Home

FXS H.323 Gateway User Manual (2FXS, 2AFXS

1. Step 8 Step 9 Step 10 Step 11 FXS Gateway Overview Protocol should now be on the list of installed network components Click the Properties button The TCP IP Properties windows consist of several tabs Choose the IP Address tab Select Specify an IP Address and enter 10 1 1 1 in the IP Address location where xxx is a number between 2 and 254 used by the FXS Gateway to identify each computer and the default Subnet Mask 255 0 0 0 Note than no two computers on the same LAN can have the same IP address Click on the DNS Configuration tab and select Enable DNS Then click the Add button Click on the Gateway tab and enter the High Performance FXS Gateway default gateway value 10 1 1 254 in the new gateway field then click Add Button Click OK Restart your PC to complete the TCP IP installation 1 9 Power Up Your FXS Gateway At this point you should have connected the console port the LAN Port the WAN port and the power port to the appropriate devices or lines Plug the power adapter into a wall outlet The Power LED should be on The Status LED will come on after the system tests are complete The WAN LED and one of the LAN LEDs come on immediately after the Status LED come on if connections have been made to the LAN and WAN ports FXS Gateway Overview 1 9 FXS Gateway Overview Part Il Web Configuration with FXS Gateway This par
2. The following table describes this screen Table 17 1 Line Status Information LABEL DESCRIPTION Line 1 4 This field Display line status is Ready or Busy Line Status Screen 17 1 FXS Gateway Overview Chapter 18 Version and Information Screen This chapter explains the Version and Information Screen 18 1 Version and Information Overview The web configurator provides Version and Information screen to allow you to see FXS Gateway Version Information 18 2 Version and Information Screen Click Version and Information in the navigation panel to open the Version and Information screen Yersion and Information Boot Rom Faw o Application Rom fefs2032 DSP Application rs30zce3 140 ooo DSP Kernel fesozki40 ooo DSP Test Code pssi ooo Figure 18 1 Version and Information The following table describes this screen Table 18 1 Version and Information DSP Test Code This field refers to the DSP Test Code Version Version and Information Screen 18 1 FXS Gateway Overview Chapter 19 Password Screen This Chapter explains how to change the FXS Gateway password 19 1 Password Configuration Overview The Password screen allows you to configure the administrator password 19 2 Password Configuration Screen Click Password in the navigation panel to open the Password Configuration screen Use the Password Configuration to set root and administrator password for the FXS Gateway It is highly
3. You can use FTP TFTP to perform configuration backup restore and firmware upgrade for the FXS Gateway from a remote location security o Password protection for system management o VLAN 1 3 Default Settings The following are the settings of the defualt profile Oo Login root Oo Password Null default 1 3 1 IP Parameters o IP Address 10 1 1 3 Oo Subnet mask 255 0 0 0 o Default gateway 10 1 1 254 1 3 2 Telnet and Web Login Password O Login root FXS Gateway Overview 1 2 FXS Gateway Overview Oo Password Null default 14 Front Panels 2AFXS VoIP Gateway LAN WAN 10 LINKO 10 LINKO 1000 ACT 1000 ACT READY STATUS TEL2 TEL1 POWER Figure 1 11 2AFXS Front Panel 4AFXS T olP Gatewa LAN WAN y 10 e LIMA O 10 Y LINK O 1006 ACT 1000 ACT READY STATUS TEL4 TEL3 TEL2 TEL1 POWER Figure 1 2 4AFXS Front Panel 1 5 Back Panel Ports DG i2V CoM TELA TEL2 Figure 1 3 2AFXS Gateway Back Panel Ports DC 12V COM TELA TEL2 TEL3 TELA WAN LAM 1 51 9600 2 N 1 N 10 100BASE T Figure 1 4 4AFXS Gateway Back Panel Ports 1 6 Hardware Specifications These are the hardware details of the 2AFXS 4AFXS 1 6 1 2AFXS LEDs The following table describes the LED functions Table 1 1 2AFXS LEDs Functions LEDs Functions Indicator Active Description Status Switch to another device such as PC to another device such as PC While plugging on the Ethernet cable it must light on and the flash if some
4. Enter the new IP address in the Location or Address field Press Enter Initial Configuration 3 2 FXS Gateway Overview 3 4 DHCP mode Step 1 Configuration the FXS Gateway IP address for DHCP Mode Click Network Interface on the navigation panel In the Network Interface screen enable the DHCP function if you are using the cable modem or DHCP server and click the OK button Network Interface IP Address 192 168 fa 92 subnet Mask 255 255 Jo Jo Default routing gateway DNS primary fe ps no o DNS secondary fe sf 2 SNTP enable disable SNIP Server Address he ps fies 2 GMT a IP Sharing C enable disable IP Sharing Server Address pio fies fics OK Figure 3 4 Network Interface Step 2 Click Commit Data on the navigation panel In the Commit Configuration Data screen click the Commit button In the Commit Configuration Data screen to Display Commit to Flash OK When the Commit Data Ok Step 3 Click Reboot Data on the navigation panel In the Reboot FXS Gateway screen click the Reboot button It will take 40 seconds to reboot Step 4 Close the current browser windows and launch your web browser again Enter the new IP address in the Location or Address field Press Enter Initial Configuration 3 3 3 0 Step 1 Step 2 Step 3 Step 4 FXS Gateway Overview PPPoE mode ATU R ADSL Modem dAFXS i VoIP Gateway FXS Gateway Config
5. FXS interface To connect analog phone sets or trunk line of PABX 12V DC Port DC Power supply FXS Gateway Overview 1 6 FXS Gateway Overview 1 6 4 Back Panel Connections This section outlines how to connect your FXS Gateway to the LAN and the WAN In the case of connecting a Cable Modem you must connect the coaxial cable from your cable service to the threaded coaxial cable connect on the back of the cable modem Step 1 Connecting the Console Port For the initial configuration of your FXS Gateway you need to use terminal emulator software on a workstation and connect it to the FXS Gateway the console port Connect the 9 pin end of the console cable to the console port of the FXS Gateway and the other end to a serial port COM1 COM2 or other COM port of your workstation You can use an extension RS 232 cable if the enclosed one is too short After the initial setup you can modify the configuration remotely through telnet connections Step 2 Connect the FXS Gateway to the WAN port Connect the WAN port silver on the FXS Gateway to the Ethernet port on the cable modem using the cable that came with your cable modem The Ethernet port on the cable modem is sometimes labeled PC or Workstation Step 3 Connecting the PC to the LAN If you have more than one PC you must use an external hub Connect the 10 100M LAN Port gold on the FXS Gateway to a port on the hub using a straight through Ethernet cable If
6. Figure 92 VO TC CONSUMO oiquin 9 1 Figure 0 4 Phone Contratas 10 1 Picure t Support Conti Urano 11 1 Prsute 12 OD Pn Book css AT ET erg te 12 1 Pre re WS I BUS Mii aa aa 13 1 Figure 14 1 Specd Dialing List sii its 14 1 Erstire Sl PPPOE Device C Ont UFO 15 1 Prsurert6 1 TOS C On Gi Sur Al Oi tc E T 16 1 Proure 17 1 Line Status ntormalON ii i n 17 1 Figure 18 1 Version and Information ersen a a 18 1 Fieure 19 1 Password Conti UTN 19 1 List of Figure VI FXS H 32 W r_ Manual Eistire 20 ROM Omi Sat Oi iia 20 1 g SN gers E 9s Gl orc armen ae er eae eee A C Mane re Sere a ter tree 21 1 Figure 22 1 Commit Configuration Data ooonncnnnccccncnnnonncnnnnnnnnnnnnnannnnnnnnnnnonananononss 22 1 Pretire 2 5 1 REDOOLEXS Gale way sois 23 1 Figure 24 1 Connection Description ccccocoooonnnnnnnnnnnonnnnnoncnnnnnnnnnnnnnnnnnnnnnnnonnnaninnnnss 24 1 Figure 24 2 Connect On DesCripr1On ini 24 2 Eure 24 5 Connect tacos 24 2 Erotire 24 4 Com Properties 24 3 Figure 24 3 Mita SCI 24 4 E LOS mM Scree A a A A 24 4 Figure 24 7 Change password Srita a 24 5 Eteure 24 8 QUitCOmmend ista ita dee adoos 24 14 Figure 24 9 Debug Commend Listas tenso 24 15 Figure 24 10 Reboot Commend Litunia 24 16 Fitur 2A 1 Blasi Commend dd stad leasdusuauavcaes 24 16 Feur 2 12 Commit Commend Listin 24 17 Figure 24 15 adr Commend Listrier 24 18 Fiore 24 14 Time Commend Lidia a ias 24 19 Figure 24 19 Pins Commend Asta ls 24 19 Figure 24 16 Phone Book Comm
7. 1 Gateway and O Terminal Default Gateway IP address 0 0 0 0 255 255 255 255 Prefix number 1 Phone number 2 Phone number 3 Phone number 4 Phone number IP side registered H323 ID String representing display information for reporting to the called party Gatekeeper auto discovery gkdis On 1 Off 0 RTP port number 1024 65532 RAS TTL time 0 3600 second Gatekeeper finding port 1024 65535 Gatekeeper RAS port 1024 65535 h225 q931 range H 225 RAS port 1024 65535 H 225 call signal port 1024 65535 Dynamically allocated port range 1500 65535 respto Max waiting time for Ist response to a new call 1 200 connto Max waiting time for call establishment after receiving 1st response of a new call 1 20000 Example h323 gk 210 59 163 171 linel 70 line2 71 line3 72 line4 73 alias Figure 24 20 H323 Stack Commend List Parameter Usages print print current h323 related settings mode alternatives for gatekeeper or peer to peer mode O gatekeeper mode peer to peer mode If users select gatekeeper mode a extra gatekeeper is needed when FXS Gateway is in operation usr config h323 mode peer to peer mode gk to assign gatekeeper s IP address when FXS Gateway is in gatekeeper mode algk assign second gatekeeper s IP address as redundancy Command List 24 26 dfgw gwtype prefix linel line2 Command with FXS Gateway default gateway is ap
8. A 2 1 23 Losin and Wel COME CTE DA AAA 2 1 De WV CLC AT REUS NI 2 2 29 SAVING YOU COnN GUTI AA AAA 2 3 20 Navicaine the Web CON TSUTO IO ried ince alain 2 4 CHAPTER 3 INTIAL CONEIGUR ATION sonata aida de Je uote disc ae aed 3 1 Sd Initial Configuration OVCIVVWS A dai 3 1 32 General CON SUTTON A AAA dt 3 1 IN CARACAS e Tod 3 1 SAPI T MOS SAA AAA 3 3 OE O CC a 3 4 OL SHARE CONT OUTONO AE EEEIEE NEET A eee 3 5 CHAPIER4 MARINGA VOIPRCAL G comen e A ads 4 1 4 1 Configure the gateway into the Peer to Peer mode ooooncccnnnnconnnnnnnnnnnanncnnnnnnonanonnnnnnnos 4 4 2 Configure the gateway into the GK routed mode ooooooonnccnninnoonnnnnnnnonanonnnnnononannnnnnnnnns 4 3 Table of Connect HI FXS H 32 W r Manual CHAPTERS UPGRADE ROM VERSION cota E 5 1 5 1 Before you start doWwnlOadINgZ ooooonnnnnnnnnnononanananananonnnnncnnononnnnnnn nono nn nonnnannnncnnnnnnos 5 1 I Updo Application VISTO ios 5 1 CHAPTER O NETWORK INTERFACE SCREEN sist a 6 1 Ol Network Interface OVEIVIE Wilde 6 1 0 2 NeW IEJ ACES TET pasceisti a e Na 6 1 CHAPTER 7 H323 INFORMATION SCREEN ies T E i aed cohen EA Wie ate en 7 1 Tek TAILS E ONE Ura AICC E E icicadod 7 1 LL TAILS CO Uran ON CO AAA AA AAA 7 1 CHAPTER 8 SYSTEM CONFIGURATION SCREEN ciie eed en e ane eaa N T Aa EARR 8 1 OLS VSICM Conn curation OVINA ds S 1 SZ OVSICHE CONTIGUA ON ICON A A AS S 1 CHAPTER 9 VOICE SETTING SCREEN tracto iteten titi 9 1 Ob Voice Con ouralo OVErVIC Wai ai aan 9 1 D2
9. Click OK to save your changes back to the FXS Gateway volatile memory Note User s could insert any information in IP Address Destination and DNS Primary PPPoE Configuration Screen 15 2 FXS Gateway Overview Chapter 16 IP Packet ToS Screen This Chapter covers IP Packet ToS Type of Service Differentiated Service configuration 16 1 TOS Configuration Overview The web configurator provides TOS Configuration screen 16 2 TOS Configuration Screen Click IP Packet ToS in the navigation panel and open the TOS Configuration Screen TOS Configuration signalling Packet DSCP Code fo Media Packet DSCP Code fo OK Figure 16 1 TOS Configuration The following table describes this screen Table 16 1 TOS Configuration LABEL DESCRIPTION Signaling Packet set the Signaling Packet DSCP code value the value of is from 0 to 63 DSCP Code e g 7 Media Packet DSCP Set the Media Packet DSCP Code the value of is from 0 to 63 e g 0 Code IP Packet ToS Screen 16 1 FXS Gateway Overview Chapter 17 Line Status Screen This chapter explains the Line Status Information Screen 17 1 Line Status Information Overview The web configurator provides Line Status Information screen 17 2 Line Status Screen Click Line Status in the navigation panel to open the Line Status Information screen Line Status Information Linel Ra ooo Line2 Ra ooo Line3 Rey Lined ey Figure 17 1 Line Status Information
10. IP address and 2 4 phone sets bring you to Voice over IP world 1 2 Features of The FXS Gateway FXS Gateway Features ITU T H 323 v3 compliance Ethernet 2FXS One 10Base T Ethernet port 2AFXS 4AFXS Two 10 100 Base T Ethernet ports Configuration interface RS 232 TELNET and HTTP web management Automatic Gatekeeper Discovery Dimensions 2FXS 165 W x 25 H x 100mm D 2AFXS 4AFXS 222 W x 34 H x 143mm D Transmit Voice and T 38 fax simultaneously Support T 38 ECM function Error Correction in high speed fax Mode Provides call progress tone E 164 Common Dial Plan DTMF Dialing Inband Outband DTMF TFTP FTP software upgrade Remote configuration reset LED indication for system status Support Static IP DHCP and PPPoE To define the dialplan Set the ring back tone from the IP or local FXS Gateway Overview 1 1 FXS Gateway Overview O FAX redundancy support o RAS and Signal port exchangeable O GK id support and GK auto discovery Audio feature Codec G 711 a u law G 723 1 6 3kbps G 729A G729B G 729AB VAD Voice Activity Detection CNG Comfort Noise Generate G 168 165 compliant adaptive echo cancellation Dynamic Jitter Buffer Bad Frame Interpolation Voice DTME Gain Settings Generate Caller ID DTMF or FSK Provide In band or Out band DTMF generation detection Provide Progress tone system Monitoring O System status Link Ready Status TEL Power Remote Firmware Upgrade
