Home

Integra32 User Manual - Sharp`s Lock & Alarm

1. Global Links like Global APB require the interaction of the PC These links cannot be executed if the PC is not online As with local links you choose which event on what device will cause the link to be executed Then you can choose up to eight things to have happen These links can be executed on any panel in the system Details on programming links can be found in Chapter 5 under This PC100 interface uses the DSC IT100 to allow communications between the Integra Access Control System and the DSC Power Series Burglar Alarm panel The PC100 is programmed through the Integra32 Software Version 3 7 18 or higher and is designed to be Stand Alone While the host is offline the PC100 continues to monitor activity in the Access Control System allowing interaction between the Access and Alarm Systems Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 140 Chapter 9 Links General Panel Properties x General Keypads PIN Code Links Inputs Address Description J2 Pe OO 32 Fanel type pc100 IT100 D5c coo wow Address The address 32 1s automatically selected at the time of creation and cannot be edited Description To change the default description simply type over it Panel Type The panel type is chosen when the new panel is added and cannot be edited later Enable If the enable check box is not checked then the panel will not be
2. 1 TouchSkar Autostar Mew Finger Print Device OR REH Finger Print Devices do New E Edit x Delete 8 Configure E System settings Description dedo Reader bir Senes 1 Reader 1 test email This selection is only available if the optional license for the Finger Print Reader has been purchased and installed These windows vary as per the manufacture of FP reader Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 150 Chapter 11 Tools Finger Print opens a screen from which to manage the Touchstar readers or any other FP Reader and their finger print data Check with Touchstar for more detailed information on individual settings E Touch Star Configuration A a a A O ES RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 151 Chapter 11 Tools Query Finger Print Reader Query Finger Print Reader i x User Existance of Finger Prints Delete User Total of users Device ID Com Port Buad Rate i 38400 Card r Query Response Use this selection to query Touchstar finger print readers For some fingerprint readers this option opens the same window as Finger Print Readers This selection is only available if the optional license for the Finger Print Reader has been purchased and installed These windows vary as per the manufacture of FP reader Integra32 User s Manual RBH Access
3. Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 70 Chapter 5 Programming Time Outs Timers can be set from 0 127 seconds or minutes Setting a timer to zero will disable it Unlock ine 5 Sec Extended unlock time 10 Cer DHO samaj 5 sec DHO alarm sfs 7 Timed anti passback Poo Hsec y Repeat Ignore time o Hl sec y Unlock Time This 1s the time the Door Unlock output 1s turned on for Extended Unlock Time For the Cards given the Extended Unlock Time privilege the Door Unlock output will turn on for this length of time instead of the regular Unlock Time DHO Warning If a door 1s still open when the Lock Time expires the Door Held Open Warning timer will start When the Door Held Open Warning time expires the Access Point will go into Door Held Open Warning posting DHO Warning message and pulsing the reader s buzzer DHO Alarm If a door is still open when the Door Held Open Warning time expires the Door Held Open Alarm timer will start When the Door Held Open Alarm time expires the Access Point will go into Door Held Open Alarm posting DHO Alarm message and turning on the reader s buzzer continuously Since the DHO Alarm timer starts when the DHO Warning timer expires if the DHO Warning time is set to zero then the DHO Alarm timer won t be started RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 71 Chapter 5 P
4. It s not a matter of if a hard drive fails but when Unknown Integra32 Backup Configuration Wizard x This wizard will help you to backup Integra data files i Run backup now C Configure auto backup d Back Next gt Firnteh Run Backup Now Run Backup Now option is used to run an immediate backup Follow the wizard for this option From the Backup Configuration Screen the destination folder into which the backup files will be saved is selected Zhe default destination setting is Integra32 backup Checking Data Files will back up the data files particularly AxlogxLT mdb AxsystLT mdb amp AxuserLT mdb While checking History Files will backup all of the currently held history files Cardholder Image Files when checked will back up the cardholder pictures The Log Screen will display these files as they are backed up RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 147 Chapter 11 Tools Integra32 Backup Configuration Wizard a x Select destination tolder E Program FilesSrbh lntegrad T est Backup E Select the file s to backup Data Files History Files Cardholder Image Files Cancel Back Het gt Finish Contigure Auto Backup The auto backup can be configured to happen at a specified time on specified days of the week For example the backup can be performed at 11 30 a m every Monday or at 10 15 p m every Tuesday and
5. ha ata Access level Activation date 4 2 ele Deactivation date Usage Count Time dl 1 status FIN Code Type i Ignore Antipassback P Ignore Auta old i Unlock Privilege 2 IM High Security Privilege 4 I Link Execute Privilege 345 Extended unlock time Disabled H Add Edit Remove Lopy le 1 of 2989 gt fl Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 96 Chapter 6 Cardholders Fields and Options The cardholder window contains following fields and options File Exit Select this option to leave the Cardholder screen New To add a new cardholder click on the New button then the cardholder s information can be entered Edit To make changes to an existing cardholder click Edit then make the necessary changes Save To save changes made to a cardholder click Save Cancel Cancel will exit the edit mode without saving any changes to cardholder Delete Cardholders that are no longer required can be removed from the database with the Delete button All cards with this cardholder are deleted with it Search To search for a cardholder click Search There are many fields to search by select one and enter your perimeters then click Search Multi Cards Multi Cards will open a utility to add multiple cards in a sequence to the cardholder utility as well as to the panels F Print F Print will open the finger print enrolment screen depending upon
6. 3 8 22r4 2 SP15 717 Chapter 5 Programming Advanced x General Modes Time outs Links Alarms CCT Advanced Entering rea W Standard AFE Enabled Mone E siting rea None Exit Reader Installed e AP Activity Access Requested Access Granted Access Denied Lancel Standard APB Enabled The check box is used to turn on antipassback Soft antipassback will still grant access even though APB has been violated hard APB will not Global Local Antipassback For Global Antipassback to work the Integra32 system must be online and PC Decision Required must be turned on in the Modes tab of the Reader Properties window for all of the appropriate readers otherwise the panel will default to Local Antipassback within an IRC 2000 URC 2000 Global Antipassback allows a cardholder s area to be reset cleared meaning they are not logged into any area With Local Antipassback the cardholder is either In or Out never neither always one or the other Local Antipassback may be used with or without the Exit Reader Interface If the Exit Reader Interface is not used when Local Antipassback is configured then either the A side or the B side reader port not both needs to have its TAM terminal grounded The side with the grounded TAM terminal will be the Out reader and the side without will be the In reader Entering Area amp
7. Track Photo Assets p visiting SS PO E Firstname PO Department Employee Card fo Last Ghecked In Last Visited jscad Checked In fa9 2012 9 15 18 AM Checked Out 4719 2012 9 27 34 AM Under the Assets tab in edit mode the operator can enter data concerning anything that the visitor brought with them to the site To print a receipt for these assets click on the Receipt button Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 116 Integra isitor Receipt x AFTI a 1 oft Preview Lastname Firstname Cardnumber Wisting Assets Signature Visitor Date Malik Saleena 66666 Card 82 Laptop Brown bag Malik Saleena A201 Chapter 7 Visitor Management gt gt oh Assets Receipt 4 25 2012 11 11 264K If there is any information entered under a visitor s asset then a reminder will pop up when the visitor checks out After the visitor has checked out this asset data is deleted RBH Access Technologies Inc Integra32_ User s Manual Integra32 3 8 22r4 2 SP15 117 Chapter 7 Visitor Manager Track E Integras2 AxiomLite Security System isitor E wx o A amp amp GZ Add Edit Save Delete ance Search CheckIn Check Gut Receipt Track E mail Lastname Malik Firstname Salsena Mational ID Card Mumber EE General Photo Track visiting Lastname E Firstname DEE Employee Card
8. 1 of 2989 gt fl Department can be selected form the pull down list instead of being typed in Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 106 Chapter 6 Cardholders Photo Tab You can select an already saved picture of the cardholder in the Photo tab or you can acquire a cardholder s image The picture is then saved in the Integra32 Images folder You can select or print one of the already saved templates for the cardholder in this tab if the badging option 1s part of the software Integra32 AxiomLite Cardholders E o XX l New Edit Gancel Delete Search ls F Print Receipt Multi Cards Last name First name Initials Cardnumber ANDRULIS STEPHEN Cards Profile Fhoto Notes More Fields Picture File 1 atwalt jpg mm Picture File 2 ara Signature File 1 as Signature File 2 P J lt 1of2989 Use the Card Front amp and Card Back buttons to view both sides of the badge RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 107 Chapter 6 Cardholders Notes Tab Any other relevant information concerning a cardholder can be saved under the Notes tab Integra32 AxiomLite Cardholders File E o gt x aajo Mer Edit Cancel Delete Search Multi Cards F Print Receipt Last name First name Initials Cardnumber ANDRULIS STEPHEN lt 1 of 2989 gt
9. History Reports Holidays 162 123 9 104 69 69 25 71 20 21 22 8 90 138 11 71 105 97 100 15 70 144 130 162 69 92 24 132 78 140 166 129 105 70 105 120 33 RBH Access Technologies Inc How to Execute a Command I Ignore Antipassback Import Utility Inhibit ID Input Points Commands Input Properties Inputs Alarms CCTV Details Links Integra32 Database Integra32 Server Client Network Setup Integra32 Database Maintenance Integra32 Registration Integra32 Security System Integra32 Site Configuration Interlock Introducing Integra32 IRC2000 Properties K Keypad Commands L License amp Warranty Link Execute Privilege Links Local Antipassback Log In amp Out Ctrl L Login Logout Toolbar Button M Magnetic Encoder Setup Menu Options Messages Monitor Screen Multi Cards N Networks Advanced Comms Direct Connect Ethernet Connect Modem Connect General O Options Out Reader Output Points Commands RBH Access Technologies Inc 13 104 150 70 17 81 85 82 81 84 30 162 164 161 161 15 45 25 167 104 105 5 78 4 8 132 38 12 97 98 39 43 40 40 42 41 39 79 18 Index Output Properties 86 Outputs CCTV 87 Details 86 Links 89 P Panels 44 Alarms 47 Code Reader Links 48 Dial Out 49 Site Codes 46 Panels Commands 19 PC Decision Required 70 PC100 52 Permanent Command 13 Preview
10. It 1s recommended that the user be familiar with the Risco Group panel and has the ability to program PIN codes and parameters into the panel The PC100 interface has been designed to connect the Integra32 network to the Risco Group alarm panel through the option or keypad bus It will emulate a keypad when a link has been provided and report status to the Integra network when included in the list of keypads In order for the alarm panel to poll the emulated keypad the keypad assignment for the alarm panel should be programmed Keypad addresses 1 10 connect to the keypad bus and addresses 11 15 is connected to the option bus The PC100 can monitor all keypads on the bus that are listed under panel properties Keypads A Link to an Event will use an emulated keypad to enter a password followed by a command If the password is not programmed into the alarm panel no operation will take place Whenever a command is executed the green Health LED will turn on The green Health LED will turn off when the alarm panel finishes its poll to the keypad Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 58 Chapter 5 Programming General Panel Properties x General Keypads PIN Code Links Address Description J2 PE OO 32 Panel type Pct 00 Risco Group coo Ao Address The address 32 is automatically selected at the time of creation and cannot
11. User Mumberl RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 155 Chapter 11 Tools Card Import Configure Import Utility The ntegra32 Card Import Utility is used to import cards and cardholder data from a text file or SQL database into your Integra32 database Card Import Utility Integra32 Card Import Utility Click to Configure the card import Run Import utility View Log File dd Config Import utility 44 Select Config Import Utility to setup the import parameters This selection is only available if the optional license for the Card Import Utility has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 156 Chapter 11 Tools Import from a text file Import Wizard l The wizard will help you to enter bulk data in the card holder table Cards can either be imported From an external text File or M5 SOL Server Local machine should hawe SOL Server running or SQL Client installed C Imports Cards from SQL Server Cancel Back Meck gt Finish Enter the source and destination paths as well as the delimiting character Use Option M Delete File upon successful Import If want to delete the file you are importing from after the import is complete M Remove cards not found in Import file This option will add update the cardholders from import file and delete all the
12. fl Notes entered here can be displayed in the Access Point Activity window when it is expanded to show More Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 108 Chapter 6 Cardholders More Fields Tab Any additional information required for cardholders can be saved in More Fields tab Integra32 AxiomLite Cardholders S x File E o x O L Mew Edit Cancel Delete Search Multi Cards F Print Receipt Last name First name Initials Cardnumber ANDRULIS STEPHEN User Humber User Humber fo o User Text 1 User Text 2 User Text 3 User Datel User Text 4 User Text E User Texth E lt 4 1 of 2989 gt fl The user can rename the fields under this tab by clicking on Card Custom Fields from Tools menu RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 109 Chapter 6 Cardholders Tools Reports Help E Backup old Cards lS Finger Print i Query Finger Print Reader 3 Badge Template Designer Card Custom Fields Card Import Double click on the Label of any of the fields to be changed in edit mode and rename the field name Integra32 AxiomLite Cardholders E x E M Edit Save Cancel Last name First name Initials Cardnumber More Fields User Mumberl xl Enter New Name User Text 1 Cancel User Text 2 Drivers License User Text 3 User Date User Text 4 User Text 5
13. 89 Chapter 5 Programming Elevators aa Panel 1 aa Panel 2 aa Panel 3 H Access Points Inputs E Outputs EE BE e ator H A Panels H Panel 5 roperties 2 Delete The URC2000 Elevator Control can control up to two elevator cabs and thirty two floors Y ou can split the thirty two floors between the two doors any way you like E Add Elevator Oy x Description New Elevator Reader Available terns Selected ltemz Ok Cancel Access Points used for elevator control will have all the standard functionality of regular Access Points except for Antipassback and Interlock and unlocking these Access Point will only affect the outputs assigned to the URC2000 controller and not the floor outputs Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 90 Add Elevator Elevators Description Cab A Reader Reader 5 la Available lkems Description 1t Floor Cab B 2nd Floor Cab E 31d Floor Cab E 4th Floor Cab B Sth Floor Cab B bth Floor Cab B th Floor Cab B oth Floor Cab E Sth Floor Cab E 10th Floor Cab B 11th Floor Cab E 12th Floor Cab B Selected Items Description Tst Floor Cab end Floor Cab 4 ad Floor Cab A 4th Floor Cab 4 Bth Floor Cab A bth Floor Cab 4 th Floor Cab A oth Floor Cab A Sth Floor Cab A 10th Floor Cab A 11th Floor Cab A 12th Floor Cab A Chapter 5 Programming 15 x OR Cance
14. A ADD ARO O RO cantan 166 LICENSE WARRANTY iii dadas io cionado adan Ron R e Adi oo iaA AR i dada adan in R e Ade oo adn Ain Rida Moa clan donar Acad 167 INDEX A O rsaadacbioasoiwandna EES N E N AES 168 IRERADER COMIVEN ES wsscesstasstcsssasscasscascsnancavaceastasstacniasaaaateasassansabaseat basdiacndasaassveasassanen bashes bandtaandastsaabeasausaseasasaants 171 RBH Access Technologies Inc Intega32 User s Manual Integra32 3 8 22r4 2 SP15 About This Manual About This Manual This manual documents how to install and use the Integra32 Security Management System as developed by RBH Access Technologies Inc The Integra32 system represents the latest in access control technology specifically designed for the smaller application Its intuitive graphical interface allows users to take advantage of the power of the Integra32 with a minimal amount of training Read this manual 1f you are An operator who monitors security and access using Integra32 A system administrator who updates Integra32 gt s database The system technician that installs and configures the Integra32 onsite Before reading this manual This manual assumes that you Are familiar and comfortable with a personal computer Know how to use a mouse 9 Are familiar with the Windows operating environment Conventions in this manual Menu options window titles fields and buttons are indicated by italic typeface For example choose Acce
