1. - Vivitek
Contents
1. 1aVOUTA 12VOUTB vivitek Vivid Color Vivid Life DLP Projector User s Manual 9 Turn on your source that you want to display on the screen computer note book video player etc The projector will detect the source automatically and will display on the screen If not push menu button and go to SETUP gt gt Ba PRETI SIC 000 COMPONENT Note If you connected multiple sources at VIDEO the same time press the Source key on the remote control to switch S VIDEO between inputs e PC Analog RGB SCART e HDMI 1 2 3 High Definition Multimedia Interface e COMPONENT DVD input YCbCr YPbPr HDTV input YPbPr e VIDEO Traditional composite video e S VIDEO Super video Y C separated Note Turn on the projector first and then select the signal sources First time to turn on the projector Remember to select the type of lens you have installed Shutting down the Projector 1 Press the 222 button on the remote POWER OFF control J button on the rear POWER side of the projector two times with one Press button again to power second interval in between to turn off the projector First push of button will off display the following message on the screen Press the button again to confirm the Press any other button to cancel shut down If the button is n2. PICTURE gt gt Advanced Menu Press the MENU button to open the OSD menu Press the cursor lt button to move to the PICTURE gt gt Advanced menu Press the cursor A V button to move up and down in the PICTURE gt gt Advanced menu Press to change values for settings A PICTURE gt gt Advanced Noise Reduction 1 Color Temperature Lamp Native Gamma Color Gamut Native HSG Adjustment Color Space Auto DynamicBlack Cinema 1 IRIS ViviSettings ITEM DESCRIPTION Noise Reduction Press the cursor lt P button to adjust the Noise Reduction Color Temperature Press the cursor button to set the Color Temperature Gamma Press the cursor gt button to adjust the gamma correction of the display Notes This function is only available in User 1 2 3 mode Color Gamut Press the cursor gt button to set the Color Gamut Range Native Cinema HDTV EBU SMPTE C HSG Adiustment Press the ENTER button to enter the HSG Adjustment sub menu J See HSG Adjustment on page 26 Press the cursor lt P button to set the Color Space Color Space Range Auto RGB SDTV HDTV Notes This function is only available when HDMI input source is selected Press the cursor gt button to set the DynamicBlack DynamicBlack enables the projector to automatically optimize the display of dark movie DynamicBlack scenes enabling them to be shown in incredible detail to the overall brightness of darker scenes resu
3. confirm highlighted OSD menu item BLANK Displays a blank screen and mutes audio Iyem 44 Left cursor Navigates and changes settings in the OSD amp Optimizes image size position and resolution gt Right cursor Navigates and changes settings in the OSD Down cursor Navigates and changes settings in the OSD Keystone Quick Menu For Keystone DLP Projector User s Manual Rear view 17 16 15 1413 12 1110 98765 ITEM LABEL DESCRIPTION SEE PAGE MC 772 7777 L2 e _ meas ETE A IRreceiver receiver Receive IR signal from remote control Red Emoreode S LAMP LED Lamp is not ready warming up shutting Flashing down cooling see LED Error Messages on page 40 pwR LED Flashing Powering on cooling Turns the projector on or off main power switch must be POWER turned on first Press to place the projector in standby mode 40 RS 232C Connects RS 232 Connects RS 232 serial port cable for remote control Connects RS 232 serial port cable for remote control cable for remote control
4. HDMI 1 HDMI2 Press the lt P buttons to enable or disable the HDMI source HDMI 3 Component Press the lt P buttons to enable or disable the Component source Video Press the lt buttons to enable or disable the Video source S Video Press the lt P buttons to enable or disable the S Video source Press the lt 4 gt buttons to enable or disable Quick Auto Search for available input source Notes When the desired source is selected the Quick Auto Search function will be turn off 30 DLP Projector User s Manual SETUP gt gt Advanced Menu Press the MENU button to open the OSD menu Press the cursor lt button to move to the SETUP gt gt Advanced menu Press the cursor A V button to move up and down in the SETUP gt gt Advanced menu Gb SETUP gt gt Advanced Lamp ES HDMI High Altitude Mode i Closed Caption 5 LED Control Normal 12 OUT A On 12V OUT B On 9 Lens Type Standard Reset All ITEM DESCRIPTION Press the ENTER button to enter the Lamp sub menu See Lamp on page 32 HDMI Press the ENTER button to enter the HDMI sub menu See HDMI on page 32 Press the cursor lt P buttons to turn on or off High Altitude Mode when the altitude of the environment is higher than 1500m or the temperature is over 40 C Closed Caption Press the ENTER button to enter the Closed Caption sub menu P See Closed Caption on page 33 LED Control Press the cursor lt P buttons to se
5. When connected to the screen through a commercially avail 12V OUT A B able cable the screen deploys automatically on start up of the projector The screen retracts when the projector is pow ered off see notes below Note e To use this feature you must turn on the Screen Trigger function on the OSD e Screen controllers are supplied and supported by screen manufacturers Do not use this jack for anything other than intended use DLP Projector User s Manual ITEM LABEL DESCRIPTION SEE PAGE MN VGA SCART YPbPr Connects the RGB cable from a computer 12 E 43 S VIDEO Connects the S Video cable from a video device 406 Security chain lock Helps protect the H5080 from unauthorized use Secures to permanent object with a Kensington amp Lock DLP Projector User s Manual Bottom view gt lt 260 00 gt DESCRIPTION SEE PAGE Tilt adjustor Rotate adjuster lever to adjust angle position Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling Note When installing ensure that you use only UL Listed ceiling mounts For ceiling installations use approved mounting hardware and M4 screws with a maximum screw depth of 6 mm 0 23 inch The construction of t
6. investigates these instances to ensure that the HDMI trademark is properly used in the market We recommend that consumers buy their cables from a reputable source and a company that is trusted For more detail information check http www hdmi org learningcenter fag aspx 49 43 DLP Projector User s Manual Specifications Model Display Native Resolution Weight Lens type Projection distance Projection screen size Projection lens Zoom ratio Vertical keystone correction Projection methods Data compatibility SDTV EDTV HDTV Video compatibility H Sync V Sync Safety certification Operation temperature Dimensions W x H x D AC Input Power consumption Stand By Lamp Input Terminals Output Terminals Control Terminals Security SPECIFICATIONS H5080 Series TI DLP DMD 0 65 1920 x 1080 8 8 kg 19 lbs Standard Long Short 1 5 meters 7 meters 2 meters 20 meters 0 5 meters 3 meters 37 300 31 2 468 29 25 200 Manual Focus Manual Focus he Poon Manual Zoom Manual Zoom 1 25 1 5 Fix 15 degrees Front Rear Desktop Ceiling Rear Front VGA SVGA XGA SXGA SXGA UXGA Mac 4801 576i 576p 480p 720p 10801 1080p NTSC 4 43 PAL M N 60 SECAM 15 31 90 kHz 43 85 Hz FCC B UL cUL CB CE CCC KC PCT and C tick 5 40 C 431 mm x 181 mm x 344 mm 16 97 x
