Lifetone HLAC151 manual
Contents
1. 2 Remove the battery door located on the back of the clock Remove battery door 3 Insert 4 D cell alkaline batteries Install 4 D Cell matching the polarity and 2 Alkaline Batteries Plug In Bed Shaker signs in the open compartment optional equipment The word TEST should appear on the screen A 4 Replace battery door securely 5 After installing the batteries plug the Lifetone HL into the electrical outlet closest to your bedside location Do not use a switched outlet 6 The word TEST will begin flashing The Lifetone HLAC151 will say Press the red button to begin 7 Press and release the red TEST SILENCE button on the back of the clock The word TEST will stop flashing and the HLAC151 will say Please wait 8 After about 30 seconds the word TEST will begin flashing again Your Lifetone HLAC151 will say At the tone test your smoke alarm That indicates that the HL is ready to begin the setup test NOTE The batteries are for backup in the event of a power outage only The Lifetone HL is not meant to run on batteries alone for long periods of time d English C SMOKE ALARM SETUP TEST For your safety the Setup Test with your smoke alarm is an essential part of setting up your Lifetone HL This important test will determine if your existing smoke alarms are of the T3 type and compatible with your Lifetone HL ALWAYS ASK FOR ASSISTANCE2. message and an AC power plug icon will flash The red AC power indicator located on the front left corner will not be lit 2 The clock will operate for a minimum of 7 days on battery backup and the emergency alarm will still be able to sound for at least 4 minutes 3 The wakeup alarm will sound once at the proper time once during the first 24 hours without AC power If the power outage lasts more than 24 hours and you wish to use the wake up alarm again during that same extended outage remove and reinsert the batteries and conduct the set up as described in section VI Smoke Alarm Setup Test 4 Normal operation including the wakeup alarm will resume when AC power is restored LIMITED WARRANTY Lifetone Technology Inc Lifetone the maker of Lifetone brand products warrants that for a period of two 2 years from the date of purchase this product will be free from defects in material and workmanship Lifetone at its option will repair or replace this product or any component of the product found to be defective during the warranty period Replacement will be made with a new or repaired product or component If the product is no longer available replacement may be made with a similar product of equal or greater value This is your exclusive warranty English 14 A buyer of this product may have the right to have it serviced or repaired during the warranty period The warranty period will be extended for the nu
3. is visible on the screen your wake up alarm is active OT Press the ON OFF button on the top of the clock to make the bell icon disappear and the wake up alarm is not active If active the low pitched wake up alarm will sound as an intermittent beep not a T3 signal The time of day will flash on the display and if a bed shaker is attached it will vibrate continuously 6 Pressing the SNOOZE LIGHT button on top of the clock will temporarily stop the alarm and it will sound again 10 minutes later The bell icon will flash during that time Or you can press ON OFF to stop the alarm It will go off again 24 hours later 7 You can adjust the volume of your wake up alarm to sound Low or Hi The HI LO switch is located on the top of the Lifetone HL During a fire emergency the alarm volume will automatically switch to high When you need to change your wake up time press and hold SET ALARM until the wake up hour is flashing and then repeat the steps above S ANI TITT N ZG F TROUBLESHOOTING ERROR MESSAGES PAN Bed Shaker If the display shows beds a flashing bed Q 5 nin L shaker icon and a low pitched tone is coming from the E30 04 Lifetone HL make sure the bed shaker is completely plugged Q fy p a MIL UTE US in If this continues the bed shaker may not be working Bed shaker ERROR Call Customer Service at 1 800 648 7923 for assistance Batteries If the display shows BATT the ba
4. WHENEVER YOU ARE UNABLE TO PROPERLY AND SAFELY ACTIVATE YOUR EXISTING SMOKE ALARMS DURING THE SMOKE ALARM SETUP TEST IF YOU HAVE AMONITORED SMOKE OR FIRE ALARM SYSTEM CONTACT YOUR SERVICE AND TELL THEM YOU ARE TESTING YOUR SYSTEM WHEN YOU ARE FINISHED CALL THEM AGAIN TO TELL THEM YOUR TESTS ARE COMPLETED 1 Your HLAC151 will say At the tone test your smoke alarm and then it will sound a tone Locate the most distant smoke alarm you want detected If you have an interconnected alarm system use the nearest smoke alarm It is recommended you use an alarm that is easy to reach and activate avoiding alarms on high ceilings 2 Press and hold the test button on the smoke alarm until the Lifetone HL alarm sounds At least two smoke alarm TI T3 cycles groups of 3 beeps are required You may need as many as six in a row if there is excessive background ie noise or your alarms are distant Vries 3 If the test is successful your HLAC151 will sound its alarm the bed shaker will vibrate and FIRE will flash on the screen If the test was not successful use a nearer smoke alarm and try again You may repeat the test as many times as necessary until you have a successful result PULSING tant agm Your Lifetone HALC151 will say At the tone test your smoke alarm every 5 minutes until you are successful 4 After a successful test the HLAC151 will say Now set the clock and 12hr will flash o
