Home
1.4 Extension Port Assignment - Syd-Com
Contents
1. 278 Programming Error Messages 11 1 Error Messages EXXXX Error Message Error Code Description E9002 Page length must be 4 lines more than Skip Perforation The difference of Page Length and Skip Perforation must be more than 4 lines E9003 Trunk or extension card duplicated Under Power Failure Transfer a trunk card or an extension card can be specified only once E9004 Assign both trunk card and extension card Cannot assign just trunk card or just extension card Both must be assigned as a pair under Power Failure Transfer E9005 Time or date format error The invalid value of time or date is entered E9006 Invalid System Programming password Please assign the 4 through 7 digit System Programming password of alphanumeric characters E9007 Invalid User Programming password Please assign the 4 through 7 digit User Programming password consisting of 0 9 E9008 Invalid Walking COS password Please assign the 4 through 7 digit Walking COS password consisting of 0 9 E9009 DDI DID MSN number duplicated Each DDI DID MSN number in 9 1 Number Transformation screen must have a unique number E9010 Number of DDI dial must be equal to or less than 16 digits Cannot specify the number 992 999 as the Beginning Entry No because Number of Registrations is set by 10 entries increments and the number of available entries are limited to 1000 E9011 Beginn
2. Parameter Message Lamp Default No Value Range 1 Yes 2 No Description Function Assigns whether an SLT with MESSAGE lamp can receive the message waiting indication or not Assignable when an SLT with Message lamp is interfaced by an ESLC card Reference e 1 17 Display Features F G Message Waiting Parameter Preferred Line Outgoing Default Prime Line ICM PDN Value Range 1 No Line 2 Idle Line 3 Prime Line ICM PDN 4 Prime Line CO Description Function Specifies the line to which the extension is connected automatically when it goes off hook for making a call Reference e 4 1 1 Initial Settings U M Parameter Preferred Line Outgoing Key No Default Blank Value Range 1 24 Description Function Specifies the CO button number to which the extension is connected when it goes off hook to make a call This assignment is required when Prime Line CO is specified in Preferred Line Outgoing programming Reference e 4 1 1 Initial Settings U M Line 4 3 Extension Line Parameter Preferred Line Incoming Default Ringing Line Value Range 1 No Line 2 Ringing Line 3 Prime Line ICM PDN 4 Prime Line CO Description Function Specifies the line to which the extension is connected when it goes off hook to answer a call Reference e 4 1 1 Initial Settings U M Parameter Preferred Line Incoming Key No Default Blank Value Range 1 24 Descript
3. Parameter 20 Off hook Monitor Default Enable Value Range 1 Enable 2 Disable Description Function Enables or disables Off hook Monitor feature on a system wide basis This feature allows a PT user on a handset call to let other people around him her monitor the call by pressing the SP PHONE button Note e This setting applies to the following PT extensions only KX T7531 KX T7533 KX T7536 Reference e 1 12 Conversation Features F G Off Hook Monitor e 2 4 7 Letting Other People Listen to the Conversation Off Hook Monitor KX T7531 KX T7533 and KX T7536 only U M 2 8 3 System Option 3 4 Used to assign system option parameters No 21 N0 30 2 7 System Option 3 4 M E 21 Illegal Humber DISA 26 Pressing CO key operation in CO talking Send reorder tone C Transferred to IRNA destination Disconnect Hold 22 Illegal Number DDLDID _ __ 27 Message Waiting lamp pattern Send reorder tone C Transferred to IRNA destination oe r 23 Illegal Number TIE 28 Trunk hunting mode Send reorder tone Forced Loop Detection Transferred to IRNA destination 24 Sending dial tone to TIE trunk __ 29 Card CODEC f Enable Disable paw C plaw 25 Pressing DSS key operation in CO talking 30 Net CODEC C Disconnect Hold C plaw Alaw 2 7 System Option 3 4 OK apply Cancet Help 86 System 2
4. 3 3 Paging Group x OK Apply Cancel Help Parameter Paging Group No Default 1 Value Range 1 16 Description Function Specifies the Paging Group which you are going to programme Reference e 1 14 Paging Features F G Paging e 2 6 1 Paging U M Parameter Extension Group No Default Paging Group No 1 only No 1 1 No 2 128 Others None Value Range None 1 128 Description Function Specifies the Extension Group which you are going to assign to the Paging Group Up to 24 Extension Groups per Paging Group can be assigned Reference e 1 14 Paging Features F G Paging 124 Group 3 5 DIL 1 N Group 35 DIL 1 N Group Used to programme a list of up to 96 DIL 1 N Groups You can assign up to 72 extensions and or Extension Groups extensions simultaneo per DIL 1 N Group so that an incoming CO call rings multiple usly 3 4 DILI N Group EEK FDH Mailbox Ho rowno ME 7 onerar Destinations 7 Ho DH Ringing Type Ho DH Ringing Type Ho DH Ringing Type meane sC femea sE Ll emean 2 19 Immediate x 20 m Immediate 2 immediate 28 E Immediate x 29 Immediate x af J l Immediate z 3 4 DIL1 H Group x oK Apply Cancel Help Parameter Group No Default 1 Value Range 1 96 Description Function Specifies the DIL 1 N Group which you are going to programme Reference 1 5 Attended Features F G Direct In Lines DIL
5. Mailbox No Same as the extension number CO Key CO 01 Loop CO Others Not Stored PF Key Not Stored Initial Display Selection Caller ID Message Lamp No Preferred Line Outgoing Prime Line ICM PDN Preferred Line Outgoing Key No Blank Preferred Line Incoming Ringing Line Preferred Line Incoming Key No Blank LCS Setting Status Inactive LCS Setting Operation Mode Hands free LCS Setting Recording Mode Stop Rec LCS Setting LCS Password Blank Call Log Incoming Overwrite Mode Yes Call Log Incoming Lock Password Blank Pickup Dialing Mode Disable Pickup Dialing Dial Display only Data Line Mode No Call Waiting Tone Type Tone 1 Call Pickup Deny Disable Language English Station Lock Password Blank CLIP COLP Number Public Blank CLIP COLP Number Private Blank Charge Limit 0 JOG Dial Speed Normal ISDN Bearer Mode Automatic 300 Default Values 4 3 2 Flexible CO Key Assignment Program Default Key Type CO 01 Loop CO Others Not Stored 4 3 3 Flexible PF Key Assignment for PT Program Default Key Type Not Stored 4 4 DSS Console 4 4 1 DSS Console Copy Program Default Paired Extension DSS Console 1 8 Port No Display only DSS Console 1 8 Model T7540 DSS Key Not Stored PF Key Not Stored 4 4 2 Flexible DSS Key Assignment Prog
6. Parameter Table No Default 1 Value Range 1 32 Description Function Specifies the UCD Time Table which you are going to programme Reference 3 3 Extension Group P G Features 211 5 13 UCD Time Table Parameter Command Sequence 1 16 Default Value Range Description Function Reference Command No 1 of all tables 1T Others None None S1 S8 IT 4T TR RET OFF The following commands are provided to construct a UCD Time Table procedure lt Commands list and their functions gt None Skips to the next sequence S1 S8 OGM 1 8 is sent to the caller if available If not wait until OGM 1 8 becomes available 1T 4T Callers are put in the waiting queue for N 1 4 x 8 seconds while hearing the ringback tone or music on hold TR Transfers a call to the Overflow destination RET Returns to the first step of the sequence OFF Disconnects the call compulsorily Note e Ifan unavailable OGM S 1 8 is assigned in the UCD Time Table it will be ignored 3 3 Extension Group P G 212 Features 5 14 Charge 5 14 Charge Used to assign parameters for the Charge Fee Management feature 5 14 Charge lel ea Charge Display on LCD Charge by SMDR Mir 1 l Meter Charge Charge Verification ID Code 4 7Digits l Tenant 1 Tenant 2 Tenant 3 Tenant 4 Tenant 5 Tenant 6 Tenant 7 Tenant
7. Parameter 5 Limited call duration Default Both calls Value Range 1 Outgoing call only 2 Both calls Description Function Limited call duration is a system programmable feature that disconnects an outside call when a specified timer expires A warning tone is sent to the extension user 15 seconds 10 seconds and 5 seconds before the time limit Both calls means incoming and outgoing calls Note e This setting applies to the extension on which Time Limit of Outside Calls is enabled by COS programming Reference e 1 3 System Features F G Limited Call Duration Parameter 6 Transfer recall destination Default Originating extension Value Range 1 Originating extension 2 Operator Description Function Specifies whether Transfer Recall occurs at the transfer originating extension or at Operator Group extensions if the call both inside and outside transferred to an extension is not answered within a specified period of time Reference e 1 11 Transferring Features F G Call Transfer 80 System 2 8 System Option Parameter 7 Checking dial by toll restriction Default Check Value Range 1 No check Disable 2 Check Enable Description Function Specifies whether or not the system checks the user dialled X and during Toll Restriction procedure Note e This assignment is required for certain Central Offices CO to prevent toll fraud Some Central Offices ignore the use
8. Call from AA port to AA port Allow Sending out Follow on ID after FWD Enable Sending out Follow on ID after IRNA Disable 5 11 Caller ID Modification Program Default Local Call Area Code Blank Local Call Digits to delete No 1 3 Others 0 Local Call Number to be added Blank Long Distance Call Digits to delete 0 Long Distance Call Number to be added 1 Default Values 305 5 12 Caller ID Registration Program Default Tenant No 1 Entry No 0001 0010 Name Blank Number Blank 5 13 UCD Time Table Program Default Table No 1 Command Sequence 1 16 Command No 1 of all tables 1T Others None 5 14 Charge Program Default Charge Display on LCD Meter Charge by SMDR Meter Charge Verification ID Code Tenant 1 8 1234 Rate 1 0 Currency SP NL JT DM G Currency Display Position Tail Treatment of Charge Limit Alarm Tone Meter Count up by Answer Detection Disable 5 15 Hotel Program Default Title Header 3 lines Check Out Sheet Header Start Line 1 Header Start Column 1 Data Start Line 4 Data Start Column 1 306 Default Values Program Default Language English 6 Toll Restriction 6 1 Toll Restriction 6 2 TRS Deny Code Program Default TRS Level 6 Entry No 001 020 Dial Blank SP NL JT XXXXXXX G Level
9. 3 3 Extension Group Used to assign various parameters for up to 128 1 128 Extension Groups Which parameters apply to your Extension Group Please refer to the table on Page 115 and Page 116 Note By default the Group Type of Group No 126 is VM No 127 is AA and No 128 is Operator 3 2 Extension Group Overow Seting Destination Day YUU Mode fe Enable vas inner Disable UCU Setting amp Enable Disable lime Table No t Prat K Spel stor AWD Ho Answer gt Enable Dis Call Pio 1 Auto LOGOUT Mode Disable 4 oc gt E CO Cail n u intercept Routing 2 u 7 a E SUPETMISOT EXTEN SIO 2 Betz tension Call a LOGIN Monitor G Enable te Disable Singe El UCD Call Waiting fe Enable Disable s2emension Grou z ox poly came nem 114 Group 3 3 Extension Group Applicability of Parameters to Group Types Group Type Parameter None Ter Cir Ring Ope VM AA UCD ue v v v v v v v v PDN v v v v v v v v Tenant No Vv Vv v Vv v v Vv v Overflow Setting Vv v Vv v v v Destination Day Night Overflow Setting Timer v FWD DND Mode Vv v v Extension Call Hunting Vv Y Operator Setting Ringing v Type Operator Setting Call Vv Priority UCD Setting Time Table v No UCD Setting FWD No Vv Answer UCD Setting Auto v LOGOUT Mode UCD Setting Supervisor Vv Extension UCD Setting LOGIN v Monitor
10. Key Type Additional Parameters Description ONE TOUCH Dial Specifies the telephone number or feature access number up to 24 digits consisting of 0 9 x P S or F Note P Pause S Secret Dialling F Hook Flash Name Specifies the name for One Touch dial up to 10 characters consisting of 0 9 A Z a z or the following marks X 3 lt gt amp SS Dial Specifies the telephone number or feature access number up to 24 digits consisting of 0 9 x P S or F Note P Pause S Secret Dialling F Hook Flash Parameter Key Type Default Value Range Description Function Reference Not Stored Please refer to Description Function Not Stored Key Type is not assigned ONE TOUCH One Touch Dial button FWD DND Call Forwarding Do Not Disturb button SAVE Saved Number Redial button ACCOUNT Account Code entry button CONF Conference button ANSWER Answer button RELEASE Release button SS ISDN Service button 4 1 2 Customising the Buttons U M Line 165 4 4 DSS Console 4 4 DSS Console Used to assign the paired extension for a DSS Direct Station Selection Console and the usage of DSS and PF buttons 4 3 DSS Console Paretenin DSS Console 1 r DSS Console 5 Port No pow DSS Key PF Key Port No ss 155 Key PF Rey Model Leony Arev moder ee Er DSS Console 2 DSS Co
11. 268 Maintenance Section I Programming Error Messages Programming Error Messages 269 11 1 Error Messages EXXXX 11 1 Error Messages EXXXX Error Message Error Code Description E0000 System error Error code XXX A system error occurred Please inform your distributor how the error was generated and what the error code was E0001 Cannot create temporary file There is insufficient free space on your hard disk or this software is not installed correctly E0002 Illegal password The password entered while making the connection didn t correspond to the one that had already been registered E0003 System error ID XX An error code was returned by the Windows System Library The error code was XX Please inform your distributor how the error was generated and what the error code was E0004 The file XX doesn t exist Tried to open the data file XX that doesn t exist E0005 Illegal programming version Tried to open the data file that was made in the newer software version of PC programming than one being used at present E0006 Communication error A communication error occurred between your PC and the PBX Or the port parameters of your PC do not match the port parameters of the PBX E0007 Communication error of the modem XX XX stands for the result code that was received from the modem E0008 Cannot open COM port The COM port of your PC is being used
12. Error Code Description E4022 Cannot assign PDN key as Prime Line CO Please assign key number except for PDN key when the outgoing or incoming preferred line is set to Prime Line CO E4023 Illegal trunk group number Please assign the trunk group number 1 48 on Group CO key E4024 DN or FDN must be entered to assign the type of key You must enter the DN or FDN when you assign key type DSS Phantom SDN VTR 2WAY REC and 2WAY TRN Each key needs following directory number as DN or FDN DSS Extension directory number which is in existence Phantom Floating directory number which is registered in 5 2 Phantom Extension screen SDN Primary directory number PDN of the DN mode extension VTR 2WAY REC TRN Extension directory number which is assigned as VPS E4025 PHANTOM key duplicated Two phantom keys cannot have the same phantom FDN E4026 Please enter CO key number assigned to S CO G CO L CO or SDN key The CO key number which is assigned to Single CO Group CO Loop CO or SDN key should be entered when Prime Line CO is specified in Preferred Line Outgoing Incoming programming E4027 Doorphone destination duplicated Doorphone destinations extensions must be unique for Day mode settings and Night mode settings However an extension used for Day can be used for Night E4028 Converted digits exceed the limit Total number of converted digits should be
13. 6 1 Toll Restriction Used to assign TRS Toll Restriction Deny Codes and TRS Exception Codes a TD500 Maintenance Console mming 220 Toll Restriction 6 2 TRS Deny Code 6 2 TRS Deny Code Used to programme a list of up to 400 TRS Toll Restriction Deny Codes telephone numbers that extension users cannot dial 6 1 TRS Deny Code TRS Level Entry No 001 020 gt See sn A A Ho Dial Max 10 Digits Ld Ss Ld 6 Ld O Oo el 0 Parameter TRS Level Default 6 Value Range 2 6 Description Function Specifies a TRS toll restriction level Reference e 1 6 Originating Features F G Toll Restriction Parameter Entry No Default 001 020 Value Range 001 400 in 20 entries increments Description Function Specifies a unit of 20 TRS Deny Codes which apply to the TRS level selected Reference e 1 6 Originating Features F G Toll Restriction Toll Restriction 221 6 2 TRS Deny Code Parameter Dial Default Blank SP NL JT XXXXXXX G Level 2 only Value Range Up to 10 digits consisting of 0 9 X or Description Function Specifies the leading 10 digits of the toll restricted telephone numbers Note e X can be used as a wild card character which substitutes any digit in its position Reference e 1 6 Originating Features F G Toll Restriction 222 Toll Restriction 6 3 TRS Exception Co
14. Service A unique code dialling digits up to 16 digits can be assigned to each command Parameter Leave Message Default H Value Range Up to 16 digits consisting of 0 9 or H Description Function Specifies the Leave Message command This command is transmitted to a VM port if a call is forwarded or intercepted and rerouted to the VM port Reference e 1 3 System Features F G Integration VPS Parameter Get Message Default H Value Range Up to 16 digits consisting of 0 9 x or H Description Function Specifies the Get Message command This command is transmitted to a VM port when the message receiver presses the MESSAGE button to retrieve a voice message Reference e 1 3 System Features F G Integration VPS 200 Features 5 10 VPS Integration Parameter AA Service Default 8 Value Range Up to 16 digits consisting of 0 9 or H Description Function Specifies the AA Automated Attendant Service command If AA Service is set to Start by System Programming this command is sent to a VM port if an incoming CO call is answered by the VM port Reference e 1 3 System Features F G Integration VPS Parameter VM Service Default 6 Value Range Up to 16 digits consisting of 0 9 X or H Description Function Specifies the VM Voice Mail Service command This command is transmitted preceding the Get Message command above This is effective to switch to a VM port
15. 189 5 6 Account Code 5 6 Account Code Used to programme a list of up to 1000 account codes which are used to identify incoming and outgoing CO calls for accounting and billing purposes Tenant No E etry Wo gt RR ae Hone M 11 None None gt 12 None gt 13 None gt 14 None gt 16 None gt a7 None gt 18 Pa ene ea 1 2 3 4 5 None M 15 6 7 8 9 5 5 Account Code None gt 19 None gt 10 None gt 20 None gt x oK Apply Cancel Help i Parameter Tenant No Default 1 Value Range 1 8 Description Function Specifies the tenant to which a list of Account Codes is assigned Required when Tenant Service is employed Reference e 1 3 System Features F G Tenant Service 2 2 Tenant P G Parameter Entry No Default 0001 0020 Value Range 0001 1000 in 20 codes increments Description Function Specifies the entry number of the Account code which you are going to programme Reference None 190 Features 5 6 Account Code Parameter Code Default Blank Value Range Up to 10 digits consisting of 0 9 Description Function Specifies the account codes Reference e 1 3 System Features F G Account Code Entry e 2 2 5 Calling without Restrictions U M Parameter TRS Level Default None Value Range None 1 6 Description Function Sp
16. CPC Signal OUT Detection Disable ELCOT card Enable E1 DR2 card CPC Signal OUT Detection Detection Time ELCOT card 32ms SP None NL JT G CPC Signal OUT Detection Detection Time E1 DR2 card 160 ms CPC Signal IN Detection Enable E1 DR2 ELCOT card SP Disable ELCOT card Enable E1 DR2 card NL JT G CPC Signal IN Detection Detection Time ELCOT card 32ms SP None NL JT CPC Signal IN Detection Detection Time E1 160 ms DR2 card Start Signal Type Wink Wink Signal Time out 1024 ms Reverse Signal Detection Disable SP NL JT Enable G Digits to receive DDI DID 4 El DR2 card 7 BRI PRI30 card SP NL JT 4 EI DR2 card 8 BRI PRI30 card G TIE Line Type 4 wires TIE Line Sensitivity IN 0 dB TIE Line Sensitivity OUT 0 dB TIE Line Sending TIE Caller ID No TIE Line TIE to CO Security Mode No DDI DID TIE Digits to delete 0 DDI DID TIE Number to be added Blank Answer Wait Timer None 4 3 Extension Line 4 3 1 Extension Line Copy Program Default Card No Port No 1 Group No Display only DN Default Values 299 Program Default Name Blank COS No Primary 1 COS No Secondary 1
17. Programming J as 5 248 Maintenance 10 2 External Modem 1 2 10 2 External Modem 1 2 The system supports an external modem plugged into the RS 232C port for remote system administration 10 1 External Modem 1 2 Bee Manual Initialization Command Max 80 Characters Automatic Initialization Command Max 80 Characters AT amp FOODEOV150 1X0 amp D0 ox amy comeu uep Parameter Manual Initialization Command 1 5 Default All Blank Value Range Up to 80 characters consisting of 0 9 A Z a z or the following marks x lt gt 7 amp Description Function Specifies Modem Manual Initialisation Command Reference e 1 3 System Features F G External Modem Control e 2 11 1 Controlling the External Modem External Modem Control U M Maintenance 249 10 2 External Modem 1 2 Parameter Automatic Initialization Command Default AT amp FOQOEOV 1S0 1X0 amp DO Value Range Up to 80 characters consisting of 0 9 A Z a z or the following marks x 3 lt gt 7 amp Description Function Specifies Modem Automatic Initialisation Command Reference e 1 3 System Features F G External Modem Control e 2 11 1 Controlling the External Modem External Modem Control U M Note A hardware flow control cannot be done by the communication port of KX TD500 Therefore the hardware flow control of your modem must be di
18. 10 6 System Parameters 10 6 System Parameters Used to assign various system parameters 10 4 System Parameters Password 47 Digits User Programming Walking COS System Programming Sie e m Serial Interface Port PROG SMDR NI Le Parity Hone Hone ra I n NL Code CR LF Word Length 8 bits 8 bits NI Le i Stop Bit 1 bit bit Baud Rate 10 4 System Parameters r Remote FDH Max 4 Digits Dhrerer Parameter Password System Programming Default 1234 Value Range 4 7 digits of alphanumeric characters Description Function Specifies the password required for entering System Programming mode and Maintenance from a Personal Computer Reference e 3 5 Operational Mode I M e 4 Utility I M Parameter Password User Programming Default 1234 Value Range 4 7 digits consisting of 0 9 Description Function Specifies the password required for entering the User Programming mode Reference e 1 2 System Administration F G User Programming e 4 3 Customising Your System User Programming U M Maintenance 10 6 System Parameters Parameter Password Walking COS Default 1234 Value Range 4 7 digits consisting of 0 9 Description Function Specifies the password required for using the Walking COS feature Reference e 1 6 Originating Features F G Walking COS e 2 2 5 Calling without Restrictions
19. 23 G 5 5th Hundred Block Extension 14 SP NL JT 24 G 6 6th Hundred Block Extension 20 SP NL JT 30 G 7 7th Hundred Block Extension 21 SP NL JT 31 G 8 8th Hundred Block Extension 22 SP NL JT 32 G 9 9th Hundred Block Extension 23 SP NL JT 33 G 10 10th Hundred Block Extension 24 SP NL JT 34 G 11 16 11th Hundred Block Extension 16th Blank 17 Operator Call 0 SP 9 NL JT G 18 Local CO Line Access ARS 9 SP 0 NL JT G 19 Trunk Group Access 8 20 Speed Dialing System 21 Speed Dialing Station 3 SP NL JT 6 G 22 Speed Dialing Station Programming 30 SP NL JT 60 G 23 Doorphone Call 31 SP NL JT 68 G 24 External Paging 32 SP NL JT 64 G 25 External Paging Answer TAFAS Answer 42 SP NL JT 44 G 26 Station Paging 33 SP NL JT 63 G 27 Station Paging Answer 43 28 CO Call Pickup 4 29 Group Call Pickup 40 30 Directed Call Pickup 41 31 Hold 50 32 Hold Retrieve Station 51 33 Hold Retrieve Trunk 53 34 Redial Default Values 289 Program Default 35 Call Park Call Park Retrieve 52 36 Account Code 49 37 Door Open 55 38 External Feature Access 6 SP NL JT 66 G 39 Station Program Clear 790 40 Message Waiting Set
20. 4 times NL 15 times JT Value Range 0 30 times Description Function Specifies the number of times Automatic Redial is repeated Automatic Redialling of the last dialled number saved number or call log number is done up to the specified number of times Reference e 1 7 Dialling Features F G Redial Automatic Parameter Door Opener Time Default 5s Value Range 0 10s Description Function Specifies the door opening duration Note e The DPH card is not available in some countries Reference e 1 3 System Features F G 2 5 2 System Timer 2 2 Door Opener 2 8 1 If a Doorphone Door Opener is Connected U M 71 2 5 System Timer 2 4 System Timer 2 2 r Timed Reminder Ringing Time 30 240 s s BEIE r DISA Automated Attendant Time 1 5 s f js r Call Parking Recall Time 0 1800 s DISA IRNA Time 5 240 s m TIE Inter digit Time 3 30 s nk Intercept Timer after OGM Cots C5hs DISA Prolong Time 0 7 min p min r OBI Route Request Time 1 60 s m T DISA Delayed Answer Time 0 6 rings fh ring s OAI Predichve Make Call Time 1 60 5 s Timed Reminder Arrive Count 1 5 times B time s r Timed Reminder Arrive Wait Time 20 240 s 2 4 System Timer 2 2 Parameter Timed Reminder Ringing Time Default 30s Value Range 30 240 s Description Function Specifies the length of ringing time in sec
21. Cancel Call Back 70 41 OGM Playback Record 36 SP NL JT 712 G 42 Call FWD Do Not Disturb Set Cancel 710 43 Dial Call Pickup Deny Set Cancel 720 44 Data Line Security Set Cancel 730 45 Call Waiting Set Cancel 731 46 Executive Busy Override Deny Set Cancel 733 47 Pickup Dialing Program Set Cancel 74 48 Absent Message Set Cancel 750 49 Timed Reminder Confirm Set Cancel 761 SP NL JT 76 G 50 Station Lock Set Cancel 762 SP NL JT 77 G 51 Night Mode Set Cancel 78 52 Parallel Telephone Mode 39 53 External BGM On Off 35 54 Live Call Screening 799 55 Call Log Incoming Overwrite Mode 56 SP NL JT 54 G 56 Call Log Incoming Log Lock 57 SP NL JT 59 G 57 Timed Reminder Remote 7 58 Login Logout 45 59 Automatic Callback Busy Cancel 46 60 Walking COS 47 61 MODEM Control 791 SP NL JT Blank G 62 MCID 737 63 70 Quick dial 1 Quick dial 8 Blank 71 Reserved Reserved for future use Blank 72 Remote DND 722 290 Default Values Program Default 73 Remote FWD Cancel Once 723 74 Trunk Route Control 724 75 UCD Monitor Mode 725 76 TIE Line Access 77 SP NL JT Blank G 77 92 Other PBX 01 Other PBX 16 Blank 93 Paging Deny Set Cancel 721 94 Trunk Busy out 726 95 Walking Stat
22. Parameter System Speed Dial TRS Level Override Default No check SP NL JT Check G Value Range 1 Check Enable 2 No check Disable Description Function Enables or disables Toll Restriction Override for System Speed Dial Numbers feature If enabled Check all extension users in the tenant can make System Speed Dialling calls without toll restriction Reference e 1 6 Originating Features F G Toll Restriction Override for System Speed Dialling Parameter System Speed Dialing Entries Max Default Tenant 1 1000 Tenant 2 1000 Tenant 3 8 0 Value Range 0 1000 in 20 codes increments Description Function Specifies the maximum number of Speed Dialling codes available for each tenant Note e Up to 2000 Speed Dialling codes can be shared among tenants under the restriction of up to 1000 codes per tenant Reference 5 2 System Speed Dialling P G 37 2 2 Tenant Parameter Manager Extension DN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the extension number for the Manager Reference e 1 3 System Features F G Manager Extension e 3 Operator Manager Operation U M Parameter External Paging Tone Default Check Value Range 1 Check Enable 2 No check Disable Description Function If checked confirmation tone is emitted from external pagers before voice announcement Reference e 1 14 Paging Features F G Paging e 2 6 1 Paging U M
23. U M Line 4 3 Extension Line Parameter Mailbox No Default Same as the extension number Value Range Up to 16 digits consisting of 0 9 or P Pause Description Function Specifies the Mailbox Number which is usually the same as the extension number Reference None Parameter CO Key Default CO 01 Loop CO Others Not Stored Value Range Please refer to Section 4 3 2 Flexible CO Key Assignment Description Function Used to determine the usage of the flexible CO buttons on a PT You can enter into Flexible CO Key screen in Section 4 3 2 Flexible CO Key Assignment by clicking CO Key button on this screen Reference e 4 1 2 Customising the Buttons U M Parameter PF Key Default Not Stored Value Range Please refer to Section 4 3 3 Flexible PF Key Assignment for PT Description Function Used to determine the usage of PF Programmable Feature buttons ona PT You can enter into Flexible PF Key screen in Section 4 3 3 Flexible PF Key Assignment for PT by clicking PF Key button on this screen Reference e 4 1 2 Customising the Buttons U M Parameter Initial Display Selection Default Caller ID Value Range 1 Caller ID 2 Trunk Name 3 DDI DID Name Description Function Specifies the initial display of a display PT when an incoming CO call with Caller ID information comes in on it Reference e 4 1 1 Initial Settings U M Line 151 4 3 Extension Line
24. aim an aim N oa 5 Lelhelkelke l HUHN N AANA EEE 8 H 5 9 DISA TIE User Code L e i Features 195 5 9 DISA TIE User Code Parameter Code Default All Blank Value Range 4 10 digits consisting of 0 9 Description Function Specifies the User Codes for DISA TIE feature Notes e DISA user code is required when the DISA caller attempts to make an outside call Trunk Security mode or to make either extension or outside call All Security mode e If TIE to CO Security mode in Section 4 2 Trunk Line is set to Yes entering TIE user code is required when the TIE caller attempts to make a CO call e If the entire code for example 1234 is included in another code for example 12345 it is not valid e When you enable the CO to CO transfer feature of DISA function if a third party knows the password there is a risk that someone else illegally may make a phone call using your telephone line and the cost may be charged to your account In order to avoid this to happen we strongly recommend you to keep the secrecy of the password and change the password frequently Reference e 1 5 Attended Features F G Direct Inward System Access DISA 3 1 E amp M Features F G E amp M TIE Line Service Parameter COS Default All 96 Value Range 1 96 Description Function Specifies COS Class of Service Level for each User Code Refe
25. 1 1 Slot Assignment Card Properties XXX ELCOT screen For information on Card Properties screen please refer to Card Type in Section 1 2 Slot Assignment e You must use Flash Time parameter in 1 1 Slot Assignment Card Properties XXX ELCOT screen when your Central Office requires a Flash Time not listed here e Please refer to Help file for detailed information on Card Properties ELCOT None Parameter Max Dial No after EFA Signal Default Value Range Description Function Reference 0 0 32 Specifies the maximum dialling digits allowed after sending EFA External Feature Access signal Note e If setto 0 the dialling digits can be sent without limit e 1 12 Conversation Features F G External Feature Access e 2 8 2 If a Host PBX is Connected U M 108 Group 3 2 Trunk Group Parameter PBX Access Code Default Blank Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the PBX access codes required to access the Host PBX or Centrex service If the system is installed behind a host PBX or a Centrex system an access code is required to make an outside Centrex call or to access Centrex features Up to four codes can be assigned per Trunk Group Reference e 1 3 System Features F G Host PBX Access 2 8 2 If a Host PBX is Connected U M Parameter PBX Dial Tone Default Disable Value Range 1 Enable 2 Disable D
26. 1 3 Trunk Port Assignment Used to assign each trunk port in the system to one of up to 48 trunk groups 1 2 Trunk Port Assignment CardNo pee xl BEE hehehehehe D 9 a 5 g 3 5 i ala 2 i Is a shhh q z a 10 44 12 13 14 cr ELLELLLL LEL PLULLLLL 1 2 Trunk Port Assignment oK Apply Cance Help Parameter Card No Default Value Range XXX YYY XXX Card No 101 314 YYY Card Type Description Function Specifies the physical number of the trunk card and its type which you are going to programme Reference 1 2 Slot Assignment P G 10 Configuration 1 3 Trunk Port Assignment Parameter Group No Default 48 E amp M card 1 Others Value Range 1 48 Description Function Specifies the trunk group 1 48 to which the trunk port is assigned Notes e Each trunk port must be assigned to a Trunk Group This programme defines the Trunk Group assignment for each trunk port e In some countries the El and the E amp M cards must not be connected to the Public Switched Network Reference e 1 3 System Features F G Trunk Group e 3 2 Trunk Group P G Parameter Status Default Value Range 1 INS 2 OUS 3 FAULT Description Function Specifies the operating status of the trunk port 1 INS The trunk port is In Service 2 OUS The trunk port is Out of Service 3 FAULT The trunk
27. Enable El DR2 card NL JT G Value Range 1 Enable 2 Disable Description Function Specifies whether CPC Detection on incoming CO calls is enabled or disabled If enabled the system disconnects the line with the time set in programme CPC Signal IN Detection Detection Time when the CPC signal is detected Note e In some countries the El and the ELCOT cards must not be connected to the Public Switched Network Reference e 1 3 System Features F G Calling Party Control CPC Signal Detection Parameter CPC Signal IN Detection Detection Time ELCOT card Default 32ms SP None NL JT Value Range 1 None 2 6 5 ms 3 2 75 x 8 ms Description Function Specifies the expected minimum duration for detecting CPC Calling Party Control signal on incoming CO calls Note Insome countries the ELCOT card must not be connected to the Public Switched Network Reference e 1 3 System Features F G Calling Party Control CPC Signal Detection Line 141 4 2 Trunk Line Parameter CPC Signal IN Detection Detection Time E1 DR2 card Default Value Range Description Function Reference 160 ms 1 None 2 1 15 x 80 ms Specifies the expected minimum duration for detecting CPC Calling Party Control signal on incoming CO calls Note e In some countries the El card must not be connected to the Public Switched Network e 1 3 System Features F G Calling Party C
28. MFC R2 Specifies the dial type when receiving an incoming call 1 Undefined Not assigned 2 Pulse DP Signalling sending receiving 3 DTMF DTMF Signalling sending receiving 4 MFC R2 MFC R2 Signalling sending receiving Digital signalling system R2 only None Parameter Status Default Value Range Description Function Reference 1 INS 2 OUS 3 FAULT Specifies the operating status of the El port 1 INS The E1 port is In Service 2 OUS The El port is Out of Service 3 FAULT The El port is defective hardware In this case the LED indicator on the El card will light None 24 Configuration 1 7 DISA Port Assignment 1 7 DISA Port Assignment Used to assign OGM group number for each DISA card 1 7 DISA Port Assignment Card No 7 Location OGM Group No Parameter Card No 1 8 Location Default Display only Value Range 101 314 Description Function Displays the slot number of the DISA card which you are going to programme Reference 1 2 Slot Assignment P G Parameter Card No 1 8 OGM Group No Default 1 Value Range 1 8 Description Function Specifies the OGM Group 1 8 to which the DISA card is assigned Reference e 1 3 System Features F G Outgoing Message OGM 3 6 OGM Group P G Configuration 25 1 8 BRI Port Assignment 1 8 BRI Port Assignment Used to assign the parameters for BRI Basic Rate Interface po