15. Exiting Area Antipassback tracked across multiple IRC 2000s is called Global Antipassback 22 Antipassback tracked on one side of a panel RC 2000 is called Local Antipassback Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 78 Chapter 5 Programming An Entering Area must be selected for APB to work Selecting only an Entering Area will setup Reader APB In Reader APB the Entering Area is compared to the cardholder s current location If they match there is an APB violation By adding an Exiting Area you setup Area APB Area APB not only check that the area the cardholder is entering isn t the area they are in but also verifies that the area they are exiting 1s the area they currently are in providing a higher level of APB APB Access Points work well with Exit Reader Interfaces The In reader uses the configuration of Entering Area and Exiting Area as programmed while the Out reader uses the inverse The Out reader gets its Entering Area from the data programmed into Exiting Area and vice versa Exit Reader Installed Selection of this option will configure the system to allow separate Global links for the In reader as for the Out reader The Exit Reader Interface module is used to connect two readers to a single reader port providing both In and Out readers oe To use the Exit Reader Interface module the IRC2000 must be running firmware 10
16. PIN codes must match PIN codes programmed into the DSC system in order for commands from the emulated keypads to affect the DSC system Only eight PIN codes may be entered here Pin Code Name Enter here a description or name for each PIN code RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 65 Chapter 5 Programming Links Panel Properties x General Keypads PIN Code Links Inputs 1 coo aww Event Select from a pull down list the triggering event Device ID Choose the appropriate device to execute the selected command from a pull down for the selected event Card Enter the card number if applicable that will trigger the selected command when it is associated with the chosen device and selected event e g execute the command when card 1234 is granted access at reader 1 Command Select the command to be executed on the chosen keypad from a pull down list Arm Keypad Disarm Keypad or Arm Perimeter Keypad Choose which keypad the command 1s to be executed on Pin Code Select a valid PIN code The command will be executed as though this PIN code had been entered Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 66 Chapter 5 Programming Inputs Panel Properties Input E Input E Input 7 Zone There are 256 zones Description The zone name or description can be ed
17. Reader B Details Select the Circuit type and Abort Delay under the Details tab e Inputs can be Normally Open or Normally Closed One resister Two resister or No resister e Abort Delay is set in second minutes maximum 127 minutes The input must be tripped for this amount of time to cause an alarm If the input is cleared before the time expires then there won t be an alarm For General Purpose inputs additional programming 1s required under the Details tab General Details o a A CETV Links Alarms Circuit type Abort Delay INC 1 Resistor ls fse 7 Options Forced arm alarm e Report while armed e Report while disarmed Disarm during time group oz After Hours RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 81 Chapter 5 Programming Reporting or Non reporting Are messages from this input to be displayed on the Log Screen and logged Forced Arm Alarm or Not Forced Arm Alarm Forced Arm Alarm will force an input into alarm if it is armed while it is abnormal Disarm during Time Group Disarm the input during a schedule CCTV General Details CLT Links Alarms Camera Number AA ooo DWA IP Address Port Humber IS This tab 1s available for editing only 1f CCTV license has been installed otherwise we can only send messages to DVR servers The information in this tab is used to inte
18. Reports 121 Print Area Report on Input 129 Program Groups 160 Programming 30 Properties Notes Tab 108 Q Query Finger Print Reader 146 R rbh ini 7 Receipt 113 Registration 164 Repeat Ignore Time 72 Reports 6 120 Reset Area 29 RTE Bypass DC 70 Run Backup Now 141 S Schedules 34 Semi Permanent Command 13 Set Area 23 Set Date Time 20 21 22 Site Configuration 161 Status Screen 10 System Messages 135 System Options 128 System Status 12 System Status Toolbar Button 8 T Time Zone Difference 43 Time Zones 34 Timed Antipassback 72 Timed Command 13 Toolbar Buttons 7 Integra32 User s Manual Integra32 3 8 22r4 2 SP15 175 Index Tools 5 141 Users 30 Track Visitor 118 119 y U i Version 20 21 22 Unacknowledge 29 Visitor Assets 116 Unlock Privilege 105 Visitor Manager 111 Unlock Schedule 70 Visitor Reports 127 URC2000 Properties 45 Visitor Tracking 118 119 URC2000 with ELV 49 Visitors Status 24 Usage Count 104 Visitors Toolbar Button 8 User Fields Visitors 139 VM Configuration 138 User Options 129 Void Cards 143 Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 176 Reader Comments Reader Comments RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 177
19. STEPHEN Cards Profile Photo Notes More Fields 449968 Access level Activation date 4 2 2012 Deactivation date Usage Count status PIN Code Type Normal i onore Antipassback 7 Ignore Auto Yoid MW Unlock Privilege 2 High Security Privilege 4 i Link Execute Privilege 3 5 Extended unlock time Disabled e Add E dit Remove Copy 4 1of 2989 gt I Access Level Select previously defined access levels from the pop up window Access levels determine when and where an access code 1s valid RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 103 Chapter 6 Cardholders Activation Date MM DD YYYY This field is automatically populated with the current date and time when a new cardholder 1s added to the system Deactivation Date MM DD YYYY To deactivate a cardholder enter the current date or a date in the future on which that cardholder is to be deactivated The cardholder will be deactivated automatically on the specified date This field defaults to 1 January 2038 Status Card status is shown here generally active or inactive depending on the activation and deactivation dates This status can be changed to stolen destroyed expired lost or suspended Usage Count Valid range is 1 255 Enter the maximum number of times the card can be used It reduces the count by one every time the card 1s used at specific
20. Schedules on the Floor Groups Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 94 Chapter 5 Programming Elevator Access Level Access Level Properties i x General Access Level Elevators Access Level Elevator Elevator Floor Groupe Schedule 4th th amp 6th Fo 00 Never 31d Sth amp 10th F 00 Never Ah amp 12h Floor 00 Never ard 6th Sth amp 1 04 Mon Fri amp 00am 5 00pm Ab th amp Sth F 00 Never 31d Sth amp 10th F 00 Never oth amp 12h Floor 00 Mever 3rd Eth Sth amp 1 00 Newer 00 Newer O1 Always U2 Mon Fri 30arn 5 30 pri 03 After Hours 04 Mor En Oars Odon The schedule of any Floor Group can be changed to any schedule as long as no more than four schedules are changed from Never Maximum of 4 Floor groups can be assigned per elevator panel in an Access level If multiple Floor Groups that are given schedules have floors in common than the cardholder will have access to those floors if any schedule allows it RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 95 Chapter 6 Cardholders Chapter 6 Cardholders Cardholders are entered edited by clicking the Cards button from the toolbar of the Main Window x File E Z x i lra ig a Mer Edit Cancel Delete Search Multi Cards F Print Receipt Last name First name Initials Cardnumber ANDRULIS STEPHEN ney 449968
21. Technologies Inc Integra32 3 8 22r4 2 SP15 152 Chapter 11 Tools Badge Template Designer36 File Help Q 6 h e e 1 5 2 0 25 3 0 Is 40 1 Horizontal Card 2 Vertical Card 3 Horizontal ID 4 Vertical ID 5 Customized 2i mn O ho co Plese The Badge Template Designer can create standard or customized badge sizes Select one of the five options available from the Create a new template button of the toolbar Templates can be saved and re opened This selection is only available if the optional license for the Badging Software has been purchased and installed RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 153 Chapter 11 Tools s Badge Template Designer E ioj x File Help 0 4a ae te 00 05 1 0 15 2 0 2 5 3 0 29 40 M Test Front Side xj Faste Insert Text Field Insert Photo Field Insert Signature Field Insert Finger Print Field Insert BarCode Field Insert Shape Field Save Template Save Template 45 Properties Right clicking on the badge will bring up a menu list From here you can add a text photo fingerprint signature or barcode field e Text fields can be static type in your own information or it can get data from a field in the database e g name or card number e Photo fields can also be static so that you can insert your own picture or logo or picture field where you can display the cardholder s image
22. Thursday These backed up files are saved by date the file is designed bkpYYYYMMDD where YYYYMMDD is the backup date and you can set how long they are to be kept If for example you set the backup for Monday to Friday to be kept for 32 days backups older than 32 days will be over written Integra32 Backup Configuration Wizard p x Select the time and day s to run the backup 1F al 2 15 00 am Sure e Mon 4 Tue I Wed Iw Thu fe Fi p Sa Overwrite backed up file after following number of day s Cancel Back Het gt Finish Click Finish to allow the system to run the auto backup at the specified day and time Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 148 Chapter 11 Tools Void Cards From Void Cards the operator can manually void deactivate cards that have not been used for a preset number of days The number of days 1s set under Options System Options E Void Card Utility oj x 6 Print 4 Inactive y Select All Print will produce a hard copy of the cardholders listed at the time Print is selected Q Void will immediately deactivate all selected cards Select All will put a check mark in the select field for all of the listed cards RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 149 Chapter 11 Tools Finger Print34 Finger Print Readers jale Ej Add 5 Edt E Delete E Config
23. User Texth A There are two numeric fields six text fields and two date fields for the user These fields can be used in searches and can be displayed on badges Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 110 Chapter 7 Visitor Management Chapter 7 30 Visitor Management To add a visitor into the system the card they are to use must first be entered into the cardholder screen and configured to Type visitor The Profile Photo and More Fields tabs are actually redundant to visitor cards The Cards tab of course is required while the Notes tab is optional Visitors are entered edited by clicking the Visitors button from the toolbar of the Main Window Integra32 AxiomLite Security System Visitor E o iol x B ii x A g L B y Add Edit Save Delete ance Search CheckIn Check Gut Receipt Track E mail Lastname Malik Firstname Saleena Mational ID Lard Mumber E6666 General More Fields Assets Track Photo Personal Information Reason to Visit Contract work Address Date of Birth City Phone aloe E mail Country Employer Postal Code Time allotted jo Hours Notes Pe visiting Elite PO E Firstname PO E Employee Card jo Last Ghecked In Last Visited stad Checked In 4719 2012 9 15 18 AM Checked Out 1872012 9 27 34 AM This selection is only available if the optional license for the Visitor Man
24. above for the regular URC 2000 URC 2000 Elevator panels have a sixth tab Outputs These outputs on the ELC 08 boards are the only outputs that can be used for elevator control RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 49 Chapter 5 Programming Reader ports on an elevator board can be used for either elevator control or with very limited functionality as access control It is usually recommended not to combine elevator control and access control on the same board When an access point is used for elevator control change all of its default inputs and outputs to general purpose the elevator reader won t need them If you use the access point for access control 1t won t have all of the features that access points on other panels have Access points on an elevator control board will not have Deduct Usage Disable Forced Entry Unlock Schedule First Person Delay RTE Bypass DC Report RTE Antipassback or an Alarm Shunt output Timed commands will act as semi permanent commands Extended Unlock time will be fixed at thirty seconds Door Held Open warning will be fixed at twenty seconds and Door Held Open alarm will be fixed at thirty seconds pago ED III x General Reader Options Site codes Alarms Code Reader Links Outputs Address Description A Panel 5 Panel type WAC2000 with ELC W Enabled Outputs Up to fo
25. available if the optional license for the DVR Software has been purchased and installed 13 This selection is only available if the optional license for the DVR Software has been purchased and installed RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 17 Chapter 3 Monitor Screen Output Points Commands Clicking the Output button on the Command Toolbar depicts the status of output points on the Device Status Screen H a gt gt IN Ar D a a4 E Reader Inputs Outputs Panels Areas Cardholders Keypads Floors Visitors e 4 Output 3 test Ort Panel 79 1 E Outputa pii Panel 79 1 E a A A p i Dut T h Ort Panel 79 1 E G out sd Dif Panel 79 2 A Y Out ea Live Ott Panel 79 2 i Out ey Play Ort Panel 79 2 U Dupre Ort Panel 79 2 G Output 2 Ott Panel 79 3 y wf The following commands for outputs are available by right clicking the selected Output Commands Turn On Turn on an output Turn Off Turn off an output Live Select Live to display live video from the CCTV camera associated with the selected output point Play Play will bring up a DVR history selection screen so that video connected to an event for the chosen output point can be played back 14 This selection is only available if the optional license for the DVR Software has been purchased and installed 13 This selection is only available if the optional license for the DVR Software has been purchased
26. be edited Description To change the default description simply type over it Panel Type The panel type is chosen when the new panel is added and cannot be edited later Enable If the enable check box is not checked then the panel will not be shown in the status screen All Access Point Inputs and Outputs under that panel will also be disabled Disabled items are still in the database but are not considered to be part of the system RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 99 Chapter 5 Programming Keypads Panel Properties x carcel Ao Address This is the address of the keypad in the Risco Group system Name Enter here a description or name of the keypad to be shown in the Integra32 system Emulated Check this box if the Integra32 system will be emulating this keypad and leave it unchecked to monitor an existing keypad Signals from an emulated keypad will be the same as signals from an existing keypad therefore to the Risco Group system there is no difference between an emulated keypad and an existing keypad Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 60 Chapter 5 Programming PIN Code Panel Properties 4 Digit Pin Codes Pin Codes Enter the four digits of each PIN code These PIN codes must match PIN codes programmed into the Risco Group system in order for commands from the emulate
27. correct most corruptions in the databases Those that can t be repaired will produce an error message Integra32 Firmware Upgrade Before Upgrading 1 Before starting the firmware upgrade be sure to know where the upgrade file rbh is located 2 Although upgrading will not affect the panel s memory it is recommended that you download all files to the panel after upgrading to ensure that any new features are properly installed Upgrading After logging in the Upgrade Wizard will come up Browse and select the upgrade file rbh The upgrade file s path will be shown in the box next to the browse button Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 168 Chapter 12 Program Groups Integra32 Firmware Upgrade Wizard f The wizard vill guide you through upgrading the firmvare of IRC 2000 panels Select the firmyvare Upgrade file This must be a valid IRE 2000 Firmware upgrade file D Firmware IRC109BL RBH PA Click Next after the appropriate file has been selected Integra32 Firmware Upgrade Wizard f Select panels to upgrade 1 Panel 1 Metwork 1 2 Panel 2 Network 1 O 3 Panel 3 Network 1 4 Panel 4 Metwork 1 1 Panel 5 Network 2 2 Panel 6 Metwork 2 3 Panel 7 Network 2 DO 4 Panel 6 Network 2 1 Panel 9 Metwork 3 Next select which panel s should be upgraded Then click Next You don t have to select all the panels at
