Beergun Manual - Blichmann Engineering
Contents
1. an adjustable angle BrewMometer a glass level gauge with clean out ports and snap in dip tube The BoilerMaker is clearly in a class of its own For more information about our complete lineup of brewing products please go to our web site www BlichmannEngineering com BeerGun Owners Manual V5 Blichmann Engineering LLC 20062. for filling Our preferred method is to start with a well scrubbed bottle a faucet mounted bottle blaster makes this easy Then run through a wash cycle neck down in your dishwasher WITHOUT any detergent or rinse aid Be sure to use heated dry cycle Detergents and rinse aids will destroy the head retention and impart a soapy flavor to the beer While the bottles are washing tear an adequate amount of 3 X 3 aluminum foil squares and soak them in a no rinse sanitizer After the heated dry cycle your bottles will be quite sterile Remove them and immediately cover with a foil square sealing it tightly on the lip of the bottle then store the bottles in a case or container for later use If you have notably hard water and no softener this might not be a suitable method for you due to calcium deposits so we would recommend soaking the bottles in a picnic cooler of no rinse sanitizer in lieu of the dishwasher About an hour before you are going to fill the bottles place them in the refrigerator with your beer to let them come to the same temperature as the beer Bottle Filling You noticed how easy the BeerGun is to assemble and sanitize not you ll experience how intuitive and fast it is to use We find it handy to have a sanitized heavy beer pitcher to hold the filler upright between bottles Arrange your workspace in an efficient manner with everything in an easy to reach location Prior to installing the ball lock
3. slide the stainless beer trigger onto the tube Do not install the trigger onto the beer tube just yet Proceed to step 5 first 5 Install the small black silicone valve seat onto the U shaped stainless clip as shown in Fig 7 Then install the clip onto the groove on the end of the CO2 tube Caution The rubber valve seat can be torn and permanently damaged if incorrectly removed from the valve clip Please carefully pull it straight off the valve clip not at an angle or twisting motion 6 With the filler on a flat hard surface place the clip end of the trigger over the groove in the beer tube oriented as shown in Fig 8 Pressing on BOTH sides of the tube to prevent bending push it into the groove until it clicks into place To remove it invert the filler and again push down on both sides of the tube until it snaps out of the trigger clip 7 Slip the 10ft length of 3 16 ID beer hose onto the end of the beer tube 3 8 about 3 8 as shown in Fig 9 Installing it deeper than this makes removal more difficult Using a shorter length of hose or a hose with a larger ID will increase the likelihood of foaming Connect the other end of the hose to the beer out on the keg using a liquid ball lock connector included in the accessory kit 8 Connect the CO2 hose to the brass valve as shown in Fig 10 The fittings shown are included with the optional accessory kit Fig 10 9 Connect the beer hose and CO
4. www BlichmannEngineering com Beer COz clips come off tube in use The clips are made of a heat treated stainless steel but can still be permanently deformed If this has happened very gently bend them back together with a pliers a little bit at a time until it snaps on firmly by hand To prevent this do not pull unnecessarily hard on the trigger and do not force the clips aggressively onto the grooves Warranty The BeerGun is warranted to be free of defects in materials and workmanship for a period of lyr from the date of purchase proof of purchase required Specifically EXCLUDED from this warranty are normal wear and tear damage from abuse and misuse thread galling or breakage from over tightening Blichmann Engineering is not responsible for incidental or consequential damages or injury arising from use or misuse of this product Replacement parts are available through your Retailer TM BLICHMANN engineering The original Blichmann champions Dana Nicole and Julie New BowerMaxen ew Brew like a champion with a BoilerMaker brew pot They feature an exclusive stepped bottom and an optional patent pending button louver false bottom see graphic to right Also available is an optional boil filter with guard see graphic to left Custom built with the home brewer in mind these beautiful pots ar constructed from heavy 18 gauge stainless steel and loaded with standard accessories including