11. IPaddress name Alias e164 phonenumber drop digit insert prefixstring pbook delete index pbook modify index IP IPaddress name Alias e164 phonenumber drop digit insert prefixstring Command List 24 19 Command with FXS Gateway print Display phonebook data add Add an record to phonebook search Search an record in phonebook delete Delete an record from phonebook insert Insert an record to phonebook in specified position modify Modify an exist record Note If parameter end_record is omited only record start_record will be disp lay If both parameters end_record and start_record are omited all records will be display Range of IP address setting 0 0 0 0 255 255 255 255 Range of index setting value 1 100 drop 0 Disable 1 Enable Example pbook print 1 10 pbook print 1 pbook print pbook add name Test IP 210 59 163 202 e164 1001 pbook insert 3 name Test IP 210 59 163 202 e164 1001 drop 1 insert 1234 pbook delete 3 pbook search IP 192 168 4 99 pbook modify 3 name Test IP 210 59 163 202 e164 1001 usr config Figure 24 16 Phone Book Commend List Parameter Usages print print out current contents of Phone Book Users can also add index number from 1 to 100 to the parameter to show specific phone number Note lt index number gt means the sequence number in phone book If users do request a specific index number in phone book FXS Gateway will g
12. NOU COM ESULAOR S VO AS as 9 1 CHAPTER LO PHONE PATTERN SCREEN a oe atea odos 10 1 10 1 Phone Configuration OVETVIEW iii A A 10 1 TO2 F hone CORA SUTTON IS COMA AA AA AA ad 10 1 CHAPTER Pl SUPPORT FUNCTION SCREEN 23555 ela e dle 11 1 Add Support COR CUFA ON OVervieW a dead 11 1 TTD SUP PONE COn oura ON ICC 11 1 CHAPTER T2 PHONE BOOK SCREEN cua a aca ta 12 1 12 PON BOOK OVCIVIE Wa daa 12 1 LZ POC BOOK CONS A A a dos 12 1 CHAPTER I HOT LINES CREEN curu p at siii iio iii 13 1 ISA BUCEO OVCT VI CW A AAA AA AA A ES 13 1 TZ DUCAU TOT sc T E cell del ontbeld aaa aeadan eee oma aeee 13 1 CHAPTER 14 SPEED DIAL SCREEN veroisia estados a doo 14 TAT SPCCA DIME VI di 14 1 14 2 Speed IMAMIS CMS ias 14 1 CHAPTER 15 PPPOE CONFIGURATION SCREEN quisas 15 1 LDA PPPoE Device Configur tion OvervieW a 15 1 15 2 PPPoE Device Configuration Screen cccecccccccccsnssecetccsenssesesccsenseeetcccuaaseeesccssaaseeers 15 1 CHAPTER LOIPEACKET TOS SCREEN ii e o tela 16 1 TOMOS CONPMGULAMONOVEIVICW ss iia A A 16 1 10 2 FOS COR UTILON CTC in 16 1 CHAPTER T7 CINESI ATUS SCREE Nireduaseph rare a a a 17 1 AL Line Status Imormati on OVEIVICW ais a A ai 17 1 Table of Connect IV FXS H 32 W r Manual TTD ARE SIOTUS S CVCCM isa E A sina E dan A Sine E 17 1 CHAPTER 18 VERSION AND INFORMATION SCREEN ccccccceeeeeeeeseeseessessnacceeeeeeeeeeeeeeeeeeeeeeeeas 18 1 18 1 Version and Information OVervVIeW ooooonnncnnnnnnononnnannnnnnnnnnnnnnnnnnnnnnnnnnonnnnnnnnnnn
13. commit then reboot process user can start to do other configurations via HTTPD Application Version 200 supports PPPoE function for user to set up the login ID and password to connect to Internet Please refer to Chapter 24 4 5 for how to set up PPPoE 24 3 3 Application Mode Configuration It is including Basic mode such as Gatekeeper and Peer to Peer and Advanced mode such as Hotline mode and IP Sharing mode It will be detailed in the next Chapter 24 3 4 Saving Your Configuration Save the change of configurations for FXS Gateway and apply the new configurations by rebooting the device Step 1 Confirm the changed configurations input commit and press enter to save it Step 2 Input reboot then press enter to restart FXS Gateway p p p y Command List 24 5 Command with FXS Gateway Step 3 After around 40 seconds FXS Gateway will take effect in new configurations These commands save all system configuration into nonvolatile memory Nonvolatile memory refers to the FXS Gateway storage that remains even if the FXS Gateway power is turned of Run Time memory is lost when the FXS Gateway power is turned off You must use the command to save any configuration that you make otherwise the FXS Gateway will return to its default setting when it is restarted Do not turn off your FXS Gateway or remove the FXS Gateway While saving your configuration 24 4 Application modes This Chapter will introd
14. data is being TX RX FXS Gateway Overview 1 3 FXS Gateway Overview LEDs Functions Indicator Active Description Status or e ice tomes E On he OM LAN is comecei Link ACT Link ACT Green MN VS ES While plugging on the Ethernet cable it must light on and the flash if some data is being TX RX OFF Teer ate coment 100M i i off The 10M WAN is connected On The 100M WAN is connected a o Green Slow The FXS Gateway 1s in normal mode O Fast Blinking The FXS Gateway is in downloading A arae Status Status Green oo FXS Gateway is in Peer to Peer On i FXS Gateway has successfully registered to Gatekeeper when it is in Gatekeeper mode Blinking The FXS Gateway is not registered to Gatekeeper when it is in Gatekeeper mode The FXS Gateway is in downloading mode TEL 1 2 On The Telephone is Off Hook A Telephone is On Hook Power Power Green The Power adapter is connected to the Gateway Off The system is off or not receiving power Table 1 2 LEDs Functions 1 6 2 4AFXS LEDs LEDs Functions Indicator Active Description Status FXS Gateway Overview 1 4 FXS Gateway Overview LEDs Functions Indicator Active Description 7 LAN lt i CS Switch to another device such as PC to another device such as PC Link ACT Link ACT Green Blinking While plugging on the Ethernet cable it must light on and the flash if some data me being TX RX OFF Phe hone atcoesed wv
15. delete Delete a record from speedDial table SW SpeedDial function enable 1 disable 0 print Display speedDial table Note 1 Use as speedDial trigger 2 One digit only for briefNumber and maxmum 20 digits for mappingNumber 3 No reboot is needed for this feature commit neened 4 The speedDial feature may conflict with UserDefinedPrefix feature when using the same trigger as Therefore before the feature is taking effective it should check whether the UseDefinedSwitch is ON or OFF UserDefinedPref1x is or not to prevent duplicate definition and system conflict Example sdial add 0 00998222000991 9 00998222000992 sdial modify 2 00998222000999 sdial delete 0 1 2 Sdial sw 1 usr config Figure 24 31 Speed Dial Commend List Parameter Note Command List 24 39 Command with FXS Gateway speed dial digit is only from 0 1 9 must dial as trigger so be careful of another command usr config sysconf prefixdiab Please do not use it together Command List 24 40
16. for each codec 20 40 60ms means to send a voice packet per 20 40 60 milliseconds The smaller the packet size the shorter the delay time If network is in good condition smaller sending packet size is recommended In this parameter 20 40 60ms is applicable to G 711u a law and G 729 codec while 30 60ms is applicable to G723 1 codec priority codec priority while negotiating with other h323 device This parameter determines the listed sequence in h 245 TCS message The codec listed in left side has the highest priority when both parties determining final codec User can also select the particular codec without others usr config voice priority g723 only select this codec usr config voice priority g723 g729 g711u g711a select four codecs and g723 is the first choice volume There are three adjustable value voice volume stands for volume which can be heard from FXS Gateway side input gain stands for volume which the opposite party hears dtmf volume stands for DIMF volume level which sends to its own Linel or Line2 Note level of volume is too high or too low may be result in bad performance while connecting to each other nscng silence suppression and comfort noise generation setting 1 ON 0 OFF It is applicable to G723 codec only An example is demonstrated below usr config voice nscng g723 1 mindelay the minimum jitter buffer size Default value 90 ms maxdelay the minimum jitter b
17. is dynamic IP Address while user applies for dial up connection way The LAN IP Address of User s PC can be set as DHCP client in order to gain a valid one 3 Another IP Address for Gateway must be set as an fixed one in order for that IP Sharing device pass forwarding the relevant information from WAN to LAN Besides a valid IP Address meets the IP Sharing device LAN site is the element 4 FXS Gateway must enable the IP Sharing function for the fixed dynamic WAN IP Address Please be noted With Dynamic WAN IP Address a valid Gatekeeper for FXS Gateway to get register on is a must In other word it is not workable in Peer to Peer mode while dynamic WAN IP Address 5 IP Sharing device must have a function to do IP Port mapping Some is named as DMZ some is named as virtual server whatever The VoIP messages from WAN have to completely pass forward to the LAN It 1s said 1f the FXS Gateway 1s assigned a virtual fixed IP Address such as 192 168 1 5 IP Sharing device must forward the VoIP message to 192 168 1 5 Initial Configuration 3 5 Step 1 Step 2 Step 3 Step 4 Step 5 FXS Gateway Overview Configuration the FXS Gateway IP address for IP Sharing Mode Click Network Interface on the navigation panel In the Network Interface screen enter the IP address Subnet mask and the default gateway in the network table Please follow up your IP Sharing device Enable the IP sharing function and put the static IP address
18. network time usr config time Current time is WED SEP 17 12 36 49 2003 Command List 24 18 Command with FXS Gateway usr config Figure 24 14 Time Commend List 24 7 8 ping Use ping to test whether a specific IP 1s reachable or not For example if 192 168 1 2 is not existing while 210 63 15 32 exists Users will have the following results usr config ping 192 168 1 2 no answer from 192 168 1 2 usr config ping192 168 1 254 PING 192 168 1 254 56 data bytes 64 bytes from 192 168 1 254 icmp_seq 0 time 5 ms 64 bytes from 192 168 1 254 icmp_seq 1 time 0 ms 64 bytes from 192 168 1 254 icmp_seq 2 time 0 ms 64 bytes from 192 168 1 254 icmp_seq 3 time 0 ms 192 168 1 254 PING Statistics 4 packets transmitted 4 packets received 0 packet loss round trIP ms min avg max 0 1 5 210 63 15 32 1s alive usr config Figure 24 15 Ping Commend List 24 7 9 pbook Phone Book function allows users to define their own numbers which mapping to real IP address It is effective only in peer to peer mode When adding a record to Phone Book users do not have to reboot the machine and the record will be effective immediately Phonebook information and configuration Usage pbook print start_record end_record pbook add IP IPaddress name Alias e164 phonenumber drop digit insert pr efixstring pbook search IP IPaddress name Alias e164 phonenumber pbook insert index IP
19. party also 24 32 Command with FXS Gateway supports fastStart tunnel to switch ON OFF 1 ON 0 OFF H 245 tunneling function If the function is ON FXS Gateway will send H 245 Call Control messages via H 225 s Call Signal messages link The function is effective only when both side support h245 tunnel h245fs If the function is ON FXS Gateway will send H 245 messages after FastStart Note it is not recommended to change the value in this command only if users do know well the application This might cause incompatibility with other devices 24 7 19 tos IP Packet ToS Type of Service Differentiated Service configuration usr config tos IP Packet ToS type of Service Differentiated Service configuration Usage tos rtptype dscp tos sigtype dscp tos print rtpreliab mode tos print Example tos rtptype 7 sigtype O usr config Figure 24 26 ToS Commend List Parameter Usages rtptype the packages of voice sigtype the package of call signal Note The value of rtptype and sigtype is from 0 to 63 It s working if it supported by your network Command List 24 33 Command with FXS Gateway 24 7 20 phone FXS Gateway progress tone is configurable Default tone value is set according to U S tone specification Users may adjust the values according to their own country s tone specification or users defined tone specification usr config phone Phone ringing r
20. to Flash OK When the Commit Data Ok Step 6 Click Reboot Data on the navigation panel In the Reboot FXS Gateway screen click the Reboot button It will take 40 seconds to reboot 4 2 Configure the gateway into the GK routed mode Step 1 Configuration the FXS Gateway H323 Configuration Click H323 Configuration on the navigation panel In the H323 Configuration screen select GK routed Mode function Step 2 To change the GK information from your service provider Gatekeeper IP 2nd Gatekeeper IP Gateway Type Registered Prefix Line Number Line 2 Number e g Gatekeeper IP 192 168 4 71 2nd Gatekeeper IP 192 168 4 71 Gateway Type Gateway Registered Prefix 0 Linel Number 000 Line2 Number 001 and click the OK button Making a VoIP Call Screen 4 3 FXS Gateway Overview H323 Configuration Mode GE routed Peer to Peer Gatekeeper IP Address 192 168 4 71 2nd Gatekeeper IP 192 168 471 Gateway Type Gateway Terminal Registered Prefix lo Linel Number 000 Line Number 001 Registered Alias rxs o06102 Display information 2FXS5 Multicast C enable disable RTP Port 16384 Time To Live TTL 60 Figure 4 5 Configure the GK info Step 3 Click Commit Data on the navigation panel In the Commit Configuration Data screen click the Commit button In the Commit Configuration Data screen to Display Commit to Flash OK When the Commit Data Ok Step 4 Cl
21. 150 Optimized bo Factor Jitter 3 C enable disable ox Figure 9 1 Voice Configuration The following table describes this screen Table 9 1 Voice Configuration LABEL DESCRIPTION Set priority preference of installed codes G 723 G 711A G711U G729 G 729A G 729B G729AB Frame Size Set Specify sending packet size G 723 G 711A G 711U G 729 G 729A G 729B G 729AB G723 Silence Select enable disable for G723 Silence Suppression function Suppression Volume Set voice input DTMF functions specify the following levels Echo Canceller Setting enable disable of echo canceller Voice Setting Screen 9 1 FXS Gateway Overview LABEL DESCRIPTION Jitter Buffer Min Setting of jitter buffer min delay Delay Setting of jitter buffer max delay Optimized Factor Setting Optimized Factor Jitter Jitter Click OK to save your changes back to the FXS Gateway volatile memory Note Well the application before you change voice parameters because this might cause incompatibility Voice Setting Screen 9 2 FXS Gateway Overview Chapter 10 Phone Pattern Screen This Chapter covers FXS Gateway progress tone is configurable Default tone value is set according to U S tone specification Users may adjust the values according to their own country s tone specification or users defined tone specification 10 1 Phone Configuration Overview The web configurator provides Phone Configurat
