Owner Manual - Energizer Generators
Contents
1. Hubber washers 15 2 lt 16 hergizer Chapter 3 Setting Up Your eZG3500 Generator oetup should be done everytime you start up your generator these quick checks will ensure you get the most out of your generator Exhaust gas contains poisonous carbon monoxide Never run the generator in an enclosed area Be sure to provide adequate ventilation Operate the generator on a level surface If the generator is tilted fuel spillage may result Keep away from rotating parts while the generator is running The generator is air cooled and may be damaged if ventilation is inadequate 3 1 Checking the Engine Oil Level 5 Ensure the generator is on a level surface 6 Inspect engine oll e Take out the oil filler cap and clean the dipstick e Check the oil level by reinserting the oil filler cap without rotating it Remove the oil filler cap and examine the oil level If the oil level is at or below the minimum oil level refill the oil to the maximum oil level mark 10W30 Reinsert the oil filler cap and tighten securely Refer to figure below Maximum Oil Level Minimum Oil Level Engine oil is a major factor affecting engine performance and service life Non detergent or vegetable oils are not recommended eZG cios 3 2 Checking the Engine Fuel Level 1 Check the fuel level by reading the gauge or removing the fuel tank cap to visually2. lt OTHER WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OF ANY OTHER WARRANTY WHETHER EXPRESS OR IMPLIED Consumable parts such as oil or fuel filters fuel cut off valve brushes fuel injection nozzle valve lubricant or ignition plug are not covered under this warranty All expenses incurred in maintaining and replacing parts for generator shall fall on the purchaser This warranty coverage does not include parts affected by accident and or collision corrosion or rust normal wear incorrect fuel type or fuel contamination use in an application for which the product was not intended unauthorized service or any other misuse neglect incorporation or use of unsuitable attachments or parts Damage to voltage regulators caused by failure to ground shorting or overloading will not be covered under this warranty Under this Warranty we do not have the obligation to bear any transportation fees of any product to from an authorized Warranty Center Unauthorized alteration installation or any cause other than defects in material or workmanship of the product will not be covered under the warranty EXCLUSIONS NOT COVERED BY THIS LIMITED WARRANTY 1 Normal engine alternator wear 2 Damage caused by lack of maintenance as described in the Energizer User Guides or negligence by using improper or impure motor oil coolant or fuel 3 Damage caused by accidents improper installation or storage Damage caused by water in
3. 1 877 528 3772 www energizergenerators com EZG3500 MEETS ALL CERTIFICATION REQUIREMENTS FROM she EPA 248027 EZG3500CA MEETS ALL CERTIFICATION REQUIREMENTS FROM California Environmental Protection Agency 967 _ b Y 4 Oz Air Resources Board hergizer Contents Page Safety First Safety while using your generator Understanding AC safety Safety while maintaining your generator Other safety tips Learn About your New Generator Identification of Parts Making Sure You Have Everything Mounting Instructions Setting Up your Generator Checking the Oil Level Checking the Engine Fuel Level Checking the Air Filter Using your EZG3500 generator Starting Your Generator Using the EZG3500 with your Appliances otopping your Generator Maintaining your Generator Maintainance Schedule General Inspection Tips Cleaning the Air Filter Changing the Engine Oil Replacing and Cleaning the Spark Plug Handling and Storage Troubleshooting Specifications Wiring Diagram Learn About your Warranty 00 4 C 11 13 14 17 18 19 20 22 23 24 24 25 26 or 28 30 31 32 33 eZG cios Chapter 1 Safety First Playing it safe when working with power equipment is always a good idea Here are some important precautions to make sure you stay safe 1 1 Safety while Operating Your Generator Always perform an oil fuel and air filter check before starting the engine ENEIGIZE Properly cl
