Home

NEW Products & Special Offers

1. Code HCP26 single white Code HCP26D double white Code HCP26S single steel Code HCP26SD double steel Single gang flat brushed steel Code HCP26FS 39 99 A wall outlet plate with a HDMI socket at the front and an angled HDMI socket at the rear A a deep 47mm back box is recommended Depending on the size of the plug on the HDMi cable used some modification to the pattress may be necessary Code HCP26G 19 99 A wall plate with a HDMI socket at the front and a HDMI socket at the rear connected via a short 10cm flexible cable Ideal for situations where the rear HDMI cable is drawn through from unusual angles Depending on the size of plug used some modification to the pattress may be necessary Code HCP26FC white DVI Plug to HDMI socket Adaptor Code KA170 9 99 HDMI adaptor type C mini socket to type A plug Code KA189 6 99 HDMI adaptor type A socket to type C mini plug Code KA190 7 99 Mini Display Port to HDMI adaptor cable 15cm Display port male to female HDMI 19 99 Code MDPHDMI Back to back coupler for joining HDMI cables HDMI socket to socket coupler Code KA173 6 99 HDMI hinged 90 degree coupler Code KA173H 14 99 Professional HDMI socket coupler in Black D shaped XLR cutout ideal for use in patch panels as well as wall and floor plates Silver finish Code KLC123 CAT5 amp Networking Cabling UTP CAT5E Cable Unshielded 4 p
2. Code RNTG1 149 00 Best suited to camcorders with mini jack mic sockets Rode NTG2 phantom or battery Code RNTG2 159 00 Optional Dead Cat furry windjammer is available for this mic Code DEADCAT 24 99 Rode RNGT2 Kits Money saving kits NTG2 plus RBP Boompole RSM3 suspension shockmount amp Deadcat Windgag Code RNTG2BK 279 00 NTG2 plus an RSM3 suspension shockmount amp Deadcat Windgag Code RNTG2CK 209 99 Code ATBM 2 5 99 Rode Lavalier Microphone Whether you re presenting for television or live on stage in a 20 000 seat auditorium or in a house of worship The RODE Lavalier microphone has your needs covered Featuring the pure clear audio and low handling noise that R DE is celebrated for the LAVALIER is built to deliver and to last The included water resistant pop filter and mini furry for high wind protection ensure quality recordings in adverse environments while the anti trauma water resistant case provides rugged and secure protection for the microphone cable and accessories e R DE MiCon connector system provides seamless integration with a wide range of wireless systems while maintaining discreet and unobtrusive appearance Features e Ultra discreet appearance e Incorporated cable management system e 04 5 mm G0 177 miniature microphone e Corrosion resistant stainless steel Low handling noise e Gold plated connections micon connectors sold separately see
3. If you are sending a line level signal to a room then sometimes you ll have direct control of the source and just want to amplify the audio signal in the room without needing any other form of control The Keene KLAB20DS slave amplifier will do this job perfectly It is designed to be a fit and forget solution to powering additional and remote pairs of loudspeakers Once installed it will automatically switch on whenever audio is detected and switch back again to an ultra low power standby mode when no audio signal is present Ideal for feeding line outputs from from say Squeezebox Sonos etc Code KLAB20DS Amplifier only 109 99 Code KLABKITDS Amplifier amp PSU 129 99 Code KLABPSU 15v DC 4A power supply 29 99 Bookshelf Speakers High quality 4 dual cone full range mini box speakers Solid ABS Construction with Quick Connect Speaker Terminals e 4 Full Range Mini Box Speaker System e Dual Cone Full Range Speakers e 12 Oz Shielded Magnet e Power 80 W Max e Quick Connect Speaker Terminals e Dimensions mm 120x120x132 e Impedance 8 Ohms e Power 40W RMS e Frequency Response 80Hz 20kHz 18 99 18 99 Code B406A Code B405A BLACK per pair WHITE per pair HQ Wall mounted loudspeaker volume control Suitable for UK standard electrical double pattresses 47mm deep White facia with chrome colour knob High efficiency transformer design with max power handling of 60W rms Will accept cable
4. The removable camera quick release plate is fitted with a sliding screw for fine adjustment and is made from extraordinarily strong magnesium alloy A disc calliper is used for the tilt brake to hold the head rock steady and a 75mm ball head makes levelling smooth and steady Specifications e Height fully extended 155cm Height folded 75cm e Camera load capacity 4Kg e Ball base 75mm e Weight 3 75Kg Supplied with padded carry case Te Bele m h i Pei ee FT PDE iL oe Le Code TH950 279 00 Spare quick release plate Code TH650PL 49 99 Find product information TPV1 Video Tripod High quality Camlink TP Video Professional Tri Leg tripod including soft carry case Ideal for both amateur and semi pro applications where a good quality stable tripod is required Specifications e 3 Section Tri Legs Removes whip at the start of a pan Friction Fluid effect Damping Head e With 2 Handles e With Quick Release Plate e Ball Leveling e Spirit Level e Rubber Feet e Tilt Range 83 FOI e Pan Range 360 e Max Operating Height 137cm Folded Length 73cm 125 95 TPV1 Video Tripod Kit Deal Code TPV1 A complete kit containing the Konig branded version of the excellent TVP1 Tripod above together with a Konig tripod Dolly 169 00 Code TPV1KIT Libec Tripod Dolly Designed for use with the TH650 tripod but also works well with the TH950 It is folda
5. 1 4 screws e Distance between dual point fixings Min 45mm 1 8 Max 67mm 2 6 e Alternative mounting platform supplied for speakers without fixing hole e Supplied in pairs e Maximum Weight 2Kg 4 4lbs e Minimum Height 685mm 27 e Maximum Height 1060mm 42 Code BT114B 30 95 Email your order to us at sales keene co uk Camera Suppports LIBEC TH 650 Tripod amp Head An extremely high quality tripod at a great price the fluid head has a counterbalanced mechanism which compensates for the camcorders weight and holds it steady at any tilt angle The head also has a 65mm claw ball which allows for quick and easy head levelling regardless of leg position The legs are made from three section oval pipe which gives good rigidity and also have a transport lock to hold them in place when on the move Specifications e Height fully extended 150cm Hieght folded 75cm Weight 3 2kg e Camera load capacity up to 4kg Tripod section Single stage e Supplied with carrybag Code TH650 169 00 Spare quick release plate Code TH650PL 24 99 LIBEC TH 950 Tripod amp Head Due to smaller and higher performance hand held camcorders constantly entering the market the industry enjoys an increasing demand for tripods and heads for such camcorders Ever since it was introduced the competitively priced high performance TH 950DV has been one of the world s most popular tripods in its class
6. It also features an ae vie second only releasing them again when the code emitters electronically isolated Direct input allowing direct sequence is complete It also features a direct cable e USB power option connection to the IR Blaster output from any other manufacturers products very useful with CAT5 Extenders where the single Blaster output cannot control all of the source equipment input to redistribute other manufacturers IR Blaster outputs and it can drive up to four dual power IR emitter outputs The flexible design allows for a number of configurations that will solve most IR control problems pe OY amp unuon Ampifur Pike s in stio The unit is very flexible allowing for a number of configurations that will solve most IR control problems e USB Power Connection e Compact Size 60x35x20mm e Dual IR Outputs e Standard IR Receiver Input a the ma ae eee aa a Receiver ae istribution amplifier ower Cable and a IRBKIT Mini with Fascia Mount i IRPKIT4S2 Is the Basic kit plus a Standard IR receiver mains adaptor l and two universal IR emitter wands Receiver IRBKIT Mini supplied with a Fascia mount receiver and a single emitter This is designed to allow IR control of devices out of sight behind the display or cabinet An additional IR emitter may be added later if required Supplied complete with a mains to USB power supply Code IRBKITMF 65 17 Also available without the
7. Sending an AV signal down a long cable run up to 100m with the right cable Making up to four simultaneous recordings from one source Sending line level audio to amplifiers in other rooms Specifications e Power 12 18v DC 300mA or greater mains adaptor included e Video bandwidth 50MHz distortion lt 50db up to 10Mhz e Back terminated series 75ohm outputs for reflection free performance e DC coupled on Composite video and Luminance outputs a N e AC coupled on Chrominance output e Slew rate up to 1000v uS e Audio distortion lt 0 1 bandwidth 20 30kHz e Audio output impedance 1K ohms each output e Audio input impedance gt 10K ohms e Dimensions 144 x 111 x 64mm e Weight 680g exc supply amp cables Code KDA 684 99 Email your order to us at sales keene co uk HDMI Distribution Amplifiers Each product in the Quantum Distribution Amp Series is compatible to V1 3 specifications Besides splitting and distributing this HDMI V1 3 Distribution Amplifier also does signal amplification and equalization so as to provide high performance for both audio and video Features e Compliant with HDMI 1 3 HDCP 1 1 and DVII 0 standards e Supports a wide range of PC and HDTV resolutions from VGA to UXGA and 480i to 1080p e HDCP keysets allow each output to work independently when connecting to a HDMI display HDMI cable distance test with 1080p resolution at 30 metres for both video and 5 1 audio when using
8. and it can even be personalised for different members of the family e Personalise the remote control for each member of the family favourite channels for you your partner children and up to 10 others e Guaranteed to work with all your current and any other A V equipment you purchase In the future extremely comprehensive pre programming with learning facility e In addition to 10 A V devices TV decoder DVD set top box etc you can also operate the Marmitek X 10 modules used for operating lighting and electrical appliances e With handy home theatre macro function with 1 press of a button you can switch all your equipment and X 10 lighting to the correct setting 68 00 Code EZICON Standard Additional bag Remotes for Sky Sky Digital Satellite Systems Remote Why would you want another Well if you had extended control of your Sky system from other rooms then you might not want to or remember to carry your single remote controller from room to room Solution have a remote wherever you might want to use one Simple as that Code SKYREM e1 2 x 99 POWERMID KIT DEALS This is a Powermid XL kit that includes one extra IR receiver so you can control your equipment from two different rooms Code PMIDKIT1 3 9 99 Powermid XL kit including a Powermid Eye twin IR emitter wand to control two extra devices Code er 2 9 99 Powermid XL kit including one extra IR receiver RF tr
9. bluetooth grey Architectural Speakers for use in Walls or Ceilings e Pivotal tweeters allow high frequencies to be focussed e Removable mesh grills e Frame allows for ceiling or wall board mount without extra brackets e 8 ohms 203mm Circular CMS5U e Frequency response 80Hz 20kHz e Power 25W RMS e Overall Diameter 203mm e Panel cut out 165mm e Sound pressure level 89dB 4 273mm Circular CMS8U e Frequency response 60Hz 20kHz e Power 30W RMS e Overall diameter 273mm e Panel cut out 238mm e Sound pressure level 90dB 69 99 89 99 Code CMS5U Code CMS8U Rectangular B411A e Directable Titanium dome tweeter e Power 50W RMS e Overall Dimensions 305x218x77mm e Cut Out Dimensions 275x185mm e Frequency response 80 20kHz Rectangular Subwoofer B415A e Frequency response 30Hz 3kHz e Power 90W RMS e Overall Dimensions 367x367x88mm e Cut Out Dimensions 329x329mm e Impedance 8 Ohms 34 99 34 99 Code B411A Code B415A per pair single speaker Single Speaker with Dual Coil amp Stereo Connections Ideal for smaller installations where you don t really have the room or need to fit two loudspeakers this orovides both left and right stereo channels from a single point whilst maintaining channel separation ge The speaker has twin connections so you LO A f F simply run both left _ and right speaker cables
10. quality cables e HDCP Compliant e Supports DVI source and DVI display by using DVI to from HDMI adaptor cable Code QU12S 1 input to 2 outputs 148 04 Code QU14S 1 input to 4 outputs 287 30 Code QU18S 1 input to 8 outputs 415 79 CYP HDMI 1 to 8 Distribution Amplifier with System Reset Each splitter in the Quantum Distribution Amplifier Series is compatible to v1 3 HDMI specifications supporting Deep Colour together with High Definition Audio Each buffered output can run 1080p up to 15 metres and can also be cascaded Features e v1 3 HDMI HDCP 1 1 and DVI 1 0 compliant e HDMI 1 to 8 Splitter with System Reset function e Resolutions supported PC VGA to UXGA HDTV 480i to 1080p plus 1080p24fps e High Definition Audio supported Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio plus LPCM e Auto signal amplification amp equalisation improves signal transmission distances e Supports CEC bypass e Supports Deep Colour 10 amp 12 e Selectable EDID settings TV downstream and STD fixed e Power amp SYNC LED s indicator e Supports 3D signals Specification e Input 1 x HDMI female port e Outputs 8 x HDMI female ports e Power 5V 5A DC e Gross Weight 1240g e Net Weight 1000g Code QU8MS 3 07 a 65 AV Switching amp Distribution HDMI Distribution Amplifiers These Coosis HDMI Distribution amplifiers are compact devices that give multiple simultaneous HDMI out
11. 59 99 Universal Soundbar Mount The ideal solution for mounting a Soundbar Speaker to your Flat Screen TV e Mounts a Soundbar above or below the screen e Universal mount suitable for most soundbars and flat screens e Use with or without a flat screen wall mount e Ideal for corner installations with an articulated mount e Low profile steel brackets e Max weight of Soundbar 10kg 22Ibs e Easy installation All mounting hardware included 24 79 Code BTV914 BT77 Ultragrip Clamping Speaker Mount The BT77 Ultragrip Pro Side Clamp Loudspeaker Wall Mount is ideal for loudspeakers with curved fronts and suitable for all types of small to medium loudspeakers The BT77 clamps loudspeakers at the side using Ultragrip high friction pads eliminating the need to screw into the loudspeaker e Modern aesthetic design with coverplate hides fixing screws e Slim line wall bracket ideal for stud partition walls e Simple adjustment one 13mm locking nut secures tilt and swivel e Complete fixings kit for wall mounting included e Available in Black or Silver e Speaker Width 135 280mm e Speaker Weight Max 25 Kg e Tilt 7 degrees Up or Down e Swivel 180 Left or Right e Supplied in pairs Code BT77 black 34 99 Code BT77S silver 34 99 Code BT77W white 34 99 LCD Wall Mount with tilt amp swivel up to 23 Designed for screens up to 23 58cm 15kg 33lbs Full motion mount ideal for corner m
12. Embedder lets you insert an external audio signal into any HDMI source The device allows you to insert analogue or digital stereo and multi channel digital surround sound signals via Optical to give users the capability to overcome audio issues within complex HDMI installation The AU 11CA also repeats the HDMI signal to allow an extended total HDMI cable range Features e Compliant with HDMI v1 3 HDCP 1 2 and DVI 1 0 e Supports Optical Sample Rate up to 96 kHz e Supports LPCM Stereo DTS and Dolby Digital via Optical input e Supports up to 24bit resolution digital audio e HDMI cable distance testing showed that with 1080p 8bit 12bit resolution the input output distance is up to 10 meters e Low power consumption e Supports HDMI Sample Rates up to 192 kHz Specification e Inputs 1 x HDMI 1 x Optical 1 x Analogue Stereo 2 x RCA e Outputs 1 x HDMI e Power 5V 1A DC US EU standards CE FCC UL certified e Dimensions 85 D x 85 W x 35 H mm Code AU11CA 1 22 31 HDMI Audio De Embedder 5 1 with built in repeater The AU 11CD is an advanced solution for repeating HDMI with integrated Audio de embedding up to 5 1 Connect the AU 11CD between your source and display via HDMI and select the audio format required Features e Compliant with v1 3 HDMI HDCP 1 2 and DVI 1 0 e Supports HDMI Sample Rates up to 192 kHz e Supports Optical Sample Rate up to 48 kHz e Supports TMDS clock frequency rate 225MHz e Support
13. Manual override button for each switch e Optionally use internet time servers to set internal clock e Internal Real Time Clock IC with 5 year battery backup Mains Conditioner For Home Cinema And Hi Fi A useful upgrade for any setup this is an affordable yet extremely well designed unit that delivers impressive results This unit contains a powerful Mains Conditioning Filter which will reduce or eliminate mains interference coming through the mains electric supply and help to enhance your sound and picture quality It also incorporates Surge Protection for complete piece of mind Specifications e Max Current rating 13A e Max Surge Protection L N 6500A L E 4500A N E 4500A e Max Voltage Spike Protection 6 000 Volts Features e 2m Screened Mains Lead to prevent RFI What Hi Fi Magazine gave this a 5 star Award The six way mains conditioner delivers truly dynamic audio gains Comparing it s performance to the unconditioned sound our reference CD Amp system enjoys greater separation and focus of sound and greater clarity and confidence in the mid range Bass is burlier and better integrated too In a nutshell It really does work oe Code CS929 2 9 z 99 X10 Appliance Module AM12 Appliance Switch Module Simplicity itself just unplug the device you want controlled plug this into the socket then plug the device back in Set the X10 address as needed and you now have instant X10 con
14. and high SPL capability usually only featured by some of the most expensive microphones Now available as the Complete Vocal Recording Solution this NT1 A package now includes everything you need to get truly professional vocal recordings the world s quietest studio microphone a studio grade pop shield and shock mount a premium 20 cable dust cover an instructional DVD with recording tips and of course RODE s industry leading ten year warranty Large 1 25mm capsule with gold plated diaphragm Cardioid polar pattern Self noise of only 5dB A Ultra low noise transformerless surface mount circuitry Wide dynamic range Gold plated output contacts True condenser externally biased Internal capsule shock mounting 149 00 Code NT1APACK Rode IXY 10S Microphone The RODE IXY is the ultimate recording microphone for iPhone iPad or iPod touch With up to 24 bit 96k recording and on board high fidelity A D conversion your IXY recordings are rich smooth and accurate At the heart of the IXY is a matched pair of 2 cardioid condenser capsules fixed in a perfect 90 degree near coincident alignment This results in immersive and true to life stereo recordings captured in incredibly high detail The IXY is supplied with a foam windshield for outdoor recording as well as a reinforced protective zip case to ensure your IXY Is available whenever you need it For more inform
15. at least it should do There are many ways in which the receiver can be Why on earth would I want to get an IR distribution connected to the distribution amplifier including dedicated amplifier cable RF aerial cable wireless radio or even an IP computer network We hope that you can use this guide to see what systems are possible and select the right products to make your own AV system easy for everyone to control With an ever increasing number of set top boxes media streamers switchers and recorders etc it is often convenient in fact sometimes essential for domestic harmony to be L erine e Panel mount seperate system Use IR oe from KIRA no o family of products via LAN or internet ez is sta ando a tie preng aaa band leptin val i ehwal mount i eperate system Use ie eperate system R re he e aah ut direct from a Use the output in are core Ne reless IR sender such direct from the widel pai Pan oie Powe au RF2IR system i A simple splitter such as the ay be used to combine two sources of IR input KA109 Code IRBKIT 3 9 z 99 Basic Kit plus Standard Receiver and High Power Wand This is a complete kit comprising the Keene IR Distribution Amplifier 240V UK mains power adaptor 1 x universal emitter wand 1 x High Power emitter wand 1 x Standard IR receiver IRSR and instruction leaflet SORUR Er IN g wan a at The main body of the IR distribution amplifier
16. each end They offer outstanding quality durability and high performance for any video signal application including HD SDI signals High quality connectors True 75 ohm BNC connectors maintain correct impedance Specifications e Conductor 18 AWG solid bare copper e Dielectric Skin Foam e Outside Jacket Color Dark gray w white lettering e Outside Jacket PVC e Shield A 61 braid aluminium wire 34 AWG e B dual foil mylar 25 overlap rate e Center Conductor 0 0403 inches 1 02mm e Dielectric 0 179 inches 4 57mm e Outside Diameter 0 391 inches 6 95mm Code SBB801 0 5M 2 73 Code SBB802 0 9M 3 12 Code SBB803 1 8M 3 90 Code SBB804 3 0M 4 68 Code SBB805 4 6M 5 45 Code SBB806 7 6M 7 79 Code SBB807 10 6M 9 74 Code SBB808 15 2M 12 47 Code SBB808 15 2M 12 47 Code SBB809 22 9M 17 14 Code SBB810 30 5M 21 82 Code SBB811 45 7M 30 39 3 BNC TO 3 BNC RGB COMPONENT CABLE High quality three BNC plugs to three BNC plugs Gold plated connections Application RGsB or component video Code SBB301 1 0M 28 59 Code SBB302 2 0M 29 99 Code SBB304 5 0M 39 99 Code SBB305 10 0M 49 99 3 PHONO TO 3 PHONO RGB COMPONENT CABLE High quality three RCA phono plugs to three RCA phono plugs Gold plated connections Application RGsB or component video Code SBB101 1 0M 29 99 Code SBB102 2 0M 34 99 Code SBB104 5 0M 39 99 Code SBB105 10 0M 49 99 This is just a tin
17. easily attaches directly to your camera s tripod mount and a SpiderPin which attaches to the Plate and slides into the Holster to give your camera freedom of Black Widow Belt Don t get us wrong the Spider Holster Black Widow Is designed to be very comfortable when worn on your own belt But our adjustable belt will make your camera feel like a feather so you can stay comfortably holstered all day long One size fits most adjustable from 23 48 inches Code BWB 1 9 99 Got two cameras rr The Spider Holster Black Widow includes one Pin but you may purchase an extra Pin for your second camera video camera or any device with a tripod mount Code BWPIN 6 7 99 Spider Pro Dual Camera System The SpiderPro Dual Camera System extends our already popular 1 Camera System giving you a comfortable and secure way to carry two cameras while on the job or on the go movement at your hip e Stainless steel and hardened aluminium durable for active shooting situations e Secure with a two position lock Code SCSS 59 00 Black Magic Intensity Extreme Incredible 10 bit HDMI and Analogue video editing with Thunderbolt Intensity Extreme the world s first 10 bit HD SD editing solution to feature lightning fast Thunderbolt technology The perfect solution for videographers Intensity Extreme includes SD HD capture and playback in compressed and uncompressed video quality Better stil
