Inno Beam LED User Manual - ProSound and Stage Lighting
Contents
1. 3 15 DJ N INNO BEAM LED I 0000 Y I User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disc2. No will be displayed 2 To activate the Tilt inversion press the UP or DOWN buttons until Yes is displayed press ENTER to confim To deactivate Tilt inversion select No and press Enter Back Light With this function you can make the back light automatically turn off after one minute 1 Press the MENU button until Back Light is displayed press ENTER 2 Either ON or OFF will now be displayed Press the UP or DOWN buttons to select ON to keep the backlight on at all times or OFF to allow the backlight to turn off after 2 minutes Press any button to turn the backlight on again 3 Press ENTER to confirm Dimmer Calibrat with this function you can set the output intensity 1 Press the MENU button until Dimmer Calibrat is displayed press ENTER 2 Anumber between 50 100 will be displayed This number rep ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 15 Inno Beam LED System Menu resents the instensity setting Use the UP or DOWN buttons to adjust the LED output intensity 50 being medium intensity and 100 being full intensity 3 When you have found your desired setting press ENTER to confirm Auto Test This function will run a self test program 1 Press the MENU button until Auto Test is displayed press ENTER 2 The fixture will now run a self test Press the MENU button to exit Fixture Temp With this function yo
3. Periodic cleaning will ensure longevity and crisp output 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing 2 Use a brush to wipe down the cooling vents and fan grill 3 Clean the external optics with glass cleaner and a soft cloth every 20 days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in Inno Beam LED Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions No light output from the unit 1 Be sure you have connected your unit into a standard 120v wall outlet Be sure to voltage selector switch in the correct position Be sure the external fuse has not blown The fuse is located on the rear panel of the unit 3 Be sure the fuse holder is completely and properly seated N Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 29 Inno Beam LED Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty
4. 28 YELLOW FAST SLOW 29 35 GREEN aa SE 190 193 STOP 194 255 CLOCKWISE ROTATION SLOW FAST 43 49 MAGENTA ASARIN 50 56 LIGHT BLUE 0 7 OFF 57 63 PINK a baie 64 127 SPLIT COLORS f 128 189 RAINBOW EFFECT FAST SLOW 16 131 STROBING SLOW FAST ae eae 132 139 OPEN 194 255 RAINBOW EFFECT SLOW FAST 140 181 SLOW OPEN FAST CLOSE GOBO WHEEL CONT 182 189 OPEN 190 231 FAST OPEN SLOW CLOSE 232 239 OPEN 240 247 RANDOM STROBE 248 255 OPEN GOBO WHEEL 0 7 OPEN 8 15 GOBO 1 16 23 GOBO 2 24 31 GOBO 3 32 39 GOBO 4 40 47 GOBO 5 48 55 GOBO 6 56 63 GOBO 7 64 71 OPEN SHAKE 2 79 GOBO 1 SHAKE 80 87 GOBO 2 SHAKE 88 95 GOBO 3 SHAKE 96 103 GOBO 4 SHAKE 104 111 GOBO 5 SHAKE 112 119 GOBO 6 SHAKE 120 127 GOBO 7 SHAKE 128 189 GOBO WHEEL ROTATION FAST SLOW BLACKOUT RESET NOTHING ENABLE BLACKOUT W PAN TILT MOVEMENT DISABLE BLACKOUT W PAN TILT MOVEMENT ENABLE BLACKOUT W COLOR CHANGE DISABLE BLACKOUT W COLOR CHANGE ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 25 ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 26 Inno Beam LED 14 Channel Mode Inno Beam LED Function 13 Photometric Chart BLAGKOUT RESET LUX 159000 75300 40060 19930 14470 9800 110 119 ENABLE BLACKOUT W GOBO ee a a a a SS5 om Ss CHANGE _ 120 199 DISABLE portend W GOBO neta T T 30 re a
5. fixture is between 25 C to 45 C Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above This will allow the fixture to run at its best and help prolong the fixture life Screw one clamp via a M12 screw and nut onto the Omega holder Insert the quick lock fasteners of the Omega holder into the respective holes on the bottom of the Inno Beam LED Tighten the quick lock fasteners fully clockwise Pull the safety cable through the hole on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 7 Inno Beam LED Set Up Power Supply The ADJ Inno Beam LED contains a automatic volt age switch which will auto sense the voltage when it is plugged into a power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals loca
6. period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the pro duct only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instru ment is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC
