Product information Video indoor station IVX9001-0140
Contents
1. Open the device es e There is a release mechanism at the underside of the device Slight ly press into the opening with a screwdriver e Now the upper cover can be re moved from the underside and separated from the lower cover e Lift the upper cover from the two upper latches 5 wire special operation If there are only 5 wires available for the device it is possible to operate it gl I in 5 wire special operation an Amu e Connect the b and M wire with one wire bridge Commissioning First install the system completely then connect it to mains voltage e Install the devices of the system completely e V1 and V2 must not be connected to P a or b wire When connect ing the video wires V1 and V2 the polarity must be observed e Check the a b and P wire against each other for short circuit e Switch ON the mains voltage Both LEDs are blinking 3 x green The indoor station is ready for ope ration Settings AS address dependent image activation If there are also front door stations without camera in combination with video front door stations within one systems the image is not activated if a call from such a front door station comes in To guarantee this function the possible AS addresses are separated into image is activated in case of a door call of max 16 video front door stations two areas AS addr2. lore up ODown 21 Setup Intercom Setup user Opera tion level for the user e Press the menu button in stand by mode Setup Intercom j 2 Set Install e Press the image button etup Installer or the function key O to select the menu Setup In tercom e Press the speech button Goff Cup Ovown Mok q to get to the menu Setup user Setup User Ring Vol BEEREN i l e Press the image button or the function key O to Contrast change the parameter oe Key tone Activate deac tivate the key tone Key tone is activated When pressing the sensor button a tone sounds Ring tone volume Ring tone volume 8 steps Brightness Screen brightness 20 steps Contrast Image contrast 20 steps Color Color saturation 20 steps Dorff Cup Setup Installer Operation level for the qualified electrician For descriptions see Settings This level is priorised for vja OSD page 12 authorised persons only 22 General information on the conduit in TCS video systems 6 wire operation The 6 wire operation is the standard operation mode Video operation which is used with two separated earth connections b and M The conduit is determined by the structural conditions and is limited only by its length Observe when selecting the cable length the loop resistance of a b and M P must not exceed max 8 Q table 1 When the loop resistance exceeds g
3. aF pe an DG fj acs t vs AS front door station VS power supply and control unit IS indoor station TO door opener Note The max number of front door stations that can be connected is limited For detailed description see product information 24 Technical data supply voltage housing dimensions in mm weight acceptable ambient temperature input current max input current video module screen diagonal resolution video signal input floor video input Video 6 wire technique necessary 24 V 8 power supply and control unit plastics white H 180 mm x W 95 mm x D 19 mm 240g 0 C to 40 C l a 0 4 mA I P 33 mA stand by I Pmax 200 mA TFT color module 8 9 cm 3 5 inch 320 x 234 Pixel RGB symmetrical 1 Vss FBAS asymmetric 1 Vss FBAS 25 FAQ Error pattern Possible causes Our suggested solution The video image is black and white The color saturation control of the indoor station is set to a mini mum Adjust the contrast or color satura tion control The transmission level of the video BUS is too low At many components of the video BUS e g FVY the transmission level can be adjusted Please see the product infor mation of the active transmission components The light intensity does not reach the minimum value of 10 lux Thus the camera switches over to black and white The camera module of the front door station is very inse
4. button I lt to end the voice communication Sendan e Press the menu button Main menu internal in stand by mode to open PETTERS call the main menu 3 dieen Een e Press the image button 4 Setup Intercom or the function key O to select the menu nternal call ee ee If an internal call was con off up _ Opown Kok figured e g the room or the serial number of the Internal call call destination is dis played on the screen Ben Mate N87 e Select the call destination e g facility manager e Press the speech button q to call another indoor eS enn station lore up Opown Kok e If there is no internal call Internal call configured Display No internal call No internal call Dorff up Opown tox Callthe e Press the door release central button O or the function key O depending on your configuration to call the central If a call comes in at the indoor station press the speech button I lt to speak with the person at the cen tral Shortly press the speech button Sto end the voice communication 19 Video surveillance Video sur veillance e Press the image button O e f several video front door stations or cameras are connected you can switch between these by pressing the image button again e Press the call OFF button amp to switch OFF the im age The image switches OFF automatically after the de termined period of time ran out Front do