5. month first or day first in your date display a If you prefer the month first simply press SET CLOCK to go on b If you prefer the day first use the or button then press SET CLOCK 6 E for English will be flashing at lower right Press SET CLOCK for English If you prefer Spanish S or French F for the day of the week use or to select and press SET CLOCK 7 The clock has been successfully set 8 If the wake up hour at lower left is flashing press SET CLOCK again The little bell icon means that the wake up alarm will sound at that hour Press the ON OFF button once to disable the wake up alarm 9 The clock will show the day of the week to the right of the date If you prefer to display the year press SET CLOCK I When you need to reset the clock for daylight PRoniofF Hi LO SET ALARM SET CLOCK savings time press and hold SET CLOCK F OO 5 until the flashing 12 hr appears and repeat the steps above 9 English E SETTING THE WAKE UP ALARM WAKE UP ALARM CONTROLS ALARM VOLUME ALARM TIME SETTING ALARM PR onorr HI LO SETALARM SET CLOCK ENABLE sr 000080 WAKE UP HOUR MINUTE Press and hold SET ALARM until the wake up hour is flashing The wake up hour is flashing Press or to select the hour then press SET ALARM oO ND The wake up minute is flashing Press or to select the minute then press SET ALARM 4 If the bell icon
6. EQUENTLY ASKED QUESTIONS scsscsssssssssstsntsssstsatsntitsatistsatistutiatisseissatees 14 X LIMITED WARRANTY cca sssedeurinractraiausiatsaniatindundmamiatancanehinunnestit 14 XI RECOMMENDED LOCATIONS FOR SMOKE ALARMS ssssssssssssssssssssnssesssseves 16 1 English I INTRODUCTION Thank you for purchasing the Lifetone HL Bedside Fire Alarm and Clock It is an important part of your family s safety plan The Lifetone HL is not a smoke detector and does not detect smoke Instead it detects the alarm sounds made by smoke alarms and smoke alarm systems that are UL listed or Intertek listed to and compliant with the UL 217 US or ULC 5531 Canada standard T3 alarm signal YOU MUST HAVE PROPERLY INSTALLED UL 217 OR ULC 531 LISTED AND COMPLIANT T3 SMOKE ALARMS IN YOUR HOME BEFORE THE LIFETONE HL BEDSIDE FIRE ALARM AND CLOCK WILL OPERATE CORRECTLY What is UL UL is Underwriters Laboratories a global safety standards organization that defines signals of this kind as well as standards for a wide range of commercial products The 217 or S531 identifies the applicable standard for smoke alarms What is a T3 smoke alarm The UL 217 or ULC 5531 compliant T3 cc pattern is an alarm signal that is on and off for 7 second three times in succession followed by a 17 second pause An on off representation of three cycles of that sound looks like this N N N N N N N N N i S amp S S amp S amp YF
7. G Because there are environmental acoustic variables involved such as background noise levels and distance to your smoke alarms and variations in some smoke alarm T3 signal periods and timing the setup test result cannot guarantee that your smoke alarms will always be detected within 30 seconds in the event of an emergency See the instructions and section G TESTING THE LIFETONE HL for details IV OPERATING INSTRUCTIONS READ AND FOLLOW THESE INSTRUCTIONS BEFORE OPERATING YOUR LIFETONE HL BEDSIDE FIRE ALARM AND CLOCK See Warnings in Section Ill of the User s Manual 1 Make sure your existing smoke alarms are UL listed and compliant T3 smoke alarms You must have properly installed UL listed and compliant T3 smoke alarms in your home before the Lifetone HL Bedside Fire Alarm and Clock will operate correctly Read and follow the instructions and warnings that accompany your existing smoke alarms If you are unsure whether your existing smoke alarms are UL listed and compliant ask the manufacturer of those products or your local fire official about your smoke alarms Investigate further until you are satisfied that your existing smoke alarms are UL listed and compliant T3 smoke alarms Do not use the Lifetone HL Fire Alarm with First Alert talking alarms made prior to 24 October 2011 Some may pass the setup test but have a variable length T3 emergency signal that is not UL 217 compliant UL 217 6th Ed 34 3 2b and cannot be