4. Voltage V 120V 240V 7 0 HP Single Cylinder forced air cooling 4 stroke s OHV Ignition mode Transistor Controlled Ignition 5 Max Output W rpm 3800 3600 9 16L Fuel tank capacity 15L CA model Oil capacity 600mL 10W30 Fuel Type Unleaded gasoline Running Volume 80dB at 7m Running Time Per Tank hours 11hrs with 75 load cQ 53kg Dry Weight 54kg CA model Allow engine to rest for 30 minutes before starting another running cycle 20 Chapter 8 Wiring Diagram 1109 Bea ir 110 59 9 2 440 x e NOLLONN4 HOLIMS 3NIBN3 3JIHWYOV Tg dad c z zz z AVR ONINHVM 110 C POWER CONTROL GENERATOR BLOCK ENGINE CONTROL PANEL D D d3 V3u8 OV i 1 32 HOLIMS 3NI9N3 090 06 00 d3 V3u8 OV Energizer Chapter 9 Learn About your Warranty Energizer Power Equipment Customer Support Center Toll Free 1 877 528 3772 E mail support energizergenerators com Online www energizergenerators com ENERGIZER POWER EQUIPMENT PRODUCTS ARE DISTRIBUTED BY Midland Power Inc Product Registration 3 6 Magnetic Drive Toronto ON M3J 2C4 Canada This product is warranted to be free of defects in material and workmanship for two years from date of purchase This warranty guarantees that any defective parts will be repair
5. clean water because repeated exposure to lubricant may cause skin irritation Do not clean the filter element with flammable liquids like gasoline because an explosion may occur gt eZG cios 1 4 Other hergizer Turn off the engine before performing any maintenance Otherwise it can cause severe personal injury or death Allow the generator set to cool down before performing any maintenance Always wear safety glasses when cleaning the generator set with air Do not clean the generator set with a pressure washer because it can cause damage to the generator set Before working with batteries ventilate the area wear safety glasses do not smoke and always disconnect the negative cable first and reconnect it last Use rubber gloves when coming into contact with engine oil Always stop the generator set before removing the oil filler cap Only qualified maintenance personnel with knowledge of fuels electricity and machinery hazards should perform maintenance procedures Lubricate all exposed metal parts regularly Safety Tips To avoid breathing in poisonous carbon monoxide from the exhaust gases adequate ventilation should be provided if the generator set is running in a partially enclosed space If the generator set is stored outdoors check all the electrical components on the control panel before each use Moisture can damage the generator and can lead to an electric shock If you start to feel sick dizzy or we
6. to dry thoroughly or clean in non flammable solvent and allow to dry o Dip the foam filter in clean engine oil then squeeze out all excess oil The engine will smoke when started if too much oil is left in the filter 6 Wipe dirt from the air filter unit and cover using a moist rag eZG crcs 5 4 Changing the Engine Oil Used motor oil can cause skin irritations if left in long tern contact with skin Wash hands thoroughly with soap and water after handling oil Do not dispose of used oil in drains or on soil Local service shops provide environmentally friendly disposal methods 1 Stop the engine and remove oll filler cap 2 Place a pan under the engine 3 Remove the oil drain screw and allow the oil to completely drain into the pan 4 Reinstall drain screw before filing the engine with fresh oil Do not overfill oil reservoir Use a funnel to prevent spillage 5 Reinstall the oil filler cap and tightly fasten Oil Drain Screw Oil Pan Underneith 26 Energizer 5 5 Replacing and Cleaning the Spark Plug Do not rinse spark plug in water Follow guidelines and be careful not to overtighten the spark plug Tighten turn when installing a new spark plug Tighten turn when re installing an old spark plug 1 Disconnect and remove the spark plug using a wrench 2 Inspect the spark plug and clean any dirt from the electrodes with a wire brush If electrodes are worn or show signs of
7. wear replace spark plug 3 Measure the electrode gap with a spark plug gauge and adjust as necessary by bending the side electrodes Ensure that the gap is between 0 7 and 0 9mm 4 Reinsert the plug carefully Tighten with a spark plug wrench eZG cios 5 6 Handling and Storage Handling 1 off the engine switch and the fuel valve when transporting the generator set 2 Do not touch engine until the engine has cooled down 3 Keep the generator at a level position in order to prevent spillage Storage Before storing the generator set for an extended period 1 Ensure that the storage area is free of excess humidity and dust 2 Drain the fuel tank and the carburetor Draining the Fuel Tank 1 Turn OFF the engine Remove the fuel cap and the debris screen underneath the fuel cap 2 Empty the fuel tank using a siphon and an approved gasoline container Fuel Cap o8 x Fuel Tray e Syphon 28 Energizer Draining the Carburetor 1 Turn OFF the engine Let Cool Turn the fuel valve ON 2 Position a container under the carburetor drain screw Loosen the drain screw 3 Allow fuel to drain completely drain and re tighten the drain screw c LING 2114 1 Wr Carburetor Drain Screw N P Container Note on Automatic Voltage Regulation AVR Your generator is e