28. each file L If the panel is offline at the time of the download any files that fail to download will be logged on the Log Screen Panel download does not execute itself after the panel comes back online have manually re start the download on that panel Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 22 Chapter 3 Monitor Screen Area and Cardholder Commands Clicking either the Areas or the Cardholders button will bring up a selection window From the Areas selection window you can choose the area or areas you wish to view The Cardholders selection window allows you to choose from the list of cardholders The display will show a list of cardholders based on your selections You will see the area the cardholder 1s logged into and the date time they were logged into that area Y a MA E Fa H a Reader Inputs Outputs Panels reas Cardholders Reppadz Floors Visitors wt E __Nanber tastnane __ Fsiname Deparment area pe A da 454349 Riarh kanty y 53073 Riarh kanty In Area 22712012 3 05 00 E 294 Tester Tester Testing Aa 30094 Tester Testing Sf Anes Vea EEE a 3 MALIK SALEEM A A 460001 Malik Renu A 4 8 Print The following commands for cardholders are available by right clicking the selected cardholder Commands Set Area Set Area is used to change the area that a cardholder is logged into This may be necessary if a cardholder get into an area without reading into th
29. fo Last Ghecked In Last Visited jes Card Checked In jan 9 2012 9 15 16 AM Checked Out g 9 2012 9 2734 AM J d 1of5 b PI The Track tab will display the access points that the visitor has been granted access to since their check in time Simply click on the track button on toolbar to display refresh the information Only visitors that are checked in can be tracked If the visitor has checked out you can get information on where they have been from the Visitor Reports Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 118 Chapter 7 Visitor Management ul 2 G xXx o A 4 5 Add Edit Save Delete ancel Search CheckIn Check Out Receipt Track E mail Lastname Malik Firstname Salsena National ID Card Number e6666 General More Fields Assets Track Photo Fhoto 1 1 Picture Files bilicicr jpg Signature The Photo tab shows all the templates from the badging template module Only the fields valid for the visitor management will be shown on the badging templates in this module RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 119 Chapter 8 Reports Chapter 8 Reports The Integra32 report creation facilities allow you to customize an almost unlimited number of reports and can be used as an extremely valuable management tool From Reports menu you can choose to launch History Report Database Repo
30. for each network Under the Comms tab properties of the port are configured Choose one of the four options available for Port Type works E a Net Network 3 General Under the General tab of the Networks Properties Window network descriptions can be edited Network Properties Y MN gt e w Network 1 RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 39 Chapter 5 Programming Comms Direct Connect The controller network JRC 2000 URC is connected directly to the PC serial port via a RS232 or a RS485 cable Network Properties Dieci Newa SSO a com2 Y 38400 Y Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 40 Chapter 5 Programming Modem Connect The controller network IRC 2000 URC is located remotely and is connected to the PC via dial up modems Network Properties X General Comms Advanced Fort Type Modem Network PC Modem Modem ER 1 Sportster vi 33 6 FAX 9600 Phone Schedule Hang up afters Min Panel Modem Phone Password anaes Init String E0F1 50 14082780008 408418517 HO Select a modem and configure it in the Control Panel to a maximum baud rate equal to that set at the panel e g 9600 Enter the phone number for the network to be called by the PC and the call back phone number for the panel to call Auto hang up time can be set in
31. for this functionality to work software version 3 8 6R4 2 or higher 1s required xi General Database Monitor Language 2 Mame Test operator User ID Jagent Password E AAA Email Address RD TESTING rbhusa com Database The access to database can be defined changed in the Database tab Access to each module of the database can be chosen as No Access Read Only or Read amp Write For some items Read Only access may not be relevant If Read Only access is selected for these items their access will actually be Read amp Write RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 31 Chapter 5 Programming Operator Properties l x General Database Monitor Language Networks Read and Write Panels Read and Write Access Points Read and write Inputs Read and Write Outputs Operators Read and Write Schedules Read and Write Holidays Read and Write Cards Read and write Monitor Access to commands allowed in the Monitor Screen and the Alarm Screen can be defined changed in the Monitor tab Check commands that the user is to have access to and uncheck commands that he she is not to have access to Operator Properties x General Database Monitor Language Get wersion Set date time Get date time oP Full download ef Clear log ce O Schedule Inquiry Bsr Inputs ff Output fl Access Points E D Alarm monitoring Language
32. launch new windows e g Cardholder window Integra32 User s Manual Integra32 3 8 22r4 2 SP15 3 RBH Access Technologies Inc Chapter 2 Getting to know Integra32 Menu Options File File Options Links Tools Reporte Help amp Log Out ES Exit Use this menu to log in log out or to exit the Integra32 application aii Log In amp Out Alt L An operator must be logged in to operate the system This ensures that all actions performed on the PC can be attributed to a particular operator Connect to Server Axiemiite Integras2 Login Hame no Woe Password DEYE Default To log in enter your full login Name and password The default login name is rbh and default password is password Login Name is not case sensitive but Password is An operator should log out when leaving the computer unattended or when finished his her shift Logging out protects the system against unauthorized access 3 Exit Exit will shutdown the Integra32 System Client software Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 4 Chapter 2 Getting to know Integra32 Options File Options Links Tools Reports Help System Options C System Messages CE AP Activity Visitor Management Configuration Use this menu option to customize user preferences through System Options or customize the System Messages that are displayed on the Status Screen and in t
33. minutes the number of minutes with no activity The call back criteria are set under the Dial out tab of each panel Which events will cause the panel to call up the PC can only be set in the panels of a modem network RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 41 Chapter 5 Programming General Reader Options Site codes Alarms Code Reader Links LalUut schedule Access Granted 00 Mever Access Denied 00 Never Forced Entry foo Never Door Held Open spore Door Not Open After Hours Restore 00 Never Input Abnormal OU Never Input Restore OU Never Input Alarm OU Never Input Trouble OU Never To reset the password connect the panel directly to the Integra32 system and execute a full download to the panel Ethernet Connect The controller network 1RC 20001 URC is connected to the PC through a standard Ethernet network Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 42 Chapter 5 Programming Network Properties TCPAPNewok SS HW 125 100 75 78 300 2 For an Ethernet connection to work TCP must be installed on your computer e g IP Locator for LIF 200 Enter the specific address and proper port value for the Ethernet interface assigned to the network Enter a port value of which must match programming of Interface Advanced Time Zone Difference If a network is located in an area within a
34. readers to gain access When the count reaches zero the card can no longer be used To specify that a card is valid for unlimited number of uses enter 255 Pin Code The PIN Personal Identification Number 1s the code required at access points with a keypad Typ a There are currently only two card types to choose from Normal and Visitor Normal cards are for your regular permanent cards while Visitor cards are for a group of continually changing cards These cards are for the people who only need a card for a short period of time they use the card while they are on site and then hand it back in when they leave These are the only cards can be assigned in Visitor module Options Choose from the seven options available if required Ignore Antipassback Unlock Privilege High Security Privilege Link Execute Privilege Extended Unlock Time Disabled and Ignore Auto void Ignore Antipassback Cards that are given this option will bypass antipassback checks when presented to a reader 22 Date is displayed in the format selected under Windows Control Panel Regional Settings Properties Date If a two digit year was chosen then it will be displayed in that form here 28 Date is displayed in the format selected under Windows Control Panel Regional Settings Properties Date If a two digit year was chosen then it will be displayed in that form here 2 This selection is only available if the optional license for the Vi
35. records from cardholders which are not existing in import file anymore Option added in software version 3 8 20R4 2 and higher Click Next RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 157 Chapter 11 Tools Import Wizard Enter the path to the text File to import into the Cardholders database of Integra32 system Import From Clear C Documents and Settings Administrator Desktop Delimited By Integras Database Folder c Program Files RBH Integras Default Delete File upon successfull import Remove cards not found in import File Help Cancel lt Back Mext gt Finish Then select the appropriate destination fields for the corresponding source fields e g select Surname for Field 1 and Firstname for Field 2 depending on the data in the text file Import Wizard List Source Field Text File Destination Field 4xUserLT mdb Surname Firstname CardMurmber Firstname Initials Street Cit Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 158 Chapter 11 Tools Click Next to continue Import from a SQL file Import Wizard The wizard will help you to enter bulk data in the card holder table Cards can either be imported From an external text File or MS SOL Server Local machine should have SOL Server running or SQL Client installed Import cards From a text File f Imports Cards from SOL Server Canc
36. s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 36 RBH Access Technologies Inc Area Properties xj General Description de IN ew Area Type None Master C Slave Clear 4rea Lancel If no license for Area Type Global APB Type option will not be available in Area configuration Area Properties x General Description de Main Enterance Clear rea Chapter 5 Programming Integra32 User s Manual Integra32 3 8 22r4 2 SP15 37 Chapter 5 Programming Messages a a Messages o Call dt Add Message ds Call Police Low Remeh ogy Low Temperature TER Pony E Aa Smoke Detector k Smoke E Fas Delete gt Flood Alarm Flood Al E Properties pu Panel Trouble yf Panel Tr oe Panic Alarm a Panic Alarm Messages Instruction that operators need to follow under certain circumstances can be created and saved here xi General Message Description E Low Temperature General Under the General tab of the Message Properties Window message descriptions can be edited Message The message 1s entered under the Message tab Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 38 Chapter 5 Programming Networks Up to thirty two networks can be connected on the Integra32 system The description of each Network can be changed in the Description box under the General tab of the Network Properties Window
37. the left hand window of the Cardholder Screen when a cardholder is selected The card number and description of the card are put into this window Click the Add button to add a card to the cardholder Enter the card number in Value Name is optional and is used to distinguish a cardholder s different cards from one another Click OK to enter the card number Value 1234 Mame PO Cancel Copy will enter a new card with a different Value and an activation date of the current date All other parameters will be the same as the selected highlighted card Edit button is used to edit the description of any card assigned to the cardholder and Remove button to delete a card assigned to the cardholder RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 105 Chapter 6 Cardholders Profile Tab The profile information like address phone number and email address of a cardholder can be entered in the Profile tab All of this data is optional and does not affect the functioning of the Access Control System Integra32 AxiomLite Cardholders x File K x ith Gy New Edit Cancel Delete Search Multi Cards F Print Receipt Last name First name Initials Cardnumber ANDRULIS STEPHEN Cards Profile Photo Notes More Fields Street fi 3 Man City ABS Province ONT Country CANADA Postal Phone 51 9 666 55 Ext E mail Department fs upport lt
38. the Move All Forward and Back arrows to select sort fields Then choose Ascending or Descending for that field Click the Next button to go to next screen Click on Preview Report to see the report or click on Begin Again to view a new report or click on Finish to end The user can follow similar steps to preview or print other kinds of Database Reports as well Integra32 User s Manual Integra32 3 8 22r4 2 SP15 126 RBH Access Technologies Inc Chapter 8 Reports Visitor Reports32 Select Visitor Reports from the Reports menu to launch the following window where the user has the option of selecting from many available visitor report formats x a A E Preview Print Font DVR fe visitors Log fe Visitors activity eee 24 Apr 2007 1200 00 At fe Visitors Currently Checked In fe Wisitors Report By Department mm S visitors Report By Employer To 24 Apr 2007 11 59 59 PM F Visitors Report By Employee F visitors Report By Reason visitors Report By Cardnumber F visitors Report By Visitor E Visitors Report By Reader Choose a report format and select the Start and End Date and Time for the time period you want to preview the report for 32 This selection is only available if the optional license for the Visitor Management System has been purchased and installed RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 127 Chapter 9 Options Chapter 9 Optio
39. this button to launch the DVR module to monitor the CCTV system live Help Help Press this button to get online help 8 This selection is only available if the optional license for the Visitor Management System has been purchased and installed This selection is only available if the optional license for the DVR Interface has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 8 Chapter 2 Getting to know Integra32 Database Screen The system is configured for a particular installation from this screen Setup and programming of hardware devices RC 2000 and programming of all records such as access levels schedules and holidays are done here with the exception of cardholders Configure El Integradz System ELE Users a Holidays H D Schedules x Areas Messages E Networks E Network 1 mE Panels a Panel 1 EI Access Points Eje Inputs E Outputs Output 1 Output 2 a Output 3 8 Dutput 5 8 Dutput 6 8 Output 7 3 wo Output ce Panel 2 ce Panel 3 EH Panel 4 Er Access Levels 8 Master rbh Up to thirty two networks can be configured and up to thirty two panels can be configured for each Integra32 system These panels can be distributed across the thirty two networks as you like with no more than sixteen panels on any one network A maximum of thirty schedules each with up to eight peri
40. this time After upgrading you can come back to this screen RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 169 Chapter 12 Program Groups Clicking Start will begin the firmware upgrade Integra32 Firmware Upgrade Wizard i Upgrade status Integra32 Upgrade started to panel 1 Panel 1 1 Panel 1 Firmware upgrade completed to panel 1 Panel 1 Upgrade started to panel 4 Panel 4 A progress bar and messages will keep you informed during the process There will be a completed message after each panel upgraded You can go back to select other panels or close 1f you are finished downloading Registration The software must be registered in order to enable the Badging software the Card Import Utility the Finger Print Reader the DVR software and or the Visitor Management System None of these features will be accessible or even visible if the license hasn t been registered Only the feature ordered will be included on a license Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 170 Chapter 12 Program Groups Integra32 Registration E x For Registration Contact Your Supplier OR RBH Access Technologies Phone 905 790 1515 OR Fax 305 790 3650 OR Email customerservicemrbh access com Include the company name case sensitive to be associated with registration request Registration file path License Bi