5. nere ere nneniardten eee 12 OCR Me asi asa as eenden ee tenen nde ee he a 16 Sendinga call meereden aren elen edes den EER 18 Switching lights and send control functions ea 21 Automatic TUNIC UOME eters Sereen Rae ner teeta 21 DOG TD TELCO Neaera ereen ene beenderen end traden 22 General information on the conduit in TCS video systems 23 Wire OD STATION secesi erea i E Tipee EET e eeen 23 Max number of IVX9001 0140 in 6 wire operation 24 Technical data ssezer seegers ennen sardana eare seen cxadscceemetriazsaussccnemees 25 EE 26 Cleaning Seri er or eT nnee deinende enge eerd neder 28 Information on disposal nnnnnanennneneennnnnnnennenne nee ennnnnnnnnnenneneeenn 29 Warta es cee asia ak cena Ee ah A da 29 GEVO e sccecesscceisesscececeteccctesssseccensvessneesacnscceeueasexersuasueteeuertensevasnseseeecteses 30 Scope of delivery 1 x Video indoor station IVX9001 0140 Product information User manual Safety instructions Attention Mounting installation commissioning and repair of electronic devices have to be carried out only by qualified elec tricians Thus the standards and instructions for the installation of systems have to be observed For working on systems with main connection of 230 V alternating volt age the safety requirements according to DIN VDE 0100 must be ob served When installing TCS BUS systems the general safety regulations for telecommunicatio
6. or lights Factory setting e Press the image button to reset the systems pa rameter to the factory set tings Reset Note Store the settings by pressing the speech button The selection symbol switches over to the next position User Einrichten Sprache German MIC Vol EEEEE Spk Vol EE Funktionstaste Werkseinstellung Reset Eus dok auf OAb Device informa tion The information on the device is available under Device in formation 15 Operation To accept a call Door call e In case of an incoming call 4s speaking amp End from a from a video front door video station the screen is au front tomatically activated and door sta the video image is dis tion played e Shortly press the speech button I lt to speak to the person who is in front of the door AS 1 SA End e When a voice connection GRE is established the LED 2 is ON e Shortly press the speech button If to end the voice communication e Shortly press the door release button O to open the door Door call e In case of an incoming call from an from an audio front door audio station a ring tone sounds front at the indoor station No door sta video image is displayed tion e Shortly press the speech button SIF to speak with the person in front of the door Shortly press the speech button q to end the voice communica
7. 1G Product information Video indoor station IVX9001 0140 Table of contents Scope of delivery rossen szenerneeeeeersrnnnaernennernenateandnrnnnenrned dmt nanhennen eden 3 Safety INStrUCtIONS s ts nsresteteendentenarnetenenrvetnnn naar dnne alwetend natnsnaddden 3 Installation protective measures nnen eennenennneeen eneen 3 Device OVeIVICW asss esssenerneneeeteens den taagedsetnaeheen di kaai aaraa keerde hanne 4 Indication and operating elements nnen nne ennnnnneeneeee nee eennnennn 5 Intended US zzaaterenrverzen oenen usanne seeds een euntnnen nende den aante naaa deden Seaia iaaii 6 Short description zr sarren nsenreeneaterndnnnehkansnaeninen nnmnnn nnna 6 Mounting and installation nnn nnnnnnnnnneeneeneennnnnnnnnenneeeennnnnnnnn 7 Install the lower Cover tarzn dede dae ae 7 Installati n heights ira ienei etten 7 Installation on flush mounted socket nnee 7 Set indoor station as end device nnen nnnnennnen nere eennnnnnenen 8 Snap on the upper cover nnnnnnnnnnnneeneerrennnnnnneeneeneneeennnnnnnenenn 8 Open the AVE nattere entente eeen kette 9 5 wire special operation Endre reeet 9 COMMISSIONING E aaien edes khan sensei hnae denna 9 SC HUTA noe entente TTE 10 AS address dependent image activateion nnen eeen 10 Pre settiNngSs Gx WOKS 5 rant eeentendndenee neede ea ede dean 10 Configuration Options sten rtetienne te eb eaccneina netics 11 Settings via OSD MENU eirgstereennrgne