29. Parameter VPS Card Default None Value Range None XXX YYY XXX Card No 101 314 YYY Card Type Description Function Specifies the physical number of DLC DHLC card to which VPS is connected as extensions Reference e 1 3 System Features F G Integration VPS 1 2 Slot Assignment P G 18 Configuration 1 5 VPS DPT Port Assignment Parameter Type Default None Value Range 1 None 2 TVP100 3 TVP200 4 TVP200 1 Description Function Specifies the model number of the Panasonic Voice Processing System which will be connected to the VPS card Note e Please select TVP200 1 if HDD Hard Disc Software Version of your TVP200 is 2 00 or later Reference e 1 3 System Features F G Integration VPS Parameter Jack No Default Display only Value Range Description Function Displays the Jack No of VPS Reference e 1 3 System Features F G Integration VPS Parameter Port No Default Blank Value Range 1 16 DLC card 1 8 DHLC card Description Function Specifies the extension port to which the VPS DPT jack is to be connected Notes This programme tells the system which extension port is connected to the Panasonic Voice Processing System This allows the system to send the proper Digital Integration information to these ports e The port number is displayed only when the attribute of the port is assigned to VPS DPT Reference 1 4 Extension Port Assignment P G Co
30. TVP No menu the card DLC DHLC which connects with the TVP in VPS Card menu and the model of TVP in Type menu in 1 4 VPS DPT Port Assignment screen 4 Assignment of the extension port connected to the TVP Select in Port No menu the extension port number of the card DLC DHLC to which the TVP DPT jack is to be connected This menu is displayed only when the attribute of the port is assigned to VPS DPT at step 2 After Port No selection assign DN and Extension Group No for the port Configuration 17 1 5 VPS DPT Port Assignment Save the data changes by clicking Apply button Then set Port Status to INS In Service Jack No 1 must be assigned because the port is used as the channel to control the VPS 5 Synchronisation of the communication between the KX TD500 System and the TVP The KX TD500 System begins synchronisation with the VPS when the step 4 is done The Power LED of the VPS begins flashing at the same time The LED will turn on after the synchronisation is completed It takes for about 30 seconds to 1 minute to be able to use the VPS system It depends on the VPS model and the port number you set up Parameter TVP No Default 1 Value Range 1 8 Description Function Specifies the device number of a Panasonic Voice Processing System VPS which you are going to programme Reference e 1 3 System Features F G Integration VPS 1 2 Slot Assignment P G
31. Time Table No None UCD Setting FWD No Answer Disable UCD Setting Auto LOGOUT Mode Disable UCD Setting Supervisor Extension Blank UCD Setting LOGIN Monitor Disable UCD Setting UCD Call Waiting Enable 3 4 Paging Group Program Default Paging Group No 1 Extension Group No Paging Group No 1 only No 1 1 No 2 128 Others None 3 5 DIL 1 N Group Program Default Group No FDN Blank Default Values 297 Program Default Mailbox No Blank Destinations DN Blank Destinations Ringing Type Immediate 3 6 OGM Group Program Default Group No 1 FDN Blank Tenant No 1 OGM Type DISA Security Mode Trunk DISA built in Automated Attendant Tables Dial Blank 0 Dial 9 4 Line 4 1 Line 4 2 Trunk Line 4 2 1 Trunk Line Copy Program Default Card No Port No 1 Group No Display only Name C0001 C0192 Incoming Type 1 DIL ELCOT card 2 DID E1 DR2 E1 E amp M C MFC R2 E1 E amp M P MFC R2 3 DDI BRI PRI30 card 4 TIE E1 E amp M C Pulse DTMF E1 E amp M P Pulse DTMF E amp M card Dial Type DTMF 80 E1 E amp M ELCOT card SP NL JT Pulse 10 E1 E amp M ELCOT card G ISDN BRI PRI30 card Destination Day Night 1001 SP NL JT 2001 G Subscriber Blank 298 Default Values Program Default
32. U M Serial Interface Port PROG Port 1 Please refer to System Programming and Diagnosis with Personal Computer in Section 1 2 System Administration of the Features Guide Note e Generally speaking you should connect your Programming PC to Port 1 and your SMDR printer to Port 2 Parameter Serial Interface Port PROG Parity Default Display only Value Range None Description Function A parity code indicates what type of parity is used to detect an error in the string of bits composing a character Make an appropriate selection depending on the requirements of your printer or personal computer Note e Port 1 is fixed to None Reference None Parameter Serial Interface Port PROG NL Code Default CR LF Value Range 1 CR LF 2 CR Description Function Specifies the NL New Line Code for your printer or personal computer If your printer or personal computer automatically feeds lines with a carriage return select CR Carriage Return If not select CR LF Line Feed Reference None Maintenance 261 10 6 System Parameters Parameter Serial Interface Port PROG Word Length Default Display only Value Range 8 bits Description Function Defines the number of bits in each byte or character Note e Port 1 is fixed to 8 bits Reference None Parameter Serial Interface Port PROG Stop Bit Default Display only Value Range 1 bit Description F
33. 8 Rate Currency o e Currency Display Position Treatment of Charge Limit ____ Ched GTa Meter Count up by Answer Detection Enable Disable SET zA m ww ou uw Parameter Charge Display on LCD Default Meter Value Range 1 Meter 2 Charge Description Function Specifies the initial display format of the charge fee on a display PT Reference e 1 3 System Features F G Charge Fee Reference Parameter Charge by SMDR Default Meter Value Range 1 Meter 2 Charge Description Function Specifies the SMDR Output Mode of the telephone charge Reference e 1 3 System Features F G Station Message Detail Recording SMDR Features 213 5 14 Charge Parameter Charge Verification ID Code Tenant 1 8 Default 1234 Value Range 4 7 digits consisting of 0 9 Description Function Specifies the ID code required for the charge management When Tenant Service is employed the password for each tenant Tenant 1 to 8 can be assigned respectively Reference e 1 3 System Features F G Tenant Service e 4 2 Charge Fee Management Station Programming U M 2 2 Tenant P G Parameter Rate Default 1 0 Value Range 0 00001 999999 Description Function Specifies the charge rate per meter Notes e The telephone charge is calculated by multiplying the value of Rate and the meter the number of Pay Tones sent from the Central Office e Telephone charge is shown on a display PT in a max 8 digits including t
34. 8 System Option Message waiting lamp patterns 1 2 The available message waiting lamp patterns are as follows s k i 5 12 o 128 ON S 2 Pattern 01 OFF ON Pattern 02 OFF ON Pattern 03 OFF ON Pattern 04 OFF ON Pattern 05 OFF oo ik 2 72 ON a ee Pattern 06 OFF gt 256 ms System 87 2 8 System Option Message waiting lamp patterns 2 2 i I mi ON Pattern 07 OFF gt ON Pattern 08 OFF 9 20 ee ON Pattern 09 OFF ON Pattern 10 OFF ON Pattern 11 OFF ON Pattern 12 OFF 88 System 2 8 System Option Parameter 21 Illegal Number DISA Default Send reorder tone Value Range 1 Send reorder tone 2 Transferred to IRNA destination Description Function Specifies the treatment of the invalid DISA calls Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter 22 Illegal Number DDI DID Default Send reorder tone Value Range 1 Send reorder tone 2 Transferred to IRNA destination Description Function Specifies the treatment of the invalid DDI DID calls Reference e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDI Parameter 23 Illegal Number TIE Default Send reorder tone Value Range 1 Send reorder tone 2 Transferred to IRNA destination Description Function
35. Assignment Program Default Card No 1 8 Location Display only Card No 1 8 OGM Group No 1 1 8 BRI Port Assignment Program Default Card No Type CO DN Blank Group No 1 Status Default Values 287 1 9 PRI Port Assignment Program Default Card No Type Display only Group No 1 Status 2 System 2 1 System 2 2 Tenant Program Default Tenant No 1 Alert Extension Blank DAY NIGHT Switching Mode Manual Inter tenant Calling 1 8 No check Auto Start Time Day 1 SUN SAT 9 00 AM Night 1 SUN SAT 5 00 PM Day 2 SUN SAT Disable Night 2 SUN SAT Disable Music on Hold Source MUSI SP NL G Tone JT BGM Source MUSI Automatic Route Selection No check System Speed Dial TRS Level Override No check SP NL JT Check G System Speed Dialing Entries Max Tenant 1 1000 Tenant 2 1000 Tenant 3 8 0 Manager Extension DN Blank External Paging Tone Check Confirmation Tone for Station or External Paging Check 288 Default Values 2 3 Numbering Plan Hundred Block Extension Program Default 1 1st Hundred Block Extension 10 SP NL JT 20 G 2 2nd Hundred Block Extension 11 SP NL JT 21 G 3 3rd Hundred Block Extension 12 SP NL JT 22 G 4 4th Hundred Block Extension 13 SP NL JT
36. Code entry button CONF Conference button VTR Voice Mail Transfer button 2WAY REC Two way Recording button 2WAY TRN Two way Transfer button LCS Live Call Screening button LCS CANCEL Live Call Screening Cancel button ANSWER Answer button RELEASE Release button TONE THROUGH Tone Through button SS ISDN Service button 4 1 2 Customising the Buttons U M 4 4 3 Flexible PF Key Assignment for DSS Console Used to determine the usage of flexible PF buttons on DSS Consoles The following screen is displayed by clicking PF Key button on 4 3 DSS Console screen Line 171 4 4 DSS Console Flexible PF Key Others lt Key Type Assignment gt The following Key Type Assignment screen is displayed by clicking Not Stored button for each PF Key on the above screen Flexible PF Key Hot Stored Dial name 172 Line 4 4 DSS Console Additional Parameters Required by Key Type Depending on a Key Type additional parameters are required as follows Key Type Additional Parameters Description ONE TOUCH Dial Specifies the telephone number or feature access number up to 24 digits consisting of 0 9 x P S or F Note P Pause S Secret Dialling F Hook Flash Name Specifies the name for One Touch dial Up to 10 characters consisting of 0 9 A Z a z or the following marks lt gt amp SS Dial Speifie
37. Function Specifies other tenant numbers to which extensions in this tenant can make a call If no tenant numbers are checked in this field extension users within this tenant cannot make a call to extensions in other tenants Making calls from one tenant to another is not allowed by default Reference e 1 3 System Features F G Tenant Service Auto Start Time Specifies Start time of DAY NIGHT service on a day of the week basis This setting is valid when Auto mode is selected in DAY NIGHT Switching Mode setting Up to four time frames Day 1 Night 1 Day 2 Night 2 can be set up on each day of the week 34 System 2 2 Tenant Parameter Day 1 SUN SAT Default 9 00 AM Value Range 1 Disable 2 12 00 11 59 PM AM Description Function Specifies the start time for Day Service 1 Reference e 1 3 System Features F G Night Service Parameter Night 1 SUN SAT Default 5 00 PM Value Range Same as Day 1 Description Function Specifies the start time for Night Service 1 Reference e 1 3 System Features F G Night Service Parameter Day 2 SUN SAT Default Disable Value Range Same as Day 1 Description Function Specifies the start time for Day Service 2 Reference e 1 3 System Features F G Night Service Parameter Night 2 SUN SAT Default Disable Value Range Same as Day 1 Description Function Specifies the start time for Night Service 2 Reference e 1 3 System Feature
38. Group Reference e 1 3 System Features F G Tenant Service e 2 2 Tenant P G Parameter OGM Type Default DISA Value Range 1 DISA 2 UCD OGM 3 Wakeup Description Function Specifies the usage of OGM resources on DISA cards 1 DISA OGM for DISA feature 2 UCD OGM OGM for UCD group 3 Wakeup OGM for Wakeup message Reference e 1 5 Attended Features F G Direct Inward System Access DISA Group 129 3 6 OGM Group Parameter Security Mode Default Trunk Value Range 1 None 2 Trunk 3 All Description Function Specifies the Security Mode for DISA callers 1 None Non security mode DISA callers can make both outside and intercom calls via DISA without restriction 2 Trunk Trunk Security mode DISA callers are required to enter a pre assigned DISA user code to make outside calls via DISA 3 All All Security mode DISA callers are required to enter a pre assigned DISA user code to make both outside and intercom calls via DISA Assignable only when DISA is specified in OGM Type programming Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter DISA built in Automated Attendant Tables Dial 0 Dial 9 Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the extension numbers to each DISA built in Auto Attendant number Both DN of extensions and FDN Floating Directory Number of extension groups or phantom extensions or
39. Group No Default Blank Value Range 1 128 Description Function Specifies the Extension Group 1 128 to which the B2 channel of the VPS DPT port is assigned Note e Specifies the extension group number to which the type of extension group VM or AA is assigned Reference e 1 3 System Features F G Extension Group 3 3 Extension Group P G Parameter Status Default Value Range 1 INS 2 OUS 3 FAULT Description Function Specifies the operating status of the VPS DPT port 1 INS The VPS port is In Service 2 OUS The VPS port is Out of Service 3 FAULT The VPS port is defective Reference None Configuration 21 1 6 EI Port Assignment 1 6 El Port Assignment Used to assign parameters for E1 ports Note e In some countries the El card must not be connected to the Public Switched Network 1 6 E1 Port Assignment Bei ee CardNo 105 E1 Port Ho Channel Type Group No Receiver Type Status 4 os ous 4 Undefined gt ous 5 undefined undefined ous 7 ous 8 undefined gt ous 1 6 E1 Port Assignment Ba oK Apply Cancei nep How to set up an E1 card 1 Insert E1 card into a free slot Notes e El card should be installed in the free slot no 1 5 or 9 of each shelf e The next slot must be empty 2 Assign the card type of the slot to E1 in 1 1 Slot Assignment screen 3 Assign the channel type and the trunk group number of each
40. Humber to be added Max 20 Digits Trunk Group Ho none zron zone Jone none zfnene l vone wone z ak m T III elle Hone gt None F Hone None gt None gt None Hone gt Hone Hone M Hone None x Hone None M Hone Hone Hone gt Hone gt Hone None gt Hone Hone gt Hone Hone M Hone None M Hone None x Hone Zl Hone Z Hone none none None Hone Hone gt Hone gt None gt None Hone Hone gt Hone gt I 8 1 TIE Routing Table Parameter Entry No Default 01 08 Value Range 01 36 in 8 entries increments Description Function Specifies the entry number of Routing Table which you are going to programme Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter PBX Code Default Blank Value Range Up to 3 digits consisting of 0 9 Description Function Specifies the ID code for your PBX Required when your PBX is a part of a TIE Line Network Reference 3 1 E amp M Features F G E amp M TIE Line Service Private Network 237 82 TIE Routing Table Parameter Leading Digit Default Blank Value Range Up to 3 digits consisting of 0 9 or X Description Function Specifies the leading one two or three digits of the number for TIE calls Used to determine the trunk group for routing a TIE call Note e X can be used as a wild card character which substitutes
41. Name f Day Max 10 Characters MSH Line Ho On LLL 9 1 Humber Transformation ODER Parameter Entry No Default 0001 0010 Value Range 0001 1000 in 10 entries increments Description Function Specifies the entry number of DDI DID MSN No which you are going to programme Reference 1 5 Attended Features F G Direct Inward Dialling DID 2 4 ISDN Attended Features F G Direct Dialling In DDI Multiple Subscriber Number MSN Ringing Service Parameter Automatic Registration Default Please refer to Section 9 2 2 Automatic Registration of DDI DID MSN Numbers Value Range Description Function Reference DDI DID 241 9 2 Number Transformation Parameter DDI DID MSN No Default Blank Value Range Up to 16 digits consisting of 0 9 Description Function Specifies the DDI DID MSN number which will be sent from the Central Office to the KX TD500 system Note e The DDI DID MSN number which has already been assigned cannot be registered Reference e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDD Multiple Subscriber Number MSN Ringing Service Parameter Destination Day Night Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the DN FDN Extension Group TAFAS Phantom Extension Remote Resource where a DDI DID call comes in
42. Optional x C Enable Disable Call from TRS Level 7 Extension Time Limit of Outside Calls _ _ Transfer to CO Enable C Disable C Yes Ho C Enable Disable Cal PWD to CO _ Off Hook Call Announcement Call FWD Follow Me C Enable Disable OHCA Enable C Disable Enable Disable Busy Override DHD Override _ Busy Override Deny C Enable Disable C Enable Disable Enable C Disable Released Link Operation _ r Digits Restriction in CO Talk Automatic Hold C Enable C Disable Mode C Enable Disable SDNCOS Charge Management r ISDH CFU CFB CFHR C Enable Disable C Enable Disable 2 3 Class of Service xl OK Apply Cancel Help Parameter COS No Default 1 Value Range 1 96 Description Function Specifies the COS number which you are going to programme Reference e 1 3 System Features F G Class of Service COS 4 3 Extension Line P G Parameter Trunk Group Setting Default Please refer to Section 2 4 1 Trunk Group Setting Value Range Description Function Reference 58 System 2 4 Class of Service COS Parameter TRS Level Day Night Default 1 Value Range 1 8 Description Function Specifies the Toll Restriction level 1 8 for each COS number in Day Night mode respectively Reference e 1 6 Originating Features F G Toll Restriction Parameter Time Limit of Outside Calls Default No Value Range 1 Yes 2 No Description Function Speci
43. Parameter Confirmation Tone for Station or External Paging Default Check Value Range 1 Check Enable 2 No check Disable Description Function If checked confirmation tone is sent to the extension user who initiated the Station Paging or the External Paging Reference e 1 14 Paging Features F G Paging e 2 6 1 Paging U M 38 System 2 3 Numbering Plan 2 3 Numbering Plan Used to assign the leading digits of extension numbers and feature numbers for system features 2 2 Numbering Plan Feature Piel Ea nn an A 4 1st Hundred Block Extension 2 2nd Hundred Block Extension 3 3rd Hundred Block Extension 4th Hundred Block Extension 5th Hundred Block Extension 6th Hundred Block Extension Tth Hundred Block Extension 8th Hundred Block Extension 9 9th Hundred Block Extension 10 10th Hundred Block Extension E A 4 ass ox am comer now Parameter 1 1st Hundred Block Extension Default 10 SP NL JT 20 G Value Range 1 2 digits consisting of 0 9 Description Function Specifies the leading 1 or 2 digits of the extension number Any number 0 through 9 can be set Notes e If one digit is assigned as the leading digit 3 digit extension numbers can be assigned e Iftwo digits are assigned as the leading digits 4 digit extension numbers can be assigned Reference e 1 3 System Features F G Flexible Numbering System 39 2 3 Numbering Pla
44. Parameter FDN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the FDN Floating Directory Number for the DIL 1 N Group Reference e 1 3 System Features F G Floating Station Group 125 3 5 DIL 1 N Group Parameter Mailbox No Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the mailbox number of the DIL 1 N group When a DIL 1 N call is redirected to a VM extension by IRNA feature the system sends the digits of this mailbox number to the VPS When Mailbox No is set to Blank the system sends the FDN to the VPS Note e DN of VPS port cannot be assigned as a mailbox number and a DIL 1 N destination Reference None Parameter Destinations DN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies extensions and or Extension Groups that you are going to assign to the specified DIL 1 N Group Note e DN of VPS port cannot be assigned as a mailbox number and a DIL 1 N destination Reference e 1 3 System Features F G Flexible Numbering 2 3 Numbering Plan P G 126 Group 3 5 DIL 1 N Group Parameter Destinations Ringing Type Default Value Range Description Function Reference Immediate amp WN Immediate 1 ring Delay 3 ring Delay 6 ring Delay 5 No Ring Specifies the ringing delay of the calls arriving at extensions
45. Print out LOGIN LOGOUT Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether or not the Login Logout status of Extension Group members and Phantom extensions will be printed out by SMDR Reference e 1 8 Ringing Features F G Log In Log Out Maintenance 10 4 SMDR Parameter Print out Absent Message 6 9 Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether or not Absent Message 6 9 will be printed out by SMDR If enabled any extension user can activate the printout by setting the Absent Message 6 9 Reference e 1 3 System Features F G Hotel Application e 2 5 3 Showing an Absent Message on the Caller s Telephone Display Absent Message Capability U M Parameter Print out Check in Check out Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether or not Check in Check out information will be printed out by SMDR Reference e 1 3 System Features F G Hotel Application Maintenance 257 10 5 Power Failure Transfer 10 5 Power Failure Transfer Power Failure Transfer connects specific telephones any SLT and a certain type of APT to pre determined CO lines in the event of system power failure 10 3 Power Failure Transfer Bee Trunk Card Extension Card gt one gt 1 Hone x 13 Hone z 3 Hone xl 15 Hone xl 3 Hone 15 Hone xl 5 Ho
46. Range None 1 48 Description Function Specifies the Routing Plan No 01 48 which is used for routing the telephone number registered in Dial field above Reference e 1 6 Originating Features F G Automatic Route Selection ARS ARS Automatic Route Selection 229 7 4 Routing Plan 74 Routing Plan Used to specify the Trunk Group number 01 48 and Modified Digit Table number 01 48 to be used for each route plan and time schedule Up to 48 Routing Plan entries can be programmed in the system 7 3 ARS Routing Plan ME E Plan Ho ie Time A Trunk Group No None x Hone x Hone x Hone x Hone x Hone M Hone x Hone M Modification Table No Hone Hone None Hone xl Hone x Hone M Hone M Hone xl Modification Table No Hone x Hone x Hone x Hone M Hone x Hone M Hone M Hone x Modification Table Ho Hone xl Hone xl Hone x Hone Hone x Hone M Hone xl Hone xl Modification Table Ho Hone ox amoy comet tow Parameter Plan No Default 1 Value Range 1 48 Description Function Specifies the Routing Plan Table number which you are going to programme Reference e 1 6 Originating Features F G Automatic Route Selection ARS Parameter Time A B C D Trunk Group No Default None Value Range None 1 48 Description Function Specifies the TRG Trunk Group number which is used for routing the call Up to 16 trunk groups can be entered Reference e
47. Reference e 2 8 1 If a Doorphone Door Opener is Connected U M Parameter 24 External Paging Default 32 SP NL JT 64 G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for making a paging announcement through External Pagers Reference e 2 6 1 Paging U M System 43 2 3 Numbering Plan Parameter 25 External Paging Answer TAFAS Answer Default Value Range Description Function Reference 42 SP NL JT 44 G 1 4 digits consisting of 0 9 X or Specifies the feature number for answering paging announcements through External Pagers or TAFAS Trunk Answer From Any Station calls e 2 6 3 Answering a Paged Announcement U M Parameter 26 Station Paging Default Value Range Description Function Reference 33 SP NL JT 63 G 1 4 digits consisting of 0 9 X or Specifies the feature number for making a paging announcement through the built in speakers of PTs e 2 6 1 Paging U M Parameter 27 Station Paging Answer Default Value Range Description Function Reference 43 1 4 digits consisting of 0 9 X or Specifies the feature number for answering the paging announcement through the built in speakers of PTs e 2 6 3 Answering a Paged Announcement U M Parameter 28 CO Call Pickup Default Value Range Description Function Reference 4 1 4 digits
48. Service 208 Features 5 12 Caller ID Registration 5 12 Caller ID Registration Used to assign the Caller ID code identification code of the calling party to utilise Caller ID Service provided by a specific Central Office CO If an ID Code transmitted from CO is found in the Caller ID Code Table the caller s ID Code or a name given to the code is displayed on the display PT allowing the called party to recognise the caller before answering a call If the network provides telephone number only the system searches for the matching name from the Caller ID Code Table If the matching name is found the system will display both the telephone number and the name 5 12 Caller ID Registration Tenantno Mr Entry No Name Max 16 Characters Humber Max 24 Digits one Nn an RB vn 5 12 Caller ID Registration xl OK Apply Cancel Help Parameter Tenant No Default 1 Value Range 1 8 Description Function Specifies the tenant to which the Caller ID codes are assigned Required when Tenant Service is employed Reference 1 3 System Features F G Tenant Service 2 2 Tenant P G Features 209 5 12 Caller ID Registration Parameter Entry No Default 0001 0010 Value Range 0001 1000 in 10 codes increments Description Function Specifies the entry number of Caller ID codes which you are going to programme Referenc
49. Service to make up a telephone number for local call Digits are removed from the beginning of the received digits Reference e 1 5 Attended Features F G Caller ID Service Parameter Local Call Number to be added Default Blank Value Range Up to 4 digits consisting of 0 9 X or Description Function Specifies the number to be added to the telephone number sent from the Central Office by Caller ID Service to make up a telephone number for local call The number is added to the beginning of the received digits Reference e 1 5 Attended Features F G Caller ID Service Parameter Long Distance Call Digits to delete Default 0 Value Range 0 9 Description Function Specifies the number of digits to be deleted from the telephone number sent from the Central Office by Caller ID Service to make up a telephone number for long distance call Digits are removed from the beginning of the received digits Reference e 1 5 Attended Features F G Caller ID Service 207 5 11 Caller ID Modification Parameter Long Distance Call Number to be added Default 1 Value Range Up to 4 digits consisting of 0 9 X or Description Function Specifies the number to be added to the telephone number sent from the Central Office by Caller ID Service to make up a telephone number for long distance call The number is added to the beginning of the received digits Reference e 1 5 Attended Features F G Caller ID
50. Specifies the trunk port physical number 10101 to 31416 Tone Since any call does not come in on a DSS button with the current TD500 software this setting is not required GROUP CO Trunk Group No Specifies the Trunk Group number 01 48 Tone Since any call does not come in on a DSS button with the current TD500 software this setting is not required DSS EXT Specifies the extension number 3 or 4 digits ONE TOUCH Dial Specifies the telephone number or feature access number up to 24 digits consisting of 0 9 X P S or F Note P Pause S Secret Dialling F Hook Flash VTR DN Specifies the Directory Number of the Voice Mail extension 2WAY REC DN Specifies the Directory Number of the Voice Mail extension 2WAY TRN DN Specifies the Directory Number of the Voice Mail extension SS Dial Specifies the telephone number or feature access number up to 24 digits consisting of 0 9 x P S or F Note P Pause S Secret Dialling F Hook Flash 170 Line 4 4 DSS Console Parameter Key Type Default Value Range Description Function Reference Not Stored Please refer to Description Function Not Stored Key Type is not assigned SINGLE CO Single CO button GROUP CO Group CO button DSS Direct Station Selection button ONE TOUCH One Touch Dial button MESSAGE Message Waiting button FWD DND Call Forwarding Do Not Disturb button SAVE Saved Number Redial button ACCOUNT Account
51. UCD Setting UCD Call v Waiting W assignable Group 115 3 3 Extension Group Applicability of Group Types to Overflow Destinations Overflow Destination DN External OGM Extension Phantom RMT DIL 1 N Group Type Pager Group Group Extension Group None Terminate v Circular v Operator Vv Y v VM Y AA v UCD v v v v W assignable 3 3 1 Extension Group Copy Used to copy a part of or all settings of a certain Extension Group to all other Extension Groups at a time You can also specify one or several Extension Groups as the copy destination Copying the Extension Group Parameters to Other Extension Groups 1 Edit the parameters of the copy source Extension Group and save it 2 Point to the Copy button on 3 2 Extension Group screen of the copy source and click e Extension Group Copy screen is displayed e The current Extension Group copy source number is shown as Copy from Extension Group 1 128 116 Group 3 3 Extension Group Extension Group Copy Copy from Extension Group 1 r Copy Item r Destination Extension Group 4 N A w 4 gt Ele IV Tenant No F RYDIDHD Mode gt Overtiow Day F Overtiow Hight 7 Overfiow Timer 7 Operator Ringing Type 7 Operator Call Priority 1125 126 127 128 uch T29 ra ma M32 I Extension Call Hunting Select All Execu
52. While copying properties more than 16 cards cannot be selected Please break the task into two sets E1030 Cannot change the Port Attribute when currently assigned as VPS port under 1 4 VPS DPT Port Assignment When the port which is assigned to VPS DPT port is changed to extension port please change the port after deleting the assignment in 1 4 VPS DPT Port Assignment screen E1031 Assign the channel type before making the port INS In Service status The port of El card cannot be made INS In Service status when the channel type of the port is not assigned E1032 Cannot change the status of the VPS port which is in auto configuration mode Please change the status of the VPS port after auto configuration E1033 Proper card for this feature is not installed in the system In order to use this feature proper card must be installed in the system And card must be assigned under Slot Assignment E1034 Both extensions B1 and B2 of 1st jack connected to VPS must be always assigned Both extensions B1 and B2 of 1st jack are used for communication between PBX and VPS E1035 Cannot remove VPS port while the status is INS In Service Please make VPS port OUS Out of Service status before deleting the port E1036 Assign a port number before changing the port status The VPS port that does not have a port number cannot have its status changed E1037 Cannot change the status of the port Cannot c
53. any digit in its position Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter Digits to delete Default 0 Value Range 0 16 Description Function Specifies the number of digits to be deleted from the dialled digits Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter Number to be added Default Blank Value Range Up to 20 digits consisting of 0 9 Description Function Specifies the dialling number to be added to the dialled digits Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter Trunk Group No Default None Value Range None 1 48 Description Function Specifies the trunk group hunt sequence to be used when placing a TIE call The sequence is commonly used by all tenants but trunk group will be skipped if it does not belong to the same tenant as the caller Reference 3 1 E amp M Features F G E amp M TIE Line Service 238 Private Network Section 9 DDI DID DDI DID 239 91 DDI DID 91 DDI DID Used to assign parameters required to utilise DDI DID service TD500 Maintenance Programming 9 DDI DID 240 DDI DID 9 2 Number Transformation 92 Number Transformation 9 2 1 Number Transformation Used to specify several parameters for DDI DID MSN service 9 1 Number Transformation entryno EE DDI DID MSH No Max 16 Digits Se Automatic Registration Destination
54. at each port by default Specifies whether to enable or disable this monitoring function Assignable only when an ELCOT card is installed in the system Note e In some countries the ELCOT card must not be connected to the Public Switched Network None Line 143 4 2 Trunk Line Parameter Digits to receive DDI DID Default 4 E1 DR2 card 7 BRI PRI30 card SP NL JT 4 El DR2 card 8 BRI PRI30 card G Value Range 0 16 digits Description Function Specifies the number of receiving digits from a DDI DID trunk Assignable only when Incoming Type is set to DDI or DID Reference e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDI Parameter TIE Line Type Default 4 wires Value Range 1 2 wires 2 4 wires Description Function Specifies the voice path type of TIE Lines Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter TIE Line Sensitivity IN Default 0 dB Value Range 3 to 6 dB in 3 dB increments Description Function Specifies the voice level for reception Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter TIE Line Sensitivity OUT Default 0 dB Value Range 3 to 6 dB in 3 dB increments Description Function Specifies the voice level for transmission Reference 3 1 E amp M Features F G E amp M TIE Line Service
55. by some other application Or the device cannot be used for some reason E0009 COM port access failed ID XX XX stands for the error code of the Windows system E0010 Communication timeout Cannot detect a response from PBX when connecting PC to PBX directly using an RS 232C Cable E0011 No response from the modem Cannot detect a response from the modem because a modem is not connected to PC or the communication port COM parameter of PC is not correct 270 Programming Error Messages 11 1 Error Messages EXXXX Error Message Error Code Description E0012 Another maintenance device is connected There are three ways to access the PBX 1 By PC System Programming 2 by Remote System Programming or 3 by User Programming But only one at a time E0013 Please reconnect after the PBX becomes on line or off line completely Tried to connect the PC before the PBX became on line or off line completely Please try after the off line indicator on the top shelf goes off on line or turns on and off off line E0014 Please enter profile name Attempted to save remote connection parameters without profile name E0015 Failed Saving of remote connection parameters Remote connection parameters are saved as a file TD500 INT in the Windows system directory The TD500 maintenance programme creates this file automatically if the file does not exist However if the file ex
56. expires before the second digit is dialled the system assumes that the first digit is a DISA built in auto attendant number Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter DISA IRNA Time Default 60 s Value Range 5 240 s Description Function Specifies the length of time in seconds the system is to wait before activating IRNA Intercept Routing No Answer feature for DISA calls If a DISA call directed to a single extension is not answered within this timer the system redirects the DISA call to another pre programmed IRNA destination Note e Call Forwarding No Answer Time will override this timer if an extension has enabled Call Forwarding No Answer Reference e 1 5 Attended Features F G Direct Inward System Access DISA System 2 5 System Timer Parameter Intercept Timer after OGM Default 5s Value Range 1 0 Immediately 2 5 5 s later Description Function Specifies the length of time in seconds the system is to wait after sending OGM before directing the call to the IRNA destination Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter Timed Reminder Arrive Wait Time Default 60 s Value Range 20 240 s Description Function Specifies the interval time between each Timed Reminder Remote Timed Reminder Wake Up Call attempt Reference e 1 8 Ringing Features F G Timed Reminder Wake Up Call Timed Reminder Remote