41. under that panel will also be disabled Disabled items are still in the database but are not considered to be part of the system RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 45 Chapter 5 Programming Reader Options General Header ptions Site codes Alarms Code Reader Links Card Formats Weigand C Mag Strip C 37 bit HID Belgium C ar bit H C 39 bit Kantech SF FE Card 40 bit Farpoint C 40 bit PESE C 44 bit CAS RUSCO 50 bit REH M Interlock p y EgmII e xi Cancel Card Format This is where the card format is selected only a limited number of formats are supported list provided for both Weigand and Mag Strip formats Interlock With Interlock checked only one of the two doors on the one panel may be opened at a time If one door is open then access will not be granted at the other door until the first door is closed Site Codes Under the Site Codes tab the facility code to be used by the IRC 2000 URC 2000 is entered Each IRC 2000 URC 2000 panel will support up to ten facility site codes Leading zeros are not required when entering a site codes even though the display does show them Integra32 User s Manual Integra32 3 8 22r4 2 SP15 46 RBH Access Technologies Inc Chapter 5 Programming Panel 1 ES 04000 CET E Ses Alarms Under the Alarms tab the schedules are set for when Panel Online and Panel Offlin
42. want to display from DVR e Then enter the DVR s IP address and Port Number associated with the camera you selected as you could be using more than one DVR For this functionality to work messages need to be configured in System messages menu as explained on page 135 e The ASCII XML messages are sent to DVR 5 When lt Event gt is Output then lt Device ID gt Output ID and lt Device Name gt Output name This selection is only available if the optional license for the DVR Software has been purchased and installed RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 87 Chapter 5 Programming NOTE Integra32 server services need to be restarted whenever switching between the DVR Message Format ASCH and XML in System Options 2 The second way the interface can be used is to associate with a specific DVR DVR are set up in the Main windows toolbar under DVR AAA General Details LLTW Links OWA Name DVA 1 Camera Information History Information Camera Number W FTZ Camera Pre Event Time Post Event Time fi Miri e First select a DVR for the pull down list under DVR Name e Next configure the Camera Information Select a camera number indicate whether it s a PTZ camera or not and if it is enter a preset number if applicable e Then set the History Information Set the Pre Event Time and the Post Event Time T
43. 0 or higher RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 79 Chapter 5 Programming Access Point Activity AP Activity By checking this box you enable the automatic displaying of the Access Point Activity window for the selected event s occur at the access point Often this is used with a CCTV system for video verification of access Multiple readers may have been selected to be displayed with this window Only the last event 1s displayed though all previous displays are deleted AAA olas Grant access A Reader Number g Grant Access Grant access will grant access at the reader currently shown in the Reader box of the Access Point Activity window Note The above window is automatically displayed only if Access Point Activity AP Activity is turned on either from the Options menu or on the main screen toolbar File Options Links Tools Reports Help i System Options E cH Ea a E Lo System Messages 2 AP Activity Cards Visitors DVR Help Y M Configuration Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 80 Chapter 5 Programming Inputs E Inputs General From General tab the user can change the description of the input The Type of input is also chosen here e The input type can be General Purpose RTE for Reader A RTE for Reader B Door Contact for Reader A Door Contact for
44. 2 3 8 22r4 2 SP15 16 Chapter 3 Monitor Screen Input Points Commands Clicking the Input button on the Command Toolbar depicts the status of input points on the Device Status Screen Y o HA 5 Bi H a Reader Inputs Outputs Panels Areas Cardholders Keypads Floors Visitors Status Panel we j Input 3 Armed Normal Fanel 79 1 E Input 4 Armed Normal Panel 79 1 e a Ed Noma IE l E a nput Armed Normal Panel 79 2 ey Input 4 Disarm Armed Normal Panel 79 2 nput y Gee Armed Normal Panel 79 2 nput e e Play Armed Normal Panel 79 2 gt The following commands for Inputs are available by right clicking the selected Input s Commands Arm Input Arm the input When an input is armed an alarm is generated if the input is violated In the case of a door opening an armed door generates an alarm Disarm Input Disarm an input While an input is disarmed no alarm is generated when the input is violated In the case of a door opening the door while disarmed does not generate an alarm The system however will still generate and log a door opened event and report it to the Log Screen Live Select Live to display live video from the CCTV camera associated with the selected input point Play Play will bring up a DVR history selection screen so that video connected to an event for the chosen input point can be played back This selection is only
45. 9500 1 Jan 2038 Access Level 04 Warehouse a Card Number 39105 4dded Card Number 39106 Added Card Number 39107 Added Card Number 39108 Added Card Number 39109 Added Card Number 39110 Added Card Number 39111 Added Card Number 39112 Added Card Humber 39113 Added Card Number 39114 Added Card Number 39115 Added Card Number 39116 Added Card Number 39117 Added RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 99 Chapter 6 Cardholders Cards added through Multi Card utility do not get downloaded to panels The operator needs to do a full download to the panels to download the cards added through Multi Cards F Print Enroll Peter s Fingerprints Calibrate Calibration Parameters Default Registered Finger Salacied Fingal weied 1t Finger Delete nd Finger fed Delete ond Finger i 4th Finger i E A pp Sth Finger Quality itz Eih Finger C Secunty Level 4 Enollment completed successfully Pleaze iit your finger FingerPrint enrolment window varies for different manufactures of fingerprint readers 2 This selection is only available if the optional license for the Finger Print Reader has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 100 Chapter 6 Cardholders RBH Finger Print Enrollment O x Enroll Save 5 Cancel f USB Terminal b
46. EDO Si A A aid 149 CARDIMPORE Sa Aa tawista Mature caiadaistacanamnedneitasaa Seams daadeist alan banal A unticaateeneuntenadaeteenaaat ions 150 CONFIGURE IMPOR TU TAI Y ar A sale daadeinasan gonad A 150 TIO ESV OU TON JIC yrs heat e e a lt NL oN a ha Boa a La Dora Nat es 151 IMPOR TOMAS OLE A tt eto te leete at ea tat e DE 153 COmPpletetho COnN SUL GION ceca ie Tie e Ln td ce 133 RUN IMPORT U TILIA onone a a a a a A A 158 Intega32 User s Guide RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 il Table of Contents VIEW LOS PIB coo o tins tase Raobace dub a nace ne eebea nesta ueseseeecetantee as 159 PROGRAM GROUPS cuida lid ao io Ad ad AAA RARA LAIA AAA OA da 160 a o A A seasicase de ateanee heed 160 Integra32 Security SYSteM ccccccccccccssecessccssescscsvevevesssseveseusvsesesvsvevevesasacsenensusesesvsvavavavasacacseneusesesesvavavavavavassenens 161 Integra32 Site Configuration 161 Integra32 Data Restore ccccccccccccccscssssevsvscsesesesesvevevesssseveveusssesesvavavevasisacacueseusesvsvsvavavavasasacienensesesesvavavavavasaesenens 162 Integra32 Database Maintenance oie een 162 Integra32 Firmware Upgrade ccccccccscccscssesesescsvssssssseveseusescsesvavsvevevesacsesessusessvavavavavavasacscnsuseseseevavavavavavacaenees 162 Integra32 Registration ccccccccccccscsssssseveccssssesescsvevevsssssesesessusesesesvsvevavasaesenenensesesesvsvavavasacassenensssesestsvevavavasaesenens 164 MUESTRAS A anita 165 GLOSSARY tae ee
47. GEMEN T isccciercsdeccetnscsccevvacsetanescoaareatuasednsssseavvscsoneincseeetnssoscauencunseUuacesseuncesseadnatosaernscesaavesees eters 111 C AAA es tira eestor E TAA E AAA A A E E te 114 MOT T NS a A T A TE ST 115 AS A A LR E 116 PTAC OE 118 IS O 119 REPORTS Roatan IES ER EE E E icons 120 FOSTOR VA PORTS talar ooo orcas 120 A O A A IS A A A A A 12 TA A A O O 121 A AE E AET AAEE EA ee AAE A EE Ae E A EE AA AE Ne A EAE AAE E E AEA RNA 121 A 124 DATABASE INEPOR Sta SAA ANS snud essere nase aus 125 OOD MOMS cists E Ss aero ates a match IN 125 Y TS TT OR REPO R Sais 127 OPTIONS A A E A A ES 128 S SIENE OPTION OO a iaa 128 I IIE A O ants Alissa edi dines lad ae Ueno NERO 128 B nn OER CO APR a CREE eae ET O O O terete ee ee 130 EA A ste hci ea hed an whee oe E E ET anaes ta Mama E EAE CE A EEA EE 132 TS EE E ONE E EE EAE O TEE EE EE AE N EE E AAE A E 133 SYSTEM MESSAGES 2 A a wanGiieuseeee anc 135 ACCESS POINT AC LIVI siii E a 136 MOE CSS r sage teed hha att tees date ot st lene dase tated ds dudes 136 TDA aie O TERS ETES E EEEN EEE EEN A II EN at vetoes 137 VMC ONFIGURA TION a 138 Email CON AA a a 138 UT aaraa a a E 139 LINE Si aea O e ae E 140 GLOBAL TIN Si A A A AA A amo bacanins 140 TOOLS ceases Vases cis ed ie iioS dnooa 141 a sag eis eben sac bakes o aan tanec coasted caos 141 RUN BACON OWN dd cd dll 14 COnN EUC AUTOS A add Lis ta 142 VOIDICARDS Es 143 FINGER PRINT as A eds 144 QUERY FINGER PRINT READER onre aa 146 CARDCUSTOM P
48. History Report m Database Reports E Visitors Reports Use this menu option to customize and generate History Reports Database Reports and Visitor Reports History Reports Reports are explained later in Chapter 8 Database Reports Reports are explained later in Chapter 8 Visitors Reports Reports are explained later in Chapter 8 Help File Options Links Tools Reports Help Contents ce About Use this menu option to go to online Help by clicking on Contents or display information regarding your Integra32 software version the licensing of the software as well as dealer information by clicking on About This selection is only available if the optional license for the Visitor Management System has been purchased and installed Integra32 User s Manual Integra32 3 8 22r4 2 SP15 6 RBH Access Technologies Inc Chapter 2 Getting to know Integra32 F About Integras2 AxiomLite Security System Integras2 AxiomLite Security System Version 315 22 R42 Copyright 1995 2012 RBH Access Technologies Inc Canada Company RBH Access Technologies Inc email infot rbh access com WMA FOh access COM This Product is licensed Eo Renu s Demo Opi Options selected Card Badging Global APB by Grouping Cards Dealer Information Create a text file in the site folder e g default named rbh ini as shown below to display Dealer information in the About screen Up to nine line
49. Inc Integra32 3 8 22r4 2 SP15 94 Chapter 5 Programming Links Panel Properties i x 1 Event Select from a pull down list the triggering event Device ID Choose the appropriate device to execute the selected command from a pull down for the selected event Card Enter the card number if applicable that will trigger the selected command when it is associated with the chosen device and selected event e g execute the command when card 1234 is granted access at reader 1 Command Select the command to be executed on the chosen keypad from a pull down list Arm Keypad Disarm Keypad or Arm Perimeter Keypad Choose which keypad the command is to be executed on Pin Code Select a valid PIN code The command will be executed as though this PIN code had been entered RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 595 Chapter 5 Programming Summit The PC100 when made for the Summit application will interface the Electronics Line Gold alarm panel to the IRC2000 access control system The PC100 comes with three channels of communication all if which are programmed for a baud rate of 9600 eight data bits and no parity The PC100 passes data to and from the host to the IRC network and listens for log messages In the event where the host is disconnected the PC100 sends request for status from each panel in the network This prevents log messages fr
50. Report Areas Report Card Holders by Department Cardholder Reader Report Cardholders Report Elevator Elevator Floor Group Global Links Report Holidays Report Input Points Report Network Controllers Report Operators Report Output Points Report Reader Cardholder Report Time groups Report RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 125 Chapter 8 Reports Select one of the reports available e g Access Points Report Click the Next button to select the options available in for the chosen report Select the items to include in the report or click in the check box for Select All if you want to include all the items available in your report Click the Next button to select from the available fields to include in the report or check the Select All box to include all fields By default four fields are selected If up to five fields are selected a simple report will be produced For more than five fields a detailed report is produced For some reports there is a main report and sub report If you select Show Subreport which is selected by default the ZD field cannot be unselected It is required to link the main and sub report The fields selected in this list are for the main report only Up to ten fields can be selected If you select more than ten fields the first ten will be shown Click the Next button to select the sort order for the report Use
51. The language the system will operate in for this operator is selected in the Language tab Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 32 Holidays RBH Access Technologies Inc Operator Properties i x General Database Monitor Language Select default language English 2 Polish Danish Portuguese Canadian French Spanish Chinese Up to forty holidays can be assigned HE Holiday s k Goo 3 Add Holiday ef Good Friday ee Can A S i bes Ne v Ji Oc X delete e Labour Day Labor Fe Properties a Thanksgiving Day e Than Christmas Break ins Christmas Break Chapter 5 Programming You can edit create the name of a holiday and the date s of a holiday in the Holiday Properties You can Select a Date the holiday starts on and an End Date for the holiday Any date designated as a holiday will replace the regular day of the week for the day specified E g Good Friday 6 April 2012 as far as schedules are concerned this day will not be a Friday it will be H1 Start and end times can also be specified for the holidays In the example shown below the holiday starts on 24 December 2012 at noon Up until noon the day is Monday at noon the day becomes H1 The holiday remains until 10 00am on 27 December 2012 when the day of the week changes from H1 to Thursday Integra32_ User s Manual Integra32 3 8 22r4 2 SP15 33 Chapter 5 Progra
52. agement System has been purchased and installed RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 111 Chapter 7 Visitor Manager The Last Name and First Name fields are mandatory fields and must have data before you can save the visitor while the NationalID field is optional All three of these fields are quick search fields Type data into the quick search field and hit Enter The quick search field will call up the record with matching data or will produce a list of records to choose from Card Number 1s also a quick search field and is ideal for calling up a record when a visitor 1s checking out Add Click Add to enter a new visitor Edit Click Edit to modify an existing visitor mj Save Click Save to save changes made be adding a new visitor or modifying an existing one Pa Delete Click Delete to permanently remove a visitor from the database 7 Cancel Click Cancel to ex1t edit mode and not save any changes made dh Search Click Search to call up a search screen to look for a specific visitor Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 112 Chapter 7 Visitor Management Search Field Last Name Search Look for ance Result National ID Employer Date of Birth Select the search field enter the search criteria and click search The results of the search will be posted in the l
53. amp Warranty Notice 1 01 This Software is licensed not sold It is licensed to sublicenses including end users without either express or implied warranties of any kind on an as is basis RBH Access Technologies Inc makes no express or implied warranties to sublicenses including end users with regard to this software including merchantability fitness for any purpose or non infringement of patents copyrights or any other proprietary rights of others RBH Access Technologies Inc shall not have any liability or responsibility to sublicenses including end users for damages of any kind including special indirect or consequential damages arising out of or resulting from any program services or materials made available hereunder or the or the modification thereof Notice 1 02 RBH Access Technologies Inc makes no claim or warranty with respect to the fitness of any product or software for a specific application and assumes no responsibility for installation This warranty is in lieu of all other warranties expressed or implied No representative or agent of RBH Access Technologies Inc may make any other claims to the fitness of any product for any application RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 173 Index index A About This Guide Access Levels Access Point Activity Access Points Advanced Alarms CCTV Links Modes Time Outs Access Points Commands Acknowledge Ackn
54. and click OK The default font is MS San Serif Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 132 Chapter 9 Options Email This window is used to configure email settings for Message Server For more information on how to configure the email information see page 30 for users setup and page 73 for configuring the Access point Messages This option is added in software version 3 8 6R4 2 or higher RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 133 Chapter 9 Options Fill in the required information as per your email settings Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 134 Chapter 9 Options System Messages system Messages l x screen History Printer DWR nn A ES Mode Changed i e A We Input Y A Y Output y e A Y Audit message y y A Y Cardholder e y X e Access Requested A Ye A e Door held open warning dl a A e Door held open alarm y y A y Door not open alarm A e A e Forced entry alarm v e A e a i Enable printing DWA messages on this machine Defaults Cancel i i The user can customize how the system handles messages E g If the user doesn t want a particular message to appear on screen like the Access Requested message it can easily be turned off with a simple click Quickly change between Yes and No to stop the display of selected
