Ax51B IR Bullet Camera User Guide
Contents
1. Auto Exposure Select this option to correct the exposure automatically Method Select either Center Weighted or Object Targeted If Object Targeted method is selected select the target areas by clicking squares displayed on the Exposure Mode preview screen EV Set exposure value between 2 and 2 Higher values produce brighter Images Max Exposure Set the maximum exposure time Values range from 1 3 5 to 1 1000 Min Exposure Set the minimum exposure time Values range from 1 30 to Unlimited sensitivity Set the exposure sensitivity Exposure will increase as the sensitivity value increases relative to the time interval Values range from 1 to 10 with 10 being the most sensitive 26 I3 TRNG CAMS Ax51B indd Rev 130411 e Max Gain Set the maximum gain value The higher value will enhance the video signal Note that the noise will also be enhanced Values range from 2 to 16 to Default Manual Exposure Select this option to correct the exposure manually e Exposure Time Set the exposure time Acceptable value range is from 1 10000 to 1 3 5 sec e Gain Set the Gain value The values range from U to 16 BLC Configuration e When parts of the environment are poorly lit BLC can be turned ON to compensate for inadequate lighting conditions To configure the individual areas that will receive compensation click on the squares displayed in the BLC Configuration preview screen Enabled areas will be shaded purple Digital WDR2. 3 l Ax51B IR Bullet Camera Pinternationat User Guide 4 w i d CONTENTS 1 Warnings and operation notes 3 2 Product Overview eere 4 MEMINI OI ee EE D 4 Installation eeeeeeeeeene 6 5 Connecting your IP Camera to the SRX Pro Server 1 6 Advanced Camera Setup 15 7 SpPECCAONS eio n Ia EREE 20 Before attempting to connect or operate this product read these instructions carefully Save this manual for future use Ax51B IR Bullet Camera User Guide COPYRIGHT 2013 by i3 International Inc All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including but not limited to photocopying recording or by any information storage or retrieval system without the prior written permission of the copyright owner and the publisher Annexxus is a registered trademark of i3 International Inc Disclaimer This user guide is provided as is without warranty of any kind expressed or implied including but not limited to performance merchantability or fitness for any particular purpose Neither i3 International Inc nor its dealers or distributors shall be liable to any person or entity with respect to any liability loss or damage caused or alleged to have been caused dir
3. e Set the Wide Dynamic Range Level if desired The WDR can be turned OFF set to Auto or to Levels 1 5 i3 TRNG CAMS Ax51B indd a Rev 130411 7 Specifications Features Model AxMB Image System o U 1 2 2 MP image sensor optimized for low light performance Triple Streaming H 264 MPEG4 Motion JPEG Maximum Framerate vs Up to 15fps NTSCI 12 5fps PAL at 1920x1080 2M Resolution Built in fixed lens f 3 1mm F 2 0 2 Megapixel lens 71 x 595 H 57 x 5 V Shutter Time Range from 1 10000s to 1 3 75s selectable 60Hz Range from 1 10000s to 1 3125s selectable 50Hz IR LED OFF 1 5 lux F2 0 50 IRE 1 15s IR LED ON 0 lux More than 10 000 hours 50 C Exposure Mode Auto Manual White Balance Auto Manual Image Enhance Backlight Compensation 5x5 zones selectable Sharpness Saturation Brightness Contrast 255 level sensitivit Privacy Zone Yes customized threshold privacy zone Motion Detection 5 x 5 Motion detection zones amp 5 level Alarm Detection an sensitivity or customized threshold Image Orientation Mirror Flip System Log Time Stamp Snapshot User Management Power Requirement outdoor DC 24V 1095 AC 24V 10 Power Requirement indoor PoE Class 3 IEEE802 3af DC 12V 10 AC 24V 10 lt BW Heater OFF IR LED ON Network SS SS ee O Ethernet 10Base T 100Base TX Ethernet connection fo