18. erratic behaviour you may have experienced from some of the other longer length cables on the market these deliver reliable results The construction features a heavy duty metal moulded connector housing with high density triple layer shielding to guard against electromagnetic interference high level OFC copper wire with 340MHz 10 2Gps ultra wide bandwidth for 1080p 3D video format and 7 1 channel audio Protective braided outer cable sheath 2aRaseee FBR B O Professional Range Flat Profile Flat cable manufactured by TTL offering high speed performance 1440P with Ethernet and Audio return channel Manufactured with gold plated contact and shell including RF Blok which protects against RF interference Lightweight flat ribbon cable which is very flexible for installation especially where there is limited space Specifications e Capable of handling up to 1440p resolutions e 3D compatable e AK x 2K ready e High quality flat cable ideal for running under carpet or through narrow spaces Code HDHDF1405 length 0 5m 10 80 Code HDHDF1415 length 1 5m 12 96 Code HDHDF1420 length 2 0m 15 14 Code HDHDF1430 length 3 0m 17 36 Specifications e HDMI 1 4v high speed Cable supporting 3D 4K ARC Audio Return Channel e 24K Gold plated connector for anti corrosive and distortion free Code HDPROAV5 5m 29 99 Code HDPROAV10 10m 59 99 Code HDPROAV15 15m 89 99 Code HDPROAV20 20m 119 99 Ultra Slim HDMI Ca
19. for public broadcasting exhibits retail stores courtrooms stock tickers bus station and many more applications Suen SE AA E Swiien e Status indicators Power green x 1 Active yellow x 1 Operating voltage 9V DC 600mA UK adaptors supplied In summary the local unit has one input and a two outputs and the a remote unit has a further two outputs Audio is duplicated in stereo x ae l PE locally and in mono on the remote unit Code EVA214 99 99 Component Video Matrix 4 2 The AVT5842Mx is a 4 input by 2 output switcher that Features and Specs can be used for either YPbPr Progressive Scan Video or e 4 Component Video Inputs via RCA connectors YCbCr Component Video plus Stereo Audio It is a dual output switcher and sends the selected input to the outputs independently Since it is a Matrix Switcher each of the two outputs can have the same or a different video signal selected from the four inputs Selection can be made by the front panel push buttons or by the IR Remote Control 4 Stereo Audio Inputs via RCA connectors e 2 Individually Selected Component Video Outputs via RCA connectors e 2 Individually Selected Stereo Audio Outputs via RCA connectors e Works with Progressive Scan YPbPr 480p 576p 720p or 1080i Component Video e R Remote or Manual Control e Video Bandwidth 300MHz e Size 1 9 High x 9 3 Wide x 5 7 Deep 48mm x 230mm x 145mm e Weight 920g e Power 12vDC 200m
20. just plug the devices in and start using them A few of the products wall switches etc do require some basic electrical DIY skills for safe installation and operation As ever if you re in doubt please consult a qualified electrician Many more X10 modules and controllers to choose from on www keene co uk X10 Transceiver Module The transceiver module catches the radio signals emitted by any X10 compatible transmitter eg KR22E SS13E etc and converts them into X10 signals for the mains wiring It simply plugs into the mains wherever you find convenient and looks very much like an appliance module with a small aerial attached The transceiver module also has an outlet socket and can be used like an appliance module although Its address e code cannot be altered from address i code 1 It has an effective reception range of around 30 metres so normally one centrally located transceiver module is enough to ensure that an X10 remote will work more or less anywhere within the house 19 85 Code TM13U X10 Internet Control Use your smartphone or tablet to operate your X10 devices The TIP1ORF connects directly to your network router and sends commands wirelessly to the nearest transceiver e g TM13U No need to leave your computer turned on Download the free Android app from the Play Store IOS app to follow shortly 53 95 Code TIP10RF Email your order to us at sales keene co uk AV Plat
21. mains to USB power supply Choose this option if you have have a nearby spare USB port that can provide power Code IRBKITMFC 58 19 IRBKITMF Code IRPKIT4 6 1 z 7 4 Code IRPKIT4S2 8 7 x 0 1 IRPRO4 with Fascia Mount IRPRO4 with Panel Mount Receiver Receiver IRPKIT4F2 is the Basic kit plus a Fascia Mount IR j IRPKIT4B2 Is the Basic kit plus a Panel Mount IR receiver and two universal IR emitter wands receiver black and two universal IR emitter wands r IRBKIT Mini with Direct Cable Input IRBKIT Mini supplied with 2 x IRDW Dual Blinking Wands four emitters and a direct input cable no receiver This is designed to re distribute the IR Blaster output from another device eg HDMI extender Supplied complete with a mains to USB power supply 9 9 63 71 Code IRBKITMD Also available without the mains to USB power Supply Choose inisoptionrll You Nave naea nealby Code IRPKIT4F2 87 x 50 Code IRPKIT4B2 99 a 1 7 spare USB port that can provide power Code IRBKITMDC 54 41 Find product information and data sheets on www keene co uk IR Distribution IR Universal Wand The Universal wand is ideal for most applications and can be mounted directly onto the equipment fascia or placed on the shelf in front Dimensions of emitter L21mm xW 19mm x D 7mm Fitted with a 1 2 metre cable e599 IR Single Blinking Wand This is a small discrete emitter that can be mounted directly o
22. no user intervention required Specifications e Input Video Signal 0 5 1 0 volts p p _e Video Amplifier Bandwidth 1 65Gpbs 165MHz e Output Video HDMI 1 2a e Video format supported e DIV HDTV 480i 5761 480p 576p 720p 1080i 1080P e Transmission distance e CAT 6 cable 50M for1080p e Operating Frequency e Resolutions HDTV e Vertical Frequency Range 50 60Hz e Interlaced 50 amp 60Hz 480i 576i1 1080 e Progressive 50 amp 60Hz 480p 576p 720p 1080p Please note in order to achieve the quoted transmission distances please use only CAT 5e or CAT 6 cable HDMI Signal Repeater 1080p Value Range Use one of these to join two HDMI cables and extend the maximum cable distance The repeater contains circuitry to regenerate the HDMI signal and extend the effective cable length while maintaining all signal components present within the encoded signal including stereo or 5 1 audio and HDCP encryption Multiple devices can also be daisy chained as required up to any cable length Specifications e Extends high definition video and digital audio using a single box solution e Up to 30m Max cable length also cascadable e HDMI Amplifier Bandwith 1 65GHz e Dimensions 5 x 2 8 x 1 8cm e HDMI V1 3 compliant e Power DC 5v 170mA max In most cases the repeater is able to use the power from the appliance and no external power adaptor is required Code HDMIRV 1 4 99 Gigavideo 821 Wireless HDMI Sender At last
23. of sending HDMI over long distances whilst preserving the full HD capability The transmitter converts the HDMI signal into a balanced differential signal and the receiver converts it back into a conventional HDMI signal again It uses two runs of CAT5E or CAT6 cable and allows for full auto adjustment of feedback and equalisation with no user intervention required Long HDMI cables are expensive and unwieldy whereas CAT5E cable is cheap and flexible making it much more suitable for long distance runs The HDMIC50 can send HDMI at full 1080p up to 50m up to 100m at 480p They can also be used for DVI D signals with a suitable adaptor such as the KA169 The HDMIC530 is rated at 1080p at 30m and 480p at 60m Code HDMIC530 39 99 Code HDMIC550 59 99 HDMI over Single CAT5 Specifications e Input Video Signal 0 5 1 0 volts p p e Input DDC Signal 5 volts p p TTL e Maximum Single Link Range 1920X1200 1080P e Output Video HDMI 1 3 e Video format supported DTV HDTV 1080P 1080i 720P 576P 480P 57 61 4801 e Size 45 x 25x 81mm e Power Consumption 5W max e Operating Temperature 0 to 70 C e External Power Supply 5V DC 2A e HDMI V1 3 compliant 50M System Some HDMI over CAT5 transmitters require two runs of CAT5 cable This new item can do the same job with a single run of CAT5 cable great for adapting existing installations The modules are plug and play with full auto adjustment of feedback and equalisation and
24. or S video connections but doesn t allow the use of both simultaneously Code STOC 9 a 99 VGA in to HDMI Out The Coosis VGA to HDMI Portable convertor is designed to be extremely compact in size and ideal for home and office use or life on the move Users can plug this convertor into their desktop laptop or any device with a VGA output must be an RGBHV type signal not component or YUV and convert easily to HDMI Great for watching PC and laptop signals on your big screen TV or getting your presentation on to the office projector The best thing is that resolutions of less than 1920 x 1200 60Hz don t need any extra power although a USB power cable is included should you wish to use 1920 x 1200 60Hz An analogue audio input is included as a 3 5mm stereo socket and this is then output in the HDMI signal to the display Please be aware that this is only a signal convertor and not a scaler The output resolution will be the same as the input resolution and will not increase the picture quality Code VGAHDMIP 49 a 99 HDMI to Composite amp S Video Down Convertor VS 226 HDMI to CV SV Stereo Down convertor changes digital HDMI signals or a DVI input signal with S PDIF coaxial audio to NTSC or PAL analogue video signals and also provides a L R stereo audio output Besides S Video and Composite Video outputs it provides a re clocked HDMI signal which delivers a jitter free bypassed output of the original HDMI s
25. or the world s most popular editing software such as Final Cut Pro and Premiere Pro Code BINTSTBEXT 2 24 00 Find product information and data sheets on www keene co uk E A small selection from the AV accessories on www keene co uk S Internet Controllable Mains Switch New from Keene the IPMSW1 is an IP controllable mains power switch It has two independent mains outlets that can be controlled in a number of ways Features e Simple browser button based on off control e Full browser based set up and timer configuration e Adjustable power fail re start options allow each switch to delay up to 255 seconds before switching on Ideal for remote re start of systems that require 2 stage start ups e 3 timer events per switch with daily weekly or monthly repeats e During each timer event the switch can be set to either on or off e Own IP address so can be controlled via internet using port forwarding e Support for DDNS e Manual override button for each switch e Optionally use internet time servers to set internal clock e Internal Real Time Clock IC with 5 year battery backup Mighty Brighty Projector Screen Paint amp Border Mighty Brighty turns a wall into a projection screen Mighty Brighty is a new and unique concept for creating a perfect projection screen right on your wall or any other smooth surface Just paint it on sit back and enjoy An image projected on Mighty Brighty Projec
26. prevent unwanted IR cross talk Can be used with all Keene and most other manufacturers IR Emitters Improves IR Signal to noise ratio Prevents IR signals from interfering with other equipment Overall dimensions 37mm x 29mm Internal space for emitter 27mm x 14mm widest x 7 5mm deepest Single IR Shield 63 49 Code IRSHIELD s re oS S3 Pack of Four IR Shields 69 99 Code IRSHIELD4 Pack of Ten IR Shields Code IRSHIELD10 1 9 2 99 Fascia Mount IR Receiver This IR receiver is designed to be affixed directly to the fascia on your display Super fast electronics and a semi wideband capability make It really effective to use whilst it s compact size makes it very unobtrusive The LED provides visual confirmation that the signal has been received Typical IR receivers require a minimum of 10 cycles before they can lock onto the signal This receiver will work with just 3 or 4 cycles This fast circuitry enables it to work with set top boxes that use very short bursts of IR code known as RCMM code as used for example by some BT Vision set top boxes Code IRFMR 1 4 99 Standard IR Receiver Standard IR Receiver 40kHz suitable for most domestic AV equipment Code IRSR 1 2 99 Wideband IR Receiver Wide Band IR Receiver Up to 100kHz for more esoteric equipment Code IRWBR 1 8 99 Wall Plate IR Receiver IRSR built into a single gang pattress with tra
27. ray Player satellite receiver and all other HDMI devices e Full HD 1080p e Switches automatically and or with remote control e With separate IR receiver for operating the switcher when it is placed out of sight Code C310 29 95 HDMI Switchboxes Value Range Compact low cost HDMI switchboxes offering excellent value for money Auto source selection plus IR for SW103 Features e Easily switch between HDMI sources e Full HD 1080p supported e Compatible with HDMI 1 3b and HDCP Note not suitable for DVI devices no control signal for auto switching 24 99 29 99 Code SW102 Code SW103 two inputs to one output three inputs to one output AAVARA 4 1 Switchbox The Aavara SW421 provides easy switching from any of four HDMI inputs to 1 HDMI output Featuring CEC Consumer Electronic Control Pass through for fast switching this Is a very effective and economical solution Features e Allows access from four HDMI devices to 1 HDMI display e CEC Consumer Electronic Control pass thru Output Channel 1 e Support 36 bit Deep Color up to 1080p e Support x v YCC wide color gamut e Audio support Dolby TrueHD amp DTS HD e Support 7 1 digital surround amp Lip Sync e HDMI firmware upgradable e Plug and play Installs in seconds e Dimension 245 W x 107 D x 27 H mm e Package Content 1080p HDMI Switcher 4 1 Remote Control 9V DC Adapter Usermanual Code Sw421 49 99 HDMI 3 2 Swi
28. signal uncompressed Please note that although this wireless kit is capable of transmitting a full HD signal through walls and ceilings it does greatly reduce the tranmission distance As a general rule a clear line of sight transmission is easily achieved up to 20 metres but this can be effected by local sources of interference from mains points wireless routers etc although a little time re positioning the transmitter and receiver units can usually get around the problem For transmissions where the signal is passing through a wall or ceiling please be mindful of the make up of the wall or ceiling Naturally a signal will pass much easier through plaster board and dry walling than it will a steel reinforced concrete structure or stone walls and this will effect the signals transmission greatly It is also worth noting that if you wish to send a signal through more than one wall or ceiling the transmission distance will be reduced further still and careful consideration needs to be given to where the units will by positioned If you would like any information or advice to assist you please don t hesitate to get in touch and we will do our best to help We can also offer a solution with a shorter transmission range ideal for same room applications GV811 Code HDEX344 299 a 00 HDMI extender over CAT5 with IR control This product makes a very affordable method of sending HDMI over long distances whilst preserving
29. to it e Frequency response 70Hz 20kHz e Power 25W 25W RMS e Overall Dimensions 227x86mm e Cut Out Dimensions 193mm e Impedance 2 x 8 Ohms Code CMS65S single speaker 29 99 Moisture Resistant Speakers for use in Walls or Ceilings High quality moisture resistant speakers suitable for PA installations in swimming pools bathrooms shower rooms saunas and tanning rooms etc 148mm Circular CMSSMR e Frequency response 80Hz 20kHz e Power 35W RMS e Overall Diameter 148mm e Panel cut out 112mm w E e P35 rated 180mm Circular CMS8MR e Frequency response 80Hz 20kHz e Power 40W RMS e Overall Diameter 180mm e Panel cut out 132mm e P35 rated Code CMS5MR per pair 34 99 Code CMS8MR per pair 39 99 254mm Square B414C e Frequency response 40Hz 20kHz e Power 90W RMS e Overall Dimensions 254x254x87mm e Cut Out Dimensions 219x219mm Moisture Resistant Design Subwoofer B403A e Frequency response 30Hz 4kHz e Power 220W max e Overall Diameter 268mm e Panel cut out 232mm x 177mm deep e Impedance 8 Ohms 6 e Moisture Resistant Design 39 99 27 99 Code B414C Code B403A aS eee A PACKAGE DEAL Amplifier kit with Speakers Special Offer per pair single speaker KLABKITD plus a pair of CMS5U Code KLAB20DC5 KLABKITD plus a pair of CMS8U Code KLAB20DC8 189 99 229 99 Digital In Wall Slave Amplifier
30. ually located out of sight or les the AV c cabinet Eis operates tom 125 eee allowing The R Universal wand is for n low powe r alae ut and can ir P in eo cen i m manne vel installati Bis be mou iad die ctly on the e eal ee or positioned on Y OCR OTS el the shelf There is one output for drivi rg wands to high power High power wands can be used to control equipment located op io 1 Gin away o ptional A aim renean nge emitter for direct attachment to the equipment fas o epii enal ess very directional eh poxa ee range emitter for e the IR RUW hos suffici Asi vE le jack plug drives a pai ore that affix directly to i a imen fascia and a a visible flash as the IR signal is emitted A r Basic Kit plus Fascia Mount Basic Kit plus Receiver Panel Mount Receiver Complete in cabinet IR Distribution solution with 2 x This is a complete kit comprising the Keene IR Distribution Universal Wands and a Fascia Mount IR receiver Amplifier 240V UK mains power adaptor 2 x universal emitter wands see output component IRUW page 28 1 x Panel Mount IR receiver and instruction leaflet Code IRBKITSH 49 E 99 Basic Kit Plus Standard Receiver This is a complete kit comprising the Keene IR Distribution Amplifier 240V UK mains power adaptor 2 x universal emitter wands IRUW 1 x Standard IR receiver IRSR and instruction leaflet HINT This is far and away our most popular kit so if you re wondering where to start t
31. use in room 10m range with clear line of sight Single HDMI input amp without IR feedback See www keene co uk for full specification Code GV811 249 99 Find product information and data sheets on www keene co uk HDMI Over Long Distances HDBaseT HDMI extender System This is quite a product The Aavara PE3D4K100A Is a another fantastic tool for installers Using just a single wire it can be easily retrofitted within an existing network HDBaseT technology allows this system to send HDMI further and at higher quality than all other conventional HDMI over CAT5 solutions With no compression and no loss of quality you can get crystal clear 3D 1080P with 7 1channel audio and also have IR control RS232 and extend your 100Mbps LAN all over the one cable Over one single run of CAT5 cable you can e send uncompressed full HD 3D HDMI with 7 1ch audio e remotely power the receiver e IR control the source from the receiver e RS232 control the source from the receiver e use the 3 port hub in the sender amp receiver to extend your LAN It also fully supports HDMI v1 4 allowing smooth 3D video transmission from 3D Blu ray players to 3DTVs with fully HDCP compliance Built in 3 x 100Mbps Fast Ethernet RJ 45 ports at both sender and receiver provides internet connection for TV Video device and PC Power Over Cat5 Cable design makes Receiver side powered directly without extra power adapter to Receiver unit Convenient IR Pas
32. www keene co uk for details Code LAVALIER 1 59 00 Find product information and data sheets on www keene co uk D SLR LCD Viewfinder for DSLR HD Video The DSLR LCD Viewfinder is a great accessory for anyone using a DSLR to shoot video It solves the 3 major problems 1 The necessity to view images continuously on the LCD screen which in turn effects stability and thus focus where the camera has to be handheld away from the body 2 The inability to actually see any image on that same screen when working in any bright lighting conditions 3 Trying to ascertain the depth of field even if you can discern that image The DSLR LCD Viewfinder solves these problems by providing a finder that gives you a nice large 3 inch LCD image to work with and then adds a 3x magnification for extra clarity What s more it features quality optics consisting of three elements arranged in 3 groups Clipping onto the rear of your DSLR finder it provides the perfect environment for comfortable viewing incorporating as it does a soft motion picture type moulded eyecup to block out extraneous light thus letting you view a perfect image It also offers an excellent range of continuous dioptre variations between 4 and 4 to accommodate glass wearers The combination of these features allows you to bring the camera In close to your body for increased stability and secure viewing and filming LED Light Ring and Flash unit New
33. www keene electronics co uk for full details The IR inputs and outputs are fully compatible with the existing Keene IR Distribution range so other styles of receivers and emitter wands can easily be incorporated e Control IR equipment via local network or anywhere in the world via internet e Can be combined with IR distribution system for large installations e One to one or many to one control Product code IR over IP Browser Control Memory RS232 Routable Outputs PoE KIRA128 yes Ka yes yes 2 KIRA Modules These modules will receive an IR command convert it to packet data and send that data to a predetermined IP address usually another IR Anywhere module The receiving module will then decode the data and re transmit the IR as originally received The IR Anywhere modules are physically identical and can be software configured as either a receiver a target or stand alone operation They will operate via LAN and also via WAN assuming firewall and routers are correctly configured They are supplied either singly or as a pair of modules Once correctly configured one target can receive signals from multiple receivers The target can be either an IR Anywhere module or the IR Commander Matrix e Control IR equipment via local network or anywhere in the world via internet e Can be combined with IR distribution system for large installations e One to one or many to one control e Built in Dynamic DNS support e DHCP plug
34. 080p plus 1080p24fps This requires a Distribution Amplifier something that takes withthe included R Racaver a Blaster e High Definition Audio supported Dolby TrueHD Dolby one signal in and gives you multiple identical signals out l Digital Plus and DTS HD Master Audio plus LPCM You would use one of these where you d like one source to e Compatible with CAT 5E and CAT 6 cables CAT 6 is be sent to multiple displays recommended for better performance People also sometimes call these splitters as you are in Supports CEC functions amp IR blaster affect splitting one signal into many Splitters are more l _ usually used to refer to analogue audio and video devices e Supports Deep Colour 10 amp 12 bit Transmission as these can be split passively in a crude fashion without distances may be reduced at higher colour depths any electronics A distribution amplifier contains circuitry to e Equalises and recovers incoming TMDS data before re buffer the signal and ensure that each output is the same transmitting to ensure optimum signal quality as the input Even if you wanted to you cannot passively F c2 08 43 T split an HDMI signal because it is digital so the correct Code i i pp terminology is a Distribution Amplifier I want to go from a scart to HDMI HDMI over CAT5E 5 Multiroom Features That s no problem but because you are converting an Distributi Syst S E E E T analogue signal Scart to a digital one HDMI you