57. following marks lt gt amp Description Function Specifies the name for each speed dial code Note The stored name is shown on a large display PT such as KX T7235 KX T7536 when dialling System Speed Dialling number Reference e 2 10 4 Using the KX T7531 KX T7533 KX T7536 or KX T7235 U M Parameter Number Default Blank Value Range Up to 24 digits consisting of 0 9 x P S or F Description Function Specifies the telephone number for each speed dial code Note e P Pause S Secret Dialling F Hook Flash Reference None 186 Features 5 3 Phantom Extension 5 3 Phantom Extension Used to register up to 448 Phantom Extension numbers 5 2 Phantom Extension 5 2 Phantom Extension Parameter Entry No Default 001 048 Value Range 001 448 in 48 codes increments Description Function Specifies the entry number of phantom extension number which you are going to programme Reference 1 3 System Features F G Phantom Extension Parameter FDN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the FDN Floating Directory Number for each Phantom button Note e A single Phantom extension number can be assigned to multiple extensions so that the caller can ring a group of extensions simultaneously Reference e 1 3 System Features F G Floating Station e 4 1 2 Customising the Butto
58. for DISA built in Automated Attendant Tables Both DN of extensions and FDN of extension groups or phantom extensions or TAFAS can be assigned as DISA built in Automated Attendant Tables E3009 DIL 1 N destination duplicated The directory number of the extension or extension group must be unique as a destination of DIL 1 N E3010 Invalid Mailbox Number Only DN of an extension or FDN of an extension group can be assigned as a DIL 1 N Mailbox Number E4003 Invalid LCS playback password The LCS playback password must be 3 digits 0 9 E4004 Invalid Call Log lock password The Call Log lock password must be 3 digits 0 9 Programming Error Messages 275 11 1 Error Messages EXXXX Error Message Error Code Description E4005 Invalid Station Lock password The Station Lock password must be 3 digits 0 9 E4006 Specify trunk line no Trunk line no must be specified when Single CO key is assigned E4007 Single CO key duplicated Please assign the Single CO key that has the different CO physical number on one PT E4008 Invalid directory number for DSS DN key Only DN of an extension can be assigned as DSS DN key E4009 DSS DN key duplicated Two DSS keys cannot have the same extension number E4010 Invalid directory number for PHANTOM key Only FDN of phantom extension can be assigned to phantom key number E4011 Cannot assign PDN key without assigning PDN key on
59. fs ra IV PBX Access Code IV Cyclic Signal Detection I 108 24 13 m IV Continuous Signal Detection 10 22 34 46 IV Silence Detection rn 23 135 147 IV PBX Ringback Tone 42 E 24 36 48 IV Type IV Numbering Plan ID IV Type of Humber Select All IV Max Dial No after EFA Signal j Execute Cancel Help 3 Select the Trunk Group parameters to copy in Copy Item field Items marked with W are copied 4 Point to the Select All button in the Destination Trunk Group field and click e All displayed Trunk Group Nos will be marked with VW e You can also specify one or several Trunk Groups as the copy destination by clicking it them directly 5 Point to the Execute button and click e Are you sure is displayed 6 Point to the Yes Y button and click e Copying is displayed while the source data is being copied to the destination e Parameters of the destination Trunk Groups are immediately effective when copying is finished Parameter Group No Default 1 Value Range 1 48 Description Function Specifies the trunk group 1 48 which you are going to programme Reference e 1 3 System Features F G Trunk Group 104 Group 3 2 Trunk Group Parameter Type Default Public Value Range 1 Public 2 Private 3 VPN Virtual Private Network Description Function Specifies the network type for the trunk gruop Reference None Parameter Tenant No Default 1
60. in the DIL 1 N group 1 2 Immediate An extension rings immediately 1 ring Delay An extension rings in 1 ring delay timing 3 ring Delay An extension rings in 3 ring delay timing 6 ring Delay An extension rings in 6 ring delay timing No Ring An extension does not ring e 1 13 Audible Tone Features F G Ringing Delayed Group 127 3 6 OGM Group 3 6 OGM Group Used to assign parameters for OGM Groups 1 8 OGM resources on the DISA card can be grouped together as an OGM Group 3 5 OGM Group Se Group No A FDH m Tenant No U orere OGM Type Security Mode DISA built in Automated Attendant Tables pit ma El vias mas pias mas waz mas pias miao 1 3 5 OGM Group oK apply Cancel Help Parameter Group No Default 1 Value Range 1 8 Description Function Specifies the OGM Group 1 8 which you are going to programme Reference None Parameter FDN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the FDN Floating Directory Number for each OGM group Reference e 1 3 System Features F G Floating Station 128 Group 3 6 OGM Group Parameter Tenant No Default 1 Value Range 1 8 Description Function Specifies the tenant to which you are going to assign this OGM
61. is deleted E5011 Specify the leading digits The ARS leading dial also must be entered when the Route Plan Table No is assigned and the Route Plan Table No also must be deleted when the leading dial is deleted E5020 Charge Verification ID Code format error Please assign the Charge Verification ID code of 4 digits consisting of 0 9 E5021 Don t keep Rate to be Blank The value of Rate must be always assigned E6001 Too long TRS Deny or Exception dial TRS Deny or Exception dial can be registered up to 10 digits consisting of 0 9 x or X a wild card E6002 Cannot assign more than 400 TRS deny codes There is a limit of 400 toll restriction deny codes per system E6003 Cannot assign more than 200 TRS exception codes There is a limit of 200 toll restriction exception codes per system E7001 Invalid arrangement of time zones Each successive ARS time zone must be later in time Namely this pattern must be followed Time A lt Time B lt Time C lt Time D E7002 Assign both trunk group number and modification table number Cannot assign just trunk group number or just modification table number Both must be assigned as a pair under ARS routing plan E9001 Invalid directory number for DDI DID destination There are five possible destinations for DDI DID calls 1 An extension 2 an external pager TAFAS 3 a remote extension 4 an extension group or 5 a phantom extension
62. leading 8 digits are saved and the rest are deleted W4007 Mailbox number must not exceed 16 digits Truncate it Truncate means that the leading 16 digits are saved and the rest are deleted A digit can be 0 through 9 or P pause W5001 System Speed Dialing name must not exceed 10 characters Truncate it Truncate means that the leading 10 characters are saved and the rest are deleted W5002 System Speed Dialing number must not exceed 24 digits Truncate it Truncate means that the leading 24 digits are saved and the rest are deleted W5003 Emergency dial number must not exceed 8 digits Truncate it Truncate means that the leading 8 digits are saved and the rest are deleted W5004 Quick Dial number must not exceed 16 digits Truncate it Truncate means that the leading 16 digits are saved and the rest are deleted W5005 Account Code must not exceed 10 digits Truncate it Truncate means that the leading 10 digits are saved and the rest are deleted W5006 Special Carrier Code must not exceed 10 digits Truncate it Truncate means that the leading 10 digits are saved and the rest are deleted W5008 Absent message must not exceed 16 characters Truncate it Truncate means that the leading 16 characters are saved and the rest are deleted W5009 VPS integration code must not exceed 3 digits Truncate it Truncate means that the leading 3 digits are saved and the rest are deleted W5010 Voice Mail c
63. less than 16 digits Please change Digits to delete and or Number to be added E5001 Assign both name and number for Caller ID Cannot assign just the name for Caller ID E5002 Cannot use more than seven characters There can be a maximum of seven characters in an absent message E5003 User code format error Please assign the DISA TIE user code of 4 10 digits consisting of 0 9 E5004 User code duplicated Each code in the DISA TIE User Code must have a unique number E5005 Cannot set RET command at the head Please set the command except for RET at the head of UCD Time Table Programming Error Messages 277 11 1 Error Messages EXXXX Error Message Error Code Description E5006 Cannot assign more than 1000 account codes There is a limit of 1000 account codes per system E5007 You have exceeded the tenant limit of Speed Dialing numbers The maximum number of Speeding Dialling numbers per tenant is specified in the 2 1 Tenant screen E5008 You have exceeded the limit of Caller ID codes There is a limit of 1000 Caller ID codes per tenant and 2000 Caller ID codes per system E5009 Invalid User code If the entire code for ex 1234 is included in another code for ex 12345 it is not valid E5010 Specify the code The account code also must be entered when the TRS Level is assigned and the TRS Level also must be deleted when the account code
64. operation Default No limit Value Range 1 Limited 10 times 2 No limit Description Function Specifies the number of times that the DISA caller can prolong the duration of DISA CO to CO line call Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter 14 Dialing in DISA CO to CO talking Default Disconnect and make a new call Value Range 1 Disconnect and make a new call 2 Send out Dial x Description Function The X key can be entered during a DISA CO to CO line call The action taken by the system depends upon this setting If Disconnect and make a new call is selected then the system will disconnect the current call and prepare for a new call Otherwise the will be transmitted down the line to the other party Reference e 1 5 Attended Features F G Direct Inward System Access DISA 83 2 8 System Option Parameter 15 Special dial tone after setting feature Default Value Range Description Function Reference Enable 1 Enable 2 Disable If enabled the system notifies the extension user by sending a special dial tone Dial Tone 2 when one or more of the following features are assigned on his her extension e Absent Message Capability e Background Music BGM e Call Forwarding e Call Pickup Deny e Call Waiting e Data Line Security e Do Not Disturb DND e Electronic Station Lockout e Executive Busy Override Deny e Paging Deny e Pick
65. port in 1 6 El Port Assignment screen Note e The channel type should be assigned on the basis of the contract with a telephone exchange 4 Assign the parameters of the port like usual trunk line in 4 1 Trunk Line screen 5 Change the card status to INS In Service in 1 1 Slot Assignment screen All the ports are changed to INS In Service status automatically 22 Configuration 1 6 EI Port Assignment Parameter Card No Default Value Range XXX El XXX Card No 101 314 Description Function Specifies the physical number of the El digital trunk card which you are going to programme Reference 1 2 Slot Assignment P G Parameter Channel Type Default Undefined Value Range 1 Undefined 2 DR2 3 E amp M P 4 E amp M C Description Function Specifies the type of El interface per channel 1 Undefined Not assigned 2 DR2 Digital signalling system R2 3 E amp M P Pulsed E amp M 4 E amp M C Continuous E amp M Reference e 1 3 System Features F G E1 Carrier Parameter Group No Default Blank Value Range 1 48 Description Function Specifies the Trunk Group 1 48 to which the El port is assigned Reference e 1 3 System Features F G Trunk Group 3 2 Trunk Group P G Configuration 23 1 6 EI Port Assignment Parameter Receiver Type Default Value Range Description Function Reference Undefined 1 Undefined 2 Pulse 3 DTMF 4
66. the Extension Line parameters to copy in Copy Item field e Only parameters which are available to copy are shown in Copy Item field This depends on the attribute of the copy source Extension Line e Items marked with W are copied 4 Point to the Select All button in the Destination Extension Line field and click e All displayed Extension Line Nos will be highlighted e You can also specify one or several Extension Lines as the copy destination by clicking it them directly 5 Point to the Execute button and click e Are you sure is displayed 6 Point to Yes Y button and click e Copying is displayed while the source data is being copied to the destination e Parameters of the destination Extension Lines are immediately effective when copying is finished Parameter Card No Default Value Range XXX YYY XXX Card No 101 314 YYY Card Type Description Function Specifies the physical number of the extension card and its type which you are going to programme Reference e 1 2 Slot Assignment P G 148 Line 4 3 Extension Line Parameter Port No Default 1 Value Range 1 32 Description Function Specifies the extension port which you are going to programme Note e Port Nos 17 32 will be displayed when DN and Group No for Ext No 2 are assigned in 1 4 VPS DPT Port Assignment screen Section 1 5 Reference e 1 4 Extension Port Assignment P G Paramete
67. the sum total of telephone charge allowable to extension users on an ISDN extension basis If the telephone charge on the ISDN extension exceeds the limit a toll call cannot be made anymore from that extension Note e If the charge limit is set to 0 no restriction is applied Reference e4 2 Charge Fee Management Station Programming U M Parameter Tone Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether the system sends the call progress tone to the ISDN extension or not Reference None Line 179 4 7 ISDN Extension Line Parameter ISDN Bearer Mode Default Automatic Value Range 1 Automatic 2 Speech 3 3 1 KHz Audio Description Function Specifies the ISDN Bearer Mode on an ISDN extension basis Note e When Automatic Default is selected Bearer Mode is set automatically depending on the type of extension telephone as follows PT Speech SLT 3 1 KHz Audio ISDN extension depending on the bearer mode of the ISDN extension Reference 2 1 ISDN Features F G Integrated Services Digital Network ISDN Parameter Numbering Plan ID Default Default Value Range 1 Default 2 Unknown 3 ISDN Telephony 4 National Standard 5 Private Description Function Specifies the Numbering Plan ID applied to the outgoing incoming CO calls via ISDN Public Network Reference None Parameter Type of Number Default Default Value Range 1 Default 2 Unknown
68. trunk line is assigned Note e Each trunk line is assigned to a Trunk Group in Section 1 3 Trunk Port Assignment Reference e1 3 Trunk Port Assignment P G Parameter Name Default C0001 C0192 Value Range Up to 10 characters consisting of 0 9 A Z a z or the following marks x 3 lt gt 7 amp Description Function Specifies the name for the trunk line Note e This is shown on a display PT when making or receiving a call using this trunk Reference e 1 17 Display Features F G Display Call Information 135 4 2 Trunk Line Parameter Incoming Type Default 1 DIL ELCOT card 2 DID E1 DR2 E1 E amp M C MFC R2 E1 E amp M P MFC R2 3 DDI BRI PRI30 card 4 TIE E1 E amp M C Pulse DTMF El E amp M P Pulse DTMF E amp M card Value Range 1 DIL DID TIE DDI MSN nun 136 Line 4 2 Trunk Line Parameter Incoming Type Description Function Specifies how the incoming CO call via this trunk line is routed to the destination in the system 1 DIL Incoming CO calls are routed by DIL Direct In Lines 1 1 or 1 N feature 2 DID Incoming CO calls are routed by DID Direct Inward Dialling feature 3 TIE Incoming CO calls are routed by TIE Line feature 4 DDI Incoming CO calls are routed by ISDN DDI Direct Dialling In feature 5 MSN Incoming CO calls are routed by ISDN MSN Multiple Subscriber Number feature lt Available selections and t
69. 0 48 rings Description Function Specifies the number of rings before transfer recall occurs If a transferred call is not answered before the programmed number of rings the call returns to the extension user who originally transferred it or an Operator depending on the setting of 6 Transfer recall destination in Section 2 8 System Option Note e If O is specified Transfer Recall does not occur Reference None Parameter Pickup Dial Waiting Time Default ls Value Range 1 5s Description Function Specifies the length of time in seconds that the system is to wait after an extension user goes off hook for making a call before the system automatically dials the pre assigned telephone number for Pickup Dialling Note e This waiting time gives the extension user an opportunity to dial another number before automatic dialling is performed Reference 1 7 Dialling Features F G Pickup Dialling Hot Line e 2 2 2 Easy Dialling U M Parameter Call Duration Count Start Time Default Os Value Range 0 60 s Description Function Specifies the length of time in seconds the system is to wait after sending all dialling digits to the Central Office before starting the call duration count Note e The elapsed time of the call duration is shown on a display PT Reference e 1 3 System Features F G Station Message Detail Recording SMDR 68 System 2 5 System Timer Parameter First Digit Time Defa
70. 1 None 2 Terminate 3 Circular 4 Ring 5 Operator 6 VM 7 AA 8 UCD Description Function Specifies the Group Type for each Extension Group This determines how the Extension Group handles the incoming calls directed to it 1 None No Group Type is specified 2 Terminate Functions as a Station Hunting Group Terminate 3 Circular Functions as a Station Hunting Group Circular 4 Ring Functions as a Ring Group 5 Operator Functions as an Operator Group 6 VM Functions as a VM Voice Mail Group 7 AA Functions as an AA Automated Attendant Group 8 UCD Functions as a UCD Uniform Call Distribution Group Reference e1 3 System Features F G Extension Group 118 Group 3 3 Extension Group Parameter Tenant No Default 1 Value Range 1 8 Description Function Specifies a tenant number 1 8 to which the Extension Group is assigned Required if Tenant Service is employed Reference e1 3 System Features F G Tenant Service 2 2 Tenant P G Parameter Overflow Setting Destination Day Night Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the destination extension where the call is transferred to when all extensions in the Extension Group are unavailable or logged out in Day Night mode respectively Reference None Parameter Overflow Setting Timer Default None Value Range None 5 180 s in 5 s increments
71. 1 6 Originating Features F G Automatic Route Selection ARS 230 ARS Automatic Route Selection 7 4 Routing Plan Parameter Time A B C D Modification Table No Default None Value Range None 1 48 Description Function Specifies the MOD Modified Digit table number which is used to modify the user dialled number so that it matches the requirements of the carrier Reference e 1 6 Originating Features F G Automatic Route Selection ARS ARS Automatic Route Selection 231 7 5 Digits Modification Table 7 5 Digits Modification Table Used to modify the user dialled number so that it matches the requirements of the carrier Up to 48 Digits Modification entries can be programmed in the system 7 4 ARS Digits Modification Table N o a 2 wo oo wN BEE Digits to Humber to be added Max 20 Digits i 7 4 Digits Modification Table Parameter Entry No Default 01 08 Value Range 01 48 in 8 entries increments Description Function Specifies the entry number of Digits Modification table which you are going to programme Reference e 1 6 Originating Features F G Automatic Route Selection ARS Parameter Digits to delete Default 0 Value Range 0 9 Description Function Specifies the number of digits to be deleted from the beginning of the user dialled number If you set to 0 no digit is deleted from the user dialled n
72. 2 only 6 3 TRS Exception Code Program Default TRS Level 6 Entry No 001 020 Dial Blank SP NL JT XXXXXXX G Level 2 only 7 ARS Automatic Route Selection 7 1 ARS Automatic Route Selection 7 2 Time Table Program Default Time A B C D SUN MON TUE WED THU FRI SAT Time A 8 00AM Time B 5 00PM Time C 9 00PM Time D Disable 7 3 Leading Digits Table Program Default Entry No 001 020 Dial Blank Default Values 307 Program Default Routing Plan No None 7 4 Routing Plan Program Default Plan No 1 Time A B C D Trunk Group No None Time A B C D Modification Table No None 7 5 Digits Modification Table Program Default Entry No 01 08 Digits to delete 0 Number to be added Blank 8 Private Network 8 1 Private Network 8 2 TIE Routing Table Program Default Entry No 01 08 PBX Code Blank Leading Digit Blank Digits to delete 0 Number to be added Blank Trunk Group No None 308 Default Values 9 DDI DID 9 1 DDI DID 9 2 Number Transformation 9 2 1 Number Transformation Program Default Entry No 0001 0010 Automatic Registration Please refer to Section 9 2 2 Automatic Registration of DDI DID MSN Numbers DDI DID MSN No Blank D
73. 3 International 4 National 5 Network Specific 6 Subscriber Description Function Specifies the type of number applied to the outgoing incoming CO calls via ISDN Public Network Reference None 180 Line 4 7 ISDN Extension Line Parameter CLIP COLP Number Public Default Value Range Description Function Reference Blank Up to 16 digits consisting of 0 9 X or P PAUSE Specifies a CLIP COLP number used for the incoming outgoing calls via Public Network to each ISDN extension Note e The KX TD500 System is designed and manufactured in accordance with the following ETS European Telecommunication Standard specifications ETS 300 122 Generic Keypad protocol for the support of supplementary services 2 2 ISDN Originating Features F G Calling Line Identification Presentation CLIP 2 3 ISDN Answering Features F G Connected Line Identification Presentation COLP Parameter CLIP COLP Number Private Default Value Range Description Function Reference Blank Up to 16 digits consisting of 0 9 X or P PAUSE Specifies a CLIP COLP number used for the incoming outgoing calls via Private Network to each ISDN extension Note e The KX TD500 System is designed and manufactured in accordance with the following ETS European Telecommunication Standard specifications ETS 300 122 Generic Keypad protocol for the support of supplementary services 2 2 I
74. 800 Leading Digits entries can be programmed in the system 7 2 ARS Leading Digits Table Be E Enno ET Dial Routing Plan No Max 10 Digits No ss None 12 ss Hone ss None 13 WE None Bun a CEE Leelee eee EA elie beh z z 2 3 of 7 2 Leading Digits Table x OK Apply Cancel Help Parameter Entry No Default 001 020 Value Range 001 800 in 20 entries increments Description Function Specifies the entry number which you are going to programme Reference e 1 6 Originating Features F G Automatic Route Selection ARS 228 ARS Automatic Route Selection 7 3 Leading Digits Table Parameter Dial Default Blank Value Range Up to 10 digits consisting of 0 9 x or X Description Function Specifies the leading 10 digits of the telephone number which will be routed by ARS procedure Note e X can be used as a wild card character which substitutes any digit in its position Example 1 Leading Digits 1800 ARS Plan 1 Leading Digits 1 x x X ARS Plan 2 If the user dialled number is 1800 the system selects ARS Plan 1 Example 2 Leading Digits 1800 ARS Plan 1 Leading Digits 1 x gt ARS Plan 2 If the user dialled number is 1800 the system selects ARS Plan 2 Reference e 1 6 Originating Features F G Automatic Route Selection ARS Parameter Routing Plan No Default None Value
75. 9 X or Description Function Specifies the feature number for turning on off the Night Service mode Reference e 2 11 4 Switching the Day Night Service U M Parameter 52 Parallel Telephone Mode Default 39 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for setting cancelling Parallel Telephone mode Reference 2 7 13 Setting the Parallel Connected Telephone Ringer Parallelled Telephone Connection U M Parameter 53 External BGM On Off Default 35 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for turning on off External BGM For Manager Operator only Reference e 3 2 1 Turning on the External Background Music Background Music BGM External U M 50 System 2 3 Numbering Plan Parameter 54 Live Call Screening Default 799 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for setting cancelling Live Call Screening feature Reference e 2 8 3 If a Voice Processing System is Connected U M Parameter 55 Call Log Incoming Overwrite Mode Default 56 SP NL JT 54 G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for turning on off the Call Log Incoming Overwrite Mode If turned on e g 561 overwriting the buffer will occur If turned off e g 560
76. BRI Port No n Group Ho 1 Name Max 10 Characters Charge Limit Tone OO u Cat sable ISDH Bearer Mode Numbering Plan ID r Type of Number Defaut J Defaut z CLIP COLP Number Max 16 Digits COS No ray Secondary 46 ISDH Extension Line Parameter Card No Default Value Range XXX BRI XXX Card No 101 314 Description Function Spesifies the physical number of the BRI card which you are going to programme Reference 1 2 Slot Assignment P G Parameter Port No Default 1 Value Range 1 3 5 7 Description Function Specifies the ISDN extension port which you are going to programme Reference None 178 Line 4 7 ISDN Extension Line Parameter Group No Default Display only Value Range 1 128 Description Function Displays the Extension Group to which the selected ISDN extension port is assigned Reference 1 8 BRI Port Assignment P G Parameter Name Default Blank Value Range Up to 10 characters consisting of 0 9 A Z a z or the following marks x 3 lt gt 7 amp Description Function Specifies the name for the ISDN extension line Reference e 1 17 Display Features F G Display Call Information Parameter Charge Limit Default 0 Value Range 0 No limit 1 99999 The number of charge meter allowable for the ISDN extension Description Function Used to determine
77. CO 01 The first PDN key should be assigned on CO 01 E4012 Cannot change PDN key on CO 01 while other PDN or SDN keys exist Please change PDN key on CO 01 to another key type after deleting all PDN and SDN assignments E4013 Cannot assign SDN key without assigning PDN key An SDN button should have its associated PDN button E4014 Cannot assign more than 8 SDN keys for one PDN key Up to eight SDN keys per PDN key can be assigned on eight different PTs respectively E4015 Invalid directory number for SDN key Only DN of an extension can be assigned to SDN key number E4016 SDN key duplicated Two SDN keys cannot have the same extension number E4017 Cannot assign SDN key to its own directory number Please assign SDN to a directory number other than its own E4018 Dial registration resource exhausted Cannot register any more because the system resource that stores extension mailbox numbers voice mail access codes and One Touch Dialling numbers has been exhausted E4020 Invalid directory number for doorphone call destination Only DN of an extension can be assigned as a doorphone call destination E4021 Secret dial S must be placed at the beginning and end of desired secret numbers Cannot assign Secret Dialling S that is registered in One Touch dialling without being even number 276 Programming Error Messages 11 1 Error Messages EXXXX Error Message
78. Code is transmitted to the VM port and the VM service does not work Reference e 1 3 System Features F G Integration VPS 203 5 10 VPS Integration Parameter Extension s mailbox number Default Value Range Description Function Reference Programmed number 1 Extension number 2 Programmed number Specifies if an extension s mailbox number is substituted by the extension number or it is programmable free If a call is forwarded or rerouted to the VPS the system automatically transmits the mailbox number to the VPS to specify the extension user s mailbox To make it programmable select Programmed number then assign the mailbox number by Mailbox No setting in Section 4 3 Extension Line e 1 3 System Features F G Integration VPS Parameter Call from AA port to AA port Default Value Range Description Function Reference Allow 1 Allow 2 Deny Allows or disallows calling from an AA port of VPS to another AA port e 1 3 System Features F G Integration VPS Parameter Sending out Follow on ID after FWD Default Value Range Description Function Reference Enable 1 Disable 2 Enable Specifies whether or not the system sends Follow on ID to a VPS port after forwarding a call to the VPS port e 1 3 System Features F G Integration VPS 204 Features 5 10 VPS Integration Parameter Sending ou
79. Description Function Specifies the length of time in seconds the system is to wait before transferring the call in the waiting queue to the Overflow Destination Assignable only when Operator is specified in Group Type programming Note e If None is specified the call is transferred to the Overflow Destination immediately Reference e1 3 System Features F G Operator Group 119 3 3 Extension Group Parameter FWD DND Mode Default Enable Value Range 1 Disable 2 Enable Description Function Specifies whether to enable or disable the FWD DND Call Forwarding or Do Not Disturb feature assigned on all extensions in the Extension Group Assignable only when Terminate Circular or UCD is specified in Group Type programming Reference None Parameter Extension Call Hunting Default Enable Value Range 1 Enable 2 Disable Description Function Specifies whether station hunting feature works or not when the other party calls a busy extension in the group by dialling DN of the extension extension call Note e When the other party calls the group by dialling the FDN of the group station hunting always works regardless of this setting Reference 1 8 Ringing Features F G Station Hunting Parameter Operator Setting Ringing Type Default Single Value Range 1 Multi 2 Single Description Function Specifies whether the calls coming in on an Operator Group ring one Operator Si
80. E1 PRI30 or BRI card the status must be OUS Out of Service E2001 Invalid time format Please specify the time as Hour 0 1 12 Minute 0 0 59 E2003 Invalid division of DAY and NIGHT mode Time to specify with Day 1 Night 1 Day 2 and Night 2 must be the relations of Day 1 lt Night 1 lt Day 2 lt Night 2 E2005 Maximum entry number of System Speed Dialing exceeded The system provides up to 1000 tenant 2000 system of System Speed Dialling entries available to all extension users E2006 Cannot change System Speed Dialing Entries Maximum Please delete System Speed Dialling entries until there is less than the setting you want Then set System Speed Dialling Entries Maximum once again E2007 Invalid directory number for manager extension Only DN of an extension can be assigned as a manager extension FDN cannot be assigned E2008 Feature number is too long Feature numbers Hundred Block Extension or Other PBX can be set as the leading 1 or 2 digits of the extension number E2009 Cannot delete the Hundred Block Extension which is currently in use as DN or FDN Cannot delete the hundred block number It s already used as DN or FDN Please delete the hundred block number after you remove the registrations of DN or FDN 274 Programming Error Messages 11 1 Error Messages EXXXX Error Message Error Code Description E2010 Feature number duplicated Featur
81. Electric Co Ltd KME You may print out this manual solely for internal use with TD500 Except above you may not reproduce this manual in any form in whole or part without the prior written consent of KME Kyushu Matsushita Electric Co Ltd 2000 Kyushu Matsushita Electric Co Ltd 1 62 4 chome Minoshima Hakata ku Fukuoka 812 8531 Japan Printed in Japan PSQX1862ZA KK0300MYO CE
82. FWD No Answer Default Value Range Description Function Reference Disable 1 Disable 2 Enable Specifies the treatment of the call which is not answered by the extension in the UCD group within a specified period of time Call Forwarding No Answer Time 1 Disable The call continues to ring the current destination extension 2 Enable The system transfers the call to an idle extension in the group 1 3 System Features F G Extension Group Parameter UCD Setting Auto LOGOUT Mode Default Value Range Description Function Reference Disable 1 Disable 2 1 10 times Specifies the treatment of extensions ina UCD group who do not cannot answer the call A member extension may be logged out automatically if it does not answer the call for pre determined times 1 10 consecutively If Disable is specified this setting does not function e1 3 System Features F G Extension Group 1 5 Attended Features F G Uniform Call Distribution UCD Parameter UCD Setting Supervisor Extension Default Value Range Description Function Reference Blank 3 4 digits consisting of 0 9 Specifies the Supervisor Extension per UCD Group The extension specified as the Supervisor Extension can monitor the number of waiting calls calls placed in the waiting queue 1 3 System Features F G Extension Group 1 5 Attended Features F G Uniform Call Dist
83. Group P G 66 System 2 5 System Timer 2 5 System Timer 2 5 1 System Timer 1 2 Used to assign various system timers 2 4 System Timer 1 2 r Hold Recall Time 0 240 s BEE Call Forwarding Ho Answer Time 1 12 rings B rings r Transfer Recall Time 0 48 rings h2 ring s Extension to CO line Call Duration Time 1 64 min RE Pickup Dial Waiting Time 1 5 s h s CO to CO Line Call Duration Time 1 64 min r Call Duration Count Start Time 0 60 s p ls Automatic Redial Interval Time 30 1200 s First Digit Time 5 120 s _ r Automatic Redial Repeat Times 0 30 times Inter digit Time 1 30 s m fs time s m Door Opener Timer 0 10 s Intercept Time 1 48 rings f2 ring s 2 4 System Timer 1 2 x Parameter Hold Recall Time Default 60 s Value Range 0 240 s Description Function Specifies the length of time in seconds that the system is to wait before alerting the extension user who held the call by Held Call Reminder ringing The reminder tone is emitted every 5 seconds until the held call is retrieved or until the caller hangs up Note If 0 is specified Hold Recall does not occur Reference e 1 13 Audible Tone Features F G Hold Recall System 67 2 5 System Timer Parameter Transfer Recall Time Default 12 rings Value Range
84. KAKTAAKKKKEKAKAAAAAAKKKKKATKKAAAAAKAKAAE fe Header Start Data Start O O Language gt gt Line 1 E Line 4 x Eamets Column M Column C Option 5 15 HOTEL OK Apply Cancel Help Parameter Title Header 3 lines Default Check Out Sheet Value Range Characters consisting of 0 9 A Z a z or the following marks HR lt gt amp Description Function Defines the Title Header format of Check Out Sheet which will be printed out by SMDR Reference None Parameter Header Start Line Default 1 Value Range 1 21 Description Function Specifies the start line of the header Reference None 216 Features 5 15 Hotel Parameter Header Start Column Default 1 Value Range 1 40 Description Function Specifies the start column of the header Reference None Parameter Data Start Line Default 4 Value Range 4 24 Description Function Specifies the start line of the data portion Reference None Parameter Data Start Column Default 1 Value Range 1 40 Description Function Specifies the start column of the data portion Reference None Parameter Language Default English Value Range 1 English 2 Option Description Function Specifies the date display language printed out by SMDR Reference 2 9 Language Data P G 217 5 15 Hotel 218 Features Section 6 Toll Restriction Toll Restriction 219 6 1 Toll Restriction