8. L g S E amp YF L g i OFF OFF OFF OFF OFF OFF i OFF OFF OFF FOUR SECONDS FOUR SECONDS FOUR SECONDS And it sounds like this beep beep beep pause then beep beep beep pause and this continues Some alarms may have voice messages in the pauses Those alarms will be compatible if in a true emergency the voice messages are less than 17 seconds long and fitted into the 17 second pause or the voice message follows eight 8 consecutive T3 signals each 4 seconds in duration The Lifetone HL Bedside Fire Alarm and Clock will detect this T3 pattern and activate a loud low 520 Hz multiple frequency alarm and activate the Lifetone Bed Shaker optional equipment Scientific research has proven the 520 Hz alarm to be more effective at awakening and alerting people with hearing loss Together the Lifetone HL alarm and the optional Lifetone Bed Shaker provide effective awakening and alerting for those with normal hearing loss that comes with age or exposure to loud noise and the deaf The Lifetone HL Bedside Fire Alarm and Clock Lifetone HL Fire Alarm is an assistive alerting device intended for use in a residence by individuals with hearing loss or the deaf It is to be placed in a nighttime sleeping area next to a bed The Lifetone HL Fire Alarm will detect the T3 emergency signal given by existing properly placed UL 217 listed and UL 217 or ULC 5531 compliant smoke alarms When a smoke alarm is detec
9. TY TEST TO BE SURE THE MOVED OR NEW SMOKE ALARMS ARE PROPERLY DETECTED 2 ANNUAL TESTS Replace the batteries in your Lifetone HLAC every year and follow the manufacturer s recommendations for replacing batteries in your smoke detectors Then conduct the weekly self test the audio sensitivity test and then this functional test e The functional test This test which simulates an emergency is recommended by Lifetone to demonstrate that the HLAC and your smoke alarms work together The test requires at least seven consecutive uninterrupted T3 cycles of 4 seconds duration each If your alarm does not produce at least seven T3 cycles in response to the test button contact your smoke alarm manufacturer and inquire about a safe functional test procedure with a UL listed simulated or imitation canned smoke designed specifically for the purpose Follow your manufacturer s instructions ald English The HLAC must be in normal operating mode and NOT displaying the icon Initiate the smoke alarm emergency signal for at least 7 consecutive T3 cycles by holding down the smoke alarm test button or by using the simulated smoke if and as directed by the manufacturer During a functional test the HLAC will normally respond in six to eight T3 cycles If background noise levels are high or the smoke alarm is distant as many as ten or twelve T3 cycles may be required When the HLAC sounds its alarm the function test is successful Silence it wit
10. a lifetone TECHNOLOGY LIFETONE HL Bedside Fire Alarm amp Clock 200000 o o o gt o gt o IGG D 66 gt e 20900000 SCC eee 99006066 0 0 o o Oo 0 o gt 92906656 See User s Manual MODEL HLAC151 SIGNALING Lifetone Model No HLAC151 Single and or Multiple station Smoke Alarm Accessory 524639 UTGT UTGT7 UUKC Low frequency sounder Listed by UL to UL 217 C UL US and ULC 531 for use with residential smoke alarms and commercial notification appliances in US and Canada and listed to UL 1971 when used with bed shaker LISTED NFPA 72 compliant editions 2010 2013 LIFETONE HL Bedside Fire Alarm amp Clock a lifetone TECHNOLOGY USER S MANUAL MODEL HLAC151 PLEASE READ THIS USER S MANUAL COMPLETELY AND THOROUGHLY BEFORE BEGINING L TIN TRUS TION EEE 2 II LIFETONE HL BEDSIDE FIRE ALARM AND CLOCK cssssssssssstssssssnsntitsatitinie 3 A CONTROLS AND DISPLAY nmssessesvvsesssvssessrssssessessrsessesessessessrsessessessessesseenn 3 B FEATURES ssovssessrsevststesevstssessvsessessersessersessessesessessesessessesesseseessessessersessessen 3 Ill WARNINGS nnnsnssvssssrsrssssrsersessesevsessessssessessesessessessessessessesseseersessessrsessessensene 4 IV OPERATING INSTRUCTIONS msesvesessssvsstvssrrsessesersessessrsessessersessesseessessersessesssn 5 V BEFORE INSTALLING nssssevssssevssssssvsesssssssessrssrsessesessessesessessesessesses
11. arm and in a continuous manner for the wake up alarm A Silence button that can silence the emergency alarm temporarily If the smoke alarm is detected again the emergency alarm will sound again within 10 15 seconds In the event of a power failure the Lifetone HL can operate in battery backup mode for a minimum of 7 days and still provide emergency alarm signals As a safety feature when AC or battery power is first applied the Lifetone HL will require a test of your installed smoke alarms The model HLAC151 provides voice prompts to assist with the set up and a provision for periodic audio sensitivity testing with your smoke alarms to demonstrate that they are still detected if you move or replace them 3 English B FEATURES continued 8 If the optional Lifetone Bed Shaker is used and becomes unplugged the word bedS and a flashing bed shaker icon will appear on the screen and a low frequency chirp will sound every 5 seconds 9 If AC power is lost the red power LED located on the front left corner will go out In the left corner of the display an ERROR message and an AC plug icon will flash 10 If the batteries are missing or too low to support 24 hours of battery operation the word BATT will appear on the screen in large text a low pitched chirp will sound and the bed shaker will twitch at one minute intervals If the batteries are low replace them immediately to ensure yo