4. the power consumption requirements of this camera before powering the camera on Incorrect voltage may cause irreparable damage to the video camera and will effectively void the camera warranty PoE DC12V and AC24V power is supported in the indoor installations where the heater is not required Use DC24V AC24V power for outdoor installations only to supply enough power to the built in heater 1 3 Cleaning e For maximum optical clarity the camera or lens must remain clean Use a soft dry cloth to remove finger prints and dust from the dome cover e Use a blower to remove dust from the lens e lean the body with a soft dry cloth If it is very dirty use a cloth dampened with a small quantity of neutral detergent then wipe dry e o not use volatile solvents such as alcohol benzene or thinners as they may damage the surface finish 1 4 Servicing To avoid electrical shock and to preserve the product warranty DO NOT disassembles the camera Refer servicing to qualified personnel only 2 Product Overview e High Definition Images Clear and detailed HD quality images in all conditions Unlike other megapixel cameras Ax51B series offer higher resolutions and better frame rates Blurry images are reduced and individuals and objects of interest come with perfect clarity i3 TRNG CAMS Ax51B indd Rev 130411 e Triple Streaming The Ax51B series Network Camera is designed to show extreme image detail H 264 MPEG4 MJPEG triple stream
5. 60 x 240 2CIF 720 x 240 VGA 640 x 480 D1 720x480 e Dit Rate Set the video bit rate from 500 4000 kbit s e Frame Rate Set the frame rate for the recorded video to 1 3 7 5 15 fps or 30 fps Configure Stream 3 Third Streaming Live View e Video Codec OFF or MJPEG OFF setting will result in no video on Live View e Resolution Resolution for Third Streaming is pre set to VGA and cannot be changed i3 TRNG CAMS Ax51B indd Rev 130411 Advance Settings e White Balance Set White Balance mode to Auto or Manual according to the images lighting conditions for the best color temperature e Sensitivity Use when White Balance is set to Auto Set between 1 and 10 Adjust the sensitivity of the camera s white balance function manually e R Gain G Gain B Gain Use when White Balance is set to Manual Adjust levels of red green and blue in the image Values can be set from 0 4 4 0 e Brightness adjust the image brightness level Values range from 0 to 100 e Contrast adjust the image contrast level Values range from 0 to 100 e Saturation adjust the image saturation level Values range from 0 to 100 e Sharpness adjust the image sharpness level Values range from 0 to 100 After making any setting adjustments remember to click the Save button J to save any changes made 6 3 Communication Setup Disabled mi us pool ntp org 18 f8 7a 00 c3 cb The Communication tab is used to configure ne
6. You can download the updates from ftp files 123ip com drivers gipi Please contact i3 Technical Support team for access information 2 Once the latest GiPi updater has been installed restart i3 SRX Pro Server software Log In and go to the Setup gt IP Camera tab 4 Click the Search button to display connected Annexxus cameras select the detected camera in the list and click Select I3 TRNG CAMS Ax51B indd Rev 130411 6 Inthe Select IP Camera window enter the default camera User Name admin Hardware Motion User Management Schedule Server Info Video System Storage E Map Log Records Intelli Guard Communication Text Overlay IntellizZone VideoLogis VisionCount VideoPrivacy LPR IP Camera Recording Display Virtual Ruler E Mail Selected Camera Info Note To add new IP Cameras click the Add button or click the Search button to search the network for existing IP Cameras Add d Edt X Delet Camera P Add Input Resolution User i3dw Location ServerID 100 001 03 10 2012 01 53 45 PM and default Password 7234 then click Add Search For IP Camera Select Model LL MODELS mp 0 2 In Use Model mac IPAddess Pot Mask Gateway ANNEXUS 5x 132 0 0 16 ANNEXXUS 5x 192 0 0 15 This model can t be searched on the network should add manually i3 TRNG CAMS Ax51B indd n Rev 130411 7 The selected camera will be added to
7. ection you can configure basic camera system settings e ime Stamp Select Yes to enable Date and Time Stamp to display the date and time on the camera feed Select No to hide it e Current Date amp Time Displays the camera s current date and time e New Date amp Time You may choose to Set the Date and Time Manually Synchronize Date amp Time with Computer Time or Synchronize Date amp Time with NTP Server NTP Server and Time Zone can be configured in the Communication Setup tab See section 6 3 for details e Date formats include YYYY MM DD MM DD YYYY and DD MM YYYY System Information his section contains information on the Camera s Kernel BIOS version and App firmware version Update All Annexxus series cameras are sold with the most recent version of the firmware already installed f in the future firmware updates are released you can update your camera s firmware by first downloading the firmware file from i3 International s website or FTP site After downloading firmware file click the Browse button in the camera s System setup tab and locate the new firmware file Then click the Update button and wait while the firmware is being updated on your camera Note Be sure to stop all camera operations prior to an update Do not turn off power or disconnect from the network during the process Click Restart Camera after you have updated firmware successfully Restart Reset e Click Restart Camera to restar