7. s Manual ITEM LABEL DESCRIPTION SEE PAGE 1 Poverorr 2 Hom2 Displays the HDMI 2 source selection 3 Displays the HDMI 3 source selection 4 Displays the VIDEO source selection Oo 0 Keystone Quick Menu For Keystone E Navigates and changes settings in the OSD 7 8 peas 9 ASPECTRATIO Displays the ASPECT RATIO selections 10 SOURCE Detects the input device re Displays the PC source selection az soeur Displays the brightness setting bar a3 snam Displays the sharpness setting bar 4 coon Displays the color setting bar as Displays the tint setting bar KEW E Makes the screen blank Freezes unfreezes the on screen picture an AUTO Auto adjustment for frequency phase and position mom Turns on or off the remote control backlight for about 10 seconds Pressing any LIGHT other key while the backlight is on keeps the backlight on for a further 10 sec onds 20 OVERSCAN Displays the Overscan selection 21 Displays the Gamma selection 22 Displays the Noise Reduction selection 23 CONTRAST Displays the contrast settings bar 24 PICTUREMODE Changes the 2 Mode setting as opsade os E E EII Displays the Component source selection Displays the S VIDEO source selection 29 HDMI Displays the
8. 7 13 x 13 54 AC Universal 100 240 Typical 110VAC 100 240 10 Standard mode 310W Boost mode 370W lt watt 280W Digital HDMI x 3 Analog RGB HD 15 x 1 Composite RCA x 1 Yellow S Video mini dim x 1 Component RCA x 3 DC_out screen trigger DC Jack x 2 DC12V 200mA output function RS 232 Keyboard Emulation Control USB connector type B Kensington lock 44 DLP Projector User s Manual Projection Distance vs Projection Size Image Hight SS a TET Projection Distance H5080 Series Projection Distance and Size Table Standard projection lens TR 1 54 1 93 TELE WIDE Distance m 1 28 3 42 4 27 8 55 1 36 2 73 341 10 23 Diagonal 9 30 80 100 200 40 80 100 300 9 93 9 93 9 93 9 93 12 39 12 39 12 39 12 39 Image Height mm 373 6 9962 12453 24905 4981 996 2 12453 3735 8 Image Width mm 6641 17710 2213 8 44276 8855 17710 2213 8 66414 A mm 374 99 6 124 5 249 1 49 8 99 6 124 5 373 6 Long throw projection lens TR 1 93 2 89 Distance m 3 20 5 12 6 40 25 59 2 14 3 42 427 1923 Diagonal 50 80 100 400 50 80 100 450 ue m 6 66 6 66 6 66 6 66 9 9 9 9 9 9 9 9 Image Height mm 622 6 9962 12453 49811 6226 9962 12453 5603 7 Image Width mm 11069 1771 0 2
9. Auto Power Off 4 Disable 5 Min 10 Min 15 Min 20 Min 25 Min 30 Min CIAO ae 4 Sleep Timer HH Disable 30 Min 1 Hr 2 Hr 3 Hr 4Hr 8Hr 12 Hr 4 Background Color HH Purple Black Black 1 Menu Settings Menu position _Top Left Top Right Center Bottom LefiBottom Right_ LH Menu Display Time _5 Sec 10 Sec 15 Sec 20 Sec 25Sec 30 Sec 4 Source KH PC 1 4 check uncheck F1 HDMI 1 HH check uncheck Hora check uncheck H HDMI 3 Component _ eneckuncheck H Video HH check uncheck HH S Video check uncheck Quick Auto Search On Off Lamp Lamp Mode KH Boost Standard H Reset Lamp Timer LM Yes No HDMI HDMI Format Auto PC Signal Video Signal H _ High Altitude 1 1 Off On HA Yes No Closed Caption Closed Caption Enable 1 1 Off Caption Version 1 2 3 4 LED Control KH Off Normal 12V Trigger 1 HH Off On 12VTrigger2 omon Reset All Enter Reset Cancel 23 DLP Projector User s Manual PICTURE gt gt Basic Menu Press the MENU button to open the OSD menu Press the cursor lt button to move to the PICTURE gt gt Basic menu Press the cursor A V button to move up and down in the PICTURE gt gt Basic menu Press lt gt to change values for settings Note Cu
10. Do not scratch the lens surface Work on a level surface with a soft cloth under it to avoid scratching f you remove and store the lens attach the lens cap to the projector to keep off dust and Removing the Existing Lens From the Projector 1 Pull and release the top cover to open as shown 2 Push the LENSE RELEASE button to the unlock position 3 Grasp the lens 4 Rotate the lens counterclockwise The existing lens will be disengaged 5 Pull out the existing lens slowly 13 DLP Projector User s Manual Installing the New Lens 1 Align the notches and correctly position the electrical contact pad as shown in the picture Note Pin of IRIS should be in the direction as shown in the picture 2 Rotate the lens clockwise until you feel it click into place 14 DLP Projector User s Manual Starting and Shutting down the Projector Starting the projector 1 Remove the lens cap Securely connect the power cord and signal cable When connected the power led will turn red u POWER Turn on the lamp by pressing button on the rear of the projector or 94 the remote control The PWR LED will now flash green The startup screen will display in ap proximately 30 seconds The first time you use the projector you can select your preferred language from quick menu after the startup screen display 15
11. HDMI source selection ewen 3 31 Transmits signals to projector DLP Projector User s Manual Remote Control Operating Range The remote control uses infrared transmission to control the projector It is not necessary to point the remote directly at the projector Provided you are not holding the remote perpendicular to the sides or the rear of the projector the remote will function well within a radius of about 7 meters 23 feet and 15 degrees above or below the projector level If the projector does not respond to the remote control move a little closer Projector and Remote Control Buttons The projector can be operated using the remote control or the buttons on the top of the projector All operations can be carried out with the remote control however the buttons on the projector are lim ited in use 10 DLP Projector User s Manual SETUP AND OPERATION Inserting the Remote Control Batteries 1 Remove the battery compartment cover by sliding the cover in the direction of the arrow 2 Insert the battery with the positive side facing up 3 Replace the cover Caution 1 Only use AA batteries Alkaline batteries are recommended 2 Dispose of used batteries according to local ordinance regulations 3 Remove the batteries when not using the projector for prolonged periods 11 DLP Projector User s Manual Connecting Input Device