5. 2 hose to your regulator as shown in Fig 11 That s it After a few uses it will take less than a minute to assemble the filler Use of the BeerGun The BeerGun is used mainly for filling beer bottles and growlers from previously kegged and carbonated beer It can however be used to fill bottles from a bottling bucket or even be used to fill wine bottles provided there is a source of CO available In this case little pressure is available to push the beer through the hose so a shorter length of hose is recommended to increase flow rate Since the beer in this application is not carbonated foaming is not an issue Warning The use of pressurized CO equipment can create hazardous pressures DO NOT AT ANY TIME exceed 15 PSI on the filler Ensure that your regulator is in good working order and the pressure is initially set below 5 PSI and the outlet valve of the regulator is turned off prior to connecting it to the BeerGun Key factors to reduce foaming e Chill bottles to the same temperature as the beer e Always use a 10ft length of 3 16 ID hose to reduce the pressure of the beer as it flows to the filler e Use the minimum dispensing pressure possible to fill the bottle at an acceptable rate of the dispensing pressure is a good starting point e QUICKLY open and close the beer valve trigger to prevent throttling of the beer Bottle Preparation There are numerous methods to satisfactorily sanitize bottles
6. BLICHMANN erm OTIN ELE BeerGun Operation Assembly amp Maintenance Manual Congratulations on your purchase and thank you for selecting the BeerGun bottle filler from Blichmann Engineering We are confident that it will provide you years of service and many bottles of outstanding beer This manual will familiarize you with the assembly and use of the BeerGun bottle filler xxk PLEASE READ THOROUGHLY PRIOR TO USE FOR IMPORTANT SAFETY INFORMATION IMPORTANT Caution Sections labeled Caution can lead to equipment damage or unsatisfactory performance of the equipment Please read these sections thoroughly If you have any questions contact your retailer or Blichmann Engineering www BlichmannEngineering com before use Warning Sections labeled Warning can lead to serious injury or death if not followed Please read these thoroughly and understand them completely before use If you do not understand them or have any questions contact your retailer or Blichmann Engineering www BlichmannEngineering com before use Assembly amp Installation Prior to Assembly Disassembly Ensure you have all the parts included in Fig 1 Please contact your Retailer if any parts are missing The optional accessory kit is shown in Fig 2 and includes everything you need to get your filler connected to a standard ball lock keg The hose clamp provided can be easily installed and tightened with a wire cutter If you d
7. connectors on the keg posts spray the post with a bit of no rinse sanitizer After letting it sit for a couple minutes install the connectors Set the regulator to of the normal dispensing pressure and open the pop off valve on the keg to equalize the pressure to this new setting Clear the COz line of air by depressing the brass push valve for a few seconds Purge the beer line by pulling the beer trigger quickly open until the beer flows through it and all foam is out of the line Important Always QUICKLY OPEN AND CLOSE the beer valve to reduce foaming Take a bottle and remove the foil cap Insert the stem of the filler all the way to the bottom of the bottle as shown in Fig 12 Depress the CO2 valve for 3 5 seconds to purge the bottle of air Note it is normal to get a small leakage of CO2 at the gap where the beer tube passes through the hole in the brass elbow This small clearance is needed to ensure smooth operation of the beer tube Holding the bottle at an angle with the stem of the filler in the bottom corner of the bottle Fig 13 QUICKLY pull the beer trigger and flood the tip of the filler as quickly as possible to reduce foaming When the tip has been immersed in beer you can return the bottle to an upright position Fill the bottle until any foam has spilled out of the neck and is completely full of beer and QUICKLY release the trigger to stop the flow of beer Remove the stem and the volume displaced by the stem
8. ny change in pressure or increase in temperature will cause this excess CO to come out of solution causing excessive foaming and gas bubbles in the beer line Therefore when carbonating your beer DO NOT speed gas it by applying more than the dispensing pressure There is no way to control the amount of CO2 entering the beer using this method Apply the correct amount of pressure typically 8 12 PSI and let it sit for a week or so to carbonate If you do want to speed it along you can roll shake the keg but DO NOT exceed the recommended pressure for your desired carbonation level Most Homebrewing books contain carbonation charts If you believe you have over carbonated your beer you will need to vent the excess gas over several days by removing the CO and pulling the pressure relief valve on the top of the keg Do this several times per day until you have vented the excess carbonation Mechanical Beer tube is sticking the hole in the brass elbow is sized for a tight running fit to minimize CO leakage during bottle purge and is checked at the factory for satisfactory movement Check to see that the CO tube is installed square to the brass elbow If this does not eliminate the sticking check to see if the beer tube is bent by rolling it on a very flat surface such as a machined table saw or granite counter A slight bend can be carefully removed If this does not resolve the problem contact Blichmann Engineering through our web page
