VL770 User`s Manual
Contents
1. or keyin OSD Root menu to enter Video Enhance Mode There will be a small OSD ICON on right hand corner of screen while apply the mode The ICON will be disappear after 2 sec Step 2 Press any key to get other Enhance Video Mode in sequence Ex Cool Warm Soft Normal If the OSD Root menu appear again after running the sequence It means you are in Normal operation 11 Enhance Video Adjust 4 gt Select NORMAL E MODERMODEREMODE ZOOM COOL WARM SOFT When the monitor detects an excessive signal input the warning message box illustrated below will appear on the screen to refrain user from further usage and advise user to adjust the signal input in compliance to the stated safe range 12 4 Specifications CRT 17 inch 16 viewable diagonal nomoral flat square tube pure flat tube 90 deflection anti glare anti static semi tinted CRT with Invar Shadow Mask Dot pitch 0 25mm PF 0 27mm FS Max Resolution 1280 x 1024 Display color Unlimited Scanning frequency Horizontal 30K 72KHz Vertical 50 135Hz Display area Factory presetting 310 x 230 mm W x H Video bandwidth 100 MHz 3dB nominal Input signal Video Analog 0 7 0 1Vp p 750hm 5 Sync Separate TTL level Power supply 100 240 Vac 50 60 Hz Power consumption Normal lt 75W Standby lt 5W Active Off lt 5W Recommended ambience Opera2. gt Select t Adjust gt Select 5 Language Allow user to select OSD menu in preferred languages Press or to make the selection Language English ug AdJjust 4 gt Select Adjust 4 gt Select 6 Others Other function selections a OSD H Position Allow user to adjust the horizontal position of OSD menu on the display b OSD V Position Allow user to adjust the vertical position of OSD menu on the display c Information Current display resolution Hsync frequency Vsync Frequency and polarity d Smart setting Remind user to take a break from starting at the screen after preset time period Press or 10 set the timer The message box will appear on the lower right hand side of the screen at the preset time To avoid the interference of the message box simply press any key except power key It will appear again at the preset time in later sessions 10 OSD H Position t Adjust lt gt Select Adjust gt Select Information Smart setting AdJjust 4 gt Select Adjust 4 gt Select 7 Exit Terminate OSD menu on the screen 8 Enhance Video Option A Normal Normal operation B Zoom Full screen display C Cool Enhance the video within 9300 color temperature D Warm Enhance the video within 6500 color temperature E Soft Enhance the video within 5500 color temperature Operation Note Step 1 Press
3. 92 07 Email Internet development tco se Current information regarding TCO 99 approved and labelled products may also be obtained via the Internet using the address http www tco info com Environmental Requirements Flame retardants Flame retardants are present in printed circuit boards cables wires casing and housings Their purpose is to prevent or at least to delay the spread of fire Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances Most flame retardants contain bromine or chloride and those flame retardants are chemically related to another group of environmental toxins PCBs Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects including reproductive damage in fish eating birds and mammals due to the bio accumulative process Flame retardants have been found in human blood and researchers fear that disturbances in foetus developments may occur TCO 99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine Flame retardants are allowed in the printed circuit boards since no substitutes are available Cadmium Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displays Cadmium damages the nervous system and is toxic in high doses The relevant TCO 99 requirement s
4. joint effort by the TCO The Swedish Confederation of Professional Employees Svenska Naturskyddsforeningen The Swedish Society for Nature Conservation and Statens Engergimyndighet The Swedish National Energy Administration Approval requirements cover a wide renge of issues environment ergonomics usability emission of electric and magnetic fields energy consumption and electrical and fire safety The environmental demands impose restrictions on the presence and use of heavy metals brominated and chlorinated flame retardants CFCs freons and chlorinated solvents among other things The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to each country where the company implement its operational policy The energy requirements include a demand that the computer and or display after a certain period of inactivity shall reduce its power consumption to a lower level in one or more stages The length of time to reactivate the computer shall be reasonable for the user Labelled products must meet strict environmental demands for example in respect of the 18 reduction of electric and magnetic fields physical and visual ergonomics and good usability Below you will find a brief summery of the environmental requirement met by this product The complete environmental criteria document may be ordered from TCO Development SE 114 94 Stockholm Sweden Fax 46 8 782