12. N ZdAO4GI 40 IMAGE tirer or ER Fer ee e ERa ER 4 LAMP PROBLEMS 3 6 ve Dd ta E er Oe t eee p eH dE eR 4 REMOTE CONTROL PROBLEMS sscsessssecececseseseceeececsessaeceseeeceeseunaeeeeeceesesnsuesecscecseseuaeeecececseeuaeseeececsessaasaeeececeesenstaeeeeeees 42 HAVING THE PROJECTOR SERVICED enne enhn nnne enne tern nsns ss ss en sete tease sese assess ener tensa 42 HDMIO a Ai A NA AA EA died 43 SPECIFICATIONS I RE 44 SPECIFICATIONS A O A 44 PROJECTION DISTANCE VS PROJECTION SIZE cccccccccecsesssceccceceesesseceseecceesenseseceecccesesnsaeseeececseaaeceeccecsessaaeeeeceecsensaeaeeeeeees 45 H5080 Series Projection Distance and Size eese nennen entren 45 H5080 SERIES TIMING MODE TABLE cese e nnnm en teth nnns sien entera ss esset 46 PROJECTOR E DI IVI 49 REGULATORY COMPLIANCE cisccsscecsssssccssscsccsciscesssssesovsacsesevscesecdcassceceossscossssectessessscncdeseseoseusesbsdscdesdesossssseseeesiesessess 50 50 e II EE 50 SAFETY CERTIFICA TON San 50 yi DLP Projector User s Manual GETTING STARTED Packing Checklist Carefully unpack the projector and check that
13. Shift Lever Vertical Lens Shift Lever The Shift feature provides a lens shift function that can be used to adjust the position of the projected image either horizontally or vertically within the range detailed below Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio than traditional lens shift systems Adjusting the vertical image position The vertical image height can be adjusted between 120 and 40 of half image height Note that the maximum vertical image height adjustment can be limited by the horizontal image position For example it is not possible to achieve the maximum vertical image position height detailed above if the horizontal image position is at maximum Please consult the Shift Range diagram below for further clarification SEE 40 offset pamm 0 offset Screen Height 120 offset 18 DLP Projector User s Manual Adjusting the horizontal image position With the lens in the center position the horizontal image position can be adjusted to the left or right by up to a maximum of 10 of the half image width Note that the maximum horizontal image height ad justment can be limited by the vertical image position For example it is not possible to achieve the maximum horizontal image position if the vertical image position is at maximum Please consult the Shift Range diagram below for further clarification Screen Widt
14. Vertical Position Press the lt P buttons to adjust the display position up or down 28 DLP Projector User s Manual SETUP gt gt Basic Menu Press the MENU button to open the OSD menu Press the cursor lt button to move to the SETUP gt gt Basic menu Press the cursor A V button to move up and down in the SETUP gt gt Basic menu Press to change values for settings Language Splash Logo Projection Blank Timer Auto Power Off Sleep Timer Background Color Menu Settings m g SETUP gt gt Basic i Language English Splash Logo VIVITEK Projection Front Table Blank Timer Disable y Auto Power Off 20 Min Sleep Timer 30 Min Background Color Purple 3 Menu Settings 1 AS Source DESCRIPTION Press the cursor lt gt buttons to select a different localization menu Range English Danish Dutch Finnish French German Italian Japanese Ko rea Norwegian Polish Portuguese Russian Traditional Chinese Simplified Chinese Spanish Swedish Press the cursor lt buttons to select a different startup screen Range Vivitek Blue Black Press the cursor lt buttons to choose from four projection methods Front Table Front Ceiling Rear Table Rear Ceiling Press the cursor buttons to set the Blank Screen timer The projected image is automati cally restored after the set time Range Disable 5 min 10 min 15 min 20 min 25 min 30 min Press the
15. at least 30 minutes before cleaning Failure to do so could result in a severe burn 2 Use only a dampened cloth when cleaning Do not allow water to enter the ventilation openings on the projector 3 If a little water gets into the projector interior while cleaning leave unplugged a well ventilated room for several hours before using 4 If a lot of water gets into the projector interior when cleaning have the projector serviced Cleaning the Lens You can purchase optic lens cleaner from most camera stores Refer to the following to clean the pro jector lens 1 Apply a little optic lens cleaner to a clean soft cloth Do not apply the cleaner directly to the lens 2 Lightly wipe the lens in a circular motion Caution 1 Do not use abrasive cleaners or solvents 2 To prevent discoloration or fading avoid getting cleaner on the projector case Cleaning the Case Refer to the following to clean the projector case 1 Wipe off dust with a clean dampened cloth 2 Moisten the cloth with warm water and mild detergent such as used to wash dishes and then wipe the case 3 Rinse all detergent from the cloth and wipe the projector again Caution To prevent discoloration or fading of the case do not use abrasive alcohol based cleaners 37 DLP Projector User s Manual Using the Physical Lock Using the Kensin gton Lock If you are concerned about security attach the projecto
16. cursor gt buttons to set the Auto Power Off timer The projector automatically turns off if no input source is detected after the preset period of time Range Disable 5 min 10 min 15 min 20 min 25 min 30 min Press the cursor lt gt buttons to set Sleep timer The projector automatically turns off after the preset period of time Range Disable 30 min 1hr 2hr 3hr 4hr 8hr 12hr Press the cursor lt P buttons to select the background color when no input source is detected Range Purple Black Blue Press the ENTER button to enter the Menu Settings sub menu See Menu Settings on page 30 Press the ENTER button to enter the Source sub menu See Source on page 30 29 DLP Projector User s Manual Menu Settings Press the ENTER button to enter the Menu Settings sub menu Menu Settings Menu Position CCN Menu Display Time ITEM DESCRIPTION Menu Position Press the lt buttons to select from five OSD locations Top Left Top Right Center Bottom Left Bottom Right Menu Display Time Press the lt P buttons to set the Menu Display timer before the OSD times out Range 5sec 10sec 15sec 20sec 25sec 30sec Source Press the ENTER button to enter the Source sub menu Source PC HDMI 1 HDMI 2 HDMI 3 Component Video S Video Quick Auto Search lt lt lt lt lt DESCRIPTION C Press the lt 4 gt buttons to enable or disable the PC source
17. dd 29 A A O NR 30 NN 30 SETUP gt gt ADVANCED MENU ccccccccccecssssssececececsessssscecececsesssaececececsessaaececececsenesasceeececsesesaseeeeeecsesesasseeececseseaaaaeeeeeceeneneaeees 31 VEO AEE EN 32 32 Closed COP ON 33 TEALRO EI E E E 33 STATUS 34 MAINTENANCE AND SECURITY eere oe ees sete ees ranae VE ro ae dene E Ten Ga aee Po EN NE aepo Fa eU ae Enea e EET PN 35 REPLACING THE PROJECTION LAMP 2 ii 35 CLEANING THE PROJECTOR sco sve ise co eve Ere dere ticas 37 CGle nine the E CREER RII E 37 Cleaning the Case a o aduer doas A Tel clade didi ls ens Tad 37 USING THE PHYSICAL LORA Kats eco rei ub du vec ed dv ER dus 38 Using the Kensington Lock mene a Eee ae Re DEL M M a 38 Using the Security Chain Lok aiii id 38 DLP Projector User s Manual TROUBLESHOOTING em 39 COMMON PROBLEMS AND SOLUTIONS ccccessesseceeeceesesssececeeecceseseaeeecececeesssueseescceseausaesecececeeseaueseeeccesesssasaeeececeesensnaeeeeeens 39 TIPS FOR TROUBLESHOOTING ccecsessscecececeessueceeececsesssusceceecccevenseaeeesecsesesuseseescecseeaaececececsesaaeeeescecseseaaseecececeessaasaeneeeens 39 LED ERROR MESSAGES RRRRRRRRRRRRRRRRRRRRRRRRRRRRRMMMMMMMMMMEMEMMMMMMEMMMMMMMMMMMMEMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMWMK
