SuperH Family E10A-USB Emulator Additional Document for Users
Contents
1. Family El0A USB Emulator User s Manual VccQ 3 3 V I O power supply Pulled up at 4 7 kQ or more all VecQ VccQ VccQ VccQ H UDI port connector 14 pin type SH7606 User system Figure 1 2 Recommended Circuit for Connection between the H UDI Port Connector and MPU when the Emulator is in Use ENESAS ENESAS Section 2 Specifications of the Software when Using the SH7606 2 1 Differences between the SH7606 and the Emulator 1 When the emulator system is initiated it initializes the general registers and part of the control registers as shown in table 2 1 The initial values of the actual SH7606 registers are undefined When the emulator is initiated from the workspace a value to be entered is saved in a session Table 2 1 Register Initial Values at Emulator Link Up Register Emulator at Link Up RO to R14 H 00000000 R15 SP SP in the vector address PC PC in the vector address SR H 000000F0 GBR H 00000000 VBR H 00000000 MACH H 00000000 MACL H 00000000 PR H 00000000 2 The emulator uses the H UDI do not access the H UDI 3 Low Power States Sleep and Standby For low power consumption the SH7606 has sleep and standby states The sleep and standby states are switched using the SLEEP instruction When the emulator is used only the sleep state can be cleared with either the normal clearing function or with the STOP button and a break will occur Note The memory must not b2. Table 2 3 Types of Break Conditions Break Condition Type Address bus condition Address Description Breaks when the SH7606 address bus value or the program counter value matches the specified value Data bus condition Data Breaks when the SH7606 data bus value matches the specified value Byte word or longword can be specified as the access data size Bus state condition Bus State There are two bus state condition settings Read Write condition Breaks when the SH7606 RD or RDWR signal level matches the specified condition Bus state condition Breaks when the operating state in an SH7606 bus cycle matches the specified condition Types of buses that can be specified are listed below e L bus CPU ALL Indicates an instruction fetch and data access including a hit to the cache memory e L bus CPU Data Indicates a data access by the CPU including a hit to the cache memory e bus CPU DMA Indicates a CPU cycle when the cache memory is not hit and a data access by the DMA Internal I O break condition Breaks when the SH7606 accesses the internal I O Count Breaks when the conditions set are satisfied the specified number of times Note When U RAM is accessed from the PO space the I bus must be selected and when accessed from the P2 space the L bus must be selected When cache fill cycle is acquired the I bus must be selected 11 ENESAS Table 2 4 lists the combination
3. When execution resumes from the address where aBREAKPOINT is specified single step operation is performed at the address and execution is continued from the next PC value Therefore realtime operation cannot be performed 6 When a BREAKPOINT is set to the slot instruction of a delayed branch instruction the PC value becomes an illegal value Accordingly do not set a BREAKPOINT to the slot instruction of a delayed branch instruction 7 When a BREAKPOINT is set to the cacheable area the cache block containing the BREAKPOINT address is filled immediately before and after user program execution ENESAS 8 If an address of a BREAKPOINT cannot be correctly set in the ROM or flash memory area a mark will be displayed in the BP area of the address on the Editor or Disassembly window by refreshing the Memory window etc after Go execution However no break will occur at this address When the program halts with the break condition the mark disappears 2 2 5 Notes on Setting the Break Condition Dialog Box and BREAKCONDITION_SET Command 1 When Go to cursor Step In Step Over or Step Out is selected the settings of Break Condition 2 are disabled 2 Break Condition 2 is disabled when an instruction to which a BREAKPOINT has been set is executed Accordingly do not seta BREAKPOINT to an instruction which satisfies Break Condition 2 3 When a Break Condition is satisfied emulation may stop after two or more instruc
4. LES OFFICES Refer to http www renesas com en network for the latest and detailed information http www renesas com Renesas Technology America Inc 450 Holger Way San Jose CA 95134 1368 U S A Tel lt 1 gt 408 382 7500 Fax lt 1 gt 408 382 7501 Renesas Technology Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5FH United Kingdom Tel lt 44 gt 1628 585 100 Fax lt 44 gt 1628 585 900 Renesas Technology Shanghai Co Lid Unit2607 Ruijing Building No 205 Maoming Road S Shanghai 200020 China Tel lt 86 gt 21 6472 1001 Fax lt 86 gt 21 6415 2952 Renesas Technology Hong Kong Lid 7th Floor North Tower World Finance Centre Harbour City 1 Canton Road Tsimshatsui Kowloon Hong Kong Tel lt 852 gt 2265 6688 Fax lt 852 gt 2730 6071 Renesas Technology Taiwan Co Ltd 10th Floor No 99 Fushing North Road Taipei Taiwan Tel lt 886 gt 2 2715 2888 Fax lt 886 gt 2 2713 2999 Renesas Technology Singapore Pte Lid 1 Harbour Front Avenue 06 10 Keppel Bay Tower Singapore 098632 Tel lt 65 gt 6213 0200 Fax lt 65 gt 6278 8001 Renesas Technology Korea Co Ltd Kukje Center Bldg 18th FI 191 2 ka Hangang ro Yongsan ku Seoul 140 702 Korea Tel lt 82 gt 2 796 3115 Fax lt 82 gt 2 796 2145 Renesas Technology Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 Jalan Persiaran Barat 46050 Petaling Jaya Selan