8. ectly or indirectly by this information Furthermore i3 International Inc reserves the right to revise this publication and to make changes to the content at any time without notice FCC This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Address Contact us i3 International Inc Tech Support 1 877 877 1241 780 Birchmount Road Unit 16 Email support i3international com Scarborough ON M1K 5H4 Web Site www i3international com Canada Table of Contents Warnings and operation notes Product Overview Unpacking Installation Configuration Advanced Camera Setup Specifications TRNG CAMS Ax51B indd Rev 130411 Cc 1 Warnings and operation notes Thank you for purchasing i3 Ax51B IR Fixed Bullet camera Please read this guide carefully before you install the camera Keep this guide for future reference Ax51B comes with a fixed lens and a built in heater 24 high quality IR illuminators built around the lens facilitate crystal clear pictures with no outside illumination as far as 25 meters 82 ft Plus with P67 rated all weather waterproof aluminum casing this camera is ideal for outdoor applications such as convenience stores streets and parking lots PoE DC12V and AC24V power is supported in t
9. er List 6 6 Logs Logs setup tab displays all login and Alarms log records System Log 000 2000 01 21 13 37 10 admin login on 192 0 0 138 001 2000 01 21 13 12 47 admin login on 192 0 0 138 002 2000 01 01 13 11 50 admin login on 192 0 0 138 I3 TRNG CAMS Ax51B indd Rev 130411 6 7 Privacy Zone optional In the Privacy Zone setup tab select an area that needs to be blocked off with a black rectangle on Live View and from video recording because of privacy or other Concerns To draw the privacy zone follow these instructions 1 Position your mouse cursor over the Preview window press and hold the left mouse button 2 While holding down the left mouse button drag the cursor to draw a rectangular area over the zone that needs to be concealed 3 Release the mouse button The privacy area rectangle will be shaded purple in the Preview window 4 f you are not satisfied with the size or positioning of the privacy zone repeat steps 1 3 to re draw it 5 Set the Privacy Zone to ON to activate this setting After making any setting adjustments remember to click the Save button to save any changes made i3 TRNG CAMS Ax51B indd Ey Rev 130411 6 8 Exposure set the exposure level for your camera Exposure time determines how much light passes through the camera aperture to the focus Center Weighted jf io Jui evs UNLIMITED 10 Er i 5n Yvl DEFAULT E 30 00 O n A
10. ersion 3 0 or higher e Latest GiPi adapter is installed GiPi adapters can be downloaded from i3 FIP website Please contact 13 Technical Support for more information e Windows XP XPe or Pro or e e Internet Explorer Version 6 0 or later e CPU Intel Pentium Core 2 or higher e Memory 1GB or more e VGA card supporting Direct X 9 0 or above Power Supply PoE DC12V and AC24V power is supported in the indoor installations where the heater is not required Use DC24V AC24V power for outdoor installations only to supply enough power to the built in heater Note Camera damages resulted from improper power application are NOT covered by the camera warranty Switch A Gigabit Switch is required to monitor two or more cameras from the same SRX Pro Server 5 3 Using Annexxus Finder to assign IP Address to your IP Camera To connect your Annexxus camera to your SRX Pro Server follow these instructions i3 TRNG CAMS Ax51B indd Rev 130411 Close SRX Pro Server software by pressing Alt Shift Ctrl FA Change the IP address on the onboard NIC LAN or on NICT if your SRX Pro server has two onboard NIC cards of your SRX Pro Server to 192 0 0 XXX to Camera s default IP address is 192 0 0 16 Camera s default subnet mask address is 255 255 255 0 Default camera User Name admin and default Password 7234 match the default IP range of your Annexxus IP camera Connect the network cable from the SRX Pro Server cross