8. ENEIGIZEI eZG 5700 220 3000W GAS POWERED PORTABLE GENERATOR Energizer 26 1 2014 Energizer Power Equipment All Rights Reserved Licensed by Energizer Corporation United States of America EZG3500 03 2013 01 Let s get started You re excited to power up so we ll keep this brief eZG cios Thank you for purchasing your eZG3500 generator Remember to register Take a minute to register this product online at www energizergenerators com This will allow you to request warranty support in the future This manual will show you how to use the great features that sets the eZG3500 apart from the crowd We ve got you covered Call us at 1 887 528 3772 if you have any questions This user guide covers the safety operation and maintenance procedures for the eZG3500 All information in this publication is based on the latest product information available at the time of print Visit www energizergenerators com for user guide updates and operation notices No part of this publication may be reproduced without written permission It is important that anyone operating this product read and understand the manual prior to use eZG cios Warranty Information Warranty support operation assistance and product support is provided by Midland International Inc a licensed manufacturer of En ergizer Power Equipment Please contact us directly for any warranty service questions
9. Rester loin de l chappement Tank Capacity Capacite du reservoir 2 2 Make Sure You Have Everything Number Part Name Quantity 1 eZG3500 Generator Handle Bracket Bolt 1 Handle Axis Bolt 1 Handle Bracket Handle Axis Nut 1 Handle Lock Pin amp Leash Handle Bracket Bolt 2 Foot Riser Nut Wheel Axle Bolt Wheel Axle Foot Riser Support Anti Sink Plate Rubber Feet Foot Washer Foot Bolt Wheel Washer Wheel Wheel Nut Handle Handle Grip a 4 oo oo oa BRI O 1 1 15 2 lt 2 3 Mounting Instructions for eZG3500 Refer to Figure Below 1 Attach the handle bars to the middle of the generator frame where specified in the figure below Tighten the bolts 14 and nuts 7 to the upper frame of the generator 2 Attach the two peg stands at the bottom of the frame of the genera tor Tighten the two bolts 6 and two nuts 7 to the lower frame of the generator 3 Place the two wheels 5 on the wheel axle 4 and then secure the washer 8 using the split pin 9 to the wheel axle 4 4 Attach the wheel axle 4 to the bottom of the generator frame Align the bolts 6 with the holes on the bottom of the generator and fasten tightly with the nuts 7 provided 16 17 16 18 19 20 hergizer
10. ak after the generator has been running move to fresh air RIGHT AWAY See a doctor You could have carbon monoxide poisoning 10 Chapter 2 Learn About Your Generator This section will show you how to identify key parts of your generator Going over the terminology below will make sure we re on the same page 2 1 Identification of Components Fuel Gauge Frame Bolt Fuel Cap Front Tank Support Power Choke lever Control Panel Engine Handle Control Panel Assembly Alternator Plate Oil Dipstick Recoil Starter Handle Wheel Assembly Engine Plate Anti Sink Plate Frame Fuel Gauge Rear Tank Support Accessory Mount eZG cries On Off Switch Low Oil Light 120 240V AC Outlet Voltage Switch 120V 240V 13A AC CA Voltage Switch Interrupteur tension 120V 13A 120V AC Dual Outlet AC Receptacle CSA Certified or cUL Listed Type L14 30R AC Breaker Ground Mounting Secured to control panel by screws and nuts with mounting metal bracket Remarks Provided with 0 5 mm epoxy fiberglass board underneath receptacle to ensure 12 7mm Electrical spacing between bare live parts and the control panel overall 13 mm by 60 mm Note The following markings appear adjacent to the receptacle MAX 13 A hergizer 2 55200 12 208 Essence sa eo Spy amp 9 Hot Surface Surface Chaude S Keep clear of exhaust
11. aw it will be necessary to disconnect one of the 1500 W heaters 1 Turn off the switches of devices before before connecting them to your generator 2 Insert the plug of the device into your generator based on its voltage requirements Your eZG3500 generator includes two 2 120V AC outlets and one 1 120 240V AC outlet for power specific appliances such as an oven or washer dryer Be sure the Voltage Switch is appointed to the outlet type that you require 3 You can now turn your devices on and use them Power On To stop the engine in an emergency turn the engine switch OFF Always connect the generator to the ground terminal to prevent electrical shock Energizer 4 3 Stopping Your Generator 1 Turn off all of the connected devices Let your generator run for a few minutes to cool down Power Off 2 Stop the generator by pressing and holding the engine switch in the off position until the generator stops 3 Rotate the fuel lever to the off position horizontal eZG cios Chapter 5 Maintaining Your eZG3500 Generator Proper maintenance ensures safe economical and trouble free operation Improper maintenance may cause the generator to malfunction and can lead to serious injuries Contact Energizer Power Customer Support if you have any maintenance questions 5 1 Maintena