85. Line 4 2 Trunk Line Parameter TIE Line Sending TIE Caller ID Default No Value Range 1 No 2 Yes Description Function Specifies whether to send or not the TIE Caller ID to the other end Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter TIE Line TIE to CO Security Mode Default No Value Range 1 No 2 Yes Description Function Specifies whether to restrict the TIE to CO call or not If set to Yes the TIE caller must enter a valid TIE User Code before making a CO call via this system Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter DDI DID TIE Digits to delete Default 0 Value Range 0 16 digits Description Function Specifies the number of digits to be deleted from the number received from the DDI DID trunk other PBX via DID TIE lines Reference e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDI e 3 1 E amp M Features F G E amp M TIE Line Service 145 4 2 Trunk Line Parameter DDI DID TIE Number to be added Default Value Range Description Function Reference Blank Max 8 digits consisting of 0 9 Specifies the number 1 to 8 digits to be added to the number received from the DDI DID trunk other PBX via DID TIE lines e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Featu
86. No 20 2 7 System Option 2 4 41 Sending pulse signal during CO call See 16 Duration starting mode Enable C Disable Answer or Time out Answer 12 Automatic adjustment of the clock using 17 Destination Busy DISA Caller ID information Send busy tone Yes Ho C Transferred to IRNA destination 13 DISA prolong operation C Limited 10 times Ho limit 18 Destination Busy DDIDID Send busy tone C Transferred to IRNA destination Send out Dial 14 Dialing in DISA CO to CO talking Disconnect and make a new call Send busy tone m19 Destination Busy TIE C Transferred to IRNA destination r 15 Special dial tone after setting feature 20 Off hook Monitor Enable C Disable Enable Disable 2 7 System Option M oK Apply cancer Heip Parameter 11 Sending pulse signal during CO call Default Enable Value Range 1 Enable 2 Disable Description Function Enables or disables sending pulse dialling signals during an outside call Reference None 82 System 2 8 System Option Parameter 12 Automatic adjustment of the clock using Caller ID information Default No Value Range 1 Yes 2 No Description Function Enables or disables the automatic adjustment of the clock by Caller ID information once a day Reference e 1 5 Attended Features F G Caller ID Service Parameter 13 DISA prolong
87. Paging Tone System Speed Dial TRS Level Override IV Confirmation Tone for Station or External Paging 2 4 Tenant OK Apply Cancel Help Parameter Tenant No Default 1 Value Range 1 8 Description Function Specifies the tenant number which you are going to programme Reference e 1 3 System Features F G Tenant Service Parameter Alert Extension Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the destination extension which will be alerted by the system if there is an extension user who did not respond to the Timed Reminder ringing or Wake Up Call Reference e 1 3 System Features F G Hotel Application 3 2 6 Hotel Use Features Hotel Application KX T7536 KX T7235 only U M System 33 2 2 Tenant Parameter DAY NIGHT Switching Mode Default Manual Value Range 1 Manual 2 Auto Description Function Specifies the Day Night switching mode Manual or Auto 1 Manual The extension allowed by COS Class of Service programming the Manager or the Operators can switch Day Night mode at any time desired by dialling the feature number for Night Mode set cancel 2 Auto The system automatically switches the Day Night mode each day at the time programmed in Auto Start Time Reference e 2 11 4 Switching the Day Night Service U M Parameter Inter tenant Calling 1 8 Default No check Value Range 1 No check Disallowed 2 Check Allowed Description
88. Panasonic Digital Super Hybrid System Programming Guide Moda No KX T D500 C E 1 is Please read this manual before connecting the Digital Super Hybrid System Thank you for purchasing the Panasonic Model KX TD500 Digital Super Hybrid System Introduction This Programming Guide is designed to serve as a technical reference for the Panasonic Digital Super Hybrid System KX TD500 It provides step by step instructions for performing system programming using the Maintenance Console software for a PC About the Other Manuals Along with this Programming Guide the following manuals are available Features Guide Describes every basic optional and programmable features of the KX TD500 System in alphabetical order User Manual Designed for users of Digital Super Hybrid System KX TD500 The focus is Digital Proprietary Telephones DPTs Digital DSS Consoles Single Line Telephones SLTs and their features Installation Manual Describes information necessary for installing the hardware and system maintenance 2 Introduction Table of Contents 1 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 3 1 3 2 3 3 3 4 3 5 3 6 4 4 1 4 2 4 3 4 4 4 5 4 6 4 7 5 5 1 5 2 5 3 5 4 5 5 5 6 Conhgur tion u eine CONMSUP ATION essan sousdstsosedeesessecesasveatsnsvedeiees deacestvedsesusvacesus eee s 6 Slot Assignment s
89. Reference Parameter 72 Remote DND Default 722 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for setting cancelling the DND Do Not Disturb feature for other extensions For Manager Operator only Reference 3 1 2 Setting or Cancelling the DND Feature to Other Extensions Remote DND Control U M 33 2 3 Numbering Plan Parameter 73 Remote FWD Cancel Once Default 723 Value Range 1 4 digits consisting of 0 9 X or Description Function With this feature number the Manager or the Operators can reach an extension that has set Call Forwarding It is one time once cancellation not a permanent cancellation of Call Forwarding on the destination For Manager Operator only Reference e 3 1 3 Calling the Extension that has set Call Forwarding Remote FWD Cancel Once U M Parameter 74 Trunk Route Control Default 724 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for Trunk Route Control For Manager Operator only Reference 3 2 4 Trunk Route Control U M Parameter 75 UCD Monitor Mode Default 725 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for UCD Monitor mode One supervisor can be assigned per UCD Group The supervisor can monitor the number of calls in the waiting queue Reference e 2 11 3 Monitoring the Number o
90. SDN Originating Features F G Calling Line Identification Presentation CLIP 2 3 ISDN Answering Features F G Connected Line Identification Presentation COLP Line 181 4 7 ISDN Extension Line Parameter COS No Primary Default 1 Value Range 1 96 Description Function Spesifies the Primary COS Class of Service number to the ISDN extension Reference e1 3 System Features F G Class of Service COS 3 1 5 Changing Service Level of Extensions Switching COS U M Parameter COS No Secondary Default 1 Value Range 1 96 Description Function Spesifies the Secondary COS Class of Service number to the ISDN extension Reference e1 3 System Features F G Class of Service COS 3 1 5 Changing Service Level of Extensions Switching COS U M 182 Line Section 5 Features Features 183 5 1 Features 5 1 Features Used to assign parameters for various system features ei TD500 Maintenance Console r Programming aie ETE ona Wiel Alone Woe 184 Features 5 2 System Speed Dialling 5 2 System Speed Dialling Used to programme a list of up to 1000 000 999 frequently dialled numbers per tenant Anyone in the same tenant can dial these numbers Up to 2000 Speed Dialling codes can be shared among tenant under the limitation of 1000 codes per tenant The maximum number of Speed Dialling numbers per tenant is specif
91. Specifies the treatment of the invalid TIE calls Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter 24 Sending dial tone to TIE trunk Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether or not the system sends a dial tone to a TIE caller after recognising an incoming TIE call Reference 3 1 E amp M Features F G E amp M TIE Line Service System 89 2 8 System Option Parameter 25 Pressing DSS key operation in CO talking Default Hold Value Range 1 Disconnect 2 Hold Description Function If set to Hold the PT user engaged in a CO call can transfer the current call to another extension simply by pressing the DSS button associated with the destination extension Reference e 1 11 Transferring Features F G One Touch Transfer Parameter 26 Pressing CO key operation in CO talking Default Hold Value Range 1 Disconnect 2 Hold Description Function If set to Hold the PT user engaged in a CO call can with a single operation press a CO key hold the current call and then either get another CO line or answer another CO call Reference e 1 10 Holding Features F G Automatic Hold All Calls Parameter 27 Message Waiting lamp pattern Default 11 Value Range 01 12 Description Function Specifies a light pattern of the Message Lamp of an SLT Note e Message waiting lamp pattern list is provided on Page 87 and Page 88 Ref
92. TAFAS can be specified Notes e A DISA caller can call those extensions simply by dialling a one digit DISA built in Auto Attendant number corresponding to the extension e Assignable only when DISA is specified in OGM Type programming Reference e 1 5 Attended Features F G Direct Inward System Access DISA 130 Group Section 4 Line Line 131 4 1 Line 4 1 Line Used to assign various parameters for both trunk and extension lines TD500 Maintena 132 Line 4 2 Trunk Line 4 2 Trunk Line Used to assign various parameters for trunk lines 4 1 Trunk Line lei ka cwano port no coy Name incoming Type Dial Type Sowno A fom Destination subscriber Mar 16 Digits Dy won fe cd DDVDID TIE Digit to receive DUI Collect Call Digits to delete 0 Enable Disable Humber to be added 4 H Max 6 Digits C Answer Wait Timer Wink Signal lime out start Signal type Hone 1024 ms E l C immediate Wink TIE Line CPC Signal OUT Detection Detection Ti ion Time Disable None H Sensitivity IH IH Detection C Enable Detection Time Hone a Sensitivity ovr Disable Dial Tone Detection gt p Reverse Signal Detection 10 0 Security Mode C Enable Disable C Enable Disable Sending NE Caller ID ox amy ces ueo 4 2 1 Trunk Line Copy Used to copy a part o
93. Then press Reset button 11000 Please set up VPS port in 1 4 VPS DPT Port Assignment screen The attribute s of extension s have been set up as VPS DPT Please set up the port s in 1 4 VPS DPT Port Assignment screen Programming Error Messages 283 11 3 Information Message IXXXX 284 Programming Error Messages Section 12 Default Values Default Values 285 1 Configuration 1 1 Configuration 1 2 Slot Assignment Program Default Card Type Blank Status s 1 3 Trunk Port Assignment Program Default Card No Group No 48 E amp M card 1 Others Status 1 4 Extension Port Assignment Program Default Card No Attribute TEL Tel Type Display only DN 1001 SP NL JT 2001 G Group No 1 Parallel XDP Parallel Status 1 5 VPS DPT Port Assignment Program Default TVP No 1 VPS Card None Type None Jack No Display only Port No Blank 286 Default Values Program Default Ext No 1 DN Blank Ext No 1 Group No Blank Ext No 2 DN Blank Ext No 2 Group No Blank Status 1 6 EI Port Assignment Program Default Card No Channel Type Undefined Group No Blank Receiver Type Undefined Status 1 7 DISA Port
94. Up to 3 digits consisting of 0 9 or Description Function Specifies the Busy Tone code Sent to the VPS when the extension it dialled is busy Reference e 1 3 System Features F G Integration VPS Parameter Reorder Tone Default 3 Value Range Up to 3 digits consisting of 0 9 X or Description Function Specifies the Reorder Tone code Sent to the VPS if it dials an invalid extension number or if it is inadvertently connected to another VPS and so on Reference e 1 3 System Features F G Integration VPS Parameter DND Tone Default 4 Value Range Up to 3 digits consisting of 0 9 X or Description Function Specifies the DND Tone code Sent to the VPS if the extension it dialled is in DND mode Reference e 1 3 System Features F G Integration VPS Parameter Extension Answer Default 5 Value Range Up to 3 digits consisting of 0 9 X or Description Function Specifies the Extension Answer code Sent to the VPS when the extension it dialled answers the call Reference e 1 3 System Features F G Integration VPS 198 Features 5 10 VPS Integration Parameter Extension Disconnection Default 9 Value Range Up to 3 digits consisting of 0 9 X or Description Function Specifies the Extension Disconnection code Sent to the VPS when the calling party hangs up Reference e 1 3 System Features F G Integration VPS Parameter Confirmation Tone Default 9 Value Range Up to 3 digits co
95. Value Range 1 8 Description Function Specifies a tenant number 1 8 to which the trunk group is assigned This setting is required when Tenant Service is employed Reference e 1 3 System Features F G Tenant Service 2 2 Tenant P G Parameter Intercept Destination Day Night Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the destination extension 3 or 4 digits for Intercept Routing feature in both Day and Night modes respectively Note e Intercept Routing provides an automatic re direction of calls that have not been answered Reference e 1 11 Transferring Features F G Intercept Routing 105 3 2 Trunk Group Parameter Line Hunting Order Default Normal Value Range 1 Normal 2 Reverse 3 Sequential Description Function Specifies the hunting sequence of idle lines on a trunk group basis 1 Normal The system connects the user to an idle trunk line with the lowest physical number 2 Reverse The system connects the user to an idle trunk line with the highest physical number 3 Sequential To avoid repeated use of the same trunk line rotation is performed in numerical order from the lowest to the highest trunk port physical number Busy lines are skipped of course Reference 2 8 System Option P G Parameter Disconnecting Time Default 1 5 s SP NL JT 2 0 s G Value Range 1 0 58 2 1 5s 3 2 08 4 4 05 5 12 0 s Description Function Spe
96. Wake Up Call e 2 7 1 Setting the Alarm Timed Reminder Wake Up Call U M e 3 1 1 Setting the Alarm for Other Extensions Remote Timed Reminder Wake Up Call U M System 75 2 6 Local Hunt Sequence 2 6 Local Hunt Sequence Specifies the trunk group hunt sequence to be used when an extension user attempts to make an outside call by dialling the feature number for Local CO Line Access ARS or by pressing a Loop CO key Hunting Trunk Order Group No 17 Hone 25 Mone 33 Ka Ka 06 Hone 14 Hone v o2 none 10 None 18 none z 26 mone 34 None z 4 one 03 Hone x 1 Hone gt 19 Hone x 27 Hone gt 35 Hone B Hone 04 Hone v 12 Hone v 20 hone 28 None z 36 None 44 none 05 Hone 13 hone 21 None v 29 None 37 None 45 46 22 NHone 30 None 38 07 None 15 23 None 31 None v 39 a Hone v HH 4 HH 08 None 16 KAENI HHH HUHN o o o gt 2 m m 24 None 32 None v 40 2 5 Local Hunt Sequence xl OK Apply Cancel Help Parameter Trunk Group No Default 01 1 Others None Value Range None 1 48 Description Function Specifies the trunk group 1 48 in hunting order Notes e Local Hunt Sequence works only if ARS Automatic Route Selection mode is turned off e The sequence can be used by any extension user in the system regardles
97. Your Conversation Executive Busy Override Deny U M Parameter 47 Pickup Dialing Program Set Cancel Default 74 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for programming setting cancelling Pickup Dialling feature Reference 2 2 2 Easy Dialling U M Parameter 48 Absent Message Set Cancel Default 750 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for setting cancelling Absent Message feature Reference e 2 5 3 Showing an Absent Message on the Caller s Telephone Display Absent Message Capability U M Parameter 49 Timed Reminder Confirm Set Cancel Default 761 SP NL JT 76 G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for confirming setting cancelling Timed Reminder feature Reference e 2 7 1 Setting the Alarm Timed Reminder Wake Up Call U M 49 2 3 Numbering Plan Parameter 50 Station Lock Set Cancel Default 762 SP NL JT 77 G Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for setting cancelling Electronic Station Lockout feature Reference e 2 5 4 Preventing Other People from Using Your Telephone Electronic Station Lockout U M Parameter 51 Night Mode Set Cancel Default 78 Value Range 1 4 digits consisting of 0
98. able Print out Check in Check out Disable 10 5 Power Failure Transfer Program Default Trunk Card 1 24 None Extension Card 1 24 None 10 6 System Parameters Program Default Password System Programming 1234 310 Default Values Program Default Password User Programming 1234 Password Walking COS 1234 Serial Interface Port PROG Port 1 Serial Interface Port PROG Parity Display only Serial Interface Port PROG NL Code CR LF Serial Interface Port PROG Word Length Display only Serial Interface Port PROG Stop Bit Display only Serial Interface Port PROG Baud Rate 19200 bps Serial Interface Port SMDR Port 2 Serial Interface Port SMDR Parity None Serial Interface Port SMDR NL Code CR LF Serial Interface Port SMDR Word Length 8 bits Serial Interface Port SMDR Stop Bit 1 bit Serial Interface Port SMDR Baud Rate 9600 bps Remote FDN Blank 10 7 System Time Program Default System Time Year 00 Month Jan Day 01 Day of the week Sat Hour 12 Minute 00 AM PM AM Default Values 311 11 Programming Error Messages 11 1 Error Messages EXXXX 11 2 Warning Messages WXXXX 11 3 Information Message IXXXX 312 Default Values Default Values 313 Copyright This manual is copyrighted by Kyushu Matsushita
99. all to the Intercept Routing destination is not answered before this timer expires the call will be disconnected Reference e 1 11 Transferring Features F G Call Forwarding e 2 5 1 Forwarding Your Calls Call Forwarding U M Parameter Extension to CO Line Call Duration Time Default 10 min Value Range 1 64 min Description Function Specifies the maximum time allowed for a call with an outside party This time limit can apply to outgoing CO calls only or both outgoing and incoming CO calls This is determined by 5 Limited call duration setting in Section 2 8 System Option Note e This timer applies to the extension user who is restricted by Time Limit of Outside Calls setting in Section 2 4 Class of Service COS Reference None Parameter CO to CO Line Call Duration Time Default 10 min Value Range 1 64 min Description Function Specifies the maximum time allowed for a call between two outside parties CO to CO line call If this timer expires during a CO to CO line call it will be disconnected Reference e 1 5 Attended Features F G Direct Inward System Access DISA 70 System 2 5 System Timer Parameter Automatic Redial Interval Time Default 60 s Value Range 30 1200 s Description Function Specifies the interval time between each Automatic Redial attempt Reference e 1 7 Dialling Features F G Redial Automatic Parameter Automatic Redial Repeat Times Default 10 times SP G
100. alue Range 1 Default 2 Unknown 3 ISDN Telephony 4 National Standard 5 Private Description Function Specifies the Numbering Plan ID applied to the incoming CO calls via ISDN Private Network Reference None Parameter Type of Number Outgoing Public Default Default Value Range 1 Default 2 Unknown 3 International 4 National 5 Network Specific 6 Subscriber Description Function Specifies the Type of Number applied to the outgoing CO calls via ISDN Public Network Reference None 112 Group 3 2 Trunk Group Parameter Type of Number Outgoing Private Default Default Value Range 1 Default 2 Unknown 3 International 4 National 5 Network Specific 6 Subscriber Description Function Specifies the Type of Number applied to the outgoing CO calls via ISDN Private Network Reference None Parameter Type of Number Incoming Public Default Default Value Range 1 Default 2 Unknown 3 International 4 National 5 Network Specific 6 Subscriber Description Function Specifies the Type of Number applied to the incoming CO calls via ISDN Public Network Reference None Parameter Type of Number Incoming Private Default Default Value Range 1 Default 2 Unknown 3 International 4 National 5 Network Specific 6 Subscriber Description Function Specifies the Type of Number applied to the incoming CO calls via ISDN Private Network Reference None Group 113 3 3 Extension Group
101. ank Default Values 303 Program Default TRS Level None 5 7 Special Carrier Code Program Default Code Blank 5 8 Absent Message Program Default Message MSGI Will Return Soon MSG2 Gone Home MSG3 At Ext Extension No MSG4 Back at Hour Minute MSGS Out Until Day Month SP NL JT Month Day G MSG6 In a Meeting MSG7 9 Blank 5 9 DISA TIE User Code Program Default Code All Blank COS All 96 5 10 VPS Integration 5 10 1 VPS Integration 1 2 Program Default Integration Code Ringback Tone Busy Tone Reorder Tone DND Tone Extension Answer Extension Disconnection Confirmation Tone 304 Default Values Program Default FWD to VM Ringback Tone 6 FWD to VM Busy Tone 7 FWD to Extension Ringback Tone 8 Voice Mail Command Leave Message H Get Message H AA Service 8 VM Service 6 5 10 2 VPS Integration 2 2 Program Default DTMF signal duration 80 ms Pause timing before sending DTMF signal 1 5s Follow on ID Pause timing before sending DTMF signal RBT 1 5 s BT Turn off control of Message Waiting lamp System Start AA service after FWD IRNA of CO call Do not start Extension s mailbox number Programmed number
102. ator services such as Check in Check out Reference e 1 3 System Features F G Hotel Application Parameter 45 Flash Signal before CO Disconnect Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether or not the system sends the FLASH signal to the Central Office after the CO call is terminated Used to receive pay tones after the termination of the call Reference None Parameter 46 Date Display Default D M Y SP NL JT M D Y G Value Range 1 M D Y 2 D M Y Description Function Specifies a date display format appropriate to your area Reference e 1 17 Display Features F G Display Date and Time Parameter 47 Tone Type for Outgoing Calls Default Busy Reorder Value Range 1 Busy Reorder 2 Busy 3 Reorder Description Function Specifies a tone type for outgoing calls Reference None 96 System 2 8 System Option Parameter 48 Call Pickup with DSS S CO key Default Disable Value Range 1 Enable 2 Disable Description Function By default an S CO button assigned to a DSS button on a DSS Console is available for monitoring the call activity only not available for making receiving a call If this parameter is enabled an S CO button on a DSS Console can be used to answer the incoming CO call on the S CO button and retrieve the CO call held on the S CO button Reference e 1 16 Button Features F G Button Line Access Parameter 49 LCD D
103. ax Dial No after EFA Signal ooy fmon Som o b a Line Hunting Order Tenant No Flash Time Hormal 1 80 ms x Disconnecting Time Pause Time PBX Access Code ss s JO U VW Numbering Plan ID Public Private PBX Dial Tone Outgoing erautt E Diuk E Enable Disable wem acon sf ownor gt POR RresToe Enable Disable p poot a ae Private 7 Orele See Betten IV Continuous Signal Detection Incoming Default l Default z I Silence Detection 3 1 Trunk Group M Apply Cancel Help 3 2 1 Trunk Group Copy Used to copy a part of or all settings of a certain Trunk Group to all other Trunk Groups at a time You can also specify one or several Trunk Groups as the copy destination Copying the Trunk Group Parameters to Other Trunk Groups 1 Edit the parameters of the copy source Trunk Group and save it 2 Point to the Copy button on 3 1 Trunk Group screen of the copy source and click e Trunk Group Copy screen is displayed e The current Trunk Group copy source number is shown as Copy from Trunk Group 1 48 Group 103 3 2 Trunk Group Copy from Trunk Group 1 r Copy item Destination Trunk Group ro 113 13 137 m o2 14 M 26 38 Iv Fes pial Tona rs Ts Da 39 IV Line Hunting Order IV Tenant No a a a a IV Disconnecting Time 05 47 29 ra IV Pause Time T 06 18 T 30 2 IV Pause Time Before Flash Signal ro M19 ra rs IV Feen Tima rs ra
104. ber for making an outside call by ARS Automatic Route Selection or Trunk Access Idle Reference e 2 2 1 Basic Calling U M Parameter 19 Trunk Group Access Default 8 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for making an outside call by specifying a Trunk Group 01 48 Reference e 2 2 1 Basic Calling U M 42 System 2 3 Numbering Plan Parameter 20 Speed Dialing System Default k Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for making a call using a System Speed Dialling number Reference 2 2 2 Easy Dialling U M Parameter 21 Speed Dialing Station Default 3 SP NL JT 6 G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for making a call using a Station Speed Dialling number Reference e 2 2 2 Easy Dialling U M Parameter 22 Speed Dialing Station Programming Default 30 SP NL JT 60 G Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for programming Station Speed Dialling numbers at each extension Reference e 2 2 2 Easy Dialling U M Parameter 23 Doorphone Call Default 31 SP NL JT 68 G Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for making a call to a doorphone
105. c Voice Processing System one that supports DPT Integration is connected to the extension port 1 5 VPS DPT Port Assignment P G 4 3 Extension Line P G 44 DSS Console P G Configuration 13 1 4 Extension Port Assignment Parameter Tel Type Default Value Range Description Function Reference Display only Please refer to Description Function Displays the model number of telephone set which is currently connected to the extension port lt Telephone type list gt Unknown Not connected or Single Line Telephone T7020 APT with SP PHONE 12 CO T7030 APT with SP PHONE 1 Line Display 12 CO T7050 APT with MONITOR 12 CO T7130 APT with SP PHONE 1 Line Display 12 CO T7320 APT with SP PHONE 12 CO T7330 APT with SP PHONE 1 Line Display 12 CO T7350 APT with MONITOR 12 CO T7220 DPT with SP PHONE 24 CO T7230 DPT with SP PHONE 2 Line Display 24 CO T7235 DPT with SP PHONE 6 Line Display 12 CO T7250 DPT with MONITOR 6 CO T7451 DPT with MONITOR 4 CO T7531 DPT with SP PHONE 1 Line Display 12 CO T7533 DPT with SP PHONE 3 Line Display 12 CO T7536 DPT with SP PHONE 6 Line Display 12 CO T7550 DPT with MONITOR 12 CO T7040 DSS Console 32 DSS 16 PF T7240 DSS Console 32 DSS 16 PF T7540 DSS Console 66 DSS T7541 DSS Console with ANSWER and RELEASE buttons 48 DSS Note e Some telephones in the above list are not
106. ce 3 FAULT The extension port is defective Reference None 16 Configuration 1 5 VPS DPT Port Assignment 1 5 VPS DPT Port Assignment Used to assign parameters for VPS DPT ports Up to eight Panasonic Voice Processing Systems VPSs can be connected to the system 1 4 VPS DPT Port Assignment Bee rw ve Iz wscws one we ww gt Ext No 1 Ext Ho 2 Jack No Port Ho DH Group Ho DH Group Ho pa e e e ros a s gt of Pe fe foes ras ms DH Refer ox sony cance nen How to set upa TVP 1 Assignment of the card which will be connected to the VPS System e When you use anew DLC DHLC card and set up the TVP to the PBX Assign the card type of the slot to be installed to DLC or DHLC card and change the card status to INS In Service in 1 1 Slot Assignment screen Then see the information of Card Properties and confirm that the software version of the card shows more than 1 e When you connect the TVP to the existing DLC DHLC Go to step 2 2 Assignment of the port which will be connected to the VPS System Change the attribute of the port to be connected to the TVP to VPS DPT in 1 3 Extension Port Assignment screen When the attribute of the port is changed to VPS DPT the parameters except Attribute will disappear and the directory number will be purged 3 Assignment of VPS card and its model Select the corresponding equipment number in
107. cifies the maximum time in seconds the system is to wait after releasing the trunk line before getting it again Note e This allows the Central Office an opportunity to release its resources before another trunk call is placed from the PBX Reference None 106 Group 3 2 Trunk Group Parameter Pause Time Default 1 5 s SP NL 3 5 s JT G Value Range 1 1 5s 2 2 58 3 358 4 455 Description Function Specifies the length of pause time dialling delay The programmed pause time is automatically inserted after a line access code or a host PBX access code or manually inserted if the PAUSE button is pressed by the extension user Reference e 1 3 System Features F G Host PBX Access 2 8 2 If a Host PBX is Connected U M Parameter Pause Time before Flash Signal Default 512 ms Value Range 1 None 2 512 ms 3 1024 ms 4 1536 ms 5 2048 ms Description Function Specifies the pausing time required before sending the Flash Signal Reference None Group 107 3 2 Trunk Group Parameter Flash Time Default Value Range Description Function Reference 80 ms SP NL JT 300 ms G None 80 ms 300 ms 600 ms 900 ms 1200 ms AWAY NE Specifies the length of flash time Notes e In some countries the ELCOT card must not be connected to the Public Switched Network e When you need finer resolution assign this to 80 ms and use Flash Time parameter in
108. ckup Deny mode Reference e 1 9 Answering Features F G Call Pickup e 2 7 8 Denying Other People the Possibility of Picking up Your Calls Call Pickup Deny U M Parameter Language Default English Value Range 1 English 2 Option Description Function Specifies the language shown on a PANASONIC display PT The language is set for each extension so phones on the same system can display different languages Note e French is stored as default Optional Language at the factory Dutch Spanish or Portuguese can be uploaded to the system instead of French Please refer to Section 2 9 Language Data for further information on Optional Language Reference e 4 1 1 Initial Settings U M Parameter Station Lock Password Default Blank Value Range Fixed to 3 digits consisting of 0 9 Description Function Specifies the 3 digit password that lets the extension user lock and unlock the extension Electronic Station Lockout Reference e 1 6 Originating Features F G Call Pickup e 2 5 4 Preventing Other People from Using Your Telephone Electronic Station Lockout U M 157 4 3 Extension Line Parameter CLIP COLP Number Public Default Value Range Description Function Reference Blank Up to 16 digits consisting of 0 9 X or P PAUSE Specifies a CLIP COLP number used for the incoming outgoing calls via Public Network to each extension Note e The KX TD500 System is designed and manufactured in acco
109. consisting of 0 9 X or Specifies the feature number for answering a CO call ringing at another extension e 2 3 3 Answering a Call Ringing at Another Telephone Call Pickup U M 44 System 2 3 Numbering Plan Parameter 29 Group Call Pickup Default 40 Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for answering a call ringing at another extension in the same Extension Group Reference e 2 3 3 Answering a Call Ringing at Another Telephone Call Pickup U M Parameter 30 Directed Call Pickup Default 41 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for answering a call ringing at another extension Reference e 2 3 3 Answering a Call Ringing at Another Telephone Call Pickup U M Parameter 31 Hold Default 50 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for putting a call on hold Reference e 2 4 1 Holding a Call U M Parameter 32 Hold Retrieve Station Default 51 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for retrieving a call held at another extension Reference e 2 4 1 Holding a Call U M 45 2 3 Numbering Plan Parameter 33 Hold Retrieve Trunk Default 53 Value Range 1 4 digits consisting of 0 9 X or Descript
110. cription Function Specifies the Trunk Group 1 48 to which the PRI port is assigned Reference e 1 3 System Features F G Trunk Group 3 2 Trunk Group P G Parameter Status Default Value Range 1 INS 2 OUS 3 FAULT Description Function Specifies the operating status of each PRI port 1 INS The PRI port is In Service 2 OUS The PRI port is Out of Service 3 FAULT The PRI port is defective hardware In this case the LED indicator on the PRI30 card will light Reference None Configuration 29 1 9 PRI Port Assignment 30 Configuration Section 2 System System 31 2 1 System 2 1 System Used to assign parameters which affect system wide operation 32 System 2 2 Tenant 2 2 Tenant Used to assign various parameters on a tenant 1 8 basis 2 1 Tenant ae Alert Extension me E me C Je m O DAY NIGHT Switching Mode Inter tenant Calling l Manual C Auto or g 8 so st a Day1 Hight Day2 Hight2 Tue os oo aM E os fpo PM A eo jo Disable E 00 fo Disable E wef ox Frm Po oso a orm a Thu 09 foo AM a os oo PM a po foo Disable E foo foo Disable E sat os oo Mm E os EPs rm E oo 00 fnisabie Fl oo Disable Music on Hold Source BGM S i ries Max 2 Ll3 i is 1 i Le mus Must 1000 Automatic Route Selection IV External
111. de 6 3 TRS Exception Code Used to programme a list of numbers that an extension is allowed to dial even if these numbers are listed in a TRS Deny Code Table Up to 200 TRS Exception codes can be assigned 6 2 TRS Exception Code TRS Level Entry No No Dial Max 10 Digits oo yn om WO Aa vn an Parameter TRS Level Default 6 Value Range 2 6 Description Function Specifies a TRS toll restriction level Reference e 1 6 Originating Features F G Toll Restriction Parameter Entry No Default 001 020 Value Range 001 200 in 20 entries increments Description Function Specifies a unit of 20 TRS Exception codes which apply to the TRS level selected Reference e 1 6 Originating Features F G Toll Restriction Toll Restriction 223 6 3 TRS Exception Code Parameter Dial Default Blank SP NL JT XXXXXXX G Level 2 only Value Range Up to 10 digits consisting of 0 9 X X or Description Function Specifies the leading 10 digits of the telephone numbers which are excepted from the toll restriction Note e X can be used as a wild card character which substitutes any digit in its position Reference e 1 6 Originating Features F G Toll Restriction 224 Toll Restriction Section 7 ARS Automatic Route Selection ARS Automatic Route Selection 225 7 1 ARS Automatic Route Selection 7 1 ARS Automatic Route Selecti
112. displayed depending on the destination area e 1 3 System Features F G Mixed Station Capabilities 14 Configuration 1 4 Extension Port Assignment Parameter DN Default 1001 SP NL JT 2001 G Value Range 3 4 digits consisting of 0 9 Description Function Specifies the DN Directory Number extension number for the extension port Note e You must assign the paired extension for DN after selecting DSS for the attribute Reference 2 3 Numbering Plan P G Parameter Group No Default 1 Value Range 1 128 Description Function Specifies the Extension Group 1 128 to which the extension port is assigned Note e Group No of the first extension is assigned to 128 Reference 1 3 System Features F G Extension Group 3 3 Extension Group P G Parameter Parallel XDP Default Parallel Value Range 1 Parallel 2 XDP Description Function Specifies whether to enable or disable Parallelled Connection of PT and SLT or XDP eXtra Device Port Connection of DPT and SLT Reference e 1 1 System Expansion F G EXtra Device Port XDP e 1 3 System Features F G Parallelled Telephone Configuration 15 1 4 Extension Port Assignment Parameter Status Default Value Range 1 INS 2 OUS 3 FAULT Description Function Specifies the operating status of the extension port 1 INS The extension port is In Service 2 OUS The extension port is Out of Servi