5. 0Hz to 135Hz 17 inch 16 0 viewable Normal flat square tube 0 27mm dot pitch m Pure flat tube 0 25mm dot pitch 1 Microprocessor based design with digital controls Plug and play ready m Unlimited colors Compatible with standard IBM VGA Super VGA XGA modes as well as VESA resolution standards Universal power supply m Til amp swivel base m MPR II compliant m TCO 99 compliant optional VESA Display Power Management DPMS compatible m Microsoft Windows 95 98 NT 2000 ME compatible VESA Display Data Channel DDC 1 2B compatible m EPA Energy Satr compliant power saving 2 Installation Setting up your monitor is very easy Just make a few simple connections and adjustments The following procedure is to guide you to the proper usage of this product 2 1 Check List Before operating this monitor please make sure that all of the following items are included Monitor m Tilt amp Swivel base Power cord User s guide If any of these items is missing please contact your dealer for technical support and customer service 2 2 Install The Monitor Base Turn the monitor upside down Align the eight holders on the swivel base to the holes on the bottom of the monitor Press it firmly downward and push it forward toward the monitor front until the two latches match 2 3 Power Cable Connection Connect the female end of the power cable to the Power Input receptacle on the ba
6. User s Manual CM1772PF CM1772FS CT1772PF CT1772FS ID B 17 16 0 viewable Ultra High Resolution Plug amp Play Ready Multi Frequency FS PF Color Monitor oc b c OSD Control Safety Precautions en 3 1 Introduction su 4 1 1 General Information ne 4 1 2 Features ofthe Monitor 4 2 Installation aaa 5 2 1 Check List Dc Z5 5 ene 5 2 2 Install The Monitor Base een 5 2 3 Power Cable Connection 0 e 5 2 4 Signal Cable Connection 6 25PowerOn 9 lt 0 lt 6 2 6 Adjust The Picture 6 3 Operation 5 7 3 1 To Operate The Monitor 0 7 3 2 Image Adjustment enn 8 3 3 OSD Main Menu 0 2 8 4 Specifications 13 5 PowerManagement 0 0 enn 14 6 Timing Guide 15 T PinAssignment 0 aan 16 8 Regulations 17 Safety Precautions Please read all of the following instructions before use Follow all warnings and instructions marked o
7. aphics adapters If the monitor recognizes one of the preset timing signals it will recall that mode and any stored display adjustments you have made However the monitor is multi scanning and can accept any signal within its frequency range 1 640 480 31 5 60 2 640 480 43 3 85 3 720 400 31 5 70 4 720 400 37 9 65 5 800 600 37 9 60 6 800 600 46 9 75 7 800 600 53 7 85 8 1024 768 48 4 60 9 1024 768 56 5 70 10 1024 768 60 75 11 1024 768 68 7 85 12 1280 1024 64 0 60 Refresh rate 15 7 Pin Assignment The pin assignment of the connectors is listed below for professional use only Please do not attempt to alter the connections yourself as this may seriously damage the monitor 1 Red Video input 2 Green video input 3 Blue video input 4 Ground 5 NC 6 Red video ground 7 Green video ground 8 Blue video ground 9 NC 10 Ground 11 Ground 12 DDC SDA 13 Horizontal sync 14 Vertical sync 15 DDCSCL 16 8 Regulations FCC compliance This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits
8. ck panel of your monitor and plug the male end into the power outlet Power Cord 2 4 Signal Cable Connection The monitor has an built in signal cable with a male 15 pin mini D sub connector Attach this connector to the female 15 pin receptacle of your video adapter Be cautious when inserting the cable properly into the graphics card adapter If the cable does not seem to fit it may be facing the wrong direction Turn the cable over and try to match the shape of the connector with the graphics adapter Secure the connection with the screws on the connector 2 5 Power On Power on both the monitor and your computer There will be a short delay approximately 2 seconds before the image appears After the monitor is powered ON the LED lights up in green If the LED flashs in orange check the video cable connection 2 6 Adjust the Picture Adjusting the picture is necessary to obtain the best visual display A complete description of the control functions is covered in the next section 1T Note To minimize eye fatigue we suggest you allow a minimum viewing distance of 18 inches 3 Operation Make sure you carefully follow the Safety and Installation ins
9. es Refer all servicing to a qualified service personnel Keep this instruction manual for later use Note Unplug this product and contact qualified service personnel if The power cord or plug is damaged or frayed product has been exposed to rain or water The product does not operate normally when used properly Improper adjustments have been made product has been dropped or damaged product does not achieve maximum performance 1 Introduction 1 1 General Information Thank you for purchasing our monitor This monitor is a high performance multifrequency color monitor With state of the art electronics this monitor is capable of resolutions up to non interlacing 1280 x 1024 The intelligent microprocessor based design enables the monitor to automatically synchronize and adjust to most common video modes The OSD Control allows you to easily and simply make precise screen format adjustments while user programmability provides cross platform compatibility The monitor features EPA Energy Star compliant VESA DPMS Display Power Management Signaling compatible power management The monitor has been designed to meet Swedish MPR II and TCO 99 guidelines for electromagnetic and static emissions We truly believe you will enjoy using the monitor Thank you for choosing our monitor 1 2 Features of the Monitor Multi scanning at horizontal frequency of 30KHz to 72KHz and vertical frequency of 5