12. check the level 2 Hefuel if level is too low Tighten the fuel tank cap securely after refilling Refer to Figure below Gasoline is highly flammable and explosive under certain conditions Refuel in a well ventilated area with the engine stopped Do not smoke or allow open flames or sparks in the area where the generator is being refueled or where gasoline is stored Do not overfill the tank Be careful not to spill fuel when refueling Wipe up any spilled gasoline and let the area dry before starting the engine Gasoline substitutes such as gasohol are not recommended They may be harmful to the fuel system components Energizer B 3 3 Check the Air Filter 1 Loosen the knob and remove the air filter cover Remove the air filter element and observe for cleanliness 2 Clean the air filter element with soap and water or solvent Squeeze dry and then soak in clean engine oll Squeeze out all excess oil and reinstall Replace the element if it is damaged Check the air filter using the maintenance schedule Always inspect air filter before using the generator Clean Air Filter every 3 months or after 50hrs of operation according Section 5 4 Cleaning the Air Filter Filter Filter cap 20 Chapter 4 Using Your eZG3500 Generator DANGER CARBON MONOXIDE Using a generator indoors WILL KILL YOU IN MINUTES Generator exhaust contains high levels of carbon
13. ean and maintain the equipment Operate the generator according to instructions for safe and dependable Service Read user manual carefully before operating this product Failure to do so may result in serious harm to the user and to the equipment Before operating the generator read the user manual carefully Otherwise it may result in personal injuries or equipment damage Never run the generator in an enclosed area to avoid harm from exhaust emissions of a poisonous carbon monoxide gas Be careful not to touch the exhaust system compressor pump or discharge tubing during operation due to risk of burns Pay attention to the warning labels The engine exhaust system will become heated during operation and remain hot immediately after the engine is stopped Gasoline is a highly flammable and explosive liquid Refuel in a well ventilated area with the engine stopped When refueling the generator keep it away from cigarettes open flames smoke and or sparks Connections for standby power to a building s electrical system must be done by a qualified electrician and must comply with all applicable laws and electrical codes Improper connections may cause serious injuries to electrical workers during a power outage and when the utility power is restored the generator may explode or cause fires Place the generator at least 3 feet away from buildings or other equipment during operation Run the generator on a level surface Tilting the
14. ed or replaced at no cost including diagnosis and replacement parts LIMITED WARRANTY PERIODS Recreational and Residential use Two Years Limited e 15 Year Parts and Labor 2 Year Parts only Commercial use 6 months limited parts and labor This limited warranty begins at the initial time of retail purchase and covers manufacturer s defects caused by a defect in components or workmanship during the three 3 Year period The warranty coverage is continual from the initial date of purchase and does not restart at anytime under any circumstances This limited warranty is valid for residential or recreational applications only and only when the generator receives all necessary preventative maintenance as described in the Energizer Generators User Guide The repair or replacement of a generator will take place within a reason able period of time during normal business hours All repair and replacement parts shall be warranted for 90 days after the initial date of installation or purchase LIMITATION OF REMEDIES AND DISCLAIMERS Midland International Inc disclaims any responsibility for loss of time or use of the generator in a recreational vehicle or any vehicle in which the generator is installed transportation commercial loss or any other incidental or consequential damage Any implied warranties are limited to the duration of this written warranty THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE OF AND IN LIEU OF ALL 2