113. during Day Night mode respectively Reference e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDD Parameter Name Default Blank Value Range Up to 10 characters consisting of 0 9 A Z a z or the following marks x lt gt amp Description Function Specifies the name for the destination extension where a DDI DID call comes in Reference e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDI DDI DID 9 2 Number Transformation Parameter MSN Line No Default Blank Value Range Physical number of the trunk port Description Function Specifies the physical number of the trunk port This port will be used to forward a call by ISDN Line Reference e 2 4 ISDN Attended Features F G Multiple Subscriber Number MSN Ringing Service 9 2 2 Automatic Registration of DDI DID MSN Numbers Provides quick registration of DDI DID MSN numbers Up to 100 entries can be registered at once with a simple operation 1 Click Auto Registration button on 9 1 Number Transformation screen e Automatic Registration screen is displayed Automatic Registration Base Number Dial Max 15 digits Additional Number Number of Registrations 10 Humber of Digits 2 Beginning Entry No 1 991 i bel u 2 En
114. e e If the charge limit is set to 0 no restriction is applied Reference e 4 2 Charge Fee Management Station Programming U M Parameter JOG Dial Speed Default Normal Value Range 1 Normal 2 High Description Function Specifies the rotation speed of the JOG Dial on the KX T7500 series PT Reference None Parameter ISDN Bearer Mode Default Automatic Value Range 1 Automatic 2 Speech 3 3 1 KHz Audio Description Function Specifies the ISDN Bearer Mode on an extension basis Note e When Automatic Default is selected Bearer Mode is set automatically depending on the type of extension telephone as follows PT Speech SLT 3 1KHz Audio ISDN extension depending on the bearer mode of the ISDN extension Reference e 2 1 ISDN Features F G Integrated Services Digital Network ISDN Line 159 4 3 Extension Line 4 3 2 Flexible CO Key Assignment Used to determine the usage of flexible CO buttons on PTs The following screen is displayed by clicking CO Key button on 4 2 Extension Line screen EXT1001 a ae ee es a ae __Hot stored Not stored Not Stored Notstorea _Notstorea Not Stored oma um lt Key Type Assignment gt The following Key Type Assignment screen is displayed by clicking Not Stored button for each CO key on the above screen honk Line iG Ubi ungingiype Immediate Coneei _ Heip 160 Line 4 3 Extension Line lt Additional Para
115. e Deny Default Enable Value Range 1 Enable 2 Disable Description Function Enables or disables Executive Busy Override Deny feature Note e Executive Busy Override Deny allows the extension user to prevent Executive Busy Override from being executed by another extension user Reference e 2 7 9 Denying Other People the Possibility of Joining Your Conversation Executive Busy Override Deny U M 60 System 2 4 Class of Service COS Parameter DND Override Default Disable Value Range 1 Enable 2 Disable Description Function Enables or disables DND Override feature Reference 2 2 5 Calling without Restrictions U M Parameter Digits Restriction in CO Talk Mode Default Unrestricted Value Range 1 Unrestricted 2 1 15 the digits to be dialled out Description Function Specifies the maximum number of digits that can be dialled during a CO call If the outside party hangs up during a CO call and the extension user tries to dial out while still on the same CO line the system will disconnect the line at the instant the assigned number of digits are dialled Note e This programme can be added if the CPC Signal Detection is not provided by the Central Office Reference e 1 3 System Features F G Calling Party Control CPC Signal Detection Parameter Call from TRS Level 7 Extension Default Enable Value Range 1 Enable 2 Disable Description Function If set to Enable TRS level 7 exte
116. e None Parameter Name Default Blank Value Range Up to 16 characters consisting of 0 9 A Z a z or the following marks x 3 lt gt 7 amp Description Function Specifies the name to a Caller ID code Note e With Caller ID Service the calling party is displayed either by its ID Code or by its name If the name display is required use this programme to give a name to a Caller ID code Reference e 2 10 1 Calling Using the Call Log Incoming Call Log KX T7533 KX T7536 KX T7230 KX T7235 only U M Parameter Number Default Blank Value Range Up to 24 digits consisting of 0 9 x or Description Function Specifies the identification code of the calling party Caller ID code to utilise Caller ID Service Reference e 2 10 1 Calling Using the Call Log Incoming Call Log KX T7533 KX T7536 KX T7230 KX T7235 only U M Features 5 13 UCD Time Table 5 13 UCD Time Table If all extensions in a UCD group are busy the incoming CO calls will be handled by the UCD Time Table procedure Up to 32 UCD Time Tables max 16 steps for each can be assigned 5 13 UCD Time Table TableNo ME Command Sequence 4 at 5 hone 9 hone 13 None gt 2 None 6 None 10 None 14 None gt 3 hone z None 11 None 15 None 4 hone 8 sone 12 None 16 None UN Ls 5 13 UCD Time Table M OK Apply Cancel Help
117. e Numbering Parameter 8 8th Hundred Block Extension Default 22 SP NL JT 32 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering Parameter 9 9th Hundred Block Extension Default 23 SP NL JT 33 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering Parameter 10 10th Hundred Block Extension Default 24 SP NL JT 34 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering System 41 2 3 Numbering Plan Parameter 11 16 11th Hundred Block Extension 16th Hundred Block Extension Default Blank Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering Parameter 17 Operator Call Default 0 SP 9 NL JT G Value Range 1 4 digits consisting of 0 9 x or Description Function Specifies the feature number for calling the Operator FDN for each Operator Group can also be used for this purpose Reference e 2 2 1 Basic Calling U M Parameter 18 Local CO Line Access ARS Default 9 SP 0 NL JT G Value Range 1 4 digits consisting of 0 9 x or Description Function Specifies the feature num
118. e e 1 8 Ringing Features F G Do Not Disturb DND e 1 11 Transferring Features F G Call Forwarding Parameter 34 ELCOT LCOT Busy out Loop Relay Default OFF Value Range 1 ON 2 OFF Description Function When a CO line is busied out manually by the Manager an Operator the state of Loop Relay is controled by this setting Note e In some countries the ELCOT card must not be connected to the Public Switched Network Reference e 1 3 System Features F G Trunk Busy out Parameter 36 Tone Mode Default Type 1 SP NL G Type 7 JT Value Range 1 Type 1 2 Type 2 3 Type 3 4 Type 4 5 Type 5 6 Type 6 7 Type 7 Description Function Specifies the Tone output type Note e The change of this parameter is activated after resetting the system Reference None System 93 2 8 System Option Parameter 37 Ring Mode Default Type 6 SP Type 1 NL G Type 5 JT Value Range 1 Type 1 2 Type 2 3 Type 3 4 Type 4 5 Type 5 6 Type 6 Description Function Specifies the Rigning Tone type Note e The change of this parameter is activated after resetting the system Reference None Parameter 38 First Digit Time out Process Default Don t release the trunk Value Range 1 Release the trunk 2 Don t release the trunk Description Function Specifies the treatment of the trunk line when no digits are dialled before the First Digit timer expires Reference None Parameter 39 Exten
119. e number of lines per page Used to match the SMDR output to the paper size being used in the printer Reference None Maintenance 233 10 4 SMDR Parameter Format Skip Perforation Default 0 Value Range 0 95 lines Description Function Determines the number of lines to be skipped at the end of every page The number of lines to skip is simply the number specified in this parameter The number of lines printed is the difference between the Page Length number and the Skip Perforation number Reference None Parameter Duration Log Outgoing Calls Default All Value Range 1 None 2 All 3 Toll Only Description Function Specifies the type of outgoing calls which will be printed out by SMDR 1 None No printout 2 All All calls 3 Toll Only Toll calls only Reference None Parameter Duration Log Incoming Calls Default On Value Range 1 On 2 Off Description Function Specifies whether or not incoming calls will be printed out by SMDR 1 On All calls 2 Off No printout Reference None Maintenance 10 4 SMDR Parameter Priority of Caller ID information Default Number Value Range 1 Number 2 Name Description Function SMDR can print out Caller ID information This setting specifies whether priority is given to Caller ID Name or to Caller ID Number However SMDR can print out both when Type D is specified as Output Type Reference e 1 5 Attended Feat
120. e numbers can be from 1 to 4 digits and shouldn t be any conflicts The following are examples of feature number conflicts Examples N and NX NXX NM and NML NL is allowed E2011 Out of range Overflow Timer should be assigned in the range of Second 5 180 None shows that Overflow Timer doesn t work E2012 Trunk group number duplicated Each trunk group in the Local Hunt Sequence must have a unique number E3001 Invalid directory number for intercept destination There are five possible destinations for intercepted calls 1 An extension 2 an external pager TAFAS 3 an OGM group 4 an extension group or 5 a phantom extension E3002 Invalid directory number for overflow destination Only DN of an extension or FDN of an extension group can be assigned as an overflow destination However the type of DN FDN assignable depends on Group Type E3003 Invalid directory number for UCD supervisor extension Only DN of an extension can be assigned as UCD supervisor extension E3004 Extension group number duplicated Each extension group in the same paging group must have a unique number E3005 The extension group already belongs to another paging group An extension group cannot belong to two or more paging groups E3006 Invalid directory number for DIL1 N destination Only DN of an extension or FDN of an extension group can be assigned as a DIL 1 N destination E3008 Invalid directory number
121. ecifies the TRS toll restriction level for each account code Note e TRS level appended to each account code applies to the call in conjunction with Toll Restriction by Account Code Entry feature Reference e 1 3 System Features F G Account Code Entry e 1 6 Originating Features F G Toll Restriction Override by Account Code Entry 2 2 5 Calling without Restrictions U M Features 191 5 7 Special Carrier Code 5 7 Special Carrier Code Used to programme a list of up to 100 Special Carrier Codes f o sn oo v o a a Lo A N gt gt A o III OTT TTT HIN a E 2 8 2 BR amp 6e88 8 8 mu nd EEE k 5 6 Special Carrier Code i l y _Sancet Parameter Code Default Blank Value Range Up to 10 digits consisting of 0 9 x or X Description Function Specifies special carrier access codes Notes e This assignment allows the system to recognise the user dialled special carrier code in order to insert the necessary pause and to apply toll restriction e X can be used as a wild card character which substitutes any digit in its position Reference e 1 6 Originating Features F G Toll Restriction 192 Features 5 8 Absent Message 5 8 Absent Message Used to programme a list of up to nine absent messages An absent message if set by the extension user is displayed on the calling ext
122. ect and hear CO dial tone JT G Default Values 293 Program Default 5 Limited call duration Both calls 6 Transfer recall destination Originating extension 7 Checking dial by toll restriction Check 8 Confirmation tone for Override Barge in Enable Conference and Privacy Release 9 Confirmation tone for Call Pickup Paging Enable Answer TAFAS Answer Hold Retrieve and Call Park Retrieve 10 Station Speed Dialing Initial display Name 2 8 2 System Option 2 4 Program Default 11 Sending pulse signal during CO call Enable 12 Automatic adjustment of the clock using No Caller ID information 13 DISA prolong operation No limit 14 Dialing in DISA CO to CO talking Disconnect and make a new call 15 Special dial tone after setting feature Enable 16 Duration starting mode Answer or Time out 17 Destination Busy DISA Send busy tone 18 Destination Busy DDI DID Send busy tone 19 Destination Busy TIE Send busy tone 20 Off hook Monitor Enable 2 8 3 System Option 3 4 Program Default 21 Illegal Number DISA Send reorder tone 22 Ilegal Number DDI DID Send reorder tone 23 Ilegal Number TIE Send reorder tone 24 Sending dial tone to TIE trunk Disable 25 Pressing DSS key operation in CO talking Hold 26 Pressing CO key operation in CO ta
123. ension s display PT to show the reason of absence no answer No Message Max 16 Characters a 2 ee 5 8 Absent message ok apiy Cancer Help Features 193 5 8 Absent Message Parameter Message Default Value Range Description Function Reference MSGI Will Return Soon MSG2 Gone Home MSG3 At Ext Extension No MSG4 Back at Hour Minute MSGS Out Until Day Month SP NL JT Month Day G MSG6 In a Meeting MSG7 9 Blank Up to 16 characters consisting of 0 9 A Z a z or the following marks x 3 lt gt 7 amp Specifies Absent Messages Messages through 6 are programmed at the factory but can be changed Note e If Print out Absent Message 6 9 Section 10 4 SMDR is enabled by System Programming Absent Messages No 6 to No 9 will be printed out by SMDR when an extension user specifies one of these messages by dialling the feature number for Absent Message e 1 17 Display Features F G Absent Message Capability 2 5 3 Showing an Absent Message on the Caller s Telephone Display Absent Message Capability U M 194 Features 5 9 DISA TIE User Code 5 9 DISA TIE User Code Used to programme a list of up to 32 DISA TIE User Codes Each code is appended with a COS level 5 9 DISA TIE User Code Bee Code No 4 10 Digits cos gt Tm HHHN ll
124. er or feature access number up to 24 digits consisting of 0 9 x P S or F Note P Pause S Secret Dialling F Hook Flash VTR DN Specifies the Directory Number of the Voice Mail extension 2WAY REC DN Specifies the Directory Number of the Voice Mail extension 2WAY TRN DN Specifies the Directory Number of the Voice Mail extension Line 161 4 3 Extension Line Additional Key Type Parameters Description default SS Dial Specifies the telephone number or feature access number up to 24 digits consisting of 0 9 x P S or F Note P Pause S Secret Dialling F Hook Flash 162 Line 4 3 Extension Line Parameter Key Type Default Value Range Description Function Reference CO 01 Loop CO Others Not Stored Please refer to Description Function Not Stored Key Type is not assigned SINGLE CO Single CO button GROUP CO Group CO button LOOP CO Loop CO button DSS Direct Station Selection button PHANTOM Phantom button PDN Primary Directory Number button SDN Secondary Directory Number button ONE TOUCH One Touch Dial button MESSAGE Message Waiting button FWD DND Call Forwarding Do Not Disturb button SAVE Saved Number Redial button ACCOUNT Account Code entry button CONF Conference button VTR Voice Mail Transfer button LOGIN LOGOUT Login Logout button 2WAY REC Two way Recording button 2WAY TRN Two way Transfe
125. erence e 1 17 Display Features F G Message Waiting e 2 2 4 When the Dialled Line is Busy or There is No Answer U M System 2 8 System Option Parameter 28 Trunk hunting mode Default Value Range Description Function Reference Forced 1 Forced 2 Loop Detection Specifies the trunk hunting mode 1 Forced The system seizes a trunk line whether or not loop current is detected from the local CO 2 Loop Detection The system seizes a trunk line after detecting loop current from the local CO 3 2 Trunk Group P G Parameter 30 Net CODEC Default Value Range Description Function Reference A law 1 law 2 A law Specifies the type of PCM Pulse Code Modulation conversion mode compatible with the Digital Network to which the system is connected Note e The change of this parameter is activated after resetting the system None 2 8 4 System Option 4 4 Used to assign system option parameters No 31 No 49 System 91 2 8 System Option 2 7 System Option 4 4 BEE 31 Answering Call Waiting call by SLT hooking 32 Whisper OHCA to extensions other than Enable Disable TPATERX m Enable G Disable 33 FWD DHD lamp pattern 34 ELCOT LCOT Busy out Loop ty orr E 36 Tone Mode 37 Ring Mode _______ 38 First Digit Time out Process Type Port reiease me un 39 Extension CPC Si
126. escription Function If enabled the system sends a dial tone to the extension user who seizes an El digital trunk line Available for E1 digital trunk lines only Notes In some countries the El card must not be connected to the Public Switched Network e Incase of the El digital trunk line the Central Office does not send a dial tone to the caller Reference e 1 3 System Features F G EI Carrier Group 109 3 2 Trunk Group Parameter PBX Ringback Tone Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether or not the system sends a ringback tone to the extension user who seizes an El digital trunk line Available for E1 digital trunk lines only Notes In some countries the El card must not be connected to the Public Switched Network e Incase of the El digital trunk line the Central Office does not send a ringback tone to the caller Reference e 1 3 System Features F G E1 Carrier Parameter Cyclic Signal Detection Default Check Value Range 1 No check Disable 2 Check Enable Description Function Used to disconnect the trunk line if the system detects a cyclic signal during a CO to CO line call by DISA Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter Continuous Signal Detection Default Check Value Range 1 No check Disable 2 Check Enable Description Function Used to disconnect the trunk line if the sy
127. estination Day Night Blank Name Blank MSN Line No Blank 9 2 2 Automatic Registration of DDI DID MSN Numbers Program Default Base Number Dial Blank Additional Number Number of Registrations 10 entries Additional Number Number of Digits 2 digits 00 99 Beginning Entry No 1 Entry No 1 10 Maintenance 10 1 Maintenance 10 2 External Modem 1 2 Program Default Manual Initialization Command 1 5 All Blank Automatic Initialization Command AT amp FOQOEOV 1S0 1X0 amp DO 10 3 External Modem 2 2 Program Default Connection Message 1 5 Message 1 CONNECT Others Blank Default Values 309 Program Default Disconnection Message 1 5 Message 1 NO CARRIER Others Blank 10 4 SMDR Program Default SMDR Connection No Output Type Type A Print out Error Information Disable Format Page Length 24 lines Format Skip Perforation 0 Duration Log Outgoing Calls All Duration Log Incoming Calls On Priority of Caller ID information Number Print out DDI DID subscriber number Disable Print out Incoming Call Start RC and Incoming Disable Call Answer AN information Print out No Answer of Timed Reminder Disable information Print out Account Code Enable Print out LOGIN LOGOUT Disable Print out Absent Message 6 9 Dis
128. ex system This is useful when the host PBX offers for example Call Waiting call Reference 2 8 2 If a Host PBX is Connected U M Parameter 39 Station Program Clear Default 790 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for Station Programme Clear Reference e 2 7 14 Clearing the Feature Settings at Your Extension Station Programme Clear U M Parameter 40 Message Waiting Set Cancel Call Back Default 70 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for setting cancelling the Message Waiting indications This is also used to call back the party who left a Message Waiting indication Reference e 2 2 4 When the Dialled Line is Busy or There is No Answer U M Parameter 41 OGM Playback Record Default 36 SP NL JT 712 G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for recording playing back an OGM Outgoing Message For Manager Operator only Reference e 3 2 2 Recording Outgoing Messages U M 47 2 3 Numbering Plan Parameter 42 Call FWD Do Not Disturb Set Cancel Default Value Range Description Function Reference 710 1 4 digits consisting of 0 9 X or Specifies the feature number for setting cancelling the Call Forwarding Do Not Disturb feature e 2 5 1 Forwarding Your Calls Call Forward
129. f 0 9 X or Description Function Specifies the feature number for cancelling Automatic Callback Busy feature Reference e 2 2 4 When the Dialled Line is Busy or There is No Answer U M Parameter 60 Walking COS Default 47 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for setting cancelling Walking COS feature Reference e 2 2 5 Calling without Restrictions U M Parameter 61 MODEM Control Default 791 SP NL JT Blank G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for External Modem Control An external modem can be connected to RS 232C port 1 Reference e 2 11 1 Controlling the External Modem External Modem Control U M 52 System 2 3 Numbering Plan Parameter 62 MCID Default 737 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for turning on off the MCID Malicious Call Identification feature Reference e 2 7 15 Identifying Malicious Callers Malicious Call Identification MCID U M Parameter 63 70 Quick dial 1 Quick dial 8 Default Blank Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for Quick Dial features Reference 2 2 2 Easy Dialling U M Parameter 71 Reserved Reserved for future use Default Blank Value Range Description Function
130. f UCD Calls Waiting to be Answered UCD Monitor Mode U M Parameter 76 TIE Line Access Default 77 SP NL JT Blank G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for making a TIE line call Reference 3 1 E amp M Features F G E amp M TIE Line Service 54 System 2 3 Numbering Plan Parameter 77 92 Other PBX 01 Other PBX 16 Default Blank Value Range 1 2 digits consisting of 0 9 Description Function Specifies the leading 1 or 2 digits of the other PBX extension numbers If you employ PBX code method for TIE calls this programming is not required Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter 93 Paging Deny Set Cancel Default 721 Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for setting cancelling Paging Deny feature Reference e 2 7 4 Denying the Paged Announcement Paging Deny U M Parameter 94 Trunk Busy out Default 726 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for Trunk Busy out feature For Manager Operator only Reference 3 2 3 Trunk Busy out Setting U M Parameter 95 Walking Station Default 727 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for Walking Station feature Reference e 2 9 1 U
131. f enabled the system disconnects the line with the time set in programme CPC Signal OUT Detection Detection Time when the CPC signal is detected Note e n some countries the El and the ELCOT cards must not be connected to the Public Switched Network Reference e 1 3 System Features F G Calling Party Control CPC Signal Detection 139 4 2 Trunk Line Parameter CPC Signal OUT Detection Detection Time ELCOT card Default 32ms SP None NL JT G Value Range 1 None 2 6 5 ms 3 2 75 x 8 ms Description Function Specifies the expected minimum duration for detecting CPC Calling Party Control signal on outgoing CO calls Note e In some countries the ELCOT card must not be connected to the Public Switched Network Reference e 1 3 System Features F G Calling Party Control CPC Signal Detection Parameter CPC Signal OUT Detection Detection Time E1 DR2 card Default 160 ms Value Range 1 None 2 1 15 x 80 ms Description Function Specifies the expected minimum duration for detecting CPC Calling Party Control signal on outgoing CO calls Note e In some countries the El card must not be connected to the Public Switched Network Reference e 1 3 System Features F G Calling Party Control CPC Signal Detection 140 Line 4 2 Trunk Line Parameter CPC Signal IN Detection Default Enable E1 DR2 ELCOT card SP Disable ELCOT card
132. f or all settings of a certain Trunk Line to all other same type Trunk Lines at a time You can also specify one or several Trunk Lines as the copy destination This copy function is available between the Trunk Lines of the same type Trunk Cards Copying the Trunk Line Parameters to Other Trunk Lines 1 Edit the parameters of the copy source Trunk Line and save it 2 Point to the Copy button on 4 1 Trunk Line screen of the copy source and click e Trunk Line Copy screen is displayed e The current Trunk Line copy source number is shown as Copy from XXX XXXXX XX Line 133 4 2 Trunk Line Copy from 101 ELCOT 01 r Copy Item Destination Trunk Line Card Port M e 101 ELCOT 02 IV Destination Day 401 ELCOT 03 IV Destination Night 101 ELCOT 04 F Start Signal Type 101 ELCOT 05 I CPC Signal OUTAN 101 ELCOT 06 101 ELCOT 07 IV Reverse Signal Detection 401 ELCOT 08 F Digits to receive DDIDID TE Wink Signal Time out F DDIDID TIE Digits to delete F ODIDID TIE Humber to be added F TiELine Type F TIELine SensitivitytH F TIELine Sensitivity OvT F TELine TIE10 C0 Security Mode F TIEl ne Sending NE Galler ID FF Collect Call Seas IV Answer Wait Timer ae F Subscriber 7 Dial Tone Detection Execute Cancel Help 3 Select the Trunk Line parameters to copy in Copy Item field e Only parameters which are available to copy are shown in Copy I
133. fies the 3 digit password for LCS settings Reference e 1 9 Answering Features F G Live Call Screening LCS e 2 8 3 If a Voice Processing System is Connected U M Line 4 3 Extension Line Parameter Call Log Incoming Overwrite Mode Default Yes Value Range 1 Yes 2 No Description Function Enables or disables Call Log Incoming Overwrite Mode If the Call Log is full 30 call records are already logged when a new Caller ID call comes in 1 Yes The new call record overwrites the oldest one in the Call Log 2 No The new call record is not logged Reference e 2 10 1 Calling Using the Call Log Incoming Call Log KX T7533 KX T7536 KX T7230 KX T7235 only U M Parameter Call Log Incoming Lock Password Default Blank Value Range Fixed to 3 digits consisting of 0 9 Description Function Specifies the Call Log Incoming Log Lock password The extension user can lock the call log display so that incoming call information is not shown on the display Note e The Manager and the Operators can cancel the Call Log Lock in case the extension user forgets the lock code Reference e 2 10 3 Denying Other People the Possibility of Seeing Your Call Log Incoming Call Log Lock KX T7533 KX T7536 KX T7230 KX T7235 only U M Parameter Pickup Dialing Mode Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether Pickup Dialling feature is enabled or not Reference e 1 7 D
134. fies whether to restrict the duration of outside calls or not Notes e If set to Yes the system disconnects a CO call originated or answered by the programmed extension user when the time specified by Extension to CO Line Call Duration Time 1 64 min in Section 2 5 System Timer expires e This setting may apply to Outgoing CO call only or Both incoming and outgoing CO calls depending on 5 Limited call duration setting in Section 2 8 System Option Reference None Parameter Transfer to CO Default Disable SP NL JT Enable G Value Range 1 Enable 2 Disable Description Function Enables or disables Call Transfer to Trunk feature Reference e 2 4 3 Transferring a Call U M 59 2 4 Class of Service COS Parameter Call FWD to CO Default Disable Value Range 1 Enable 2 Disable Description Function Enables or disables Call Forwarding to Trunk feature Reference e 2 5 1 Forwarding Your Calls Call Forwarding U M Parameter Call FWD Follow me Default Enable Value Range 1 Enable 2 Disable Description Function Enables or disables Call Forwarding Follow Me feature Reference e 2 5 1 Forwarding Your Calls Call Forwarding U M Parameter Busy Override Default Disable Value Range 1 Enable 2 Disable Description Function Enables or disables Executive Busy Override feature Reference e 2 2 4 When the Dialled Line is Busy or There is No Answer U M Parameter Busy Overrid
135. for turning on off the CTI Computer Telephony Integration Dial Information feature Reference None 56 System 2 3 Numbering Plan Parameter 100 COS Primary Default 792 SP NL JT 79 G Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for setting the COS Primary Reference e 3 1 5 Changing Service Level of Extensions Switching COS U M Parameter 101 COS Secondary Default 793 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for setting the COS Secondary Reference e 3 1 5 Changing Service Level of Extensions Switching COS U M Parameter 102 Room Status Ready Default 763 SP NL JT 795 G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for changing the room status Reference e 3 2 6 Hotel Use Features Hotel Application KX T7536 KX T7235 only U M Parameter 103 120 Reserved Reserved for future use Default Blank Value Range Description Function Reference 57 2 4 Class of Service COS 2 4 Class of Service COS Used to assign the Class of Service COS parameters 2 3 Class of Service Be cosno Mr Trunk Group Setting TRS Level Account Code Mode r Switching DayMight Mode Day Night
136. g DTMF signal Follow on ID Default 1 5s Value Range 1 0 55 2 1 08 3 1 5s 4 2 0s Description Function Specifies the length of time in seconds the system is to wait after VPS answers a call before sending DTMF signals such as a mailbox number Follow on ID to VPS Reference 1 3 System Features F G Integration VPS 202 Features 5 10 VPS Integration Parameter Pause timing before sending DTMF signal RBT BT Default 15s Value Range 1 0 5s 2 1 0s 3 1 5s 4 2 0 s Description Function Specifies the length of time in seconds the system is to wait before sending Integration Code with DTMF signals System Voice Mail Extension Status Reference e 1 3 System Features F G Integration VPS Parameter Turn off control of Message Waiting lamp Default System Value Range 1 System 2 Voice Mail Description Function Specifies whether the system or the VPS turns off the Message Waiting lamp after the extension user retrieved a message recorded in his her mailbox Reference e 1 3 System Features F G Integration VPS e 1 17 Display Features F G Message Waiting Parameter Start AA service after FWD IRNA of CO call Default Do not start Value Range 1 Do not start 2 Start Description Function Specifies whether the system starts the AA Automated Attendant Service or not if a CO call is directed to VPS by Call Forwarding or Intercept Routing If Start is specified AA Service
137. gnal 40 TSW Tone Selection 41 Fixed Feature Number 42 DPT Ringer OFF 43 LCD Time Display Mode 44 Hotel Application Enable Disable 12h C 24h C Enable Disable 4 Flash Signal before CO Disconnect 47 Tone Type for Outgoing Calls Date Display C Enable Disable MDY Busy Reorder 48 Call Pickup with DSS S CO key 49 LCD Display Mode while CO talking Enable Disable Caller ID C Duration Parameter 31 Answering Call Waiting call by SLT hooking Default Disable Value Range 1 Enable 2 Disable Description Function If enabled an SLT user can answer a call waiting call simply by flashing the switchhook Reference e 1 9 Answering Features F G Call Waiting Parameter 32 Whisper OHCA to extensions other than T74 75XX Default Disable Value Range 1 Enable 2 Disable Description Function If enabled an extension user can make a Whisper OHCA call to extensions other than KX T7500 series PT Reference e 1 6 Originating Features F G Off Hook Call Announcement OHCA Whisper e 2 7 3 Receiving a Call Waiting Call Waiting Off Hook Call Announcement OHCA Whisper OHCA U M System 2 8 System Option Parameter 33 FWD DND lamp pattern Default FWD Flash DND On Value Range 1 FWD Flash DND On 2 FWD On DND Flash Description Function Specifies the lamp patterns of the FWD DND button Referenc
138. hange the status of the SLT port because the PT port is activated as a Parallel Mode extension Please change the PT port status to XDP Mode and then press Apply E1038 You have exceeded the shelf limit of extension ports There is a limit of 192 extension ports per shelf when using DLC DHLC and ESLC cards Please de assign one card and try again E1039 You have exceeded the shelf limit of SLT ports There is a limit of 160 SLT ports per shelf when using DHLC and ESLC cards Please de assign one card and try again Programming Error Messages 273 11 1 Error Messages EXXXX Error Message Error Code Description E1050 The slot next to PRI card must be empty Please remove and re assign the card that is installed next to a PRI card A PRI card must go into slot no 1 3 5 7 9 11 or 13 E1051 E1 card should be assigned to the slot no 1 5 or 9 El card should be assigned to the slot no 1 5 or 9 of basic shelf expansion shelf 1 and expansion shelf 2 E1052 The slot next to E1 card must be empty Please remove and re assign the card that is installed next to an El card An El card must go into slot no 1 5 or 9 E1053 PRI card must be assigned to an odd numbered slot PRI card should be assigned to the odd numbered slot of basic shelf expansion shelf 1 and expansion shelf 2 E1054 The status of the card must be OUS Out of Service When you change the card properties of
139. he decimal point format Reference e 4 2 Charge Fee Management Station Programming U M Parameter Currency Default SP NL JT DM G Value Range Up to 2 characters consisting of 0 9 A Z a z or the following marks x lt gt amp Description Function Specifies the currency appropriate to your country Reference None Features 5 14 Charge Parameter Currency Display Position Default Tail Value Range 1 Head 2 Tail Description Function Specifies whether the currency of the charge is displayed before Head or after Tail the charge display Reference None Parameter Treatment of Charge Limit Default Alarm Tone Value Range 1 Alarm Tone 2 Alarm Tone and Disconnect 3 Disconnect Description Function Specifies the treatment of the call caller when the telephone charge of the extension exceeds the pre assigned limit during a call Reference None Parameter Meter Count up by Answer Detection Default Disable Value Range 1 Enable 2 Disable Description Function Specifies whether or not the system starts the counting of telephone charge when the system detects the answer signal from the Central Office Reference None 215 Hotel Used to assign parameters for Hotel Application 5 15 Hotel Be Title Header 3 lines 10 20 30 40 50 60 70 80 4444424444444 4444 ER A A A A A A a A a a r Check Out Sheet K
140. he default values per Card Type gt Card Type Selection Default BRI TIE DDI MSN DDI El DIL DID TIE DID TIE Refer to the ee below E amp M DIL TIE TIE ELCOT DIL DIL PRI30 TIE DDI DDI lt Default values for E1 card per Channel Type Receiver Type gt Channel Type Receiver Type Default DR2 Pulse DTMF MFC R2 DID E amp M C MFC R2 E amp M P Pul ulse DTMF DIE Notes In some cases the default cannot be changed e In some countries the El the E amp M and the ELCOT cards must not be connected to the Public Switched Network Line 137 4 2 Trunk Line Parameter Incoming Type Reference e 1 5 Attended Features F G Direct In Lines DIL Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDI 3 1 E amp M Features F G E amp M TIE Line Service Parameter Dial Type Default Value Range Description Function Reference DTMF 80 E1 E amp M ELCOT card SP NL JT Pulse 10 E1 E amp M ELCOT card G ISDN BRI PRI30 card Pulse 10 10 PPS Pulse 20 20 PPS DTMF 80 80 ms DTMF 160 160 ms MFC R2 ISDN An RWNe Specifies the dial type for each trunk line This is the dial type regardless of the dial mode of the extension telephone The dialling signals from any extension are converted to the dial type specified by this setting and trans