18. is configured for an external display This is usually done by pressing a Fn key combination on the notebook Tips for Troubleshooting In each problem specific section try the steps in the order suggested This may help you to solve the problem more quickly Try to pin point the problem and thus avoid replacing non defective parts For example if you replace batteries and the problem remains put the original batteries back and go to the next step Keep a record of the steps you take when troubleshooting The information may be useful when call ing for technical support or for passing on to service personnel DLP Projector User s Manual LED Error Messages POWERLED READY LED TEMP LED ERROR CODE MESSAGES BLINK BLINK BLINK Lamp Ready ON ON OFF Start ON OFF OFF Cooling ON FLASHING OFF Over temperature OFF OFF ON Thermal Break Sensor error 4 4 OFF Lamp End of lamp life detected 5 3 OFF Burner Fan error 6 1 OFF Lamp Fan error 6 2 OFF Power Fan error 6 3 OFF DMD Fan error 6 4 OFF Case Open 7 OFF OFF DMD error 8 OFF OFF Color wheel error 9 OFF OFF In the event of an error please disconnect the AC power cord and wait for one 1 minute before re starting the projector If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit contact your service center 40 DLP Projector User s Manual Image Problems Problem No image appears o
19. re ER E aed v c n 2 H3080 Series BronEright VIEW aui A de eo od td 2 Top view On screen Display OSD buttons and LEDS 4 INTTR 5 EE 7 REMOTE CONTROL PARTS ccccccccccssssssscecececeessececececsessscaececececsensuaeeeeecscsensaaeseeesecsessaaececececeesenseaeceesesesesaaeceseeeesensaaeeeeeeecns 8 REMOTE CONTROL OPERATING RANGE ccccsesssceeececsesssececececseseseeecececeenesaseseeeceesesusaesecececsesssuececececsesaaeeeeeeecseneasaeeeeees 10 PROJECTOR AND REMOTE CONTROL BUTTONS ccccsessscesececsesessececececeesensesecececeeseasesecececsesaueseeccecsessaaeeeeceecsensaeaeeeeeees 10 SETUP AND OPERATION 11 INSERTING THE REMOTE CONTROL BATTERIES EKSS KA EEO KENEEN ES 11 CONNECTING INPUT DEVICES itcr reve n eee er et eb ue E e e eed 12 INSTALLING OR REMOVING THE OPTIONAL LENS cssssscesececeesssseseeececsesessneececececsensnaececececsessuaeseeeecesensuaeeetececseseneeaeteeeens 13 Removing the Existing Lens From the Projector sese eene eene nennen rennen nee enne 13 Installing ihe New Lens aio ooo adh ur YD do Dae dod Qa Ras 14 STARTING AND SHUTTING DOWN THE PROJECTOR cccccsesssseceeececsessnaececececsesesesetececsesssseeececseceseseaetece
20. the following items are included REMOTE CONTROL VGA CABLE COMPONENT CABLE POWER CORD WITH TWO AA BATTERIES QUICK START CARD Warranty Card HDMI CABLE CD ROM WARRANTY CARD QUICK START CARD THIS USER S MANUAL Contact your dealer immediately if any items are missing appear damaged or if the unit does not work It is recommend that you keep the original packing material should you ever need to return the equipment for warranty service Caution Avoid using the projector in dusty environments DLP Projector User s Manual Views of Projector Parts H5080 Series Front right View ITEM LABEL DESCRIPTION SEE PAGE x e CT 18 EE Height adjuster Adjusts level of projector See Top view On screen Display OSD buttons 8 Vertical lens shift Adjusts the image position vertically DLP Projector User s Manual DESCRIPTION SEE PAGE NES Horizontal lens shift Adjusts the image position horizontally Important Ventilation openings on the projector allow for good air circulation which keeps the projector lamp cool Do not obstruct any of the ventilation openings LABEL DLP Projector User s Manual Top view On screen Display OSD buttons and LEDs MENU 2 3 6 7 5 8 9 SOURCE SEE PAGE ITEM LABEL DESCRIPTION A Up cursor Navigates and changes settings in the OSD Keystone Quick Menu For Keystone 3 Enter
21. 213 8 88552 11069 17710 2213 8 9962 1 A mm 62 3 99 6 124 5 498 1 62 3 99 6 1245 5604 Short throw projection lens TR 0 77 Distance m 0 5 1 4 3 0 34 Diagonal 30 80 175 200 7 24 1 24 1 24 1 24 1 Image Height mm 373 6 9962 21792 2490 5 Image Width mm 6641 1771 0 38742 44276 A mm 374 99 6 217 9 2491 45 DLP Projector User s Manual H5080 Series Timing Mode Table The projector can display several resolutions The following table outlines the resolutions that can be displayed by the projector SIGNAT RESOLUTION V SYNC COMPOSITE COMPONENT RGB HDMI KHz Hz S VIDEO ANALOG DIGITAL VGA 640 x 350 31 5 70 1 O O 640 x 350 37 9 85 1 O O 720 x 350 31 5 70 0 O O 640 x 400 37 9 85 1 O O 720 x 400 31 5 70 0 O O 720 x 400 37 9 85 0 O O 720 x 400 39 4 87 8 O O 640 x 480 37 5 75 0 O O 640 x 480 43 3 85 0 O O 800 x 600 48 1 72 2 O O 800 x 600 50 3 80 O O 800 x 600 53 7 85 1 O O 1024 x 576 29 6 50 O O 1024 x 576 35 8 60 O O 1024 x 768 60 0 75 0 O O VESA DMT 1024 x 768 68 7 85 0 O O 1152 x 864 54 3 60 0 O O 1152 x 864 63 9 70 0 O O 1152 x 864 67 5 75 0 O O 1152 x 864 73 5 85 0 O
22. 35 0 66 7 O O E 832 x 624 49 7 74 5 1024 x 768 60 2 74 9 O O 1152 x 870 68 7 75 1 O O a o a a PAL RE EM Sub carrier Frequency O 2 e 2 SECAM frequency O 10 480i 15 8 60 0 O SDTV 576i 15 6 50 0 O 480 31 5 60 0 O EDTV 576p 31 3 50 0 O 47 DLP Projector User s Manual SIGNAL RESOLUTION H SyNc V SYNC COMPOSITE COMPONENT RGB HDMI KHz Hz S VIDEO ANALOG DIGITAL 720p 45 0 60 0 O 2 O 720p 375 50 0 O 10801 33 8 60 0 2 O 1080i 28 1 50 0 a O HDTV 1080p 27 24 O O 1080p 28 125 25 O 2 O 1080p 33 75 30 O 1080p 56 25 50 O 1080p 67 5 60 O O Frequency supported Frequency not supported The native resolution of the panel for the H5080 series is 1920 x 1080 Resolution other than native resolution may display with uneven size of text or lines 48 DLP Projector User s Manual Projector Dimensions 431mm 1 16 97 323 26 12 73 344mm 13 54 161 51mm 6 36 181mm 7 13 49 DLP Projector User s Manual REGULATORY COMPLI
23. ANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pur suant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communica tions Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense Changes or modifications not expressly approved by the parties responsible for compliance could void the user s authority to operate the equipment Canada This class B digital apparatus complies with Canadian ICES 003 Safety Certifications FCC B UL cUL CB CE CCC KC PCT and C tick 50