35. 10mm 16 1 VESA Compatibility 300 x 200 300 x 300 400 x 200 400 x 400 600 x 400 integrated cable management Product dimensions Height 1910mm 75 2 Width 1000mm 39 4 Depth 500mm 19 7 including wheel castors 10mm 0 4 tempered piano black safety glass base BS6206 Graphite Black finish Max Weight 70kg 154lbs Max Dist between Fixings H 280mm 755mm V 410mm 389 99 LCD Wall Mount with tilt amp swivel up to 42 e Designed for screens up to 42 107cm 25kg 55lbs e Full motion mount Code BT8505B black ideal for corner mounting e Fits screens with VESA mounting patterns 75mm x 75mm 100mm x 100mm 200mm x 100mm and 200mm x 200mm e Easy tilt adjustment 40 e Features three swivel points 180 at wall 360 central pivot and 240 interface e CLIPLOGIC cable management included e Simple hook on installation with all mounting hardware included e Screen size 15 42 e Max Weight 25kg 55lbs e Security locking screws and Allen key provided for secure installation e Features OWLS On Wall Levelling System Colour Black l 54 84 Stealth Onyx Speakers Stands e Stealth Onyx AV Speaker Stands with Glass Base e Designed for home cinema speakers up to 2kg 4 4lbs Adjustable height 685mm 27 1060mm 42 e Includes adaptors for single point dual point and keyhole fixing e Suitable for speakers using M5 M6 and UNC
36. 14 99 Brush Opening 2U Code PP10 24 99 Choose from a huge range of Switchcraft chassis mount AV sockets and couplers on www keene co uk Find product information and data sheets on www keene co uk IR Distribution Systems IRBKIT IR Signals Explained The classic in cabinet solution that puts your remote back in control and routes IR commands to wherever they are think we are all aware that infrared is just light that we able to locate much of the equipment in a small room or needed This unit can be expanded to provide a solution cannot normally see It is light at the low red end of the cupboard out of sight Unless you want to get up and go to almost any IR control problem Multiple input output visible spectrum and shares many of the properties of to the cupboard room loft or wherever every time you visible light Like visible light infrared travels in straight lines want to change the channel or volume you will ideally need apuans Ar available and you can add extra aa and and will not go around a corner unless there is something some means of controlling all this equipment from your emitters as required see p28 29 for more details It is about that will reflect it or refract it Also like visible light it armchair This is where an IR distribution system comes in available ready to use in a number of configurations is reflected by white surfaces and usually absorbed by dark An IR distribution system is basically expe
37. 6A e The relays can be set to open close or pulse with configurable timings Both relays feature pluggable Phoenix connectors for easy installation IR Commander Matrix The most advanced and the most capable IR distribution system we ve ever produced e Full Matrix Signal Routing Each IR input can be routed to any combination of IR outputs This means for example an equipment cabinet could house say three identical Sky receivers and each one can be controlled independently from different rooms Four IR output channels each IR output channel can drive IR emitter wands or slave IR distribution amplifiers Six local IR input channels Four IR receivers one on board IR receiver and one wand input for taking the output directly from another IR distribution system or video sender IP addressable Will accept IR over IP inputs from Keene IR Anywhere modules or from PC s or handheld devices up to 253 different IP addresses Internal IR command store Can store up to 64 IR codes in local memory these can then be triggered by IP command from local network or internet e Network inputs can be routed based on IP address Maximum flexibility for LAN devices Built in wideband IR receiver May be disabled if required Local inputs are one way IRDA compatible Will route signals to control all popular set top boxes Will act as Dynamic DNS update client Built in support for non static WAN IP addresses e LEDs
38. A UK adaptor included Code AVT5842MX 1 6 2 x 3 8 Find product information and data sheets on www keene co uk RGB Conversion amp Distribution Keene RGB2C RGB Component video transcoder Another in house product from Keene Electronics the RGB2C can convert an RGB input to a component Y Pb Pr output and vice versa It can cater for sync on green or composite sync input and also provide sync on green or composite sync output LED indicators provide useful information on the type of signals present and which process is being performed Designed to be installed in line with the signal path has SCART input and output connectors to make connection simple Supplied complete with UK mains adaptor and KA150 scart to 3 phono adaptor BULK PRICING 50 available HDMI input to Component or RGBHV amp Audio output This unit will take in HDMI and give out either Component video Y Pb Pr or RGBHV PC signal plus spdif or analogue stereo audio It enables you to connect your new HDMI sources to older analogue displays The convertor is extremely compact in size and can be plugged directly into a display with VGA connections or use the supplied cable to connect to a Ypbpr component video Specifications e Video Input HDMI connector e Compliant with HDMI 1 3 and HDCP 1 2 e Output Analogue HD 15 RGBHV YPbPr e Operation frequency up to 165MHz Resolution RGBHV up to UXGA 60Hz Component up to 1080 n
39. Analogue models are built into a metal two gang Thelen ion sd Code KLAB20 Amplifier amp Remote 87 00 o a ee W i aa i f ect Code KLABKIT Amplifier PSU amp Remote 111 00 nee agence cee sean wate Code KLABPSU 15v DC 4A power supply 29 99 remote control The Keene KLAB can be purchased with either a Features white or a translucent frosted style front panel e 20 RMS per channel output e Rear line level audio input Code KLAB20F Amplifier amp Remote frosted 87 00 e Infra Red remote control Code KLABKITF Amp PSU amp Remote frosted 111 00 Code KLABPSU 15v DC 4A power supply 29 99 KLAB Digital Models The Digital models Class D Amplifiers for maximum efficiency This design allows the PCB to be mounted directly onto the front panel rather than built into the pattress as with the analogue version In addition to the Code KLAB20D Amp amp Remote grey 125 99 rear line level input this model also incorporates a front Code KLABKITD Amp PSU amp Remote grey 149 99 jack socket audio input and built in FM radio with a Code KLABPSU 15v DC 4A power supply 29 99 ten channel memory The Keene KLAB20D can be purchased with either a Features grey or white fascia surround e 20 RMS per channel output Code KLAB20DW Amp amp Remote white 125 99 e Class D digital circuitry Code KLABKITDW Amp PSU amp Remote white 149 99 e Built in FM Radio Code KLABPSU 15v DC 4A power supply 29 99 e Front 3 5mm input jac
40. Ax 1 x YR Stereo Line Level output Speaker Terminals e Control via remote control RS 232 or IP Web GUI or Telnet e Dedicated Microphone input for commercial application e Supports Digital to Analogue DAC and Analogue to Digital ADC conversion e Simultaneous audio outputs e Compact design for remote application Specifications Inputs 2x HDMI 2x HDMI Uncompressed AV and Data 1x XLR 1x Microphone 1x Toslink 1x Optical 2 Channel LPCM 1x RCA 1x Coaxial 2 Channel LPCM 2x RCA 1x Analogue Stereo L R 1x 3 5mm Stereo mini jack 1x Analogue Stereo L R 1x RJ45 1x IP Control 1x 3 5mm Stereo mini jack 1x Infra Red Receiver 1x 9pin Dsub 1x RS 232 Data Outputs 1x HDMI 1x HDMI Uncompressed AV and Data 1x Toslink 1x Optical 2 Channel LPCM 1x RCA 1x Coaxial 2 Channel LPCM 2x RCA 1x Analogue Stereo L R 4x Speaker Binding Posts 1x Speaker Level Stereo Output PSU 24V 4 16A Dimensions 255mm W x 170mm D x 48mm H Code AUA300 3 9 5 2 03 HDMI Audio Amplifier with HDBaseT All the features of the AUA300 above with the added benefit of integrated HDBaseT input and output This means It can be used for creating additional HDBaseT zones or used to repeat the signal to further HDBaseT 2 Channel Digital AV Receivers Goer 574 61 Code AUA300HBT HDMI Scaler Audio Cross Convertor 1T VS 658 Video Scaler is a professional Up and Cross Convertor with an HDMI ou
41. Code HDHD142S 2m version 19 99 Code HDHD143S 3m version 24 99 Specifications e Works with PS3 XBOX Blu Ray HD DVD player Set Top Box e 1 2Gbps Ultra Wide bandwidth enable brilliant 1080p HD content and 8 channel Audio e Exclusively Superior Diamond cutting design and stylish yellow webbing lines e HDMI to DVI interoperability allows easy interconnectivity e Support Dolby True HD and DTS HD Master Audio Transmission e Support x v Colour Wide Gamut and 16bit Deep Colour Video Transmission Code HDAV05 0 5m version 14 99 Code HDAV1 1m version 17 99 Code HDAV2 2m version 12 99 Code HDAV3 3m version 24 99 Bend to shape HDMI cables From CYP these Neat amp Tidy cables provide genuine innovation for the custom installer The reinforced structure allows them to be manipulated into a desired shape which will be retained for the duration of an install This new design allows installers the make tidiest of finishing touches to an AV installation while also optimising the connection between sources in a rack Specifications e Full 1080p and deep colour resolutions e 3D Compatible e 99 999 Oxygen Free Copper Code HDMI030 30cm version 10 67 Code HDMIO50 50cm version 11 45 Code HDMIO75 75cm version 12 43 Aavara Hi Definition Pro Install HDMI Cables These are top specification Hi Definition AV Cables designed for Professional and Commercial installations Designed to end the uncertainty and
42. D Display Integrated 2 1A USB charger Detects amp charges most USB devices iPad amp iPhone Samsung Note Tab all Samsung Smartphones Includes an AA battery tray for charging of an additional 4 x AA Supplied with interchangeable UK Euro and US plugs 12V Car Lead included The SEAGULL DSLR LCD FINDER is an essential tool for any serious film maker Without It that grouping of a small LCD screen manual focus razor thin shallow depth of field camera shake sunlight and glare makes shooting a video an hit and miss affair with it the control is all yours Specifications Magnification 3x Optic Glass 3E3G Dimensions 84 5 x 70 x 77mm Diopter 4 Will fit LCD Size up to 3 Inch Comes complete with hand strap Code LCDVF 7 4 9 9 Specifications LED light Power output 5w Colour temperature 5800k Brightness 480 lumens Flash Index 8 5ft ISO100 1 60s Powered by 4pcs AA batteries not included Code MRC80 7 9 a 99 Compatible with the Canon E6 amp HL E6 E8 amp HL E8 series and the Nikon EL14 amp HL EL14 EL15 amp HL EL15 series batteries Code PROCUBE 57 5 88 LED Light Panels LED126T The light head carries 126 super bright LED bulbs to give plenty of illumination These are controled by the on board on off slider switch and a rotary dimmer gives you control over the amount of light to be used Rather than use the traditional choi
43. M 79 99 PFS4 FLAT SILVER 1 22M 19 99 PFS8 FLAT SILVER 2 44M 23 99 PFS16 FLAT SILVER 4 88M 40 99 PFS25 FLAT SILVER 7 62M 51 99 PFS35 FLAT SILVER 10 67 55 99 PFS40 FLAT SILVER 12 2M 70 99 PFS50 FLAT SILVER 15 2M 79 99 PRG4 ROUND GOLD 1 22M 18 99 PRG8 ROUND GOLD 2 44M 2299 PRG16 ROUND GOLD 4 88M 38 99 PRG25 ROUND GOLD 7 62M 48 99 PRG35 ROUND GOLD 10 67M 56 99 PRG40 ROUND GOLD 12 2M 67 99 PRG5O ROUND GOLD 15 2M 76 99 PRS4 ROUND SILVER 1 22M 18 99 PRS8 ROUND SILVER 2 44M 2299 PRS16 ROUND SILVER 4 88M 38 99 PRS25 ROUND SILVER 7 62M 48 99 PRS35 ROUND SILVER 10 67M 56 99 PRS40 ROUND SILVER 12 2M 67 99 PRS50 ROUND SILVER 15 2M 76 99 HDMI to DVI Cables HDMI plug to DVI plug 1080p rated i S Code HDDV2 length 2 0m 7 99 Code HDDV3 length 3 0m 12 99 Code HDDV5 length 5 0m 14 99 Code HDDV10 length 10 0m 19 99 HDMI Extension Cables HDMI plug to HDMI socket extension cable High Speed Code HDHDE2 length 2 0m 9 99 Code HDHDE3 length 3 0m 11 99 Code HDHDE5 length 5 0m 14 99 Code HDHDE10 length 10 0m 24 99 HDMI Outlet Plates From Keene a wall plate with an HDMI socket at the front and a PCB mounted rear socket The rear socket is aligned such that a side entry HDMI cable should pass through one of the side knock outs in a std metal rear pattress Depending on the size of plug used some modification to the pattress may be necessary We can supply this item as follows
44. R control from any remote TV that is connected by aerial cable to the source equipment Other options are available RF2IRL If you already own Female Male Male socket to 2 x plugs an IRBKIT distribution system you could save a little and share the power supply If you would like an IRBKIT distribution system as well you can also save some money by buying the two together To use simply connect the eye receiver in line with the TV aerial on the remote TV and the RF2IR in line with the aerial at the source IR signals picked up by the eye receiver will be relayed along the aerial cable decoded te fF by the RF2IR and output to an emitter wand to control ef G the source equipment The output from the RF2IR can M also be fed into an IR distribution amplifier such as the h IRBKIT to control multiple items inside a cabinet Code RF2IR 44 99 Code KA121DC 4 99 Code RF2IRL 39 99 Also available as Male Female Female Code RF2KIT with IRBKIT distribution system 69 00 code KA121DCF 5 99 Eye Routing Commander Analogue RF Modulator Achieve independent control of multiple SKY Receivers The Keene wideband modulator enables a camcorder Specifications within the same cabinet security camera DVD VCR or any other device with AV s Power TADE 150mA BE rae audio video output to be connected to the aerial r The KERC is a sophisticated IR Control Distribution socket of a TV It can be left permanently connected e Modu
45. Receivers are available POWERMID RF Receiver IR Transmitter unit This unit receives the RF signal from a Powermid transmitter and gives out Infra Red Code PMIDR 18 99 POWERMID IR Receiver RF Transmitter unit This unit receives IR from your remote control and gives out the RF signal to send to a Powermid receiver Code PMIDT 18 99 POWERMID Dual Output Wand Additional 2 way IR wand for use with the Powermid units These wands are designed to take the IR output direct to the IR receiving eye on your DVD etc Universal IR Extender Cable Works with Marmitek Speakercraft etc 2 IR LED s blinking 3m cable length 3 5 mm jackplug 8 99 Code PMIDEYE POWERMID 300 Xtra The Powermid 300X is another wireless IR extender system For this one the receiver can be powered by 2 AAA batteries with surprisingly long battery life or via USB if you have a spare USB port on your display or STB A mains to USB power adaptor is also included just in case Transmitter amp receiver pair Code PMID300X 35 95 Additional IR Receiver nae c2 3 7 9 5 Additional IR Transmitter 23 95 Code PMID300XT Email your order to us at sales keene co uk unm 29430 MARMITEK Easy Icon Universal Remote Control A very clever universal remote from Marmitek It can control X10 equipment via RF and up to 10 AV devices by infra red control It features assignable icons for favourite channels making It very easy to use
46. a cable free solution for HDMI The transmitter has two HDMI inputs and includes a local HDMI pass through output so you can still view the sources locally Switch between any of the two inputs and watch the output cable free at a distance of up to 30m clear line of sight or typically 15m through walls The signal is uncompressed so the output will stay as true HD up to and including 1080p Naturally there s built in IR feedback so you can control the source from the viewing area Features e Replace your HDMI cable wirelessly and locate your HDTV or projector wherever you want e Mount the receiver out of sight behind your HDTV or on the ceiling next to your projector No more visible cables e Watch up to 2 HD devices such as Blu ray players digital video recorders DVRs HD set top boxes PS3 or Xbox game consoles or standard DVD players recorders elsewhere in your home and easily switch between the sources connected without changing plugs e The built in HDMI splitter means that you can also connect an HDTV to the Transmitter so that you can continue to watch the connected devices locally e Operate your A V sources from anywhere even through a wall or cupboard door using the IR receiver e The HD signal does not experience any delays and is therefore perfect for game consoles e Digitally supports all 480p 720p 10801 and 1080p Full HD resolutions from up to 30 metres e 100 HDCP compliant Sends the HD
47. able an SDI to HDMI Convertor Code CONVMSH 219 26 HD UltraBridge A powerful multi format HD video switcher the UltraBridge has e 1 X Component YPbPr video and audio inputs 480i p 576i p 720p 1080i p 60HZ 50HZz e 1 X VGA video input and stereo audio input up to 1920 X 1200 60Hz e 1 X S video video input and L R audio input e 1 X Composite video input and L R audio input e 2X HDMI input supports 4801 p 576i p 720p 1080i and 1080p at 50 60Hz e 1 X USB 2 0 input supports to read contents of hard disk or flash drive and files will read mpeg 1 2 4 rm rmvb mov jpeg bmp png wma mp3 All inputs can be switched to 1 scaleable HDMI output at up to 1080P Code UBRIDGE 274 99 HDMI Cross Convertor This HDMI Scaler can accept audio embedded in the incoming HDMI signal or from the separate Toslink or analog Stereo inputs The HDMI output can be the same resolution or scaled to a different resolution Output audio is simultaneously present embedded in the HDMI signal and separately as Toslink and analog Stereo This provides maximum flexibility for systems integration The unit is ideal for situations where the HDMI source resolution and or frame rate is incompatible with the display device s resolution frame rate A comprehensive OSD menu and buttons allows selection of output resolution adjustments of picture quality and audio source selection It s also possible to add up to 150ms of audio delay to com
48. ade output in Receiver for great extension flexibility e Support 5 layers Cascadable for up to 600M 1080p video transmission and up to 10 TVs Displays Projectors connected e BNC connector designed for solid coaxial connection e HDMI v1 3b HDCP Compliant e Hassle free plug n play install in seconds HDMI Analyser The XA 1 is the perfect analysis tool for AV installers and integrators This device allows the user to analyse AV sources for resolution and EDID information whilst also providing pattern generation and test functions for identifying display capabilities This small but advanced HDMI analyser also supports the analysis and pattern generation of 3D signals This allows the user to check compatibility between sources and displays and provides a means of identifying system problems for troubleshooting Features e Supports v1 4 HDMI Audio Return Channel ARC function e Support timings include SD HD up to 1080p PC up to WUXGA and 3D e Analyse input source info frame and output sink EDID e Deep color video support up to 12 bits e HD resolutions supported 480i to 1080p 1080p24fps e PC resolutions supported VGA to SXGA WUXGA e 3D modes supported Frame Packing 720p 50 60 1080p 24 Side by Side half 1080p 24 60 720p 50 60 Top and Bottom 1080p 24 60 720p 50 60 e Provides 25 timings and 6 patterns e OLED show Input Output timing information e Support input signal bypass digital video formats i
49. air twisted cable 24AWG non plenum horizontal ip solid conductor Beige sheath metre marked with rip cord 305m pack only ANSI EIA TIA 568 A 5 ISO IEC 11801 BS EN 50173 UL444 UL1581 UL 1666 approved Order loose by the metre or by the 305m pack Code KBL23 1 10m 0 49 m 10 m 0 40 m 305m reel 109 80 0 36 m UTP CAT6 Cable Unshielded 4 pair twisted cable 24AWG non plenum horizontal solid conductor Flame retardent grey sheath with rip cord 305m pack only Order code KBL33 loose by the metre or 305m pack in easy pull box T ae Code KBL33 1 10m 0 78 m Code KBL33 10 m 0 68 m Code KBL33 305m reel 173 85 0 57 m Couplers amp Connectors CAT5E coupler back to back RJ45 sockets Code C5EC 1 99 Code C5EC buy 5 7 50 Code C5EC buy 10 12 50 RJ45 clear plastic crimp on end connector suitable for KBL23xx cable Code RJ45C CATS 0 49 Code CAT6C crimp on connector CAT6 rated for KBL33 0 99 RJ45 crimp tool for easy fixing of RJ45 end connectors 9 99 Code RJ45T CAT5 Outlet Components RJ45 fascia plate for network connections containing IDC connections for UTP cable suitable cable KBL23 KBL33 A clip in ID plate allows for easy labelling Single port version Code UTPSP 5 99 Twin port version pictured Code UTPTP 7 99 Surface mount pattress box 25mm deep for use with CAT5 fascia plates Code UTPP 2 99 Pattress box 45mm deep has breako
50. al options for integration of third party control systems CYP provide control drivers for control systems such as Control 4 RTI Crestron AMX Control FX and Demopad These are available at no extra cost Code PU44XLKIT 1 7 68 a 7 1 Features e v1 3 HDMI HDCP 1 1 DVI 1 0 compliant e v1 3 HDMI over single CAT6 transmitter and receiver set e Resolution supported HDTV 480i to 1080p including 1080p24fps e High Definition Audio supported Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio plus LPCM e Supports CEC bypass e Supports xvYCC e Equalises and recovers incoming TMDS data before re transmitting to ensure optimum signal quality e Supports Deep Colour up to 12 bit Code PU107 e1 65 58 HDBaseT HDMI Distribution Systems CHDBT gt New from CYP a range of HDMI HDBaseT distribution amplifiers Each model will take one HDMI input and send it uncompressed to two three or even seven outputs If you don t need the flexibility and cost of a full matrix system but want all the advantages that HDBaseT has to offer then these are perfect for both residential and commercial AV installations PU1H2HBTE PU1H3HBTL PU1H3HBTE PUTHTHBTE ae PU1H7HBTE Code PU1H2HBTE Two Way 454 89 Code PU1H3HBTL Three Way Lite 526 71 Code PUIH3HBTE Three Way 790 06 Code PU1H7HBTL Seven Way Lite 1053 42 Code PU1H7HBTE Seven Way 1699 84 Please note PU514LRX receiver is supplied separately p
51. and play for LAN Code KIRAM single module 59 99 Code KIRA pair of modules 108 00 KIRA128 The KIRA128 is capable of storing up to 128 IR codes in local memory These codes can then be accessed and triggered by any device with web browser capability from local network or internet For example the image opposite shows an iPhone browsing one the IRCM s internal web pages of stored IR commands Note this is a web page and not an app and so can be accessed by any smart phone PDA or other device with web browser capability The KIRA128 can be software configured as either a receiver a target or stand alone Once correctly configured one target can be used as a local IR emitter for multiple remote receivers The target can be another IR Anywhere KIRA or KIRA128 or the IR Commander Matrix IRCM DemoControl This free app gives you a graphical front end with which to access the 128 stored IR codes within the memory locations of a KIRA128 IRCM or KIRARS232 The app Is available on iTunes for free search DemoControl Email your order to us at sales keene co uk KIRA RS232 For extended integration options the KIRA RS232 provides IP control for both Infra Red and RS232 signals This model has no option for an external IR receiver although its still has an on board IR receiver should you need it In addition to the ability to send stored IR codes when triggered by IP commands it will also send stored IR cod