12. d levels and obstruct the emergency signal given by the product which may result in personal injury or death English 4 Ill WARNINGS continued WARNING ALWAYS face the Speaker towards the pillow Improper orientation of the Lifetone HL Fire Alarm to the user may obstruct proper operation which may result in personal injury or death WARNING Do not obstruct the raised Microphone Grille and Dust Protector Covering or blocking this component may obstruct proper operation which may result in personal injury or death WARNING Always use the batteries specified by this User s Manual Do not use rechargeable batteries Use of different batteries may damage the product or cause it to fail to detect a signal from an activated smoke alarm which may result in personal injury or death WARNING Do not use the Lifetone HL Fire Alarm where the humidity exceeds 95 or where the surrounding temperature is lower than 32 F 0 C or higher than 120 F 49 C Constant exposure to high or low temperatures or excessive humidity may obstruct the product s intended signaling performance which may result in personal injury or death WARNING This product contains a chemical known to the State of California to cause cancer birth defects or other reproductive harm WARNING Do not ignore any emergency alarm Failure to investigate for smoke or fire after having received an emergency signal may result in personal injury or death WARNIN
13. e alarm first and then the Lifetone HLAC DO NOT IGNORE ANY ALARM ESPECIALLY A REPEATED ALARM EVACUATE AND THEN EVALUATE IT FROM A PLACE OF SAFETY B TEST SILENCE BUTTON 1 The TEST SILENCE button on the back of the clock is not a reset button After set up and in normal operation it is used to silence an active fire alarm or to start a manual test 2 Do not use the TEST SILENCE button to stop a wake up alarm It will stop but then the HL will start a manual test When the manual test fire alarm ends the wake up alarm will resume Use the snooze bar or the alarm on off button instead CLOCK LIGHT PANEL Press the SNOOZE LIGHT button to change the brightness level The display backlight has three levels of brightness high medium and off If AC power is lost the backlight will be off Press SNOOZE LIGHT and the display will light for 5 seconds D OPTIONAL BED SHAKER USE AND CARE 1 The Lifetone Bed Shaker may be placed under the mattress pad or the pillow wW N gt O 2 It is water resistant but not waterproof It may be cleaned periodically with soap and a damp cloth Do not submerge the bed shaker in any liquid 3 It has a thermal switch to turn it off if it gets too warm It will reactivate after it cools down and continue to vibrate if the alarm is still active Do not try to open it 4 The bed shaker is electronically supervised Do not use any other bed shaker with the Lifetone HL Doing s
14. eeping room the distance measured along a path of travel 3 On every level of a dwelling unit including basements 4 On every level of a residential board and care occupancy small facility including basements and excluding crawl spaces and unfinished attics 5 In the living area s of a guest suite 6 In the living area s of a residential board and care occupancy small facility NFPA 72 at 11 5 1 1 2007 Ed A 11 4 Family Escape Plan There often is very little time between the detection of a fire and the time it becomes deadly This interval can be as little as 1 or 2 minutes Thus this Code requires detection means to give a family some advance warning of the development of conditions that become dangerous to life within a short period of time Such warning however could be wasted unless the family has planned in advance for rapid exit from their residence Therefore in addition to the fire warning equipment this Code requires exit plan information to be furnished Planning and practicing for fire conditions with a focus on rapid exit from the residence are important Drills should be held so that all family members know the action to be taken Each person should plan for the possibility that exit out of a bedroom window could be necessary An exit out of the residence without the need to open a bedroom door is essential NFPA 72 at A 11 4 2007 Ed A 11 8 3 Are More Smoke Alarms Desirable The required nu
15. end to the notifications on the display screen Smoke or fire emergency signals appear there Other visual signals indicating normal operation and errors are shown on the screen With the exception of the time of day colon any flashing symbol is intended to attract your attention 1 English 6 V BEFORE INSTALLING The Lifetone HL cannot awaken or alert you to smoke or fire if your existing smoke alarms do not operate or if they do not have the UL listed and compliant T3 emergency signal The Lifetone HL WILL NOT OPERATE with smoke alarms that do not use the UL 217 compliant T3 pattern alarm signal When you power up the Lifetone HL you will be required to perform a Smoke Alarm Setup Test If your home does not have T3 smoke alarms the Smoke Alarm Setup Test will not be successful You must replace the older alarms with current UL listed and compliant T3 smoke alarms before your Lifetone HL will operate correctly Refer to your smoke alarm s user manual to determine when to replace your smoke alarms or their batteries VI INSTALLATION AND ACTIVATION A LOCATION OF THE LIFETONE HL 1 Place the Lifetone HL next to your bed and 3 feet from where your head will be 2 Face the speaker toward the pillow B POWERING THE PRODUCT 1 If you have purchased the optional bed Zz shaker you may plug it in on the backof Ma go yy meer the clock now or after it has been set up The plug is labeled Bed Shaker