22. 7 5 commit Save changes after configuring FXS Gateway usr config commit Command List 24 16 Command with FXS Gateway This may take a few seconds please wait Commit to flash memory ok usr config Figure 24 12 Commit Commend List Note Users shall use commit to save modified value or they will not be activated after system reboot 24 7 6 ifaddr Configure and display FXS Gateway network information usr config ifaddr LAN information and configuration Usage ifaddr print dhcp used l sntp mode server cmcenter Paddress ifaddr 1p ipaddress mask subnetmask gate defaultgateway print Display LAN information and configuration ip Specify IP address mask Set Internet subnet mask gate Specify default gateway IP address dhcp Set DHCP client service flag On Off http Set HTTP port number dns Set DNS server IP address sntp Set SNTP server mode and specify IP address timezone Set local timezone ipsharing Specify usage of an IP sharing device and specify IP address ipchange Change IP address when using IP sharing function cmcenter Specify IP address of management center Range of IP address setting 0 0 0 0 255 255 255 255 DHCP client setting value On 1 Off 0 If DHCP set to On Obtain a set of Internet configuration from DHCP server assgined SNTP mode O no update l specify server IP 2 broadcast mode Example ifaddr ip 210 59 163 202 mas
23. Core Image DSP Test Image different options from the drop down list box OK lick OK to save your change back to the FXS Gateway volatile memory ROM Upgrade Screen 20 1 FXS Gateway Overview Chapter 21 Flash Clean Screen This Chapter covers save change and clean all the user defined value in factory default mode 21 1 Flash Clean Overview The web configurator provides Flash Clean screen 21 2 Flash Clean Screen Click Flash Clean in the navigation panel and open the Flash Clean Screen Flash Clean FAS Gateway will be reset to factory default values CLEAN Figure 21 1 Flash Clean The following table describes this screen Table 21 1 Flash Clean LABEL DESCRIPTION Save Changes after configuring FXS Gateway Note Itis only executed by user whose login name is root All configurations in command ifaddr pppoe will be kept ROM Upgrade Screen 21 1 FXS Gateway Overview Chapter 22 Commit Data Screen This Chapter covers save change after configuring FXS Gateway 22 1 Commit Configuration Data Overview The web configurator provides Commit Configuration Data screen 22 2 Commit Configuration Data Screen Click Commit Data in the navigation panel and open the Commit Configuration Data Screen Commit Configuration Data lit will take few seconds CONDUIT Figure 22 1 Commit Configuration Data The following table describes this screen Table 22 1 Reboot FXS Gat
24. FXS H 323 Gateway User Manual Version 2 03A September 2003 FXS H 32 W r_Man Notice Copyright 2002 Co Ltd All intellectual property rights in this publication are owned by Co Ltd and are protected by Republic of China copyright laws other applicable copyright laws and international treaty provisions Co Ltd retains all rights not expressly granted No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Co Ltd No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by Co Ltd or its agents Co Ltd reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes Co Ltd may make improvements or changes in the product s and or the program s described in this documentation at any time If there is any software on removable media described in this publication it is furnished under a license agreement included with the product as a separate document If you are unable to locate a copy please contact Co Ltd and a copy will be provided to you Unless otherwise indicated Co Ltd registered trademarks are registered in the Republic of China and other territories For further information contact us or your local distributor or reseller Note FXS H 32 W RELEASE NOTE Date
25. HyperTerminal lojx File Edit View Call Transfer Help i Connection Description 2 x ee New Connection Enter a name and choose an icon for the connection Name Icon Disconnected Anto detect Auto detect SCROLL CAPS NUM Capture Print ech Figure 24 1 Connection Description Step 2 Define a name such as voip for this new connection Command List 24 1 Command with FXS Gateway Sf S15 sea a 5 BETS 8 777 448 0 Eli Figure 24 2 Connection Description Step 3 After pressing OK button the next window appear and then choose COM1 2 Port which you are going to use 83 a x D Dip AAA AO E sA A tt 6557 hE pera 8865 hk iE oz ESE m Figure 24 3 Connect To Step 4 Configure the COM Port Properties as following Bits per second 9600 Flow control None Press OK button and then start to configure FXS Gateway Command List 24 2 Command with FXS Gateway COM1 Properties El ES Port Settings Bits per second ETM Data bits le Parity None a Stop bits Flow control None Restore Defaults Figure 24 4 Com Properties 24 2 Power Up Your FXS Gateway At this point you should have connected the console port the LAN Port the WAN port and the power port to the appropriate devices or lines Plug the power adapter into a wall outlet The Power LED should be on The Status LED will come on after the system te
26. If destination device is FXO device such as 6FXO Gateway it is important of that the configuration 1s in Line to Line mode or Hotline mode Please refer to FXO user manual for more information about two modes a Line to Line bureau hotline Host_Line Remote_IP Remote_Line For example bureau hotline l 210 59 1 1 6 6 means the Sixth port of FXO Gateway caller will hear dial tone then dial to where PBX allowed to b Hotline bureau hotline Host_Line Remote_IP Remote_Line_Number For example bureau hotline 1 210 59 1 1 305 805 means the extension number user define to dial out 24 4 4 Behind IP Sharing Mode The function is for user whose network environment is behind IP Sharing device It is said FXS Gateway is connected to the IP Sharing device An example such as ADSL network is in the following ATU R ADSL Modem FXS Gateway MA FA Lio BAH VHF Gateway E Ss a 1 FP a A E mi i mi mE 1 The WAN IP Address obtained from ADSL has two kinds of methods One is fixed IP Address while user applies for one or more fixed IP Addresses Another is dynamic IP Address while user applies for dial up connection way Command List 24 8 Command with FXS Gateway 2 The LAN IP Address of User s PC can be set as DHCP client in order to gain an valid one 8 Anther IP Address for FXS Gateway must be set as an fixed one in order for that IP Sharing device pass forwarding the relevant information from WAN
27. Introduction 2 1 FXS Gateway Overview 2 4 Welcome Screen This is the web configuration welcome screen Click a link on the navigation panel to go to the corresponding screen a Network Interface H323 Information Welcome to 4EXS Web Confieuration Server System Config es Please chick the Hems in feft france Voice Setting Phone Pattern Support Functions Phone Hook Hot Lines speed Dial PPPok Co uration IP Packet ToS Line Status Version and Information Password hd Figure 2 2 FXS Gateway web configuration welcome screen The following table describes the screen Table 2 1 Navigation Panel Links LABEL DESCRIPTION Network Interface This link takes you to a screen where you can configure the FXS Gateway Network Interface Information H323 Information This link takes you to a screen where you can setup up H323 Information System Config This link takes you to a screen where you can set up System Configuration Voice Setting This link takes you to a screen where you can set up Voice Configuration Phone Pattern This link takes you to a screen where you can set up Phone Pattern Configuration Web Configuration with FXS Introduction 2 2 FXS Gateway Overview LABEL DESCRIPTION Support Functions This link takes you to a screen where you can set up Support Functions Configuration Phone Book This link takes you to a screen where you can set up Phone Book Information Hot Li
28. Lnum or PortNo bureau print print Display Bureau line information and configuration hotline Set Hot line information Note Hotline feature should be used together with sysconf service 2 HotLine service h323 mode 1 peer to peer mode Example bureau hotline 1 192 168 4 69 628 2 192 168 4 200 999 usr config Figure 24 28 Bureau Commend List Parameter Usages print Display current Hotline table hotline Define Linel and Line2 s Hotline table respectively The table is included Line number destination IP Address and destination Port or Number For example define Line hotline table and destination IP Address 1s 200 168 4 69 1 Destination 1s a FXS device 628 is its Linel number usr config bureau hotline 1 200 168 4 69 628 User picks up the Line1 and then hears the ringback tone generated from destination Of course 628 are ringing simultaneously 2 Destination 1s a FXO device Port 3 is the one connected to PSTN Line usr config bureau hotline 1 200 168 4 69 82265699 Command List 24 36 Command with FXS Gateway User picks up the Linel and then hears the ringback tone generated from destination Simultaneously 82265699 numbers is the destination which is dialed from Port 3 Above FXO example is subject to the FXO configurations such as 2nd dial ON or OFF 24 7 22 rom ROM file information and firmware upgrade function usr config rom ROM files updating commands Usa
29. Port number which FXS Gateway uses it to discover a gatekeeper Default value is 1718 To set default gatekeeper RAS port number Default value 1719 is well known port for RAS communication To set the ras port 1024 65535 To set the call signal port 1024 65535 To allocate port range 1500 65535 FXS Gateway may use it Maximum response time out Maximum connection time out 24 27 Command with FXS Gateway 24 7 14 pt RTP payload type configuration and information usr config pt RTP payload type configuration and information Usage pt print Display the RTP payload type information rfc2833 Configurate the DIMF RFC2833 payload type dtmf Configurate the DTMF payload type fax Configurate the FAX payload type faxbypass Configurate the FAX ByPass payload type modembypass Configurate the MODEM ByPass payload type redundancy Configurate the Redundancy payload type modemrelay Configurate the MODEM Relay payload type Example pt rft2833 96 fax 101 usr config Figure 24 21 RTP Commend List 24 7 15 sysinto This command could show up the line is busy or not usr config sysinfo System information Not registered Not registered Not registered Not registered Command List 24 28 Command with FXS Gateway Figure 24 22 System Information Commend List 24 7 16 prefix This command is for make rules for drop or insert prefix digits usr config prefix Prefix drop insert information
30. When in Peer To Peer mode FXS Gateway will send SETUP message directly to the destination IP address once the dial is finished Users have 2 methods of dial One is IP Address dialing and the other is PhoneBook dial which we will describe later When using IP address as 66 99 destination phone number press as in IP address expression and press when dial is Command List 24 6 Command with FXS Gateway finished When using PhoneBook users can dial predefined phone number and press as end of dial Or users can use SpeedDial button which is mapping to user defined PhoneBook Buttonl to PhoneBookIndex1 Button to PhoneBookIndex2 etc To configure Peer To Peer Mode in FXS Gateway follow the steps below Step 1 Set Peer To Peer Mode using h323 command usr config h323 mode 1 Memo mode l is for Peer To Peer non gk mode while mode 0 is for GK mode Step 2 Configure PhoneBook using pbook command Users can refer to chapter 24 7 9 pbook command for more information Memo The command is to add a record onto PhoneBook After the command completed you can type pbook print to see if the input record is correct When adding a record to PhoneBook users do not have to reboot the machine and the record will be effective immediately For phonebook configuration please refer to Chapter 24 7 9 Note l The e164 number defined in Pbook command will be completely carried to de
31. aal 100M LANis connected WAN ink to the HUB Router directly Link ACT Link ACT Green Blinking While plugging on the Ethernet cable it must light on and the flash if some data is being TX RX OFF ets comes 100M yan es off The 10M WAN is connected On The 100M WAN is connected a a Green Slow The FXS Gateway 1s in normal mode O Fast Blinking The FXS Gateway is in downloading A eraa Status Status Green oo FXS Gateway is in Peer to Peer On ie FXS Gateway has successfully registered to Gatekeeper when it is in Gatekeeper mode Blinking The FXS Gateway is not registered to Gatekeeper when it is in Gatekeeper mode The FXS Gateway is in downloading mode TEL 1 4 On The Telephone is Off Hook off The Telephone is On Hook Power Power Green On The Power adapter is connected to the Gateway The system is off or not receiving power FXS Gateway Overview 1 5 FXS Gateway Overview 1 6 3 Back Panel Port Ethernet Port Ethernet port is for connecting FXS Gateway to network transmit rate supports 10 100 Base T 1 34 3676 Hook OPA m 1h a Urge neath IA as N E Dn MC a INE en oe WY EL EL HC a Ethernet connector LAN COM Port RS232 console port DB 9pin male connector Note use straightforward cable to connect to your computer PINOUTS Pin Name Dir Description 3 TXD Transmit Data 5 GND System Ground TEL Port RJ 11 connector
32. aling List New Record Brief Mapping Number Add Data Delete Data Figure 14 1 Speed Dialing List The following table describes this screen Table 14 1 Speed Dialing List Speed Dialing Select enable disable of Speed Dialing function m D mul Speed Dial Screen 14 4 FXS Gateway Overview pee Add Data Add a record to Speed Dialing Delete Data Delete a record to Speed Dialing Speed Dial Screen 14 2 FXS Gateway Overview Chapter 15 PPPoE Configuration Screen This Chapter covers Display PPPoE related information 15 1 PPPoE Device Configuration Overview The web configurator provides PPPoE Device Configuration screen 15 2 PPPoE Device Configuration Screen Click PPPoE Configuration in the navigation panel and open the PPoE Device Configuration Screen PPPoE Device Configuration Device C On 0f UserName pppoe ss ssts S Password pe IP Address _ Destination DNS primary DOO oe AN HR ET N TAE On le Off OK Figure 15 1 PPPoE Device Configuration The following table describes this screen Table 15 1 PPPoE Device Configuration LABEL DESCRIPTION Device Select on off of PPPoE device function UserName Enter the User Name of PPPoE Login ID PPPoE Configuration Screen 15 1 FXS Gateway Overview LABEL DESCRIPTION SUCCESS Reboot After Remote Select on off of reboot after remoter host disconnection function Host Disconnection