5. O registers can be accessed from the IO window After the I O register definition file is created the MPU s specification may be changed If each I O register in the I O register definition file differs from addresses described in the hardware manual change the I O register definition file according to the description in the hardware manual The VO register definition file can be customized depending on its format Note that however the emulator does not support the bit field function e Verify In the IO window the verify function of the input value is disabled 11 Illegal Instructions If illegal instructions are executed by STEP type commands the emulator cannot go to the next program counter ENESAS 2 2 Specific Functions for the Emulator when Using the SH7606 The SH7606 does not support the following functions MMU related functions The SH7606 does not mount the MMU VPMAP related command Virtual and Physical specification in the Configuration window Virtual and Physical specification on the command line function Virtual and Physical specification in the Breakpoint window LDTLB instruction execution break function MEMORYAREA_ SET command Profiler function Performance measurement function AUD trace function ENESAS 2 2 1 Break Condition Functions In the emulator three break conditions can be set Break Condition 1 2 3 Table 2 3 lists the items that can be specified for each
6. To our customers Old Company Name in Catalogs and Other Documents On April 1 2010 NEC Electronics Corporation merged with Renesas Technology Corporation and Renesas Electronics Corporation took over all the business of both companies Therefore although the old company name remains in this document it is a valid Renesas Electronics document We appreciate your understanding Renesas Electronics website http www renesas com April 1 2010 Renesas Electronics Corporation Issued by Renesas Electronics Corporation http www renesas com Send any inquiries to http www renesas com inguiry ENESAS 10 11 12 Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is grant
7. any license under any intellectual property rights or any other rights belonging to Renesas Technology Corp or a third party Renesas Technology Corp assumes no responsibility for any damage or infringement of any third party s rights originating in the use of any product data diagrams charts programs algorithms or circuit application examples contained in these materials All information contained in these materials including product data diagrams charts programs and algorithms represents information on products at the time of publication of these materials and are subject to change by Renesas Technology Corp without notice due to product improvements or other reasons It is therefore recommended that customers contact Renesas Technology Corp or an authorized Renesas Technology Corp product distributor for the latest product information before purchasing a product listed herein The information described here may contain technical inaccuracies or typographical errors Renesas Technology Corp assumes no responsibility for any damage liability or other loss rising from these inaccuracies or errors Please also pay attention to information published by Renesas Technology Corp by various means including the Renesas Technology Corp Semiconductor home page http www renesas com When using any or all of the information contained in these materials including product data diagrams charts programs and algorithms please b
8. ccurs is acquired ENESAS 3 Trace information cannot be acquired for the following branch instructions e The BF and BT instructions whose displacement value is 0 e Branch to H A0000000 by reset 4 When User is specified in the UBC mode list box in the Configuration window the internal trace is not acquired In this case exit the Trace window 5 When the SH7606 is used the source code cannot be displayed on the Trace window 2 2 3 Note on Using the JTAG Clock TCK Set the JTAG clock TCK frequency to lower than the frequency of the SH7606 peripheral module clock CKP The set value of the JTAG clock TCK is initialized by executing Reset CPU or Reset Go 2 2 4 Notes on Setting the Breakpoint Dialog Box 1 When an odd address is set the next lowest even address is used 2 A BREAKPOINT is accomplished by replacing instructions of the specified address Accordingly it can be set only to the RAM areas in CSO to CS6 and the internal RAM areas However a BREAKPOINT cannot be set to the following addresses e ROM areas in CSO to CS6 e Areas other than the internal RAM e Areas other than CSO to CS6 e A slot instruction of a delayed branch instruction 3 During step operation BREAKPOINTs are disabled 4 Conditions set at Break Condition 2 are disabled when an instruction to which a BREAKPOINT has been set is executed Do not set a BREAKPOINT to an instruction in which Break Condition 2 is satisfied 5