24. Copyright This publication including all photographs illustrations and software is protected under international copy right laws with all rights reserved Neither this manual nor any of the material contained herein may be reproduced without written consent of the author Copyright 2009 Disclaimer The information in this document is subject to change without notice The manufacturer makes no represen tations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose The manufacturer reserves the right to revise this publi cation and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes Trademark Recognition Kensington is a U S registered trademark of ACCO Brand Corporation with issued registrations and pend ing applications in other countries throughout the world All other product names used in this manual are the properties of their respective owners and are acknowl edged DLP Projector User s Manual Important Safety Information Important It is strongly recommended that you read this section carefully before using the projector These safety and usage instructions will ensure that you enjoy many years of safe use of the projector Keep this manual for future reference Symbols Used Warning symbols are used on the u
25. O 1280 x 720 37 5 50 O O 1280 x 720 45 60 O O 1280 x 1024 64 0 60 0 O O 1280 x 1024 80 0 75 0 O O 1280 x 1024 91 1 85 0 O O 1600 x 1200 75 0 60 0 O O 1920 10801 33 8 60 0 O O 1920 10801 28 1 50 0 O O 1920 x 1080p 27 24 O O 1920 x 1080p 56 25 50 O O 1920 x 1080p 67 5 60 O O CGA84 640 x 400 31 5 70 1 O O 640 480 31 5 60 0 O O 640 x 480 34 9 66 6 O O 46 DLP Projector User s Manual SICNAL RESOLUTION H SYNC V SyNC COMPOSITE RGB HDMI KHz 7 S VIDEO ANALOG DIGITAL 640 x 480 37 9 72 8 O O 800 x 600 35 2 56 3 O O 800 x 600 37 9 60 3 O O VESA 800 x 600 46 9 75 0 O O 1024 x 768 48 4 60 0 1024 x 768 56 5 70 1 O O 1024 x 768 577 72 O O 1280 x 720 56 4 75 O O 1280 x 720 64 4 85 O O 1280 x 768 47 4 60 0 1280 768 56 70 0 O O 1280 x 768 60 3 75 0 O O 1280 x 768 68 8 85 0 O Dum 1280 x 800 49 7 60 O O 1400 x 1050 64 7 60 0 O O 720 x 480i 15 8 60 0 O O 720 x480p 31 5 60 0 O O 720 x576i 15 6 50 0 720 576 31 3 50 0 O O 1280 x 720p 45 0 60 0 O O 1280 x 720p 37 5 50 0 O O CVT 1920 x 1200 74 0 60 0 O 640 x 480
26. T CONTRAST BRIGHT SHARP OVERSCAN LIGHT AUTO 4 GAMMA FREEZE BLANK BA SOURCE 1 To enter the OSD press the MENU button PICTURE gt gt Basic 2 There are six menus Press the cur Display Mode User 1 sor lt P button to move through the ACH menus 3 Press the cursor A V button to move up and down in a menu Sharpness 4 Press 4 to change values for set E 4 I Save Setting tings A E Reset Picture Settings 5 Press MENU to close the OSD or leave a sub menu Note Depending on the video source not all items in the OSD are available For example the PC Detail Adjustment tem in the PICTURE gt gt Basic menu can only be modified when connected to a PC Items that are not available cannot be accessed and are grayed out DLP Projector User s Manual Setting the OSD Language Set the OSD language to your preference before continuing 1 Press the MENU button Press the cursor lt gt button to navigate to SETUP gt gt Basic GEM SETUP gt gt Basic i Language English Splash Logo VIVITEK Projection Front Table 4 Blank Timer Disable ty Auto Power Off 20 Min Sleep Timer 30 Min Background Color Purple Menu Settings 1 Source 2 Press the cursor A V button until Language is highlighted 3 Press the cursor button until the language you want is selected 4 Press the MENU butto
27. ed Caption sub menu Closed Caption Closed Caption Enable On Caption Version GGI ITEM DESCRIPTION Closed Caption Enable Press the lt gt buttons to turn on or off Closed Caption Press the lt P buttons to select the Caption Version 12V QUT A Set 12V OUT A to On to enable the projector to automatically lower the projection screen when pow ering on When powering off screen trigger stops sending a low voltage trigger to the screen controller and the screen goes up H SETUP gt gt Advanced Lamp lt HDMI High Altitude Mode Closed Caption ED Control Normal 12V OUT A On 12V On Lens Type Standard 3 Reset All 33 DLP Projector User s Manual STATUS Menu Press the MENU button to open the OSD menu Press the cursor lt button to move to the STATUS Menu EM STATUS Source Resolution 1280 x 1024 75Hz Lamp Hour Firmware Version PWMOO1 ITEM DESCRIPTION Note Status displayed in this menu is for viewing only and cannot be edited 34 DLP Projector User s Manual MAINTENANCE AND SECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out It should only be replaced with a certified replacement part which you can order from your local dealer Important a The projection lamp used in this product contains a small amount of mercury b Do not dispose this product with general house
28. esesessaeseeseeesenseatees 15 Starting the projector aua 15 Sh t ng down the Projector da de 16 ADJUSTING THE PROJECTOR LEVEL b EN e eer er 17 ADJUSTING PROJECTED IMAGE POSITION USING SHIFT cccccccccccecsessseceeececsesseseceeececseseaececececeesssaesecececsessaseeeeeeceesenseaeees 18 Adjusting the vertical image 5 18 Adjusting the horizontal image position 19 Shift RANGE DIG BION PC 19 ADJUSTING THE ZOOM RING FOCUS AND KEYSTONE csssssssseeececsessssecececcesenseascecececsesnsaeceeececseseanseeeececseseasaeeeeceeenensaaeees 20 ON SCREEN DISPLAY OSD MENU SETTINGS cccsssssssssssecssscssssessscsssscsssccssnassesscessessssccssassssscssasssssssseassosss 21 OSD MENU CONTROLS c 21 Navigating the 0 EH ERU 21 SETTING THE OSD LANGUAGE ME 22 OSD MENU OVERVIEW 23 PICTURES BASIC MENU 24 PIG TURE gt ADVANGED MENU errira e eee a 25 SCA US MEN al oss ban ads Made dee ER 26 VIIS CHINOS M 26 DISPLAY MENU nece t ea ade tadas 27 Detail Adjusimehtss A di 28 SETUP gt gt BASIC
29. fore cleaning See Cleaning the Projector on page 37 Allow the lamp to cool for about one hour Regulatory Warnings Before installing and using the projector read the regulatory notices in the Regulatory Compliance section on page 50 Important Recycle Instructions Lamp s inside this product contain mercury This product may contain other electronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG Symbol Explanations DISPOSAL Do not use household or municipal waste collection services for disposal of electrical and electronic equipment EU countries require the use of separate recycling collection services About this manual This manual is intended for end users and describes how to install and operate the DLP projector Wherever possible relevant information such as an illustration and its description has been kept on one page This printer friendly format is both for your convenience and to help save paper thereby protecting the environ ment It is suggested that you only print sections that are relevant to your needs Table of Contents GETTING STARTED IC 1 PAGKING C HECKUIS Ts n rave i PL LE e P ebbe t 1 VIEWS OF PROJECTOR PARTS ces ra tere eee eo ede