55. and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 18 Chapter 3 Monitor Screen Panels Commands Clicking the Panels button on the Command Toolbar depicts the status of panels on the Device Status Screen g o gt gt a e 7 ck Reader Inputs Outputs Panels Areas Cardholders Keypads Floors Visitors B oC E E PP Vesio PA A RA n T Set datetime mE mp Fanel Online E Ma PCio 4 Get datetime esas A DownLoad ae E Cardholders Reset All Files Clear log Schedule Inquiry IRC2000 or URC2000 IN a Va en IN ae D K Feader Inputs Outputs Panels Reader Inputs Outputs Panels Description Jarima Online Panel 79 1 Online BE Panel 79 2 Online BE Panel 79 2 Online BE Panel 79 3 Online MB Panel 79 3 Online ME Panel 79 4 Online BAB ee Online Version Mali Unknown wes aa A a Teena ra Pri A Version A ee eee Set datetime Set datetime Get datetime Get date h Dl Get datetime DownLoad keppads DownLoad Inputa Links Reset moren Reset Clear log ia Clear log All Files PC100 Summit PC100 Risco Bosch or DSC IT RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 19 Chapter 3 Monitor Screen Commands IRC2000 amp URC2000 The following commands for panels are available by right clicking the selected IRC2000 and or URC2000 panel s Version The Version queries al
56. ardnumber Cardhiumber lastname Surname Firstname Firstname Falid AccessLewel expirydate ExpiryDate ll Text5 Text CardNumber La laccessLevel Status PFIN Click Next to continue Complete the configuration Select a unique key field If required check Schedule Import and select either every x hours or minutes or everyday at x RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 161 Chapter 11 Tools Import Wizard You can run the import manually or you can program it to run at a specified time Select a unique key Field Cardilumber Y Schedule Import C Every 0 Hours Everyday at an eat 1200 00 AM E Cancel lt Back IE E Finish Check the appropriate box to have the import utility start automatically with the Operating System To have all actions taken by the import utility logged check the second box Import Wizard l That is ik The import proram will run in your windows systray You can double click on it manually run it You can run this wizard any time From the import program Start import program with the 05 M Log all actions taken by the import program Help Cancel lt Back IE E Finish Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 162 Chapter 11 Tools Note the icon E in the windows system tray indicating that the utility 1s active Cli
57. at area Reset The Reset command will clear the area the cardholder is in The cardholder will not be logged into any area therefore the next card read cannot violate antipassback S Print The Print command will produce a printed report showing the data provided in the status pane It will show all of the cardholders displayed and the areas they are in RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 23 Chapter 3 Monitor Screen E 16 Visitors Clicking the Visitors button on the Command Toolbar will display the visiting cardholders and who they are visiting a a A 5 E a A El Reader Imprits Outputs Panels reas Cardholders Keypads Floors Visitors Cette Time aeai ii Device Status d Check Out Click Check Out to check out the selected visitor Floors Clicking the Floors button on the Command Toolbar depicts the status of floor outputs on the Device Status Screen Es ds MA 5 mn El a i Reader Inputs Outputs Panels Areas Cardholders Floors Visitors Refresh Status A H Cab amp Cab A Floor 1 x H Cab Cab A Floor 2 YM JE Cab A Cab A Floor 3 E lt A A ee ee a eee eee 5 Cab A A E CaA Caba M Unlock H Cab 4 Caba W Lock H Cabas Cab A Floor 8 ll ra F Cah BR Flanr 1 of Unlock Unlock will release the floor button in the cab so that allow anyone may access the floor Lock Lock will energize the floor output and disconnect the floor button in the
58. cab A card with the appropriate access level can release the floor temporarily This selection is only available if the optional license for the Visitor Management System has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 24 Chapter 3 Monitor Screen Keypad Commands If you have installed a PC100 for Bosch Summit or DSC you will have a Keypads icon on the Status button bar Click on this icon to bring up the list of respective keypads Depending upon the type of PC 100 the right click menu on list of Keypad will vary g ee E O m MA Reader Inputs Outputs Panels Areas Cardholders Keypads Floors EXT Description RS E E eee ee ee er cere ee O ar o we Disarm o E Status a A al l el Commands user Y Select the name of the PIN code that the command is to be issued by Arm Keypad Arm the selected keypad with the selected PIN code Disarm Keypad Disarm the selected keypad with the selected PIN code Status Depending upon the type of PC 100 the status screen will vary for the keypad RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 25 Chapter 3 Monitor Screen LED keypad status will be displayed in this window Arm amp disarm commands can also be issued from here Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 26 Chapter 4 Alarm Screen Chap
59. cards granted access if the cards usage count is less than 255 Card with a usage count of zero will not be granted access Usage count works per panel if the system is run offline Systems that are run online will have the usage count of a cardholder updated in all panels when any reader reduces that cardholder s count Disable Forced Entry If Forced Entry is disabled then opening the door without an access granted will not cause a Forced Entry alarm but instead will start the access granted sequence This is generally used on a door with a mechanical egress and no request to exit device First Person Delay Access points with lock unlock schedules will lock and unlock according to the schedule If First Person Delay is selected the door will remain locked until the first card is granted access after the start of the schedule RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 69 Chapter 5 Programming RTE Bypass DC This feature 1s used with the doors having mechanical egress The Request to Exit device will bypass the door contact but will not unlock the door The door can be opened without causing an alarm since the contact 1s bypassed PC Decision Required Selecting PC Decision Required takes the decision to grant access away from the panel If the panel would normally grant access it wouldn t Instead it simply sends a message to the PC Access Requested An operator at the PC can the
60. ck Finish to complete the setup The utility can then run on a schedule or can be opened to run manually RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 163 Chapter 11 Tools Run Import Utility Run Import Utility will run the utility immediately 210 xi Integra32 Card Import Utility Click to Run the configured Card import now dd Run Import utility 44 Config Import utility view Log File The status bar will display the progress and indicate when the import is complete Card Import Utility JO xj Integra32 Card Import Utility Click to Run the configured Card import now dd Run Import utility 44 Config Import utility View Log File Import Completed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 164 Chapter 11 Tools View Log File Card Import Utility Integra32 Card Import Utility Click to see the log File to see any errors created by card import Run Import utility Config Import utility view Log File View Log File will call up Mimport log a Notepad file This file will show when the import started and ended as well as any errors that occurred 8 Mimport log Notepad l lOj x File Edit Format Help 31 Aug 006 09 17 Integra Import started 31 Aug 006 9 17 01 AM 31 Aug 006 09 17 Integra Import Completed 31 Aug 2006 9 17 02 AM RBH Access Technologies Inc In
61. d keypads to affect the Risco Group system Only five of the possible two hundred PIN codes may be entered here Pin Code Name Enter here a description or name for each PIN code RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 61 Chapter 5 Programming Links Panel Properties x 1 coo Ao Event Select from a pull down list the triggering event Device ID Choose the appropriate device to execute the selected command from a pull down for the selected event Card Enter the card number if applicable that will trigger the selected command when it 1s associated with the chosen device and selected event e g execute the command when card 1234 is granted access at reader 1 Command Select the command to be executed on the chosen keypad from a pull down list Arm Keypad Disarm Keypad or Arm Perimeter Keypad Choose which keypad the command is to be executed on Pin Code Select a valid PIN code The command will be executed as though this PIN code had been entered Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 62 Chapter 5 Programming DSC IT 100 This PC100 interface uses the DSC IT100 to allow communications between the Integra Access Control System and the DSC Power Series Burglar Alarm panel The PC100 is programmed through the Integra32 Software Version 3 7 18 or higher and is designed t
62. d umber 454349 Candy umber CardHolderFirst ame lt LardH olderFirst ame gt lt CardHolderLasth amet lt CardHolderLasth ames lt Event gt Access granted E vents lt EventT est ccezsz granted Card Event ext lt DevicelD gt 16043265 lt DevicelD gt Device ames Reader 78 2 12 DeviceN ame Panell gt b5 94 lt PanellD PanelN ame Panel 18 4 lt Panel ame eD atas lt r mag version 1 gt lt DateTimell TCs 7 5 2072 6 55 29 Pher DateTime T C lt D ata lt Camerah umber E Camera umber lt Card umber 4543949 Cand umber lt CardHolderFirst ames lt CardH olderFirsth ame gt lt CardHolderLasth amet lt CardHolderLasth ame lt E vent Access granted Events lt EventT ext ccess granted Lard lt Event ext lt DevicelD gt 160432b65 lt Devicell gt lt DeviceN ame Reader 78 2 lt Device ame lt Panell gt 65 94 lt PanellD gt lt PanelN ame Panel 18 4 lt PanelN ame lt D atas lt meg gt This applications listens on port 3300 XML format string is lt msg Version 1 gt lt DateTimeUTC gt lt DateTimeUTC gt lt Data gt lt CameraNumber gt lt CameraNumber gt lt CardNumber gt lt Card Number gt lt CardHolderFirstName gt lt CardHolderFirstName gt lt CardHolderLastName gt lt CardHolderLastN ame gt lt Event gt lt Event gt lt EventText gt lt EventText gt lt DeviceID gt lt DeviceID gt lt DeviceName gt lt DeviceNa me gt lt PanellD gt lt PanellD gt lt PanelName gt lt Pan
63. d when the system was installed or you can click on Integra32 Security System in program groups Both methods will start Integra32 system Integra32 Add Remove Site Add Site xj pi ARNANAA MAA AAA NENE MEN cee Site Mame ii asc Manufacturing Corp Add Site Remove Site RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 167 Chapter 12 Program Groups Type in the name of the site and either click Add Site or Remove Site Sites added will be selectable on the server pull down list while logging on Each site will have its own database and maintains its own backup you must be logged on to the site at the appropriate time for the auto backup for that site to run Integra32 Data Restore To restore backed up files click on Integra32 Data Restore in program groups Integra32 Data Restore Select source folder de Y C Program Files br lntegrase 7 est Backup bRPZU0S50s3 El Select the file s to restore y AxuserLT mdb fan AsaystLT mdb Cancel Back Henst gt Finteh The Data Restore Screen allows you to select which files are to be restored Image files and Purged files AHB mdb cannot be restored through this Restore module To restore those files copy them from the backup folder Integra32 Database Maintenance Running Database Maintenance will compact and repair the Integra32 databases The Repair will
64. de on or off for an access point and turning Disable Forced Entry on or off Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 72 Chapter 5 Programming After you have selected a command an appropriate device needs to be selected input output or access point Choose the duration of the command 0 127 seconds or 0 126 minutes Not all commands can be timed High Security on and off and Disable Forced Entry on and off cannot be timed A schedule can also be selected for each command the command will only be executed when the schedule is on The example above has the Output 3 being turned on for five seconds and Disarm Input 7 when there is a forced entry at Reader 1 but only during the specified schedule associated with output input Alarms Reader 1test email E xX General Modes Time outs Links Alarms COTY Advanced Access Granted Ale atada Instructions Access Denied J Door Held Open o Always Door Not Open Forced Entry Restore Show Video If camera assigned on DWA tab Access Granted ATE Show Video on Event E mall Addrese U perator oos Test operator Send Email on Alarm Send Email on Event First select an event from list on the left The alarm will occur when the message appears in the log screen Then select an Alarm Schedule Causes an alarm when Then you can select if required an instruction message fo
65. description simply type over it Panel Type The panel type is chosen when the new panel is added and cannot be edited later Enable If the enable check box is not checked then the panel will not be shown in the status screen All Access Point Inputs and Outputs under that panel will also be disabled Disabled items are still in the database but are not considered to be part of the system Inputs The inputs of a Summit panel can be affected by the events from Integra32 access panels They can follow the access panel s inputs by mimicking them going into alarm when the access panel s input goes into alarm Alternatively they can arm disarm the Summit panel when access is granted at a reader the Summit panel s input must be set as an arm disarm input On the other hand they can follow an output on the access panel as if the output was wired to the input Input 10 Print Lancel Apply Zone There are 32 zones RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 9 Chapter 5 Programming Description The zone name or description can be edited here Panel Designate which panel the input will be affected by Command Choose the function for the input from the pull down list Does it follow an input or an output or is it used to arm or disarm the Summit panel Output If the input follows an output designates which output from the pull down list Risco Group
66. different time zone you can set the difference here Set the number of hours either ahead or behind of the time where the server 1s located RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 43 Chapter 5 Programming Network Properties x Time Zone Difference joo 00 HH MM C Backward ff Forward Panels Up to thirty two panels in total can be connected to the Integra32 system Add Panel d oe El Add Panel IRC2000 Access Les ddd PC100 e UWRE2000 la Refresh UIRC2000 E levator He Inputs H S Outputs ME Panels Panel 1 EN Au 2 Delete MEG Ing Fs Properties HEE ou H Fanel 3 Panel 4 1 Number of panels installed can go up to 128 license required Bosch DSC Summit Rico Group Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 44 Chapter 5 Programming IRC2000 or URC2000 General Address Description Panel Fanel type IRC2000 e Enabled Cancel Address The address is selected at the time of creation and cannot be edited later Description To change the default description simply type over it Panel Type The panel type is chosen when the new panel is added and cannot be edited later Enable If the enable check box is not checked then the panel will not be shown in the status screen All Access Point Inputs and Outputs
67. e 4 H System Status Clicking on the System Status button on the toolbar of the main screen will change the Alarm Screen to the Monitor Screen or the System Status Pane From the System Status Pane the operator can lock and unlock doors arm and disarm inputs and switch on and off outputs The status is displayed in real time but only for those devices that have reporting enabled The operator can turn messages off for certain events and no history will be logged for those events but the status of devices will not be affected The first six buttons will bring up Access Points Inputs Outputs Panels Areas and Cardholders respectively Floors Keypads and Visitor buttons will be available 1f have those options configured The Status of the selected items can be shown either in List View or Report View The next button Refresh is used to update verify the status of the items shown Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 12 Chapter 3 Monitor Screen How to Execute a Command All operator commands are executed in the same manner 1 Click on the appropriate button on the System Status Window toolbar to load the desired devices 2 From the list of items Input Output or Access Point etc select the item s you want to control Clicking on the first item then holding down the Shift key and clicking on the last item in the range can choose a group of items Select non sequ