52. ansmitter unit to allow control from an extra room and a Powermid Eye twin IR emitter wand to control two extra devices Code PMIDKIT3 48 99 Other sources of infrared include sunlight fluorescent lights and LCD and plasma displays Keene IR receivers are carefully filtered to minimise any interference that might be caused by these sources but it always makes sense to try and position your IR receivers carefully Ideally try to position the receiver directly beneath or to one side of the screen and slightly behind the face of the screen do not have something reflective directly opposite and try to find a spot that will not be in direct sunlight SKY Plus SKY HD Remote Remote F kin Code SKYPREM 21 99 i Code s2 DAL 99 LETA F 0 IR Link Cables For direct connection of the IR Wand output to the IR receiver input on a Keene IR Distribution Amplifier Code KLDE10M 2 5mm to 3 5mm tip amp ring connected only 5 99 Code KLDE6M 3 5mm to 3 5mm tip and ring connected only 5 99 Jack Extension Cables Extension leads 3 5mm stereo jack plug to 3 5mm stereo socket to be used on Input or output as required We ve tested the input up to 10m and the output to 20m e m ae Code KLD40 3M 4 49 Code KLD405 5M 4 99 10M 8 99 Code KLD4010 CAT5 Cable Receiver Extenders If the Jack cable extenders aren t long enough or you already have some installed CAT5 cable you d lik
53. ation and to hear audio samples visit Wwww Ixymic com The IXY is compatible with iPhone 4S iPhone 4 iPad 3rd generation iPad 2 iPad amp iPod touch 4th generation NOT lightning connector 99 99 Code IXY Rode VideoMic Go Clear directional audio on the GO Compact and light weight by design the VideoMic GO delivers clear crisp directional audio with incredible ease of use Its tight pickup area focuses directly in front of the microphone and reduces other surrounding sounds ensuring that your subject is isolated from distracting background noise The integrated Rycote Lyre shock mount Isolates your microphone from bumps and vibrations that could otherwise interfere with your sound The VideoMic GO has no complicated switches or settings and is powered by your camera s external microphone input requiring no batteries to operate ensuring you never miss a great shot Specifications Line Gradient 0 50 Supercardioid 100Hz 16kHz 120dB SPL Minijack Output Acoustic Principle Capsule Polar Pattern Frequency Range Maximum SPL Output 59 99 Code RVMGO Audio Microphones Rode VideoMic Microphone The RODE VideoMic exhibits low noise and an unusually wide bandwidth for its size It is ultra lightweight and incorporates a shock mount to isolate camera body noise Its powered by a standard 9V PP3 type battery and complete with a low battery LED indicato
54. ations sent from the transmitter unit e HDMI version High speed with 3D support Can I send 3D HDMI to other rooms in the house This unit is the wall plate version e HDCP version 1 2 3D from a Blu ray player will only work via a correctly specified which receives HDMI signals sent _ Te Resolution 1080P 1080i 720P 576P 576i 480P 480i HDMI cable or an HDBaseT extender Lower resolution from the transmitter unit Lad interlaced 3D from sources such as Sky will work with almost e Data transfer rate Max 6 75Gbps all of the other extender systems e Dimensions of transmitter 111 x 75 x 23 5mm I haven t got enough HDMI sockets on my TV e Weight of transmitter 1190g In this instance you need a switchbox something that You can buy them as individual components e Weight of power supply 165g will take a number of HDMI devices in and let you choose Code H4T A output transmitter 229 00 which one is routed to the output Switchboxes can be DU O O Power supply SVC 4A ah tolastde ached I f Code H4SR Stand alone receiver 46 00 a gt ie ates automatic switch to last device switched on or manual front Gade Hue Wal plote recever 46 00 munaan O ota alone receiver 82 4 x 69 5 x 22mm pushbutton and or IR control Code H4IiRR R receiver unit 8 99 IR emitter and receiver lead length 1 5m I want to send an HDMI signal to another room Code H4IRE IR emitter 8 99 Dimensions 33 x 14 x 19mm UIOS ROUSE T There are several ways to accomp
55. automatically switch to whichever input device was switched on last with a manual override should you wish Brilliant neat tidy and very affordable just fit it and forget it Features e No need to make space for another piece of hardware e Integrated high quality 0 5m HDMI Cable removes need to purchase additional cable e Fully HDCP Compliant e Automatically switches to equipment source when switched on e Manual override switch e Self powered No additional PSU required e With plastic end connectors and regular shielded cable Code 28577H 2 9 a 9 9 HDMI 3 1 3 in 1 Out Micro Switchbox This Is a really tiny yet fully functional 3 to 1 HDMI Switchbox It will switch between 3 HDMI sources in multiple resolutions up to 1080p and route the signal to an HDMI output The unit will switch automatically to the device turned on and can also be manually switched via the push button An LED indicates which input is selected The case dimensions are just 52 x 52 x 18mm Features e Supports 12 bit deep colour full 1080p e Intelligent or manual switching e Supports HDMI v1 3b e High performance up to 2 5Gbps e Maintains high resolution video HDTV up to 1080p 2k 1440p graphics and computer resolutions up to 1920 x 1200 e No power needed Code HDMIM3 1 8 5 99 Specifications e 4 Port HDMI Switch e HDMI v1 3b e Supports up to 1080p e Supports 250Mhz 2 5Gbps per channel bandwidth e Supports 12 bit pe
56. ble for easy carrying and locks into the open position by a quick release latch It also has a braking device on each wheel to avoid accidental movement when filming Sliding screws lock the tripod feet into position to avoid unwanted movement between the tripod and dolly 95 00 Code TL2 Tracking Dolly with Track Enables you to create super smooth tracking shots with your own tripod The dolly has two sets of locating holes for the tripod legs which means the tripod can be used in both high and low positions It has eight radial ball bearing wheels which set the track width to the correct positions as the dolly moves down the track The Tracking Dolly is ideal for use on location or in the studio all you need is a reasonably flat surface The dollies width has been set to allow it to go through doorways it has its own levelling system which prevents any rocking should the track be on uneven ground It runs on inexpensive 40mm dia PVC pipe which can be supplied or is available from DIY stores The dolly will accept all tripods that have feet smaller than 45mm in diameter or with a base spreader 3 straps are supplied for securing your tripod to the dolly and also supplied are 2 track connectors for joining your track e Size L770mm xW620mm xH7Omm Weight 3kg e Transit size 770mm x180mm x180mm Kit price includes Tracking Dolly 3 straps 6 Track Connectors amp 12 metres of Track 8 x1 5m 6 me
57. bles At last an HDMI cable that doesn t feel like it s trying to escape from the socket you ve just plugged it into These Ultra Slim cables cram everything you need for the full HD experience into a very slim flexible cable Features e HDMI V1 4 compliant e Audio return Channel a e 3D support e AK x 2K resolution e Deep colour support e Ethernet up to 100Mbps e 36AWG ultra thin flex cable with gold plated connectors Code HDUSO5 length 0 5m 9 99 Code HDUS1 length 1 0m 11 99 Code HDUS3 length 3 0m 16 99 MINI HDMI range Cables with a standard type A HDMI plug at one end to the mini C type connector 10 42mm x 2 42mm at the other commonly used on camcorders and other portable AV devices Specifications e Fully wired 19pin connectors e HDCP compliant e High Speed rated e Up to 1080p resolutions HDMI plug to HDMI mini plug Code HDHDM2 length 2 0m 9 99 Code HDHDM3 length 3 0m 12 99 HDMI mini plug to HDMI mini plug Code HDMHDM2_ length 2 0m 9 99 Code HOMHDM3 length 3 0m 12 99 MICRO HDMI range Cables with a standard type A HDMI plug at one end to the micro type D connector 6 4mm x 2 8mm at the other commonly used on mobile phones Code HDHDMIC1 length 1 0m 9 99 Code HDHDMIC15 length 1 5m 11 99 Code HDHDMIC2 length 2 0m 13 99 HDMI CABLES High Speed with Ethernet Cables with High Speed 1080p support plus ethernet capability Code HDHD1405 lengt
58. box from your second TV by adding a magic Anywhere module directly to this Wired Eye which in If you want to use this for remote viewing via coax please eye simply connect it in line with the aerial by the turn sends the correct signal to the receiver via the coax be aware that the RF output is an analogue signal not a remote TV place the remote eye on top of the TV and connection Gives 100 reliable results and is invaluable in digital Freeview type you now have Infra red control of your preventing cross talk in multi receiver installations digibox from the remote TV Code IOLINK 23 99 Also available bundled with a SKLYLINK Sky Eye Code SKYLINK 6 99 Code KWE 1 9 s 99 Code IOLINKDEAL 31 99 IR Over RF Aerial Cable Aerial Splitter with DC Pass If you ve used RF aerial cable to run signals to another Very effective where wireless RF type solutions don t Through TV in the house you can use the same cable for IR have enough range or in cases where you want to keep Aerial splitter combiner with DC pass through suitable for control The Keene RF2IR product allows IR control any extra black boxes to a minimum use with Skylink and Triax IR control systems signals to be distributed via conventional aerial coax cable The IR receiver is the same as that used by the common sky eye type systems although it is not limited to satellite receivers and may be used with almost all IR controllable AV equipment It allows easy I
59. candescent lamps only Soft start and smooth dimming features Can be regulated from 0 lighting to the desired dim setting 22 30 Code LM12U X10 is a communication protocol for remote control of mains electrical devices It works by passing control signals through your existing mains wiring There are two essential parts to an X10 installation a transmitter and a receiver The transmitter generates the control signal switch on switch off brighten or dim and these signals are acted upon by receiver modules connected to the mains within the house In essence X10 allows you to assign a unique address to every electrical item you want controlled Commands can then be sent to each particular address allowing items to be turned on and off or dimmed as required There are a number of different ways to send a command to an address either by a timer remote control computer control wall switch or even by telephone You can have up to 256 unique addresses per house and of course some devices can be set to the same address so that one command can switch them all on or all off at the same time You can buy individual modules to build a system or buy a starter kit to get you going Because X10 uses your existing house wiring there are no extra cables to run and the beauty of the system is that you can expand it almost endlessly Most of the X10 products require no DIY skills at all you
60. ce of AA or AAA batteries the LED126T uses a Sony type lithium ion camcorder battery with a hefty 4600mAh capacity included to give plenty of shooting time Included in the package is a mains charger for the battery pack with a choice of three plug adaptors UK Euro US so that it can be used in many countries throughout the world Two filters are also included with the light a frossed diffusser and a yellow warm filter These simply slot into place on the front The LED126T can be either stand or camera mounted and comes complete with a standard sized cold shoe adaptor with locking thumb wheel this also has a 1 4 tripod thread in it s base and a mini shoe adaptor to enable the light to be used on the Sony Canon cameras with the smaller sized shoe fitting Code ore 99 99 LED256T Also available a 256 LED version Light including battery Weight 486gms Dimensions 29 x 9 x Depth 3 ins Code LED256T 1 2 9 99 Black Magic Intensity Pro Working in HDTV is exciting however HDV s heavy compression and limited 1440 x 1080 resolution can cause problems with video quality and editing Intensity Pro eliminates these problems by using direct capture from the camera image sensor at full 1920 x 1080 HDTV resolution and uncompressed video quality Both HDMI and Analogue Connections Intensity Pro enables you to capture directly from the HD cameras CCD bypassing the video compression chip for true uncompress
61. choice for film video engineering and voice over work Its light weight making it ideal for mounting directly to video cameras or on boom poles They have std 3 8 threads for attaching the mic or shockmount Three models are available The NTG1 amp 2 come complete with mount and windshield The windscreen effectively suppresses wind noise when recording outdoors in moderate conditions GREAT VALUE Standard Boom Pole length retracted 0 84m extended 3 0m Code RBP 79 00 Mini Boom Pole length retracted 0 82m extended 2 0m Code RMBP 69 00 Padded Case will fit all models complete with mic attached Code RBPBAG 24 99 Micro Boom Pole lightweight 2 0m extended Code MICROBP 29 99 Specifications e Output impedance 2500hm phantom NTG1 3500hm battery NTG2 e SN ratio 76 dB 1kHz e Maximum SPL 131dB 1 THD in 1KOhm e Dynamic range 113 dB e Power Supply voltage 1 5 V AA NTG2 or Phantom NTG1 2 e Current consumption 2 0 mA Boundary microphone ATR97 This is a low profile compact omni directional boundary microphone from Audio Technica designed for tabletop use Ideal for conferences meetings and placing on the head table at weddings Specifications e Size 58mm Diameter x 15mm high e Frequency response 50 15000Hz Impedance 1000 ohms e Cable length 1 5m e 3 5mm mono jack plus 6 25mm adaptor e Power 1 x LR44 battery included Rode NTG1 phantom power only
62. connection eeneg IE A small selection from the 5000 AV products HDMI 1 2 Distribution The Coosis 2 way HDMI Distribution amplifier is a compact device that gives two simultaneous HDMI outputs from one HDMI input ideal for viewing on multiple displays The Coosis units can also be cascaded together in a pyramid network to provide a one to many solution Please note If the max resolutions of your displays are different the EDID functionality will detect all the connected displays EDID nformation and auto match the output resolution to the lower one For example if one display supports 720P resolution and the rests support 1080P the signal will be lowered to 720p for all displays The quality of an HDMI cable has a great impact on signal transmission For best image quality we suggest you use a copper based HDMI cable Max recommended cable length after amplifier 10 metres Package contents 1 X Coosis 2 way HDMI Distribution amplifier 1 X Power Supply 5V DC 1A 1 X User Manual Code AV Switching amp Distribution Conversion amp Distribution CAT5 amp Networking Cabling a 2 Order Now Monday to Friday 9 00am and 5 00pm TA 2 7 8 9 10 11 12 13 on www keene co uk eigavidee 821 Wireless HDMI Sender e Replace your HDMI cable wirelessly and locate your HDTV or projector wherever you want e Mount the receiver out of sight behind your HDTV or on the ceiling n
63. cted to receive the Basic Kit surfaces IR signal and then send it out or emit it again in another asic Nl It is worth noting that IR emitter LEDs the sort of thing that location Over the years they have evolved and improved This kit comprising the Keene IR Distribution Amplifier is used in remote controls etc are like a torch and they have and now the IR receiver the distribution amplifier and 240V UK mains power adaptor 2 x universal emitter a narrow beam and will only shine onto a narrow area A the emitter are usually separate components The receiver wands IRUW and instruction leaflet Requires input device 10 or 15 degree beam width is not unusual can be positioned where you find convenient usually or IR receiver not included When you press a button on your remote control a somewhere near to the display The receiver picks up the microcontroller switches the IR emitter on and off very signal from your remote and sends this to the distribution quickly in a predetermined sequence This stream or amplifier which in turn sends it back out as IR to one or sequence of IR data can contain up to as many as 50 more emitters to control the equipment The net effect is digits The IR receiver on the equipment you are controlling that you can control your hidden equipment as easily as if picks up this IR data sends it to its microcontroller to be you were pointing the remote directly at it decoded and responds accordingly or
64. ctor Audio Inputs Digital S PDIF 1x via RCA Connector Analog Stereo 3x via RCA R L 2x via 3 5mm Mini Stereo Video Output HDMI v1 2 RGBHV 1x via HDMI Connector Audio Outputs Embedded into HDMI Digital per HDMI Spec Digital S PDIF 1x via RCA Coax Connector Audio Delay Adjustment Off 40ms 110ms 150ms Input Video Formats Supported HDMI v1 2 RGBHV YPbPr Up to WUXGA 1080p Analog RGBHV Up to WUXGA 60Hz Analog YPbPr Up to 1080p Analog Interlace Component 480i 5761 YUV DVI via HDMI Connector Up to WUXGA 1080p Composite and YC S Video NTSC or PAL Code 1TVS658 3 59 33 Find product information and data sheets on www keene co uk AV Switching amp Distribution Keene KPDA 1 5 Component Video amp Audio Distribution Amplifier e One input five fully buffered outputs Specifications e Unity gain e Wide bandwidth HDTV capable e Power requirements by external supply to DC input e Dimensions 220mm x 104mm x 43mm socket 2 1mm centre positive 12 18v DC Broadcast quality high speed video buffers 300mA or greater e Use for component video RGBs video RGsB video Video 5 buffered video outputs bandwidth 75MHz or four x composite video plus stereo audio up to 1080p e One video channel may be used for digital audio e Weight 780g excluding power supply e Level composite luminance 1v pp chrominance The KPDA is a high quality audio video distribution 0 3v peak to peak amplifier allowin
65. d for 4 16 ohm speakers e Black aluminium housing e individual volume controls with black aluminium finish e Accepts up to 14 gauge speaker cable e Individual A B switch per zone e Wiring Gauge14 to 22 gauge Specifications e Inputs 2 x stereo e Outputs 4 x stereo 4 to 16 ohms e Power per channel 100W max e Dimensions 432 x 133 x 64mm e Weight 3 67kg Code 24LMS 9 9 9 9 Wireless Surround Speaker Connection Kit Connect your present home cinema rear speakers wirelessly no more loose cables in your living room Uncompressed digital transfer ensures sound that goes beyond CD quality without interference or delay The built in amplifier in the receiver provides more than enough power for your rear surround speakers Automatic ON OFF function of both transmitter and receiver for trouble free use The volume is adjusted with your own remote because the transmitter is directly connected to the speaker output Local volume on transmitter and receiver for the correct balance between front and rear speakers Code SA220 9 8 a 9 6 Code HCP18 Wireless Speakers Enjoy your complete music collection anywhere in and around your home bath room kitchen shed etc wirelessly Garden party BBQ or a romantic evening with just the two of you on the balcony Create the perfect atmosphere with matching music Optimal music perception through high quality omni directional two way audio technology The sound is s
66. distinguish between these different types and route the IR signal accordingly 99 00 p Code KRFTW 29 99 Find product information and data sheets on www keene co uk IR Anywhere Powermind Infra Red over an IP Network What Why Keene have designed a range of products that are capable of sending and receiving IR signals across an IP network This can be across a LAN say from one room or office to another or even one from one side of the world to the other via the internet There are several ways to make use of this technology In its simplest form you can use one module as a real time IR to IP encoder and another module or group of modules as real time decoders to receive the IP signal and transmit as IR wherever the control is required Some of the modules also have on board memory that alows them to learn and store a number of IR codes Once the codes have been stored you can access the modules built in web page via any internet browser and tell it to emit the desired code s as required There are also a number of PC programs and apps specifically designed to send control signals via IP connected devices The Keene modules are compatible with an ever growing number of these and a list is maintained at www keene co uk iranywhere The modules all feature a built in standard 36 40 Khz IR receiver and the IR inputs and outputs are fully compatible with all of the existing Keene IR Distribution range so many other
67. e Camera shoe mount with 3 8 thread for easy boompole mounting 139 00 149 99 Code RVMPRO Code RVMPROKIT mic plus furry windshield Tie clip windgag A furry windjammer designed for lavalier tie clip mics to be worn on the outside of the body Supplied with removable foam inserts that can be combined with the supplied foam windgag to ensure a good fit Code WGTC e1 5 73 Rode Boom Poles Designed to be used with directional microphones held just out of shot a boom pole allows a subject freedom of movement and means you don t need to worry about visible cables or microphones as long as you have a good boom operator that is These boom poles from Rode are precision machined from high grade aluminium and are lightweight yet easy to adjust to the desired length with a secure twist locking action The poles have Velcro straps to externally secure a mic cable or the end caps can be removed and an XLR cable threaded internally through the tube Rode NGT1 amp NTG2 Shotgun The RODE NTG1 and NGT2 are lightweight condenser shotgun microphones designed for professional applications within the film video television and production industries The 48V phantom powered NTG1 phantom operating power only NTG2 has additional battery power option and NTG2 provides a balanced low impedance output stage Wide bandwidth and controlled polar response coupled with low noise SMT electronics make the NTG1 the perfect