15. enerator Energizer i ENCIGIZE C Sena ENCIGIZEL
16. ft side of your generator it is attached to the bottom of the fuel tank 2 If the engine is cold push the choke lever into the on closed position You can find the choke lever above the air filter cap on the left side of your generator 3 Disconnect all devices from the outlets on the generator panel Then press the engine switch to the HUN position 4 Grasp the recoil stater handle and pull it until the generator starts Do not allow the recoil starter to snap back Return it slowly by hand 5 Push the choke lever to the OPEN position as the engine warms up choke is used to provide the proper air fuel mixture when the engine is cold Choke Off Open 2 lt 4 2 Using the EZG3500 with your Appliances After starting the eZG3500 you can connect your devices to it If you want to use the 120V outlets be sure to move the Voltage Switch is in the right position Before starting make sure that you know what you are able to power with your Genera tor Here s how you can decide Add the watt ratings of all the loads that the generator set will be powering at the same time Make sure that total wattage will not exceed the generator rating EXAMPLE A generator set rated 5000W can power two 1500W heaters a 900W circular saw a 500W drill and a 100W light at the same time 4500W combined However to operate a second 900W s
17. generator may result in fuel spills Know how to stop the generator quickly and understand operation of all the controls Never permit anyone to operate the generator without proper instructions Keep children pets and machinery with rotating parts away during operation Do not operate the generator in rain or snow Do not allow any moisture to come in contact with the generator Do not touch the spark plug while the engine is operating or shortly after the engine has been shut down 1 2 Understanding AC Safety Before connecting the generator to an electrical device or power cord Make sure that everything is in proper working order Faulty devices or power cords can lead to an electrical shock Turn off the generator immediately if the device begins to operate abnormally Then disconnect the device and investigate the problem Make sure that the electrical rating of the device does not exceed that of the generator If the power level of the device is between the maximum output power and the running power of the generator the generator should not be used for more than 30 minutes The connections from the generator to the household power supply should be done by professional electrical technicians Improper connections may lead to a fire hazard or damages to the generator set AC Receptacle CSA Certified or cUL Listed 1 3 Safety while Maintaining Your Generator After any maintenance is performed wash immediately using soap and
18. gestion submersion or external water damage 5 Damage or non performance caused by operation of the genera tor set in a marine application 6 Damage caused by operation with improper fuel or at speeds loads conditions or modifications contrary to published specifications 7 tems not supplied by Energizer including but not limited to starting batteries battery cables external wiring fuel lines filters etc refer to exclusions 8 Repairs made during the warranty period without first obtaining a case number from Energizer Batteries supplied with any generator product should be considered a bonus item and not covered by warranty Batteries can be damaged by shock shorting terminals heat acid spillage and a number of other factors that cannot be controlled after they have left our facility It is the customer s responsibility to take great care when handling a battery so no spillage of acid will occur and cause corrosion damage caused by battery acid is not covered under this warranty Energizer Warranty Claim Procedure Warranty service must be performed by one of our authorized service dealers If you feel your generator is malfunctioning due to a defect or misuse simply contact our customer support center for technical advice a warranty claim or general information Warranty service operation assistance and product support is provided by Energizer Contact us at the following numbers PRODUCT REGISTRATION Prod