8. board and paper resp plastics y Warranty We offer a simplified processing in case of warranty for electricians e Please note our conditions of sale and delivery for download from www tcsag de Downloads trade information e Please contact the TCS HOTLINE 29 Service Please send your questions and inquiries to hotline tcsag de Headquarters TCS T rControlSysteme AG Geschwister Scholl Str 7 39307 Genthin Phone 49 0 39 33 87 99 10 FAX 49 0 39 33 87 99 11 Mail info tcsag de www tcsag de 30 Subject to technical changes TCS Hotline Deutschland Phone 49 0 4194 9 88 11 88 FAX 49 0 41 94 9 88 129 Mail hotline tcsag de PI_IVX900x 2A 12 2014
9. c call cut off optical signaling of door and internal calls by a green LED optical indication of door stand by time on service call by a green LED optical indication when activating door release automatic or call diver sion by a green LED acoustic ring tone distiction in case of two different door calls door call AS border 2 0 floor calls and internal calls adjustable functions in the OSD menu AS address image switch time length of call OSD information language microphone sensitivity con versation volume ring tone volume color saturation brightness and contrast of the video image send control functions 8 function key button tone can be deactivated floor video image activation can be realised with an additional FBAS video input for another camera on terminal C optional floor push button can be connected Mounting and installation Install the lower cover Attention The video indoor stations have to de installed only volt age free Ensure not to over tighten the fastening screws when installing the lower cover on uneven ground Over tightened fastening screws can deform the lower cover Thus you may not be able to snap on the upper cover or the secure contacting between the lower and upper cover may be affected Installation height Lower cover For an optimal viewing angle 9 amp we recommend an installation up height of 1 60 m upper edge of the device above floor level Position flu
10. cessary via a video switch to the existing TCS BUS No image Image switch button does not respond when pressing No signal present Connect the monitor in front of the video switch and check whether a signal is available here Measure the voltage between P and b The voltage usually is about 24 V If this is not the case please check the BUS power supply Not both wires of the video BUS are connect ed Please check the connection of the pluggable terminal Video image turns white after a while When switching the supply voltage off and on again the signal will reappear The video image turns white again after a while Thermal defect of the outdoor camera A wire of the video BUS short circuits the P or the b wire This causes an impermissible in creased current Please check the wiring for shorts The camera is defect Cleaning Avoid water from entering the device Do not use any abrasive detergents Clean the device with a dry or slightly wet cloth Remove stronger stains with a mild household cleaner 28 Information on disposal The adjoining symbol shows that the device has to be bd disposed separately from domestic waste Thematerials used are recyclable PLease do help protecting our environment and mums dispose the device via a collection point for electronic scrap lt A Dispose the parts of the packaging in collecting tanks for card Jac
11. ds a terminating resis tor In one building block with multiple indoor stations only one indoor station shows black lines on the video image Image interferences due to transition resistance The P wire is not connected cor rectly The connection contacts are not completely fixed Image interferences due to near disturbing sources such as external power supplies or other electric appliances which are not shielded Relocate the video distributer or any other passive assembly pack age Distortion due to com pensation currents caused by potential dif ferences Please check the line installation and try to install active compo nents on one potential No accurate video signal due to interchanged video wires The video BUS is not reverse polarity protected Please interchange the wires V1 and V2 The image rolls The video signal cannot be synchronized Please check if all wires of the video BUS are connected If necessary please adjust the video level Multiple contours occur Image reflections occur so called ghost images due to open lines The video strand is not connected Please insert the terminating re sitor in the last device of the strand 27 Contours of the second image are visible Two video sources inter fere Please remove the second video source from the line Connect the second video source if ne