30. h W Q 9 vivitek Left Side Right Side W 2 x 10 10 Shift Range Diagram Hx120 Hx100 H Image Height image shift Hx120 Max W image shift Ww 10 When Wx10 Max image shift Hx100 WhenHx120 Max image shift Wx0 DLP Projector User s Manual Adjusting the Zoom ring Focus and Keystone 1 Use the Image zoom control on the projector only to resize the pro jected image and screen size 2 Use the Image focus control on the projector only to sharpen the pro jected image 3 Use the KEYSTONE buttons on the projector or the remote control to correct image trapezoid wider top or bottom effect 1 1 MODE SOURCE fomes mem soe NR COLOR TINT SOURCE GAMMA FREEZE BLANK Remote control and OSD panel 4 The keystone control appears on the display P Y Keystone 0 20 DLP Projector User s Manual ON SCREEN DISPLAY OSD MENU SETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings Navigating the OSD You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD The following illustration shows the corresponding buttons on the projector SOURCE PC PICTURE E J NR COLOR TIN
31. he ceiling mount must be of a suitable shape and strength The ceiling mount load capacity must exceed the weight of the installed equipment and as an additional precaution be capable of withstanding three times the weight of the equipment not less than 5 15 kg over a period of 60 seconds DLP Projector User s Manual Remote Control Parts 30 48 amp 1 1 SOURCE 7 2 29 HOM 28 15 ad ad 27 COMP S VIDEO VIDEO 4 jm 1 8 T PICTURE 1 0 24 gt MODE SOURCE PC a 11 23 CONTRAST BRIGHT mn o 15 1 i 14 22 NR COLOR 15 21 Gamma FREEZE EN 16 20 OVERSCAN LIGHT AUTO 1 8 19 vivitek Important 1 Avoid using the projector with bright fluorescent lighting turned on Certain high frequency fluo rescent lights can disrupt remote control operation 2 Be sure nothing obstructs the path between the remote control and the projector If the path be tween the remote control and the projector is obstructed you can bounce the signal off certain reflective surfaces such as projector screens 3 The buttons and keys on the projector have the same functions as the corresponding buttons on the remote control This user s manual describes the functions based on the remote control DLP Projector User
32. hold waste c Disposal of this product must be carried out in accordance with the regulations of your local authority Warning Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp Failure to do so could result in a severe burn 1 Switch off the power to the projector by pressing the POWER button 2 Allow the projector to cool down at least 30 minutes Ce 12VOUTA 12VOUTB 3 Disconnect the power cord 4 Unlock the lamp cover 5 Pull up and remove the cover DLP Projector User s Manual 6 Use a screwdriver to remove the screws from the lamp module 7 Pull out the lamp module 8 Reverse steps 1 to 7 to install new lamp module While installing align the lamp module with the connector and ensure it is level to avoid damage Note The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws 9 Turn on the projector and reset the lamp after the lamp module is replaced Lamp Reset Press Menu Select SYSTEM SETUP Advanced Select Lamp Select Lamp Mode or Reset Lamp Timer Press the buttons to adjust the settings 36 DLP Projector User s Manual Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble free operation Warning 1 Be sure to turn off and unplug the projector
33. hould the projector be installed in any way other than the desktop and ceiling mount otherwise lamp life could decrease dramatically x x Minimum 500mm Minimum 500mm _ i Minimum 500mm Minimum 300mm gt Ensure that the intake vents do not recycle hot air from the exhaust vent gt When operating the projector in an enclosed space ensure that the surrounding air temperature within the enclosure does not exceed operating temperature while the projector is running and the air intake and exhaust vents are unobstructed gt All enclosures should pass a certified thermal evaluation to ensure that the projector does not recycle exhaust air as this may cause the device to shutdown even if the enclosure temperature is with the acceptable operating temperature range Power Safety gt Only use the supplied power cord gt not place anything on the power cord Place the power cord where it will not be in the way of foot traffic Remove the batteries from the remote control when storing or not in use for a prolonged period iii DLP Projector User s Manual Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly See Replacing the Projection Lamp on page 35 for clear and safe instructions for this procedure Before replacing the lamp gt Unplug the power cord gt Allow the lamp to cool for about one hour Cleaning the Projector gt Unplug the power cord be
34. le Recently HDMI Licensing LLC announced that cables would be tested as Standard or High Speed cables e Standard or category 1 HDMI cables have been tested to perform at speeds of 75Mhz up to 2 25Gbps which is the equivalent of a 720p 1080i signal High Speed or category 2 HDMI cables have been tested to perform at speeds of 340Mhz or up to 10 2Gbps which is the highest bandwidth currently available over an HDMI cable and can successfully handle 1080p signals including those at increased color depths and or increased refresh rates from the Source High Speed cables are also able to accommodate higher resolution displays such as WQXGA cinema monitors resolution of 2560 x 1600 How do I run HDMI cables longer than 10 meters There are many HDMI Adopters working on HDMI solutions that extend a cable s effective distance from the typical 10 meter range to much longer lengths These companies manufacture a variety of solutions that include active cables active electronics built into cables that boost and extend the cable s signal repeaters amplifiers as well as CAT5 6 and fiber solutions How can 1 tell if a cable is an HDMI certified cable All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance Test Specification However there may be instances where cables bearing the HDMI logo are available but have not been properly tested HDMI Licensing LLC actively