19. monoxide CO a poisonous gas you cannot see or smell If you can smell the generator exhaust you are breathing CO But even if you cannot smell the exhaust you could be breathing CO NEVER use a generator inside homes garages crawlspaces or other partly enclosed areas Deadly levels of carbon monoxide can build up in these areas Using a fan or opening windows and doors does NOT supply enough fresh air ONLY use a generator outdoors and far away from open windows doors and vents These openings can pull in generator exhaust Even when you use a generator correctly CO may leak into the home AL WAYS use a battery powered or battery backup CO alarm in your home If you start to feel sick dizzy or weak after the generator has been running move to fresh air HIGHT AWAY See a doctor You could have carbon monoxide poisoning 41 Starting Your Generator Before using generator a ground wire must be connected to the ground terminal The Ground terminal is located on the Front Panel Before using the ground terminal consult a qualified electrician Do not use the choke if the engine is warm or if the air temperature is higher than 50 F 10 C We know you re excited to get using your generator Please be sure to follow the startup instructions below thoroughly to ensure the best lifespan for your generator Energizer i 1 Rotate the fuel valve lever to ON position Vertical position his is located on the le
20. n control system may include such parts as the carburetor or fuel injection system the ignition system and catalytic converter Also included may be hoses connectors and other emission related assemblies 2 lt EMISSION CONTROL SYSTEM WARRANTY PARTS SYSTEMS COVERED IN WARRANTY PARTS DESCRIPTION Carburetor assembly includes starting enrichment system En Fuel Metering gine temperature sensor Engine control module Fuel regulator Intake manifold Fuel Tank Fuel Cap Fuel Hoses Vapor Hoses Carbon Canis Evaporative ter Canister Mounting Brackets Fuel Strainer Fuel cock Fuel Pump Fuel Hose Joint Canister Purge Hose Joint Air Induction Air filter housing Air filter element Flywheel magneto Ignition pulse generator Crankshaft position Ignition sensor Power coil Ignition coil assembly Ignition control mod ule Spark plug cap Spark plug Crankcase Emission Control Crankcase breather tube Oil filler cap Tubing fittings seals gaskets and clamps associated with Miscellaneous Parts 9 9 3 B these listed systems Note This list applies to parts supplied by Midland Power Inc and does not cover parts supplied by the equipment manufacturer Please see the original equipment manufacturer s emissions warranty for non Midland Power Inc parts Consumable parts are covered up to a maximum of 30 days See the Maintenance Schedule in the owner s manual Energizer Warranty Registration Instruc
21. nce Schedule EVERY EVERY EVERY EVERY Item Task Daily 20 50 100 300 HOURS HOURS HOURS HOURS General Inspection Inspect Oil Level Engine Air Filter Sediment Inspection amp Spark Plug Cleaning Replacement Valve Olear Inspection amp ance Adjusting Combustion Inspection amp Chamber Adjusting Fuel Tank and Fuel Line Clean every two months replace if necessary For first use of the generator 5 2 General Inspection Tips 1 Look for fuel leaks around the fuel tank fuel hose fuel valve and carburetor Close the fuel valve and repair leaks immediately 2 Look and listen for exhaust leaks while the engine is running Have all the leaks repaired before continuing operation Energizer 3 Check for dirt and debris and clean as necessary 4 Check the engine oil level and add oil as necessary Do not use gasoline or low flash point solvents for cleaning They are flammable and could explode under certain conditions 5 3 Cleaning The Air Filter Using gasoline or other flammable solvents can cause a fire or explosion Do not operate this product without an air filter 1 Hotate the knob counterclockwise to release 2 Lift the filter cap to remove from the filter 3 Remove the foam filter o 7 0 40 Knobs Filter Filter cap 4 Ifthe foam filter is dirty clean it in warm soapy water rinse and allow it
22. quipped with an Automatic Voltage Regulator which ensures a con stant voltage and present a waveform similar to what you get from the city power grid They are an improvement over basic generators but not as effective at safely running sensitive electronics as our inverter generators which can produce almost perfect sine waveforms Therefore powering some sensitive electronics with this generator is not recommended since it will risk damage the electrical componentry and can cause a risk of damage 29 2 lt 6 0 Troubleshooting Common issues can be fixed by following the instructions in this guide If the unit will not function after following these instructions contact technical support before attempt ing to use or repair the product ISSUE CAUSE ACTION Engine cranks Replace with recommended oil slowly Disconnect load while starting Engine is not Fully open fuel valve starting Remove clean or replace spark plug Black exhaust Clean air filter Contact customer service Reconnect or repair cable Engine has dif Remove clean or replace spark plug ficulty idling Move generator to a level surface Replace the filter Remove all loads reset breaker and check No AC Output Tripped AC circuit breaker loads for defects Do not exceed genera tor rating 30 Energizer Chapter 7 Specifications EZG3500 Rated AC Output Power W 3000W cc lt m Max AC Output Power W 3500W 2 o 1 Phase Rated AC