33. all hear the 2 dial tone generated by FXS Gateway To retrieve the call back just press the FLASH again Call Transfer press FLASH then transferring number For example A call B B transfer to C A make call to B B press FLASH A and B hear 2 dial tone B presses the C s number C ringing and A hear the ringback tone B hang up its call A and C make call Command List 24 10 Command with FXS Gateway Call Forward gt Activate 147 gt Deactivate 258 gt Busy Forward Forward No gt Noresponse Answer Forward No 1 gt Unconditional Forward No 2 It is important to send an activate deactivate call forward message before setting up the forward number This function is only available under GK mode and the GK supports H 450 Call Forward function There are three conditions for user to set a forwarding number Step 1 Busy Forward while line is engaged or phone set is off hook Step 2 No response Answer while no one answer the call Step 3 Unconditional forward it unconditionally 24 5 How to upgrade Before you start downloading 4 TFTP server program is available to obtain from technical support website Please create one directory for TFTP server program on one local PC and then execute it Put the file which prepared to upgrade in the same directory Please confirm Host PC which is installed as TFTP FTP server and device is in available netwo
34. amage the unit and possibly render it unusable Table 24 1 Commands with FXS Gateway A tne oe voice Voice information manipulation Command List 24 13 Command with FXS Gateway E Packet ToS Type of Service values sdial SpeedDial information configuration 24 7 System Commands Overview 24 7 1 quit Type quit will quit the FXS Gateway configuration mode And turn back to login prompt Welcome to Terminal Configuration Mode Please enter your configuration item usr config Figure 24 8 Quit Commend List Note It is recommended that type the quit command before you leave the console If so FXS Gateway will ask password again when next user connects to console port 24 7 2 debug Open debug message will show up specific information while Gateway 1s in operation After executing the debug command it should execute command debug open as well One example is demonstrated below usr config debug Debug message information and configuration Usage debug add typel type2 open close status Command List 24 14 Command with FXS Gateway status Display the enabled debug flags add Add debug flag delete Remove specified debug flag open Start to show debug messages close Stop showing debug messages Example debug add h323 h323vp debug open usr config Figure 24 9 Debug Commend List In this example user open debug flags including h323 vp h323vp usr conf
35. and configuration Usage prefix add prefix number drop number insert digits prefix delete index prefix modify index prefix number drop number insert number prefix print Prefix drop insert information prefix The prefix of dialed number drop Drop prefix Enable 1 Disable 0 insert Insert digits Example prefix add prefix 100 drop 1 insert 2000 prefix add prefix 100 drop 1 prefix add prefix 100 drop 0 insert 200 prefix delete 1 prefix modify 1 prefix 100 drop O insert 300 usr config Figure 24 23 Prefix Commend List Parameter Usages add add a rule to drop or insert prefix digits of incoming call prefix add prefix prefix number drop 0 1 insert insert number delete delete a rule to drop or insert prefix digits of incoming call prefix delete prefix prefix number modify modify a rule to drop or insert prefix digits of incoming call prefix modify prefix prefix number drop 0 1 insert insert number prefix set which prefix number to implement prefix rule drop enable or disable drop function If this function is enabled Gateway will drop prefix number on incoming call Insert set which digit to insert on incoming call Command List 24 29 24 7 17 voice Command with FXS Gateway The voice command is associated with the audio setting information There are four voice codecs supported by FXS Gateway usr config voice Voice codec setting informatio
36. ate Modified Contents 1 3 Nov 21 BurtC F RELEASE JONA ee Fo aa Jerry Kao Z REVISION aed ii Jerry Kao 2 Revision There is no ver 1 5 re organize 13 2002 lt n article structure Jerry Kao 5 Revision for ver 200 added h 450 a 7 unction application web pppoe Max Su add userdefine in P2P codec T38 ECM 21 E Filter Ring back tone DNS RAS and Signal port change GK Id GK discovery Version Id FAX redundancy support Sep 18 i user define in DDNS Pt Payload type Chen Jerry Kao Revisied for ver 200 added HTTB web user ar 2002 manual Note r Man FXS H 32 W r Manual Table of Contents TABLE Sis CONTENT ie ide II ISTORLICGORE Sur ippo cados VI STORTA Esso cion VIII ERERACE din IX EXS GATEWAY OVERVIEW sra as 10 CHAPTER JP XS GATEWAY OVERVIEW se ds aid 1 1 Ded ADSACGO TEO OV CV V1 CW A A A A A A a 1 1 L2 Features OF The FXS GOLEWOY ada da tadas 1 1 ES DCSE SCLIN OS A NA AAA 1 2 ARTO F ONO AA 1 3 BD TOOTS DAA fed cidcag tenets EE E E aloe saat anata heats 1 3 LO TI GVAWOTE SPec CANONS ata AAA aca 1 3 1 7 AGQUIONG Install ON REGUITCINCIES ia 1 7 LO LOWer UP YOURE XS COW toas wanes 1 8 WEB CONFIGURATION WITH FXS GATEWAY oom 0 0000 10 CHAPTER 2 WEB CONFIGURATION WITH FXS INTRODUCTION sseseeeececeeeeeeeeeeeeeeeeeeeees 2 1 2 1 Web Configuration with FXS Overview tddi 2 1 LA ACCESSIN The WED CONT Ural oli sasen a T
37. ateway Overview 2 6 Navigating the Web Configurator The web configurator uses one level For example to configure Network Interface click the link on the navigation panel to open the configuration screen a H323 Information evstem Config Voice Setting Phone Pattern support Functions Phone Book Hot Lines speed Dial PPPoE Co uration IP Packet ToS Line Status Version and Information Password El Network Interface 7 Adis oz e fr 2 Subnet Mask ass pss foe Default routing gateway fiz fies a pse HTTP Port 80 DNS primary fe ps fh DNS secondary fe psf 2 SNTP enable C disable SMIE Server Address fies ps fies 2 GMT a IP Sharing C enable disable IP Sharing Server Address pio fo fies iss oK Figure 2 3 Network Interface Screen Web Configuration with FXS Introduction zl 2 4 FXS Gateway Overview Chapter 3 Initial Configuration This Chapter covers the basic configuration needed to set up and use the FXS Gateway Refer to the other part describes about individual fields within screens 3 1 Initial Configuration Overview This chapter describes the procedure for the initial configuration of the FXS Gateway Refer to the relevant chapters in this User s Guide for descriptions of the fields and buttons within individual screens 3 2 General Configuration The FXS Gateway the factory with a default IP address of 10 1 1 3 and a subnet ma
38. be ringing callalive Call Alive function 1 ON 0 OFF The function is used to check if the opposite party is alive when connection is established When CallAlive is activated FXS Gateway will send H 245 RoundTrIPDelay message to other party and wait for response If the other party cannot respond the message in 10 seconds FXS Gateway will regard the opposite party as IDLE state and disconnect the call When CallAlive is deactivated Round TrIPDelay message will not be sent during connection keypad DTMF replay type When value is 0 FXS Gateway will transfer DTMF signal via RTP payload 1 via H 245 UII Alphanumeric 2 via H 245 UII Singal Type and 3 via Q 931 UserInfo Users can adjust the value Command List 24 24 Command with FXS Gateway according to various applications flash Disable sending H 450 call hold and transfer message Enable sending normal flash message callerid support Bell Core callerID function After the first ring at destination site device will send h323ID and line number as callerID to called site localringback Enable the local ring back tone or disable sendIPringback Enable the ring back tone from the IP side or disable prefixsw to switch on off prefix function prefixdisab Disable the defined prefix after press the selected digit 0 1 9 usrdefprefix To define digits as prefix filter To define the dialplan for the users faxrdd Set the value of fax redundanc
39. ck tone bt busy tone dt dial tone This parameter should be accompanied with tone type For example usr config phone print rbt Phone ringback tone paramter Ringback Tone frequency high 480 Ringback Tone frequency low 440 Ringback Tone frequency high level 155 Ringback Tone frequency low level 155 Ringback Tone tonel on 2000 Ringback Tone tonel off 4000 Ringback Tone tone2 on 2000 Ringback Tone tone2 off 4000 Note For tone simulation FXS Gateway adopts dual frequencies as traditional telephone does If users want to have their own call progress tone they can change the value of tones High and Low frequency level cadence can be configured respectively ring to set RING tone value The played tone type when FXS Gateway is receiving a call rbt to set RingBackTone value The played tone type when FXS Gateway receives a Q 931 Alerting message In condition that FXS Gateway 1s the originate side bt to set BusyTone value The played tone type when destination is busy dt to set DialTone value The played tone type when hook off a phone set of workable FXS Command List 24 35 Command with FXS Gateway Gateway flash set the detective flash range in ms for example 300 500 ms 24 7 21 bureau To set Hotline function must be under Peer to Peer mode and switch to hotline mode usr config bureau Bureau line setting information and configuration Usage bureau hotline Port DestIP TE
40. e if password of root account is prepared as vo1p configuration is usr config passwd set root voip Password voip OK Command List 24 4 Command with FXS Gateway usr config Figure 24 7 Change password Screen 24 3 Command Structure with FXS Gateway You can use text command lines for software configuration The rules of the commands are listed next The command keywords are in courier new font 1 The command keywords must be entered exactly as shown that is no abbreviations are allowed 2 Command refers to a command used in the command line interface 24 3 1 Command Structure with FXS Gateway The FXS Gateway uses a two level command structure with the FXS Gateway The commands related to one subsystem are group under a primary command of that subsystem for instance to configure the parameters you must fist enter the usr config subsystem by entering the ifaddr command When you are in a subsystem the system reminds you by including the subsystem name in the command prompt for example usr config 24 3 2 Setup IP Address Use command ifaddr to configure Gateway s IP Address and related information For example usr config ifaddr ip 10 1 1 1 mask 255 2555 255 0 gate 10 1 1 254 Description This is to configure FXS Gateway s IP Address as 10 1 1 1 subnet mask as 255 255 255 0 default router gateway as 10 1 1 254 Note After configured the IP Address and did the
41. e or more characters Predefined choices are in Bold Arial Font Button and field labels link s and screen names in are in Bold Times New Roman font A single keystroke is in Arial font and enclosed in square brackets Enter means the Enter For brevity s sake we will use e g as shorthand for for instance and 1 e for that is or in other words Naming Conventions gt FXS Gateway refers to the FXS Gateway 2AFXS and 4AFXS for 2 Ethernet Port Related Documentation gt gt This user s guide provides hardware connection details and configuration and management instruction for the managements FXS Gateway Please refer to Technical Support or Select Product VoIP Gateway download library for additional support documentation List of Table IX FXS Gateway Overview Part FXS Gateway Overview FXS Gateway Overview Chapter 1 FXS Gateway Overview The chapter introduces the FXS Gateway general feature factory default settings and 1 1 hardware FXS Gateway Overview FXS Gateway which based on ITU T H 323 v3 provides voice and fax over IP networks Its simplified operation and configuration features are the most suitable for residential and SOHO application There are three models for FXS Gateway which are 2FXS 2AFXS and 4AFXS One more added switch hub for A series is the only difference User can choose 2 ports or 4 ports as request in A series Just an
42. eesseeeeees SHS DATE Fe aR o Proce 2 DAE S Front Pane a 1 3 Firme les 4 ARAS Front Lali diia 1 3 Figure 1 4 2FXS Gateway Back Panel PortS ooonnoonn o gate fap ON TE Bs ER Figure 1 5 2AFXS Gateway Back Panel POrts ccccccccccccccccnsseessnessssesessssescnceees 1 3 Figure 1 6 4AFXS Gateway Back Panel Porta nonien E 1 3 Fisure 2 1 LOSA Cr lianas 2 1 Figure 2 2 FXS Gateway web configuration welcome screen ooooooonnccncnnnnnnnnnnnnnnnnss 2 2 Elstre 2 3 NetWork Interface SEL AS 2 4 Pratre3 1 NS Work Mle ACS a cea a eo cca detec ataw dea eee 3 2 Figure 3 2 Commit Configuration Data cccccccsccccccccecceeceeeaeaeeeeesesseeeeeeeeeeeeeees 3 2 Figure 5 5 ReDoot FAS Gale way soceri aE E alive eetinntute new elakivds 3 2 Pioure 5 4 NetWork Miler ace a e a 3 3 Fioure 5 5 PPPOE Device Onl Sur AtiO Ds successes ads 3 4 Figure 3 6 Enable the IP sharing function ooooooooonnnnccnnnncnnnnnnnnnnnnononononananoconnnncnnnnss 3 6 Figure 4 1 H323 Configuration Peer to Peer mode Screen ccccccsesssseeseeeeeees 4 1 Pistre 4 2 Phone DOOR da 4 2 Figure 4 3 Phone Book New RECO a ii 4 2 Fierce 4 4 Phone IB OOK isis 4 3 Fisure4 gt Contisuire th GK Info nia id 4 4 Pieure 3 1 ROM COn CUA ss 5 1 Eisure 2 ROM Pile Upsrado O dd idad 5 2 Pre re gt las Cia 5 2 Figure 6 1 Network Interact tai 6 1 Fiure Tal H1S23 OMG urano a iigetes hares E E O 7 1 Proure 3 1 SystemC Onn CUA ON 8 1
43. end List Parameter Usages print dev open close id pwd reboot Command List print PPPoE status Enable PPPoE Dial up function Open the connection Close the connection Input the User name ID provided by ISP Input the User name password provided by ISP Reboot the PPPoE connection 24 21 Command with FXS Gateway 24 7 11 ddns The dynamic DNS service information and configuration usr config ddns The dynamic DNS service information and configuration Usage ddns print ddns enable 0 1 ddns serve Address hostname Name id ID passwd Password checkIP option checkIPsrv Address delay time force IP print Display Dynamic DNS information and configuration enable 1 Enabled 0 Disable the dynmaic DNS service server Specify DDNS server address hostname Registered domain name 1d Registered account ID passwd Registered account password checkIP 1 Enabled 0 Disable check the host current IP address checkIPsrv1 Specify IP address check server checkIPsrv2 Specify secondary IP address check server delay Setting the service delay time 1 59 minutes or 1 24 horus force Force execute the dynamic DNS service Example ddns print ddns enable 1 ddns server member dyndns org hostname IPphone dyndns org ddns delay 30 m 30 minutes ddns delay 12 h 12 hours ddns force 11 22 33 44 usr config Figure 24 18 DDNS Commend List Parameter Usages enable enable