68. e to use then these will solve the problem This kit consists of a pair of short 25cm line adaptors one with an RJ45 line socket to a 3 5mm stereo jack plug and the other with an RJ45 line socket to a 3 5mm stereo jack socket To use simply plug the IR receiver in to the 3 5mm jack socket of one adaptor and the 3 5mm plug of the other adaptor goes into the IR receiver input of your IRBKIT or IR Commander Connect your Cat5 6 standard wired network cable in between the adaptors and that Is it Using this method it is possible to remote mount IR receivers at distances of up to 100m 9 99 Extra Long CAT5 Cable Receiver Extenders If you need to extend even further then the new KA175XLE uses a line driver meaning you can extend by up to a full 305m reel of CAT5 cable Code KA175 Code KA175XLE 1 9 a 99 CAT5 Cable Economisers Although CAT5 cables have four pairs of conductors 10base and 100base systems only use two of these pairs so half of the cable is redundant These cable economisers allow you to route two IP signals down a single Cat5 cable Ideal for use with the IR Anywhere modules as it allows you to add remote control without having to utilise an extra remote network hub or switch Supplied in pairs Note CANNOT be used with Gigabit networks or anything using POE Code KA201 19 99 Kramer BNC Cables HD SDI These cables are constructed of high performance RG 6 cable with 75 ohm BNC connectors at
69. eater The AU 11SA is an advanced solution for HDMI to HDMI repeating with Audio de embedding It is compatible with v1 3 HDMI specifications a cutting edge technology which defines the transfer of deep colour 12 bit video with a high bandwidth of up to 225Mhz Connect to source and display HDMI select the required audio format amp output your audio format to your amplifier Features e Compliant with V1 3 HDMI HDCP 1 1 and DVI1 1 e Decodes HDMI audio to analogue and digital e Corrects digital error and automatically provides equalisation up to 40dB e Supports high definition input up to 1080p output resolution follows input e Supports HDMI signal amplification and equalisation output for repeater function can be used to extend up to 35m Digital Audio over CAT6 The PU 304 KIT is designed to send digital audio signals over 150m This device supports both Coaxial and Optical signals and can transmit these signals up to 150m The PU 304 KIT can be powered using a USB cable or the supplied PSU adaptor for added flexibility in a compact design Digital SPDIF signals are supported up to a sample rate of 96Khz and support for Stereo and Multichannel digital audio LPCM DTS Dolby Digital Dolby Digital Plus also provided Digital audio convertors Convert digital optical audio signals TOSlink into RCA coaxial S PDIF and vice versa Dimensions 20mm x 71mm x 46mm Power supply 6vDC 250mA i
70. ect attachment to the equipment fascia Low profile design ideal for use in tight spaces Dimensions of emitter L x 25mm x W 9mm x D 6mm Fitted with a 1 2 metre cable Code IRSFW a 99 Email your order to us at sales keene co uk Keene IR Receiver Adaptor KRECA This device allows Keene IR receivers to be used with other manufacturers IR distribution systems for example Xantech Onkyo Harmon Kardon etc The design allows a number of parameters to be changed including Data 5v or 12v and Carrier signal exclude include Supplied complete with a 3 5mm jack to jack 1 2m link cable Sm fa a E et i s i Pa d iy t A T Fi y A La a a Code KRECA 3 9 9 9 Anything To Keene IR Translator KIRT The Keene IR Translator is designed to allow you to connect the IR wand output from any device directly into the IR _ receiver input of any Keene IR equipment such as an IRBKIT IRCM IR Anywhere module etc This is particularly useful with HDMI video over distance systems as the single IR wand output is usually insufficient for effective control of multiple sources The 3 pole input connector is optically coupled and will work with any connection as positive or negative Compatible with IR frequencies between 10Khz 200KHz 19 99 Code KIRT Also available KIRT12 for non keene 12v based IR systems 19 99 IR Emitter Shield Keene IR Emitter Shield A soft flexible rubber cover that will
71. ed video quality Featuring both HDMI and analogue video connections means Intensity Pro works with a massive range of cameras televisions and video projectors Code BINTSPRO 1 48 1 5 Email your order to us at sales keene co uk D SLR Shoulder Rig This is a lightweight compact rig ideal for DSLR s and camcorders It has a gadget bag friendly size when folded and extends out to provide a variety of different support options Features e Small folded design for easy gadget bag carrying e Versatile design for many different shooting styles e Extendable rear arm e several threaded holes for mounting monitors lights amp microphones All hand grips and joint are rotatable and adjustable e Non slip foam hand grips Specifications e Weight 1 1Kg e Dimensions 30 x 17 x 8 5cm folded Black Widow Spider Spider Holster for lightweight DSLRs and point and shoot cameras e No more dangling cameras from your neck and shoulders e Both hands and upper body free e Securely locks your camera in each time it s placed into the holster Works with your tripod quick release plate e Use with your belt or the special Black Widow Belt optional 639 99 Code BWS Spider Pro Single Camera System Shoot from the hip The SpiderPro single camera system contains everything that you need to carry one camera including SpiderPro Belt SpiderPro Holster which securely attaches to the Belt SpiderPro Plate which
72. ensions per plug in module 46 Digital TV Anywhere Digital wireless sender for all your Digital TV Channels Features e Watch digital TV far away from the decoder e Watch and operate the digital TV channels from your decoder anywhere e Extra functionality such as Video on Demand Pay TV Electronic Programme Guide Time Shift and Digital Video Recorder DVR also remain available and usable e Place your TV wherever you want without having to consider the location of the aerial or satellite connection and without laying cables or drilling holes e Retain original sound and picture quality as a result of digital transmission Set Contents e 1 AV Transmitter e 1 A V Receiver e 2 Power adapters e 1 IR Extender cable e 2 SCART cables e 2 Stands e 1 User manual Code DIVA 1 1 9 70 The set comprises a transmitter and a receiver Connect the transmitter to the SCART output on your decoder that is connected to the aerial or satellite connection Then connect the receiver to the TV The set sends on the picture sound and commands from your remote control wirelessly CELESTRON DIGITAL MICROSCOPE A great product for education discovery work and fun This innovative microscope design allows you to view specimens or objects on a computer screen and allows you to take snapshot images or short videos A rugged metal stand is included for holding the microscope steady at various positions for viewing and or imagi
73. er needs to be compatible with multicast The HDMI signal is dynamically compressed e Simultaneous HDMI outputs l i although in practical terms it s extremely hard to notice Specifications e Inputs 1x HDMI 1x HDMI Uncompressed AV and Data e Wireless HDMI video sender advantages neat and tidy no cables to worry about IR e 1x USB Mini B 1x Service Port Propriety Data feedback built in Easy to move from room to room The e Outputs 2x HDMI 2x HDMI Uncompressed AV and Data HDMI signal is uncompressed PSU 5V 2 6A 6 5 disadvantages relatively short range most suited to Code SY4KS 1 7 5 within room or adjacent room use Find product information and data sheets on www keene co uk Power Solutions Internet Controllable Mains Switch New from Keene the IPMSW1 is an IP controllable mains power switch It has two independent mains outlets that can be controlled in a number of ways Features e Simple browser button based on off control e Full browser based set up and timer configuration e Adjustable power fail re start options allow each switch to delay up to 255 seconds before switching on Ideal for remote re start of systems that require 2 stage start ups e 3 timer events per switch with daily weekly or monthly repeats e During each timer event the switch can be set to either on or off e Own IP address so can be controlled via internet using port forwarding e Support for DDNS e
74. es amp Panels Scart outlet plates Scart outlet plate which fits a standard UK single pattress and provides a scart socket The rear of the sockets have solder type connections Code HCP11 white Code HCP11S steel finish Scart outlet plate QC We ve enhanced the HCP11 scart wall outlet plate to a quick connect solderless version This QC series plate has handy screw terminals making Installation much easier than with conventional solder type connections The terminal blocks are rising clamp style 6A rated and can accept cable up to 1mm sq Code HCP11QC 13 99 Scart outlet plate QC Steel The Quick Connect Scart plate is also available in a brushed stainless steel finish Code HCP11QCS 22 99 HDMI outlet plates From Keene a wall plate with an HDMI socket at the front and a PCB mounted rear socket The rear socket is aligned such that a side entry HDMI cable should pass through one of the side knock outs in a std metal rear pattresses Depending on the size of plug used some modification to the pattress may be necessary We can supply this item as follows Code HCP26 single white 19 99 Code HCP26D double white 29 99 Code HCP26S single steel 39 99 Code HCP26SD double steel 54 99 Code HCP26FC single white with flexible rear connector 29 99 Code HCP26FS single flat brushed steel finish 39 99 24 x CAT5E 1U Code PP11 29 99 24 x CAT6 1U Code PP12 34 99 14 x HDMI C
75. es when triggered by Keene defined ASCII commands via RS232 The KIRARS232 can function as e IR to TCP IP bridge e RS232 to TCP IP bridge e TCP IP to RS232 for the CTX35 X10 bridge e RS232 to IR stored codes e RS232 disabled function as KIRA128 e Supports baud 2400 9600 19200 57600 115200 Code KIRARS232 84 99 Browser Control The image above shows an iPhone browsing one of the KIRA128 s internal web pages of stored IR commands Note this is a web page and not an app and so can be accessed by any smart phone PDA or other device with web browser capability KIRACC Contact Closure The new Keene KIRACC Contact Closure module provides a number of ways to control devices via local network and the internet Commands can be issued simply by accessing the built in web pages via any device with a browser and the open API structure means it can integrate seamlessly with a number of other IP control systems and apps for tables and smart phones Infra Red e Infra Red over IP use either as a real time IR transmitter in conjunction with another KIRA module or use IP control to blast any of the 150 codes stored within the on board memory e Two IR Emitter outputs individually routable e 20 macro commands each up to 30 steps e Built in dedicated high accuracy IR learning receiver e IR codes stored within the on board memory Contact Closure e Two Isolated relay contacts each rated at 48v
76. evel hold Easy to read 21 bar graphical display Size approx 159 x 64 x 48mm e Power PP3 type 9v battery not supplied Code Audio Ground Loop Isolator A low level filter designed to isolate the ground between source and amplification to prevent noise or hum Can be used for in car applications to eliminate alternator and engine noise or any audio installation that suffers from ground loop mains hum Simple in line connections phono plugs to phono sockets make for easy installation and no external power Is required Gold plated connections Code Digital Audio Lip Sync Corrector The definitive answer to lip sync error for up to four sources Do you sometimes get frustrated by the lip synch errors when viewing It occurs because of a delay introduced by the processing of the picture The audio doesnt go through the same processing hence the audio appears ahead of the image If you use an AV amplifier for your sound then we have a solution the Felston DD740 digital audio delay module It allows easy adjustable audio delay allowing you to get everything back in perfect sync There are four inputs and you can switch and adjust from your armchair with the supplied remote 680ms delay 340ms for 96kHz signals On the fly adjustment with no image overlay Tweaking in 1ms and 1 3ms steps 36 preset delays for instant recall Fully featured remote control with numeric keypad for discrete delay entry Discrete inp
77. ext to your projector No more visible cables e Watch up to 2 HD devices such as Blu ray players DVRs HD set top boxes game consoles etc and easily switch between the sources connected without changing plugs e The built in HDMI splitter means that you can continue to watch the connected devices locally Operate your A V sources from anywhere even through a wall or cupboard door using the IR receiver e The HD signal does not experience any delays and is therefore perfect for game consoles Digitally supports all 480p 720p 10801 and 1080p Full HD resolutions from up to 30 metres Code Digital Audio Lip Sync Corrector e Absolutley the best most definitive answer to lip sync problems on the market today 680ms delay 340ms for 96kHz signals On the fly adjustment with no image overlay e Tweaking in 1ms and 1 3ms steps 36 preset delays for instant recall Discrete input switching with input s last delay restored e Automatic optical to coax coax to optical conversion 4 digital audio inputs 2 digital audio outputs optical and coax Bluetooth In Wall Stereo Amplifier e Add music to you kitchen bedroom bathroom study e Powerful true 20W RMS per channel output e Fits into a standard UK two gang pattress e Built In FM Radio with ten station memory eo Front Jack input Rear line level input Bluetooth for easy music streaming from phone or tablet e Front panel control plus Infra Red remote control e Smooth
78. fail re start options allow each switch to delay up to 255 seconds before switching on Ideal for remote re start of systems that require 2 stage start ups e 3 timer events per switch with daily weekly or monthly repeats e During each timer event the switch can be set to either on or off e Own IP address so can be controlled via internet using port forwarding e Support for DDNS e Manual override button for each switch e Optionally use internet time servers to set internal clock Internal Real Time Clock IC with 5 year battery backup Code IRCM e1 69 99 Find product information and data sheets on www keene co uk IR Distribution Devices that give you wireless control of your AV devices from another room POWERMID The Powermid remote extender system allows remote control of IR operated equipment from anywhere in the house It comprises a pair of small pyramid shaped devices The transmitter picks up the IR from your remote converts it to a radio signal and beams it to the receiver The receiver then converts the radio signal back into IR to control your devices Quick and easy to install and ultra reliable Can be used in room or even through walls and floors It can also be used as a wireless room extension for any of the Keene IR Distribution amplifiers by simply cabling the IR wand output from the Powermid into the IR receiver input on the Keene unit using a KLDE6M cable Additional transmitters amp
79. from Seagull a compact and nicely made LED light ring with flash function The power pack and control unit fits onto the hot shoe on top of your DSLR whilst the LED light ring is mounted around the lens via an adaptor ring screwed direct into the camera s filter thread The control unit has a three position slider switch on the back for off light only on and light plus flash on The brightness is controllable via a rotating wheel and so you can tailor your light output to your situation The flash function is four times brighter than the output of the constant light to give you plenty of oomph for the shot There is also a test button so you can experiment before shooting begins It comes complete with six adaptor rings to fit it to 52 55 58 62 67 and 72mm camera threads and it can be adapted easily to other sizes by using additional stepping rings please just give us a call as we can supply most sizes from stock at reasonable prices PROFESSIONAL D SLR TWIN BATTERY CHARGER The Hanel ProCube is a high quality metal bodied charger for use with Canon E6 and Nikon EL14 EL15 batteries It will also charge 4 x AA batteries and provides a high current USB charge outlet making it the ideal one charger does all companion for pro photographers on the move Supplied with UK Euro US mains plugs and as well as a 12v car cigar lead Features Charges 1 or 2 DSLR batteries simultaneously Intelligent fast IC charge control with LC
80. g one video and audio source to Distortion components lt 50db up to 10MHz simultaneously supply up to five other devices It uses a ORCI A rele ao tan O very high quality high bandwidth ICs to ensure that Sach ene ii EUA each output is not discernible from the input making it ideally suited to driving multiple displays or making multiple copies from one source There are two stereo audio channels and four video channels making it e Back terminated series 75 Ohm outputs for reflection free performance e DC coupled on all outputs suitable for use with component video RGBs video e Slew rate up to 500v uS RGsB video or 4 x composite video plus audio Any of e Audio 5 buffered audio outputs the video channels can also be used for digital audio e Distortion lt 0 1 if desired Bandwidth 20Hz 30kHz e Output impedance lt 1k ohm each output Input impedance gt 10K ohm Code KPDA 59 99 Keene SDA 1 5 Scart Distribution Amplifier One input to five outputs fully buffered using Specifications broadcast grade video amplification ICs Pin 8 is routed e Power 12 18v DC 300mA through if the input goes high all the outputs go e Video 5 buffered video outputs high and every pin connection is carried through amp Video bandwidth SOM making it suitable for composite S video component or RGB Supplied in a robust metal case this is ideal for Chrominance 0 3v peak to peak displaying one signal on multiple TVs or for ma
81. grated PB5000P Features e 1080p Ultra High Quality Video transmission and up to 16 Groups Multi Casting e Flexible and scalable HDMI 1080p broadcasting with Gigabit Ethernet LAN e 1 to 1 1 to many amp multi casting broadcasting architecture adding more displays without adding LAN bandwidth loading e Multi Casting group with Gigabit Ethernet managed switch required 802 11Q VLAN amp IGMP function support up to 16 multi casting group support e 16 sets C class IP Dip switch configuration on both Sender amp Receiver for easy Multi Casting group matching Specifications e Video Resolution 4801 p 576i p 720p 1080i p e Sender Connector Power Adapter in RJ45 RS232 IR Emitter Connector HDMI e Receiver Connector Power Adapter in RJ45 RS232 IR Receiver Connector HDMI out e HDMI Spec 1 3 Compatible e DVI Spec 1 0 Compliant e HDCP Spec 1 2 Compliant e Link Connector RJ45 e Power Consumption 3 2W e Audio System Stereo L R e Audio Resolution 1 6bit 48Khz e max CAT5 Cable Length 100M e Power Adapter DC 5V 2A Code PB5000P Code PB5000PR e IR Pass Thru on 1 to 1 extender configuration e Up to 16 Groups Multi Casting e IR Control Pass Thru e Two Way RS 232 Command Unicast Broadcast for control from remote site e Easy Dip Switch Matching for Multi Casting Group configuration e New EDID Copy Video Mode Switching Button for Optimal Video Performance e Video Wall function support for up to 8x16 di
82. h 0 5m 3 99 Code HDHD141 length 1m 4 99 Code HDHD1418 length 1 8m 11 99 Code HDHD143 length 3 0m 14 99 Code HDHD145 length 5 0m 17 99 Code HDHD1410 length 10 0m 34 99 HDMI Adaptors Code KA191 270 degree rotation 7 99 Code KA191L 90 degree rotation 7 99 Code KA191F 90 degree flat 6 99 Code KA213 270 degree flat 6 99 Email your order to us at sales keene co uk Coosis Python HDMI Cables The Coosis Python series of HDMI cables are ultimate High Speed with Ethernet cables Cat 2 for HD signal transmission Upto 15 8G bandwidth permits a lossless transmision of uncompressed 4K x 2K high definition pictures with maximum 48bit px colour depth It also integrates an HDMI Ethernet Channel HEC which allows for a 100 Mbit s Ethernet connection between the two HDMI connected devices so they can share an Internet connection Additional Audio Return Channel enables a TV via a single HDMI cable to send audio data upstream to an A V receiver or surround sound system increasing user flexibility and eliminating the need for any separate S PDIF audio connection Each cable is also supplied complete with an HDMI plug to socket 180 degree swivel adaptor allowing it to be used even in very tight spaces PFG4 FLAT GOLD 1 22M 19 99 PFG8 FLAT GOLD 2 44M 23 99 PFG16 FLAT GOLD 4 88M 40 99 PFG25 FLAT GOLD 7 62M 51 99 PFG35 FLAT GOLD 10 67M 58 99 PFG40 FLAT GOLD 12 2M 70 99 PFG50 FLAT GOLD 15 2
83. his Is a really good choice You can easily add to it and expand the system later if needed 49 99 Code IRBKITPB Panel mount receiver in black 65 00 Code IRBKITF z naon oaa a EGE 0O Code IRBKITPW Panel mount receiver in white 65 00 Code IRBKITS 48 00 Email your order to us at sales keene co uk IR Distribution Systems IRBKIT MINI a IRPRO4 SYSTEM e eles vet a The IR Pro4 Distribution amplifier has some powerful The IR Pro4 is very flexible allowing for a number of mais Be features for demanding installations It has four IR configurations that will solve most IR control equipment located in positions where your remote Receiver inputs and uniquely all four receivers can be problems wouldn t normally work For example equipment placed inside cabinets with closing doors or located on shelves behind you or around a corner Because of the compact located in the same room if needed Normally multiple IR receivers will cause timing issues and poor performance but the Pro4 has BestSelect technology Direct cabled input that can be used with other e Four BestSelect IR Receiver inputs eee ee ee aan also T which automatically locks on to the strongest IR signal manufacturers IR Blaster outputs attached to the rear of a wall mounted display ideal for eee l l aie and shuts down the other inputs within a fraction of a e Four IR Emitter outputs for use with any Keene IR use with items such as Apple TV
84. ignal In addition either a bitstream derived HDMI audio signal or a coaxial input signal is processed and provided to an external audio amplifier via a coaxial S PDIF digital audio connector The VS 226 provides a convenient way for the user to watch a high definition television program while also recording it in standard resolution via a DVR or VCR Features and Specifications e Automatic Signal Conversion e HDMI 1 2 HDCP1 1 and DVI1 0 compliant e HDMI or DVI HDTV Signals from 480p to 1080p e Jitter corrected Re Clocked HDMI Bypass signal e HDMI or DVI HDTV to NTSC or PAL Conversion e Converts HDMI Bitstream audio to S PDIF Audio Provides analog L R Stereo Audio Output e Converts PC signals to UXGA 60Hz to NTSC PAL Important Please be aware that this unit will not output composite video s video or stereo audio from an HDCP protected source A source such as a Blu ray or SkyHD usually uses HDCP and so only the HDMI loop through and digital audio ouput will be active If you would like any guidance with this please don t hesitate to contact us Code VS226 6222 1 0 Email your order to us at sales keene co uk RGB Conversion amp Distribution RGB SCART amp S video to HDMI 1080p HD Convertor This device contains a high quality chipset to convert analogue Scart AV signals RGB or composite or s video and upscale them to a choice of HDMI resolutions 720p 1080p 1680x1050 1360x768 and a choice of screen mode