7. then press ENTER to confirm Press the MENU button for one second to exit Prism Offset Home setting adjustment for the prism 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Prism Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit RPrism Offset Home setting adjustment for the rotat ing prism 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that RPrism Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit Frost Offset Home setting adjustment for the frost 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Frost Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 19 Inno Beam LED Operation Operating Modes Sound Active mode The fixture will react to sound chasing through the built in programs e Show mode The fixture will run one of four shows that you choose e DMX control mode This function will allow you to control each individual fixtures t
8. 4 DMX Channels 8 White 4 4 Spots Sound Active Yes Working Position Warranty Any Safe Secure Position 2 Year 730 days Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 31 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Follow Us On FPR Netherlands iaesenoh con amerieana service adjgroup eu www adj eu youtubecom adjiighting Tel 31 45 546 85 00 Fax 31 45 546 85 99
9. ROTATION 360 PRISM INDEXING 128 189 COUNTER CLOCKWISE ROTATION FAST SLOW 190 193 STOP 194 255 CLOCKWISE ROTATION SLOW FAST 132 139 OPEN 140 181 SLOW OPEN FAST CLOSE 182 189 OPEN 190 231 FAST OPEN SLOW CLOSE 232 239 OPEN 240 247 RANDOM STROBE 248 255 OPEN 7 SHUTTER 0 7 OFF 8 15 OPEN 16 131 STROBING SLOW FAST 12 Channel Mode Inno Beam LED 12 Channel Mode Function 11 BLACKOUT RESET 200 209 RESET ALL 210 255 NOTHING 12 DIMMER MODES 0 20 STANDARD 21 40 STAGE 41 60 TV 61 80 ARCHITECTURAL 81 100 THEATRE 101 255 UNIT DEFAULT To disable blackouts under channel 11 set the fader to the according blackout values and wait 3 seconds BLACKOUT RESET NOTHING ENABLE BLACKOUT W PAN TILT MOVEMENT DISABLE BLACKOUT W PAN TILT MOVEMENT ENABLE BLACKOUT W COLOR CHANGE 100 109 DISABLE BLACKOUT W COLOR CHANGE 110 119 ENABLE BLACKOUT W GOBO CHANGE 120 199 DISABLE BLACKOUT W GOBO CHANGE ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 23 ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 24 Inno Beam LED 14 Channel Mode Inno Beam LED 14 Channel Mode Value Function Function 0 255 PAN STOP ame PAN TINE GOBO WHEEL ROTATION SLOW FAST gt Sia PRISM EFFECT 4 0 255 TILT FINE NT NO EFFECT PEN PRISM EFFECT ae iis PRISM ROTATION ae BENGE 360 PRISM INDEXING 428 189 COUNTER CLOCKWISE ROTATION 29
10. Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable G X to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 9 Inno Beam LED Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal Pin 3 Inno Beam LED Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 3 fixtures maximum for 120V and 6 fixtures maxi mum for 240V After the maximum fixtures has been reached you will need to use a new power outlet They must be the same fix tures DO NOT mix fixtures ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 10 Inno Beam LED System Menu 001 DMX Address 512 12 Chan Channel Mode 14 Chan Show 1 Show 2 Sh
11. a 200 209 RESET ALL i 210 255 NOTHING Inno Beam LED Dimmer Curve Chart DIMMER MODES Dimmer STANDARD STAGE TV 100 ARCHITECTURAL THEATRE UNIT DEFAULT 50 To disable blackouts under channel 13 set the fader to the according blackout values and wait 3 seconds 10 0 m L T Ta ms a o 7 0S Fade Time _ 18 Fade Time Trise ms Todown ms Trise ms Taown ms Standard 0 0 0 0 Stage 780 1100 1540 1660 TV 1180 1520 1860 1940 Architectural 1380 1730 2040 2120 Theatre 1580 1940 2230 2280 ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 27 ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 28 Inno Beam LED Fuse Replacement Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse Inno Beam LED Cleaning Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environ ment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis
12. e UP or DOWN buttons to find your desired address 3 Press ENTER to confirm and then press and hold the MENU button for at least three seconds to assign Channel Mode This will let you select your desired DMX Channel mode 1 Press the MENU button until Channel Mode is displayed press ENTER 2 X Chan will now be displayed X represents the displayed DMX channel mode either 12 Channel Mode or 14 Channel Mode Press the UP or DOWN buttons to find your desired Chan nel mode 3 Press ENTER to confirm Show Mode Show modes 1 4 Factory Shows 1 Press the MENU button until Show Mode is displayed press ENTER ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 12 Inno Beam LED System Menu 2 Show X will now be displayed X representing a number between 1 4 Press the UP or DOWN buttons to find your desired show and press ENTER to confirm 3 Press and hold the MENU button for at least 3 seconds to activate Dimmer Mode In this mode you can select the dimmer curve See page 26 for the different dimmer modes 1 Press the MENU button until Dimmer Mode is displayed press ENTER 2 The current dimmer mode will be displayed 3 Press the UP or DOWN buttons to find your desired dimmer mode and press ENTER to confirm Slave Mode This will let you set unit as a master or slave in a master slave configuration 1 Press the MENU button until S