141. ialling Features F G Pickup Dialling Hot Line e 2 2 2 Easy Dialling U M Line 155 4 3 Extension Line Parameter Pickup Dialing Dial Default Display only Value Range Up to 24 digits Description Function Displays the telephone number for Pickup Dialling feature The system automatically dials this number when an extension user goes off hook to make a call if Pickup Dialling is enabled Reference 1 7 Dialling Features F G Pickup Dialling Hot Line e 2 2 2 Easy Dialling U M Parameter Data Line Mode Default No Value Range 1 Yes 2 No Description Function Assigns whether Data Line Security mode is available or not If set to No setting Data Line Security mode by dialling the feature number is impossible Reference e 1 12 Conversation Features F G Data Line Security e 2 7 11 Protecting Your Line against Indication Tones Data Line Security U M Parameter Call Waiting Tone Type Default Tone 1 Value Range 1 Tone 1 2 Tone 2 Description Function Specifies the type of Call Waiting Tone for PT extensions Please refer to Section 5 4 What is This Tone in the User Manual for detailed information on Tone Type Reference e 2 4 4 Answering a Call Waiting U M e 4 1 1 Initial Settings U M Line 4 3 Extension Line Parameter Call Pickup Deny Default Disable Value Range 1 Enable 2 Disable Description Function Enables or disables Call Pi
142. ic on Hold is not provided by the system Reference e 1 11 Transferring Features F G Call Transfer e 2 4 3 Transferring a Call U M 78 System 2 8 System Option Parameter 2 SLT On hook with consulting held call Default Consulting Hold Value Range 1 Consulting Hold 2 Disconnect Description Function Specifies the result of pressing the switchhook lightly and then replacing the handset during an outside call This setting applies to SLT users only Reference e 1 10 Holding Features F G Consultation Hold Parameter 3 FLASH button operation while CO talking Default Don t release the trunk SP NL Release the trunk JT G Value Range 1 Release the trunk 2 Don t release the trunk Description Function Specifies the result of pressing the FLASH button on PT during an outside call Reference e 1 12 Conversation Features F G External Feature Access Parameter 4 FLASH button operation when Don t release the trunk is selected at 3 Default Sending EFA signal SP NL Disconnect and hear CO dial tone JT G Value Range 1 Disconnect and hear CO dial tone 2 Sending EFA signal Description Function Specifies the result of pressing the FLASH button on PT during an outside call when Don t release the trunk is selected in 3 FLASH button operation while CO talking Reference e 1 12 Conversation Features F G External Feature Access 79 2 8 System Option
143. ied in 2 1 Tenant screen 5 1 System Speed Dialing Tenant Ho Entry No A M 000 019 M Max Entry 1000 Current Registration 0 Entries Ho Hame Humber Max 10 Characters Max 24 Digits 000 010 001 011 of N og 003 nf 013 004 014 005 015 of S o oe 007 017 008 018 of S S og 5 1 System Speed Dialing M oK Apply Cancel Help Parameter Tenant No Default 1 Value Range 1 8 Description Function Specifies the tenant to which the System Speed Dialling codes are assigned Required when Tenant Service is employed Reference 1 3 System Features F G Tenant Service 2 2 Tenant P G Parameter Entry No Default 000 019 Value Range 000 999 in 20 codes increments Description Function Specifies the entry number of the Speed Dialling codes which you are going to programme Reference None Features 185 5 2 System Speed Dialling Parameter Max Entry Default Display only Value Range 0 1000 Description Function Displays the maximum number of Speed Dialling codes allocated to the tenant Reference None Parameter Current Registration Default Display only Value Range 0 1000 Description Function Displays the total number of Speed Dialling codes which are already programmed Reference None Parameter Name Default Blank Value Range Up to 10 characters consisting of 0 9 A Z a z or the
144. ign one card and try again E1005 You have exceeded the system limit of DISA cards There is a limit of 8 DISA cards per system Programming Error Messages 271 11 1 Error Messages EXXXX Error Message Error Code Description E1007 You have exceeded the system limit of remote cards One ERMT card can be installed in the system only one E1008 You have exceeded the system limit of DPH cards There is a limit of two DPH cards per system E1010 You must change card type to None before changing to new card type This process to make sure all data for previous card is deleted E1011 The card of clock configuration priority duplicated Each card must have a unique priority E1012 The status of the card is not INS In Service To use this port you must put the card INS In Service When the card is INS In Service status all the ports of the card become in service E1013 Cannot change the attribute of the port which is the paired extension of a DSS console The attribute of this port cannot be changed until it is de assigned as the paired extension of a DSS console Please change the attribute after de assignment E1014 You have exceeded the system limit of DSS consoles There is a limit of 64 consoles per system E1015 Incomplete directory number The DN and FDN must be 3 or 4 digits E1016 Invalid directory number The entered DN doesn t match the numbering pla
145. ination Day Night Blank Line Hunting Order Normal Disconnecting Time 1 5 s SP NL JT 2 0 s G Pause Time 1 5 s SP NL 3 5 s JT G Pause Time before Flash Signal 512 ms Flash Time 80 ms SP NL JT 300 ms G Max Dial No after EFA Signal 0 PBX Access Code Blank PBX Dial Tone Disable PBX Ringback Tone Disable Cyclic Signal Detection Check Continuous Signal Detection Check Silence Detection Check Numbering Plan ID Outgoing Public Default Numbering Plan ID Outgoing Private Default Numbering Plan ID Incoming Public Default Numbering Plan ID Incoming Private Default Type of Number Outgoing Public Default Type of Number Outgoing Private Default Type of Number Incoming Public Default Type of Number Incoming Private Default 296 Default Values 3 3 Extension Group 3 3 1 Extension Group Copy Program Default Group No 1 FDN Blank Group Type Group No 126 VM Group No 127 AA Group No 128 Operator Others None Tenant No 1 Overflow Setting Destination Day Night Blank Overflow Setting Timer None FWD DND Mode Enable Extension Call Hunting Enable Operator Setting Ringing Type Single Operator Setting Call Priority CO Call 1 Intercept Routing 2 Recall 3 Extension Call 4 UCD Setting
146. ing U M e 2 7 2 Refusing Incoming Calls Do Not Disturb DND U M Parameter 43 Dial Call Pickup Deny Set Cancel Default Value Range Description Function Reference 720 1 4 digits consisting of 0 9 X or Specifies the feature number for setting cancelling the Dial Call Pickup deny feature e 2 7 8 Denying Other People the Possibility of Picking up Your Calls Call Pickup Deny U M Parameter 44 Data Line Security Set Cancel Default Value Range Description Function Reference 730 1 4 digits consisting of 0 9 or Specifies the feature number for setting cancelling the Data Line Security feature e 2 7 11 Protecting Your Line against Indication Tones Data Line Security U M Parameter 45 Call Waiting Set Cancel Default Value Range Description Function Reference 731 1 4 digits consisting of 0 9 X or Specifies the feature number for setting cancelling Call Waiting feature e 2 7 3 Receiving a Call Waiting Call Waiting Off Hook Call Announcement OHCA Whisper OHCA U M 48 System 2 3 Numbering Plan Parameter 46 Executive Busy Override Deny Set Cancel Default 733 Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for setting cancelling Executive Busy Override Deny feature Reference e 2 7 9 Denying Other People the Possibility of Joining
147. ing Entry No must be equal to or less than 991 The total digits of Base Number and Number of Digits are over 16 Programming Error Messages 279 11 2 Warning Messages WXXXX 11 2 Warning Messages WXXXX Message Code Description W0001 Save system data Some parameters on the screen were changed A click on OK or a screen switch was attempted without saving data W0002 The status of the port is In Service INS Would you like to continue When the status of a port is In Service INS and you change some parameters screens of 1 Configuration the port is reset A call in progress will be dropped W0003 Save system data before Copy Modified parameters without saving are not effective for Copy feature W0005 Save data file Tried to close exit or open another file without saving data in the Batch mode although parameters were changed W1001 Change the card XXX YYY status Please confirm whether or not to execute OUS Out of Service INS In Service command to the card XXX YYY XXX Slot No YYY Card Type The OUS Out of Service INS In Service command to the card is effective to the whole ports of the card W1002 Change the status of port XXXXX Please confirm whether or not to execute OUS Out of Service INS In Service command to the port XXXXX XXXXX port physical number W2001 Would you like to upload a language data Specifies whe
148. ion 727 96 CLIP COLP 711 97 CLIR 59 SP NL JT 57 G 98 COLR 58 99 Dial Information CTT Blank 100 COS Primary 792 SP NL JT 79 G 101 COS Secondary 793 102 Room Status Ready 763 SP NL JT 795 G 103 120 Reserved Reserved for future use Blank 2 4 Class of Service COS Program Default COS No 1 Trunk Group Setting Please refer to Section 2 4 1 Trunk Group Setting TRS Level Day Night 1 Time Limit of Outside Calls No Transfer to CO Disable SP NL JT Enable G Call FWD to CO Disable Call FWD Follow me Enable Busy Override Disable Busy Override Deny Enable DND Override Disable Digits Restriction in CO Talk Mode Unrestricted Call from TRS Level 7 Extension Enable Default Values 291 Program Default Switching Day Night Mode Disable SP NL JT Enable G Account Code Mode Optional SDN COS Own Extension Off Hook Call Announcement OHCA Enable Released Link Operation Disable Automatic Hold Disable Charge Management Disable ISDN CFU CFB CFNR Disable 2 4 1 Trunk Group Setting Program Default Trunk Group No 01 48 Day Night All Check 2 5 System Timer 2 5 1 System Timer 1 2 Program Default Hold Recall Time 60 s Transfer Recall Time 12 rings Pickup Dial Waiting Time ls Call Duration Cou
149. ion Function Specifies the CO button number to which the extension is connected when it goes off hook to answer a call This assignment is required when Prime Line CO is specified in Preferred Line Incoming programming Reference e 4 1 1 Initial Settings U M Parameter LCS Setting Status Default Inactive Value Range 1 Inactive 2 Active Description Function Specifies whether or not the extension can use the LCS Live Call Screening feature Reference e 1 9 Answering Features F G Live Call Screening LCS 153 4 3 Extension Line Parameter LCS Setting Operation Mode Default Hands free Value Range 1 Private 2 Hands free Description Function Assigns whether the voice message being recorded is monitored automatically through the built in speaker Hands free mode or an alert tone is sent Private mode while an incoming caller is leaving a message in the mailbox of the extension Reference e 1 9 Answering Features F G Live Call Screening LCS e 4 1 1 Initial Settings U M Parameter LCS Setting Recording Mode Default Stop Rec Value Range 1 Keep Rec 2 Stop Rec Description Function Assigns whether to close the mailbox or keep recording the conversation after a call is interrupted Reference e 1 9 Answering Features F G Live Call Screening LCS Parameter LCS Setting LCS Password Default Blank Value Range Fixed to 3 digits consisting of 0 9 Description Function Speci
150. ion Function Specifies the feature number for retrieving a specific outside call held at another extension Reference e 2 4 1 Holding a Call U M Parameter 34 Redial Default Value Range 1 4 digits consisting of 0 9 x or Description Function Specifies the feature number for dialling the last number dialled Reference e 2 2 3 Redial U M Parameter 35 Call Park Call Park Retrieve Default 52 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for placing a call on hold retrieving the call held in the system common parking area Reference e 2 4 1 Holding a Call U M Parameter 36 Account Code Default 49 Value Range 1 4 digits consisting of 0 9 x or Description Function Specifies the feature number for entering account codes which may be forced or optional depending on Class of Service programming Reference e 2 2 5 Calling without Restrictions U M Parameter 37 Door Open Default 55 Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for unlocking the Door Opener Reference e 2 8 1 If a Doorphone Door Opener is Connected U M 46 System 2 3 Numbering Plan Parameter 38 External Feature Access Default 6 SP NL JT 66 G Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number for sending a switchhook flash to a host PBX or Centr
151. ion Specifies Disconnection Message from Modem marks x lt gt amp Reference 1 3 System Features F G External Modem Control e 2 11 1 Controlling the External Modem External Modem Control U M Maintenance 10 4 SMDR 10 4 SMDR Station Message Detail Recording SMDR automatically records detailed information for outside calls Parameter SMDR Connection Default No Value Range 1 Yes 2 No Description Function Enables or disables SMDR Reference e 2 8 4 Personal Computer Printer I M 252 Maintenance 10 4 SMDR Parameter Output Type Default Type A Value Range 1 Type A 2 Type B 3 Type C 4 Type D Description Function Specifies the output type of SMDR information For further information please refer to Station Message Detail Recording SMDR in Section 1 3 System Features of the Features Guide You can also get information on Output Type by clicking Help button on this screen Reference e 1 3 System Features F G Station Message Detail Recording SMDR Parameter Print out Error Information Default Disable Value Range 1 Disable 2 Enable Description Function Specifies whether or not the Error Information will be printed out by SMDR Reference 5 2 3 Troubleshooting via Error Log Records I M Parameter Format Page Length Default 24 lines Value Range 4 99 lines Description Function Specifies th
152. isplay Mode while CO talking Default Caller ID Value Range 1 Caller ID 2 Duration Description Function Specifies the initial display Caller ID or Call Duration which is shown on the display while CO talking Reference e 1 5 Attended Features F G Caller ID Service System 97 2 9 Language Data 2 9 Language Data Display Language The KX TD500 System provides two different languages as the Display Language at the same time which is shown on the display of a Panasonic Proprietary Telephone PT Each PT user can choose English default or Optional Language so PTs on the same KX TD500 System can display different languages Optional Language One of the following four Optional Languages is available with the KX TD500 System French Dutch Spanish or Portuguese French is stored as the default Optional Language at the factory Language Data File If you want to use the Optional Language other than French please upload the appropriate Language Data File distributed with the PC System Programming Installation media lt Uploading the Language Data to the KX TD500 System gt 1 Start up the System in on line mode 2 Connect the PC System Programming device Windows PC to the KX TD500 System and go into the Interactive mode 3 Point to 2 8 Language Data from the Programming 2 System drop down menu and click e The Language Data Selection dialogue box is displayed 4 Select the appropriate Lang
153. ists and it is damaged you will get this error message You must either repair the damage using a text editor or rename it as a different file E0016 Failed Deletion of remote connection parameters Deletion of remote connection parameters failed because file TD500 INI is damaged Please refer to the description of E0015 E0017 Failed Reading of remote connection parameters Reading of remote connection parameters failed because file TD500 INI is damaged Please refer to the description of E0015 E0018 There is not enough space on your hard disk or floppy to save the system data Download is incomplete because there is not enough space on your hard disk or floppy to save the system data E1001 You have exceeded the shelf limit of PT ports There is a limit of 128 PT ports per shelf when using DLC and DHLC cards Please de assign one card and try again E1002 You have exceeded the system limit of trunk ports There is a limit of 192 trunk ports per system when using ELCOT E1 E amp M BRI and PRI30 cards Please de assign one card and try again E1003 You have exceeded the system limit of extension ports There is a limit of 448 extension ports per system when using DLC DHLC and ESLC cards Please de assign one card and try again E1004 You have exceeded the system limit of trunk extension ports There is a limit of 512 trunk extension ports per system using trunk and extension cards Please de ass
154. leading 3 digits are saved and the rest are deleted W8002 TIE Leading dial must not exceed 3 digits Truncate it Truncate means that the leading 3 digits are saved and the rest are deleted W8003 TIE additional dial must not exceed 20 digits Truncate it Truncate means that the leading 20 digits are saved and the rest are deleted w9001 DDI DID dial must not exceed 16 digits Truncate it Truncate means that the leading 16 digits are saved and the rest are deleted W9002 DDI DID name must not exceed 10 characters Truncate it Truncate means that the leading 10 characters are saved and the rest are deleted W9003 Modem command must not exceed 80 characters Truncate it Truncate means that the leading 80 characters are saved and the rest are deleted W9004 Modem messages must not exceed 80 characters Truncate it Truncate means that the leading 80 characters are saved and the rest are deleted W9005 Base dial number must not exceed 15 digits Truncate it Truncate means that the leading 15 digits are saved and the rest are deleted 282 Programming Error Messages 11 3 Information Message IXXXX 11 3 Information Message IXXXX Message Code Description 10001 Upload completed Please change PBX to on line mode Uploading the system programming data from PC to PBX is completed How to change PBX to on line mode 1 Set CPU Mode Rotary Switch position to 0 2
155. lking Hold 294 Default Values Program Default 27 Message Waiting lamp pattern 11 28 Trunk hunting mode Forced 30 Net CODEC A law 2 8 4 System Option 4 4 Program Default 31 Answering Call Waiting call by SLT hooking Disable 32 Whisper OHCA to extensions other than T74 Disable T5XX 33 FWD DND lamp pattern FWD Flash DND On 34 ELCOT LCOT Busy out Loop Relay OFF 36 Tone Mode Type 1 SP NL G Type 7 JT 37 Ring Mode Type 6 SP Type 1 NL G Type S JT 38 First Digit Time out Process Don t release the trunk 39 Extension CPC Signal 48 ms SP None NL JT G 40 TSW Tone Selection TONE A 41 Fixed Feature Number Type 2 42 DPT Ringer OFF Enable SP NL G Disable JT 43 LCD Time Display Mode 12 h SP 24 h NL JT G 44 Hotel Application Disable 45 Flash Signal before CO Disconnect Disable 46 Date Display D M Y SP NL JT M D Y G 47 Tone Type for Outgoing Calls Busy Reorder 48 Call Pickup with DSS S CO key Disable 49 LCD Display Mode while CO talking Caller ID Default Values 295 2 9 Language Data 3 Group 3 1 Group 32 Trunk Group 3 2 1 Trunk Group Copy Program Default Group No 1 Type Public Tenant No 1 Intercept Dest
156. long operation setting in Section 2 8 System Option the call duration can be prolonged 10 times or without limit Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter DISA Delayed Answer Time Default 1 ring Value Range 0 6 rings Description Function Specifies the number of rings the system is to wait after receiving a DISA call before answering it Note e A DISA call is answered after a ringback tone is returned to the caller after the DISA Delayed Answer Time expires The DISA caller can dial while hearing the OGM message Reference e 1 5 Attended Features F G Direct Inward System Access DISA 73 2 5 System Timer Parameter Timed Reminder Arrive Count Default 3 times Value Range 1 5 times Description Function Specifies the number of times 1 5 Timed Reminder Remote Timed Reminder Wake Up Call is repeated until the destination extension answers it Reference e 1 8 Ringing Features F G Timed Reminder Wake Up Call Timed Reminder Remote Wake Up Call e 2 7 1 Setting the Alarm Timed Reminder Wake Up Call U M e 3 1 1 Setting the Alarm for Other Extensions Remote Timed Reminder Wake Up Call U M Parameter DISA Automated Attendant Time Default ls Value Range 1 5 s Description Function Specifies the length of time in seconds the system is to wait before recognising the first digit as a DISA Automated Attendant number If this timer
157. m Extensi n sossen riein ennan annesin naana EA aana arana AELA Nia n teren 187 Emergency Dial Code eoessscoesssoocsssocsssooscscoesssoosssooesssossssocosesoossssosessoosssocssssoosssoosse 188 QUICK DIAG s vsccssssessssnncesoes snuscsconessvenssbuccsssasdeneseovasessetsieteobesssedessneesesueessedesescssesasvens 189 Account COE sisina aa aiea Aar A E REEE AEN A EEE 190 Table of Contents 3 5 7 Sp cial Carrier COG sicccseccccsestssosssessvsocncssaceesesteevecssctacscanssussesseurecsadsvsusssevedseavastsnessees 192 5 8 Absent MESSAGE wa cccccsscsesccesenscossacsccsseesecsSeossesseestccdvestsccesesdscasustesesessscssuseusesusseccersesscesss 193 5 9 DISA TIE User CO 6 ccciccssacsccccssicicovsiccevecesescsetcestesesdecesosccssanaccuenseesesdectcseseedsetevenet 195 510 VPS IME SLALION ss ccsssceessisesosetbscoscassvonsenssessessousscessasseenseunetebosssnsessncestonseseccesesesesesstsves 197 5 11 Caller ID Modification cc cccesseccccccssscceessscesceccescesstiescsceccerscsestercsocscerscstessncscesersseseas 206 5 12 Caller ID Registration oesesooeessoocssssocsssocccssoossssooesssocessocossssoossssoosssocossssoosessoosese 209 5 13 UCD Time Tale iin cccissecciccisssscccccssscccuvecchsveacteccensesseeaesdscevesccesaacesstecssestensccsstaestecevenss 211 5 14 Charge sicietivictsisccssetecisseasevencectacsesssenstoonscessunseudsestevissoseesencestensvuncesvecsabesebectsssesevesess tes 213 5 15 HOE ssisissessscscsssscesso
158. mber of Registrations is 20 and Beginning Entry No is 991 10 of 1000 Entry fields are left only the first 10 DDI DID MSN numbers are registered Parameter Base Number Dial Default Blank Value Range Up to 15 digits consisting of 0 9 Description Function Specifies the base number for automatic registration Additional numbers are appended to the end of this number Reference Parameter Additional Number Number of Registrations Default 10 entries Value Range 10 100 entries in 10 entries increments Description Function Specifies the number of DDI DID MSN entries to be registered automatically Reference 244 DDI DID 9 2 Number Transformation Parameter Additional Number Number of Digits Default 2 digits 00 99 Value Range 1 16 digits in 1 digit increment Description Function Specifies the number of digits to be added to the end of the Base Number Reference Parameter Beginning Entry No Default 1 Entry No 1 Value Range 1 991 Description Function Specifies the first entry number for automatic registration This number corresponds to the DDI DID MSN Entry No on 9 1 Number Transformation screen Reference DDI DID 245 9 2 Number Transformation 246 DDI DID Section 10 Maintenance Maintenance 247 10 1 Maintenance 10 1 Maintenance Used to assign parameters for system maintenance fi TD500 Maintenance Conso
159. meters Required by Key Type gt Depending on a Key Type additional parameters are required as follows Additional Key Type Parameters Description default SINGLE CO Trunk Line No Specifies the trunk port physical number 10101 to 31416 Tone 2 Specifies the ringer frequency ring tone type 1 8 for incoming calls GROUP CO Trunk Group No Specifies the Trunk Group number 01 48 Tone 2 Specifies the ringer frequency ring tone type 1 8 for incoming calls LOOP CO Tone 2 Specifies the ringer frequency ring tone type 1 8 for incoming calls DSS EXT Specifies the extension number 3 or 4 digits PHANTOM EXT Specifies the phantom extension number 3 or 4 digits Ringing Yes Specifies whether the extension rings or not when a call toa phantom button comes in on the extension PDN Tone 2 Specifies the ringer frequency ring tone type 1 8 for incoming calls Ringing Type Specifies the timing of ringing when a call comes in on the Immediate extension Immediate 1 ring Delay 3 ring Delay 6 ring Delay No Ring SDN EXT Specifies the PDN owner s extension number 3 or 4 digits Tone 2 Specifies the ringer frequency ring tone type 1 8 for incoming calls Ringing Type Specifies the timing of ringing when a call comes in on the Immediate extension Immediate 1 ring Delay 3 ring Delay 6 ring Delay No Ring ONE TOUCH Dial Specifies the telephone numb
160. mitted to the trunk line lt Available selections and the default values per Card Type gt Card Type Selection Default BRI PRI30 ISDN ISDN E amp MI ELCOT Pulse 10 Pulse 20 DTMF 80 DTMF 80 DTMF 160 Pulse 10 2 El Pulse 10 Pulse 20 DTMF 80 DTMF 80 DTMF 160 Pulse 10 2 MFC R2 1 DTMF 80 SP NL JT 2 Pulse 10 G Notes e In some countries the El the E amp M and the ELCOT cards must not be connected to the Public Switched Network None 138 Line 4 2 Trunk Line Parameter Destination Day Night Default 1001 SP NL JT 2001 G Value Range 3 4 digits consisting of 0 9 Description Function Specifies the destination for the trunk line whose Incoming Type is set to DIL The following numbers can be assigned as the destination Extension numbers FDNs Assignable only when DIL is specified in Incoming Type programming Reference e 1 5 Attended Features F G Direct In Lines DIL Parameter Subscriber Default Blank Value Range Up to 16 digits consisting of 0 9 Description Function Specifies the number which is used as the CLIP COLP or ANI Automatic Number Indication number Reference None Parameter CPC Signal OUT Detection Default Disable ELCOT card Enable El DR2 card Value Range 1 Enable 2 Disable Description Function Specifies whether CPC Detection on outgoing CO calls is enabled or disabled I
161. mplifies the transfer operation by eliminating the need for going on hook or pressing the RELEASE button after transferring the call This feature is convenient for extension users such as Operators who handle a large volume of calls Reference e 1 3 System Features F G Released Link Operation e 2 4 3 Transferring a Call U M Parameter Automatic Hold Default Disable Value Range 1 Enable 2 Disable Description Function Used to turn on off Automatic Hold feature Reference e 1 10 Holding Features F G Automatic Hold All Calls Automatic Hold Trunk Parameter Charge Management Default Disable Value Range 1 Enable 2 Disable Description Function Enables or disables the ability of performing Charge Management feature Reference e 1 3 System Features F G Charge Fee Reference e 4 2 Charge Fee Management Station Programming U M System 2 4 Class of Service COS Parameter ISDN CFU CFB CFNR Default Disable Value Range 1 Enable 2 Disable Description Function Enables or disables the ability of performing Call Forwarding by ISDN Line CFU CFB CFNR feature Note CFU Call Forwarding Unconditional CFB Call Forwarding Busy CENR Call Forwarding No Reply Reference e 2 5 ISDN Transferring Features F G Call Forwarding by ISDN Line e 2 5 2 Forwarding Your Calls by ISDN Call Forwarding by ISDN Provider U M 2 4 1 Trunk Group Setting Used to specify the trunk gr
162. n Parameter 2 2nd Hundred Block Extension Default 11 SP NL JT 21 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering Parameter 3 3rd Hundred Block Extension Default 12 SP NL JT 22 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering Parameter 4 4th Hundred Block Extension Default 13 SP NL JT 23 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering Parameter 5 5th Hundred Block Extension Default 14 SP NL JT 24 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering Parameter 6 6th Hundred Block Extension Default 20 SP NL JT 30 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexible Numbering 40 System 2 3 Numbering Plan Parameter 7 7th Hundred Block Extension Default 21 SP NL JT 31 G Value Range 1 2 digits consisting of 0 9 Description Function Same as the Parameter 1 Reference e 1 3 System Features F G Flexibl
163. n and click e Are you sure is displayed 6 Point to Yes Y button and click e Copying is displayed while the source data is being copied to the destination e Parameters of the destination DSS Consoles are immediately effective when copying is finished Notes e Flexible DSS PF Key Assignment should be done before executing this copy function e Copy function is not available in the Interactive mode Parameter Paired Extension Default Value Range 3 4 digits consisting of 0 9 Description Function Specifies the extension number of the extension paired with the DSS console Reference e 1 15 Proprietary Telephone Features F G DSS Console Line 167 4 4 DSS Console Parameter DSS Console 1 8 Port No Default Display only Value Range Extension port physical number Description Function Displays the extension port to which the DSS console is connected Reference e 1 15 Proprietary Telephone Features F G DSS Console 1 4 Extension Port Assignment P G Parameter DSS Console 1 8 Model Default T7540 Value Range 1 T7540 2 T7541 3 Others Description Function Specifies the Model No of DSS console Reference e 1 15 Proprietary Telephone Features F G DSS Console Parameter DSS Key Default Not Stored Value Range Please refer to Section 4 4 2 Flexible DSS Key Assignment Description Function Used to determine the usage of the flexible DSS butto
164. n in 2 2 Numbering Plan screen E1017 Directory number already exists The entered DN or FDN already exists E1018 Directory number doesn t exist The entered DN doesn t exist E1019 Invalid directory number for paired extension of DSS console Only the DN of PT can be assigned as the DN for the paired extension of a DSS console E1020 You have exceeded the limit of DSS consoles per PT There is a limit of 8 DSS consoles per PT E1022 Assign the directory number before making the port INS In Service status An extension without a DN cannot be placed into service E1023 Assign the directory numbers for EXT 1 and EXT 2 For the VPS port you must assign directory numbers for both voice mail numbers EXT 1 and EXT 2 These cannot be assigned individually E1024 Cannot assign the port which does not have VPS DPT attribute To be used as a VPS port this port must have the VPS DPT attribute in 1 3 Extension Port Assignment screen 272 Programming Error Messages 11 1 Error Messages EXXXX Error Message Error Code Description E1025 Specify the extension group number The extension group number of VPS port should be always assigned E1026 Port number duplicated Please assign the port number of TVP uniquely E1028 Card type should be changed only in OUS Out of Service status Please make the card OUS Out of service status before deleting the card E1029
165. nder Wake Up Call Timed Reminder Remote Wake Up Call e 1 17 Display Features F G Display Date and Time e 4 3 1 Date and Time Set 000 U M 10 5 System Time eede ee ee ma System Time Parameter Year Default 00 Value Range 00 99 Description Function Specifies the last two digits of the year by entering the value directly Reference None Maintenance 265 10 7 System Time Parameter Month Default Jan Value Range Jan Dec Description Function Selects the month by clicking the small triangle Reference None Parameter Day Default 01 Value Range 01 31 Description Function Specifies the date in two digits by entering the value directly Reference None Parameter Day of the week Default Sat Value Range Sun Sat Description Function Selects the day of the week by clicking the small triangle Reference None Parameter Hour Default 12 Value Range 0 1 12 Description Function Specifies the hour in two digits by entering the value directly Reference None Parameter Minute Default 00 Value Range 00 59 Description Function Specifies the minute in two digits by entering the value directly Reference None 266 Maintenance 10 7 System Time Parameter AM PM Default AM Value Range AM PM Description Function Selects AM PM by clicking the small triangle Reference None Maintenance 267 10 7 System Time
166. ne 17 Hone x 5 Hone 17 Hone M 7 None x 19 Hone xl 7 Hone x 19 Hone M 9 Hone 21 Hone xl 9 Hone 21 None M 11 Hone x 23 Hone xl 11 Hone x 23 Hone x 12 Hone x 24 None x 12 None 24 None 10 3 Power Failure Transfer x _ ox Apply Cancel Help Parameter Trunk Card 1 24 Default None Value Range None XXX YYY XXX Card No 101 314 YYY Card Type Description Function Specifies the trunk card number and its type which will be used in case of Power Failure Transfer Reference e 1 4 Fault Recovery Diagnostics F G Power Failure Transfer e 2 9 1 Auxiliary Connection for Power Failure Transfer I M 1 2 Slot Assignment P G 258 Maintenance 10 5 Power Failure Transfer Parameter Extension Card 1 24 Default None Value Range None XXX YYY XXX Card No 101 314 YYY Card Type Description Function Specifies the extension card number and its type which will be used in case of Power Failure Transfer Notes e DPTs and some APTs cannot be used during a power failure e Auxiliary connections between the Trunk card and Extension card should be made as per the System Programming so that conversation is maintained when power is down or TSW is recovering Reference e 1 4 Fault Recovery Diagnostics F G Power Failure Transfer e 2 9 1 Auxiliary Connection for Power Failure Transfer I M 1 2 Slot Assignment P G Maintenance 259
167. new data will be disregarded when the buffer is full Reference e 2 10 1 Calling Using the Call Log Incoming Call Log KX T7533 KX T7536 KX T7230 KX T7235 only U M Parameter 56 Call Log Incoming Log Lock Default 57 SP NL JT 59 G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for turning on off the Call Log Incoming Log Lock A 3 digit password is needed Use it twice e g 57123123 to turn on the lock and use it once i e 57123 to turn off the lock For Manager Operator only Reference e 2 10 3 Denying Other People the Possibility of Seeing Your Call Log Incoming Call Log Lock KX T7533 KX T7536 KX T7230 KX T7235 only U M Parameter 57 Timed Reminder Remote Default 7 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for setting cancelling Timed Reminder Remote feature For Manager Operator only Reference e 3 1 1 Setting the Alarm for Other Extensions Remote Timed Reminder Wake Up Call U M System 51 2 3 Numbering Plan Parameter 58 Login Logout Default 45 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for Log in Log out Reference e 2 5 5 Leaving an Extension Group Log In Log Out U M Parameter 59 Automatic Callback Busy Cancel Default 46 Value Range 1 4 digits consisting o
168. nfiguration 19 1 5 VPS DPT Port Assignment Parameter Ext No 1 DN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the extension number for B1 channel Note e This programme allows you to assign an extension number to each Voice Mail port Since each port connected to the VPS provides two extensions this enables you to assign extension numbers to each port To reach the Voice Mail system users dial these extension numbers Reference 2 3 Numbering Plan P G Parameter Ext No 1 Group No Default Blank Value Range 1 128 Description Function Specifies the Extension Group 1 128 to which the B1 channel of the VPS DPT port is assigned Note e Specifies the extension group number to which the type of extension group VM or AA is assigned Reference e 1 3 System Features F G Extension Group 3 3 Extension Group P G Parameter Ext No 2 DN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the extension number for B2 channel Note This programme allows you to assign an extension number to each Voice Mail port Since each port connected to the VPS provides two extensions this enables you to assign extension numbers to each port To reach the Voice Mail system users dial these extension numbers Reference 2 3 Numbering Plan P G Configuration 1 5 VPS DPT Port Assignment Parameter Ext No 2