68. e cause an alarm An instruction message can be assigned to these alarms as well from this tab Instruction messages are created elsewhere RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 47 Chapter 5 Programming Panel ee xi General Reader Options Site codes Alarms Code Reader Links Panel Offline ANA ANNAN Alarm chedule 00 Never Instructions y Code Reader Links Code reader links can be linked to one or multiple inputs outputs and access points on a local basis A single access code with a card read is capable of invoking different links dependent on which access point it is presented at This linking is done at the controller level without the Host PC online A combination card reader and keypad is needed to utilize this function The programmed link is executed for the appropriate key code after a grant access has been executed at the specified access point In the example below Code Reader Link 1 High Security Mode off for both Reader 1 amp Reader 2 at specified schedules will be executed after a grant access and a key code entry of 1234 on the side A reader of Panel 1 Code reader links are used primarily in HVAC control lighting control and intrusion alarm control systems where it is necessary to control inputs outputs and other access points from a single card read With code reader links the same cardholder can perform diffe
69. e panel will not be shown in the status screen All Access Point Inputs and Outputs under that panel will also be disabled Disabled items are still in the database but are not considered to be part of the system Keypads Panel Properties Pririt Cancel Apply Address This is the address of the keypad in the Bosch system 1 15 Only five of the possible fifteen keypads can be selected for use with the PC100 Name Enter here a description or name of the keypad to be shown in the Integra32 system Emulated Check this box if the Integra32 system will be emulating this keypad and leave it unchecked to monitor an existing keypad Signals from an emulated keypad will be the same as signals from an existing keypad therefore to the Bosch system there is no difference between an emulated keypad and an existing keypad RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 93 Chapter 5 Programming Pin Codes Panel Properties Select either 4 Digit Pin Codes Or 6 Digit Pin Codes Pin Codes Enter the four or six digits of each PIN code These PIN codes must match PIN codes programmed into the Bosch system in order for commands from the emulated keypads to affect the Bosch system Only five of the possible two hundred PIN codes may be entered here Pin Code Name Enter here a description or name for each PIN code Integra32 User s Manual RBH Access Technologies
70. el lt Back Mesck gt Finish Click New to input the connection string Import Wizard l Connection String Test Connection Table Query Integra Folder Help RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 159 Chapter 11 Tools Use the pull down to select the server Enter the User Id and password Then select the specific database on the server that holds the source data Click OK im Build Connection String xj Provider SQLOLEDB Server TESTIMGSERYER ed Trusted Connection User Id sa Password password Database Axiombiata bl OK Cancel You can verify the connection with Test Connection Select the table or query of the database set above and then provide the path to the target folder by either typing or browsing Import Wizard Connection String provider SQLOLEDE iserver TESTINGSERYER database Test Connection Mew Table Query Card_Import le Integra Folder c Program Files rbhIntegras Default Blank Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 160 Chapter 11 Tools Then select the appropriate destination fields for the corresponding source fields e g select Surname for lastname and Firstname for firstname depending on the data provided by the table or query Import Wizard i List Source Field Text File Destination Field 4xUserLT mdb c
71. elName gt lt Data gt lt msg gt 5 When lt Event gt is Access Granted Access Denied or Access point then lt Device ID gt Reader ID and lt Device Name gt Reader name Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 76 Chapter 5 Programming NOTE Integra32 server services need to be restarted whenever switching between the DVR Message Format ASCH and XML in System Options 2 The second way the interface can be used is to associate with a specific DVR DVR are set up in the Main window s toolbar under DVR x General Modes Time outs Links Alarms CCTV Advanced DVA Name None Camera Information History Information Camera Mumber CS PTZ Camera Pre Event Time Post Event Time i e First select a DVR for the pull down list under DVR Name e Next configure the Camera Information Select a camera number indicate whether it s a PTZ camera or not and if it is enter a preset number if applicable e Then set the History Information Set the Pre Event Time and the Post Event Time These times set playback start time how much time before the event time and the playback end time how long to continue the playback after the event time This configuration is used by the History Reports DVR tab to playback video associated with a logged event RBH Access Technologies Inc Integra32 User s Manual Integra32
72. en ahaa radiad piensa one clades AEO PANELS COMMANDS eiie ad Commands IRC2000 amp URC2000 ooococnccnnccnnnccnnncnnncnnnncnnncnnnrnnorononcnnnccnnns Commands PCIOO SUMMIEL diodes Commands PCI00 Bosch Risco DSC ooooooonnnnnnnnnnnnnnnnnnnnnnnnnnononnnnninnnoss AREA AND CARDHOLDER COMMANDS occoccccooccnnnccnonccnonccnnnncnnnnccnonccnanacnnnnonnns COMUNAS IAE ALEA A Ad VISITORS a seee e del y eo ind a eg aay AS PICOOR S lla acia KEYPAD COMMANDS is COMMON GS iii ds ad AVARVESCREEN cacon ACKNOWLEDGE UNACKNOWLEDGE CLEAR ccccecceccecceccecceeceeccecceccescascascs ACARMIDE TAVIS set eee li onan ae TT OU OAS assure en Coase thea Tate ns et Oeste te et Phat eel ed athe geek DON CO CS a eset det A ty tent ee epee tO ere i ed MESS TO E a ec TS AAA II A estan Dect AAA A RR E A atau UDUS AAA Pe A eee elces VEY LL OMS A A O OEE AE E E yaaa E E T ona FOOF GVOUDS sl ACCESS E A CIS RES IEAS EAN EA NES EEA AS data RBH Access Technologies Inc Table of Contents Intega32 User s Manual Integra32 3 8 22r4 2 SP15 Table of Contents CARDHOLDERS adi iaa 96 FIELDS AND OPTIONS coi a 97 AD A a AA A A 98 L E IN A A AN Pee T E A N N ear meen mere Ete 100 A OE E A TT AO AT EAN 101 CARD HOU DE Rol DB aaa a E E E AN 103 AAA IS a a A IRE en ete 103 ASA A N A ON Trea Deere 106 POO T e a ee at A N dd 107 INES aisla ao aca iaa A 108 WORST ELL T A rro cria eee Mme ee et re one Fee A Free net nt ere Hiren ratte a staraia dae 109 VISITOR MANA
73. ential item groups by holding down the Ctrl key and clicking on each desired item Set the command type to permanent semi permanent or timed 4 Right click on the Item s highlighted and then choose a command from the list provided 99 The command is then immediately sent to the appropriate IRC 2000 controller s and or URC 2000 controller s for execution Command Type Permanent From the drop down menu select one of the three options available for command type Permanent commands are used to perform actions and to manually override system operation When the status of an input output or access point is changed by a permanent command the scheduler no longer controls the device For example if a door 1s normally armed from 6 00 p m to 8 00 a m by the scheduler and a permanent command is issued to arm the door the door will remain armed forever and will not be disarmed by the scheduler A permanent command remains in effect until cleared by a second operator command or fresh files are downloaded to the controller Semi Permanent Semi permanent commands are executed like permanent commands but do not override operation of the scheduler In the above example of the door armed by scheduler between 6 00 p m and 8 00 a m if a semi permanent command is issued at 4 00 p m to arm the door the command is executed The scheduled operation remains unaffected and on the next day at 8 00 a m the door will disarm and reve
74. ess Technologies Inc reserves the right to revise this publication and to make changes to the content hereof from time to time without the obligation of RBH Access Technologies Inc to notify any person or organization of such revision or changes RBH ACCESS TECHNOLOGIES INC 2 Automatic Road Suite 108 Brampton Ontario CANADA L6S 6K8 Tel 905 790 1515 Fax 905 790 3680 Email support rbh access com Web www rbh access com Printing Date January 17 2013 Integra32 Revision 4 2 Intega32 User s Guide RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 Table of Contents INTRODUCING INTEGRA32 ccccsscosceccsccecceccsscscssscscceccsscsececcsacsacsacsacees INTEGRA32 SERVER CLIENT NETWORK SETUDP ccccececcscecececscccecececesecs GETTING TO KNOW INTEGRA 2 wiccccccscsssscsssscsecssscsecscsssessssssecssseserecees COMMAND DAR e e cos ieee E Meni ODL ONS dd ies Toolbar BuO cz eects cael ae Sec aati Se tie ae Sects ees Sue as DATABASE SCREEN aaa SE EPI EI 2 ESE AE EA E AT ET AAR Na A T OA AOR EVEN LOGO CREEN ee e tee cena aataeaeeeeinets MONITOR S CREEN 2 E N SYSTEM STATUS ia tcadia HOW TO EXECUTE A COMMAND id it COMMAND ERE sitos ACCESS POINTS COMMANDS a iaa OO LEC Oe ee TEIN O E E AY Bet Wate OnE INPUT OIN TS COMMANDS3uair aan CO LLL Oe ET TIRE AE IA Pn PAE SRR OTT SITIO A RTT want one OUTPUT POINTS COMMAND ccsssscccsssccssscecescscnscccucscuessceesscscnscscucsenecscs CONGO RAR E ad
75. gra32 time group schedules are not appropriate Statutory holidays and summer shut down periods are two examples In Integra32 Holidays may be assigned special irregular time group schedules that override the regular time group schedule for that day Any field apparatus that provides information to an Integra32 system with respect to conditions or status of a monitored component Examples include door contacts thermometers etc Operator Any individual authorized to log on to the Integra32 system for purposes of data entry or monitoring Personal Identification Number Request to exit RTE TAPI Telephony Application Programming Interface TAPI is a Microsoft Windows set of functions that allows programming of telephone line based devices in a device independent manner giving personal telephony to users TCP IP Transfer Control Protocol Internet Protocol TCP IP is the protocol that networks use to communicate with each other on the Internet Time Group A Time Group e g Business Hours is a pre defined time slot day combination that may be assigned to schedules thereby governing how the Integra32 system operates from day to day Any field apparatus that receives commands from an Integra32 system and executes the action specified in the command Examples include door locks and lights Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 172 License Warranty License
76. he History Reports The Access Point Activity window is also enabled here Details of the AP Activity window option will be discussed in Chapter 9 Visitor Management configuration is accessed by selecting Visitor Management Configuration Links File Options Links Tools Reporte Help ad Global Links This is where Global Links are setup details of this are shown in Chapter 10 Tools File Options Links Tools Reports Help E Backup Es Void Cards Finger Print i Query Finger Print Reader b Badge Template Designer Card Custom Fields E Card Import The Tools menu gives the options for Backup Void Cards Finger Print Query Finger Print Reader Badge Template Designer Card Custom Fields and Card Import which are covered in more detail in Chapter 11 This selection is only available if the optional license for the Visitor Management System has been purchased and installed This selection is only available if the optional license for the Finger Print Reader has been purchased and installed gt This selection is only available if the optional license for the Badging Software has been purchased and installed This selection is only available if the optional license for the Card Import Utility has been purchased and installed RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 5 Chapter 2 Getting to know Integra32 Reports File Options Links Tools Reports Help BB
77. hese times set playback start time how much time before the event time and the playback end time how long to continue the playback after the event time This configuration is used by the History Reports DVR tab to playback video associated with a logged event L The Links tab is only available for programming for general purpose outputs Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 88 Chapter 5 Programming Links AAA Select an event Output Off Command Device Duration Schedule a 3 y E Lancel e First select an event Either Output On or Output Off e Then select up to eight commands to be executed with that event The command selection list includes arming or disarming an input turning on or off an output locking or unlocking an access point setting High Security mode on or off for an access point and turning Disable Forced Entry on or off e After you have selected a command an appropriate device needs to be selected input output or access point e Choose the duration of the command 0 127 seconds or 0 126 minutes Not all commands can be timed High Security on and off and Disable Forced Entry on and off cannot be timed A schedule can also be selected for each command the command will only be executed when the schedule is on RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15
78. integra32 Integrated Alarm Monitoring and Access Control USER MANUAL new generation building security Copyright Notice Copyright 1995 2012 by RBH Access Technologies Inc All rights reserved Worldwide Printed in Canada This publication has been provided pursuant to an agreement containing restrictions on its use No part of this book may be copied or distributed transmitted stored in a retrieval system or translated into any human or computer language in any form or by any means electronic mechanical magnetic manual or otherwise or disclosed to third parties without the express written consent of RBH Access Technologies Inc Brampton Ontario Canada Trademark Integra32 is the trademark of RBH Access Technologies Inc Windows is a trademark of Microsoft Corporation All other product names mentioned herein are the property of their respective owners Use of a term in this book should not be regarded as affecting the validity of any trademark or service mark Disclaimer This book is provided as is without warranty of any kind either express or implied including but not limited to performance merchantability or fitness for any particular purpose Neither RBH Access Technologies Inc nor its dealers or distributors shall be liable to any person or entity with respect to any liability loss nor damage caused or alleged to have been caused directly or indirectly by this information Further RBH Acc
79. ions Links Tools Reports Help a gq Status AP Activity Configure E Pe ES Ey gt gt Reader Inputs Outputs Panels Areas Cardholders a Status Status Pane E Log Out Cards Visitors EA E OWA Help Alarms E Integrada System E EE Users qe 2 bh R 2 bhr on e agent 2 admin 2 Guest Database Pane Device Status ratorb O Schedules 1 Areas 471672012 11 02 57 Audit message Operator logged on rbh ce Messages 4 16 2012 11 03 29 System Panel offline Panel 79 1 Se Networks 471672012 11 03 36 System Panel offline Panel 79 2 Fla Network 76 Wi 471672012 11 03 44 System Panel offline Panel 79 3 BE Panels 4 16 2012 11 03 52 System Panel offline Panel 79 4 fl fa Panel 79 1 E f A Panel 79 2 gt a Panel 79 3 A m Panel 79 4 A Access Levels Event Log Pane rbh Site Default Alarms 12 Acknowledged 0 416 2012 11 06 AM 2 Command Bar Menus and buttons to access other features of the system are available on the Command Bar Integra32 has the following menu options Fil Options Links Tools Reporte Help Each of these items has a drop down menu with further options that launch the functions contained in the drop down menu e g Log Out of the Integra32 system In addition Integra32 provides Toolbar buttons as an optional means of launching either the same function contained in drop down menu or to
80. ir Card name Kanty Riarh Card number 454345 Vertication mode Finger o Maximum fingers per card 1 Fingers captured U Select a finger and click Enroll to start enrolling finger Fail to initialize the enrolment unit Receipt Receipt will create a printable document for the cardholder to sign indicating that the cardholder has taken possession of the card RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 101 Chapter 6 Cardholders Receipt AnS 201 2 4ls 15PM1 Card Name STEPHEN ANDRULIS Card Number 440068 Department support User Number 0 User Number ll User Text 1 User Text 2 Access Level Master I have received the above card and accept that I have to report it immediately 1f it is lost The card is personal and never to be handed to anybody else Signature Card Name STEPHEN ANDRULIS Date 412012 Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 102 Chapter 6 Cardholders Cardholders Tabs Cards L Since cardholders can have multiple cards card features will only be shown for selected highlighted card number only When adding or editing cards ensure that the proper card number is selected highlighted Integra32 AxiomLite Cardholders x File ya El KD A EN Ta Us Mery Save Cancel Delete Search Multi ards F Print Receipt Last name First name Initials Cardnumber ANDRULIS