13. fter said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LEDs and lamps e Laser Products 90 Day Limited Warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 30 Inno Beam LED Specifications Inno Beam LED 100 240V 50 60Hz 1 x 80W LED Power Consumption 129W Power Cord Daisy Chain 3 Fixtures Max 120V 6 Fixtures Max 240V 11 5 L x 7 5 W x 18 25 H 289mm x 188mm x 461mm 6 Degrees Dimensions Beam Angle 18 Lbs 8 2 kgs 7 Amp None 12 DMX Channels amp 1
14. ggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail supportQ Qamericandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all times ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 2 Inno Beam LED General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Inno Beam LED Features e DMX 512 Protocol Compatible e 2 DMX Modes 12 Channel Mode amp 14 Channel Mode 8 Colors White 4 Fixed Gobos amp 4 Spots 3 Operating Modes Sound Active Show Mode amp DMX Control Digital Display for Address and Function Setting UC3 Control Controller Not Included 4 Preprogrammed Shows Power Cord Daisy Chain See page 10 Inno Beam LED Warranty Registration The Inno Beam LED carries a 2 year 730 days limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www adj products com All
15. if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product a
16. ional sound and lighting stores Your cables should be made with Figure 1 ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 8 Inno Beam LED T MO a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 r l l XLR Male Socket ALR Female Sockel 1 XLR Pin Configuration l l 1 1 Ground 1 2 Cold 2 Cold 1 Ground Pin 1 Ground Pin 2 Data Compliment negative l l I I l l Pin 3 Data True positive Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior
17. ked change in performance ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 5 Inno Beam LED Mounting When installing the unit the trussing or area of installation must be able to hold 10 times the weight without any deformation When installing the unit must be secured with a secondary safety attach ment e g and appropriate safety cable Never stand directly below the unit when mounting removing or servicing the unit Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself The installaiton should be checked by a skilled person once a year ey The Inno Beam LED is fully operational in two different mounting positions hanging upside down from a ceiling or set on a flat level surface To avoid internal damage to the unit never mount the unit on its side as illustrated above Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails See next page ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 6 Inno Beam LED Mounting NOTICE The suitable enviromental temperature for this light ing
18. lave Mode is displayed press ENTER Either Slave 1 or Slave 2 will be displayed 2 Press the UP or DOWN buttons until your desired slave mode is displayed press ENTER to confim NOTE In a Master Slave configuration you can make one fixture the Master and then set the next fixture to Slave 2 the fixtures will now have contrast movement to each other No DMX This mode can be used as a precaution mode that in case the DMX signal is lost interrupted or power is lost the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost You can also set this as the operating mode you would like the unit to return to when power is applied 1 Press the MENU button until NO DMX is displayed and ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 13 Inno Beam LED System Menu either Show Blackout or Hold will be displayed beneath 2 Press ENTER and the bottom choice will begin to flash Use the UP or DOWN buttons to choose an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost e Show If the DMX signal is lost or interrupted the unit will automatically go into the last selected show mode e Blackout If the DMX signal is lost or interrupted the unit will automatically go into stand by mode Hold If the DMX signal is lost or interrupted the fixture will sta
19. onnect all electrical equipment from power when not in use Thank you Inno Beam LED General Information Unpacking Thank you for purchasing the Inno Beam LED by ADJ Products LLC Every Inno Beam LED has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for fur ther instructions Please do not return this unit to your dealer without contacting customer support first Introduction The Inno Beam LED is a 13 channel DMX intelligent moving head LED fixture The Inno Beam LED can operate as a stand alone fixture or in a Master Slave configuration The Inno Beam LED has three operating modes a sound active show mode DMX con trolled This fixture is suitable for theaters studios retail stores and other similar locations For best results use fog or special effects smoke to enhance the beams projections Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or su