16. gth during the first 32 seconds of an emergency alarm the alarm is not UL 217 compliant UL 217 6th Ed 34 3 2b e Is the Lifetone HLAC screen active If not check the batteries and AC power source for the HLAC the red LED on the front should be lit Make sure the HLAC is not plugged into a switched outlet Has unusually loud background noise been eliminated Make sure the black microphone dome on top is unobstructed e Is the smoke alarm signal distant or obstructed by sound barriers Extreme distance and heavy tightly fitted doors can reduce the smoke alarm sound level Try a closer alarm This will show you what the distance and sound level limits of detection are in your home If you have checked the above and additional smoke alarm setup tests are unsuccessful please contact us at 1 800 648 7923 English 12 VII USING THE LIFETONE HLAC A RECOGNIZING THE HLAC EMERGENCY ALARM SIGNALS 1 The word FIRE will appear and flash on the screen The loud 520Hz alarm will sound for 10 minutes or until it is silenced 2 If an optional bed shaker is attached it will pulse repeatedly with a 1 second on 2 second off pattern This is different from the steady vibration of the wake up alarm 3 If the alarm has been silenced and the patented detector continues to hear a smoke alarm the alarm will sound again within 15 seconds 4 If a nuisance alarm should occur due to cooking smoke silence the smok
17. h the red TEST SILENCE button on the back If the HLAC does not sound its alarm after twelve T3 cycles you may have a non compliant incompatible smoke alarm Call Lifetone customer support at 1 800 648 7923 for assistance A functional test also serves as an audio sensitivity test for a particular alarm but in this case the HLAC must be silenced manually with the red button Note that the HLAC will be in high sensitivity mode for 2 minutes afterward with the icon displayed In order to repeat the functional test with another smoke alarm you must wait for two minutes until the icon disappears H UNSUCCESSFUL SMOKE ALARM SETUP TEST If the HLAC did not flash FIRE and sound an alarm your existing smoke alarms were not detected or are not compatible with the LIFETONE HL Check the following conditions e Is your smoke alarm a UL 217 listed and compliant T3 smoke alarm Beginning in 1999 most residential building codes required UL 217 listed or compliant T3 smoke alarms Alarms manufactured after that were required to meet that standard OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF FOUR SECONDS FOUR SECONDS FOUR SECONDS FOUR SECONDS A T3 signal is a set of three 7 second beeps 2 second apart followed by 17 seconds of silence and that signal is repeated In a true emergency the first 8 cycles must each be 4 seconds long If there are not distinct groups of three pulses or the time between sets of pulses varies in len
18. mber of smoke alarms might not provide reliable early warning protection for those areas separated by a door from the areas protected by the required smoke alarms For this reason the use of additional smoke alarms for those areas for increased protection is recommended The additional areas include the basement bedrooms dining room furnace room utility room and hallways not protected by the required smoke alarms The installation of smoke alarms in kitchens attics finished or unfinished or garages is not normally recommended because these locations occasionally experience conditions that can result in improper operation NFPA at 8 A 11 8 3 2007 Ed Also the California State Fire Marshall s code recommends that Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows A smoke alarm installed in each separate sleeping area in the vicinity of but outside of the bedrooms and heat or smoke detectors in the living rooms diningrooms bedrooms kitchens hallways attics furnace rooms closets utility and storage rooms basements and attached garages Consult your state and municipal codes for additional recommendations and requirements for smoke alarm installation Copyright Lifetone Technology Inc All Rights Reserved 2010 2011 2012 English 16 Doc LTUG151E130802
19. mber of whole days that the product has been out of the buyer s hands for warranty repairs If a defect exists within the warranty period the warranty will not expire until the defect has been fixed The warranty period will also be extended if the warranty repairs have not been performed due to delays caused by circumstances beyond the control of the buyer or if the warranty repairs did not remedy the defect and the buyer notifies the manufacturer or seller of the failure of the repairs within 60 days after they were completed If after a reasonable number of attempts the defect has not been fixed the buyer may return this product for a replacement or a refund subject in either case to deduction of a reasonable charge for usage This time extension does not affect the protections or remedies the buyer has under other laws This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable Keep the original sales receipt Proof of purchase is required to obtain warranty performance Lifetone dealers service centers retail stores and Internet purchase agents selling Lifetone products do not have the right to alter modify or any way change the terms and conditions of this warranty This warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of this product use on improper voltage or current use of rechargeable batteries use cont