44. end Lista sresnienaeni a 24 20 Figure 24 17 PPPoE Commend List cccccceccccccssseeseeceeecceeaeeeesseccceeeessaaanseeeeees 24 21 Figure 24 16 DDNS Commend Listin ad AROS 24 22 Figure 24 19 System Information Commend List oooocccncnccccnnnnnncnnnnnnnnnnnnnnnnnnss 24 24 Fig r 24 20 11525 Stack Commend Listar iia 24 26 Hisure 24 2 RTP Commend Lita dad 24 28 Figure 24 22 System Information Commend LliSt oooccccccnncccnnnnnnnnnnnnnnnnnncnnnnnnnnss 24 29 Figure 24 23 Prenk Commend Lituania 24 29 Fiure 24 24 Voce C ommend Li beri e be 24 31 Figure 24 25 Support Commend LlSt ooooonnnnnnnnncnnnnnononnnnnnnnnononanonnnnnnnnnononaninenoss 24 32 Fisure 24 26 Tos Commend llista a 24 33 Figure 24 2 7 Phone Commend Listar ae 24 35 Fieure 24 20 Dureau Commend Listas R 24 36 Figure 24 29 rom Commend Lis sssi a r 24 37 Fig re 24 30 Passwd Commend Listas a iia 24 38 Figure 24 31 Speed Dial Commend Listar 24 39 List of Figure VII FXS H 32 W r Manual List of Table Table 1 1 2FXS LEDs Descriptions ooooonnccconncnonnnconnnconanonnnoss gare MATH a Table t JAP XS LEDS PunctionSnsia ia E a 1 3 Table 3 LEDS Pum ONS sarita noia 1 4 Table 2 1 Navigation Panel Links N s 2 2 Table 1 1523 COnmeuraOMiccp a 6 1 Table 1523 OMNES A LOM tacos 7 1 Tablezs 1 SYStem COnmeuratiOM sisi 8 1 Table 9 gt 1 Voice Conn UPAt ONS setscncescecdadssondetbauscenxai aa 9 1 Table LO 1 Phone Conhearati oikenee reie 10 1 Table El
45. erver Address fies fs fies 2 GMT a IP Sharing C enable disable IP Sharing Server Address pio fies fics OK Figure 6 1 Network Interface The following table describes this screen Table 6 1 H323 Configuration LABEL DESCRIPTION IP Address Enter the IP Address of the FXS Gateway in dotted decimal notation for e g 192 168 4 92 Range of IP Address setting Network Interface Screen 6 1 FXS Gateway Overview LABEL DESCRIPTION 0 0 0 0 255 255 55 255 Subnet Mask Enter the IP Subnet Mask of your FXS Gateway in dotted decimal notation for e g 255 255 0 0 Default Routing Enter the IP Address of the default outgoing gateway of your FXS Gateway Gateway in dotted decimal notation for e g 192 168 1 254 DHCP Select enable disable Dynamic Host Configuration HTTP Port Set FXS Gateway HTTP Port Number e g 80 DNS primary Enter the DNS IP Address in dotted decimal notation for e g 168 95 1 1 DNS Secondary Enter the DNS secondary IP Address in dotted decimal notation for e g 168 95 1 1 SNTP Select enable disable Simple Network Time Protocol SNTP Server Address Set specify a SNTP Server as network time source in dotted decimal notation for e g 168 95 192 12 emt et local time zone according to GMT e g 8 IP Sharing Select enable IP Sharing function when you specify usage of and IP Sharing device IP Sharing Server Enter specify a global fixed IP Address user can add this IP Addre
46. eway LABEL DESCRIPTION Save changes after configuring FXS Gateway Commit Data Screen 22 1 FXS Gateway Overview Chapter 23 Reboot Data Screen This Chapter covers reboot to reload FXS Gateway in new configuration 23 1 Reboot FXS Gateway Overview The web configurator provides Reboot FXS Gateway screen 23 2 Reboot FXS Gateway Screen Click Reboot Data in the navigation panel and open the Reboot FXS Gateway Screen Reboot 4FXS Gateway lt will take 40 seconds to reboot remember to COMMIT data before reboot REBOOT Figure 23 1 Reboot FXS Gateway The following table describes this screen Table 23 1 Reboot FXS Gateway LABEL DESCRIPTION After commit command type reboot to reload FXS Gateway in new configuration The procedure is as below Reboot Data Screen 23 1 Command with FXS Gateway Part III Command with FXS Gateway Command with FXS Gateway Chapter 24 Command List This section introduces the command line interface and lists all of the commands 24 1 Hyper Terminal Setting A terminal emulator is needed when using RS 232 port to configure FXS Gateway There are kinds of terminal emulator software Here we use Microsoft HyperTerminal to depict how to set up terminal emulator Step 1 Execute the Hyper Terminal program and then the following windows will pop up on the screen START gt Program files gt Accessories gt Communication Hyper Terminal qs New Connection
47. for TFTP while 1 stands for FTP ftp if users choose FTP in above item it is necessary to specify pre defined username and password when upgrading files 24 7 23 passwd For security concern users have to input the password before entering configuration mode passwd command is for password setting purpose usr config passwd Password setting information and configuration Usage passwd set Loginname Password passwd clean Note 1 Loginname can be only root or administrator 2 passwd clean will clear all passwd stored in flash please use it with care Example passwd set root Your_Passwd_Setting usr config Figure 24 30 Passwd Commend List Parameter Usages passwd lt login name gt lt password gt Note lt login name gt can be root or administrator only root and administrator have the same authorization except commands that can be excuted by root only 39 s passwd set root rom boot room boot2m and flash clean Command List 24 38 Command with FXS Gateway 24 7 24 sdial SpeedDial information and configuration usr config sdial SpeedDial information and configuration Usage sdial add briefNum mappingNum sdial modify briefNum mappingNum sdial delete briefNum mappingNum sdial sw enable sdial print add Add a record to speedDial table modify Modify a exist record
48. ge rom print app boot dsptest dspcore dspapp s TFTP FTP server IP f filename rom print print app boot boot2m dsptest dspcore dspapp S f method ftp Note show versions of rom files optional update main application code optional update main boot code optional update 2M code optional update DSP testing code optional update DSP kernel code optional update DSP application code optional IP address of TFTP FTP server mandatory file name mandatory download via TFTP FTP TFTP mode 0 FTP mode 1 specify username and password for FTP This command can run select one option in app boot dsptest dspcore and dspapp Example rom method 1 rom ftp vwusr vwusr rom app s 192 168 4 101 f app bin usr config Command List Figure 24 29 rom Commend List Parameter Usages 24 37 Command with FXS Gateway print show versions of all rom files app boot boot2m dsptest dspcore dspapp to update main Application program code Boot code DSP testing code DSP kernel code or DSP application code Most of all the Rom file needed to get upgrade is App or Boot2m Please check the exactly Rom file before doing download procedure S to specify TFTP server s IP address when upgrading ROM files f to specify the target file name which will replace the old one method to decide using TFTP or FTP as file transfer server 0 stands
49. ick Reboot Data on the navigation panel In the Reboot FXS Gateway screen click the Reboot button It will take 40 seconds to reboot Making a VoIP Call Screen 4 4 FXS Gateway Overview Chapter 5 Upgrade ROM Version This Chapter covers the basic how to upgrade FXS Gateway ROM Version 9 1 Before you start downloading TFTP server program is available to obtain from technical support website 2 Please create one directory for TFTP server program on one local PC and then execute it Put the file which prepared to upgrade in the same directory 3 Please confirm Host PC which is installed as TFTP FTP server and device is in available network 4 Remember the current configuration such as pbook h323 5 2 Update Application Version Step 1 Update the FXS Gateway ROM Version Click ROM Upgrade on the navigation panel In the ROM Configuration screen type a Server IP address Target File Name Method Target File Type e g Server IP Address 192 168 4 70 Target File Name 4afxs 203a Method TFTP Target File Type Application image and click the OK button Figure 5 1 ROM Configuration Step 2 In the screen to Display Please issue FLASH CLEAN to consist software version When the ROM Upgrade file ok Upgrade ROM Screen 5 1 FXS Gateway Overview a Support Functions Please issue FLASH CLEAN to consist software version Phone Book Hot Lines Speed Dial PPPoE Co uration IP Packet Tos Line Status Ve
50. ig debug add h323 vp h323vp Parameter Usages status Display the enabled debug flags add Add debug flag h323 h323 related information vp voice related information delete Remove specified debug flag open Start to show debug messages close Stop showing debug messages 24 7 3 reboot After commit command type reboot to reload FXS Gateway in new configuration The procedure 1s as below usr config reboot Attached TCP IP interface to cpm unit 0 Attaching interface lo0 done HTTPD initialized ecminitialize succeed Ras port 1024 Command List 24 15 Command with FXS Gateway CallSignal port 1720 GK mode selected AC4804 0 is ok AC4804 1 is ok successful 2 2 Initialize OSS libraries OK VP v1 42 stack open sucessfully login Figure 24 10 Reboot Commend List 24 7 4 flash Save changes after configuring FXS Gateway usr config flash Flash memory information and configuration Usage flash clean Note This command will clean the configuration stored in the flash and reboot it usr config Figure 24 11 Flash Commend List Parameter Usages clean clean all the user defined value and reboot FXS Gateway in factory default mode Note It is recommended that use flash clean after application firmware id upgraded Warning It is only executed by user whose login name is root All configurations in command ifaddr pppoe will be kept 24
51. in the IP Sharing server address e g 192 168 4 96 and click the OK button subnet Mask 255 255 Jo Jo Default routing gateway fiz fies ft sa HTTP Port s0 DNS primary fe ps 2 DNS secondary fe sf 2 SNTP enable disable SNIP Server Address fies fs fies 2 Figure 3 6 Enable the IP sharing function Click Commit Data on the navigation panel In the Commit Configuration Data screen click the Commit button In the Commit Configuration Data screen to Display Commit to Flash OK When the Commit Data Ok Click Reboot Data on the navigation panel In the Reboot FXS Gateway screen click the Reboot button It will take 40 seconds to reboot Close the current browser windows and launch your web browser again Enter the new IP address in the Location or Address field Press Enter Initial Configuration 3 6 FXS Gateway Overview Chapter 4 Making a VoIP Call This Chapter covers the basic configuration the gateway for making VoIP calls One is the Peer to Peer mode another is GK routed mode The configurations and functions are different Please make sure about the mode you want and follow up the step to configure your gateway 4 1 Configure the gateway into the Peer to Peer mode Step 1 Configuration the FXS Gateway H323 Configuration Click H323 Configuration on the navigation panel In the H323 Configuration screen select Peer to Peer Mode function set line number e g Linel Number 000 Line Numbe
52. ingback tone busy tone dial tone setting and notes Usage phone ring freq ringON ringOFF ringLevel rbt freqHi freqLo freqHiLev freqLoLev TonelON TonelOFF Tone2ON Tone20FF bt freqH1 freqLo freqHiLev freqLoLev TonelON TonelOFF Tone2ON Tone2OFF dt freqH1 freqLo freqHiLev freqLoLev Tonel ON Tonel OFF Tone2ON Tone2OFF flash freqLo freqHi phone print ring rbt bt dt I flash print Display phone ringing tone configuration ring ringing rbt ringback tone bt busy tone dt dialtone flash flash tone ring ringing configuration set rbt ringback tone configuration set bt busy tone configuration set dt dial tone configuration set flash flash configuration set Note ringing frequency 15 100 Unit Hz ringing rng ON OFF 0 8000 Unit ms ringing level 0 94 Unit V tone frequency 0 65535 Unit Hz tone freqLevel 0 65535 Unit mVrms tone Tone ON OFF 0 8000 Unit ms Example Command List 24 34 Command with FXS Gateway phone print rbt phone ring 20 2000 4000 94 phone rbt 480 440 125 105 2000 4000 2000 4000 phone bt 620 480 125 105 500 500 500 500 phone dt 440 350 96 96 8000 0 8000 0 phone flash 400 800 usr config Figure 24 27 Phone Commend List Parameter Usages print print current call progress tone configurations ring ring tone rbt ring ba
53. ion screen 10 2 Phone Configuration Screen Click Phone Pattern in the navigation panel and open the Phone Pattern Screen Phone Configuration p onre EGY Lofy High lew _ Lowde On off ts 480 440 155 155 2000 4000 eats menen rau rn caw E E Ma 620 lago ss ss ist Tone HAGOD Lof Highdlev Ane z 350 155 CC js000 rcpt PRT 350 E 19 x a OK i E E Figure 10 1 Phone Configuration The following table describes this screen Table 10 1 Phone Configuration LABEL DESCRIPTION RingTone Setting the played tone type when FXS Gateway is receiving a call Ring Back Tone Setting the played tone type when FXS Gateway receives a Q 931 Alerting message In condition that FXS Gateway is the originate side Busy Tone Setting the played tone type when destination 1s busy Dial Tone Setting the played tone type when hook off a phone set of workable FXS Gateway Phone Patterm Screen 10 1 FXS Gateway Overview LABEL DESCRIPTION 2nd Dial Tone Set the detective flash range in ms for example 300 500 ms OK Click OK to save your changes back to the FXS Gateway volatile memory Phone Patterm Screen 10 2 FXS Gateway Overview Chapter 11 Support Function Screen This Chapter provides some extra functions that might be needed by users 11 1 Support Configuration Overview The web configurator provides Support Configuration screen 11 2 Support Configuration Screen Click Support F