85. indicate which input is active When IR activity is detected on one input all other inputs are momentarily blanked to ensure the signal remains pure and is cleanly transmitted the LEDs may be disabled if required e Expansion module sockets for inputs and outputs Allows an additional 4 input or output module to be connected via CAT5 cable at a distance of up to 50m RS232 e Contains a TCP IP to RS232 sever that can be used as an RS232 TCP IP bridge e RS232 strings can be stored in on board memory and triggered by IP from an app or as part of a macro Power e Built in Power over Ethernet PoE capability TCP IP e Can act as a UDP target for IR Anywhere modules e Built in support for dynamic DNS client for non static IP addresses Code KIRACC p 29 99 CTX35 RS232 to X10 Bridge The Marmitek CTX35 communication transceiver can receive and transmit standard X10 control signals via the RS232 port Transmit commands and received data are in ASCII format and it is directly compatible with the KIRARS232 giving you the ability to TCP IP control your X10 products from anywhere in the world 199 99 IP Controllable Mains Switch The IPMSW1 is an IP controllable mains power switch It has two independent mains outlets that can be controlled in a number of ways Code CTX35 Features e Simple browser button based on off control e Full browser based set up and timer configuration e Adjustable power
86. ions or other HDMI over CATS extenders to give amazing results downscale a UHD 4K signal to 1080p 24 for integration into any AV system The ability to downscale 4K signals to advantages One single CAT5E cable send crystal clear 3D 1080p is a crucial function when working with 4K sources in a complex AV system and distributing the HDMI sources to HDMI at 1080P with 7 1channel audio and also provides IR multiple displays which have varying resolution support This device allows the user to select the highest commonly control RS232 and extend your 100Mbps LAN supported resolution between source and display ensuring maximum compatibility in any system The SY 4KS incorporates two HDMI outputs one of which is a bypass input follows output and the second is a scaled output The scaled output can be set to three modes upscale to 4K downscale from 4K or as a bypass output Both the bypass output and scaled d HDMI over IP network output operate simultaneously advantages If the IP network is already installed then no extra cabling is required Can also be used with homeplug ethernet over mains adaptors IR feedback is built into the unit Plug and play with no configuration Other network receivers can easily be added in different rooms disadvantages relatively expensive Features e Supports HDMI upscaling to 4K or downscale to 1080p 24 disadvantages The audio output is stereo not e Supports HDMI signal bypass multichannel The IP rout
87. is a clear white or light grey wall This kit is the MPW 20 Tailor made Screen amp Border Kit for 6 m 64 sq ft of projection screen The MPW 20 kit includes BaseCoat with ContrastBooster TopCoat with BrightnessBooster and MagneCoat with MagneBorder All the required tools are included as well Contains e 1 4 litre BaseCoat e 0 1 litre ContrastBooster for BaseCoat e 0 9 litre TopCoat e 0 1 litre BrightnessBooster for TopCoat e 0 4 litre MagneCoat e 10 metres 32 8 ft of MagneBorder width 5 5cm 2 2 includes all necessary tools other Mighty Brighty kits and accessories are available please see keene co uk for details Code MPW20 Paint amp Border Kit 169 00 Also available MPW10 Standard Kit contains Contains 1 BaseCoat Light Grey amp 1 TopCoat Brightness Gain 1 1 84 00 Remote Control Mains Socket Set A really easy way to automate your home use for table lamps fans heaters anything you like really The set contains one remote control and three plug in switches The plug in switches also have a manual on off button and LED status indication e Up to 30m range e Remote control push buttons and sockets are numbered eg Button 1 operates socket 1 only e Manual On Off switch with LED indicator e Remote battery A23A supplied e Mains power LED indicator x 72 x 140mm Code RCS3 3 way Code RCS5 5 way Specifications e Power supply 230Vac 50Hz e Power max 13A 2990W e Dim
88. k for MP3 players Rear line level audio input e Push button or IR remote control e Smooth tactile moisture resistant front panel e Flush mount or surface mount 25mm depth e Smooth tactile moisture resistant front panel KLAB Bluetooth Digital Models These models add Bluetooth capability to the KLAB Digital Amplifiers so you can stream audio wirelessly from your phone or tablet e Flush mount or surface mount 25mm depth Features e 20 RMS per channel output e Bluetooth connectivity Code KLAB20DB Bluetooth Amp amp Remote white 149 99 Class D digital circuitry Code KLABKITDB Bluetooth Amp PSU amp Remote white 179 99 e Built in FM Radio The Bluetooth KLAB20DB can be purchased with either a grey or white fascia surround e Front 3 5mm input jack for MP3 players 149 99 s Paap linedeval audis input Code KLAB20DBG Bluetooth Amp amp Remote grey Code KLABKITDBG Bluetooth Amp PSU amp Remote grey 179 99 e Push button or IR remote control KRC1 remote control Email your order to us at sales keene co uk a ail KLAB20 analogue The KLAB amp KLABF amplifiers can be configured via PCB links to operate in fixed gain mode for commercial and industrial applications This enables the amplifier to perform at a predetermined level usually 100 as soon as power is applied pe KLAB20F analogue KLAB20D digital KLAB20DB bluetooth white s 1 l ee KLAB20DBG
89. king up to five simultaneous copies from one source Mains e Video distortion lt 50db up to 10Mhz adaptor included e Back terminated series 75R outputs for reflection free performance e Video level Composite Luminance 1v pp e DC coupled on all outputs e Slew rate up to 500v uS e Audio 5 buffered audio outputs BULK PRICING 50 available for e Audio distortion lt 0 1 Bandwidth 20Hz 30KHz all products on this page e Audio output impedance lt 1K ohms each output e Audio input impedance gt 10K ohms Unity gain e Dimensions 219 x 115 x 37mm e Weight 725g exc supply amp cables Code SDA UK model with UK 3 pin mains plug order 99 99 Code SDAE Euro model with round 2 pin mains plug order 99 99 Keene KDA 1 4 AV Distribution Amplifier The Keene KDA distribution amplifier has one set of inputs for composite video s video and stereo audio and four identical sets of outputs each output being indistinguishable from the input Uniquely the Keene Distribution Amp also has a switchable line drive feature giving the ability to send audio and or video over much longer cable runs than normally possible up to 100m dependant on cable The KDA may be daisy chained that is to say the output of one KDA may be fed into the input of another Used in such a configuration five KDA s may be used to provide up to 16 AV outlets from one AV input This product is ideal for Sending an AV signal to multiple displays
90. l this revolutionary new device is compatible with Final Cut Pro 7 Adobe Premiere Pro Adobe After Effects Nuke DaVinci Resolve and more Machined from a solid piece of aluminum Intensity Extreme gives you Incredible quality HDMI component video s video and composite 10 bit capture and playback Better still this super sleek high speed data transfer system offers an incredible 10 Gb s connection that s up to 20 times faster than USB 2 0 and up to 11 5 times faster than FireWire 800 Incredible quality HDMI capture and playback Intensity lets you capture and playback in the most incredible quality of HDMI and component analogue video in both SD and HD Smash the quality barrier for your video work because Intensity is not only the highest quality but also affordable Code SPSCS 1 09 94 Professional Performance Code SPDCS 1 89 99 See www keene co uk for the full range of Spider Holsters amp accessories Go beyond the limits of your AVCHD or HDV camera Simply plug using HDMI or analogue and capture direct from your camera s CCD You get incredible quality that completely bypasses the camera s video compression Use Intensity for monitoring from your edit software for maximum real time effects Intensity connects direct to your editing software s real time effects processing Use Popular Video Software Intensity works with the software you love to use Use DirectShow and QuickTime software
91. lation level Factory set for 75 qevice Hesigned primari TOF USS with UK SKY Satelite I ang used to distribute signals to other TV s via the RF Composite video plus audio input ea ee ae ue aerial cable The AV signal can be positioned on any e Scart input can be used as buffered loop suited to installations of multiple SKY receivers as It is vacant RE channel between 21 and 69 This means for through output able to sree the problem of receivers of the uae example that the signal from a security camera could e RF Channel PLL channel 21 69 type all responding to the same IR code The KERC is be introduced into the aerial lead and viewed in the e Compact size 120mm x 85mm x 30mm e Weight 150g able to decode the different modes of SKY IR control signals and route them to specific receiver outputs as required same way and as easily as any normal broadcast signal There is a seven segment LED display for clear channel indication together with a last channel memory in the It achieves this by making use of a facility already built in event of a power failure BULK PRICING 50 and to the remote control The supplied remote control for T n each SKY receiver can be set to one of three different a a te WANE NEON AD ack OEM AVAILABLE on this product receiver types standard SKY amp SKYHD and also to one of four different modes 0 1 2 amp 3 giving a total of 12 possible types of IR code The KERC is able to
92. lease see website for details HDBaseT Lite HDMI Extender The PU 513 514 systems allow uncompressed HDMI IR and RS 232 signals to be transmitted over a Single CAT5e 6 cable to distances of up to 60m Features e HDMI 1 4 with 3D 4Kx2K support HDCP and DVI compliant e Supports HDMI 1 4 including HDCP over a single CAT5e 6 up to 60m e Complies with HDBaseT Lite specifications e Full HD resolution support 10800 60H2z 36 bit 3D over 60m 4Kx2K over 40m and PC resolution support VGA to WUXGA over CAT5e 6 cable e HDMI input up to 15m with 8 bit deep colour or 10m with 12 bit deep colour e Supports HDMI output up to 15m with 8 12 bit deep colour e Supports IR and RS 232 Control e Supports High Definition LPCM 7 1CH Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio transmission With one way IR receiver back to transmitter Code PU513L 2 53 78 With two way IR control Code PE514L 255 87 Email your order to us at sales keene co uk HDMI Over Long Distances Features HDMI over CATS E Extender v1 3 HDMI HDCP 1 1 and DVI 1 1 compliant HDMIFAQ The CYP PU1106 HDMI over CAT6 Extender Set with IR s Lipliner CATE EdieiderSer Pass through is the perfect solution to extend HDMI signals via CAT cabling up to 40m The PU 1106 also allows you to use your existing Remote Control to control your device e Resolutions supported PC VGA to WXGA HDTV 480i I want to split my HDMI signal to 1
93. lish this You can choose Or as complete kits including the IR receivers and emitters between Code H4KIT1 with 1 x transmitter F a A very long HDMI cable x stand alone receivers advantages Preservation of all content Some of the other methods will not send multichannel audio for example disadvantages long HDMI cables are usually thicker and so unwieldy and difficult to route through wall space and trunking Code H4KIT2 with 1 x transmitter x stand alone receivers 4 x IR receivers and 2 x IR receivers and 1 x IR emitter 315 00 H4KIT2 1 x IR emitter 399 00 i Ti Ei Li Li j Max length usually 20m Notoriously unpredictable results Code H4KIT3 an 1 i r depending upon equipment used IR feedback will require x wall plate receivers T i 2 x IR receivers and H4KIT4 a ee ae other equipment 1 x IR emitter 315 00 b HDMI over CAT5 6 baluns Code H4kIT4 a sae eas You can also use two wall plates as a single room to room advantages CATS cable is cheap by comparison and 4 x IR receivers and option flexible so easy to run through wall spaces and trunking 1 x IR emitter 399 00 code HwPK 4 output transmitter 79 99 Max length can be up to 60m disadvantages some models do not provide IR feedback some models require two separate runs of CAT5 HDMI 4K Scaler FON l c HDMI over HDBaseT Uses different technology to The SY 4KS HDMI Scaler is designed to upscale 1080p 24 signals to 4K Ultra High Definition UHD resolut
94. lored for voice frequency response an ON L E D a direct headphone amp and of course very low self noise The mic opens up possibilities for anyone who records audio from podcasters journalists and students to business people adding audio files to websites and multimedia presentations p e High quality broadcast Ko E sound a e Dynamic capsule neodymium 28 mm e 18 Bit Resolution 8KHz to 48KHz sampling e Windows and Mac compatible e Tight Cardioid pattern for superior off axis sound rejection e Powered from USB Bus e Includes Microphone Stand Mount and a 3m 40 USB cable e Internal capsule shock mounting e 3 5mm stereo headphone jack output with volume control Power Requirements Power supplied from USB port Weight mic only 610g 21 5 oz Dimensions Length 215mm 8 Height 56mm 2 Width 52mm 2 139 00 We also offer the Podcaster in money saving kits Code RPC1 Podcaster plus PSM1 shockmount Code rpcikitt 165 00 Podcaster plus PSA1 angle poise stand amp PSM1 shockmount Coderpcikit2 230 00 Keene are major RODE stockists and this is just a fraction of the range we can supply Please call or check www keene co uk for more details Email your order to us at sales keene co uk Rode Smart Lavalier Microphone The smartLav is a protessional grade wearable microphone designed for use in a wide range of film television and b
95. n Deep Color Mode at up to 36 bits 12bits color and new lossless compressed Dolby TrueHD Dolby Digital Plus and DTS HD master Audio digital audio e Supports internal pattern audio LPCM 2CH 48 96 192KHz LPCM5 1 48 96 kHz LPCM7 1 48 96KHz Code XA1 306 44 HDMI over CAT5E 5 Extender One of the Professional series of HDMI Cat5 3D Extenders The PE121L features 3D IR and HDMI Ethernet Channel Pass Thru all via twin CAT5E cable Fully compatible with Blu Ray 3D and featuring IR pass through this is a great problem solver and it s compact size makes it very unobtrusive Features e Uncompressed 1080p HDMI over Cat5e 6 7 e Local HDMI output on Sender unit e Full range IR Pass Thru receiver amp emitter included e CEC Pass thru allows one remote control to sync TV and AV devices e Support HDMI v1 4 3D video format Blu Ray player and 3D TV e Support v1 4 HDMI Ethernet Channel Specifications e HDMI Spec v1 4 Compliant e DVI Spec v1 0 Compliant e HDCP Spec v1 2 Compliant e Video Format Up to 1080p 3D Uncompressed Video e Audio Format Up to 7 1 Channel DTS HD Master Audio Dolby TrueHD e HDMI Source Input Port 1 Port e HDMI Display Output Port 1 Port e LINK Connector RJ 45 Shielded x2 e HDMI Ethernet Channel Pass Thru Supported Code PE121L 1 54 99 Email your order to us at sales keene co uk HDMI Over Long Distances HDMII over CAT5 These products make a very affordable method
96. n www keene co uk HDMI Over Long Distances HDMI over IP Network As well as HDMI over dedicated Cat5 cable we can now offer transmitter receiver systems that will send HDMI signals via an IP computer network Amazingly they place very little load on your network bandwidth and operate as a true multicast that is to say one transmitter can drive multiple receivers with no extra network load They really are extremely simple to operate just plug and play with no in depth networking capability required They also provide The newly updated PB5000Plus units now provide IR feedback and RS232 control and deliver stunning Ultra High Quality 1080p HDMI Video broadcast over IP network full IR feedback allowing remote control of source equipment A flexible scalable low cost solution to distributing HD signals to multiple displays They can be used in Extender Mode connect the Sender to the Receiver by CAT5e 6 7 cable directly or Broadcaster Mode Sender to Receiver via LAN for one Sender to many Receivers PB5000P Via an inexpensive Gigabit Ethernet network switch the PB5000P can support Point to Point Point to Many Broadcasting and Multi Casting which multiple video sources with PB5000 Senders video streaming to multiple TVs Displays Projectors with PB5000 Receiver Multi casting can be done by Managed Gigabit Switch with 802 1Q VLAN function which provide control remotely and allows more video source senders to be inte
97. ncluded 19 99 19 99 Code KAOC Code KACO optical to coaxial coaxial to optical e Supports uncompressed digital LPCM 7 1 5 1 or 2 channels amp compressed digital Bitstream through HDMI input and output ports e Supports LPCM 7 1 5 1 or 2 channels output through multi channel output ports e Supports digital Dolby 5 1 2 and LPCM 2 channel output through Optical Toslink Code AU11SA e1 29 41 Features e Supports Coaxial or Optical digital audio SPDIF signals e Supports Stereo and Multichannel digital audio LPCM DTS Dolby Digital Dolby Digital Plus e Supports sample rate up to 96kHz Dual transmission 1 x Coaxial and 1 x Optical Signals can be extended over single CAT5e CAT6 up to 150m Power 5V 1A DC US EU standards CE FCC UL certified Dimension PU 304RX 55mm W x 85mm D x 22mm H PU 304TX 55mm W x 85mm D x 22mm H DAC Digital to Analogue audio with USB interface DAC with USB audio interface and headphone amplifier The most affordable and effective way to upgrade any CD DVD player computer games console or network device to high end sound quality The DAC has one optical one coaxial and one USB inputs for up to three digital sources DAC is the ideal convertor for music lovers seeking an excellent value upgrade to 24 bit advanced HD high definition audio 39 00 Code DAC Code PU304 1 1 5 44 HDMI Audio Embedder with built in Repeater The AU 11CA Audio
98. ne co uk 4 99 Bluetooth Audio Adaptor A fantastic gadget simply pair it with any Bluetooth audio source plug the output into any device with an auxiliary input and listen to internet radio or the music stored on your smartphone or tablet PC on your audio system wirelessly Suitable for all Bluetooth enabled sound sources such as iPhone Android phone iPad etc Works with all audio installations iPhone dock or radio CD player with aux in line in or mp3 link connection Supports A2DP Stereo Bluetooth for music in CD quality It also works great with the Keene KLABKITD previous page Specifications e Support multiple pair Up to 8 devices e Range Up to 10 metres free field Interface audio output 3 5mm male jack e Power Mini USB or battery e Battery Li ion 140mAh Stand by time up to 140 hours Working time up to 6 hours e Energy Saving Automatic switch off if no connection within ten minutes Code Sound Level Meter Digital Display How well set up is your home cinema system How low does your subwoofer go Find out for certain with a sound level meter Great value for money this gives you the accuracy you need to fine tune your system e Built in microphone e Seven selectable frequency ranges e Phono output for connection to external equipment FAST amp SLOW response settings Weighting selector A for Human ear bias or C for full frequency range Peak l
99. need IStrIDUTION system y an electronic box of tricks in the middle Although we get This is a great value HDMI over Cat cable distribution system SUPpOrts 24 36bit deep colour video formats asked many times it is sadly impossible to simply chop an that allows you to mix and match between stand alone and Supports LPCM LPCM7 1 DSD DVD audio Dolby AC3 HDMI plug off and solder on a scart cable in its place OK wall plate receivers All types support 3D and provide DTS5 1 DTS HD DTS master audio Dolby Digital Plus it s not impossible but it definitely wouldn t work There Reeda i and Dolby True HD audio formats are plenty of convertors that will perform this task and also ss e Can be used with stand alone or wall plate Spade Weiter ode Vea The sender unit takes a single HDMI HDMI receivers I want to go from an HDMI to a scart input and transmits it via twin runs e Requires two Cat5e 6 STP FTP cables per receiver This is possible but trickier depending upon what the HDMI of CAT cable to up to four outputs not supplied source is HDMI from a commercial source such as a DVD up to a distance of 30 0m without player or set top box will almost certainly contain HDCP e Power required for the transmitter unit only copy protection see info panel and cannot be converted back to analogue If the source is non HDCP eg camcorder then there are several boxes to perform this task signal loss This unit receives HDMI signals i Specific
100. ng The microscope is Ideally suited for examining objects such as coins stamps rocks relics insects plants gems circuit boards various materials skin and many other objects Also you can examine specimen slides at low and high powers Specifications e Handheld Digital Microscope Powered by a 2 0 USB Cable e Digital Camera built in 2MP for Snapshot Images and Videos e Power 10x to 40x and 150x e LED Illumination Code CDM 45 00 Email your order to us at sales keene co uk
101. nslucent finish flush wall plate 624 99 Code IRSP Panel Mount IR Receivers An Infra Red panel mount receiver designed to be used with any Keene IR Distribution amplifier This receiver can be fitted into the cabinet casing or studded wall e Requires a 16mm diameter hole e Overall thread length 44mm e Maximum material thickness 38mm e Visible bezel diameter 30mm e Connection is via a 1m cable to 3 5mm jack plug Code IRPMR black 29 99 Code IRPIMRW white 29 99 Code IRPMRB brass 34 99 Code IRPMRC chrome 34 99 A IR Anywhere Matrix SKY Digital Remote Control Wired Eye Global 10 Link RF Adaptor Link Magic Eye An ingenious device this utilises the ability of a Sky receiver This device plugs into the multi pin socket found on the Sky digital satellite systems have two RF aerial outputs to be controlled via its 2nd RF input and provides a hard back of Sky HD boxes that have no RF2 output It provides The 2nd RF output can be run to a remote television wired in cabinet control solution Instead of affixing an RF output for RF based viewing at multiple TV locations typically a bedroom or kitchen to allow you to view an IR emitter directly to the receiver front panel you can It also enables Infra Red control via the TV Link Sky Eye Sky Once you ve done this you can then easily control now connect the IR output from the IRBKIT IRCM or IR Magic Eye type IR controllers that use the RF2 socket the digi
102. nto the device s fascia by means of a small sticky pad A small red LED blinks each time an IR signal is emitted as confirmation that the command has been sent Dimensions of emitter L x 10mm x W 10mm x D 5mm Fitted with a 3 metre cable lt an 9 49 IR Dual Blinking Wand The single jack plug drives two IR emitter wands The emitters are extremely tiny just 9mm across and are supplied with double sided adhesive pads to affix directly to the equipment fascia The emitters actually flash red as the IR signal is emitted giving visual confirmation that the IR signal was received and transmitted correctly A vao 9 99 IR Low Power Wand Can be attached directly to the equipment facia or will work up to 4 metres away Even when attached directly the equipment will still respond to external IR signals For use with the RBKIT low power output sockets e cow 9499 IR High Power Wand Only for use with the Keene IRBKIT in the High Power output socket Provides a very high output IR signal that will operate equipment up to 10 metres away If placed inside a cabinet the signal will usually reflect to operate several items of equipment without requiring any other emitters It can also be used with other Keene IR Distribution amplifers or the IRBKIT low power socket but will then only perform as a low power emitter Not suitable for one to one operation Code IRHPW a 99 Side Firing Wand A short range emitter for dir