11. features 6 1 Basic Setup After making any setting adjustments remember to click the Save button to save any changes made You may switch to the advanced setup at any time by clicking the button in the bottom left hand corner To switch back to the Basic Setup click the same button again I3 TRNG CAMS Ax51B indd Rev 130411 Basic Setup is divided into Camera and Network settings Settings that can be configured in this setup tab Camera Settings e Camera Name The name of the camera will be displayed at the top of the Internet browser page e Video Codec Set the compression mode to MJPEG H264 or MPEG4 e Resolution Set the resolution of the recorded video to D1 SVGA XGA 720P SXVGA or 1080P full HD e Bit Rate for H264 MPEG4 codecs Set the video bit rate from 500 8000 kbit s e Quality for MJPEG codec only HIGH NORMAL LOW e Fame Rate Set the frame rate for the recorded video to 1 3 7 5 10 15 available only with 1080P resolution or 30 fps unavailable with 1080P resolution Network settings e DHCP Enable or Disable to have the network automatically assign an IP address to the camera e P Address Manually enter the camera s IP address here This option should NOT be used if DHCP is enabled e eubnet Mask Manually enter the camera s Subnet Mask here This option should NOT be used if DHCP is enabled e Default Gateway Provide the IP address of the network s router if necessary Contact yo
12. he camera s setup settings while Viewer may only view camera live stream Up to 10 unique users can be created per Annexxus camera Note he default Administrator account admin 1234 may not be deleted 6 5 1 Changing the Password on the Default Account Note You may use these instructions to change password for any existing user account To do so follow instructions below but enter the desired account name in step 1 instead of typing admin To change the password on the default admin account follow instructions below 1 Type admin in the Username field of the Add Modity User area 2 Enter new password in the Password field of the Add Modity User area i3 TRNG CAMS Ax51B indd Rev 130411 3 Ensure Permission is set to Administrator 4 Click the Add User button 5 The message will be displayed User information has been changed The default password for the admin user has now been changed 6 5 2 Adding New User To add a new user follow instructions below 1 Enter new user name in the Username field of the Add Modify User area 2 Enter password in the Password field of the Add Modify User area 3 Set Permission to Viewer or Administrator 4 Click the Add User button New user will be added to the User List 6 5 3 Deleting User To delete a user follow instructions below 1 Select a user in the User List 2 Click the Delete User button 3 Click OK in a confirmation window The user will be deleted from Us
13. he indoor installations where the heater is not required Use DC24V AC24V power for outdoor installations only to supply enough power to the built in heater If the system needs to be modified or repaired contact a certified i3 International Dealer Installer When serviced by an unauthorized technician the system warranty will be voided Should you have any problems or questions regarding our products contact your local i3 International Dealer Installer 1 1 Precautions Installation and serving should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty When installing your Ax51B camera be sure to avoid excessive heat such as direct sunlight or heating appliances e contaminants such as dust and smoke e strong magnetic fields e sources of powerful electromagnetic radiation such as radios or TV transmitters e moisture and humidity areas with mechanical vibrations e fluorescent lamps or objects that reflect light e unstable light sources as this may cause flickering e temperatures below 40 Celsius or 40 Fahrenheit and above 50 Celsius or 122 Fahrenheit i3 TRNG CAMS Ax51B indd Rev 130411 WARNING The use of CSA certified UL Listed Class 2 power adapter is required to ensure compliance WARNING To reduce the risk of fire or electric shock do not expose the product to rain or moisture 1 2 Power Supply Ensure the supplied voltage meets