9. o not already have one you will need to add a T or a Y shown in Fig 11 on page 4 into your gas line with a shut off valve to connect the gas hose to the BeerGun and also to the keg The T Y adapter is not included in the kit but is available through your Retailer eran erty The BeerGun has been shipped pre assembled so you can visualize how it goes together But it does need to be cleaned and sanitized prior to the first use The assembly steps follow but disassembly is simply the reverse of these steps Caution Do not disassemble until you have read the assembly procedure The filler may be permanently damaged if not disassembled correctly Do not use excessive force on any of the parts during assembly or disassembly or they may be permanently damaged The sheet metal valve clip and the beer trigger are made of heat treated stainless steel but can still be deformed and the tube grooves can be permanently damaged or bent It is also not necessary to firmly tighten the flare nut onto the elbow a snug fit is all that is needed Do NOT use any cleaner or sanitizer containing chlorine such as bleach Over time this will pit and erode stainless steel It will also damage the brass parts of the filler Any other non chlorine sanitizer is acceptable to use lodophor or StarSan both work very well and do not require rinsing In any case a few minute soak is all that is recommended to prevent any damage to
10. the brass fittings Extended soaking can lead to galvanic corrosion of the filler parts Prior to assembly completely disassemble the filler and wash with a mild detergent The included tube brush makes it easy to clean the interior of the 2 tubes Rinse all parts well and soak in your preferred non chlorine no rinse sanitizer including all the hoses and keg connectors Assembly Procedure 1 Thread the brass push valve onto the brass elbow and orient it as shown in Fig 3 Note that there is an arrow cast into the valve showing the direction of flow it should face toward the elbow It is not necessary to use thread tape at this joint 2 Install the 3 8 diameter stainless CO2 tube onto the brass elbow using the flare nut as shown in Fig 4 Tighten the nut loosely at this point It will be fully tightened in the next step 3 Slide the smaller diameter 1 4 beer tube inside the CO2 tube and through the hole in the brass elbow as shown in Fig 5 If it does not move in and out smoothly check for a bend in the tube see troubleshooting section Tighten the nut snugly with a wrench but do not over tighten Check to see that the CO2 tube is not on at an angle and be sure that the beer tube moves freely If it does not move freely ensure that the CO tube is on straight not causing the beer tube to bind If this does not resolve the trouble refer to the troubleshooting section 4 Slide the spring onto the CO2 tube and then
11. will form an ideal and consistent fill level For bottles larger than 220z and growlers the stem may not reach to the bottom of the bottle Keep the bottle at an angle letting the beer run down the side of the bottle until the tip of the filler is immersed then proceed as follows Place the tip of the filler into the head space as shown in Fig 14 and give it a quick shot of CO to displace any air that has been drawn back into the bottle Fig 14 Cap and move to the next bottle With practice it takes about 20 30 sec to fill and cap a 12o0z bottle If you have minimal foaming and wish to dispense at a faster rate increase the CO pressure If foaming is excessive reduce the pressure Trouble shooting Excessive foaming QUICKLY open and close the beer trigger Ensure bottles are at the same temperature as the beer aow Ensure all hoses clamps and fittings on the beer side are tight and not letting air into the system Reduce the dispensing pressure until foaming reaches an acceptable level Highly carbonated or high protein beers like wheat oats etc are difficult to fill so patience is needed f Ensure that 10 ft of 3 16 ID hose is used to reduce the beer pressure on the way to the filler moa If you are still experiencing foaming we have found that nearly always it is a result of over carbonated beer Over carbonated beer contains more CO in solution than is stable at the given pressure and temperature A
Download Pdf Manuals
Related Search