81. ited here Keypad Select the Keypad assigned to various zones from the drop down menu RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 67 Chapter 5 Programming Access Points Access Points General Description To change the default description simply type over it Input amp Output Configuration This section of the tab tells you which inputs and outputs are assigned to the access point Enable If the enable check box is not checked then the access point will not be shown in the status screen and will not be considered as part of the system Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 68 Chapter 5 Programming Modes x General Modes Time outs Links Alarms CCT Advanced Options M Auto relock High security Deduct usage Facility code mode Digable forced entry e Report ATE First person delay Report door not open ATE Bypass OC e Report unknown format PC Decision Required Inhibit 1D Unlock schedule foo Hever Card PIN schedule foo Hever Auto Relock After a grant access the door locks again at the end of the unlock time With auto relock checked 1f the door closes before the unlock time expires then the door will lock when the door closes and won t wait until the timer expires Deduct Usage Readers selected to deduct usage will reduce the usage count of
82. l Change the Description select a reader and for that reader determine which outputs floors are to be controlled on this elevator You can create up to two elevators per controller by using both the A side and B side readers Integra32 User s Manual Integra32 3 8 22r4 2 SP15 91 RBH Access Technologies Inc Chapter 5 Programming Floor Groups A M caba p E Elevator Floor Groups E Properties Add Floor Groups as required Change the description and select which floors are to be member of the group Each group can be given an Unlock Schedule so that 1ts floors can have free access during that time Maximum 15 floor groups can be added per elevator im Elevator Floor Groups xi Elevator Floor Groups Description Lab 2rd 4th th amp 8th Floors Elevator Cab A Unlock Schedule o Always Available Items Description Tt Floor Cab 4 31d Floor Cab 4 Bth Floor Cab 4 bth Floor Cab 4 Sth Floor Cab 4 Selected tems Description end Floor Cab 4 4th Floor Cab 4 tth Floor Cab 4 oth Floor Cab 4 10th Floor Cab A 11th Floor Cab A 12th Floor Cab A Cancel Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 92 Chapter 5 Programming Access Levels E M Access Levels Assigning schedules to access points and floor groups creates access levels They are created so that cardholders can be easily given acces
83. l be shown by default Click the Cardholder by Number or Cardholder by Name to select cardholders for your report All cardholders are selected by default The user can customize the report by clicking in the checkboxes for Access Denied Access Granted and Cardholder Action These selections will determine which messages are to be reported on Click the Preview button to preview the customized cardholder s report Radio buttons Select one of Entry Reader Exit Reader or Both Readers are exit readers if they are connected to the Out Reader side of an Exit Reader Module or if their TAM terminal is grounded IRC2000 4 boards only Otherwise they are entry readers this includes all readers on IRC2000 3 2 boards Entry reader Exit reader Both Integra32 User s Manual Integra32 3 8 22r4 2 SP15 122 RBH Access Technologies Inc Chapter 8 Reports 10 x x amp amp Fite 00 y 14 1 of gt ro eh ese Preview 4 Apr 2006 Date 5 May 2006 Time 2 17 185 M1 Integra32 Cardhol Date Message Location 24 Apr 2006 74S 00arn Mode charnged Urdock pending first person by schedule Access granted Card Access granted Card Feader 1 Panel 1 10 41 44am 10 43 arm Reader 13 Panel 7 Reader 13 Panel 7 10 47 bare 10 48 O3arn 10 48 53arn 10 49 Tarn 10 54 3arn 10 54 32arn 10 55 2arn 10 55 40arn 10 55 54arn 10 44 Wee Access granted Card Access gran
84. l or selected IRC 2000 and or URC2000 for the firmware version they are running The version number will be displayed on the Log Screen Set Date Time Click on the Set Date Time to launch the Set Panel Date Time Screen e The Get Local button is used to retrieve the current date and time settings from the PC s internal clock e The Set button is used to upload the selected Date Time settings to the selected IRC 2000 and URC2000 controllers e The Close button is used to close the Set Panel Date Time Window Get Date Time This command queries the controller for its current date and time and displays it on the Log Screen Download The Download function allows the operator to manually repopulate the IRC 2000 and or URC2000 memory from the database on the server Select any of the listed files to download or select the AlI Files option to download all files Download messages are posted to the log as files are sent verifying the number of records sent in each file Card records are sent individually and will indicate the card number and whether it was added or deleted Edited cards are displayed as added If the panel is offline at the time of the download the files that failed to download will be logged on the Log Screen Panel download does not execute itself after the panel comes back online have manually re start the download on that panel Reset The Reset option initializes the panel Clear Log The Clear Log op
85. le If the panel is offline at the time of the download any files that fail to download will be logged on the Log Screen Panel download does not execute itself after the panel comes back online have manually re start the download on that panel Commands PC100 Bosch Risco DSC The following commands for panels are available by right clicking the selected PC100 Bosch Risco DSC panel RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 21 Chapter 3 Monitor Screen Version The Version queries the selected PC100 for the firmware version it is running The version number will be displayed on the Log Screen Set Date Time Click on the Set Date Time to launch the Set Panel Date Time Screen e The Get Local button is used to retrieve the current date and time settings from the PC s internal clock e The Set button is used to upload the selected Date Time settings to the selected PC 100 e The Close button is used to close the Set Panel Date Time Window Get Date Time This command queries the PC100 for its current date and time and displays it on the Log Screen Download The Download function allows the operator to manually repopulate the PC100 memory from the database on the server Select any of the listed files to download or select the All Files option to download all files Download messages are posted to the log as files are sent verifying the number of records sent in
86. ligent Field Panel also has eight fully supervised alarm inputs along with eight outputs The IRC2000 s memory has been increased to now hold 5 000 card and can be further extended to hold 8 000 cards An alternate panel the URC2000 can be used along with or instead of the original IRC2000 This panel also uses fully distributed intelligence for off line operations In addition to supporting two card readers each URC 2000 panel has four fully supervised alarm inputs and four outputs as well as a 3 000 card capacity Communication is handle through an RS485 port Integra32 Server Client Network Setup Please see technical document TB63 for a step by step guide to installing Integra32 Z po In order for a remote client to connect to the server the server must first be running This should not be a problem since the Integra32 server now runs as a service and should be running at all times Must have at least service pack 4 installed Must have a t least service pack 2 installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 2 Chapter 2 Getting to know Integra32 Chapter 2 Getting to Know Integra32 Integra32 lets you manage and monitor all your security access needs using a standard PC There are four separate parts to the Integra32 s main screen 5 x i Integra32 AxiomLite Security System SALES DEMO Command Bar File Opt
87. logies Inc Integra32 3 8 22r4 2 SP15 10 Chapter 2 Getting to know Integra32 Event Log Screen This screen displays all system activity such as cardholder activity input activity output activity and panel activity All system messages are also displayed here 3 May 2006 08 32 39 Audit message Operator logged on 3 May 2006 08 39 06 Audit message Record changed Access Point Reader 1 3 May 2006 08 39 22 Audit message Record changed Access Point Reader 6 3 May 2006 08 39 10 Access point Forced entry alarm Reader 1 Panel 1 3 May 2006 08 38 36 Access point Forced entry alarm Reader 6 Panel 3 All the messages shown here are also saved to History and can be retrieved through History Reports RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 11 Chapter 3 Monitor Screen Chapter 3 Monitor Screen From the Monitor Screen or the Device Status Pane the operator can issue commands as well as view status Commands can be sent to access points inputs outputs and panels Areas can be cleared and cardholders can have their area set or cleared a D l gt iW MA E E Sembpermanent ACCESS Inputs Outputs Panels reas Cardholders B B 5 Reader 1 Unlocked Normal E Reader 2 Locked Normal a Reader 3 Locked Normal E gi Reader 4 Locked DHO Warning E E Reader 5 Locked Normal lA Reader 6 Locked Normal A Reader 7 Locked Normal A Reader 8 Locked Normal a
88. messages on the screen or from being sent to history The user can also send messages to a printer selectable by message Messages can also be sent as ASCII XML messages to DVR CCTV configuration will be required for this to function correctly The user can also select what messages to send as ASCH XML messages by simply changing between Yes and No for DVR messages Check the box Enable printing DVR messages on this machine if the DVR is configured to send ASCIAXML messages or the printer is on the local machine RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 135 Chapter 9 Options AP Activity apactvty olx Grant access Reader Reader 14 Number 38093 Date 30M ar 006 11 40 53 Event Access Granted Mame Melisa Demara She usually wear contact lenses although occationally she mear Glasses The AP Activity feature can be used with a CCTV system for video verification To do this enable PC Decision in the Modes tab of the Access Point s Properties window and check AP Activity Access Requested in the Advanced tab of the Access point s properties window Now whenever a valid card is read at the access point the AP Activity window will open displaying the cardholder s picture name and card number the date time of the event and at which reader the event happened If PC Decision is not used in the Modes tab then the AP Activit
89. mming Holiday Properties l x Haliday Description pa Christmas Break Start Date 12242012 12 00 00 Ph End Date 1242742012 10 00 00 49 Cancel Schedules Before cardholders are entered any additional Time Groups that are required should be programmed Up to thirty two schedules can be programmed for Integra32 system aE Schedules EEO Schedules eC CO Add Schedule oo Never re pl m eE _ 9 pe al E Mon Delete E After Hours 3 nD after Fes i General Change the Description of the Schedule under the General tab of the Schedule Properties Window Time Zones Program the Time Zones for the New Schedule in the Time Zones tab of the Schedule Properties Window Integra32 User s Manual Integra32 3 8 22r4 2 SP15 34 RBH Access Technologies Inc Chapter 5 Programming Schedule Properties x General Time ones Start End Sun Mon Tue Wed Thu Fro Sat H1 Periodi ooo oroo Y Y Y Y YA pened for fren YA Aid paa mo Tm AAA A point oxo for Pernod 5 Period 7 Jel T Period 6 oggi 0000 Lancel e Fight time periods can be programmed Click to check or uncheck a day for the period End time must be later than start time Valid times are from 00 00 to 24 00 even though 24 00 is never actually reached it represents the end of the day Schedules that cross midnight will requi
90. n esaLes DEMO T Integra32 Data Folder C Program Files kbhiIntegra3z2 Default Ne Company Mame ISALES DEMO UnRegister To register the software input the following three pieces of information 1 Browse for and enter the path to the folder holding the license file license bin 2 Browse for and entry the path to the site folder to be registered Each site 1s registered separately if you have multiple sites 3 Enter you company or site name Then click Register Integra32 Server With this option you can Start Stop and or restart Integra 32 Server services RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 171 Glossary Glossary Many of the words or terms in this guide have more common definitions than used in industry In this guide we ve used them specifically in the context of security access control For this reason the following glossary of terms defines these terms as used in this guide Access Point A point of entry or exit for an area whose access 1s controlled and monitored by Integra32 E g a door parking gates Antipassback An Access Control feature designed to prevent improper usage APB of a valid card Ethernet A widely used LAN developed by Xerox Digital and Intel Ethernet networks connect up to 1 024 nodes at 10 megabits per second over twisted pair coax and optical fiber Holiday Any days in which the regular weekly Inte
91. n decide to grant access or not Other software functions can also use this feature e g global Antipassback High Security Only cards with High Security privilege will be granted access at access points in High Security mode Facility Code Mode Access points in Facility Code Mode will grant access based upon the card s facility code and not on the card s card number Cards not entered into the system that have the correct facility code will be granted access Report RTE Access granted by a request to exit device will report that event if this feature 1s checked Report Door Not Open The fact that a door was not opened after access was granted at that door can be reported if this feature is checked Report Unknown Format An Unknown Format message indicates that the data received does not correspond to any of the card formats useable by the IRC 2000 URC 2000 This message can be turned off if 1t 1s not required Inhibit ID The cardholder name and card number will be blocked for access granted messages if this feature 1s checked Access granted RTE message will be shown in place of Access granted by card This feature is not applicable for Card PIN schedule Unlock Schedule Select a schedule when unlocking and locking of this access point is required Card PIN Schedule Select a schedule when both Card and PIN are required When this schedule is off only a Card is needed for access to be granted
92. nd their status Live Select Live to display live video from the CCTV camera associated with the selected access point Play Play will bring up a DVR history selection screen so that video connected to an event for the chosen access point can be played back 10 This selection is only available if the optional license for the DVR Software has been purchased and installed This selection is only available if the optional license for the DVR Software has been purchased and installed RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 15 Chapter 3 Monitor Screen O x Date Message Device Card Holder LS 4 19 19 PM Access an Forced entry alarm e itest email Panel 76 1 FIZIOL 4 19 15 PM 4 19 15 PM Access Access point Farced entry alarm Forced entry alarm Reader 1test email Panel 76 1 itest email Panel 76 1 A TR A A Papaes Access ranted Operator Reader test mal Panel761 fe Papon sanare Access ranted Operator Reader test mal Panel761 fe resj2011 367 5364 Access artet Operator reader test mal Panel761 JO e Papaa Access pont Forced entry dam Reader test emal Panel761 id me Papo 383 3864 access raned Operator Reader test mal Panel761 fe ampon 422 296 Access pont Door not pon Reader test mal Panel76t id empon szanom access ranted card Reader test emai Panel761___ rarty Rah Si Integra32 User s Manual RBH Access Technologies Inc Integra3
93. network to the DS7400Xi alarm panel through the option or keypad bus It will emulate a keypad when a link has been provided and report status to the Integra network when included in the list of keypads In order for the alarm panel to poll the emulated keypad the keypad assignment for the alarm panel should be programmed Keypad addresses 1 10 connect to the keypad bus and addresses 11 15 is connected to the option bus The PC100 can monitor all keypads on the bus that are listed under panel properties Keypads A Link to an Event will use an emulated keypad to enter a password followed by a command Ifthe password is not programmed into the alarm panel no operation will take place Whenever a command is executed the green Health LED will turn on The green Health LED will turn off when the alarm panel finishes its poll to the keypad General Panel Properties l x General Keypads PIN Code Links Address Description Je PE OO 32 Panel type PC100 Bozch coo Ao Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 92 Chapter 5 Programming Address The address 32 1s automatically selected at the time of creation and cannot be edited Description To change the default description simply type over it Panel Type The panel type is chosen when the new panel is added and cannot be edited later Enable If the enable check box is not checked then th
