User Manual
Contents
1. 2014 SurgeX Electronic Systems Protection Inc surgex com CE SEQ1200i SURGEX energy intelligence SEQUENCER SURGE ELIMINATOR amp POWER CONDITIONER Caution The SEQ1200i series products permit a maximum 16A SEQ1216i models 15A SEQ1215i models 13A SEQ1213i models or 10A SEQ1210i models total output load with a maximum 10A load per outlet Please check and make sure that each load connected to the unit does not exceed 10A Also make sure that the total does not exceed your mains receptacles current limit For safety please plug your SurgeX unit into a fused receptacle T20AL 250v fuse recommended SEQ1200i Series Mode Protection is Live Neutral only if the polarity indicator is illuminated when connected to the mains please replace the plug observing correct polarity Description The SurgeX SEQ1200i is a 230V rack mounted power sequencer incorporating SurgeX power conditioning and surge elimination The single rack space steel enclosure is designed to be installed in a 19 inch equipment rack A total of 10 IEC receptacles are provided on the rear panel Two are always on with the remaining eight configured as four sequenced banks of two receptacles per bank 4 models are available with load capable circuitry and connectivity that conform to AS3112 BS1363 BS546 and CEE7 7 standards The power switch delay time adjustment and status LED s are all on the front panel The always on receptacles wil2. This Limited Warranty does not apply to any product which is defective due to any causes beyond SurgeX s control such as negligence abuse misuse acts of god modifications to the product or third party repair of the product THE LIABILITY OF SURGEX IF ANY AND YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY ALLEGEDLY DEFECTIVE SURGEX INTERNATIONAL PRODUCT SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT IN ACCORDANCE WITH THE TERMS AND CONDITIONS OF THIS LIMITED WARRANTY IN NO EVENT WILL SURGEX BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES 2014 SurgeX Electronic Systems Protection Inc surgex com
3. authorised personnel 8 Servicing is required when the appliance has been damaged in any way including Impact damage power cord supply damage liquid spillages small objects falling into the unit or exposure to moisture In addition please refer to authorised service personnel if the appliance is not operating normally 9 To completely disconnect this equipment from the AC mains disconnect the power plug from the AC receptacle 10 To prevent fire never place the appliance near any naked flame such as a candle 11 This is a CLASS 1 device and shall be connected to a mains socket with a protective earth connection 12 Do not defeat the purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is there for your safety If the plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Management of WEEE Waste Electrical and Electronic Equipment Applicable in member states of the European Union and other European countries with individual nation policies on the management of WEEE The symbol on the product or its packaging indicates that this product may not be treated as regular household waste It should be returned to the retailer where the product was purchased or local mE collection systems should be used to ensure environmentally safe recycling
4. SURGEN energy intelligence E Electronic Systems Protection Inc 0 8001 Knightdale Blvd Sue ied OPERATING MANUAL AND USER GUIDE Knightdale NC 27545 2014 SurgeX Electronic Systems Protection Inc surgex com CE SURGEX energy intelligence IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol CAUTION within an equilateral triangle is intended to RISK OF ELECTRIC SHOCK alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and NNECT ONLY TO MAIN KET WX WARNING co bu SUUS maintenance servicing instructions in the WITH PROTECTIVE EARTHING CONNECTION literature accompanying the appliance CAUTION Please read and retain these safety instructions Heed all warnings in the operating instructions and on the appliance Do not use this appliance near water or moisture Clean only with a dry cloth Install in a good quality 19 equipment rack eU Pe NM m Do not install near sources of heat such as radiators heat registers stoves or other apparatus that produce heat such as amplifiers A Refer all servicing to
5. ally have loose connections Terminal Block Connectors e Pin 1 Contact Closure e Pin 2 Applied Voltage Contact Closure e Pin 3 Common e Pin 4 12V LED Output e Pin 5 Cascade e Pin 6 Aux Relay Contact e Pin 7 Aux Relay Contact surgex com energy intelligence CE SURGEX Connection Diagrams Four Sequencers Cascaded Together Cont Clos App Volt Common LED Cascade Aux Relay Aux Relay Sequencer controlling RT product Cont Clos App Volt Common LED Cascade Aux Relay Aux Relay Cascade Aux Relay Aux Relay Cont Clos Cont Clos App Volt LED LED Aux Relay Aux Relay 2014 SurgeX Electronic Systems Protection Inc Cont Clos App Volt Common LED Cascade Aux Relay Aux Relay Cont Clos App Volt Common LED Cascade Aux Relay Aux Relay surgex com CE SURGEX energy intelligence Wiring Diagrams Cascade Cascaded RAT Me i Pe TTL eee ee 2014 SurgeX Electronic Systems Protection Inc surgex com energy intelligence CE SURGEX Wiring Diagrams Cascaded F w PENIN ae IE Liu Cascaded Master Controller AMX Craztron Eutrom entr Reay fart Relay In FA FOIE i 14 EE CIS ar i 2 EL EU E S EROR EXE DEAR i MIS cps Raye 2014 SurgeX Electronic Systems Protection Inc surgex com CE Sequence Control Input The sequencer can be c
