small point on the retina which can burn holes on the back wall of the eye There are no pain receptors on the retina and the damage can happen in less time than it takes for a person to blink so the person will be not be aware of any damage taking place Damage to the retina cannot be repaired and therefore is permanent Symptoms include severe loss of sight and unnoticeable vision loss Equinox Constella Laser Safety Licensing and Laws There are no U K laser laws or any laser licenses that need to be obtained in order to own or operate a laser for lightshow use Detailed and specific guidance is issued by the Health and Safety Executive in the form of a book called HS G 95 The Radiation Safety of Lasers Used for Display Purposes Class 3B Laser Safety Features Class 3B la
10. e to persons in the audience Also recommended is an area where the MPE may not be exceeded and extends from 3m above to 2 5m laterally from any point in the venue where the public may have access during the lightshow The illustrations below show the separation distances Separation Distance Drawing Emitted Beams LASER 3 metre Height MPE must not be exceeded Emission may exceed the applicable MPE ata height exceeding 3 metres Emission may exceed the applicable MPE 2 5 metres 2 5 metres Audience exclusion zone LASER Plan View showing the 2 5m horizontal seperation distance Note The 3 metre height specified is not the height of the actual laser unit but it refers to the height of the laser beams emitted Equinox Constella Laser Safety Hazard Distances All lasers for display purposes feature a characteristic called the hazard distance for direct viewing NOHD The NOHD is distance at which viewing the laser directly is no longer considered a hazard Note at any point between the laser unit and the calculated hazard distance it may be hazardous to directly view the laser beams Exposing the eye to the laser directly from outside the hazard distance is considered to be no longer a risk The most dangerous senerio is to look directly at a static single beam because all the light energy is concentrated into one small point The hazard distances for various different powers of Class 3B laser are shown in the t
11. modify the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors e Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable e Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically e If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again e If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service e Only use fuses of same type and rating e Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS e WARRANTY One year from date of purcha
12. o harm eyesight if viewed directly and can also be harmful at long distances Any unit that contains a laser diode has to be classified depending upon the light output that someone may be exposed to All laser products are classed as defined in the Laser Product Safety Standard BS EN 60825 1 The classes range from the safest which is Class 1 through to the most hazardous which is Class 4 A laser diode that emits more than 5mW of light and less than 500mW can be classified as a Class 3B product Operation and installation Notes Laser effects should only be installed and operated by persons who have been trained in how to operate laser effects safely Laser effects should be located in a safe and secure position in the venue so that once installed it cannot be tampered with by unauthorized users Before operation the path of the laser beams should be taken into account in respect to how the beams will scan the viewing audience If direct audience scanning is to be used then the laser energy levels from the effects needs to be calculated Health lf used responsibly and in accordance with the relevant guidance issued by the Health and Safety Executive a laser effect will not present a hazard to those viewing the show as long as the laser beams are projected over the heads of the viewing audience When laser effects are directed into the audience area it becomes difficult to tell if the effects are causing harm Class 3B laser beams can
13. se OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Equinox Constella Laser Technical specifications You should find inside the Laser carton the following items 1 Constella Laser 2 Power cable 3 User manual Technical Specifications DMX channels 12 Laser diodes 1 x 50mW Green 532nM DPSS laser 1 x 150mW Violet 405nM DPSS laser 1 x 200mW Red 650nM DPSS laser Operating modes 1 Sound Active 2 Auto Run 1 patterns 3 Auto Run 2 animations 4 DMX 5 Slave Power consumption 24W ILDA compatible Power supply 240V 50Hz Dimensions 380 x 275 x 174mm Weight 5 1Kgs Fuse 2A Features The Constella features 12 DMX channels and many laser patterns and animations that are ideal with or without fog Back view SS WWW PROLIGHT CO UK oTi 2 7 INR Wee ws an mi A 2 Q S DIP SWITCHES DMX QUT AC 440V 2A ICROPHONE Identification aL 6 4 1 Key lock D 2 Cooling fan 3 DMX In 4 DMX out 9 ILDA input 5 Audio sensitivity control 10 Image size control 6 Dip switches
14. ser products need to be fitted with specific safety features These features are issued in the British Standard on Laser Product Safety BS EN 60825 1 and are a needed for the product to meet CE approval The important warnings are listed below 1 Emissions Indicator 2 Remote Interlock Connector 3 Laser Safety Warning Labels Summary of each Feature Class 3B lasers need to contain three very important Laser Safety Warning Labels the starburst symbol aperture label and the warning classification label The starburst is used to indicate that the product is a laser product The aperture label is located next to the appature to show where the laser emits it s beam s The warning classification label details the class of the laser product the maximum output power and the wave length s colours of the laser along with a Laser Radiation Avoid Exposure To The Beam warning The Remote Interlock Connector will only allow the laser to function when the two pins are shorted together For lightshow use it is recommended by HS G 95 laser safety guidance laser effects can be overridden by a remote Emergency Stop switch The remote interlock connector provides a convenient way for such a switch to be easily added to the laser system to provide this control The emissions indicator is fitted to indicate when the laser is ready to produce a light output Audience Scanning Audience Scanning is when laser beams are directed at the viewing
15. ub out slow to fast Pp a DMX Control Mode Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independently Setting the DMX address The DMX mode enables the use of a universal DMX controller Each fixture requires a start address from 1 511 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 105 and 106 Choose a start address so that the channels used do not overlap E g the next unit in the chain starts at 107 Set the start address using the group of dip switches located usually on the back of the fixture Each dip switch has an associated value Adding the value of each switch in the ON position will provide the start address Determining which switches to toggle ON given a specific start address can be accomplished in the following manner By subtracting the largest switch value possible from the selected start address until zero is achieved EXAMPLE STARTING ADDRESS Address 10 Pin NO 4 8 Pin NO 2 2 Total 10 Address 24 Pin NO 5 16 Pin NO 4 8 Total 24 e 3 233 128 105 Turn on dip No 8
Download Pdf Manuals
Related Search
Related Contents
LG 42LB5610 42" Full HD Black LED TV BARD® MONOPTY® Disposable Core Biopsy Instrument 高病原性鳥インフルエンザ防疫マニュアル 基本(表紙~P54 Agilent N9330B Handheld Cable & Antenna Tester User's Guide Cours de Révision Amasoft MFTS - Manual do usuário - Projeto Bom Manejo Copyright © All rights reserved.
Failed to retrieve file