14. ing allows you to choose the appropriate code for your bandwidth e Cost saving H 264 Support The AX51B series support the H 264 compression standard H 264 greatly reduces the size of video without compromising image quality Storage and bandwidth are reduced 3 Unpacking Ensure that the items received match those listed on the order form and packing slip The dome camera packing box includes in addition to this manual Flat Head Screw Tapping Type x3 Plastic Anchor x3 RJ 45 Female Female Coupler Mounting Pack in Bracket Guide Pattern Sticker x1 Printed Quick Start Guide x1 CD User Manual Annexxus Finder Quick Start Guide x1 Fully Assembled Network Bullet IR Camera x1 Guide Pattern O O Note Mounting surface material determines screw type Ce e es liii d If any parts are missing or damaged contact the dealer you purchased the camera from i3 TRNG CAMS Ax51B indd Rev 130411 4 Installation Use the provided bracket and equipment to mount the camera After installation your network camera should be accessed from your local network See Section 5 Connecting your IP Camera to SRX Pro Server 4 1 Dimensions 162mm 6 4 T Power In x ied BI adc e E RJ 45 Ethernet E Connector oO C BNC 111mm 4 4 CO 5 gt g 0mm 2 76 A Power In Red Black power connector Use DC12V AC24V for indoor applications use DC24V AC24V for outdoor ap plica
15. lowing message to be displayed Click OK to close it Repeat Steps 1 12 for all detected Annexxus cameras in the Annexxus Finder Now that the new IP address has been successfully assigned to your camera make sure you can connect to it through the Internet Explorer Launch Internet Explorer on your SRX Pro Server and enter the IP Address you have just assigned to your Annexxus camera The password window should be displayed Annexaus Finder The server 192 0 0 16 at IPMC requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name If admin Password IIT Remember my password ca 11 i3 TRNG CAMS Ax51B indd Enter the default camera User Name admin and default Password 7234 Annexxus camera Interface will be displayed in the Internet Explorer window You should be able to see the camera image on the screen Rev 130411 If you do not see the camera image on the screen call i3 International tech support for troubleshooting tips 1 877 877 1241 5 4 Adding your IP Camera to your SRX Pro Server http 192 0 0 15 livex html Microsoft Internet Explorer 7 provided by i3 International http www i3international com Oo EE ANN SUSE ENN sy gt lt M TELCO aW ts E 1 Make sure that the latest version of GiPi updater is installed on your SRX Pro server
16. over direct connection or from the Gigabit switch to your Annexxus camera Turn on your Annexxus camera Locate the CD that came with your Annexxus camera and insert it in the CD ROM drive of your SRX Pro Server Double click AnnexxusFinder exe file to install Annexxus Finder application Annexxus Finder application discovers all Annexxus cameras connected to your network Follow the Annexxus Finder installation instructions until the application has been successfully installed on your SRX Pro Server Double click Annexxus Finder icon on the Desktop to launch the application The application window will appear displaying a list of active network cameras Next select desired camera in the Annexxus Finder software by double clicking it in the list and click Edit Enter the new IP address and Subnet Mask of the camera in the Change IP I3 TRNG CAMS Ax51B indd Rev 130411 Address area The new camera IP address must match the original range of your SRX Pro LAN or NIC1 card E g If your original SRX Pro Server s IP address was 192 138 10 122 change your Annexxus camera s IP address to 192 138 10 XXX Remember Annexxus Cameras cannot share an IP address each camera requires its own unique IP address 11 Enter the default camera password 1234 in the Input Password field and click i3 TRNG CAMS Ax51B indd Rev 130411 Save Wait a few moments as the new IP address is being applied to your Annexxus camera Wait for the fol