20. n the screen 5 If you have a First Alert talking alarm model SCO7 or SCO500 made before October of 2011 see the back of the alarm for the date you must also do a functional test as described in section G TESTING THE LIFETONE HLAC to ensure that the emergency signal from that alarm is compatible If the setup test is not successful after several tries you may have an incompatible smoke alarm Please refer to section H UNSUCCESSFUL SMOKE ALARM SETUP TEST English 8 D SETTING THE CLOCK NOTE If at any time during this process you need to start over press and hold SET CLOCK until the flashing 12 hr appears and repeat the steps below Buttons on the top of the Lifetone HL HOUR MINUTE PR on OFF HI LO SET ALARM SET CLOCK O OOD O YEAR LANGUAGE DAY OF WEEK MONTH OR N DAY FIRST MONTH DAY 1 The 12 hr time display is flashing To select a 24 hour display format press or Then press SET CLOCK to proceed to setting the hour 2 12 00 PM noon will flash Use or to increase or decrease the hour Then press SET CLOCK to set the minute 3 Use or to increase or decrease the minute Then press SET CLOCK to set the year 4 The year 08 will be flashing in the lower right corner Use to increase the year Then press SET CLOCK to proceed to the date setting 5 A small M and D above the month and day numbers will be flashing This is the option for
21. o invalidates any Lifetone Technology warranties or claims 5 If you disconnect the bed shaker the clock will chirp every 5 seconds and display bedS To stop the clock from chirping press the red TEST SILENCE button The Lifetone HL will conduct a brief self test but without the Smoke Alarm Setup Test and then it will be reset to operate without the bed shaker 13 English Vill REGULAR MAINTENANCE A BATTERIES 1 Replace the 4 D cell batteries once a year or more often if power outages occur or a low battery warning occurs 2 Use 4 new D cell alkaline batteries and replace all batteries at the same time B POWER ADAPTER 1 The Lifetone HL includes an AC power adapter The red A aii power light on the front should be lit at all times unless there ran w is a power outage and the unit is operating on its back up batteries 2 No other power adapters should be used Failure to use the Lifetone AC adapter could result in damage or incorrect operation of the Lifetone HL IX FREQUENTLY ASKED QUESTIONS HOW DO I SILENCE THE EMERGENCY ALARM SIGNAL N 1 Press the red TEST SILENCE button for 2 seconds 2 If the Lifetone HL detects a smoke alarm again the alarm will sound within 15 seconds 3 If there is a nuisance alarm due to kitchen smoke silence the smoke alarm first and then the Lifetone HLAC WHAT HAPPENS IF LOSE AC POWER 1 In the left corner of the Display an ERROR
22. onds FIRE will appear on the display and the clock will sound three T3 alarm cycles This demonstrates that the microphone speaker and other electronic components are working properly After the self test is complete the HLAC151 will return to normal operation and display the A icon For two DE ve en minutes it will be responsive to two T3 cycles from your 6 DE smoke alarms If you wish you may now do an audio Saas LILI sensitivity test using your smoke alarms with the SF ASHANTI ma Man Lifetone HLAC151 e The audio sensitivity test To test the audio sensitivity of your HLAC151 with your smoke alarm press the test button on your nearest installed smoke alarm during the 2 minutes that the icon is displayed When the HLAC151 detects your smoke alarm it will sound its lower pitched alarm The alarm will stop by itself after three T3 alarm outputs Go to the next smoke alarm in your home within 2 minutes and press the test button on that one Repeat until all smoke alarms have been tested Note that the two minute period starts over each time a smoke alarm is detected Moving from smoke alarm to smoke alarm and repeating the test will verify that the smoke alarms in your home are working and can also show you what the distance and background noise limits of detection are in your home IF YOU MOVE YOUR HLAC151 OR MOVE OR REPLACE YOUR SMOKE ALARMS CONDUCT THE SELF TEST AND THE AUDIO SENSITIVI