12. ess reserved for video front 0 47 door stations AS address free for front door stations 48 63 without camera image is not activated in case of a door call The video AS border can be modified only with the configuration software configo Pre settings ex works OSD information activated Language German Microphone sensitivity 5 of 8 Conversation volume 3 of 8 Ring tone volume 5 of 8 Brightness 4 of 20 Contrast 10 of 20 Color intensity 14 of 20 Length of call 10 to 120s Remaining conversation time activa 4 Ss tion of the door opener Image switch time 60 s Blinking period of the red LED BUS e f video speech channel busy when pressing the speech button or the image button 6s 3 x blinking e if video speech channel busy when a door call comes in for im age activation when busy 10s 5 x blinking Internal stand by time e if the indoor station is called 2 min e if the indoor station is calling and waiting for call acceptance 30 s Floor door release time 35 s Timeout OSD 10 bis 120s Timeout video image 10 bis 120s Configuration options Function Menu Fixed simplex communication Simplex communication to the front door station Ring tone volume Ring tones for door calls internal calls and floor calls x lt Call diversion Button tone ON OFF Door release automatic Internal call
13. max 10 Control function 8 9 10 light switch f x lt X lt gt X lt gt X lt X Determine video AS border and door call AS border x lt Image activation when a floor call comes in floor video function x lt Image switch time Length of call Parallel allocation Set delete floor door release function x lt gt x lt gt lt X lt Automatic hands free talking after inter nal call ON OFF Image settings 11 Settings via OSD menu Setup This level is permitted for thein authorised persons only Main menu staller x 2 Light d trol Operat Press the menu button E E oLan 0 A in stand by mode to open 4 setup Intercom OTIS the main menu qualified electrician Eoff up Opown ok e Press the image button or the function key O to Setup Intercom select the menu Intercom 1 Set up User settings e Press simultaneously the Eoff up Obown Kok call OFF button amp and the image button 1 to getto Set up Installer the menu Set up Installer 2 AS address 3 Parameter 4 Internal call 5 System 6 Information on device Eoff up Opwown Kok 12 Ring In the menu ring tone the tone ring tones for door calls from Ring tone the front door station max ET Alpha2 8 floor calls and internal Door3 Tone Alpha2 Door4 Tone Alpha2 calls can be set Doors Tone Alpha1 e Press the image button Doo
14. n systems according to VDE 0800 must be observed Inter alia separated conduit of heavy current and low current lines minimum distance of 10 cm in case of a common conduit use of separators between heavy and low current lines within shared cable ducts use of standard communication e g J Y St Y with 0 8 mm diameter existing lines modernisation with deviating cross sections can be used in compliance with the loop resistance Installation protective measures With suitable measures to protect against lightning it has to be en sured that a voltage of each 32 V DC is not to be exceeded at the connections a b P M Device overview Sensor buttons Image button Call OFF button Menu button Function key Loudspeaker Microphone Screen LED red LED green Door release button Speech button sensor button Indication and operating elements Description Function Ea Screen display of the video image menu display OSD LED red is ON call OFF is activated ring tone mute blinks indication busy voice channel LED green is ON when a voice connection is established when call diversion and door release automatic are activated Call OFF button ring tone mute if no voice connection is estab lished end speaking back in stand by mode Menu button open the main menu close the main menu back to the previous menu Image button ac
15. nsitive to light Please arrange for a suffi cient illumination or use external cameras The colors of the video image are too bright or the image in general is too bright The color saturation control of the video in door station is too high Reduce the color saturation The brightness control is turned on too much Reduce the brightness The level of the video signal is too high Reduce the level of the video bus e g rotary control on the camera board This only works if the bus termination at the video indoor station or at the active extended function is inserted correctly e g FVY The matching resistor at the end of the strand is not inserted Please place the matching resis tor Colors of the video image are without contrast 26 The level of the video signal is not high enough The connection line of a surface mounted camera was inadmissibly extended The cable length between two active video components was inadmissibly exceeded Video level loss can be regulated via the rotary control in active video components see product information of the components Please check if the number of allowable video indoor stations per line was not exceeded The matching resistors are not inserted correctly at the video distributors Remove the terminating resistors at the relevant components Only the last video component in one strand nee