54. ive each record a automatic sequence number as index add add a new record to phone book When adding a record users have to specify name IP and e164 number to complete the command search search a record in phone book The searching criteria can be name IP or Command List 24 20 Command with FXS Gateway el64 delete delete a specific record pbook delete 3 means delete index 3 record Insert add a new record and force to assign a specific index number for 1t modify modify an existing record When using this command users have to specify the record s index number and then make the change PhoneBook Rules The e164 number defined in phone book will fully carry to destination It is not just a representative number for destination s IP Address In other words user dial this e164 number to reach destination destination will receive the number and find out 1f it is matched to its e164 including Line number in some particular device 24 7 10 pppoe Display PPPoE related information PPPoE device information and configuration Usage pppoe print open close pppoe dev on off id username pwd password print dev open close id pwd reboot Display PPPoE device information Enable 1 or Disable 0 device Open PPPoE connection Disconnect PPPoE connection Connection user name Connection password Reboot after remote host disconnection Figure 24 17 PPPoE Comm
55. k 255 255 255 0 gate 210 59 163 254 Command List 24 17 Command with FXS Gateway ifaddr dhcp 1 ifaddr http 8080 ifaddr dns 1 168 95 1 1 ifaddr sntp 1 210 59 163 254 ifaddr ipsharing 1 210 59 163 254 ifaddr ipchange O usr config Figure 24 13 lfaddr Commend List Parameter Usages print print current IP setting and status 1p assigned IP address for FXS Gateway mask internet subnet mask gate IP default gateway dhcp Dynamic Host Configuration 1 ON 0 OFF sntp Simple Network Time Protocol 1 ON 0 OFF When SNTP function is activated users have to specify a SNTP server as network time source An example is demonstrated below timezone set local time zone according to GMT usr config ifaddr sntp 1 10 1 1 1 While 10 1 1 1 stands for SNTP server s IP address ipsharing To specify a global fixed IP address user can add this IP address in the command usr config ifaddr ipsharing I 210 11 22 33 If the IP address is not a fixed one the dedicated IP address is not necessary in the command However dynamic IP Address is not working in Peer to Peer mode It only supports our Call Manager usr config ifaddr ipsharing 1 cmcenter Specify a management center IP Address We will provide a management center program to do centralized control for all devices 24 7 7 time When SNTP function of FXS Gateway is enabled and SNTP server can be found as well type time command to show current
56. l Support C OnMout AtlOM ewig eri A cea 11 1 Table 1231 Phone BOOK anios 12 1 Table SUBI sii ads 13 1 Table 14 1 Speed Diane Lita e alouteneet ednaaedestes 14 1 able 9 1 PPPOE Device CON CUA a 15 1 Table 10 1TOS Cogn z r O asean a ia 16 1 Table 17 1 Line Status Into MAMMA 17 1 Table Lol Version and Informa 18 1 Table TI MASS Wy OMG iaa a vdd 19 1 Table 20 1 ROM Conte uration raices 20 1 Table 2 1 1 Flisa leai a baine eet 21 1 Table 22 1 Reboot EX S Gatew ay vies ecesecdsc roses saccade actus aceon erase sashaad spate ees 22 1 Table 23 1 Reboot FAS Cte WAV a dad 23 1 Table 24 1 Commands with FXS Gateway oooooooccccccnncnonononocnncnnnnonononannnncnnnnnnnonanos 24 13 List of Table VII FXS H 32 W r Manual Preface Congratulations on your purchase of the FXS Gateway About this User s Manual This user s guide gives hardware specifications and explains web configurator and command line configuration for the FXS Gateway Online Upgrade Please refer to online Technical Support or Select Product VoIP Gateway download library for additional support documentation General Syntax Conventions gt Mouse action sequences are denoted using a comma For example click start Settings Control Panel Network means first you click Start Click or move the mouse pointer over Settings the click or move the mouse pointer over Control Panel and finally click or double click Network Enter means for your to type on
57. mber while registration Gateway Type is Gateway example 60 Display Information Set string representing display information for repertory to the called party Multicast Select Gatekeeper auto Discovery is enable disable RTP Port Set RTP port number example 16384 Time To Live TTL Set RAS TTL Time example 60 Gatekeeper finding Set Gatekeeper finding port e g 1718 port Connection Timeout Set max waiting times for call establishment after receiving 1st response of a new all e g 200 OK Click OK to save your changes back to the FXS Gateway volatile memory Note Linel amp Line2 number must follow the prefix number if device is configured as Gateway type For example if prefix number is 999 the line amp line2 number are 9991 amp 9992 H323 Information Screen 7 2 FXS Gateway Overview Chapter 8 system Configuration Screen This Chapter covers System Information and configuration 8 1 System Configuration Overview The web configurator provides System Configuration screen 8 2 System Configuration Screen Click System conf in the navigation panel and open the System Configuration Screen system Configuration Keypad Type In Band H245 Alpha H245 Sig 0 931 RFC2833 Dial Plan b Inter Digit Time a Call Alive C on OFF Prefix bp Prefix Disable Digit FO oK Figure 8 1 System Configuration The following table describes this screen Table 8 1 System C
58. n and configuration Usage voice send G723 ms G711A ms G711U ms G729 ms G729A ms G729B ms G729AB ms volume voice level input level dtmf level nscng G723 used3 echo used mindelay t1 maxdelay t2 voice print voice priority G723 G711A G711U G729 G729A G729B G729AB print send Display voice codec information and configuration Specify sending packet size G 723 30 60 90 ms G 711A 20 40 60 ms G 711U 20 40 60 ms G 729 20 40 60 ms G 729A 20 40 60 ms G 729B 20 40 60 ms G 729AB 20 40 60 ms priority Priority preference of installed codecs volume nscng echo Command List G 723 G 711A G 711U G 729 G 729A G 729B G 729AB Specify the following levels voice volume 0 63 default 28 input gain 0 38 default 28 dtmf volume 0 31 default 23 No sound compression and CNG G 723 1 only On 1 Off 0 Setting of echo canceller On 1 Off 0 per port basis 24 30 Command with FXS Gateway mindelay Setting of jitter buffer min delay 0 150 default 90 maxdelay Setting of jitter buffer max delay 0 150 default 150 Example voice send g723 60 g71la 60 g711u 60 g729 60 g729b 60 g729ab 60 voice volume voice 20 input 32 dtmf 27 voice echo 1111 usr config Figure 24 24 Voice Commend List Parameter Usages print print current voice information and configurations send to define packet size
59. nction Screen 11 2 FXS Gateway Overview Chapter 12 Phone Book Screen This Chapter covers Phone Book function allows users to define their own numbers which mapping to real IP address It is effective only in peer to peer mode When adding a record to Phone Book users do not have to reboot the machine and the record will be effective immediately 12 1 Phone Book Overview The web configurator allows you to Set up Phone Book that tell the FXS Gateway how to call management traffic when you configuration P2P mode 12 2 Phone Book Screen Click Phone Book in the navigation panel and open the phone Book Screen New Record po r Address i 64 Mo Add Data Delete Data Figure 12 1 Phone Book The following table describes this screen Table 12 1 Phone Book LABEL DESCRIPTION Record List Index The field displays the index number Phone Book Screen 12 1 LABEL DESCRIPTION The field displays the descriptive name IP Address The field displays the IP Address or Domain name e164 The field displays the descriptive e164 number Z Q D A UN G D D lt O lt lt D New Record Set up an Index number Set up a descriptive name IP Address Set up IP Address or Domain Name e164 No Set up e164 telephone number Add Data Add a record to Phone Book Delete Data Delete a record to Phone Book 3 v a D 3 S Note The e164 number defined in phone book will full
60. nes This link takes you to a screen where you can set up Hot Lines configuration Speed Dial This link takes you to a screen where you can set up Speed Dialing List PPPoE Configuration This link takes you to a screen where you can set up PPPoE Device Configuration IP Packet ToS This link takes you to a screen where you can set up TOS Configuration Line Status This link takes you to a screen where you can view Line information about the status of the FXS Gateway Version and This link takes you to a screen where you can view Version and Information Information of the FXS Gateway Password This link takes you to a screen where you can change passwords ROM Upgrade This link takes you to a screen where you can change ROM Upgrade configuration Flash Clean This link takes you to a screen where you can click flash memory information and configuration Commit Data This link takes you to a screen where you can click save your changes to the non volatile memory Reboot System This link takes you to a screen where you can click to reboot FXS Gateway 2 5 Saving Your Configuration Click OK to save your changes back to the FXS Gateway volatile memory The FXS Gateway loses these changes if it 1s turned off or loses power so use the Commit Data link on the navigation panel to the left to save your changes to the non volatile memory when your are done configuring Web Configuration with FXS Introduction 2 3 FXS G
61. nnnnnnnnnnos 18 1 IS 2 VErstO ana IN OTINGHON SCICCH yi A SS 18 1 CHAPTER LD PASSWORD SCREEN suduetmadaidadiranirada tddi tl 19 1 19 1 Password Configuration OVO IV WA A 19 19D POSS WOrd CONN OUTAN ONI CVECE A A toneeages 19 1 CHAPTER ZO ROM UPGRADE SCREEN sorserion aA EAr 20 1 20 1 ROM Configuration OVETVIC Wii AA A A oveeeeuaaes 20 1 20 2 ROM CON Ura Or ICC AA A at 20 1 CAAPTER ZI RUASH CLEAN SCREEN atu loo delos esla EEA 21 1 Dil TAGS CEON OV CIV OW ds 21 1 DEZA NAS CACA ICON lia 21 1 CHAPTER 22 COMMIT DATA SCREEN din ie e 22 1 22 1 Commit Configuration Data OvVervVieW oooooooooonnnnnnnnnnnnnnnnnonnnnnnnnnnnnnnnnnncnnnnnnononaninenss 22 1 222 COMME C ORT SUTA TON IDA ICE and 22 1 CHAPTER 23 REBOOT DATA SCREEN utilities 23 1 23 1 Reboot FXS Gateway OVEIVI Wii A A A ias 23 1 LIZ REDO EXA WA Y ECON aa 23 1 COMMAND WITH FXS GATEWAY eessssccsssssccosssseccosssseecoossssecoossseeceossssecees 2 CHAPTER 2 F OMMAND GIS E a er a Bc 24 1 241 Hyper Terminal Sethin A Waser Ree 24 1 DAL POWER UP VOUr T XAS Gewa y A T T alas 24 3 24 3 Command Structure with FXS Gateway scccccccccccccssssessseececeeccaaesessseceeeeesaaaansssseeees 24 5 DA AD PU CA ON IMSS a 24 6 DAS FLOW AUDIT O A A A sadiuictauoaaareah uta Guiedat adiudauieeess 24 11 246 Commands ERES dais 24 13 24d SYSTCIN Command S OVETVIOW cai ii 24 14 Table of Connect V FXS H 32 W r Manual List of Figures Figure 1 1 2FXS Front Pamell cccccccscssessscssesecsesse
62. onfiguration LABEL DESCRIPTION Keypad Type Select In Band H 245 Alpha H 245 Sig Q931 RFC2833 on DTMF replay type Dial Plan Set Number of digits for dial plan e g 0 Inter Digit Time Set Inter Digits time e g 3 Busy Forward Working in both Gatekeeper mode and Peer to Peer mode some previous version does not support in Peer to Peer mode If the line1 is System Configuration Screen 8 1 FXS Gateway Overview LABEL DESCRIPTION engaged as well as this function is enabled the line2 will be ringing Gateway Service Select specify gateway service type Dial in service or Hot Line service default Dial in service Click OK to save your changes back to the FXS Gateway volatile memory System Configuration Screen 8 2 FXS Gateway Overview Chapter 9 Voice Setting Screen This Chapter covers voice is associated with the audio setting information 9 1 Voice Configuration Overview The web configurator provides Voice Configuration screen 9 2 Voice Configuration Screen Click Voice Setting in the navigation panel and open the Voice Configuration Screen seder yee a ma fa G Emu Law y Ga lt G 729b af G 729ab G 729ah Frame Size 723 30m8 y g729 20ms 67292 2ms 67110 205 7 67110 208 67299 20 20ms y Voice Configuration 6723 Silence Suppression Volume i ma one 23 Echo Canceller enable disable Jitter Buffer Min Delay 90 Max Delay
63. only keep IP Address and MAC Address B 2MB Rom If the version list is older than 113 all configurations will be back to default value including IP Address In other word user has to set IP Address and MAC Address before reboot the device otherwise user cannot access to device any more via Telnet The version 200 and above support to keep every configurations after upgrade Steps 4 1 Find out MAC Address There are 12 digits on label on the back panel of the device or command as usr config ifaddr ifshow find the list information of Ethernet address itis MAC Address usr config setmac set as 2 digits as a group 00 01 as 00 XX XX if confirm press y Steps 4 2 Set IP Address usr config ifaddr ip XXX XXX XXX XXX Mask XXX XXX XXX XXX gate XXX XXX XXX XXX Please refer to Chapter 24 7 6 Steps 4 3 Hardware version confirmation Upgrade 2MB Rom may change the hardware column lf it is not as the same as the one which is found on the label of back panel please command as usr config rom hwver x x Command List 24 12 Command with FXS Gateway Steps 4 4 commit reboot 24 6 Commands with FXS Gateway The following table lists all of the commands that you can use with the FXS Gateway Refer to the following chapters for descriptions of commonly used commands This user s guide describes commands that are helpful for configuring the FXS Gateway Using commands not documented in the user s guide can d
64. plied under Peer to Peer mode User defines a constant default gateway IP address then any number dialed will pass forward to this IP Address gateway type has two kinds gateway and terminal Gateway type device will register as H 323 defined Gateway user has to define prefix in next command Terminal type device will register as H 323 defined Terminal prefix command is not necessary assign Gateway prefix number as well as the registered number on the Gatekeeper assign line 1 number assign line 2 number Note linel amp line2 number must follow the prefix number if device is configured as Gateway type For example if prefix number is 999 then the linel amp line2 s number are 9991 amp 9992 alias display gkdis rtp ttl gkfind gkras h225 q931 range respto connto Command List H 323 ID If in gatekeeper mode this h 323 ID must be different from others who are registering to the same gatekeeper an addition name for user to recognize in called site Switch ON or OFF gatekeeper discovery function 1 ON 0 OFF When it s ON FXS Gateway will multicast for gatekeeper if default gatekeeper is not presented to allocate RTP port range NOT RECOMMENDED This may be used when RTP port range conflicts with Firewall policy to set timer for TTL Time To Live FXS Gateway would send RRQ with keepAlive to gatekeeper periodically according to TTL timer gatekeeper finding port