35. lect the LED control Select Normal for normal LED display and Off to disable LED display Press the cursor lt buttons to turn on or off 12V OUT A High Altitude Mode 12V OUT A When connected to the screen through a commercially available cable the screen deploys automatically on start up of the projector The screen retracts when the projector is powered off 12V OUT B Press the cursor lt gt buttons to turn on or off 12V OUT B Lens Press the cursor lt buttons to select a lens type Range Short Standard Long Reset All Press the ENTER button to enter reset all settings to default values 31 DLP Projector User s Manual Lamp Press the ENTER button to enter the Lamp sub menu Lamp Lamp Mode Standard Reset Lamp Timer Lamp Hour ITEM DESCRIPTION Lamp Mode Press the lt P buttons to adjust lamp brightness Reset Lamp Timer Press the ENTER button to reset the Lamp Hour after the lamp is replaced Displays the number of hours the lamp has been in use HDMI Press the ENTER button to enter the HDMI sub menu HDMI HDMI Format Auto HDMI Amplifier Gain 3 ITEM DESCRIPTION Press the gt gt buttons to select from three HDMI display formats Auto PC signal Video signal HDMI Amplifier Gain Press the lt P buttons to adjust HDMI Amplifier Gain 32 DLP Projector User s Manual Closed Caption Press the ENTER button to enter the Clos
36. lting in a better black level and incredible detail Range Cinema 1 Cinema 2 Off Press the cursor gt button to adjust the IRIS IRIS Range to 9 EE Press the ENTER button to enter the ViviSettings sub menu ViviSettings E See ViviSettings on page 26 25 DLP Projector User s Manual HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu HSG Adjustment Primary Color R Hue 0 Saturation 100 Gain 100 ITEM DESCRIPTION Primary Color Press the lt P buttons to set the Primary Color Notes There are six sets R G B C M Y of colors to be customized Press the lt P buttons to adjust the Hue Press the lt P buttons to adjust the Saturation Press the lt gt buttons to adjust the Gain ViviSettings Press the ENTER button to enter the ViviSettings sub menu ViviSettings ViviMotion ViviPeaking Flesh Tone ITEM DESCRIPTION ViviMotion Press the lt P buttons to select different MEMC level Range Off Low Medium High ViviPeaking Press the lt P buttons to adjust motion adaptive sharpness enhancement 2D Peaking value Range 0 to 3 Press the lt P buttons to select different Flesh Tone Range 0 to 5 Notes This function is only available when Component Video or S Video input source is selected Flesh Tone 26 DLP Projector User s Manual DISPLAY Menu Press the MENU button to open the OSD menu Press the cursor l
37. n the screen 1 Verify the settings on your notebook or desktop PC 2 Turn off all equipment and power up again in the correct order Problem The image is blurred 1 Adjust the Focus on the projector 2 Press the Auto button on the remote control or projector 3 Ensure the projector to screen distance is within the 10 meter 33 feet specified range 4 Check that the projector lens is clean Problem The image is wider at the top or bottom trapezoid effect 1 Position the projector so it is as perpendicular to the screen as possible 2 Use the Keystone button on the remote control or projector to correct the problem Problem The image is reversed Check the Projection setting on the Installation menu of the OSD Problem The image is streaked 1 Set the Frequency and Tracking settings on the Computer menu of the OSD to the de fault settings 2 To ensure the problem is not caused by a connected PC s video card connect to another computer Problem The image is flat with no contrast Adjust the Contrast setting on the Image menu of the OSD Problem The color of the projected image does not match the source image Adjust the Color Temperature and Gamma settings on the Image menu of the OSD Lamp Problems Problem There is no light from the projector 1 Check that the power cable is securely connected Ensure the power source is good by testing with another electrical device Restart the projector in the correct order and check tha
38. n to close the OSD 22 DLP Projector User s Manual OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting PICTURE gt gt Advanced HSG Adjustment Display Movie Bright Normal User 1 User 2 User 3 ISF Day ISF Night User Mode Movie Bright Normal Save Setting I Reset Picture Setting __ Noise Reduction Yes No H _ Color Temperature Lamp Native Warm Normal Cool Cooler High Cool Color Gamut 4 Native Cinema HDTV EBU STMPE C __HSG Adjustment Color Space H Auto RGB STDV HDTV DynamicBlack HH OffiCinema 1 Cinema 2 RS 7 ViviSet ing ViviPeaking Flesh Tone Sturation Off Low Medium High DISPLAY AspectRaio 1 Auto 16 9 4 3 Letter Keystone Overscan l Overscan PC Detail Adjustment English Danish Dutch Finnish French German Italian Japanese Korea Norwegian Polish Portuguese Russian Traditional Chinese Simplified Chinese Auto Frequency Phase Horizontal Position Vertical Position Spanish Swedish Splash Logo HH VIVITEK Blue Black Blank Timer 1 4 Projection HH Front Table Front Ceiling Rear Table Rear Ceiling Disable 5 Min 10 Min 15 Min 20 Min 25 Min 30 Min 4
39. nit and in this manual to alert you of hazardous situations The following styles are used in this manual to alert you to important information Note Provides additional information on the topic at hand Important Provides additional information that should not be overlooked Caution Alerts you to situations that may damage the unit Warning Alerts you to situations that may damage the unit create a hazardous environment or cause per sonal injury Throughout this manual component parts and items in the OSD menus are denoted in bold font as in this example Push the MENU button on the remote control to open the DISPLAY menu General Safety Information gt Do not open the unit case Aside from the projection lamp there are no user serviceable parts in the unit For servicing contact qualified service personnel gt Follow all warnings and cautions in this manual and on the unit case The projection lamp is extremely bright by design To avoid damage to eyes do not look into the lens when the lamp is on gt Do not place the unit on an unstable surface cart or stand Avoid using the system near water in direct sunlight or near a heating device gt Do not place heavy objects such as books or bags on the unit Preface Projector Installation Notice gt Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees nor s
40. ot pressed the message will disappear in 5 seconds The cooling fans continue to operate for about 60 seconds for cooling cycle and the PWR LED will turn or ange When the light is solid orange the projector has entered standby mode If you wish to turn the projector back on you must wait until the projector has completed the cooling cycle and has entered standby mode Once in standby mode simply press button on the rear of the projec tor or on the remote control to restart the projector Disconnect the power cord from the electrical outlet and the projector Do not turn on the projector immediately following a power off procedure 16 DLP Projector User s Manual Adjusting the Projector Level Take note of the following when setting up the projector The projector table or stand should be level and sturdy Position the projector so that it is perpendicular to the screen Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle Ensure the cables are in a safe location You could trip over them 1 raise the level of the projector twist the adjusters clockwise 2 To lower the level of the projector lift the projector and twist the adjusters counter clockwise 27 17 DLP Projector User s Manual Adjusting Projected Image Position Using Shift Lens Release Horizontal Lens