6. ard 19 inch equipment rack and requires one unit 1 U of rack space Use four rack screws to secure the rack ears to the rack rails Connect power to the unit by plugging the cord into a suitable 230V earthed AC receptacle The polarity light on the rear panel will illuminate if live and neutral are incorrectly connected If the polarity light is illuminated reverse the power plug where appropriate or get an electrician to correct the wiring of the receptacle 230 Volt Connections The sequencer has a total of 10 receptacles four sequenced banks of two and two always on Consult the table below for the load capabilities of each model Plug the equipment into the receptacle banks as needed to turn on equipment in the required sequence The Always On receptacles provide power as long as AC is supplied to the SEQ1200i The SEQ1200i runs sequentially during power up and down Bank A always powers up first and off last Bank D always powers up last and off first Model Maximum Load Per Outlet Total Maximum Load SEQ1210i 10 10 SEQ1213i 10 13 SEQ1215i 10 15 SEQ1216i 10 16 Remote Control Connections Remote connections are wired to the green 7 pin plug in terminal block on the rear of the unit next to the power cord After you have made the connections to the terminal block plug it into the connector on the rear of the unit Never solder tin wires before inserting ina terminal block the solder will cold flow and you will eventu
7. en Year Product Warranty AS3112 BS1363 BS546 and CEE 7 7 International Products Made in China For a period of 10 years from the date of your purchase of any SurgeX international product SurgeX warrants the product AS3112 BS1363 BS546 CEET7 7 standard against defects in materials used by SurgeX or workmanship performed by SurgeX a Covered Product SurgeX s obligations with respect to a Covered Product are to provide at no charge all labor and parts either new or rebuilt as determined in SurgeX s sole discretion necessary for the repair of the Covered Product If SurgeX in its sole discretion determines that a Covered Product is not repairable SurgeX will replace the Covered Product with a product of like kind quality and functionality In order to obtain the services under this Limited Warranty you are responsible for delivering the Covered Product at your sole cost to a SurgeX authorized distributor and for providing the SurgeX authorized distributor with a copy of the dealer s dated bill of sale as evidence of the date of purchase of the product THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY MADE BY SURGEX WITH RESPECT TO THE PRODUCT ALL IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR IMPLIED WARRANTIES ARISING OUT OF COURSE OF DEALING OR USAGE OF TRADE ARE HEREBY EXPRESSLY DISCLAIMED AND EXCLUDED
8. hever provides the best interface for the application However if one of these outputs is used for another function you will have to use the one that is available To use the 12V LED output for confirmation connect the 12V LED Output pin to the positive input of the controller and the Common pin to equipment earth The output will be at 12V when the unit is powered up and will be at zero volts when all banks are powered down Note that the common terminal is shared between the inputs and the 12V LED output and that the 12V LED output is limited to 10mA Operation The sequencer can be used in one of three configurations as a stand alone four bank sequencer with another remote controllable SurgeX product as a combination five bank sequencer or connected with other sequencers as a cascaded system of two or more units First make all basic connections as explained above Then if the system includes more than one unit make the additional 2014 SurgeX Electronic Systems Protection Inc SURGEX energy intelligence control connections between units as per the application diagrams Finally select the delay time by inserting a small screwdriver in the hole in the front panel The available delay times are 2s 5s 10s 15s and 20s The delay time must be selected on every unit when multiple units are cascaded together When all banks are off the bank status LED s are red If the sequencer is to be powered up only by using