23. or province to province How to Obtain Warranty Service If service is required do not return the product to the original place of purchase In order to obtain warranty service please contact us at 1 800 648 7923 or email customerservice lifetonesafety com To assist us in serving you please have the model number and date of purchase available when calling Manufacturer Lifetone Technology Inc 800 Research Parkway Suite 339 Oklahoma City OK 73104 15 English XI RECOMMENDED LOCATIONS FOR SMOKE ALARMS Make sure your existing smoke alarms are properly placed in your home Your existing smoke alarms will reference and rely upon the National Fire Protection Association s NFPA Standard 72 regarding the number and placement of smoke alarms in your dwelling This information is critical to determine whether you have the correct UL certified and compliant T3 smoke alarms and that they are properly placed in your home The NFPA Standard 72 August 17 2006 and the California Fire Marshall s Code provides in part the following guidance about placement and detection of your existing smoke alarms 11 5 1 1 Required Detection Where required by applicable laws codes or standards for a specific type of occupancy approved single and multiple station smoke alarms shall be installed as follows 1 In all sleeping rooms and guest rooms 2 Outside of each separate dwelling unit sleeping area within 6 4 m 21 ft of any door to a sl
24. rary to the operating instructions and disassembly repair or alteration by anyone other than Lifetone or an authorized service center Further this warranty does not cover Acts of God such as fire flood hurricanes and tornadoes or any batteries other than specified in this User s Manual This product is warranted to be specifically fit for the particular needs of you the buyer If the product is not specifically fit for your particular needs it may be returned to the seller within 30 days of the date of actual receipt by you or completion of fitting by the seller whichever occurs later If you return the product the seller will either adjust or replace the device or promptly refund the total amount paid This warranty does not affect the protections and remedies you have under other laws Lifetone shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty Some states provinces or jurisdictions do not allow the exclusive or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state
25. re Alarm connected to an electrical outlet Check the red power lamp on the front to be sure the unit has not been accidentally unplugged The Lifetone HL is not meant to operate on batteries alone for extended periods of time Do not rely upon the batteries for normal operation The batteries are for backup during power outages 6 Do not plug your Lifetone HL into a switched electrical outlet i e an outlet that is controlled by a wall switch 7 Replace the batteries in your Lifetone HL as needed Replace the batteries at least once a year in your Lifetone HL or more often if there have been frequent or extended power outages The Lifetone HL will give an audio chirp once each minute and flash BATT on the screen to signal low batteries 8 Do not unplug the unit from AC power when you change the batteries As long as the Lifetone HL has AC or battery power it will preserve your setup information so that you don t have to do the setup test again When batteries are changed is also a good time to conduct alarm tests See section G TESTING THE LIFETONE HL 9 Use the correct batteries in your Lifetone HL Fire Alarm Use four 4 D cell alkaline batteries in your product Do not use rechargeable batteries because they may damage your Lifetone HL Fire Alarm 10 Face the display screen toward you The Display screen and speaker must face you to assure proper operation of the product Att
26. recognized by the Lifetone HL Fire Alarm First Alert talking alarms made after that date may have a UL 217 compliant T3 signal and if they do those alarms will be compatible with the Lifetone HL Fire Alarm See section G TESTING THE HLAC for details or call the manufacturer 5 English IV OPERATING INSTRUCTIONS continued READ AND FOLLOW THESE INSTRUCTIONS BEFORE OPERATING YOUR LIFETONE HL BEDSIDE FIRE ALARM AND CLOCK See Warnings in Section III of the User s Manual 2 Test your Lifetone HL Fire Alarm frequently with your smoke alarms Press the red TEST SILENCE button on the back After the Lifetone HLAC151 test fire alarm stops look for the icon on the display Then go to your smoke alarm and press the test button on that This test may identify smoke alarms in your home that are not functioning See section IV G TESTING THE LIFETONE HL for detailed testing instructions 3 Keep noise levels in your home to a reasonable minimum during use Your Lifetone HL Fire Alarm is at its best in a quiet environment next to your bed or ina nighttime sleeping area Excessive noise may mask an emergency signal from your smoke alarms and may increase the amount of time to detect that signal 4 Keep the Microphone Grille and Dust Protector free and clear Do not cover the top of the unit with anything The domed microphone area must be unobstructed to assure proper operation of the product 5 Keep your Lifetone HL Fi