10. for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help WARNING This device has been tested and found to comply with the limits of a Class B digital device The accessories associated with this equipment are as follows e Shield video cable Change or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment 17 TCO 99 Environmental Labelling TCO 99 only Congratulations You have just purchased a TCO 99 approved and labelled product Your choice has pr
11. hen OSD menu will appear 2 Press lt or gt to locate the cursor where you want to access 3 Press or 10 confirm your selection 4 Press or to adjust the value you want 5 Press lt or gt to EXIT icon and press or and then OSD menu will be closed or keep the key free for at least 12 seconds and then OSD menu will be closed automatically 3 3 OSD main menu 1 Picture Screen main adjustment A 2 6 Contrast Adjust the contrast level on the display Brightness Adjust the brightness level on the display Horizontal Position Shift the display to the right or left Horizontal Size Increase and decrease the display width Vertical Position Shift the display up or down Vertical Size Increase and decrease the display height Pincushion Bend the screen display inward or outward on the fringe Trapezoid Adjust the top and bottom display to even width Parallelogram Adjust the tilt of the display to the left or right Bow Bend the sides of the display in the same direction Top Corner Square off the display s top corners Bottom Corner Square off the display s bottom corners Recall While in a preset video mode press the or key to reset all customized display settings to factory default setting Note Press lt or gt key to locate the cursor whe
12. n this product When cleaning this monitor first unplug it from the wall outlet Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use this product where water spills may occur Do not place this product on an unstable surface to prevent it from falling To protect this monitor from overheating slots and openings on the top and bottom of this unit use for ventilation should never be blocked Never place the monitor near a radiator or heating element Only operate this monitor from the power source indicated on the marking label If you are not sure of the type of power source available in your area consult your dealer or your local power company This product is equipped with a 3 wire grounding type plug For safety this device is meant to be used with a grounding type power outlet If you do not have one contact your electrician to replace your obsolete outlet Do not use a 3 to 2 prong adapter Do not allow anything to rest on the power cord or leave any cords hanging where people frequently pass by If an extension cord is used with this product make sure that the total amperage ratings do not exceed the extension cord s amperage or 10 amperes Never puncture any objects through the walls of the monitor High voltage points could result in electric shock fire hazard or cause a short circuit Never attempt to service this product yourself Opening this unit may expose you to dangerously high voltag
13. ovided you with a product developed for professional use Your purchase has also contributed to reducing the burden on the enviroment and also to the further development of environmentally adapted electronics products Why do we have environmentally labelled computers In many countries environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment The main problem as far as computers and other electronics equipment are concerned is that environmentlly harmful substances are used both in the products and during their manufacture Since it is not so far possible to satisfactorily recyle the majority of electronics equipment most of these potentially damaging substances sooner or later enter Nature There are also other characteristics of a computer such as energy consumption levels that are important from the viewpoints of both the work internal and natural external environments Since all methods of electricity generation have a negative effect on the environment e g acidic and climate influencing emissions radioactive waste it is vital to save energy Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy What does labelling involve This product meets the requirements for the TCO 99 scheme which provides for international and environmental labelling of personal computers The labelling scheme was developed as a