65. r 001 and click the OK button H323 Configuration 192 168 0 1 2nd Gatekeeper IP on Gateway Type C Gateway Terminal Registered Prefix lo Gatekeeper IP Address Regisiered Alias 2FX5 006 102 Display information 2FXS5 Multicast C enable disable RTP Port 16384 Time To Live TTL 60 Figure 4 1 H323 Configuration Peer to Peer mode Screen Step 2 Configuration the FXS Gateway Phone Book Click Phone Book on the navigation panel In the Phone Book screen enter the Index Name IP address and e164 phone number of the destination and click the Add Data button Making a VolP Call Screen 4 1 FXS Gateway Overview pa pe Address H 64 Mo Add Data Delete Data Figure 4 2 Phone Book Step 3 E g enter the Index 1 Name test1 IP address 192 168 4 72 and e164 No 20 of the destination and click the Add Data button Phone Book Index IP Address E164 Mo En E 168 4 72 Figure 4 3 Phone Book New Record Step 4 On table will display on the first index Making a VoIP Call Screen 4 2 FXS Gateway Overview Phone Book AE AA ee AAA ANNA ENS AI ANS New Record Index 2 IP Address El64 No LO o S E Add Data Delete Data Figure 4 4 Phone Book Step 5 Click Commit Data on the navigation panel In the Commit Configuration Data screen click the Commit button In the Commit Configuration Data screen to Display Commit
66. recommended that you change the default password Null E y py a 7 ssword Configuration Current Password root y New Password o Confirm New Password CHANGE ABORT Figure 19 1 Password Configuration The following table describes this screen Table 19 1 Password LABEL DESCRIPTION Username Select root or administrator different options from the drop down list box Current Password Type the existing system password Null is the default password when New Password Type your new system password Confirm your new system password for confirmation Click CHANGE to save your change back to the FXS Gateway volatile memory ABORT Click ABORT to begin configuring this page afresh Password Screen 19 1 FXS Gateway Overview Chapter 20 ROM Upgrade Screen This Chapter explains how to Update FXS Gateway Version 20 1 ROM Configuration Overview The web configurator provides Update FXS Gateway ROM Version 20 2 ROM Configuration Screen Click ROM Upgrade in the navigation panel and open the ROM Configuration Screen ROM Configuration Server IP Address rf Target File name _ Method TFTP FTP Login TO l Wa oOo Target File Type Application Image OK Figure 20 1 ROM Configuration The following table describes this screen Table 20 1 ROM Configuration Select download Target File Type on 2M Boot Image DSP Application Image DSP
67. rk Remember the current configuration such as pbook h323 Upgrade steps Telnet to remote device Step 1 rom print It will list current version and default download method Please check the Application Rom in particular it is showed version list as well as the most common one you have to upgrade If there is additional Rom noted one Rom which size around 2MB would be provided for user to upgrade all of Roms General speaking App Rom is named including product name and version and size is under 1MB such as 2fxs 115a 2MB Rom is named such as 2m2fxs 115a Please be very careful of the prepared Rom file while upgrading Step 2 Prepare FTP or TFTP server ready A FTP server rom method 1 to choose FTP method and input the FTP login and password by rom ftp 1d password B TFTP server It is default value rom method 0 to choose TFTP method Command List 24 11 Command with FXS Gateway Step 3 Different Rom uses different command A Application Rom usr config rom app s 192 168 1 1 f 2fxs 114 B 2MB Rom usr config rom boot2m s 192 168 1 1 f 2fxs 114 Description app boot2m means the prepared upgrade Rom s means where the TFTP FTP server IP Address 1s f is the Rom file name Step 4 Download complete A Application Rom Command flash clean to clear old configurations It will keep all configurations in ifaddr and pppoe Note old version such as 115a will
68. rsion and Information Password ROM Upgrade Flash Clean Commit Data Reboot System Figure 5 2 ROM File Upgrade ok Step 3 Click Flash Clean on the navigation panel In the Flash Clean screen click the CLEAN button In the Flash Clean screen to Display Flash cleaned Please reboot your system When the Flash Clean Ok TT 11 Flash Clean FAS Gateway will be reset to factory default values CLEAN Figure 5 3 Flash Clean Step 4 Click Reboot Data on the navigation panel In the Reboot FXS Gateway screen click the Reboot button It will take 40 seconds to reboot Step 5 Close the current browser windows and launch your web browser again Enter the IP address in the Location or Address field Press Enter Upgrade ROM Screen 5 2 FXS Gateway Overview Chapter 6 Network Interface Screen This Chapter covers setup Network Interface identification information for FXS Gateway 6 1 Network Interface Overview The web configurator provides Network Interface screen 6 2 Network Interface Screen Click Network Interface in the navigation panel and open the Network Interface Screen Use this screen to setup Network Interface identification information for the FXS Gateway Network Interface 1 Aabess oz fio fr 2 Subnet Mask pss pss foo Default routing gateway fiz fies ft sa HTTP Port s0 DNS primary fe ps no o DNS secondary he ps of 2 SNTP enable disable SNIP S
69. s better to define the port in wider range than limited range 24 4 5 PPPoE Mode ATU R ADSL Modem Command List 24 9 Command with FXS Gateway ID Password JAFXS q ma Wal Gaheway mi ci ee ma mk mh my mm FXS Gateway Press or help to list all commands including PPPoE one Step 1 pppoe dev 1 switch the IP configurations to PPPoE Step 2 pppoe open open the connection Step 3 pppoe 1d input the user ID provided by your ISP Step 4 pppoe pwd input the password provided by your ISP Step 5 pppoe reboot Reboot the device once after disconnection After the configurations are done commit and reboot the device 24 4 6 H 450 Call Hold Transfer and Forward Mode FXS Gateway provides H 450 function including call hold transfer and forward Please be noted that both calling and called site have to support H 450 feature For call forward function it only works under GK mode Of course GK must support H 450 feature such as Call Manager 1 3 To enable H 450 feature it is better for user to prepare a telephone set supported FLASH function on keypad If telephone set does not support FLASH function on keypad user is possible to click the Hook quickly by sending FLASH message The default FLASH value for FXS Gateway is between 100ms to 300 ms It is said the value of Gateway 1s subject to the telephone set Call Hold press FLASH By pressing the FLASH after making a call both site sh
70. serInfo 4 RFC2833 Flash sending 0 Disable 1 Enable Command List 24 23 Command with FXS Gateway callerid Caller ID sending 0 Disable 1 Enable localringback Local generate ring back tone 0 Disable 1 Enable sendIPringback Send ring back tone to IP 0 Disable 1 Enable prefixsw User defined local zone prefix switch ON 1 OFF 0 prefixdisab Local zone prefix disable character one character from 0 9 or NONE key usrdefprefix User defined local zone prefix faxrdd FAX redundancy depth 0 2 eod End of dial switch ON 1 OFF 0 Example sysconf plan 4 callalive O usr config Figure 24 19 System Information Commend List Parameter Usages print print current settings plan digits any positive integer of dial plan This police is effective for calls from PSTN side When FXS Gateway collects the number of pre defined digits it will send those digits out automatically 0 stands for any number which accepts any digit length When dial plan is set to 0 users can end the dial with FF to force FXS Gateway send out messages directly or FXS Gateway will send out the messages automatically in 3 seconds after dialing stops service switch to Hotline mode 0 default 2 hotline bf Working in both Gatekeeper mode and Peer to Peer mode some previous version does not support in Peer to Peer mode If the linel is engaged as well as this function is enabled the line2 will
71. sk of 255 0 0 0 3 3 Static IP address Step 1 Configuration the FXS Gateway IP address Click Network Interface on the navigation panel In the Network Interface screen type a new IP address subnet mask and the default routing gateway e g IP Address 192 168 4 92 Subnet mask 255 255 0 0 Default routing gateway 192 168 1 254 and click the OK button Initial Configuration 3 1 FXS Gateway Overview Network Interface Default routing gateway 192 f s fo jasa HTTP Port 80 DNS primary fe ps 2 DNS secondary fe ps of 2 SNTP enable disable SNIP Server Address fess fies i GMT a IP Sharing C enable disable IP Sharing Server Address pio fies fics OK Figure 3 1 Network Interface Step 2 Click Commit Data on the navigation panel In the Commit Configuration Data screen click the Commit button In the Commit Configuration Data screen to Display Commit to Flash OK When the Commit Data Ok Commit Conficuration Data Ti will take few seconds CONDIT Figure 3 2 Commit Configuration Data Step 3 Click Reboot Data on the navigation panel In the Reboot FXS Gateway screen click the Reboot button It will take 40 seconds to reboot Reboot 4FXS Gateway h will take 40 seconds to reboot remember to COMMIT data before reboot REBOOT Figure 3 3 Reboot FXS Gateway Step 4 Close the current browser windows and launch your web browser again
72. ss in Address dotted decimal notation for e g 210 11 22 33 Click OK to save your changes back to the FXS Gateway volatile memory Network Interface Screen 6 2 FXS Gateway Overview Chapter 7 H323 Information Screen This Chapter covers setup H 323 related parameters 7 1 H823 Configuration Overview The web configurator provides H 323 Configuration screen 7 2 H823 Configuration Screen Click H323 Configuration in the navigation panel and open the H323 Configuration Screen H323 Configuration Mode GE routed Peer to Peer Gatekeeper IP Address jolla 2nd Gatekeeper IP fou2 o SS Gateway Type Gateway Terminal Registered Prefix pT Line Number 000 Line Number 001 Line3 Number 002 Lined Number 003 Registered Alias ferxsooos9 Display Information 4FX5 Multicast C enable disable Figure 7 1 H323 Configuration The following table describes this screen Table 7 1 H323 Configuration LABEL DESCRIPTION Mode Selec Gatekeeper routed mode or Peer to Peer mode Set Gatekeeper IP Address in dotted decimal notation e g 192 168 4 71 2n GateKeeper IP Set redundancy second 2 Gatekeeper IP Address in dotted decimal H323 Information Screen 7 1 FXS Gateway Overview LABEL DESCRIPTION O Mota e 9 192 168 4 71 Gateway Type Select registration Gateway Type is Gateway mode or Terminal mode Registered Prefix Set Prefix nu
73. stination device It is said this number shall be matched the destination device s e164 number if BusyForward function is disable 2 BusyForward function at destination site The function is only for FXS series a Enable sysconf bf 1 then destination device will accept any number even it is not matched to Line number The called device will ring in round robin b Diable sysconf bf 0 then only matched Line number is accepted 24 4 3 Hotline Mode Hotline mode is particularly applied behind Peer to Peer mode it is not workable in Gatekeeper mode The Hotline Mode is applied in limited two peers User just picks up the phone set and then hears ring back tone or dial tone depended on configurations of destination device Usage Switch to Peer to Peer Mode then enable the Hotline Mode Finally create a Hotline table usr config h323 mode 1 usr config sysconf service 2 usr config bureau hotline 1 10 2 2 2 201 usr config bureau hotline 1 10 2 2 2 6 Hotline table usage Select a line for destination IP Address and 1ts Port Extension number 1 FXS Gateway If destination device is FXS device such as FXS Gateway the table should be build Command List 24 7 Command with FXS Gateway like below example bureau hotline Host_Line Remote_IP Remote_Line_Number For example bureau hotline 1 210 59 1 1 111 It is said picking up the Phone Line 1 and then destination gateway will ring 2 FXO Gateway
74. sts are complete The WAN LED and one of the LAN LEDs come on immediately after the Status LED come on if connections have been made to the LAN and WAN ports Initial Screen When you power on your FXS Gateway it performs server internal tests as well as line initialization After the tests the FXS Gateway asks you to enter the Login as shown Attached TCP IP interface to cpm unit 0 Attaching interface lo0 done Please wait while system is initializing SAttached TCP IP interface to cpm unit 0 Attaching interface lo0 done HTTPD initialized cminitialize succeed Ras port 1024 CallSignal port 1720 Command List 24 3 Command with FXS Gateway GK mode selected AC4804 0 is ok AC4804 1 is ok successful 2 2 Initialize OSS libraries OK VP v1 42 stack open sucessfully login Figure 24 5 Initial Screen Entering Login For you first login enter the login root and default password Null As you type the password the screen displays and for each character you type successful 2 2 Initialize OSS libraries OK VP v1 42 stack open sucessfully login root Welcome to Terminal Configuration Mode Please enter your configuration item usr config Figure 24 6 Login Screen Note login root or administrator is the default login name and there is no password needed set Password To set your own password in root login name just input command passwd set root For exampl