16. or Next amp End Floor video e To display the floor video image confirm the image button C if the floor vid eo function is activated Floor door Next End Video front door station e Press the image button to switch to the image of the video front door sta tion Front door 20 Switching lights and send control functions Light and e Press the menu button control in stand by mode to open the main menu e Press the image button or the function key to select the menu Light and control e Press the image button or the function key O to select a function control function 8 9 or 10 or send light switch function e Press the speech button q to trigger the control function or to switch the lights Main menu 2 Light and control 3 Automatic function 4 Setup Intercom Soff lok up ODown Light and control 2 Control function 9 3 Control function 10 4 Light switch function Soff Ou Opoun fox p Automatic function Automa tic func tion Etagen t r ffner Rufumlei tung e Press the menu button in stand by mode e Press the image button or the function key O to activate deactivate the function e Press the speech button to trigger the control function or to switch the lights Note Store the settings by pressing the speech button Is Automatic function Call diversion deactive
17. r6 Tone Alpha2 or the function key O to Daor7 Tone Alpha2 Doors Tone Alpha2 set the ring tones Internal call Gong When selecting the ring Floor call Alphas tone the ring tone sounds Soft Cup Odown immediately Note After you made the settings please press the speech button d Sto store the settings and to switch to the next menu point Video AS To one indoor station max 8 border front door stations can be AS address allocated AS address from 0 to 63 0 47 for video front door station as of 48 for audio front door station e Press the image button function key to change the AS address e Press the image button or the function key to set the video AS border Note Store the settings by pressing the speech button The next line is highlighted Door2 Door3 Door4 Doors Door6 Door7 Doors AS empty empty empty empty empty empty empty lore up ODown dok 13 Parame ter Image switch time The screen switches OFF after the determined period of time flat 60 s Length of call The indoor station switches OFF after the determined period of time The time can be adjusted from 10 to 120 s Parallel SN Enter the serial number of the indoor station which should be displayed when a call comes in Floor camera Activate deactivate if an other camera should be con nected Floor door opener Activate deactivate Floor door opener is ac
18. sh wassen mounted socket A S k Installation on flush mounted 2 tastehind i socket screws on flush 8 e Position the flush mounted Mounted socket S oe socket below the cable gland sd it ZES e According to the illustration z REA attach the lower cover at the stonin qe attachment holes to the flush screws all 4g e mounted socket or to the wall mounting with suitable screws Connect the lines e Minimise the length of the lines above the lower cover to place the lines with out any problems and to prevent clamping the lines when snapping on the upper cover e Connect the lines according to the labeling within the lower cover to the connection terminal The terminal can be removed from the quide rail e Run the lines along the dedicated site e Ensure that there is no uninsulated or not connected wire e g cable shield in the space for cabling as this could cause a short circuit Set indoor station as end device The indoor station is positioned at the end of a strand or is the only device in the strand e Push the slide switch S1 on the print ed circuit board in the upper cover to the right Thus the matching resistor is placed scope of delivery not placed Snap on the upper cover e Set the upper cover on both latches of the lower cover 1 e Snap in the upper cover with slight pressure 2 abEPMCV1 V2 JavEPNCWR te
