LEDBEAM 120F SI-029 User Manual
Contents
1. DMX512 master slave and sound activated controllable or auto operation High definition blue TFT LCD display Quiet smooth and fast PAN TILT movement Low noise and efficient FAN cooling system 540 PAN and 270 TILT movement Scan position memory auto reposition after unexpected movement Compact size with only 4 9KG body and 310mm in height IEC power connector 45 C max ambient temperature IP20 protection rating 3 Pin XLR DMX input output 4 Mounting and Installation Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture from a periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The LEDBEAM 120F provides a unique mounting bracket assembly that integrates the bottom of the base the2. sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions The moving head is for beam and wash effect for on site decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overhe
3. the chain Please see illustrations below 15 Reset 245 255 Rest after 3 seconds 120 PIN 3 PIN 2 E 6 Menu Operatio DMX Address Set 001200 EE Deeam m ns TILT 000 255 GREEN 000 255 BLUE 000 255 TestMode WHITE 000 255
4. the female 3 pin XLR output of your controller and the other side to Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below 3 TILT 0 255 Tilt Movement DMX 512 connection with DMX terminator 0 255 0 10096 Dimmer from dark to bright 6 Strobe 0 255 Strobe effect from slow to fast DEDERIT 0 255 0 10096 Red dimmer from dark to bright Green 0 255 0 10096 Green dimmer from dark to bright 0 255 0 10096 Blue dimmer from dark to bright White 0 255 0 10096 White dimmer from dark to bright 11 0 255 Color changing effect CONTROLLER Changing 0 010 CH1 CH11 valid DMX Output DMX I t 3 Pin XLR Socket 3 Pin XLR Socket COMMON 011 120 Color jumping e en DMX512 OUT DE DMX512 IN 12 Macro 121 180 Color fading 3 Data 4 3 PIN XLR Joo 3 PIN XLR 181 244 Mix color changing effect ar una conto For installations where the DMX cable has to run a long distance or is in an electrically noisy Macro environment such as in a discotheque it is recommended to use a DMX terminator This helps in 13 0 255 Speed of Macro effect from fast to slow Speed preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an Speed of PAN TILT XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output 0 244 CH1 CH14 valid XLR socket of the last fixture in
5. MC E 10W 4 IN 1 LEDs R G B W Control Signal DMX512 master slave and sound activated or auto operation Control Channel 15 DMX channels Power Consumption 140W Dimensions 152 D 265 W 310 H mm Packing Dimensions 260 D 320 W 335 H mm Net Weight 4 9kg Gross Weight 7kg 2 Safety Instructions CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by
6. ach other for operation And it is applicable for large scale live performances theater studio nightclubs and discos CAUTION Disconnect from mains before starting maintenance operation SI 029 adopts 12PCS CREE XLamp MC E 10W 4 IN 1 LEDs RGBW which features high In order to make the lights in good condition and extend the life time we suggest a regular cleaning to brightness and stability Please carefully unpack it when you receive the fixture and check whether the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due itis damaged during the transportation And please check whether the following items are included to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved inside the box electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating LEDBEAM 120 One Signal Cable One We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use Hanging Bracket One Power Cable One alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions Safety Chain One User Manual One under Installation instructions Should you need any spare parts please order genuine parts from your local dealer 10 Specifications Input Voltage AC90 260V 50 60Hz LED Quantities 12PCS CREE XLamp
7. at moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 9 Key Features 12PCS CREE XLamp MC E 10W 4 IN 1 LEDs R G B W 60 000 hours life span for LEDs and low power consumption Intelligent temperature sensor for LEDs over heat protection High efficiency 8 degree optic lens Color range with 16 7 millions additive RGBW colors High light output as 684LUX 7M at full 0 100 smooth linear dimmer with flicker free 20t s strobe effect with variable speed Pre programmed random strobe and pulse effects 15CH DMX channels Built in programs with macro effects
8. included Omega Bracket and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly 8 Photometric Data llb Photometric Beam Angle Data amp Beam Angle LUX x 0 0929 FC n R 348 3750 45 480 17 180 9 90 G 466 5020 61 660 23 285 13 140 obice B 1098 11820 125 1350 44 470 22 240 Ww 1004 10810 122 1310 43 460 21 283 RGBW 2731 29400 _ 7333 3580 116 1250 60 684 FC LUX Turn around Turn around 4 Regardless of the rigging option you choose for your LEDBEAM 120F always be sure to secure your fixture with safety cable The fixture provides a built in rigging point for safety cable on the hanging Om Oft 1m 3 3ft 3m 9 8ft 5m 16 4ft 7m 23 0ft bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 7 DMX Channels 5 DMX 512 control connections _ Function Values Description Connect the provided XLR cable to
9. ol ur ON CE LEDBEAM 120F 51 029 User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking 11 Maintenance and Cleaning Thank you for choosing Color Imagination s LEDBEAM 120F For your own safety please read The following points have to be considered during the inspection this manual before installing the device This manual covers the important information on 1 All screws for installing the devices or parts of the device have to be tightly connected and must not installation and applications Please install and operate the fixture with following instructions be corroded 2 There must not be any deformations on the housing color lenses fixations and Meanwhile please keep this manual well for future needs installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not Color Imagination s LEDBEAM 120F is made of a new type of high temperature strength of show any damage material fatigue or sediments engineering plastics and cast aluminum casing with nice outlook The fixture is designed and Further instructions depending on the installation spot and usage have to be adhered by a skilled manufactured strictly following CE standards complying with international standard DMX512 installer and any safety problems have to be removed protocol It s available independently controlled and linkable with e
Download Pdf Manuals
Related Search