20. ow 3 Show 4 Standard Stage TV Architec Show Mode Dimmer Mode Theatre Slave 1 MENU Slave Mode Slave 2 Show Blackout Hold on A a a No DMX Sound State off 0 Sound Sense Pan Invert Tilt Invert Back Light Dimmer Calibrat Lo ob ei Auto Test Fixture Temp Fixture Time irmware Version Reset ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 11 Inno Beam LED System Menu System Menu When making adjustments you can press ENTER to confirm your setup then press and hold the MENU button for at least 3 seconds to lock it in or you can wait 8 seconds for automatic setup To exit without making any adjustments press the MENU button CONTROL PANEL LOCK The control panel will lock itself after 30 seconds if noth ing is pressed To unlock the control panel press the MENU button for 3 seconds DMX Address Set the DMX Address 1 Press the MENU button until DMX Addresss is displayed press ENTER 2 X will now be displayed X represents the displayed address Press th
21. raits with a standard DMX 512 controller such as the Elatione Show Designer Universal DMX Control This function allows you to use a Elatione universal DMX 512 controller to control the chases and patterns dimmer and strobe A DMX controller allows you to create unique programs tailored to your individual needs 1 The Inno Beam LED has 2 DMX modes a 12 channel mode and 14 channel mode See pages 22 27 for detailed description of the DMX values and traits 2 To control your fixture in DMX mode follow the set up procedures on pages 8 10 as well as the set up specifications that are includ ed with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the instructions on page 12 to set the DMX address For longer cable runs more than a 100 feet use a terminator on the last fixture For help operating in DMX mode consult the manual included with your DMX controller Ot ge pa N Sound Active Mode This mode allows either single unit or several units linked together to run to the beat of the music 1 Press the MENU button until Sound State is displayed and press ENTER Press the UP or DOWN buttons so that ON is displayed and press ENTER 2 The sound sensitivity can be adjusted by pressing the MENU button until Sound Sense is displayed Press ENTER and use the UP and DOWN buttons to adjust the sound sensiti
22. returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ Products LLC customer support for a R A number Inno Beam LED Handling Precautions Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC During operation the housing may become extremely hot Avoid touching the unit with bare hands while in use ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 3 Inno Beam LED Safety Precautions For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from
23. rtain functions Pan Offset Adjustment of the pan home position 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Pan Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit Tilt Offset Adjustment of the tilt home position 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Tilt Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit Color Offset Home setting adjustment for the color wheel 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Color Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 18 Inno Beam LED Home Adjustment Menu then press ENTER to confirm Press the MENU button for one second to exit Gobo Offset Home setting adjustment for the gobo wheel 1 Press the ENTER button for at least 3 seconds then press the UP or DOWN buttons so that Gobo Offset is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and
24. slave units tap the MENU button until Slave Mode is displayed and Press ENTER Choose either Slave 1 or Slave 2 and press ENTER See pages 13 14 for more info 4 The slave units will now follow the Master unit UC3 Control The optional UC3 Controller not included may be used to con trol different functions including blackout Stand By Blackout the unit Function 1 Sync Strobe Show 1 Press to select color 2 Async strobe 1 4 2 Hold to select gobo 3 Sound Strobe Inno Beam LED Sound LED OFF Show LED Slow Blinking ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 21 Value 128 189 190 193 194 255 8 15 16 23 24 31 32 39 40 47 48 55 56 63 64 71 12 19 80 87 88 95 96 103 104 111 112 119 120 127 128 189 190 193 194 255 Inno Beam LED 12 Channel Mode Function PAN TILT COLORS OPEN RED ORANGE YELLOW GREEN BLUE MAGENTA LIGHT BLUE PINK SPLIT COLORS RAINBOW EFFECT FAST SLOW STOP RAINBOW EFFECT SLOW FAST GOBO WHEEL OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6 GOBO 7 OPEN SHAKE GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE GOBO 5 SHAKE GOBO 6 SHAKE GOBO 7 SHAKE GOBO WHEEL ROTATION FAST SLOW STOP GOBO WHEEL ROTATION SLOW FAST ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 22 Inno Beam LED Function 5 PRISM EFFECT NO EFFECT PRISM EFFECT PRISM