103. ome Theater installation allow to send to TV and Amp with Max Video and Audio signal e HDMI Specification 1 3b Compliant e Support HDMI 36 bit Deep Color amp x v Color wide color gamut e Supports 480i 480p 576i 576p 720p 1080i and 1080p resolution e Audio support Dolby TrueHD amp DTS HD lossless 7 1 digital surround amp Lip Sync e Plug and play Installs in seconds e Easy operating with IR Remote HDMI Matrix Switchers Value Range These are true HDMI Matrix switchbox that routes any of the four HDMI inputs to any or all of the outputs Input routing by front panel push button or IR remote control with LED confirmation Matrix switching allows for maximum versatility for integrated systems Superb value for money BeOne Media Panel New from Coosis a stylish Multimedia AV Wallplate ideal for Hotels Apartments Meeting rooms etc There are front inputs for Composite amp Audio S video HDMI VGA amp 3 5mm stereo audio and these are all automatically converted to a single HDMI output The input is automatically switched to an active signal and will automatically revert back to the previous when the current becomes inactive Touch sensitive switches in the backlit panel can be used to override the auto input switching if required There is a USB port which can operate in one of two modes it can be set to work as a charge output 5v 1A or it can be routed through to the display USB if this suppor
104. or HDMI Onput 1 HD AV Link RJ 45 Port 1 Ethernet RJ 45 Port 3 RS232c 1 IR Receiver Port 1 e Product Dimension 220x83x27mm Express Install Multi room HDMI System Express Installation Kit 4 x 4 HDBaseT LITE Matrix with PU 514L RX Receivers This 4 by 4 HDMI HDBaseT Lite Matrix Express Installation Kit has been developed as a robust and cost effective solution at the heart of any four zone multi room environment Supplied complete with a HDBaseT Lite Matrix plus four PU 514L RX receivers the kit enables an installer to easily and confidently configure a 4 zone multi room AV system using HDBaseT Lite technology and distribute content throughout the system over a Single CAT5e 6 7 cable infrastructure The Express Install Kit supports the transmission of video resolutions up to 1080p Full HD and 1920x1200 60Hz multi channel digital audio and control via IR RS 232 or Web GUI Telnet IP from four high definition sources to four HDBaseT outputs over a single CAT5e 6 7 cable up to 60m for each output HDBaseT HDMI over single CAT6 transmitter and receiver The PU 107 can send and receive a pure digital HDMI signal over a single CAT6 cable allowing HD Audio amp deep colour support The PU 44XL KIT is supplied with 4x PU 514L RX receivers which utilise the 2 way IR control capabilities of the matrix Use the IP control feature to enable users to access and control the matrix remotely and also allow addition
105. ote this unit will not scale the signal the output resolution is determined by the resolution of the input signal please check your display is compatible with the resolution produced Code HDMIVGAP 59 99 Composite s video to Component or RGB A handy compact unit that will convert either Composite or S Video to RGsB or YUV via 3 phono socket connectors It automatically recognises any world standard input NTSC 3 58 4 43 PAL PAL M PALN amp Secam The Output format is selectable between RGB and YCbCr Specifications e Input 1x CV 1X SV e Output 3 phono RGsB or YUV e Power Supply 5V DC 350mA adaptor supplied e Dimensions 145 x 90 x 32 mm Code CPVSRGB cf 4 2 1 RGB to S Video Convertor RGB is a great method of sending video with picture resolution as good as s video and vastly superior to a std composite signal The problem is not everything can accept an RGB signal and often composite is your only option Well here s another problem solved This Box can convert an RGB scart output into S video plus audio Code RGB2S 59 99 S video to Composite Video Bi directional Convertor An amazing little gadget with an S video socket at one end and a composite phono socket at the other Containing a special filter network it works fully bi directionally It won t magically increase picture resolution but it will make life easier when wiring up say an AV amp that supports composite
106. ounting Fits screens with VESA mounting patterns 75mm x 75mm and 100mm x 100mm Easy tilt adjustment 17 10 CLIPLOGIC cable management included Simple hook on installation with all mounting hardware included Features 3 swivel points 180 at wall 360 at central pivot point 240 at interface Screen size 10 23 Max Weight 15kg 331lbs 360 rotation for easy screen levelling and to allow screen to be mounted in landscape or portrait style Security locking screws amp Allen key provided for secure installation Features OWLS On Wall Levelling System Colour Black ore BT7513B 27 a 84 Projector Trolley Designed for use with projectors but may also be used as a portable lectern Supplied with braked castors and optional levelling feet for extra stability Supplied with safety rails and safety strap for secure installation e Adjustable height with castors 785mm 1265mm 30 9 49 8 Adjustable height with feet 730mm 1230mm 29 7 48 4 e Platform dimensions 290mm x 360mm 11 4 14 2 Adjustable tilt 20 degrees Inner pole diameter 35mm 1 4 Outer pole diameter 42mm 1 6 Easy to assemble e Max Weight 25kg 55lbs 79 99 79 99 black silver Code BT890B Code BT890 BT8505 Flat Screen Display Trolley Designed for flat screens 30 to 50 127cm 40kg Suitable for Non VESA patterns up to 755 29 7 x 4
107. ouplers 1U without tie bar 179 00 Code PP13 Code PP14 16 Port Switchcraft Blank 1U Code BPP32 15pin HD outlet plates Standard size white wall single outlet plate with a 15pin HD female connector The rear of the plate also has a 15pin female socket making It easy to connect to premade 15pin a HD cables Code HCP21 white 9 99 Code HCP215S brushed steel 15 99 15 pin QC plate The HCP21 15 pin HD wall outlet plate is also now available in a quick connect solderless version This QC series plate has both an internal 15 pin HD female socket as well as screw terminals meaning you use pre made cables or make solderless connections to bare wire ends The terminal blocks are rising clamp style 6A rated and will accept cables up to 1mm sq amp Code HCP21QC 13 99 15 pin QC plate steel The HCP21QC is also available in a brushed steel finish Code HCP21QCS 199 00 Code BPP16 69 00 32 Port Switchcraft Blank 2U 80 68 19 AV Rack Panels Rugged 19 inch AV patch panels powder coated black 24 x F Socket couplers 1U Code PP1 69 99 12 Pairs Speaker Posts 1U Code PP2 89 99 12 Pairs RCA Phono Sockets 1U Code PP3 99 99 8 Sets Composite amp Stereo 1U Code PP4 99 99 22 x BNC Couplers 1U Code PP5 99 99 14 x Speakon Sockets 1U Code PP6 99 99 14 x 3 Pin XLR Female 1U 109 99 Code PP8 109 99 Brush Opening 1U Code PP9
108. overload protection 51 95 32 95 Code AA625 Sender amp Receiver Pair Code AA625R Additional Receiver Features e Designed to allow the use of two pairs of speakers with one amplifier e Speaker selector switch to play either pair of speakers or both at the same time e Suitable for loudspeakers from 4ohms to 160hms e Screw terminals for strong connection and minimal loss e Strong stylish metal casing e Accepts loudspeaker cable up to 2 5mm diameter e 150 watts RMS per channel rating Code BT12 e1 3 99 Spring clip terminals e Designed for 4 16 ohms speakers e Wiring Gauge 14 to 22 gauge e Input 1 x stereo e Output 8 x stereo e Power per channel 100W max e Dimensions 432 x 125 x 55mm e Weight 2 08kg TE ar ee Code 8WLS 29 00 2x4 Speaker Matrix Switch with Volume Control This matrix switcher for stereo amplifiers has 2 inputs and 4 outputs Any of the inputs may be routed to any of the outputs or the same input may be routed to all outputs or any combination Simply connect the output of the amplifiers to the inputs these inputs can then be routed to four different stereo speaker sets in four different locations each speaker set can be individually activated via the push buttons on the front of the box and individual volume controls Enables four pairs of speakers to be connected to two separate amplifiers Features e Heavy duty push buttons e Built in overload protection e Designe
109. pensate for lip sync errors Features and Specifications e HDMI v1 1 HDCP 1 1 Compliant e Maximum O Resolutions WUXGA and 1080p e Accepts 480i or 576i SDTV input e Automatically Detects Input Resolution e 50 60Hz Frame Rate Conversion Code 1TVS626 e1 71 81 HDMI to VGA amp Audio Convertor HDMI in to VGA and decoded analogue audio out This unit will take in HDMI and give out VGA with analogue stereo audio HDMI 1 3 compatible Supported input resolutions 4801 P 576i P 720P 10801 P Specifications e Video Input HDMI socket e Audio Output 3 5mm jack socket e Video Output 15pinHD VGA connector e Dimensions WxHxD 84 x 28 x 76mm e Power 5V 2A UK mains adaptor supplied Code CHUHV 59 99 Find product information and data sheets on www keene co uk HDMI Cables Aavara High Definition HDMI Cables These are top specification Hi Definition AV Cables fully supporting all of the latest HDMI specifications including 3D 4K ARC Audio Return Channel HEC HDMI Ethernet Channel The construction features pure gold 24K plated end shell and connector with a protective braided cable sheath a ee ee voce ET E eS eS 180 Degree swivel Plug High quality High Speed with Ethernet HDMI cable Each plug has 180 degree swivel to make It easier to connect to awkward sockets Specifications e Gold plated terminals with moulded strain relief Code HDHD141S 1m version 14 99
110. pread 360 The speakers are splash proof and fine for use in the bathroom Because of the wireless technology you can place the speakers wherever you want Because of the optional battery power you don t even need a socket e Use your iPod radio or anything with a headphone socket as the source Easy to install and to use automatic frequency tuning and maintenance because of Auto Tuning and PLL function Code SA352U 7 2 x 00 Speaker Outlet Wall Plates Twin 4mm Binding Posts Wall outlet plate with 2 pairs of a colour coded gold plated binding posts Fits a standard one gang patress Solder tag connection on rear Code HCP20 11 99 Single 4mm Binding Posts Wall outlet plate with a single pair of colour coded gold plated binding posts Fits a standard one gang patress Solder tag connection on rear Code HCP5 9 99 Single Spring Clip Wall outlet plate with a single pair of loudspeaker spring clip terminals Fits a standard one gang patress Solder tag connection on rear Code HCP16 3 99 Twin Spring Clip Wall outlet plate with two pairsof A loudspeaker spring clip terminals i Fits a standard one gang patress Solder tag connection on rear z Code HCP17 5 99 Twin 4mm Socket Wall outlet plate with two pairs of banana type 4mm loudspeaker sockets Fits a standard one gang patress Solder tag connection on rear Email your order to us at sales kee
111. puts from one HDMI input ideal for viewing on multiple displays The units can also be cascaded together in a pyramid network to provide a one to many solution Please note If the max resolutions of your displays are different the EDID functionality will detect all the connected displays EDID information and auto match the output resolution to the lower one For example if one display supports 720P resolution and the rest support 1080P the signal will be lowered to 720p for all displays Blu ray 3D Compatible Code HDC12 1 input to 2 outputs 34 99 Code HDC14 1 input to 4 outputs 74 99 Code HDC18 1 input to 8 outputs 114 99 VGA amp Audio Cat 5 Extender System Specifications e Cable between units CAT5 CAT5e and CAT6 e Max distance 50 metres VGA input port HDB15 female x 1 Audio input port Stereo jack female x 1 VGA output port HDB15 female x 2 e Audio output ports Stereo jack female for local unit x 2 Mono jack female for remote unit Enables you to transmit VGA signals up to 150M 500ft away with resolution up to 1024 x 768 It features common mode noise suppression circuit for superb VGA quality via inexpensive unshielded twisted pair CAT5 cables The Local unit duplicates the input signal for local use and transmits the VGA signal to a Remote unit The Remote unit broadcasts the signal to two VGA outputs The units also distribute audio mono at remote location Ideal
112. r Bit stream Specifications Input Port 1 x HDMI HDMI Sample Frequency Up to 192 kHz Optical Sample Frequency Up to 48 kHz Output Ports 1 x HDMI 1 x Optical 1 x analogue L R HDMI Audio Format PCM2 5 1 7 1 Dolby 5 1 DTS 5 1 DD D True HD DTS HD Optical Audio Format PCM2 Dolby 5 1 DTS 5 1 L R Audio Format LPCM2 Code HDMIAE 59 a 99 Audio Only Source to HDMI Bridge The AU 11HB Audio Source to HDMI Bridge is designed integrate audio only sources into HDMI video distribution systems It will accept digital optical or analogue L R Stereo audio signals and output them over HDMI This clever device also adds a blue screen video feed into the HDMI signal path so that any HDMI AV receiver or display will accept the audio signal for sound reproduction It allows audio from any source to be easily integrated into a HDMI system very useful when distributing via an HDMI or HDBaseT matrix great for systems such as SONOS etc Code AU11HB e1 64 64 HDMI Audio Amplifier This is effectively an HDMI switcher that allow you to embed or de embed audio from multiple sources It delivers a powerful 30W per channel and has IP connectivity for easy ipad tablet control Well worth a look for any AV multi room installation Features e 30W per channel digital stereo Amplifier e Inputs HDMI x 2 1 x L R Stereo audio 1 x Optical 1 x Digital Co Ax 1 x 3 5mm Stereo e Outputs 1 x HDMI 1 x Optical 1 x Digital Co
113. r and a switchable high pass filter to reduce unwanted low frequency rumble It has a standard hot shoe mount and can also be attached to a boom arm or tripod The connection is via a 3 5mm stereo mini jack Studio recording quality Rugged fibre reinforced ABS construction 9 V battery operation not included Custom designed integral wind shield Condenser Microphone Low noise circuitry Low handling noise Integral hot shoe mount Full 10 year warranty registration required ut tT Code RVM 74 99 Code RVMDEAL mic plus Pro windshield 92 00 Rode VideoMic Pro compact Shotgun Microphone The R DE VideoMic Pro raises the bar set by the original RODE VideoMic by combining broadcast quality audio with an ultra compact and lightweight ergonomic design Incorporating new features specific to high end video the VMP also evolves many of the features that have made the VideoMic so successful Noise transference has been significantly reduced using both a revised more elegant shock mounting system and a lightweight premium cable e Broadcast recording quality condenser microphone e Compact design only 150mm 6 length e Ultra lightweight only 85g 30z e 9V battery powered with up to 70 hours battery life alkaline e Integrated shock mounting e Integrated foam windshield e 3 5mm stereo mini jack output dual mono e Two step High Pass Filter flat 80Hz e Three position level control 10dB O 20dB
114. r channel deep colour e Supports HDCP pass through Code SW104 39 99 Email your order to us at sales keene co uk HDMI Matrix Switchers 4X1 COMPOSITE OR S VIDEO amp AUDIO SWITCH MX 3141 series 4x1 Routing Switchers are extremely wide bandwidth high performance products that meet the most demanding requirements for signal routing Video as well as Audio are routed Video Bandwidth Is flat 3db to beyond 300MHz ensuring these switchers will provide an output identical to the source signals The MX3141CSVA switches NTSC or PAL Composite or S Video plus Stereo Analog Audio This unit features RS 232 control capability and is shipped with an IR remote control a rack mount kit plus an AC power adapter Features and Specifications e Professional Grade High Performance Switcher e Video Bandwidth Greater than 300MHz e NTSC and PAL Television Standards e Inputs 4x composite video on RCA S Video on mini 4 pin din and Stereo Audio on RCA e Output 1 x composite video on RCA S Video on mini 4 pin din and Stereo Audio on RCA e Push Button and IR Inputs Selection e Rugged Metal Case e Locking DC Power Connector for Security Code MX3141CSVA 80 67 AAVARA PS124 HDMI 1080p Splitter 1 to 4 The Aavara PS124 is an HDMI v1 3b 1080p distribution hub that sends the same HDMI video output to four HDMI HDTV digital screens It is a flexible solution to integrate multiple displays in signage video wall or demo
115. roadcast scenarios or wherever professional quality audio is required in a discreet portable format without the complication and expense of additional wireless equipment With the smartLav the user simply mounts the microphone on the talent connects it to a smartphone or tablet headset jack and records via the RODE Rec app for iOS or any other audio app of their choice By employing a high quality omni directional condenser capsule the smartLav picks up sound equally from all around the microphone allowing for versatility when mounting and ensuring a high degree of user friendly operation A foam pop shield is supplied to minimise wind noise and vocal plosives hard b t and p sounds as well as a durable mounting clip with in built cable management The smartLav Is compatible with any audio app that accepts input from the headset connection however it has been designed to pair perfectly with RODE s RODE Rec app for Apple iOS devices RODE Rec turns the user s iOS device into a fully featured field recorder with a wide range of equalisation presets to suit various recording situations in addition to professional editing functions and the ability to publish to SoundCloud and Dropbox direct from the app 34 99 Code SMARTLAV Rode NT1A Vocal Pack The World s Quietest Studio Condenser Microphone The RODE NT1 A has become an industry standard delivering the warmth extended dynamic range clarity
116. s Thru function allows video sources to be controlled via IR remote control from TV Display which may be located some distance away CHDBT gt Code PE3D4K100A 5 3 8 a 2 8 Features e Transmit up to 100M Uncompress 1080p HDMI signal via CAT5e 6 7 Cables e 10 2Gbps Ulrat High Performance Transmission support up to 4Kx2K Resolution e HDMI V1 4 3D Video Format Support for 3D blu ray and TV connection at distance e 36 bit Deep Color amp CEC Pass Thru support e POC Power Over CAT5 support Receiver no Power Adapter needed e Ethernet Extend support 3 x 100Mbps Ethernet RJ 45 switch at both Sender amp Receiver e Full range 20 60Khz IR Pass Thru allows to control Video Source from receiver side e Two Way RS 232 Control communication for Display or video Source control at remote site e Hassle free plug n play install in sec e HD Audio Video Internet IR amp RS232 Power all in ONE SINGLE Cable Link Target Applications e HDMI Spec 1 4 Compatible e DVI Spec 1 0 Compliant e HDCP Spec 1 1 Compliant e Data Speed Up to 10 2Gbps e Ethernet Network Data 100 10 Base TX e Ethernet Port 3x RJ 45 Ports at Sender amp Receiver e RS 232 connector DB 9 Stanard Female Connector Bi direction transfer amp up to 192 000 bps e IR Pass Thru Signal frequency 20 60Khz e Sender Connector HDMI Input 1 HD AV Link RJ 45 Port 1 Ethernet RJ 45 Port 3 RS232c 1 IR Emiiter Port 1 DC 24V Input 1 e Receiver Connect
117. s 16 9 16 10 expand amp subtitle Control is by front panel or supplied IR remote Great for connecting legacy equipment to an HDMI switchbox and for simplifying your connections Inputs SCART CVBS y c PAL NTSC RGB 480i 576i s video PAL 576i NTSC 480i HDMI Output 1920 x 1080 1680 x 1050 1360 x 768 1280 x 720 with digital audio Power 5v DC 2000mA UK adaptor supplied Dimensions 170 x 110 x 32mm Code HDUSPRO 59 99 Component VGA amp Audio to VGA Convertor Switch The Coosis HD GAMING PRO Component to VGA 1080 Convertor Model HG PRO provides an easy way to convert analogue component YPbPr signal to VGA up to 1920X1200 resolution It enables you to carry on using previous models of monitors CRT projectors digital projector or plasma displays which are not Component inputs compliant Easily connect devices such as PS3 XBOX360 Wii satellite boxes or Blue ray players etc Being aware of the stretched image caused by varied screen aspect ratio 4 3 16 9 amp Full screen this convertor is integrated with image aspect ratio correction to recover 1 1 pixel matching It also provides a VGA input to take the signals from PC laptop or other VGA sources and mirror to VGA output and audio output when in stand by for easy monitoring so you don t need to keep switching cables VGA to HDMI Convertor Allows you to display the image from your computer to a monitor or large TV It will conver
118. s high bit rate HBR audio e Input and Output HDMI cable length can run up to 10m at 1080p 8bit resolution e Low power consumption e Support built in audio EDID switch of LPCM2 5 1 7 1 or Bitstream e Supports 3D signals Specification e Inputs 1 x HDMI e Outputs 1 x HDMI 1 x Optical Toslink 2 x Analogue Audio L R RCA e Power 5V 1 2A DC US EU standards CE FCC UL certified e Dimensions 90mm W x 85mm D x 35mm H Code AU11CD e1 22 31 Email your order to us at sales keene co uk HDMI Audio Extractor The HDMI Audio Extractor is a device that allows you to extract audio signals from your HDMI source When connecting with a TV or display you dont always get great audio or in the case of a display no audio at all so with this Audio Extractor you can take your original HDMI audio signal and convert it to Digital Toslink or analogue L R audio What this means is that you can output your audio signal to external speakers or extend your audio signal the HDMI Audio Extractor is the perfect choice Features Compliant with HDMI 1 3 HDCP 1 2 and DVI 1 0 Supports HDMI Sample Rates up to 192 kHz Supports Optical Sample Rate up to 48 kHz Supports TMDS clock frequency rate 225MHz Supports high bit rate HBR audio HDMI cable distance testing showed that with 1080p 8bit resolution the input amp output can run up to 15 meters Low power consumption Supports built in audio EDID switch of LPCM2 5 1 7 1 o