17. r LAN WAN RJ 45 IPv4 TCP IP UDP HTTP HTTPs SMTP DNS DHCP NTP FTP RTP RTSP ICMP uPnP SRX Pro Server SRX Pro Remote Agent OR IE Browser 6 0 or above Internet Protocol Browser 1 0 Connector lt b sec for rebooting the camera Reset gt 5 sec for loading default settings Mechanism O Dimensions 0xH 070mm x 162mm x 81 5mm 2 76 x 6 38 x 3 21 550g 1 116 The specifications are subjects to be change without notice I3 TRNG CAMS Ax51B indd i Rev 130411 eatures Model cont erating Temperature 40 C 50 C 40 F 122 F perating Humidit 10 90 RH torage Temperature 20 C 60 C 4 F 140 F rotection Class IP67 egulator CE FCC RoHS Wall mount Ceiling mount with free pack in bracket Storage Temperatue 20 C OC APF 140 Protection Class PPB Regulatory CEFCC RoHS i3 TRNG CAMS Ax51B indd i Rev 130411 i3 INTERNATIONAL INC 3 n I INTERNATIONAL 1 866 840 0004 U S A 1967 Wehrle Drive Canada 780 Birchmount Road www i3international com Suite 1 PMBZ 034 Buffalo Unit 16 Scarborough NY 14221 ON M1K 5H4
18. sed on video analytics where quality is desired CBR Constant Bit Rate Produces the smoothest streaming for variable scenes but is not ideal if highest image quality is desired i3 TRNG CAMS Ax51B indd ie Rev 130411 Annexxus 51B camera series supports triple streaming where Primary Streaming Is the default stream used for video recording and Third Streaming is used for Live Viewing Each stream can be configured separately Note Enabling Streams 2 and 3 may cause frames being dropped on Stream 1 Configure Stream 1 Primary Streaming Recorded Video e Video Codec Set the compression mode to MJPEG H264 or MPEG4 e Resolution Set the resolution of the recorded video to one of the following D1 720x480 SVGA 800 x 600 XGA 1024 x 768 120P 1280 x 720 SXVGA 1280 x 960 or 1080P 1920 x 1080 full HD Note that when the Resolution on the Primary Streaming is set to 1080P secondary streaming will be disabled e Bit Rate for H264 MPEG4 codecs Set the video bit rate trom 500 8000 kbit s e Quality for MJPEG codec only HIGH NORMAL LOW e Frame Rate Set the frame rate for the recorded video to 1 3 7 5 10 15 available only with 1080P resolution or 30 fps unavailable with 1080P resolution Configure Stream 2 Secondary Streaming e Video Codec Set the compression mode to OFF disable secondary streaming H264 or MPEGA e Resolution Set the resolution of the recorded video to CIF 3
19. t your Annexxus series camera This will cause a temporary disconnect no video will be recorded while the camera Is restarting but all custom settings will be saved Camera restart is required after the firmware update After clicking a pop up will appear asking you to confirm Click Yes e lick Factory Reset to return all settings except for the Networking IP settings to factory defaults After clicking a pop up will appear asking you to confirm Click Yes e lick Hard Factory Reset to return all camera settings including IP address to factory defaults After clicking a pop up will appear asking you to confirm i3 TRNG CAMS Ax51B indd Rev 130411 Click Yes Note Your Network Camera s default IP address is 192 0 0 16 and the default subnet mask address is 255 255 255 0 After making any setting adjustments remember to click the Save button LJ to save any changes made 6 5 User Management User Management tab displays the list of users that have access to the Annexxus camera The username and password from this setup tab are used when connecting the camera to SRX Pro Server See section 5 page 16 for more information Reminder Whenever a change is made to the Annexxus camera user in the camera s Advanced Setup gt User Management tab remember to update this information in the P Setup tab of the SRX Pro Server Two types of user permissions exist Aministrator and Viewer Administrator users have access to t
20. the IP Camera list Don t forget to assign the IP camera to the SRX Pro video channel in the Select IP Camera corresponding column highlighted 8 Your Annexxus camera is now connected to SRX Pro Server and is ready to record You may change resolution and frame rate for the Annexxus camera in El All Cameras D MEAE 192 0 0 15 80 192 0 0 16 80 EA Ee M E E the P Camera tab menu or you may choose to configure the camera s advanced settings see the following section i3 TRNG CAMS Ax51B indd Rev 130411 6 Advanced Camera Setup To access Annexxus camera s advanced setup go to Setup gt IP Camera tab select the camera in the list of added IP cameras and click the Advanced Setup button E All Cameras 8n E2856 1 Channel m 1320x1080 2 Channel 2 The password window should be displayed Enter the default camera User Name admin and default Password 7234 Camera s user interface will be displayed in a separate Internet Explorer window ES e BE T tte E i3 TRNG CAMS Ax51B indd hn Rev 130411 Video Adjustments In the main interface you may adjust your camera s Brightness Contrast Saturation and Sharpness levels Click Save to save adjusted settings or Default to set all settings back to 50 Note his panel is enabled in the Live View mode only and is disabled when in the Setup mode Next click the Setup button to access Annexxus camera Setup