19. t 8 Q plan multiple wiring of the strands double twisted lines optional strand or star formed wiring Do not use more than 20 video indoor stations per strand For systems with more video indoor stations use video distributors FVY1200 FVY1400 Up to 64 front door stations 16 of them video front door stations and an almost unlimited number of indoor stations can be connected polari ty free a b within one system polarity free only in 6 wire operation Thus a suitable power supply and control unit is to be used Table 1 Loop resistances cable length cable diameter a b M P in m 0 6 mm 0 8 mm 10 0 71 20 1 43 30 2 14 40 2 86 50 3 57 60 4 29 70 Se See 5 00 80 eT 5 71 90 Ooo y 6 43 100 SSS 7 14 23 Principle loop resistance Measure loop resistance e Switch off the 230 V 50 Hz of None of the devices AS IS or FE the VS should be further than 8 Ohm away Install a b short circuit at the VS from the power supply and control unit VS e Other devices are not disturbing the measurement they can stay connected a b short circuit e here 8 Ohm vs around 65 m distance AS VS by 0 6 AS front door station mm diameter VS power supply and control unit around 115 m distance AS VS by 0 8 IS indoor station mm diameter FE extended function Max number of IVX9001 0140 in 6 wire operation max num small and me f dium sized bero El IVX9001 DN od systems AS IS 0140 s VBVS05 12 in
20. tion Press the call OFF button amp to end the voice com munication Internal call from another indoor station e In case of an incoming call from another indoor sta tion a ring tone sounds at the indoor station No vid eo image is displayed Shortly press the speech button K to speak to the person at the other indoor station Shortly press the speech button K to end the voice communication Press the call OFF button amp to end the voice com munication Floor call When a floor call from a floor door comes in short ly press the speech button Sto speak to the person at the floor door Shortly press the speech button I lt to end the voice communication If the floor door release function is activated press the door release button O to open the floor door only possible up to 35 seconds after the call has come in If the floor video function is activated the video image is displayed Floor door O Open A End 17 Call from the cen In case of an incoming call tral from the central shortly press the speech button q to speak to the person at the central e Shortly press the speech button K to end the voice communication Sending a call rae e In stand by mode Press Bee See EN Tant the speech button q to aber Sse establish a voice commu on nication with front door station which was con nected last e Shortly press the speech
21. tivate image switch image between different cameras if available switch OFF the image upwards in the OSD menu change parameter in the OSD menu O Function key send control function 8 for calling the central if the IVX9001 0140 is configured for systems with central dwonwards in the OSD menu change parameter in the OSD menu Door release button door release during a voice connection for calling the central if the IVX9001 0140 is configured for systems with central d Speech button e accept a call door call or internal call speaking is activated end speaking confirm parameter selection store Intended use The video indoor station IVX9001 0140 is a video indoor station with color display for hands free talking The IVX9001 0140 is suitable for the operation in building communica tion systems with combined audio video systems The operation is realised via the sensor buttons and the On Screen Display OSD The video indoor station IVX9001 0140 is suitable for surface mount The video indoor station is to be installed preferably on a wall outlet one gang box or a flush mount socket as the space for cabling is limited within the device Short description hands free talking 13 ring tones can be programmed by a qualified electrician door release button function key ring tone mute with optical indication LED red audio and video privacy function as well as an automati
22. tivated By pressing the door release button O the control function 11 is sent Can be used to open the floor door Call diversion Activate deactivieren Call diversion SN Enter the serial number Door release automatic Activate deactivate Note Store the settings by pressing the speech button ls The selection symbol switches over to the next position Parameter Length of call 45 Parallel call SN 21 Floor camera Floor door Call diversion Call diversion SN Door automatic deactivated permitted permitted deactivated ort uv Opown K ok 14 Internal call des tinations e Enter the room and serial number of the indoor station for internal calls e Max 10 internal calls can be configured e Press the image button OD function key O to change the room and serial num ber The numbers must be adjusted individually Note Store the settings by pressing the speech button I lt The selection symbol switches over to the next position Internal call Ro Ro Ro Ro Ro Ro Ro Ro 02 Ro Dorff oee ES ooo EE Hz ODown up System OSD information displays date time and status etc when a voice and video con nections is established Language language setting OSD German and others MIC Vol microphone sensitiv ity 8 steps SPK Vol volume of the loud speaker 8 steps Function key CF 8
Download Pdf Manuals
Related Search