27. seessessessesn 7 VI INSTALLATION AND ACTIVATION m iessessessvsssrstssssesessessessersessessessesessessessessessesn 7 A LOCATION OF THE LIFETONE HL nnnssessssvsressessessessessessessessessessssessessessessessesns 7 B POWERING THE PRODUCT essessvessessesvssesstsrrsessesessessessersessessessesseseessessessen 7 C SMOKE ALARM SETUP TEST nnsesoessvnessesrrsessesevstssersssseserssssessrsessesssessessesseenn 8 D SETTING THE COCK ee 9 E SETTING THE WAKE UP ALARM ssessvssessssrvsessessevsesserssersessesssssessersessessessessesen 10 F TROUBLESHOOTING ERROR MESSAGES scsssssssnsstsnssssstsnsstsstsasintsstisesstsee 10 G TESTING THE LEE NE en 11 H UNSUCCESSFUL SMOKE ALARM SETUP TEST ssssssssssssstsssstsssntsnsstsnsatsees 12 VII USING THE LIFETONE H iissossessssvsstssrsessessesessessessessesessessessessessesseessessesessessen 13 A RECOGNIZING THE EMERGENCY ALARM SIGNALS csssssssssescssssssssssnsssens 13 B TEST SILENCE BUTTON secsssssssssssstsnssnsatsnssntntsatsesstsnatsessssassesssinasnessesasseee 13 C CLOCK LIGHT PANEL csssssssstsnsstsstsssstsstsssistsatsesstiatsntstsatsntatiatsnsstsassssstses 13 D BED SHAKER OPTIONAL AND CARE insssvssvssstestvsessssevstssrsessesessessessssene 13 VIII REGULAR MAINTENANCE scsssssssssssssnsstsntsnistsattsntiatissatisnsstiatinassnatsesssses 14 A BATTERIES niossessessversessersvessessesrrsessesersessessessessessesesseseessessesessessesessessessessesen 14 B POWER ADAPTER EEE 14 IX FR
28. ted the model HLAC151 will give its own emergency signal at a lower frequency 520 Hz which may be heard by individuals with hearing loss The product also gives its emergency signals visually on a display screen and with an optional tactile Bed Shaker either of which may be detected by deaf individuals in their beds The Lifetone HL Fire Alarm is not intended for use in marine watercraft recreational vehicles RVs mobile homes or hospitals English 2 ll LIFETONE HL BEDSIDE FIRE ALARM AND CLOCK A CONTROLS AND DISPLAY OMONSIAUROVLVN gt Microphone grille and dust protector Speaker Must face pillow Clock and Status Display EN Wake Up Alarm and Clock Controls Snooze Light button Test Silence button ro Battery Compartment THIS SIDE TOWARD PILLOW Optional Bed Shaker plug Power Cord Front View 6 TEST SILENCE EN BED SHAKER Top View Back View Power Cord is below the Bed Shaker Plug B FEATURES 1 A patented detection technology that constantly listens for and detects only UL listed and NFPA recommended smoke alarms that emit a UL 217 compliant T3 signal A low pitched alarm sound at 520 Hz that has been shown to be more effective for waking and alerting individuals with hearing loss A tactile alarm is provided in the form of an optional UL listed Lifetone Bed Shaker that vibrates intermittently if there is an emergency al
29. ttery icon SFLASHINGS is flashing on the display and the clock is sounding a low mv 6 T roi pitched chirp every minute the batteries are low or improperly 4 Tt rm I I inserted Remove the batteries and insert them again making sure to match the polarity and signs in the open battery AP BO iiu compartment If this continues the batteries must be replaced Battery ERROR Do not unplug the Lifetone HL when changing batteries Loss of AC power If the Lifetone HL comes unplugged from the wall or there is a power outage the red AC power light on the front of the unit will go out and the plug icon will blink The HLAC is on back up power The batteries will last for seven cumulative days of power outages AC power is off English 10 G TESTING YOUR LIFETONE HL The Lifetone HLAC depends on working UL listed and compliant T3 smoke alarms in your home Testing your smoke alarms and your Lifetone HLAC on a regular basis is the best way to ensure your safety Because test procedures for smoke alarms may vary you must refer to your smoke alarm manufacturer s manuals for descriptions and instructions for testing your smoke alarms There are three ways you can test your HLAC Self test Audio sensitivity test e Functional test 1 WEEKLY TESTS e The self test Press and hold the red TEST SILENCE button for two seconds or until TEST appears on the screen Release the button After 15 to 30 sec
30. ur safety When replacing batteries do not unplug the HLAC151 Keeping it powered during battery replacement will preserve the set up information ICON DESCRIPTION ERROR Generic error message AC Power is unplugged Batteries are low or missing Optional Bed Shaker is unplugged or defective gt Wake up alarm is activated Ill WARNINGS READ AND UNDERSTAND THESE WARNINGS BEFORE INSTALLING AND OPERATING YOUR LIFETONE HL BEDSIDE FIRE ALARM AND CLOCK See instructions in Section IV of the User s Manual WARNING ALWAYS install UL listed T3 smoke alarms in proper locations in your home before operating the Lifetone HL Fire Alarm Failure to verify that all existing smoke alarms are UL 217 listed and UL 217 compliant with this product may obstruct proper operation which may result in personal injury or death WARNING FREQUENTLY TEST the Lifetone HL Fire Alarm to assure its proper operation with your existing smoke alarms Failure to test this product frequently may obstruct its proper operation which may result in personal injury or death WARNING ALWAYS keep noise levels in your home to a maximum of 70 dB or lower Excessive noise levels may obstruct the emergency signals given by your existing smoke alarm to the Lifetone HL Fire Alarm which may result in personal injury or death WARNING DO NOT use the Lifetone HL Fire Alarm with acoustic sound dampening wall or ceiling materials These materials may reduce soun
Download Pdf Manuals
Related Search