9. e accessed or modified in sleep state 4 Reset Signals The SH7606 reset signals are only valid during emulation started with clicking the GO or STEP type button If these signals are input from the user system in command input wait state they are not sent to the SH7606 Note Do not break the user program when the RES or WAIT signal is being low A TIMEOUT error will occur If the WAIT signal is fixed to low during break a TIMEOUT error will occur at memory access ENESAS 5 Memory Access during User Program Execution When a memory is accessed from the memory window etc during user program execution the user program is resumed after it has stopped in the emulator to access the memory Therefore realtime emulation cannot be performed The stopping time of the user program is as follows Environment Host computer 650 MHz Pentium IH OS Windows 2000 JTAG clock 5 MHz TCK clock When a one byte memory is read from the command line window the stopping time will be about 40 ms 6 Memory Access during User Program Break The emulator can download the program for the flash memory area refer to section 6 22 Download Function to the Flash Memory Area in the SuperH Family EIOA USB Emulator User s Manual Other memory write operations are enabled for the RAM area Therefore an operation such as memory write or BREAKPOINT should be set only for the RAM area 7 Cache Operation during User Program Break When cache is
10. e sure to evaluate all information as a total system before making a final decision on the applicability of the information and products Renesas Technology Corp assumes no responsibility for any damage liability or other loss resulting from the information contained herein Renesas Technology Corp semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake Please contact Renesas Technology Corp or an authorized Renesas Technology Corp product distributor when considering the use of a product contained herein for any specific purposes such as apparatus or systems for transportation vehicular medical aerospace nuclear or undersea repeater use The prior written approval of Renesas Technology Corp is necessary to reprint or reproduce in whole or in part these materials If these products or technologies are subject to the Japanese export control restrictions they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination Any diversion or reexport contrary to the export control laws and regulations of Japan and or the country of destination is prohibited Please contact Renesas Technology Corp for further details on these materials or the products contained therein Contents Section 1 Connecting the Emulator with the User System 1 1 1 Components of the Em
11. ectronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics C 7 D qa 0 lt D D ENESAS SuperH Family E10A USB Emulator Additional Document for User s Manual Supplementary Information on Using the SH7606 Renesas Microcomputer Development Environment System SuperH Family SH7600 Series E10A USB for SH7606 HS7606KCUO1HE Renesas Electronics Rev 1 00 2005 11 Keep safety first in your circuit designs Renesas Technology Corp puts the maximum effort into making semiconductor products better and more reliable but there is always the possibility that trouble may occur with them Trouble with semiconductors may lead to personal injury fire or property damage Remember to give due consideration to safety when making your circuit designs with appropriate measures such as i placement of substitutive auxiliary circuits ii use of nonflammable material or iii prevention against any malfunction or mishap Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp product best suited to the customer s application they do not convey
12. ed hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document bu
13. een the H UDI port connector and the MCU In addition read the EIOA USB emulator user s manual and hardware manual for the related device Table 1 2 shows the type number of the emulator the corresponding connector type and the use of AUD function Table 1 2 Type Number AUD Function and Connector Type Type Number Connector AUD Function HS0005KCU01H HSOOO5KCU02H 14 pin connector Not available 1 3 Installing the H UDI Port Connector on the User System Table 1 3 shows the recommended H UDI port connectors for the emulator Table 1 3 Recommended H UDI Port Connectors Connector Type Number Manufacturer Specifications 14 pin connector 2514 6002 Minnesota Mining amp 14 pin straight type Manufacturing Ltd Note When designing the 14 pin connector layout on the user board do not place any components within 3 mm of the H UDI port connector 1 4 Pin Assignments of the H UDI Port Connector Figure 1 1 shows the pin assignments of the H UDI port connector Note Note that the pin number assignments of the H UDI port connector shown on the following page differ from those of the connector manufacturer ENESAS Signal SH7606 Pin No TCK N10 TRST M11 TDO N11 N C TMS P11 TDI R11 RES R12 N C GND UVCC Output GND ER GND Output 1 Input to or output from the user system The slash means that the signal is active low The emulator monitors the GND s