75. t tells how to access and navigate the web configurator and perform initial configuration It also describes the Getting Started web configuration when you use the FXS Gateway Overview Chapter 2 Web Configuration with FXS Introduction This Chapter describes how to login into the WEB and navigate through it 2 1 Web Configuration with FXS Overview The embedded web configuration allows you to use a web browser to manage the FXS Gateway 2 2 Accessing the Web Configuration You will need a computer with and Ethernet 10BaseT 100Base TX Network Interface Card NIC Connect to the LAN port in the FXS Use Internet Explorer 5 5 and later or Netscape Navigator 6 and later versions Use the following instructions to login on to the web configuration 2 3 Login and welcome screen Step 1 Start your web browser Step 2 Launch your web browser and enter 10 1 1 3 the default IP address of the FXS Gateway in the Location or Address field Press Enter Step 3 The Password screen now appears Type root in the user name field it may display automatically for you and your password default Null in the password field Step 4 Click OK MARIE 21x gt SA ERE FA ATA mel 194 160 439 AiE AFXS Configuration Web Server ASADO TIE Hoe ele Fee as E ma Figure 2 1 Login Screen Step 5 After a successful login you will see the welcome screen show next Web Configuration with FXS
76. the DDNS function Command List 24 22 Command with FXS Gateway server enter the server address of the DDNS server you use hostname enter the domain name address which you get from the DDNS server 1d key in your 1d passwd key in your password checkIP enable or disable the check current user s IP address checkIPsrv1 enter the IP address of the check server checkIPsrv2 the secondary IP address of the check server delay service delay time force execute the DDNS function all the times Note Support DDNS Server www 3322 0rg www dyndns org 24 7 12 sysconf This command displays system information and configurations usr config sysconf System information and configuration Usage sysconf plan digit idtime digit service type bf digit callalive flag keypad dtmf prefixsw digit faxrdd digit prefixdisab dig1t usrdefprefix digits flash digit callerid digit localringback digit sendIPringback digit eod digit sysconf print print Display system overall information and configuration plan Number of digits for dial plan any positive number idtime Inter Digits time 1 10 sec Service Specify gateway service type 0 Dial in service 2 HotLine service bf BusyForward ON 1 OFF 0 callalive Enable or disable auto disconnection after 10 seconds not receiving packets from remote party keypad Select DTMF type 0 In band 1 H 245 Alphanumeric 2 H 245 SignalType 3 Q 931 U
77. the configuration through telnet connections 1 8 Setting Up the TCP IP Protocol If you are not sure whether the TCP IP Protocol has been installed follow these setups to check and if necessary install TCP IP onto your PCs Step 1 Click the Start button Choose Settings then Control Panel Double click the Network icon Your Network window should appear as follows Step 2 Select the Configuration tab Import For Windows 2000 amp Windows XP Setting you will find that they differs with Windows 98 ME NT slightly See the Following for reference Click the Local Area Connection icon on the lower right hand side of your desktop screen In the Local Area Connection Status windows click the Properties button the your Network windows will appear There is only one tab General in the Network window Step 3 Click whether the TCP IP Protocol has already been installed onto your computer s Ethernet card Note that TCP IP Protocol an be installed for a computer s Dial Up Adapter as well as for the Ethernet cad If yes go to set 7 If no click the Add button Step 4 Double click Protocol in the Select Network Component Type or highlight Protocol then click Add Step 5 Highlight Microsoft under the list of manufactures Step 6 After a new second you will be returned to the Network window The TCP IP FXS Gateway Overview 1 8 Step 7
78. to LAN Besides a valid IP Address which meets the IP Sharing device LAN site is the element 4 FXS Gateway must enable the IP Sharing function for the fixed dynamic WAN IP Address Fixed IP Address usr config ifaddr ipsharing 1 210 11 22 33 Dynamic IP Address usr config ifaddr ipsharing 1 Note With Dynamic WAN IP Address a valid Gatekeeper for FXS Gateway to get register on is a must In other word it is not workable in Peer to Peer mode while dynamic WAN IP Address IP Sharing device must have a function to do IP Port mapping Some is named as DMZ some is named as virtual server whatever The VoIP messages from WAN have to completely pass forward to the LAN It 1s said 1f the FXS Gateway 1s assigned a virtual fixed IP Address such as 192 168 1 5 IP Sharing device must forward the VoIP messages to 192 168 1 5 Important Note For some IP Sharing devices do not support DMZ or virtual server function but allowed user to allocate some particular TCP UDP port range While a complete H 323 communication is established the following ports are possibly to be used TCP port Q 931 H 225 gt 1720 H 245 gt dynamic but range 1025 1029 not in use if Fast Start or Tunnel mode is activated UDP port RAS gt device 1024 Gatekeeper 1719 RTP RTCP gt adjustable default 16384 16384 4 Line Numbers Note The port number allocation is for reference only RTP RTCP port may allocate on unexpected port It i
79. uce the four application modes users often use Particularly the Gatekeeper and Peer to Peer mode are the basic application mode User would like to set as advanced application mode such as Hotline Mode and Behind IP Sharing mode please refer to the basic application mode for more information 24 4 1 Gatekeeper mode User has to prepare a Gatekeeper Program To assign a gatekeeper address for FXS Gateway and define its own registered ID and phone number For detail please refer to Chapter 24 7 13 h323 command Several important H323 parameters are listed below when setting gatekeeper mode _ok owtype prefix line1 and line2 An example is demonstrated below usr config h323 gk 10 2 2 2 prefix 1 linel 11 line2 12 Memo This is to set gatekeeper IP address as 10 2 2 2 prefix as 1 line 1 number as 11 and line 2 number as 12 The gateway type 1s kept as default value as Gateway Type Note For the successful dial plan designed in Gateway Type the linel amp line2 number must follow the prefix number For example if the prefix is set as 002 linel amp line2 can be set as 0021 0022 It is an important dial plan in gatekeeper mode On the other hand if device registered as Terminal Type there is no prefix needed to be defined 24 4 2 Peer to Peer Mode Peer to Peer Mode allows users to call other VoIP devices without using a gatekeeper
80. uffer size Default value 150 ms Command List 24 31 Command with FXS Gateway usr config voice mindelay 90 maxdelay 150 optfacor 7 echo activate each canceler 1 ON 0 OFF Note be sure to know well the application before you change voice parameters because this might cause incompatibility 24 7 18 support This command provides some extra functions that might be needed by users usr config support Special Voice function support manIPulation Usage support t38 enable t38ecm enable fstart enable tunnel enable h245f s enable Support print t38 t38ecm fstart tunnel h245fs Example support support support support support usr config T 38 FAX enabled disabled T 38 FAX ECM enabled disabled Fast start enabled disabled H245 Tunneling enabled disabled H245 message after FastStart support enabled disabled t38 1 t38ecm fstart O tunnel 1 h245fs 1 Figure 24 25 Support Commend List Parameter Usages print t38 t38ecm fstart Command List print current settings in support command to switch ON OFF 1 ON 0 OFF T 38 fax ability When T 38 ability is ON FXS Gateway will automatically defer codec G 723 or G 729a to T 38 when FAX signal is detected Support the error correction in the high speed fax mode to switch ON OFF 1 ON 0 OFF fstartStart function Fast Start function can shorten the connection time 1f the opposite
81. unction in the navigation panel and open the Support Function Screen Support Configuration oK Figure 11 1 Support Configuration The following table describes this screen Table 11 1 Support Configuration LABEL DESCRIPTION 1 38 FAX Select enable disable for T 38 FAX Function When T 38 ability is ON FXS Gateway will automatically defer codec G 723 or G 729a to T 38 when FAX signal is detected T 38 FAX ECM Select enable disable for T 38 FAX ECM Function Support the error correction in the high speed fax mode Fast Start Select enable disable for Fast Start function Fast Start function can shorten the connection time if the opposite party also supports Fast Start H 245 Tunneling Select enable disable for H 245 Tunneling function If the function is ON FXS Gateway will send H 245 Call Control messages via H 225 s Call Signal messages link The function is effective only when both side support h245 tunnel Support Function Screen 11 1 FXS Gateway Overview LABEL DESCRIPTION H 245 Message After Select enable disable for H 245 Message After Fast Start function If the Fast Start function is ON FXS Gateway will send H 245 messages after Fast Start OK Click OK to save your changes back to the FXS Gateway volatile memory Note it is not recommended to change the value in this command only if users do know well the application This might cause incompatibility with other devices Support Fu
82. uration the FXS Gateway IP address for PPPoE Mode Click PPPoE Configuration on the navigation panel In the PPPoE Configuration screen On the Device and put the info of the PPPoE User Name and password e g User 123456 hinet net password 123456 and click the OK button PPPoE Device Configuration IP Address Destination DNS primary Reboot After Remote Host Disconnection C On Off OK Figure 3 5 PPPoE Device Configuration Click Commit Data on the navigation panel In the Commit Configuration Data screen click the Commit button In the Commit Configuration Data screen to Display Commit to Flash OK When the Commit Data Ok Click Reboot Data on the navigation panel In the Reboot FXS Gateway screen click the Reboot button It will take 40 seconds to reboot Close the current browser windows and launch your web browser again Enter the new IP address in the Location or Address field Press Enter Initial Configuration FXS Gateway Overview 3 6 IP Sharing Configuration The function is only for the user who is using the IP Sharing device It is said Gateway is connected to the IP Sharing device The IP Sharing Device must support the DMZ or Virtual server functions An e g such as ADSL network is in the following ATU R ADSL Modem 1 The WAN IP Address obtained from ADSL has two kinds of methods One is fixed IP Address while user applies for one or more fixed IP Addresses Another
83. y Be noted the above three commands prefixsw prefixdisab and usrdefprefix have to work together If user would like to dial 9 to replace 123456789 he can firstly switch on the command usr config sysconf prefixsw 1 secondly to define the prefix digits as 12345678 usr config sysconf usrdefprefix 12345678 While user would like to dial other numbers he can dial a defined digit to disable the function usr config sysconf prefixdisab then dial to the number he wants to dial 24 7 13 h323 This command is to configure H 323 related parameters usr config h323 H 323 stack information and configuration Usage h323 mode gkmode h323 gk IPaddress algk IPaddress gwtype type prefix number alias h3231d display information gkdis used line number rtp port h225 port ttl time gkfind port gkras port q931 port range start num1 end num2 respto t1 connto t2 dfgw IPaddress passwd number gkid 1d h323 print print Display H 323 stack information and configuration mode Configure as Gatekeeper mode or Peer to Peer mode gk Gatekeeper IP address 0 0 0 0 255 255 255 255 algk Second Gatekeeper IP address 0 0 0 0 255 255 255 255 Command List 24 25 gkid gwtype dfgw prefix line 1 line2 line3 line4 alias display gkdis rtp ttl gkfind gkras Command with FXS Gateway Gatekeeper ID Registration Mode
84. y carry to destination It is not just a representative number for destination s IP Address In other words user dial this e164 number to reach destination destination will receive the number and find out 1f it is matched to its e164 including Line number in some particular device Phone Book Screen 12 NO FXS Gateway Overview Chapter 13 Hot Lines Screen This Chapter covers to set Hotline function must be under Peer to Peer mode and switch to hotline mode 13 1 Bureau Overview The web configurator provides Bureau screen 13 2 Bureau Screen Click Hot Line in the navigation panel and open the Bureau Screen 1 192 168 4 69 628 2 192 168 4 69 628 3 192 168 4 69 628 A ee Se eee ae See Mew Record SET Figure 13 1 Bureau The following table describes this screen Table 13 1 Bureau Remote_TEL FXS The field displays the Remote TEL number Port_No FXO Port Set up a port number Destination Address Set up IP Address Hot Line Screen 13 1 FXS Gateway Overview LABEL DESCRIPTION pomen po up Remote Number Set a record to Bureau Hot Line Screen 13 2 FXS Gateway Overview Chapter 14 Speed Dial Screen This Chapter covers Speed Dial information and configuration 14 1 Speed Dialing Overview The web configurator provides Speed Dialing screen 14 2 Speed Dialing Screen Click Speed Dial in the navigation panel and open the Speed Dial List Screen speed Di
85. you only have one PC you can connect the FXS Gateway to the PC directly without a hub For a single PC connect the 10 100M LAN port on the FXS Gateway to the Network Adapter on the PC using a crossover cable red tag Step 4 Connecting the Power Adapter to your FXS Gateway Connect the power adapter to the port labeled POWER on the rear panel FXS Gateway Caution To prevent damage to the FXS Gateway first make sure you have the correct AC power adapter Please see the Appendices for AC power adapter specifications for your region Step 5 Grounding the FXS Gateway If you want to ground the FXS Gateway then connect a grounded wire to the F G Frame Ground of the FXS Gateway 1 7 Additional Installation Requirements In addition to the contents of your package there are other hardware and software requirements you need before you can install and use your FXS Gateway These requirements FXS Gateway Overview 1 7 FXS Gateway Overview include 1 Acomputer with an Ethernet NIC Network Interface Card installed 2 Acomputer equipped with communications software configured to the following parameters VT100 terminal emulation 9600 Baud No parity 8 Data bits 1 stop bit Flow Control set to None 3 Use Internet Explorer 5 5 and later or Netscape Navigator 6 and later versions 4 Analog telephone set 9 Software tools Gatekeeper optional After the FXS Gateway is properly set up you can make future changes to

FXS H.323 Gateway User Manual (2FXS, 2AFXS

Contents

Download Pdf Manuals

Related Search

Related Contents