25. ted on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant Jo ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Inno Beam LED can be controlled via DMX 512 pro tocol The Inno Beam LED has 2 DMX modes The DMX address is set electronically using the controls on the front panel of the unit Your unit and your DMX control ler require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all profess
26. the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 28 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fallen or liquid has been spilled into the appliance B The appliance has been exposed to rain or water C The appliance does not appear to operate normally or exhibits a mar
27. u can display the running temperature of the unit 1 Press the MENU button until Fixture Temp is displayed press ENTER 2 The current running temperature of the fixture will now be displayed Press MENU to exit Fixture Time With this function you can display the running time of the unit 1 Press the MENU button until Fixture Time is displayed press ENTER 2 The running time of the fixture will now be displayed Press MENU to exit Firmware Version This will display the software ver sion 1 Press the MENU button until Firmware Version is displayed Press the ENTER button and the software vesion will be dis played ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 16 Inno Beam LED System Menu 2 Press the MENU button to leave this function Reset Use this function to reset the motors 1 Tap the MENU button until Reset is displayed press ENTER 2 The fixture will now reset the motors ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 17 Inno Beam LED Home Adjustment Menu Pan Offset 127 127 Tilt Offset 127 127 Color Offset 127 127 Gobo Offset 127 127 Prism Offset _0 255 RPrism Offset 127 127 Frost Offset 0 255 To enter the home adjustment submenu press the ENTER button for at least 5 seconds In this submenu you are able to adjust the original position home position of ce
28. vity 0 being the least sensitive and 100 being the most 3 The optional UC3 Controller not included may be used to con trol different functions including blackout ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 20 Inno Beam LED Operation Show Mode This mode allows either a single unit or several units linked together to run one of four shows that you choose 1 Press the MENU button until Show Mode is displayed and press ENTER 2 Press the UP or DOWN buttons until you find your desired show and press ENTER Inno Beam LED Master Slave Setup Master Slave Configuration This function will allow you to link up to 16 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units pro grams Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units togeth er via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a termina tor at the last fixture 2 On the Master unit find your desired show and set that show by pressing the ENTER button 3 On the
29. y in the last DMX setting If power is applied and this mode is set the unit will automatically go into the last DMX set up 3 Press ENTER to confirm your desired set up Sound State In this mode the unit will run in sound active mode 1 Press the MENU button until Sound State is displayed press ENTER 2 Either On or Off will now be displayed Use the UP or DOWN buttons to toggle between On and Off 3 Press ENTER to confirm your selection the press and hold the MENU button to activate Sound Sense tn this mode you can adjust the sound sensitivity of the sound active mode 1 Press the MENU button until Sound Sense is displayed press ENTER 2 Press the UP or DOWN buttons to adjust the sensitivity level The sensitivity level can be adjusted between 0 the lowest and 100 most sensitive ADJ Products LLC www adj com Inno Beam LED Instruction Manual Page 14 Inno Beam LED System Menu 3 Press ENTER to set you desired level Pan Invert Pan Inversion 1 Press the MENU button until Pan Invert is displayed press ENTER Either Yes or No will be displayed 2 To activate the Pan inversion press the UP or DOWN buttons until Yes is displayed press ENTER to confim To deactivate Pan inversion select No and press Enter Tilt Invert Tilt Inversion 1 Press the MENU button until Tilt Invert is displayed press ENTER Either Yes or
Download Pdf Manuals
Related Search