169. nfiguration 3 1 1 Configuration 1 1 Configuration Used to determine the basic system configuration A TD500 Maintenance Console rogramming ai INFEErDFeSienment Configuration 1 2 Slot Assignment 1 2 Slot Assignment Assigns the type of service cards inserted in the free slots in the basic and expansion shelves Note In some countries the El the E amp M and the ELCOT cards must not be connected to the Public Switched Network The DPH card is not available in some countries 1 1 Slot Assignment eibert Ile m rm m m m m UUL Configuration 7 1 2 Slot Assignment Parameter Card Type Default Value Range Description Function Reference Blank Specifies the type of service card inserted in the free slots in the basic and expansion shelves lt Selection gt None Not assigned BRI ISDN Basic Rate Access Interface card DHLC Digital Hybrid Line Circuit card DISA Direct Inward System Access card DLC Digital Proprietary Line Circuit card DPH Doorphone Circuit card El El Digital Trunk card E amp M E amp M card TIE Line card ELCOT Enhanced Loop Start Central Office Trunk card ERMT Enhanced Remote Circuit card ESLC Enlarged Single Line Telephone Circuit with Message Waiting card PRI30 ISDN Primary Rate Access Interface card Notes e To change the current Card Type to a new one delete the cu
170. ngle or all Operators in the group Multi simultaneously Assignable only when Operator is specified in Group Type programming Reference 1 3 System Features F G Operator Group 1 6 Originating Features F G Operator Call 120 Group 3 3 Extension Group Parameter Operator Setting Call Priority Default CO Call 1 Intercept Routing 2 Recall 3 Extension Call 4 Value Range Priority 1 4 Description Function Specifies the answering priority of incoming calls to the Operator Group by a type of call when more than one call is ringing at an Operator extension Assignable only when Operator is specified in Group Type programming Notes e Ifall extensions in the Operator group are busy incoming calls directed to the group will be put in the waiting queue in order of precedence determined by Call Priority setting e Ifthe same priority is set on all four types of calls the calls will be put in the waiting queue in order of the arrival Reference 1 3 System Features F G Operator Group 1 6 Originating Features F G Operator Call Parameter UCD Setting Time Table No Default None Value Range None 1 32 Description Function Specifies the UCD Time Table number for the UCD Group Reference e1 3 System Features F G Extension Group 1 5 Attended Features F G Uniform Call Distribution UCD Group 121 3 3 Extension Group Parameter UCD Setting
171. ns U M Features 187 5 4 Emergency Dial Code 5 4 Emergency Dial Code Used to programme a list of up to 10 emergency numbers that any extension in the system can dial at any time regardless of dialling restrictions 5 3 Emergency Dial Code BEE Dial Max 8 Digits ox amy comet tow Parameter Dial Default All Blank SP NL JT 1 110 2 112 G Value Range Up to 8 digits consisting of 0 9 Description Function Specifies emergency telephone numbers that can be dialled from any extension regardless of restrictions imposed by Toll Restriction Account Code Verified mode or Electronic Station Lockout Reference e 1 6 Originating Features F G Emergency Call e 2 2 1 Basic Calling U M 188 Features 5 5 Quick Dialling 5 5 Quick Dialling Used to store up to eight Quick Dial numbers 5 4 Quick Dialing Dial Max 16 Digits COO O S O O i EEE E HE 5 4 Quick Dialing M OK Apply Cancel Help Parameter Dial Default All Blank Value Range Up to 16 digits consisting of 0 9 x F P S or hyphen Description Function Specifies the phone number for Quick Dialling Note e Any extension user can use Quick Dialling number simply by dialling the feature number for Quick Dial 1 8 Reference e 1 7 Dialling Features F G Quick Dialling e 2 2 2 Easy Dialling U M Features
172. ns on DSS consoles You can enter into Flexible DSS Key screen in Section 4 4 2 Flexible DSS Key Assignment by clicking DSS Key button on this screen Reference e 4 1 2 Customising the Buttons U M Parameter PF Key Default Not Stored Value Range Please refer to Section 4 4 3 Flexible PF Key Assignment for DSS Console Description Function Used to determine the usage of PF Programmable Feature buttons on DSS consoles You can enter into Flexible PF Key screen in Section 4 4 3 Flexible PF Key Assignment for DSS Console by clicking PF Key button on this screen Reference e 4 1 2 Customising the Buttons U M 168 Line 4 4 DSS Console 4 4 2 Flexible DSS Key Assignment Used to determine the usage of flexible DSS buttons on DSS Consoles The following screen is displayed by clicking DSS Key button on 4 3 DSS Console screen Flexible DSS Key 77540 lt Key Type Assignment gt The following Key Type Assignment screen is displayed by clicking Not Stored button for each DSS Key on the above screen Flexible DS y gt Hot Stored EZT ion Line Ho url Tone Kingingiype Immediate Se Line 169 4 4 DSS Console lt Additional Parameters Required by Key Type gt Depending on a Key Type additional parameters are required as follows Additional aaa Key Type Paranieters Description SINGLE CO Trunk Line No
173. nscssstessessesvessssosssnssesvocecesuacensedoasesnssesssdeycovese rer Eee 216 6 Toll Restriction u sun anna ZLO 6 1 TOM RES tri Chi On ei scien cave EES A E T T EE TE E E E T O 220 6 2 TRS Deny Code oascccicssicnscvccvcdetscnstediacesbocecentsseanccossesdvntssunesssancongssuccsauswacsesssssseessenseenae 221 6 3 TRS Eycepti n Code iiiseccscsssescescescvsscsssdeassvessscssdsessseevecsnsveseceseedenstaessonssedecssossoessossses 223 7 ARS Automatic Route Selection ccccscsssssssscccssssssssssceeees DOO 7 1 ARS Automatic Route Selection ccccsssssssscssssssscsscccecsscscesscceccsscscessessccccesees 226 7 2 Time Tabl siaaa raiat EEVEE ES AEAN ASA E NAE EAA ESER 227 73 Leading Digits TaDle niosissinssoriississsenicesris srra i sis orsaken Nk anir ra rii s anasa 228 7 4 Routing Plan sesciseccscscsecsesscssescsecssscscesssescessecscesbeacecesesscsustsccsssssesseccescvessaestesssedessesessens 230 7 5 Digits Modification Table ccsccccsssssccsssssccssssscccssssccccsssscscsssscscsssssccssssccessssccsees 232 8 Private Network ca vscscincsvsdncenscenscassasevedsesseousanonscnnsssesnsedoasesieentasvans ZI S L Private Network nee een annna nenne tecentassdescdsansscasavedeadanvvssdersvecteese 236 8 2 TIE Routing Table s0065s 50050086 ns estastro n Sero seest ises seen 237 OD D B AA DI T D E E S sseceuvesteosessaneesons 240 9 2 Number Transformation eesessooesscossssocsssoossssosessooessoossssoossssoosssoosses
174. nsion users can call the extensions with this COS level Reference e 1 6 Originating Features F G Toll Restriction 61 2 4 Class of Service COS Parameter Switching Day Night Mode Default Value Range Description Function Reference Disable SP NL JT Enable G 1 Enable 2 Disable Enables or disables switching the Day Night service on a Class of Service COS basis e 2 11 4 Switching the Day Night Service U M Parameter Account Code Mode Default Value Range Description Function Reference Optional 1 Optional 2 Verify Toll 3 Verify All Specifies one of the following three Account Code Entry modes 1 Option mode An extension user can enter any account code if needed 2 Verified Toll Restriction Override mode An extension user can enter a pre assigned account code to override toll restriction 3 Verified All Calls mode An extension user must always enter a pre assigned account code when making any of the following outside calls unless it has previously been stored in memory e Last Number Redial e Saved Number Redial lt PT only gt e System Speed Dialling e One Touch Dialling lt PT only gt e Station Speed Dialling e Trunk Access Manual Dialling e 1 3 System Features F G Account Code Entry e 2 2 5 Calling without Restrictions U M 62 System 2 4 Class of Service COS Parameter SDN COS Defa
175. nsisting of 0 9 X or Description Function Specifies the Confirmation Tone code Sent to the VPS when it successfully dials a message waiting lamp on off code Reference e 1 3 System Features F G Integration VPS Parameter FWD to VM Ringback Tone Default 6 Value Range Up to 3 digits consisting of 0 9 X or Description Function Specifies the FWD to VM Ringback Tone code Sent to the VPS if the caller is forwarded to another VM Voice Mail port which is available to accept the call Reference e 1 3 System Features F G Integration VPS Parameter FWD to VM Busy Tone Default 7 Value Range Up to 3 digits consisting of 0 9 X or Description Function Specifies the FWD to VM Busy Tone code Sent to the VPS if the caller is forwarded to a VM port which is not available to accept the call Reference e 1 3 System Features F G Integration VPS Features 199 5 10 VPS Integration Parameter FWD to Extension Ringback Tone Default 8 Value Range Up to 3 digits consisting of 0 9 X or Description Function Specifies the FWD to Extension Ringback Tone code Sent to the VPS if the caller is forwarded to another non voice mail extension Reference e 1 3 System Features F G Voice Mail Command Integration VPS Voice Mail Commands are used to control the activity of VPS There are the following four Voice Mail Commands Leave Message Get Message AA Automated Attendant Service and VM Voice Mail
176. nsole 6 porto L o Pre porn OO O O Bere Model E modes eo Er DSS Console 3 DSS Console 7 Port No 188 key PrRey Potiki 00 pss Key PAREY Model Leony a moder E52 257 DSS Console 4 DSS Console 8 Porno L E Frl porn ___ 1 BSS Key BE Model Ra moder eo Er 43 DSS Console Cancel Help 4 4 1 DSS Console Copy Used to copy a part of or all settings of a certain DSS Console to all other DSS Consoles at a time You can also specify one or several DSS Consoles as the copy destination Copying the DSS Console Parameters to Other DSS Consoles 1 Edit the parameters of the copy source DSS Console and save it 2 Point to the Copy button on 4 3 DSS Console screen of the copy source and click e DSS Console Copy screen is displayed e The current DSS Console copy source number is shown as Copy from XXX XXXXX XX 166 Line 4 4 DSS Console Copyfrom 102 DHLC 07 Copy Item Destination DSS Console Card Port DSS Key 403 DHLC 07 I PF Key 3 Select the DSS Console parameters to copy in Copy Item field e Items marked with W are copied 4 Point to the Select All button in the Destination DSS Console field and click e All displayed Extension Line Nos will be highlighted e You can also specify one or several DSS Consoles as the copy destination by clicking it them directly 5 Point to the Execute butto
177. nt Start Time Os First Digit Time 10 s SP NL JT 5 s G Inter digit Time 5s Intercept Time 12 rings Call Forwarding No Answer Time 3 rings Extension to CO Line Call Duration Time 10 min CO to CO Line Call Duration Time 10 min Automatic Redial Interval Time 60 s Automatic Redial Repeat Times 10 times SP G 4 times NL 15 times JT Door Opener Time 5s 292 Default Values 2 5 2 System Timer 2 2 Program Default Timed Reminder Ringing Time 30s Call Parking Recall Time 605 TIE Inter digit Time 5s DISA Prolong Time 3 min DISA Delayed Answer Time 1 ring Timed Reminder Arrive Count 3 times DISA Automated Attendant Time ls DISA IRNA Time 60 s Intercept Timer after OGM 5s Timed Reminder Arrive Wait Time 60s 2 6 Local Hunt Sequence Program Default Trunk Group No 01 1 Others None 2 7 Trunk to Trunk Restriction Program Default Source Trunk Group No 1 Destination Trunk Group No 1 48 No check 2 8 System Option 2 8 1 System Option 1 4 Program Default 1 Sound source during transfer Music on Hold 2 SLT On hook with consulting held call Consulting Hold 3 FLASH button operation while CO talking Don t release the trunk SP NL Release the trunk JT G 4 FLASH button operation when Don t release the trunk is selected at 3 Sending EFA signal SP NL Disconn
178. ommand must not exceed 16 digits Truncate it Truncate means that the leading 16 digits are saved and the rest are deleted Ww5011 Local Area Code must not exceed 6 digits Truncate it Truncate means that the leading 6 digits are saved and the rest are deleted W5012 Additional dial must not exceed 4 digits Truncate it Truncate means that the leading 4 digits are saved and the rest are deleted W5013 Caller ID name must not exceed 16 characters Truncate it Truncate means that the leading 16 characters are saved and the rest are deleted W5014 Caller ID number must not exceed 24 digits Truncate it Truncate means that the leading 24 digits are saved and the rest are deleted W5020 Rate must not exceed 8 digits Truncate it Truncate means that the leading 8 digits are saved and the rest are deleted W5021 Currency must not exceed 2 characters Truncate it Truncate means that the leading 2 characters are saved and the rest are deleted Programming Error Messages 281 11 2 Warning Messages WXXXX Message Code Description W7001 ARS Leading dial must not exceed 10 digits Truncate it Truncate means that the leading 10 digits are saved and the rest are deleted W7002 ARS additional dial must not exceed 20 digits Truncate it Truncate means that the leading 20 digits are saved and the rest are deleted W8001 PBX code must not exceed 3 digits Truncate it Truncate means that the
179. on Used to assign ARS parameters A TD500 Maintenance Console Programming J So as 5 226 ARS Automatic Route Selection 7 2 Time Table 7 2 Time Table Used to make up ARS time schedules It is possible to split a day into four time zones maximum so that the least expensive line is selected for that time Enter the starting time of each zone according to the service hours and charges offered by your carriers 7 1 ARS Time Table See sun os oofam ps oo pm ps o0 pm po 00 bisabie mon fos oofam fos o0 pm gt 09 o0 pm po 00 pisable tue fs oofam 05 o0 pm fps o0 pm fo 00 pisabie wen foe oo am 05 oo pm os o0 pm oo 00 pisabie m tHu fs oofam gt s oo pm p9 oofem gt fo 00 nisable gt sat os oofam gt 05 00 pm jj p9 00 pmm gt fo 00 nisabte au rear eal ee Parameter Time A B C D SUN MON TUE WED THU FRI SAT Default Time A 8 00AM Time B 5 00PM Time C 9 00PM Time D Disable Value Range Hour 01 12 AM PM Disable Description Function Specifies starting time Hour 01 12 AM PM Disable of the applied Route List Reference 7 4 Routing Plan P G ARS Automatic Route Selection 227 7 3 Leading Digits Table 7 3 Leading Digits Table Used to determine the appropriate Route Plan Table number for a call by analysing the extension user dialled number Up to
180. on visscsiessccscsssceelecsucecesssccercssecevesscdeves sccuvesvesccnsssscceteosecctessecnvessdeatesssedbcensecces 78 Language Data ss ciscccccscccssceccisscesesssscscesvecscestvescesteececs eececsesececeseveescertssacesveeecerssedecersedecess 98 GOUD aan LOL GOYOUP PN T E SE E E E E E deere thesstesesececseacecsteeues 102 Tronk Gronp aore n A RETE ENERE UE NE OA N NA 103 Extension GrOU P seansini bunama na A aN uhren ee ee 114 Pasi Group aerieni aii ENE EEEE ENN 124 DIL I N Group sii cisectsccsencssasescesdecncssdsonsvoseesnseesinsecs dance sveedensscsceeeetcdsnedssgnesvocbesnaveasenss se 125 OGM Grou D eeann eaaa inaani e Aa AAN AREARE VEEE EA 128 Bii E A E EE E E EERTE WOM 61 o EEEE EREE EEEE EE EEEE E 132 Tink Liena AE EN RA NEE 133 Extensio n Line e se aren asariar Ei iay NEEE E ENS AEA AA E ASSES 147 DSS COnSOle EE E E EE EA EE esse RReee Re eree 166 DOr PR OMe ese ccsccssssavsveccecssesecctsececctsedssceessescescesscaccsesceccses SKAKAR REAA EEAS a 174 External Paging 2c sisecccctiecensetacctctseceeccchustcccececdessssuencosecctsonsectccceuctccdsstbcdeseatisceasuscsonses 176 ISDN Extension Lite 05 3ci csccssesacesssovssessnossesvesesecevoseecdeisoscasesscesssossvssnssseossuetosshess es 178 Feature Ran RE 185 ik cr 1 111 g SC esses AE A sessszeas scenes E IA E EE A sadedss sasncesseastucsaces 184 System Speed Dialling sccciscsccoscossseascasdccontesscccondasconacscesssvonsosenessacessestaevdsseonsesssessassssess 185 Phanto
181. onds of the Timed Reminder alarm Reference e 1 8 Ringing Features F G Timed Reminder Wake Up Call Timed Reminder Remote Wake Up Call e 2 7 1 Setting the Alarm Timed Reminder Wake Up Call U M e 3 1 1 Setting the Alarm for Other Extensions Remote Timed Reminder Wake Up Call U M Parameter Call Parking Recall Time Default 60s Value Range 0 1800 s Description Function Specifies the length of time in seconds the system is to wait before alerting Call Parking Recall the extension who parked the call Note If 0 is specified Call Parking Recall does not occur Reference e 1 10 Holding Features F G Call Park 2 4 1 Holding a Call U M 72 System 2 5 System Timer Parameter TIE Inter digit Time Default 5s Value Range 3 30 s Description Function Specifies the maximum time allowed between digits on a TIE call after it was received by the system Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter DISA Prolong Time Default 3 min Value Range 0 7 min Description Function A CO to CO line call duration is initially limited by CO to CO Line Call Duration Time However prolonging the CO to CO call duration is possible To prolong his her call the caller should press any dialpad key except x The amount of prolonging is set by DISA Prolong Time 0 7 minutes If this is set to zero then prolonging is disabled Depending on 13 DISA pro
182. ontrol CPC Signal Detection Parameter Start Signal Type Default Value Range Description Function Reference Wink 1 Immediate 2 Wink Specifies the start signal type for a TIE E amp M trunk 1 Immediate The system sends the dialling digits to CO after waiting for the time length determined by First Dial Timer in Card Properties screen of the corresponding trunk card For information on Card Properties screen please refer to Card Type in Section 1 2 Slot Assignment 2 Wink The system sends the dialling digits to CO after receiving the wink signal 3 1 E amp M Features F G E amp M TIE Line Service 142 Line 4 2 Trunk Line Parameter Wink Signal Time out Default Value Range Description Function Reference 1024 ms 64 ms 128 ms 256 ms 512 ms 1024 ms 2048 ms 4096 ms 8128 ms zensuprpupe Specifies the length of time in milliseconds that the system is to wait for the Wink Signal after seizing the trunk Assignable only when Start Signal Type is set to Wink the case of the E amp M card is excluded 3 1 E amp M Features F G E amp M TIE Line Service Parameter Reverse Signal Detection Default Value Range Description Function Reference Disable SP NL JT Enable G 1 Enable 2 Disable If an ELCOT card KX TD50180 is installed in the system reversal of CO line polarity is monitored
183. oocesoossssossssoossso 241 10 Maintenance essssesessseesssssoessscesssssosssssesosssosssssessssssssssseessssso 247 1041 Maintenance seinciiccedsciccccnnsccetisisesceduocsvessoleesenscccseseeceseceedsesesecaancstcecesnsebencsestucsenoressess 248 10 2 External Modem 1 2 os ccccccccccccssccscvcecscuscssesecsscscvesveevcesseuce sen une ovsascveceveeceesvescecvesuncts 249 10 3 External Modem 2 2 cis scccsssecccsccccsccssessescencccescocctssceeesssconesescscovesseoesesccesoctscteeccscesesve 251 10 4 SMDR 2 n 2 20m Ra ITEE A E 252 10 5 Power Failure Transfer 00000000000000000000000000snenensnensnsnennensnnsnssnenensnsnsnsnensennene 258 10 6 System Parameters ccccccscesscsscesteccssescecssescceseccicesesesecsssetesessedesecssescessssccsossccdsertsetees 260 10 7 System Tite iseesivscsssscsccnsccssncsenscevooesconsosscsoesessenessvescessvesteatsasedsesecesentsdsesosevecsnsseseenes 265 11 Programming Error Messages esssssssssssssssnnnnssssssnsnenssssnsseenee 209 11 1 Error Messages EXXXR ses scasscccsedesciessesciesseaastssosenstessacseossedsssestestsnescacasedasteseacoes 270 11 2 Warning Messages WXXXX sccccssssscssssscsssscsssssssssssscssscssesesssssecessssssesssssesees 280 11 3 Information Message IXX XX cccsccsssssscssssssssssssssccsssssscsssscssssssssssscssssssssseecs 283 12 Default Value een 285 Index Table of Contents Section 1 Configuration Co
184. oup that the extension user can use for making an outside call The following screen is shown on the display by clicking Class of Service screen IV no1 IV D13 M m3 MV D25 IV N25 M D37 Iv N37 D Day 7 Hot restricted lv 002 V 003 M n02 V NO3 MDa VW D15 Vania VW N15 IV D26 v D27 IV N26 V N27 Iv D38 V 039 IV N38 V N39 Iv 04 Iv n04 M D16 M N16 IV D28 IV N28 M D40 IV H40 V 005 v D06 IV NOS V NOG Mr M D18 Mz M ms M p29 V D30 M H29 V N30 Von M p42 MUN M H42 N Night 01 48 Trunk Group No 7 Restricted Iv 007 Iv no M p19 M ms M D31 M N34 VD3 VW N43 Iv D08 Iv nos Iv D20 Iv N20 Iv D32 IV N32 vos IV H44 Iv 009 IV Nog M 024 M H21 M D33 M H33 IV D45 M N45 M D10 Iv N10 Iv 22 IV N22 V 034 IV N34 Iv D46 IV N46 Trunk Group Setting button on Iv p11 M n11 Iv D23 IV H23 V 035 M N35 IV Da Iv naz Iv D12 IV N12 M D24 M H24 V D36 IV N36 Iv D48 IV na8 System 65 2 4 Class of Service COS Parameter Trunk Group No 01 48 Day Night Default All Check Value Range 1 No check Restricted 2 Check Not restricted Description Function Specifies the trunk group 01 48 which the extension user can use for making an outside call in Day Night mode respectively on a COS number basis Reference e 1 3 System Features F G Trunk Group 32 Trunk
185. ployed Reference e 1 3 System Features F G Tenant Service 2 2 Tenant P G 176 Line 4 6 External Paging Parameter FDN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the FDN Floating Directory Number for the External Pager Reference e 1 3 System Features F G Floating Station Parameter BGM Default No check Value Range 1 No check Disable 2 Check Enable Description Function Specifies whether BGM is sent or not when the External Pager is idle Whether sound actually comes out of External Pager or not is controled by the Manager or Operators Reference 3 2 1 Turning on the External Background Music Background Music BGM External U M Parameter BGM Source Default MUSI Value Range 1 None 2 MUSI 3 MUS2 Description Function Assigns the External Music Source port to which the External Pager is connected To change music sources you must first select and apply None Then you can select and apply MUS1 or MUS2 Note e If MUS2 is selected the actual source depends upon the position of the switch located on the TSW card MUS2 Music 2 jack or INT MUS internal music can be selected by this switch Reference 2 8 3 Music Source External Internal I M 177 4 7 ISDN Extension Line 4 7 ISDN Extension Line Used to assign parameters for ISDN Extension Lines 4 6 ISDN Extension Line Card Ho 492
186. port is defective Reference None Configuration 11 1 4 Extension Port Assignment 1 4 Extension Port Assignment Used to set various parameters for extension ports XDP extensions are on ports 9 through 16 of a DHLC card 1 3 Extension Port Assignment Be Corano T ee Attribute Tel Type DN GroupNo Parallel XDP Status Unknown parane ms 2 2 TEL gt 17230 1 gt Paraner gt ms 3 Unknown Parallel INS 4 TeL v 17536 h zl Parallel ms s nic a 6 TEL x 17533 1 Paranei INS 7 Unknown h Parallel INS 8 reL Unknown 1 gt Paranei gt ms al DH Refer n amy cance tt Parameter Card No Default Value Range XXX YYY XXX Card No 101 314 YYY Card Type Description Function Specifies the physical number of the extension card and its type which you are going to programme Reference 1 2 Slot Assignment P G 12 Configuration 1 4 Extension Port Assignment Parameter Attribute Default Value Range Description Function Reference TEL 1 TEL 2 DSS 3 VPS DPT Specifies the attribute of the terminal which is to be connected to the extension port 1 TEL Select this option when you connect a telephone set to the extension port 2 DSS Select this option when you connect a DSS console to the extension port 3 VPS DPT Select this option when a port of Panasoni
187. r Group No Default Display only Value Range 1 128 Description Function Displays the Extension Group to which the selected extension port is assigned Note e Default Group No for Ext 1001 SP NL JT 20001 G is 128 Reference 1 4 Extension Port Assignment P G Parameter DN Default Value Range 3 4 digits consisting of 0 9 Description Function Specifies the extension number which you are going to programme Reference 2 3 Numbering Plan P G 149 4 3 Extension Line Parameter Name Default Blank Value Range Up to 10 characters consisting of 0 9 A Z a z or the following marks x 3 lt gt 7 amp Description Function Specifies the name for the extension line Note e This is shown on the called party s display PT so that he she knows who is calling Reference e 1 17 Display Features F G Display Call Information Parameter COS No Primary Default 1 Value Range 1 96 Description Function Specifies the Primary COS Class of Service number to the extension Reference e 1 3 System Features F G Class of Service COS e 3 1 5 Changing Service Level of Extensions Switching COS U M Parameter COS No Secondary Default 1 Value Range 1 96 Description Function Specifies the Secondary COS Class of Service number to the extension Reference e 1 3 System Features F G Class of Service COS e 3 1 5 Changing Service Level of Extensions Switching COS
188. r button LCS Live Call Screening button LCS CANCEL Live Call Screening Cancel button DAY NIGHT Day Night switching button ALARM Alarm button ANSWER Answer button RELEASE Release button TONE THROUGH Tone Through button SS ISDN Service button ALERT Alert button Notes SS ISDN Service button is used for ISDN Network Service Access feature Please refer to Section 2 2 ISDN Originating Features in the Features Guide This service may not work properly if your ISDN Service carrier does not support this service e The KX TD500 System is designed and manufactured in accordance with the following ETS European Telecommunication Standard specifications ETS 300 122 Generic Keypad protocol for the support of supplementary Services 4 1 2 Customising the Buttons U M Line 163 4 3 Extension Line 4 3 3 Flexible PF Key Assignment for PT Used to determine the usage of flexible PF buttons on PTs The following screen is displayed by clicking PF Key button on 4 2 Extension Line screen Flexible PF Key EXT1001 lt Key Type Assignment gt The following Key Type Assignment screen is displayed by clicking Not Stored button for each PF Key on the above screen FI exible PF Ke y xi fot Stored name 164 Line 4 3 Extension Line lt Additional Parameters Required by Key Type gt Depending on a Key Type additional parameters are required as follows
189. r dialled and If your CO is such a type select No check Reference e 1 6 Originating Features F G Toll Restriction for Special Carrier Access Parameter 8 Confirmation tone for Override Barge in Conference and Privacy Release Default Enable Value Range 1 Enable 2 Disable Description Function Allows you to remove Confirmation Tone 4 This tone is sent when a three party conference is established finished Reference e 1 13 Audible Tone Features F G Confirmation Tones Parameter 9 Confirmation tone for Call Pickup Paging Answer TAFAS Answer Hold Retrieve and Call Park Retrieve Default Enable Value Range 1 Enable 2 Disable Description Function Allows you to remove Confirmation Tone 3 This tone is sent when a conversation is established just after an extension user dials the feature number for accessing the following features Call Pickup Paging Answer TAFAS Answer Hold Retrieve and Call Park Retrieve Reference e 1 13 Audible Tone Features F G Confirmation Tones System 81 2 8 System Option Parameter 10 Station Speed Dialing Initial display Default Name Value Range 1 Name 2 Number Description Function Specifies the initial display of a display DPT such as KX T7235 KX T7536 in Station Speed Dialling Reference 2 10 4 Using the KX T7531 KX T7533 KX T7536 or KX T7235 U M 2 8 2 System Option 2 4 Used to assign system option parameters No 11
190. ram Default Key Type Not Stored 4 4 3 Flexible PF Key Assignment for DSS Console Program Default Key Type Not Stored 4 5 Doorphone Program Default Card No Port No 1 Default Values 301 Program Default Tenant No 1 Destination Day Night Blank 4 6 External Paging Program Default Pager No Display only Tenant No 1 FDN Blank BGM No check BGM Source MUSI 4 7 ISDN Extension Line Program Default Card No Port No 1 Group No Display only Name Blank Charge Limit 0 Tone Disable ISDN Bearer Mode Automatic Numbering Plan ID Default Type of Number Default CLIP COLP Number Public Blank CLIP COLP Number Private Blank COS No Primary 1 COS No Secondary 1 302 Default Values 5 Features 5 1 Features 5 2 System Speed Dialling Program Default Tenant No 1 Entry No 000 019 Max Entry Display only Current Registration Display only Name Blank Number Blank 5 3 Phantom Extension Program Default Entry No 001 048 FDN Blank 5 4 Emergency Dial Code Program Default Dial All Blank SP NL JT 1 110 2 112 G 5 5 Quick Dialling Program Default Dial All Blank 5 6 Account Code Program Default Tenant No 1 Entry No 0001 0020 Code Bl
191. rd 3 Digits i __i Station Lock Password ISDN Bearer Mode Be JOG Dial Speed CLIP COLP Number Max 16 Digits Call Log Incoming Ma Overwrite Mode Yes Private Lock Password 3 Digits n 4 3 1 Extension Line Copy Used to copy a part of or all settings of a certain Extension Line to all other Extension Lines at a time You can also specify one or several Extension Lines as the copy destination Copying the Extension Line Parameters to Other Extension Lines 1 Edit the parameters of the copy source Extension Line and save it 2 Point to the Copy button on 4 2 Extension Line screen of the copy source and click e Extension Line Copy screen is displayed e The current Extension Line copy source number is shown as Copy from DN XXXX Line 147 4 3 Extension Line Extension Line Copy Copyfrom DH 1001 r Destination Extension Line DH Card Port Hame 103 DHLC IV Initial Display Selection 403 DHLC IV Preferred Line 103 DHLC IV Data Line Mode Er 2 IV Call Waiting Tone Type ie IV Call Pickup Deny 403 DHLC IV Language 103 DHLC IV LCS Setting 103 DHLC IV Station Lock Password his Te 3 IV Call Log Incoming 403 DHLC IV Pickup Dialing 103 DHLC IV Charge Limit tes E IV CLIP COLP Number 406 DLC 01 IV CO Key 406 DLC 02 IV PF Key IV JOG Dial Speed Select All IV ISDH Bearer Mode Execute Cancel Help 3 Select
192. rdance with the following ETS European Telecommunication Standard specifications ETS 300 122 Generic Keypad protocol for the support of supplementary services e 2 2 ISDN Originating Features F G Calling Line Identification Presentation CLIP e 2 3 ISDN Answering Features F G Connected Line Identification Presentation COLP Parameter CLIP COLP Number Private Default Value Range Description Function Reference Blank Up to 16 digits consisting of 0 9 X or P PAUSE Specifies a CLIP COLP number used for the incoming outgoing calls via Private Network to each extension Note e The KX TD500 System is designed and manufactured in accordance with the following ETS European Telecommunication Standard specifications ETS 300 122 Generic Keypad protocol for the support of supplementary services e 2 2 ISDN Originating Features F G Calling Line Identification Presentation CLIP e 2 3 ISDN Answering Features F G Connected Line Identification Presentation COLP 158 Line 4 3 Extension Line Parameter Charge Limit Default 0 Value Range 0 No limit 1 99999 The number of charge meter allowable for the extension Description Function Used to determine the sum total of telephone charge allowable to extension users on an extension basis If the telephone charge on the extension exceeds the limit a toll call cannot be made anymore from that extension Not
193. rence 2 4 Class of Service COS P G 196 Features 5 10 VPS Integration 5 10 5 10 1 VPS Integration VPS Integration 1 2 Used to assign Integration Code and Voice Mail Command for VPS Integration 5 10 VPS Integration 1 2 Sax r Integration Code DTMF Signal Max 3 Digits Ringback Tone boo Extension Disconnection Busy Tone es Confirmation Tone pi Reorder Tone Bf FWD to VM Ringback Tone eo DHD Tone bpo FWD to VM Busy Tone Extension Answer 6 FWD to Extension Ringback Tone Voice Mail Command Max 16 Digits Leave Message ho 4A Service Get Message feo VM Service ox amy came tow Integration Code When DTMF tone Integration is activated the KX TD500 informs the VPS Voice Processing System of the state of the call busy answered ringing etc by sending a code with DTMF tone before sending the normal call progress tone busy tone ringback tone etc These codes enable the VPS to immediately recognise the current state of the call and improve its call handling performance Parameter Ringback Tone Default 1 Value Range Up to 3 digits consisting of 0 9 X or Description Function Specifies the Ringback Tone code Sent to the VPS when the extension it dialled is ringing Reference e 1 3 System Features F G Integration VPS Features 197 5 10 VPS Integration Parameter Busy Tone Default 2 Value Range
194. res F G Direct Dialling In DDD 3 1 E amp M Features F G E amp M TIE Line Service Parameter Answer Wait Timer Default Value Range Description Function Reference None 1 None 2 1 min 3 2 min 4 3 min 5 4 min Specifies the length of time in minutes the system waits after an outgoing CO call is made before the other party answers the call If the call is not answered before this timer expires the call will be disconnected automatically Assignable only when E1 ELCOT card is installed in the system Note e In some countries the El and the ELCOT cards must not be connected to the Public Switched Network None 146 Line 4 3 Extension Line 4 3 Extension Line Used to assign parameters for extension lines 4 2 Extension Line BEE cwano orome porn z m e ee Hame Max 10 Characters Message Lamp Mailbox Ho 3 or 4 Digits CO Key PE Key Initial Display Selection Charge COS Ho i cater primary 5 Secondary Preferred Line Pickup Dialing Di Mode r Dial Outgoing Prime LineICM PDN 7 une key io C Enable Disable Incoming RingingLine Kev Ho Data Line Mode Call Waiting Tone Type _ LCS Setting CYes Ho Tone1 C Tone2 Status Inactive C Active Operation Mode Private Hands free oles neoe Recording Mode Keep Rec Stop Rec Enable Disable English C Option LCS Passwo
195. ribution UCD 122 Group 3 3 Extension Group Parameter UCD Setting LOGIN Monitor Default Disable Value Range 1 Disable 2 Enable Description Function Specifies whether the extension can monitor through the corresponding DSS buttons the Login Logout status of UCD Group members or not Reference e 1 3 System Features F G Extension Group 1 5 Attended Features F G Uniform Call Distribution UCD e 2 5 5 Leaving an Extension Group Log In Log Out U M Parameter UCD Setting UCD Call Waiting Default Enable Value Range 1 Disable 2 Enable Description Function This feature is different from regular Call Waiting This feature if enabled allows UCD group members to hear a Call Waiting tone when an inside outside call arrives but all the extensions in the UCD Group are busy Notes e To use this feature this setting must be set to enable e In addition each extension must enable regular Call Waiting Reference e1 3 System Features F G Extension Group 1 5 Attended Features F G Uniform Call Distribution UCD Group 123 3 4 Paging Group 3 4 Paging Group Used to programme up to 16 Paging Groups Each Paging Group consists of up to 24 Extension Groups One Extension Group can be assigned to only one Paging Group 3 3 Paging Group Se 2 3 4 None gt 10 Hone gt 16 Hone gt 22 Hone gt 5 m 7 23 6 Hone x 12 None M 18 Hone x 24 None x