119. shelf Features e Distribute HDMI signal to 4 HDMI displays e Daisy Chain up to 3 layers 256 displays 4 x 8 x 8 e CEC Consumer Electronic Control pass thru Output Channel 1 e Support 36 bit Deep Color up to 1080p e Audio support Dolby TrueHD amp DTS HD e Support 7 1 digital surround amp Lip Sync e Plug and play Installs in seconds Specification e HDMI Spec 1 3b Compliant e DVI Spec 1 0 Compliant e HDCP Spec 1 2 Compliant e CEC Allows 1 TV remote to sync interoperability between display projector and HDMI AV devices connected e Dimension 245 W x 107 D x 27 H mm Code PS124 e1 1 9 00 Aavara PM4X2 1080p HDMI MATRIX 4X2 The Aavara PM4X2 1080p HDMI 1 3b MATRIX 4X2 is a switcher splitter hub that offers you maximum convenience in HDMI signal distribution when you have multiple HDMI sources and displays to connect together Each of the Four HDMI sources can be directed to any one of the two HDMI outputs so two displays projector can show same source or two different sources simultaneously It is compliant with Blu ray DVD players and satellite set top boxes to any HDMI compatible display Sources are accessible at any time to any display when operating with the IR remote PM4X2 4x2 matrix switching allows maximum versatility for integrated systems Features e Allows you to select same HDMI source or two different sources output to two displays separately e Max Video Output function for H
120. splays by Easy Web Interface Configuration e Optional PoE support upon request PB5000P 524 54 394 62 Sender Receiver pair Additional receiver HDMI over Single Coaxial Extender Yet another really useful way to get HDMI from one place to another the PCE122 can send ultra high quality HDMI v1 3 over a single coaxial cable RG6 or RG59 It can send full HD 1080P up to 120M or 720P up to 230M both with full 7 1 channel audio The conversion is fully digital HDMI to SDI and back again with no additional compression and gives you crystal clear HD at long distances The PCE122 also contains a built in 1 to 2 Coaxial Splitter to drive two separate receivers and each receiver has a loop through to daisy chain additional receivers as required Cables are connected via BNC for a secure vibration resistant connection PCE122 with IR feedback Code PCE122IR transmitter amp receiver pair with IR 542 61 Code PCE122RIR additional receiver with IR 315 70 Specifications e 120M HDMI 1080p video and 7 1channel audio one cable transmission with Ultra High Quality Video e Features World Leading Single Coaxial Transmission designed to simplify Installation e 1080p 120M 720p 230M long distance Ultra High Quality Video with 7 1 channels surround sound transmission e Up to 7 1 channels audio Dolby Digital Dolby TruHD DTS HD pass thru e Built in 1 to 2 Coaxial Splitter in Sender and One Coaxial Casc
121. styles of receivers and emitter wands can easily be incorporated The IR output can also be connected to the input of another Keene IR Distribution amp If required direct IR feed IR output control of AV into other Other IP RS232 X10 lighting equipment IR distribution devices matrix and appliances systems switchers The Keene IR Anywhere family of products give you easy internet control of any Infra Red RS232 or contact closure products There are many ways to use them for example Use two modules with one set to act as IR receiver and one to act as an IR transmitter and connect them both to your network Aim your remote at the receiver and it will convert the signal to packet data send that data to the other module which will decode the data and retransmit the IR as originally received You can do this whether the receiver is in the next room or on the other side of the world Compatible with a variety of Apps such as Demopad Mote TouchSquid TouchControl Reymote and many more you can use your smartphone or tablet to control your AV equipment from anywhere you have an internet connection Or access the device from any browser on any internet capable device using the built in web pages Use the KIRACC for smartphone control of contact closure operated blinds curtains garage doors Install the IR Commander Matrix and enjoy selective routable control of multiple devices The possibilities are endless Please see
122. t your PC s VGA video and audio into one complete HDMI signal Features e Converts VGA video and audio into one HDMI signal e Signalling rates up to 1 65Gbps e HDCP Compliant e Supports up to 1080p resolution e Supports 480i 576i amp 1080i resolution e Supports VGA resolutions up to 1280 x 1024 60 75Hz e Outputs HDMI Code VGAHDMI 59 00 HDMI to SDI Convertor Mini Convertor HDMI to SDI is ideal for converting from HDMI devices to SDI video with the choice to embed SDI audio from HDMI AES EBU or balanced analogue audio inputs Now you can add SDI outputs to cameras with HDMI connections or add if your computer supports HDMI compatibility via DVI to HDMI adapters then you can use for adding SDI outputs to computers Code HDGPRO 69 a 99 Component to HDMI Convertor Component and Audio input to HDMI output Specifications e HDMI to SDI Analogue Conversion e Auto Switching SD and HD e New 3 Gb s SDI Technology e Built in AES EBU or Analogue Audio This unit will take in a Component video signal plus analogue stereo audio and convert the output to digital HDMI HDMI 1 3 compatible Supported Component input resolutions 4801 P 576i P 720P 1080i P Specifications e Video input 3 x RCA phono e Audio input 2 x RCA phono e Video Output HDMI socket Code CONVMHS c2 1 9 a 2 G e Dimensions WxHxD 84 x 28 x 76mm e Power 5V 2A UK mains adaptor supplied Code CHUCH 59 99 Also avail
123. tactile moisture resistant front panel switches LED s for status and confirmation e Flush mount or surface mount 25mm depth Code HDMI Solutions 14 19 20 AV Plates amp Panels 21 Audio Microphones t Control Solutions 22 28 D SLR 29 AV Accessories 30 31 32 34 36 For more new products and bargains visit KLAB In Wall Amplifiers You quite often want to listen to some music in other rooms in your house such as kitchens bedrooms bathrooms amp studies The problem usually is space You can fit flush mount loudspeakers into ceilings and walls without much difficulty but that still leaves the problem of where to put the amplifier To solve this problem Keene designed the KLAB series of in wall audio amplifiers built into a standard two gang pattress These will fit flush to the wall or can be surface mounted if preferred and deliver 2 x 20W RMS of amplification That s a proper true 20W RMS of power as well unlike most of the ridiculous maximum or PMPO ratings you commonly see quoted a true 20W RMS delivers enough power to satisfy even the most party inclined teenager The recommended power supply for the KLAB series is rated at 15v DC a 4 0 The KLAB amplifiers can also be powered from a 12v DC supply for easy use in boats caravans amp motor homes although the maximum output power will be slightly reduced There are three models in the range Analogue Digital and Bluetooth KLAB Analogue Models The
124. tcher Splitter Value Range The HDMI Amplifier Switch Splitter is an HDMI splitter with the ability to switch between 3 inputs to display to 2 outputs It distributes the input into the two identical outputs simultaneously Each output can achieve a long distance transmission of a HDMI signal of up to 15 metres Two or more products may be cascaded to achieve a larger distribution and longer length Operation is by front push button control or by supplied IR remote Features Switch easily between any three HDMI sources to two displays Support HDMI1 3b Support highest video resolution 1080p Support 225MHz 2 25Gbps per channel 7 5Gbps all channel bandwidth Support 12bit per channel 36bit all channel deep colour Support HDCP Note Devices with DVI output are not supported due to the lack of signal control Code HDMI32S 49 z 99 HDMI four way auto switch The HD SW104 is an intelligent HDMI amplified 4 port switch It allows four HDMI devices to be switched to one HD Monitor Projector or HD TV The intelligent function will automatically switch between HDMI sources as and when they are plugged in removed or turned off plus there is also touch button and IR remote control HDMI Automatic 2 1 Line Powered Switchboxes The smallest HDMI auto selector on the market This is a very neat switchbox two inputs to one output They re line powered so you don t need to find room for another mains adaptor and they
125. the full HD capability The transmitter converts the HDMI signal into a balanced differential signal and the receiver converts it back into a conventional HDMI signal again It uses two runs of CAT5E or CAT6 cable and allows for full auto adjustment of feedback and equalisation with no user intervention required This model also provides IR feedback along the same CAT5 cables for control of source equipment from the viewing area Long HDMI cables are expensive and unwieldy whereas CAT5E cable is cheap and flexible making it much more suitable for long distance runs This pair of units can send HDMI at full 1080p up to 50m and can also be used for DVI D signals with a suitable adaptor such as the KA169 Features e Watch and operate your HD Content elsewhere on your TV e Watch films look at photographs and listen to music from for example your Media Centre PC Blu Ray player game console set top box or hard disk recorder on a different TV projection screen in perfect HD quality e Operate your connected A V equipment remotely via the infrared return signal e Wired signal transmission up to 100 metres e Optimum price quality ratio as a result of using CAT5e CAT6 cabling e Retention of Full HD 1080p image and sound quality for up to 60 metres e Free from interruption due to solid metal interference free housing Code MEG61 NEW LOW PRICE Code GV821 266 36 Also available GV811 A compact model for in room
126. tion Screen Paint has much better contrast and brightness than that of a plain white wall It has the same quality as a professional projection screen On top of that you always have exactly the right screen format for your specific situation No more struggling to set up a conventional projector screen No more bulky ceiling or wall fixture Invisible when you are not using It How it works BaseCoat ContrastBooster The foundation of the screen is the BaseCoat which also determines the contrast level Based on an easy to use checklist you determine the right amount of ContrastBooster to be used This ContrastBooster sets the grey level of the BaseCoat for the screen area Mighty Brighty offers a range from matt white to ultra grey high contrast All in the same package TopCoat BrightnessBooster After applying the BaseCoat a TopCoat is required Using the same handy checklist you determine the amount of BrightnessBooster which sets the gain value for the TopCoat Mighty Brighty offers a gain range trom 0 9 up to 1 4 depending on the amount of light the projector emits and some other criteria MagneBorder The unique MagneBorder is optionally available This border greatly heightens the contrast perception of images on the screen A magnetic paint must be applied prior to the BaseCoat and TopCoat The magnetic borders can be easily placed and removed from the projection area When the MagneBorder is removed all you see
127. tput Fully scaleable video inputs include HDMI DVI via the HDMI connector Analog RGB YPbPr via an HD 15 Analog YPbPr or 4801 5761 YUV Component via three RCA YC and Composite Video It handles I O Resolutions up to 1080p and WUXGA Both digital and analog audio processing is supported and audio delays of up to 150ms can be introduced to insure lip sync Five Analog Stereo and a SPDIF Coaxial Digital Audio input can be selected for embedding into the HDMI output A separate Coaxial Digital Audio output Is also provided Advanced features such as 3D Motion Adaptive De Interlacing 3D Noise Reduction and 8 bit triple ADC PLL technology combine to provide extremely high quality signal conversion The HDMI I O is HDCP Compliant An OSD On Screen Display menu makes the 1T VS 658 easy to set up Control Is via front panel joystick and buttons Infrared Remote via optional IRC 5 or RS 232 interface Features HDMI Output Resolutions to WUXGA and 1080p Inputs HDMI RGB YPbPr YUV YC S Video CV Both Analog and Digital Audio Capable Audio Delay for Lip Sync Corrections 3D Motion Adaptive De Interlace amp Noise Reduction 3 2 Pull Down w 2 2 Pull Down Recovery Infrared Remote Control optional IRC 5 Specifications Video Inputs HDMI DVI Compatible 1x via HDMI Connector Analog RGBHV YPbPr 1x via HD 15 Connector Analog YUV Component 1x via 3x RCA Connectors YC S Video 1x via 4 pin Mini Din Composite Video 1x via RCA Conne
128. tre run Code DST 329 99 Headrest Mount The headrest mount enables the camcorder to be mounted onto a car s headrest It is fully adjustable for the different widths of headrest The camcorder attaches to a ball mount so the camera can be set to the required position You get a great view from the drivers prospective or it can be used to video inside the vehicle Only suitable for headrests with twin posts Ideal forMini DV cams amp all types of handheld Camcorders up to 2kg 58 29 Code CHM Mini Motion Cam The Hague Mini Motion Cam is a handheld stabilizing system which is ideal for small lightweight camcorders or cameras between 0 3kg and 0 8kg in weight e Supports up to 1 25kg with additional weights e Ideal camera weight 0 3kg to 0 8kg e Quick amp simple to set up e Smooth camera movement e Eliminates camera shake The camcorder fits directly onto the stabilizer with adjustment for moving the camera forward and back for balancing y Ee 75 00 e E ee E Code MMC and data sheets on www keene co uk Rode Podcaster Broadcast USB Microphone Seamless integration was the idea and it was obtained by creating a studio dynamic microphone with unparalleled A D convertors so that the microphone can be plugged into any computer with no in out boxes no expensive computer pre amps just a USB cable The Podcaster offers an end address configuration the clarity of RODE s tai
129. trol The module can switch on or off an appliance of up to 13 amps ideal for kettles fans heaters lamps etc For appliances and low energy lamps Code AM12U Power Ethernet Sockets The PE200AV Power Ethernet Sockets embed all the electronics inside a standard wall power socket The technology allows the use of the existing mains cables as a way to transmit high speed data and environmental services throughout the building without the cost and disruption of installing additional cabling No rewiring required Simple to install by any electrician simply replace a power socket with an Power Ethernet Socket Reduces infrastructure costs by using existing mains cabling throughout the building Minimises installation disruption no need to lift floor panels and replacing a socket is quick and easy All Ethernet points automatically mesh together into a secure network without needing a patch panel and Ethernet switch Much cheaper to replace existing power sockets with PE Sockets than to add additional structured cables nad i 79 00 156 00 300 00 Code PE200AV each for two for four X10 Lamp Module Gives you instant X10 control of any plug in lamp Plugs into a 13 amp socket and will switch on off lamps plugged into the module s standard 3 pin socket In addition it can dim brighten standard tungsten or halogen filament bulbs only NOT fluorescent Load 40W minimum 300W max in
130. ts media playback F P j h iat 4 Specifications e HDCP Spec 1 3b Compliant e DVI Spec 1 0 Compliant e HDCP Spec 1 2 Compliant e MATRIX 4X2 Transmit same source or two different sources simultaneously e Operation temperature 5 C to 35 C e Storage temperature 20 C to 60 C e Humidity Range 5 to90 RH e Signal Rate 6 75Gbps e Power Consumption 5W e Video Bandwidth 225 MHz e Single Link Range Supports 480i 480p 576i 576p 720p 10801 and 1080p resolution e Cable Length 5M In and Out respectively e Dimension 245 W x 107 D x 27 H mm fa g Code PM4X2 1 93 37 Features e Switch easily between any four HDMI sources e Distributes any of the four inputs to any or any combination of the two HDMI output displays e Support HDMI 1 3b e Support highest video resolution 1080p e Support 225MHz 2 25Gbps per channel 6 75Gbps all channel bandwidth e Support 12bit per channel 36bit all channel deep colour e Support HDCP e External 5V DC 2A Power Supply included e Easy operating with IR Remote Note Devices with DVI output are not supported due to the lack of signal control Four inputs to two outputs Code HD42M 84 99 Four inputs to Four outputs Code HD44M 299 99 The LAN RJ45 and PHONE RJ11 two inputs are pass through Cut out size 376 x 78mm x 76mm deep gt l nR i Te a m Ei k i i i i eet 4 ae Find product information and data sheets o
131. up to 2 5mm dia Connect in line between amplifier and speaker Se Code rock Do 99 Find product information and data sheets on www keene co uk Wireless Audio Sender A Sender Receiver pair designed to transmit audio wirelessly around your house Take the line or headphone output from your PC TV or music system and sonnect it the Sender then connect the line output from the receiver back into the remote amplifer in the room you want to listen in The sender and receiver will automatically pair so there s nothing to configure Additional receivers can be added for a one to many solution 2 Way Speaker Selector Switch The B Tech BT12 Allows a second pair of loudspeakers to be connected to your amplifier with switch select for either pair or both screw terminal connections suitable for cable up to 2 5mm diameter 8 Way Speaker Selector Switch This switcher unit allows the distribution of a stereo amplifier Simply connect the speaker output of an amplifier to the box this output can then be distributed to up to eight different stereo speaker sets in eight different locations each speaker set can be individually activated via the push buttons on the front of the box Ideally suited for buildings where an independent sound control is required for different rooms or zones Enables eight pairs of speakers to be connected to a single stereo amplifier Specifications e Heavy duty push buttons e Built in
132. ut switching with input s last delay restored Automatic optical to coax coax to optical conversion 4 digital audio inputs 2 digital audio outputs optical and coax Adjustable display brightness Discrete IR commands for integration with learning remotes No effect on audio quality thanks to bit perfect reproduction 4x1 Digital Audio Switch The AU D41 Optical Audio Switcher has four optical inputs and one optical output This device allows users with multiple optical sources connection for one output display All signal are bypassed without delay The device has last memory function and IR remote control Features e 4 input digital optical audio switcher Optical sampling rate supports up to 192 kHz Up to 24bit resolutions Low power consumption PCM2 AC3 5 1 Dolby 5 1 amp DTS 5 1 pass through Amplifies Optical Toslink output extending another 5 metres Supplied with IR remote control Coaxial Toslink to L R Stereo Audio Convertor This neat audio convertor will convert the selected switched signal either coaxial RCA or optical Toslink and convert the digital signal to analogue audio with a left and right output Specifications e Input 1 x Toslink Fibre Optic amp 1 Coaxial RCA e Outputs 2 x RCA s Left and Right Code L Code Harmony Headphone Amplifier The Harmony Headphone Amplifier takes line level input and provides stereo headphone amplification It can be controlled
133. uts for cable entry on four sides and bottom 1 99 Code NPB CAT5E 6 Patch Leads Product description e Colour Grey e Connectors 2 x RJ45 e Applications 10BaseT a a 100BaseTX amp Gigabit Ethernet i e Crossed connections NO Code UTPO5 L 0 5m grey 1 49 Code UTP10 L 1 0m grey 1 49 Code UTP20 L 2 0m grey 1 99 Code UTP30 L 3 0m grey 3 99 Code UTP50 L 5 0m grey 4 99 Code UTP100 L 10 0m grey 8 49 Code UTP200 L 20 0m grey 10 99 Code UTP300 L 30 0m grey 19 99 Find product information and data sheets on www keene co uk HDMI Switchboxes CONNECT 420 5 1 HDMI Switch 3D e Only one cable to your TV screen Switch between the HDMI devices connected e Suitable for connecting 5 HDMI sources to your TV simultaneously You just need 1 HDMI input and you never have to switch cables again e Suitable for Full HD 1080p and all 3D formats e With built in repeater and equalizer for correcting any possible loss of signal so you can connect up to 15 metres of HDMI cable to the output e Switches automatically and or with remote control e Solid metal casing Code C420 81 2 00 CONNECT 310 3 1 HDMI Switch 3D e Only one cable to your TV screen Switch between the HDMI devices connected e Suitable for connecting 3 HDMI sources to your TV simultaneously You just need 1 HDMI input and you never have to switch cables again e For connecting a game console like PlayStation and Xbox Blu
134. via IR remote or front panel push buttons It can be used for any purpose where line stereo level audio is required to be amplified to headphone level It is particularly suited to TV viewing applications where one person listening via headphones can set their own personal volume without affecting the normal audio output for anyone viewing normally Specifications e Audio Input 2 x RCA phono e Audio output 1 x 3 5mm stereo jack socket e Power 12V DC 200mA UK mains adaptor supplied e Dimensions 90 x 76 x 44mm e Weight 170g exc cables amp supply Code Find product information and data sheets on www keene co uk Analogue Audio Lip Sync Corrector This analogue stereo Lip Sync Corrector is a small device for delaying audio signal to overcome audio sync issues The AU D18 Lip Sync corrector is able to adjust the timing to the display amplifier so that users may received both video and audio in sync No more annoying sound mismatch The Lip SyncCorrector is easy to use with a simple setup and an affordable unit for sound delaying Features e Lip Sync corrector with adjustable delay between 0 amp 300ms e Sample Rates 48 kHz e Analogue to analogue signal bypass e Low power consumption Specifications e Inputs 2 x Analogue Audio L R stereo e Outputs 2 x Analogue Audio L R stereo e Power 5V 1A DC e Dimensions 45 D x 45 W x 25 H mm Code AUD18 63 25 AU 11SA Audience HDMI Audio De Embedder Rep
135. y fraction of the many analogue and digital cables we are able to supply Please call or visit www keene co uk for more details 3 BNC TO 3 PHONO RGB COMPONENT CABLE High quality three BNC plugs to three RCA phono plugs Gold plated connections Application RGsB or component video Code SBB201 1 0M 29 999 Code SBB202 2 0M 34 99 Code SBB204 5 0M 39 99 Code SBB205 10 0M 49 99 Find product information and data sheets on www keene co uk AV Supports Centre Speaker Mount Centre Speaker Wall Mount with Adjustable Arms Designed for loudspeakers up to 15kg 33lbs e Ideal for centre channel speakers DVD players and other AV equipment Allows speaker to be positioned for optimum esoteric performance e Easy adjustment of arm depth Simple installation with all mounting hardware included Specifications e Maximum Weight 15kg 33lbs Code BT15 black 12 99 Atlas Loudspeaker Floor Stands e Designed for loudspeakers up to 50kg 110lbs e Sound isolating loudspeaker floor stands e Fillable columns for superior dampening e Top and bottom isolation spikes provided e Supplied in Pairs e Available in different heights Specification e Max Weight 50kg 110lbs e Top plate dimensions 190mm 7 5 x 190mm 7 5 e Base plate dimensions 240mm 9 5 x 240mm 9 5 e Max weight of speaker 50kg 110lbs Code BT604 40cm height 49 99 Code BT606 60cm height 54 99 Code BT608 80cm height

NEW Products & Special Offers

Contents

Download Pdf Manuals

Related Search

Related Contents

NEW Products &amp; Special Offers

Contents

Download Pdf Manuals

Related Search

Related Contents

NEW Products & Special Offers