23. tions Ownership must be registered with Energizer Power Equipment in order to ensure continued warranty and service support Please fill out the registration card below and mail it along with a copy of your receipt and the original UPC barcode from your product packaging The store date of purchase and product purchase should be clearly visible on the receipt copy You may also register online by visiting our website www energizergenerators com If you wish you can confirm your registration by calling customer service at or by email at supportQenergizergenerators com Please allow one week for mail delivery and processing PLEASE MAIL ALL ITEMS TO Midland Power Inc Product Registration 3 6 Magnetic Drive Toronto ON M3J 2C4 Canada Energizer Warranty Registration Card Existing Owner Information First Name Last Name Company Street Name and Number City Postal Zip Code Province State Phone Number Other Contact Number gt Email Product Information eZG 3500 Model Name Serial Number can be found on the Generator or on the exterior of the packaging Initial Date of Purchase Warranty Expiration Date of Transfer Add 2 years to initial date of purchase eZG cios hergizer 38 Ownership and Warranty Transfer Instructions Changes in ownership must be registered with Energizer Power Equipment in order to ensure contin
24. uct registration is required for product support and warranty coverage The owner s registration found in the user manual can be completed and mailed You can also register Online at www energizergenerators com Proof of purchase may be required for warranty claims Keep a copy of the original receipt UPC code and serial number with this manual Customer Service 1 877 528 3772 toll free www energizergenerators com OUR WARRANTY RIGHTS AND OBLIGATIONS California The California Air Resources Board and Midland Power Inc are pleased to explain the emission control system warranty on your Midland Power Inc engine In California new spark ignited small off road equipment engines must be designed built and equipped to meet the State s stringent anti smog standards Other States U S territories and Canada In other areas of the United States and in Canada your engine must be designed built and equipped to meet the U S EPA and Environment Canada emission standards for spark ignited engines at or below 19 Kilowatts All of the United States and Canada Midland Power Inc must warrant the emission control system on your power equipment engine for the period of time listed below provided there has been no abuse neglect or improper maintenance of your power equipment engine Where a warrantable condition exists Midland Power Inc will repair your power equipment engine at no cost to you including diagnosis parts and labor Your emissio
25. ued warranty and service support Warranty support cannot be provided without registration from original date of purchase and after transfer of ownership This transfer form must be completed on or before the date that ownership change takes effect Warranty coverage continues from original date of purchase and is not extended by transfer of ownership hergizer Existing Owner Information First Name Street Name and Number Postal Zip Code Other Contact Number New Owner Information First Name Street Name and Number Postal Zip Code Other Contact Number Product Information Model Name Initial Date of Purchase eZG 3500 Last Name Province State Fax Number Last Name Province State Fax Number Transfer of Ownership and Warranty The serial number can be found on the Generator or on the exterior of the packaging Company City Phone Number Email Company City Phone Number Email Serial Number Warranty Expiration Add 2 years to initial date of purchase Date of Transfer NOTE Transfer of ownership does not act as a warranty extension The original 2 Year Warranty is effective as of the Initial Date of Purchase and continues after ownership has transfered New owners should be made aware of expired or remaining coverage Enjoy Be sure to check energizergenerators com monthly for updates regarding your g
Download Pdf Manuals
Related Search