9. l be powered up whenever the mains voltage is within normal limits the sequenced receptacles will only be activated if the power switch is on and a signal is also being received at the remote control terminal block on the rear panel Status LED s on the front panel show the status of each bank Red is off and green is on Flashing yellow LED s between the bank LED s indicate the unit is running a power up or power down sequence Multiple units can be cascaded to provide a scalable power control platform A single sequencer can also control multiple SurgeX remote control products Such as the RT or RTi to provide additional banks and also add more load capacity This is achieved by wiring units together using the remote control terminal blocks on the rear panel Remote control can be accomplished by using either a contact closure or a DC voltage from 5V to 30V Terminals are also provided for an external status LED Features e SurgeX Advanced Series Mode Surge Elimination e SurgeX Impedance Tolerant amp EMI RFI Filtering e SurgeX COUVS Over Under Voltage Shutdown 2014 SurgeX Electronic Systems Protection Inc e Accurate Front Panel Adjustable Time Delay e DC Voltage And Contact Closure Remote Control Inputs e Two Or More Units Can Be Cascaded e Auxiliary Relay Output For Control Of Other SurgeX Products e 12 Volt DC Output For External Status LED Installation The SurgeX SEQ1200i is designed to be installed in a stand
10. ontrolled by either a contact closure or a DC voltage from 5V to 30V A contact closure can be a relay contact or a latching switch A latching switch is one that stays in either the on or the off position like a light switch To use a relay contact or latching switch connect the contacts to pins 1 amp 2 To use a DC voltage connect the negative wire to pin 3 and the positive wire to pin 2 If the unit is going to be operated only by the front panel switch without a remote control input then place a short jumper wire between pins 1 amp 2 Switches with gold contacts are recommended for the best long term reliability External LED Connections The 12V LED output pin 4 is able to power an external LED and will provide 10mA of current An external LED connected to this output will indicate when the sequencer is powered up It is not necessary to use a series resistor unless the LED is too bright If this is the case you can try a 1K resistor or a 2 2K resistor in series with one of the LED leads Connect the LED anode to the 12V LED Output and the cathode to Common Confirmation Feedback The sequencer offers two ways to provide confirmation feedback to a central controller isolated relay contacts or the 12V LED output Confirmation tells the controller that the unit has indeed powered up or that it is fully powered down If the auxiliary relay contacts and 12V LED output are not used for any other function you will be free to choose whic
11. rst then banks D C B amp A As each bank switches off the bank status LED s change from green to red The flashing yellow LED s indicate the SEQ1200i is waiting for the delay time to elapse before moving to the next bank When multiple units are cascaded together the last unit in the chain powers down first Other Status LED s Red Power LED Shows that the mains is connected and the power switch is on Green Self Test LED Illuminates to indicate that the surge elimination circuitry is fully operational Orange Over Under Voltage Shutdown LED Illuminates if the mains voltage rises above 280 volts or falls below 180 volts When this LED is illuminated all receptacles are turned off surgex com CE Characteristics Protection type Nominal line to neutral voltage UO V SurgeX Advanced Series Mode 230V Max Cont Operating Voltage Uc V 260VAC Voltage protective level Up V 1KV Max shorted current Isc 3KA Open circuit voltage Uoc 6KV TOV characteristic UT TOV withstand tr 5s Ur 335V Degree of protection IP IP20 Disconnection Device Plug Applicable Power Supply System TN TT IT Polarity indicator near the supply cord Illuminated Incorrect Off correct Location Indoor Number of ports Two SURGEX energy intelligence Voltage regulation lt 196 Operation temperature and humidity 40 35 C 30 90 Importer XXXX Address XXXX SURGEX Limited T
12. the front panel power switch then bridge pins 1 amp 2 on the remote control connector with a jumper If a remote control input is to be used to power up the sequencer then leave the power switch on The power switch must be on to initiate the power up sequence whether a remote control input is used or not If the power switch is not being used it can be turned on and then covered using the supplied switch cover When multiple units are cascaded all the slave units should have their power switches turned on and covered When the power switch is on and the remote control input is activated the unit will begin the power up sequence The remote control input is activated by either a contact closing pins 1 amp 2 or a voltage of 5 30V being applied pins 2 amp 3 Bank A will always turn on first then banks B C amp D As each bank switches on the front panel bank status LED s change from red to green The flashing yellow LED s indicate the power up sequence is running Finally after bank D is powered up the auxiliary relay activates after the set delay time The auxiliary relay contacts are connected to the remote control connector pins 6 amp 7 and can be used to control another unit or provide feedback to a central controller When either the power switch is turned off or the remote control input is deactivated the unit will begin the power down sequence this is the reverse of the power up sequence The auxiliary relay will turn off fi
Download Pdf Manuals
Related Search