41. r to a permanent object with the Kensington slot and a security cable Note Contact your vendor for details on purchasing a suitable Kensington security cable The security lock corresponds to Kensington s MicroSaver Security System If you have any com ment contact Kensington 2853 Campus Drive San Mateo CA 94403 U S A Tel 800 535 4242 http www Kensington com Using the Security Chain Lock In addition to the password protection function and the Kensington lock the Security Chain Opening helps protect the H5080 from unauthorized use See the following picture 38 DLP Projector User s Manual TROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector If the problem remains unsolved contact your dealer for assistance Often after time spent troubleshooting the problem is traced to something as simple as a loose con nection Check the following before proceeding to the problem specific solutions e Use some other electrical device to confirm that the electrical outlet is working e Ensure the projector is turned on e Ensure all connections are securely attached e Ensure the attached device is turned on e Ensure a connected PC is not in suspending mode e Ensure a connected notebook computer
42. s A PC or notebook computer and video devices can be connected to the projector at the same time Video devices include DVD VCD and VHS players as well as movie camcorders and digital still cameras Check the user manual of the connecting device to confirm it has the appropriate output connector ITEM LABEL DESCRIPTION Om M wm _ eme LS When connected to the screen through a commercially available cable the 12V OUT A B screen deploys automatically on start up of the projector The screen retracts when the projector is powered off TN em ETT Warning As a safety precaution disconnect all power to the projector and connecting devices before making connections DLP Projector User s Manual Installing or Removing the Optional Lens Caution Do not shake or place excessive pressure on the projector or the lens components as the projec tor and lens components contain precision parts Before removing or installing the lens be sure to turn off the projector wait until the cooling fans stop and turn off the main power switch e Do not touch the lens surface when removing or installing the lens e Keep fingerprints dust or oil off the lens surface
43. stomizing the settings in PICTURE gt gt Basic menu is only available in User 1 2 3 mode Display Mode User Mode Brightness Contrast Color Sharpness Save Setting Reset Picture Settings PICTURE gt gt Basic Display Mode User 1 User Mode Normal Brightness Contrast Color Tint harpness Save Setting B Reset Picture Settings iit DESCRIPTION Press the cursor lt P buttons to set the Display Mode Range Movie Bright Normal User 1 User 2 User 3 Notes ISF Day ISF Night is available when ISF Mode is on Press the cursor lt buttons to set the User Mode Range Movie Bright Normal Press the cursor lt gt buttons to adjust the display brightness Press the cursor lt buttons to adjust the display contrast Press the cursor lt buttons to adjust the video saturation Notes This function is only available when Component Video or S Video input source is selected Press the cursor lt gt buttons to adjust the video tint hue Notes This function is only available when Component Video or S Video with NTSC system input source is selected Press the cursor lt 4 gt buttons to adjust the display sharpness Notes This function is only available when Component Video or S Video input source is selected Press the ENTER button to save all settings Press the ENTER button to reset all settings to default values 24 DLP Projector User s Manual
44. t button to move to the DISPLAY menu Press the cursor A V button to move up and down in the DISPLAY menu Press 4 to change values for settings DISPLAY Aspect Ratio Keystone a Overscan d PC Detail Adjustment ITEM DESCRIPTION Aspect Ratio Press the cursor lt P button to set the Aspect Ratio P Range Auto 16 9 4 3 Letter Box Real Kevsto e Press the cursor lt button to adjust the Keystone y Notes This function 1s available when the Auto keystone function is turned off Press the cursor lt P button to adjust the Overscan Press the ENTER button to enter the PC Detail Adjustment sub menu PO Detil Aditeiment See PC Detail Adjustment on page 28 27 DLP Projector User s Manual PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu Note Customizing the settings in PC Detail Adjustment menu is only available when PC input source analog RGB is selected PC Detail Adjustment Auto Frequency Phase Horizontal Position Vertical Position ITEM DESCRIPTION Press the ENTER AUTO button on the control panel or the ENTER AUTO button on the Auto remote control to automatically adjust frequency phase and position Press the lt P buttons to adjust the A D sampling number Press the lt P buttons to adjust the A D sampling clock Horizontal Position Press the lt P buttons to adjust the display position right or left
45. t the Power LED is green If you have replaced the lamp recently try resetting the lamp connections momo Replace the lamp module 6 Putthe old lamp back in the projector and have the projector serviced Problem The lamp goes off 1 Power surges can cause the lamp to turn off Re plug power cord When the READY LED is on press the power button Replace the lamp module Put the old lamp back in the projector and have the projector serviced 41 DLP Projector User s Manual Remote Control Problems Problem The projector does not respond to the remote control 1 c Direct the remote control towards remote sensor on the projector Ensure the path between remote and sensor is not obstructed Turn off any fluorescent lights in the room Check the battery polarity Replace the batteries Turn off other Infrared enabled devices in the vicinity Have the remote control serviced Having the Projector Serviced If you are unable to solve the problem you should have the projector serviced Pack the projector in the original carton Include a description of the problem and a checklist of the steps you took when trying to fix the problem The information may be useful to service personnel For servicing return the projector to the place you purchased it 42 DLP Projector User s Manual HDMIQ amp A Q What is the difference between a Standard HDMI cable and a High Speed HDMI cab
Download Pdf Manuals
Related Search