14. re you want to access Press or key to adjust the value you want Contrast Adjust 4 gt Select AdJjust 4 gt Select 2 Geometry Screen secondary adjustment Rotation Adjust the tilt of the display V Moire Reduce the optical effect of wavy lines or ripples on the display image in the horizontal direction Over adjustment the moire will cause the effect of the shaking and poor focus on the screen H Moire Reduce the optical effect of wavy lines or ripples on the display image in the vertical direction Over adjustment the moire will cause the effect of the shaking and poor focus on the screen V Focus Adjust the focus of the display image 3 Degauss Press the or key to remove any discoloration from the display image due to electromagnetic field buildup 4 Color managment a Adjust color temperature in three different preset modes b Adjust user s customized R G B color level a Press lt or gt to color temperature Press or to select user s preferred color temperature mode which remains active unless the alternation is made next time Press or to USER icon to define color temperature Press lt or gt 10 choose R and or G and or B for adjustment Press or key to adjust the values of RGB color level Color management Color management t iaAdjust
15. tates that batteries the colour generating layers of display screens and the ectrical or electronics components must not contain any cadmium Mercury Mercury is sometimes found in batteries relays and switches It damages the nervous system and is toxic in high doses The relevant TCO 99 requirement states that batteries may not contain any mercury It also demands that mercury is not present in any of the electrical or electronics components associated with the display unit CFCs freons The relevant TCO 99 requirement states that neither CFCs nor HCFCs may be used during the manafacturing and assembly of the product CFCs freons are sometimes used for 19 washing printed circuit boards CFCs break down ozone and thereby damage the ozone layer in the stratosphere causing increased reception on earth of ultraviolet light with e g increased risks of skin cancer malignant melanoma as a consequence Lead Lead can be found in picture tubes display screens solders and capacitors Lead damages the nervous system an in higher doses causes lead poisoning The relevent TCO 99 requirement permits the inclusion of lead since no replacement has yet been developed Bio accumulative is defined as substances which accumulate within living organisms Lead Cadmium and Mercury are heavy metals which are Bio accumulative 20
16. ting temperature 41 F 104 F 5 C 40 C Operating humidity 10 90 Storage temperature 4 F 140 F 20 C 60 C Dimensions 410 x 401 x 425 W x H x D Weight Net 15Kg 33lbs Gross 17Kg 37 4lbs Certifications UL CUL TUV GS CE DHHS FCC 8 MPR I TCO 99 optional Power Management EPA Energy Star VESA DPMS 13 5 Power Management The power management feature enables this monitor to recognize VESA DPMS Display Power Management Signaling signals from a VESA DPMS video adapter and power down to less than 5 watts of power consumption There are three status to power management On Standby and Active Off In the On mode the monitor and computer are in operation and the LED is green When the power management feature is activated the screen will be blank and the LED will flash in orange indicating that the monitor has been powered down to Standby mode In the Standby mode all circuitry in the monitor is shut down except for a low power detection circuit This circuit allows the monitor to turn on when the computer system Wakes up when you move the mouse 14 6 Timing Guide This multifrequency monitor operates at horizontal frequency of 30K to 72KHz and vertical frequency of 50 to 135 Hz The microprocessor based design offers auto syncronization This monitor offers 12 preprogrammed settings that cover most of the common video modes supported by popular gr
17. tructions before operating your monitor You may also want to familiarize yourself with the Image Adjustment section of this manual before making any operational adjustments 3 1 To operate the monitor 1 Turn on the monitor by pressing the power button once The power LED lights up and the monitor demagnetizes itself for about 4 seconds Power up the system Once the system is completely powered up the LED power indicator on the monitor should be green If not check the connections 4 Use On Screen Display to adjust the controls needed to get the best picture Experiment with the display settings to choose the optimized image size and position for you refer to the Image Adjustment section of this manual for Instructions ID A ID B A Power button B LED power indicator C Function key Note If you need to disconnect the power cord from the wall socket or monitor for any reason be sure to wait at least 30 seconds after you turn off the monitor before you unplug it This allows the monitor to discharge any static electricity from the screen surface 3 2 Image Adjustment The four control keys are designed to provide full user friendly programming capabilities in one simple to use location This allows you to choose either of the control keys and make necessary adjustments To adjust visual settings 1 Press or or lt or gt and t
Download Pdf Manuals
Related Search