21. tions to supply enough power to the built in heater B RJ 45 Ethernet Connector network connection supports PoE Power over Ethernet cable for indoor applications PoE power will not work when the camera is installed outdoors where the use of heater is required for camera operations Note If PoE Power over Ethernet connector is used an electrical cable is not required C BNC video output i3 TRNG CAMS Ax51B indd Rev 130411 4 3 Wall Ceiling Mount Installation Adjusting Camera Position 1 Adhere the Guide Pattern Sticker to the desired location on the mounting surface and mark hole positions 2 Drill 3 mounting holes on the mounting surface according to the guide sticker 3 For cement surfaces insert the Plastic Anchors into the holes For softer sur faces do not use the Plastic anchors 4 Secure the mounting bracket to the surface using the provided screws Anchors Plastic Tapping Anchors Tapping To adjust the view Type angle loosen the knob Screws to rotate the bracket 5 Connecting your IP Camera to the SRX Pro Server 5 1 Camera Connection Options Connection Type 1 Crossover direct connection Connection Type 2 i3 SRX Pro Server Via Gigabit Switch I3 TRNG CAMS Ax51B indd Rev 130411 5 2 Hardware Software Requirements The following requirements must be met to achieve a successful network connection with the Ax51B IR Bullet IP camera SRX Pro Server e 3 SRX Pro V
22. twork and communication settings on the camera Network settings e DHCP Enable or Disable to have the network automatically assign an IP address to the camera e P Address Manually enter the camera s IP address here This option should NOT be used if DHCP is enabled e Subnet Mask Manually enter the camera s Subnet Mask here This option should NOT be used if DHCP is enabled i3 TRNG CAMS Ax51B indd 2 Rev 130411 e Default Gateway Provide the IP address of the network s router if necessary Contact your network administrator for this information e DNS Specify a DNS if necessary Contact your network administrator for this information e HTTP Port Use the default Port 80 if possible Contact your network administrator if the setting needs to be changed e Physical Address This is the camera s unique MAC Address It may not be changed NTP Server setting Enter NTP Server setting information to synchronize the camera with an NTP server e NIP Server assign an IP address or domain name for a time server Default NTP Server us pool ntp org e ime Zone select the correct time zone After making any setting adjustments remember to click the Save button to save any changes made 6 4 System Setup Current Date amp Time New Date amp Time 5 EI Fri Oct 5 16 37 20 EDT 2012 us pool ntp o GMT 05 Eastern Time MM DD YYYY i3 TRNG CAMS Ax51B indd Rev 130411 In this s
23. ur network administrator for this information e DNS Specify a DNS if necessary Contact your network administrator for this information e Physical Address This is the camera s unique MAC Address t may not be changed 6 2 Video Setup Switch to the Advanced Setup by clicking the Advance Setup button on the bottom left hand corner of the screen as shown on the previous page The Setup screen will change to reveal multiple setup tabs Video Setup tab is displayed by default I3 TRNG CAMS Ax51B indd Rev 130411 PY ee c Li I xd FN c REC ANNEXXUS43 Pe ee de ll LR S Camera Settings e Frequency Select the option which best reduces image flicker 50Hz or 60Hz e TV System NTSC or PAL Your camera comes pre programmed with this setting If you find that your camera came pre programmed with the wrong TV system setting contact the dealer you purchased the camera from e Mirror Hips the video image The options for mirror are OFF Do not use this feature HORIZONTAL flip images left to right VERTICAL flip images upside down BOTH flip both HORIZONTAL and VERTICAL e Rate Control Choose the bit rate of encoding The options for rate control are VBR Variable Bit Rate Maintains good image quality but will consume more bandwidth This setting is not recommended for variable scenes such as outdoor environments but is best suited for recording to a local storage drive or ba
Download Pdf Manuals
Related Search