14. enabled the emulator accesses the memory by the following methods At memory write Writes through the cache then writes to the memory At memory read Does not change the cache write mode that has been set Therefore when memory read or write is performed during user program break the cache state will be changed 8 UBC When User is specified in the UBC mode list box in the Configuration dialog box the UBC can be used in the user program Do not use the UBC in the user program as it is used by the emulator when EML is specified in the UBC mode list box of the Configuration dialog box 9 Loading Sessions Information in JTAG clock of the Configuration dialog box cannot be recovered by loading sessions Thus the TCK value will be 2 5 MHz 10 IO Window e Display and modification Do not change values of the User Break Controller because it is used by the emulator For each Watchdog Timer register there are two registers to be separately used for write and read operations ENESAS Table 2 2 Watchdog Timer Register Register Name Usage Register WTCSR W Write Watchdog timer control status register WTCNT W Write Watchdog timer counter WTCSR R Read Watchdog timer control status register WTCNT R Read Watchdog timer counter e The watchdog timer operates only when the user program is executed Do not change the value of the frequency change register in the IO window or Memory window e The internal I
15. fice equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions unde
16. gor Darul Ehsan Malaysia Tel lt 603 gt 7955 9390 Fax lt 603 gt 7955 9510 Colophon 4 0 SuperH Family E10A USB Emulator Additional Document for User s Manual Supplementary Information on Using the SH7606 ENESAS Renesas Electronics Corporation 1753 Shimonumabe Nakahara ku Kawasaki shi Kanagawa 211 8668 Japan REJ10J1145 0100
17. ignal of the user system and detects whether or not the user system is connected The ASEMODE pin must be 0 when the emulator is connected and 1 when the emulator is not connected respectively 1 When the emulator is used ASEMODE 0 2 When the emulator is not used ASEMODE 1 To allow the ASEMODE pin to be GND by connecting the user system interface cable connect pin 9 directly to the ASEMODE pin Do not ground the pin Pin 1 mark H UDI port connector top view H UDI port connector top view Pin 1 mark Unit mm Figure 1 1 Pin Assignments of the H UDI Port Connector 14 Pins RENESAS 1 3 1 5 1 Recommended Circuit between the H UDI Port Connector and the MPU Recommended Circuit Figure 1 2 shows a recommended circuit for connection between the H UDI port connector 14 pins and the MPU when the emulator is in use Notes 1 Do not connect anything to the N C pins of the H UDI port connector 2 The ASEMODE pin must be 0 when the emulator is connected and 1 when the emulator is not connected respectively 1 When the emulator is used ASEMODE 0 2 When the emulator is not used ASEMODE 1 Figure 1 2 shows an example of a circuit that allows the ASEMODE pin to be GND 0 whenever the emulator is connected by using the user system interface cable When the ASEMODE pin is changed by switches etc ground pin 9 Do not connect this pin to the ASEMODE pin When a network resistance is u
18. nnnonccnonccnonccnonacconccnano 14 ENESAS ENESAS Section 1 Connecting the Emulator with the User System 1 1 Components of the Emulator The E10A USB emulator supports the SH7606 Table 1 1 lists the components of the emulator Table 1 1 Components of the Emulator Classi Quan fication Component Appearance tity Remarks HS0005KCU01H Depth 65 0 mm Width 97 0 mm Height 20 0 mm Mass 72 9 g or HS0005KCU02H Depth 65 0 mm Width 97 0 mm Height 20 0 mm Mass 73 7 g Hard Emulator box ware User system interface gt 1 14 pin type cable Length 20 cm Mass 33 1 g USB cable 1 Length 150 cm Mass 50 6 g Soft E10A USB emulator 1 HS0005KCUO1SR ware setup program CS gt SuperH Family HS0005KCUO1HJ E10A USB Emulator HSOOO5KCU01HE User s Manual Supplementary HS7606KCU01HJy Information on Using HS7606KCU01HE the SH7606 and Test program manual HS0005TM01HJ and for HS0005KCUO1H HSO005TM01HE and HSO0005KCU02H provided on a CD R Note Additional document for the MPUs supported by the emulator is included Check the target MPU and refer to its additional document RENESAS 1 2 Connecting the E10A USB Emulator with the User System To connect the EIOA USB emulator hereinafter referred to as the emulator the H UDI port connector must be installed on the user system to connect the user system interface cable When designing the user system refer to the recommended circuit betw
19. r certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas El