196. rrent setting first by selecting None and then assign a new Card Type e CPU Slot No 13 of the Basic Shelf is fixed to CPU Central Processing Unit card e TSW Slot No 14 of the Basic Shelf is fixed to TSW T Switch card e Card Properties Card Properties screen lists and lets you customise the operating characteristics associated with the following optional cards Extension Cards DHLC DLC ESLC Trunk Cards E amp M El ELCOT BRI PRI30 Resource Cards ERMT DISA e Editing Card Properties Parameters You can edit Card Properties parameters according to your needs To go to Card Properties screen click Card Type button of the target card on this screen Then click Properties button Help File You can get information on Card Properties Parameters by clicking Help button on this screen e 1 4 Service Cards Description I M Configuration 1 2 Slot Assignment Parameter Status Default Value Range 1 INS 2 OUS 3 FAULT Description Function Used to set the status of the service cards 1 INS In Service The target service card is operating normally 2 OUS Out of Service Programming data for the target service card is entered but the target service card is not assigned to the system 3 FAULT The target service card is defective hardware In this case the LED indicator on the service card is lit Reference None Configuration 9 1 3 Trunk Port Assignment
197. rts 1 8 BRI Port Assignment ioii Line Port Type DN Group No Status E zei i D3 Bee 4 I 3 s co 4 7 co 1 DH Refer 1 8 BRI Port Assignment OK Apply Cancel Help Parameter Card No Default Value Range XXX BRI XXX Card No 101 314 Description Function Specifies the physical number of the BRI card which you are going to programme Reference e 1 2 Slot Assignment P G Parameter Type Default CO Value Range 1 CO 2 EXT Description Function Specifies the type of each BRI port either CO CO line or EXT extension line on a BRI port basis Reference e 2 1 ISDN Features F G Integrated Services Digital Network ISDN Integrated Services Digital Network ISDN Extension 4 7 ISDN Extension Line P G Configuration 1 8 BRI Port Assignment Parameter DN Default Blank Value Range 3 4 digits consisting of 0 9 or X Description Function Specifies the DN Directory Number for the BRI port Assignable only when EXT is specified in Type assignment Note e X can be used as a wild card character which substitutes any digit in its position The last one or two digits of DN may be xe Reference 2 3 Numbering Plan P G Parameter Group No Default 1 Value Range 1 48 or 1 128 Description Function Type CO Specifies the Trunk Group 1 48 to which the BRI port is assigned Type EXT Specifies the Extension Group 1 128
198. s F G Night Service 35 2 2 Tenant Parameter Music on Hold Source Default MUSI SP NL G Tone JT Value Range 1 None 2 MUSI 3 MUS2 4 Tone Description Function Specifies the Music Source port to be used for Music on Hold Note e If MUS2 is selected the actual source depends upon the position of the switch located on the TSW card MUS2 Music 2 jack or INT MUS internal music can be selected by this switch Reference e 1 3 System Features F G Music on Hold e 2 3 2 TSW Card I M Parameter BGM Source Default MUS1 Value Range 1 None 2 MUSI 3 MUS2 Description Function Specifies the Music Source port to be used for BGM Note e If MUS2 is selected the actual source depends upon the position of the switch located on the TSW card MUS2 Music 2 jack or INT MUS internal music can be selected by this switch Reference e 2 8 3 Music Source External Internal I M 36 System 2 2 Tenant Parameter Automatic Route Selection Default No check Value Range 1 Check Enable 2 No check Disable Description Function Specifies whether to utilise ARS Automatic Route Selection or not If set to No No check Trunk Access Idle is activated instead of ARS when an extension user dials 9 for making an outside call Reference e 1 6 Originating Features F G Automatic Route Selection ARS 7 1 ARS Automatic Route Selection P G
199. s of the tenant but trunk groups will be skipped if they do not belong to the same tenant as the extension user Reference e 1 6 Originating Features F G Trunk Access Idle 76 System 2 7 Trunk to Trunk Restriction 2 7 Trunk to Trunk Restriction Used to allow or restrict the trunk to trunk relay function routing a trunk call from one Trunk Group to another on a trunk group basis Please refer to TIE Line Network Alternate Routing in Section 3 1 E amp M Features of the Features Guide for further information 2 6 Trunk to Trunk Restriction Source Trunk Group No Destination Trunk Group No Om ogo mw om on Ce om 8 u ae a Ol a3 nal 16 167 Al Aal asf 20f 2af 221 23f 2am 26 26f 271 28 29 sof aif 32 33f 3af 31 36r sr ss 39f aol af al al Mal a6f aef a7f ast 7 Notrestricted Restricted ox wy comet te Parameter Source Trunk Group No Default 1 Value Range 1 48 Description Function Specifies the source trunk group the first point of trunk to trunk relay number which you are going to programme Reference 3 1 E amp M Features F G E amp M TIE Line Service Parameter Destination Trunk Group No 1 48 Default No check Value Range 1 No check Restricted 2 Check Not restricted Description Function Specifies the destination trunk group the second point of trunk to trunk relay number which you allow to accept a trunk call from the so
200. s the telephone number or feature access number up to 24 digits consisting of 0 9 x P S or F Note P Pause S Secret Dialling F Hook Flash Parameter Key Type Default Value Range Description Function Reference Not Stored Please refer to Description Function Not Stored Key Type is not assigned ONE TOUCH One Touch Dial button FWD DND Call Forwarding Do Not Disturb button SAVE Saved Number Redial button ACCOUNT Account Code entry button CONF Conference button ANSWER Answer button RELEASE Release button SS ISDN Service button e 4 1 2 Customising the Buttons U M Line 173 4 5 Doorphone 4 5 Doorphone Used to assign the destination extensions for incoming calls from doorphones Note The DPH card is not available in some countries 4 4 Doorphone Card No 108 DPH See Port Ho gt Tenant No 1 Destination Day 3 4 Digits N Y N a a N o S amp S N Y N N oo YS S gt gt an N gELLLLLLE EDEN etliche N Destination Hight 3 4 Digits d a ne O O amp ese 2 mE ml Ey mE Em mm m mE 1 ee E E ml E u u L CE L e a BE Ta E wE 1 E BE EEE Es Parameter Card No Default Value Range XXX DPH XXX Card No 101 314 Description Function Specifies the physical number of a doorphone card which
201. sabled to communicate correctly It depends on the type of the modem you use In most cases hardware flow control can be disabled by sending the amp KO command from the PBX to the external modem Please refer to the manual of the external modem you use for further information It is recommended to add this command to Automatic Initialisation Command the command to initialise the modem automatically every time an external modem is plugged into the RS 232C Port 1 250 Maintenance 10 3 External Modem 2 2 10 3 External Modem 2 2 10 1 External Modem 2 2 o a 22 Bw N a a A U N a Connection Message Max 80 Characters isconnection Message Max 80 Characters CONNECT eee FT e ZZ o carrer O OOO O O f m o 10 1 External Modem 2 2 xl OK Apply Cancel Help Parameter Connection Message 1 5 Default Message 1 CONNECT Others Blank Value Range Up to 80 characters consisting of 0 9 A Z a z or the following marks x lt gt amp Description Function Specifies Connection Message from Modem Reference e 1 3 System Features F G External Modem Control e 2 11 1 Controlling the External Modem External Modem Control U M Parameter Disconnection Message 1 5 Default Message 1 NO CARRIER Others Blank Value Range Up to 80 characters consisting of 0 9 A Z a z or the following Description Funct
202. sing the Same Extension Number and the Setting of Your Previous Extension Walking Station U M 55 2 3 Numbering Plan Parameter 96 CLIP COLP Default 711 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for turning on off the CLIP COLP Calling Connected Line Indentification Presentation feature Reference e 2 7 5 Displaying Your Number on the Called Party and Calling Party s Telephone Calling Connected Line Identification Presentation CLIP COLP U M Parameter 97 CLIR Default 59 SP NL JT 57 G Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for turning on off the CLIR Calling Line Identification Restriction feature Reference e 2 7 6 Preventing Your Number Being Displayed on the Called Party s Telephone Calling Line Identification Restriction CLIR U M Parameter 98 COLR Default 58 Value Range 1 4 digits consisting of 0 9 X or Description Function Specifies the feature number for turning on off the COLR Connected Line Identification Restriction feature Reference e 2 7 7 Preventing Your Number Being Displayed on the Called Party s Telephone Connected Line Identification Restriction COLR U M Parameter 99 Dial Information CTI Default Blank Value Range 1 4 digits consisting of 0 9 or Description Function Specifies the feature number
203. sion CPC Signal Default 48 ms SP None NL JT G Value Range None 16 240 ms in 16 ms increments Description Function Specifies whether or not the system sends the CPC signal to an extension Reference None System 2 8 System Option Parameter 40 TSW Tone Selection Default TONE A Value Range 1 TONE A 2 TONE B 3 TONE C 4 TONE D Description Function Specifies the tone pattern in the TSW Tone ROM Reference None Parameter 41 Fixed Feature Number Default Type 2 Value Range 1 Type 1 2 Type 2 Description Function Specifies a type of Fixed Feature Numbers Reference e 1 3 System Features F G Flexible Numbering e 5 2 Feature Numbers List U M Parameter 42 DPT Ringer OFF Default Enable SP NL G Disable JT Value Range 1 Enable 2 Disable Description Function Specifies whether the Ringing tone of DPTs Digital Proprietary Telephones can be turned off or not Reference None Parameter 43 LCD Time Display Mode Default 12 h SP 24 h NL JT G Value Range 1 12h 2 24h Description Function Specifies the time display on the LCD in 12 hour or 24 hour notation Reference e 1 17 Display Features F G Display Date and Time System 95 2 8 System Option Parameter 44 Hotel Application Default Disable Value Range 1 Enable 2 Disable Description Function If enabled the Manager and the Operators can handle Front Oper
204. ss5se22000l cssediesstesdecsecensssecdesssecbsacasnted ocsseedecsessdaseveeueassesssccsesnssceans 7 Trunk Port ASSIGMMENL cccc cesescocesescssesesesscsssecsacesecssvesencecesencssesebescesabescceusncsasesecsoseseses 10 Extension Port Assignment esssecssssssesonsssennsssnnosssnnnsnsssnnssnssssnsnsssnnsnsssnnssssssnssnssnsssnnne 12 VPS DPT Port Assignment 00 sscsceoseseesssecssooscessanssessesesessoensessnessecnsessnassessscesesensesseens 17 El Port Assignment s scccsscsessssecceassescecsescecosacsecesssocscdasceacvasseacescsssceccaccsssaseseseassovscsseocssea 22 DISA Port Assignment 0ssscscesseescessssosssssncosssecssesessonessonsossatesesecsesessconsssonesenesesesasesessees 25 BRL Port Assignment ceiros sneseno aao s aae ra AAO N Ss ina ro a E RREO Rie RETOS 26 PRI Port ASSISTMENIE ear inro aaa E A EEEE EAE AS 28 Systemen AEE E TAS ATS DALE i i POE AEP EE A EAEE EE EEE EN 32 DOMAINE AAT T T E E EAEN 33 Numbering Plan ENE ER SENE EN OE AN A AA 39 Class of Service COS isssscceccesscsstecvevesectes ossvesosootesssssesseececesessessecessacetessoetseecnesesscsseostes 58 System TIMED is ccccctscssectacssedcucssedcssvecetccassesccacvecccacsseccacseodsecseecacdeseotcesssevccesssecdecseedcacsenceds 67 Local Hunt SQQuenCe s scccsseccccvsccscccsecsaccsecssceseces scostecscosssescostocsseusbesaccacesesesetescsensecssssseoss 76 Trunk to Trunk Restriction ccscsccccsssccsccsscccecsscscsccscesceesescerssssescscsssccessessesese 77 System Opti
205. stem detects a continuous signal during a CO to CO line call by DISA Reference e 1 5 Attended Features F G Direct Inward System Access DISA Group 3 2 Trunk Group Parameter Silence Detection Default Check Value Range 1 No check Disable 2 Check Enable Description Function Used to disconnect the trunk line if the system detects no signal during a CO to CO line call by DISA Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter Numbering Plan ID Outgoing Public Default Default Value Range 1 Default 2 Unknown 3 ISDN Telephony 4 National Standard 5 Private Description Function Specifies the Numbering Plan ID applied to the outgoing CO calls via ISDN Public Network Reference None Parameter Numbering Plan ID Outgoing Private Default Default Value Range 1 Default 2 Unknown 3 ISDN Telephony 4 National Standard 5 Private Description Function Specifies the Numbering Plan ID applied to the outgoing CO calls via ISDN Private Network Reference None 111 3 2 Trunk Group Parameter Numbering Plan ID Incoming Public Default Default Value Range 1 Default 2 Unknown 3 ISDN Telephony 4 National Standard 5 Private Description Function Specifies the Numbering Plan ID applied to the incoming CO calls via ISDN Public Network Reference None Parameter Numbering Plan ID Incoming Private Default Default V
206. t Follow on ID after IRNA Default Disable Value Range 1 Disable 2 Enable Description Function Specifies whether or not the system sends Follow on ID to a VPS port after redirecting a call IRNA to the VPS port Reference e 1 3 System Features F G Integration VPS Features 205 5 11 Caller ID Modification 5 11 Caller ID Modification Used to modify the telephone number sent from the Central Office by Caller ID Service to make up a telephone number for callback purposes 5 11 Caller ID Modification Local Call Area Code Digits to Number to Max 6 Digits delete be added 3 Le EN i i i TT m TUT Wi UU 5 o z 10 0 z Long Distance Call Digits to delete Humbertobeadded f 11 Caller ID Modification gt OK Apply Cancel Help Parameter Local Call Area Code Default Blank Value Range Up to 6 digits consisting of 0 9 Description Function Specifies the area code of the location where your KX TD500 system is installed Note e This local area code is referenced to modify the telephone number Reference 1 5 Attended Features F G Caller ID Service 206 Features 5 11 Caller ID Modification Parameter Local Call Digits to delete Default No 1 3 Others 0 Value Range 0 9 Description Function Specifies the number of digits to be deleted from the telephone number sent from the Central Office by Caller ID
207. te Cancel Help 3 Select the Extension Group parameters to copy in Copy Item field e Only parameters which are available to copy are shown in Copy Item field This depends on the Group Type assignment of the copy source Extension Group Items marked with W are copied 4 Point to the Select All button in the Destination Extension Group field and click e All displayed Extension Group Nos will be marked with W e You can also specify one or several Extension Groups as the copy destination by clicking it them directly 5 Point to the Execute button and click e Are you sure is displayed 6 Point to Yes Y button and click e Copying is displayed while the source data is being copied to the destination e Parameters of the destination Extension Groups are immediately effective when copying is finished Parameter Group No Default 1 Value Range 1 128 Description Function Specifies the Extension Group 1 128 which you are going to programme Reference e 1 3 System Features F G Extension Group Group 117 3 3 Extension Group Parameter FDN Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the FDN Floating Directory Number for the Extension Group Reference e 1 3 System Features F G Floating Station Parameter Group Type Default Group No 126 VM Group No 127 AA Group No 128 Operator Others None Value Range
208. tem field This depends on the attribute of the copy source Trunk Line e Items marked with W are copied 4 Point to the Select All button in the Destination Trunk Line field and click e All displayed Trunk Line Nos will be highlighted e You can also specify one or several Trunk Lines as the copy destination by clicking it them directly 5 Point to the Execute button and click e Are you sure is displayed 6 Point to Yes Y button and click e Copying is displayed while the source data is being copied to the destination e Parameters of the destination Trunk Lines are immediately effective when copying is finished Parameter Card No Default Value Range XXX YYY XXX Card No 101 314 YYY Card Type Description Function Specifies the physical number of the trunk card and its type which you are going to programme Reference 1 2 Slot Assignment P G 134 Line 4 2 Trunk Line Parameter Port No Default 1 Value Range 1 n n 4 E amp M n 16 BRD n 30 PRI30 n 31 El except Port No 16 n 8 Others Description Function Specifies the trunk port which you are going to programme Note e In some countries the El and the E amp M cards must not be connected to the Public Switched Network Reference 1 3 Trunk Port Assignment P G Parameter Group No Default Display only Value Range 1 48 Description Function Displays the Trunk Group to which the
209. ter the appropriate parameters Programming Example Base Number Dial 123456 Additional Number Number of Registrations 100 Additional Number Number of Digits 2 Beginning Entry No 1 3 Click Execute e The following DDI DID MSN numbers are registered in Entry Nos 1 100 of DDI DID MSN No automatically Programming Example DDI DID 243 9 2 Number Transformation Entry No 1 123456 00 Entry No 2 123456 01 Entry No 3 123456 02 Entry No 99 123456 98 Entry No 100 123456 99 Notes If more than 15 digits are entered in Base Number Dial field the following warning message will be displayed W9005 Base dial number must not exceed 15 digits Truncate it If you press OK the exceeded digits will be truncated automatically If the total digits of Base Number and Number of Digits are over 16 the following error message will be displayed E9010 Number of DDI dial must be equal to or less than 16 digits Then the operation will be aborted If Beginning Entry No exceeds 991 the following error message will be displayed E9011 Beginning Entry No must be equal to or less than 991 Then the operation is aborted The new entries will override the old ones if DDI DID MSN numbers are already registered in the specified areas If the number of remaining Entry fields is less than the number specified by Number of Registrations setting for example Nu
210. th a carriage return select CR Carriage Return If not select CR LF Line Feed Reference None Parameter Serial Interface Port SMDR Word Length Default 8 bits Value Range 1 7 bits 2 8 bits Description Function Defines the number of bits in each byte or character Reference None Maintenance 263 10 6 System Parameters Parameter Serial Interface Port SMDR Stop Bit Default 1 bit Value Range 1 1 bit 2 2 bits Description Function A stop bit code indicates the end of a bit string which composes a character Select an appropriate value depending on the requirements of your printer or personal computer Reference None Parameter Serial Interface Port SMDR Baud Rate Default 9600 bps Value Range 1 2400 bps 2 4800 bps 3 9600 bps 4 19200 bps Description Function Specifies the data transmission speed from the system to the printer or personal computer Reference None Parameter Remote FDN Default Blank Value Range Up to 4 digits consisting of 0 9 Description Function Specifies the FDN Floating Directory Number for Remote Administration Reference e 1 2 System Administration F G System Programming and Diagnosis with Personal Computer e 3 4 3 Remote Administration Remote Connection I M Maintenance 10 7 System Time 10 7 System Time Used to assign System Time Please refer to the following e 1 8 Ringing Features F G Timed Remi
211. ther or not you upload the language data after uploading the system data in off line mode If you click OK the Language Data Selection dialogue box is displayed and then uploading of the Language Data file can be executed W3001 PBX code must not exceed 4 digits Truncate it Truncate means that the leading 4 digits are saved and the rest are deleted W3002 Please verify that previously erased FDN is not programmed in other screens The erased FDN may be used in other screens w4001 Trunk name must not exceed 10 characters Truncate it Truncate means that the leading 10 characters are saved and the rest are deleted W4002 Extension name must not exceed 10 characters Truncate it Truncate means that the leading 10 characters are saved and the rest are deleted W4003 One Touch dial number must not exceed 24 digits Truncate it Truncate means that the leading 24 digits are saved and the rest are deleted W4004 CLIP COLP number must not exceed 16 digits Truncate it Truncate means that the leading 16 digits are saved and the rest are deleted 280 Programming Error Messages 11 2 Warning Messages WXXXX Message Code Description W4005 One Touch dial name must not exceed 10 characters Truncate it Truncate means that the leading 10 characters are saved and the rest are deleted W4006 DDI DID TIE additional dial must not exceed 8 digits Truncate it Truncate means that the
212. to which the BRI port is assigned Reference e 1 3 System Features F G Extension Group Trunk Group 32 Trunk Group P G 3 3 Extension Group P G Parameter Status Default Value Range 1 INS 2 OUS 3 FAULT Description Function Specifies the operating status of the BRI port 1 INS The BRI port is In Service 2 OUS The BRI port is Out of Service 3 FAULT The BRI port is defective hardware In this case the LED indicator on the BRI card will light Reference None Configuration 27 1 9 PRI Port Assignment 1 9 PRI Port Assignment Used to assign the parameters for PRI Prime Rate Interface ports 1 9 PRI Port Assignment Be ee Corano MJ tye oo Port Group Ho Status co m 3 2 ms 3 1 l INS 4 di ET Port DH Group Ho Tone Status if g oe Sala ok apply cancet Het Parameter Card No Default Value Range XXX PRI30 XXX Card No 101 314 Description Function Specifies the physical number of the PRI30 card which you are going to programme Reference e 1 2 Slot Assignment P G Parameter Type Default Display only Value Range CO fixed Description Function Displays the type of each PRI port fixed to CO CO line Reference e 2 1 ISDN Features F G Integrated Services Digital Network ISDN 28 Configuration 1 9 PRI Port Assignment Parameter Group No Default 1 Value Range 1 48 Des
213. uage Data file and click OK e Uploading of the Language Data from PC to the KX TD500 System begins e Uploading takes about 5 minutes lt System Programming gt When the uploading of the Language Data is finished 1 Go to 4 2 Extension Line screen and choose Option in Language menu 2 Click OK or Apply to save the data change Notes e The uploaded Language Data remains intact after the termination of system operation system reset e To clear the uploaded Language Data set the Operation Switch MODE to the position 5 and start up the system in off line mode 98 System 2 9 Language Data You can upload the Language Data after uploading the system data When system data upload is finished the Language Data Selection dialogue box is displayed Then you can upload the Language Data in the same way as described in lt Uploading the Language Data to the KX TD500 System gt System 99 2 9 Language Data 100 System Section 3 Group Group 101 3 1 Group 3 1 Group Used to assign various group parameters Rt TD500 Maintenance l Programming J u 102 Group 3 2 Trunk Group 32 Trunk Group Used to assign parameters for each trunk group 3 1 Trunk Group Se Grou no me em Intercept Destination _ _ _ _ Pause Time before Flash M
214. ult 10 s SP NL JT 5 s G Value Range 5 120 s Description Function Specifies the maximum time allowed between the start of an outside dial tone and the first digit dialled on an outgoing call Reference None Parameter Inter digit Time Default 5s Value Range 1 30 s Description Function Specifies the maximum time allowed between each digit on an outgoing call Note e This timer applies to the call until the Toll Restriction check is completed Reference None Parameter Intercept Time Default 12 rings Value Range 1 48 rings Description Function Specifies the number of rings the system is to wait before activating IRNA Intercept Routing No Answer feature If an incoming CO call directed to a single extension is not answered within this timer IRNA redirects the call to another pre programmed destination Note e Call Forwarding No Answer Time will override this timer if an extension has enabled Call Forwarding No Answer Reference e 1 11 Transferring Features F G Intercept Routing 69 2 5 System Timer Parameter Call Forwarding No Answer Time Default 3 rings Value Range 1 12 rings Description Function Specifies the number of rings before the Call Forwarding No Answer feature is activated If a call is not answered before the programmed number of rings the call is redirected to the pre assigned extension Note e This timer is also used for Intercept Routing If an incoming DISA c
215. ult Own Extension Value Range 1 Own Extension 2 PDN Description Function This setting is applied when an extension user makes an outside call using an SDN button on his or her own extension 1 Own Extension COS TRS level of his her own applies when making an outside call using the SDN button 2 PDN COS TRS level of the owner extension applies when making an outside call using the SDN button Assignable for a DN type PT user only Reference e 4 1 2 Customising the Buttons U M Parameter Off Hook Call Announcement OHCA Default Enable Value Range 1 Enable 2 Disable Description Function Specifies whether to utilise OHCA Whisper OHCA feature or not Note e This setting is valid at the following PT extensions KX T7130 KX T7235 KX T7536 Reference e 1 6 Originating Features F G Off Hook Call Announcement OHCA Off Hook Call Announcement OHCA Whisper e 2 7 3 Receiving a Call Waiting Call Waiting Off Hook Call Announcement OHCA Whisper OHCA U M System 63 2 4 Class of Service COS Parameter Released Link Operation Default Disable Value Range 1 Enable 2 Disable Description Function Used to turn on off Released Link Operation mode of the extension When Released Link Operation is enabled an extension user will be automatically released from a call extension outside after transferring it to the destination ifthe destination extension is idle This feature si
216. umber Reference e 1 6 Originating Features F G Automatic Route Selection ARS 232 ARS Automatic Route Selection 7 5 Digits Modification Table Parameter Number to be added Default Blank Value Range Up to 20 digits consisting of 0 9 or P Pause Description Function Specifies the dialling number to be added to the beginning of the user dialled number Reference e 1 6 Originating Features F G Automatic Route Selection ARS ARS Automatic Route Selection 233 7 5 Digits Modification Table 234 ARS Automatic Route Selection Section 8 Private Network Private Network 235 8 1 Private Network 8 1 Private Network Used to assign parameters required to utilise TIE line service 236 Private Network 82 TIE Routing Table 82 TIE Routing Table Used to specify trunk groups and parameters required for making TIE calls This table is referenced by the system to identify the trunk route when an extension user made a TIE call by dialling the feature number for TIE Line Access or Other PBX Extension number The first 3 digits other than TIE Line Access Code of the dialled number decide a routing pattern appropriate for each call Up to 36 routing patterns can be programmed in this table 8 1 TIE Routing Table Entry No mo PBX Code Max 3 Digits E Max 3 Digits delete ak Leading Digit Digits to
217. unction A stop bit code indicates the end of a bit string which composes a character Select an appropriate value depending on the requirements of your printer or personal computer Note e Port 1 is fixed to 1 bit Reference None Parameter Serial Interface Port PROG Baud Rate Default 19200 bps Value Range 1 2400 bps 2 4800 bps 3 9600 bps 4 19200 bps Description Function Specifies the data transmission speed from the system to the printer or personal computer Reference None of the Features Guide Note Serial Interface Port SMDR Port 2 Please refer to Station Message Detail Recording SMDR in Section 1 3 System Features e Generally speaking you should connect your Programming PC to Port 1 and your SMDR printer to Port 2 262 Maintenance 10 6 System Parameters Parameter Serial Interface Port SMDR Parity Default None Value Range 1 None 2 Mark 3 Space 4 Even 5 Odd Description Function A parity code indicates what type of parity is used to detect an error in the string of bits composing a character Make an appropriate selection depending on the requirements of your printer or personal computer Reference None Parameter Serial Interface Port SMDR NL Code Default CR LF Value Range 1 CR LF 2 CR Description Function Specifies the NL New Line Code for your printer or personal computer If your printer or personal computer automatically feeds lines wi
218. up Dialling Timed Reminder Also enabled is Dial Tone 4 indicates that messages are waiting Note e Dial Tone 3 is not affected by this setting e 5 4 What is This Tone U M Parameter 16 Duration starting mode Default Value Range Description Function Reference Answer or Time out 1 Answer or Time out 2 Answer Specifies the call duration count start timing None 84 System 2 8 System Option Parameter 17 Destination Busy DISA Default Send busy tone Value Range 1 Send busy tone 2 Transferred to IRNA destination Description Function Specifies the treatment of DISA callers when they dial a busy extension Reference e 1 5 Attended Features F G Direct Inward System Access DISA Parameter 18 Destination Busy DDI DID Default Send busy tone Value Range 1 Send busy tone 2 Transferred to IRNA destination Description Function Specifies the treatment of DDI DID callers when they dial a busy extension Reference e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDI Parameter 19 Destination Busy TIE Default Send busy tone Value Range 1 Send busy tone 2 Transferred to IRNA destination Description Function Specifies the treatment of TIE callers when they dial a busy extension Reference 3 1 E amp M Features F G E amp M TIE Line Service 85 2 8 System Option
219. urce trunk group Reference 3 1 E amp M Features F G E amp M TIE Line Service System 77 2 8 System Option 2 8 System Option 2 8 1 System Option 1 4 Used to assign system option parameters No 1 No 10 2 7 System Option 1 4 BEE 1 Sound source during transfer _ 6 Transfer recall destination Ringback Tone Music on Hold Originating extension Operator 2 SLT On hook with consulting held call 7 Checking dial by toll restriction Consulting Hold C Disconnect CWocheck Check 3 FLASH button operation while CO talking 8 Confirmation tone for Override Barge in Conference and Privacy Release Release the trunk C Don t release the trunk Enable C Disable 4 FLASH button operation when _______ 9 Confirmation tone for Call Pickup Don t release the trunk is selected at 3 Paging Answer TAFAS Answer Hold Disconnect and hear CO dial tone Bete ot Con Ea Ree Sending EFA signal Enable C Disable _ 5 Limited call duration 10 Station Speed Dialing Initial display C Outgoing call only Both calls Name C Humber ox amy cones uep Parameter 1 Sound source during transfer Default Music on Hold Value Range 1 Ringback Tone 2 Music on Hold Description Function Used to determine whether the system sends Music on Hold or Ringback Tone to the party being transferred Ringback Tone is available when Mus
220. ures F G Caller ID Service Parameter Print out DDI DID subscriber number Default Disable Value Range 1 Disable 2 Enable Description Function Activates or deactivates printing out the DDI DID subscriber number received from the Central Office Reference e 1 5 Attended Features F G Direct Inward Dialling DID e 2 4 ISDN Attended Features F G Direct Dialling In DDI Parameter Print out Incoming Call Start RC and Incoming Call Answer AN information Default Disable Value Range 1 Enable 2 Disable Description Function Enables or disables the SMDR printout for RC when an incoming call occurs and AN when an incoming call is answered Reference None Maintenance 255 10 4 SMDR Parameter Print out No Answer of Timed Reminder information Default Disable Value Range 1 Enable 2 Disable Description Function If this is enabled SMDR will print out Timed Reminder Start each time the timed reminder alarm starts ringing In addition if the ringing is not stopped by going off hook the SMDR will print out Timed Reminder No Answer Reference e 1 8 Ringing Features F G Timed Reminder Wake Up Call Timed Reminder Remote Wake Up Call Parameter Print out Account Code Default Enable Value Range 1 Enable 2 Disable Description Function Specifies whether or not the Account Code will be printed out by SMDR Reference e 1 3 System Features F G Account Code Entry Parameter
221. when an AA port lights the MESSAGE indicator This command is also transmitted preceding the Leave Message command if Operator transfers a call to an extension and then it is forwarded to an AA port so that the AA port can be switched to VM port temporarily Reference e 1 3 System Features F G Integration VPS 5 10 2 VPS Integration 2 2 Used to assign optional parameters for VPS Integration Features 201 5 10 VPS Integration 5 10 VPS Integration 2 2 lei Ea DTMF signal duration 80 ms C 160 ms Pause timing before sending DTMF signal Follow on ID C05s C41 0s C15s C 20s Pause timing before sending DTMF signal RBT BT C 05s C41 0s C15s C 20s r Turn off control of Message Waiting lamp _ Call from AA port to AA port System Voice Mail Allow C Deny Start AA service after FWD IRNA of CO call Do not start C Start f Disable Enable r Sending out Follow on ID after FWD Extension s mailbox number C Extension number Programmed number Disable C Enable r Sending out Follow on ID after IRHA ox amy comeu uep Parameter DTMF signal duration Default 80 ms Value Range 1 80 ms 2 160 ms Description Function Specifies the duration of the DTMF signals sent to the VPS Voice Processing System ports Reference 1 3 System Features F G Integration VPS Parameter Pause timing before sendin
222. you are going to programme Reference 1 2 Slot Assignment P G Parameter Port No Default 1 Value Range 1 4 Description Function Specifies the doorphone port which you are going to programme Reference None 174 Line 4 5 Doorphone Parameter Tenant No Default 1 Value Range 1 8 Description Function Specifies the tenant number to which the doorphone port is assigned Reference e 1 3 System Features F G Tenant Service e 1 12 Conversation Features F G Doorphone Call 2 2 Tenant P G Parameter Destination Day Night Default Blank Value Range 3 4 digits consisting of 0 9 Description Function Specifies the extensions that ring when a visitor presses the doorphone button Up to 126 destination extensions per doorphone can be assigned in Day mode and Night mode respectively Destination extensions can unlock the door opener Reference 2 8 1 If a Doorphone Door Opener is Connected U M Line 175 4 6 External Paging 4 6 External Paging Used to assign parameters for External Paging 4 5 External Paging sul a ew Parameter Pager No Default Display only Value Range 1 2 Description Function Displays the Pager No Reference 2 8 2 External Pager Paging Equipment I M Parameter Tenant No Default 1 Value Range 1 8 Description Function Specifies the tenant to which the External Pager is assigned Required when Tenant Service is em
Download Pdf Manuals
Related Search
Related Contents
Swann MEGA FLOOD SW-C-MFC User's Manual Manifeste de Michel Dubois Internet FR 1[...] HG "polish pour faire briller le cuivre" MANUAL DE MONTAJE / MANUAL DEL USUARIO Este 川口市緊急通報システム Web119 から送るメールは WASHER VE 1449 A++ AOSafety 2-Way User's Manual manuale tecnico SE200 User`s Manual PDF 515 ko Copyright © All rights reserved.
Failed to retrieve file