20. s of conditions that can be set under Break Condition 1 2 3 Table 2 4 Dialog Boxes for Setting Break Conditions Type Address Bus Data Bus Bus State Count Condition Condition Condition Condition Internal Dialog Box Address Data Bus Status Count 1 0 Break Break Condition 1 O O O O X dialog box Break Condition 2 O X O X X dialog box Break Condition 3 X X X X O dialog box Note O Can be set in the dialog box X Cannot be set in the dialog box 2 2 2 Trace Functions When the SH7606 is used the trace functions listed in table 2 5 can be used Table 2 5 Trace Functions Function Internal Trace Branch trace Supported four branches Range memory access trace Not supported Software trace Not supported Internal Trace Function This function is activated by selecting the Internal trace radio button in the Trace type group box of the Trace mode page This function traces and displays the branch instructions The branch source address and branch destination address for the four latest branch instructions are displayed Notes 1 If an interrupt is generated at the program execution start or end including a step execution the emulator address may be acquired In such a case the following message will be displayed Ignore this address because it is not a user program address 2 If a completion type exception occurs during exception branch acquisition the next address to the address in which an exception o
21. sed for pull up it may be affected by a noise Separate TCK from other resistances The pattern between the H UDI port connector and the MPU must be as short as possible Do not connect the signal lines to other components on the board When the power supply of the user system is turned off supplying VccQ of the user system to the UVCC pin reduces the leakage current from the emulator to the user system A level shifter that is activated by the internal power supply or user power supply changed by the switch is installed in the interface circuit of the emulator If the user power is supplied to the UVCC pin the level shifter is not activated as long as no user power is supplied When the power supply of the user system is turned off no current flows from the user interface The I O voltage level of the user system interface can be the same as that of the VccQ To operate the emulator with low voltage lower than 3 3 V the VccQ must be supplied to the UVCC pin Make the emulator s switch settings so that the VccQ will be supplied SW2 1 and SW3 1 as shown in figure 1 2 The resistance value shown in figure 1 2 is recommended For the pin processing in cases where the emulator is not used refer to the hardware manual of the related MPU ENESAS When the circuit is connected as shown in figure 1 2 the switches of the emulator are set as SW2 1 and SW3 1 For details refer to section 3 8 Setting the DIP Switches in the SuperH
22. t Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers of
23. tions have been executed 4 IfaPC break address condition is set to the slot instruction after a delayed branch instruction user program execution cannot be terminated before the slot instruction execution execution stops before the branch destination instruction 5 Note that a break occurs with a break satisfaction condition by an instruction that has been cancelled due to the generation of an exception 6 Use the sequential break or count break with the L bus condition If such break is used with the I bus condition it will not operate correctly 7 A break will not occur with the execution counts specified on the execution of the multi step instruction 2 2 6 Note on Setting the UBC_MODE Command In the Configuration dialog box if User is set while the UBC mode list box has been set the STEP type commands that use Break Condition 2 for implementation cannot be used ENESAS SuperH Family E10A USB Emulator Additional Document for User s Manual Supplementary Information on Using the SH7606 Publication Date Rev 1 00 November 2 2005 Published by Sales Strategic Planning Div Renesas Technology Corp Edited by Customer Support Department Global Strategic Communication Div Renesas Solutions Corp 2005 Renesas Technology Corp All rights reserved Printed in Japan Renesas Tech nology Corp Sales Strategic Planning Div Nippon Bldg 2 6 2 Ohte machi Chiyoda ku Tokyo 100 0004 Japan ENESAS RENESAS SA
24. ulators nsss eissidas e anera Eorna eeina 1 1 2 Connecting the EIOA USB Emulator with the User System u ssursessnesnesneennennnennn 2 1 3 Installing the H UDI Port Connector on the User System ssssesseeseereersresrrerrsrrerrsrseesee 2 1 4 Pin Assignments of the H UDI Port Connector u suesserssersnesnnesnersnersnernnennnensnennnennen nn 2 1 5 Recommended Circuit between the H UDI Port Connector and the MPU 4 1 5 1 Recommended Circuit uessserssessnesnnesnensnensnennnennnennnennnennnnnnonnnennnennnnrnnnnannnanen 4 Section 2 Specifications of the Software when Using the SH7606 7 2 1 Differences between the SH7606 and the Emulator u 22u422440rsnernnennnennnennne nennen 7 2 2 Specific Functions for the Emulator when Using the SH7606 2u 2244224nnn nennen 10 2 2 1 Break Condition Functions 2 c sseccseacssessestascdsescapceoessoostoghtenetonsesasdsatesacasasezans 11 2 2 2 Trace Functions citrato tia letter lan rior a ia 12 2 2 3 Note on Using the JTAG Clock TCK ooooconnncccnocccionncononcnoncconnncnonccnnnccnonaconnncnnno 13 2 2 4 Notes on Setting the Breakpoint Dialog BOX ooooonncnncnnnnnnnnnoccnonconnnancnanonanonnnos 13 2 2 5 Notes on Setting the Break Condition Dialog Box and BREAKCONDITION_SET Command coccocccnnncnnnnnconnnnnonnnnnonnnnnonncancnncnn conc rnncnncnnos 14 2 2 6 Note on Setting the UBC_MODE Command occcocccnonccnonccnon
Download Pdf Manuals
Related Search