94. ns System Options General System options m Number of daps to keep Event History 365 E DWR Message Format old cards after ASC Days so E y DR JIMC LABEL User options oy Keyboard timout min Alarm sounds Print Area Report on Input Alarm on All Printers Activate Card When Visitor Checks in Group Cards Srea status check Interval fen Seconds min recommended El System Options Number of days to keep Event History The System Options window allows the user to customize number of days to keep Event History and Keyboard time out in minutes The default number of days to keep Event History is 365 days Each history file keeps the history information of one calendar day Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 128 Chapter 9 Options If 365 days of history is being kept then only 365 files will be kept When a new history file 1s created the oldest file will be deleted so that only 365 files are maintained Auto void cards after At 1 00 am cards that have not been used within the specified number of days will be automatically deactivated No cards will be deactivated if the number of days is set to Zero DVR Message Format M This option allows sending messages to DVR Servers You can select one of the two options available ASCII or XML For more detailed information see Send Message to DVR on Page74 NOTE Integra32 serve
95. ntegra32 system in the Database Screen Click on the sign to compress it Double clicking the description will either expand or compress the view depending on the sign associated with the text Items that do not have a sign or associated with them will take you to their properties when they are double clicked BR Pntegras2 System Users ce 4 Holidays H Schedules E reas ce Messages se Networks E d Access Levels Right clicking on the different selections will bring up small menus From these menus you can add delete or go to properties for the selected item Right clicking the access point the input or the output will not bring up a menu there are no options to select but will expand the tree view instead Integra32 Database Users The Integra32 system comes with user rbh by default with password password Additional Users Operators can be added and configured the in the Database Screen 2 Delete y 63 rbh Fe Properties mite CF Supervisor Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 30 Chapter 5 Programming General Name user ID and password can be changed or entered in the General tab of the Operator Properties Window Email Address is used by the message server to send the emails for Access point messages configured in Access Point Properties to send the email For more information see page 73 Message server service should be running
96. o be Stand Alone While the host is offline the PC100 continues to monitor activity in the Access Control System allowing interaction between the Access and Alarm Systems General Panel Properties x General Keypads PIN Code Links Inputs Address Description Je Pc OO 32 Panel type PC100 IT 7100 05 Address The address 32 1s automatically selected at the time of creation and cannot be edited Description To change the default description simply type over it Panel Type The panel type is chosen when the new panel is added and cannot be edited later Enable If the enable check box is not checked then the panel will not be shown in the status screen All Access Point Inputs and Outputs under that panel will also be disabled Disabled items are still in the database but are not considered to be part of the system RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 63 Chapter 5 Programming Keypads Panel Properties Address This is the address of the keypad in the DSC system Name Enter here a description or name of the keypad to be shown in the Integra32 system Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 64 Chapter 5 Programming PIN Code Panel Properties Select either 4 Digit Pin Codes Or 6 Digit Pin Codes Pin Codes Enter the four or six digits of each PIN code These
97. ods can be added to the existing schedules Never and Always The system is capable of handling up to forty holidays and one hundred messages RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 9 Chapter 2 Getting to know Integra32 Status Screen This screen gives the operator control of the system through Operator Commands and it provides viewing of the status of the items that have been selected e g 4ccess Points Input Points and Output Points a ae MA E a Access Inputs Outputs Panels reas Visitors a m TR Status Cardholders E P Reader 1 Locked Normal 7 E A Reader 2 Locked Normal ee i Helen a Reader 3 Locked Normal sembpermanent E lA Reader 4 Locked Normal Show Report 3 a E Reader 5 Locked Normal Senn a A Reader 6 Locked Normal ieee Reader Y Locked Normal Reader E Locked Normal Status for items shown is in real time Items are updated as events change keeping the operator up to date Alarm Screen This screen appears in the same pane in place of the Status Screen From here alarms are acknowledged and cleared Date Ss Alarmmessage Operator 3 May 2006 08 38 36 Access point Forced entry alarm Instruction messages can be obtained from the Alarm Details by double clicking or by the right click menu on the alarm messages and actions taken can be noted there as well Integra32 User s Manual RBH Access Techno
98. om being lost It takes about 5 seconds for the PC100 to time out and take over the network When the PC100 has control of the network it will request time and date and keep updating the latest time every 32 polls When the host comes back on lines all log messages are ignored that are time stamped with a date and time earlier than last recorded This prevents old messages from triggering false alarms while allowing the host to update its log file All log messages are passed through the event filter transforming all 128 different log messages into a few events All activity is synchronized to the Summit LSCP bus If the bus is disconnected all activity on the PC100 will halt The PC100 acts like a zone expander to the Summit panel allowing up to 32 zones Each zone is mapped to an element in the IRC network The state of each element in the IRC network will cause a zone to appear open or closed The PC100 acts like an IRC panel at address 32 to the host The host can poll the PC100 to see if it is online request status write to memory and update flash memory General Panel Properties x General Inputs Address Description J2 PE OO 32 Fanel type PC100 Summit canoa Aow Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 96 Chapter 5 Programming Address The address 32 1s automatically selected at the time of creation and cannot be edited Description To change the default
99. ower half of the screen a Check In Click Check In to have the visitor check in to the system a Check Out Click Check Out to have the visitor check out of the system amp Track Click Track to display the access points that the visitor has been granted access to while checked in L Receipt Click Receipt to print a receipt for a visitor s assets E Mail Click on E Mail to send an email to the cardholder being visited For this to work the sender s email information must be configured in VM Configuration under Email Configuration and the being visited cardholder s Profile Tab must have an email address RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 113 Chapter 7 Visitor Manager General E Integras2 AxiomLite Security System isitor 2 E xXx gt A amp 8 93 Add Edit Save Delete Cancel Search Check In Check Out Receipt Track E mail Lastname Firstname Mational ID Card Mumber jo Personal Information Reazon to Visit Address Date of Birth City Phone a E mail Country Employer Fostal Code Time allotted jo Hours Notes Visiting Lastname z Firstname pi Employee Card jo Last Checked In Last Visited Checked In Checked Out Personal Information data is optional and specific to the visitor and not to the card Select who is being visited by clicking on the browse button and sea
100. owledge Unacknowledge Clear Action Messages Activate Card When Visitor Checks In Alarm Details Alarm Screen Alarm sounds Alarms Toolbar Button Antipassback AP Activity Toolbar Button Area and Cardholder Commands Areas Arm Keypad Auto void cards Auto Backup Auto Relock B Backup Badge Options Badge Template Designer C Card PIN Schedule Card Custom Fields Card Format Card Import Utility Cardholders Cards More Fields Tab Options Photo Tab Profile Tab Type Cardholders Toolbar Button Check In Check Out Clear Clear Log Integra32 User s Manual Integra32 3 8 22r4 2 SP15 174 93 80 136 78 73 74 Te 69 71 14 29 27 28 129 27 10 27 129 78 23 36 25 129 142 141 130 147 70 149 46 5 150 96 103 109 104 107 106 104 113 24 113 29 20 Command Bar Command Type Conventions in this guide Copyright D Database Maintenance Database Reports Database Screen Deactivation Date Deduct Usage Disable Forced Entry Disarm Keypad Door Held Open Download DVR Toolbar Button E Elevators eMail Configuration Event Log Screen Exit Extended Unlock Time F F Print Facility Code Mode File Finger Print finger print device Firmware Upgrade First Person Delay Floor Groups Floors Font G Getting to Know Integra32 Global Antipassback Global Links Glossary Group Cards H Handicap Help Help Toolbar Button High Security High Security Privilege
101. r an access point turning Disable Forced Entry on or off and Clear Area After you have selected a command an appropriate device needs to be selected input output or access point Choose the duration of the command 0 127 seconds or 0 126 minutes Not all commands can be timed High Security on and off and Disable Forced Entry on and off cannot be timed A schedule can also be selected for each command the command will only be executed when the schedule is on RBH Access Technologies Inc Chapter 5 Programming Alarms General Details CETW Links Alarms Input Abnormal Alarm schedule Input Normal foo Hever Input Restore Input Trouble P Show Video lf camera assigned on DF tab Show Video on Event e First select an event from the list on the left The alarm will occur when the message appears in the log screen e Then select an Alarm Schedule Causes an alarm when e Then you can select if required an instruction message for the alarm Message creation is described earlier M Show Video If camera assigned on DVR tab Check this box to have the DVR show the camera configured on the DVR tab for this input on configured Alarm M Show Video on Event Check this box to have the DVR show the camera configured on the DVR tab for this input on configured event RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 85 Chapter 5 Programming Ou
102. r know where the visitor is or entering from A site may have more than one entrance that visitors can come in by and the cardholder being visited may need to know where the visitor is M Check the box Send Email as the visitor is checked in to have an email sent automatically to the cardholder being visited by the visitor The being visited cardholder s Profile Tab must have an email address entered for this feature to work This selection is only available if the optional license for the Visitor Management System has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 138 Chapter 9 Options User Fields Visitor Management Configuration be Enter the Description of user fields this description will be then seen on visitor screen Text Field 1 User Tet 000 Number Field 1 User MumberT Text Field 2 UserText2 Number Field 2 User Number Text Field 3 Use Teta Date Field 1 User Date Text Field 4 User Text 4 Text Field 5 Use Tet5 Ok Cancel Define the name of the fields for entering data under the User Fields tabs of Visitor Use this to customize the visitor data saved in your system RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 139 Chapter 10 Links Chapter 10 Links Global Links x Device Select an event Output 1 1 Output On a Qutput d i Is ar Ia a IT coca ho
103. r services need to be restarted whenever switching between the DVR Message Format ASCH and XML DVR The DVR box allows to choose one of the two options available for video display IMC HISTORY or IMC LABEL IMC LABEL displays the camera label on the played back history from the DVR User Options If a user has entered a keyboard time out Integra32 will automatically log out if there is no mouse or keyboard activity for the duration of keyboard time out period Alarm sounds Click in the check box to turn on the alarm sounds which are heard through the computer speaker Click again in the check box to turn it off Print Area Report on Input Alarm on All Printers Click in the check box to turn on the feature click again in the check box to turn it off With this box checked all printers listed on the server will print an area report when the input goes into alarm If the box is not checked the report is printed only on the default printer of the server An input must be selected in the area properties before any report can be printed Activate Card When Visitor Checks In With this box checked a visitor s card will be activated when the visitor is checked in and deactivated when the visitor is checked out Group Cards Global Antipassback by grouping cards function is optional feature This selection tells the system that cards under a single cardholder are to be grouped so that if one of these cards is
104. r the alarm Message creation is described earlier Show Video If camera assigned on DVR tab Check this box to have the DVR show the camera configured on the DVR tab for this access point on the configured Alarm Show Video on Events Check this box to have the DVR show the camera configured on the DVR tab for this access point on the configured message Alarm is not required RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 73 Chapter 5 Programming e Select an operator if need to send an email on the message M Send Email on Alarm Check this box to send the email address configured for the operator selected on Alarm M Send Email on event Check this box to send the email address configured for the operator selected on Event Alarm configuration 1s not required CCTV Main Enterance 151007510 fed This tab 1s available for editing only 1f CCTV license has been installed otherwise we can only send messages to DVR servers 2 This selection is only available if the optional license for the DVR Software has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 74 Chapter 5 Programming x General Modes Time outs Links Alarms CCTV Advanced l Send Messages to DYA Camera Number E OVA IP Address Fort Number fi 25 100 75 140 3300 Lancel The information in this tab is used to inte
105. rch for the appropriate cardholder Department and Employee Card will be filled in by the system Last Check In is also filled in by the system Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 114 Chapter 7 Visitor Management More Fields z Ls E Integras2 AxiomLite Security System isitor E bal A o de a a E ES i Add Edit Save Delete Santel Search Check In Check Ouk Receipt Track E mail Lastname Malik Firstname Salsena Mational ID Card Mumber esse General More Fields Assets Track Photo More Fields License Aer I Humber 58963 User Text 2 User Number 2 User Text 3 User Text 4 User Text 5 User Date 1 visiting zemee Doo O O Bi Firstname PO Department Employee Card fo Last Ghecked In Last Visited cad Checked In pasm 91515 AM Checked Out 4219 2012 9 27 34 AM User Fields are customized fields to hold data pertaining to your visitors The headings for these fields are set in VM Configuration under the User Fields tab RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 115 Chapter 7 Visitor Manager Assets E Integras2 AxiomLite Security System isitor E wx o Mm amp 8 5 Add Edit Save Delete Cancel Search CheckIn Check Out Receipt Track E mail el Lastname Malik Firstname Salsena Mational ID Card Number EE General More Fields Assets
106. re two periods One to go up to 24 00 on the first day and a second to start at 00 00 of the next day H is checked if selected period should be active on Holidays programmed in the system as well After you create a new schedule edit an existing schedule or delete a schedule you will be asked 1f the changes are to be downloaded and the panel initialized now or will it be done later RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 35 Chapter 5 Programming Areas Confirm Change x m Schedule file must be downloaded to all panels and all panels must be initialized Download now Ph WE Add Area Refresh fo e Sales Delete g Warehouse i Wwarehn E Properties Ml Computer Room MM Computer Room boon Main Office al Areas In the Area Properties window the name of the area is entered Access points from which a cardholder can enter or exit the area define the actual area A Clear Area time can also be entered here As well an input and an output both general purpose can be chosen To print out a report of all the cardholders in the area simply put the input into alarm The output will Turn ON automatically when there are no cardholders in the area it must be turned off manually operator command A new Selection Type is added for an optional License is required Antipassback functionality See TB67 Integra32 Area Type GAPB Integra32 User
107. rent functions at each access point In addition every cardholder can perform a unique function at every access point Further links can have several entries allowing execution of multiple commands at each access point when a card is presented This window contains the following fields and options Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 48 Chapter 5 Programming General Reader Options Site codes lame Code Reader Links ID Code Description i 1234 Code Reader Link 1 Reader Side 4 Reader Side E Command Device Duration Schedule ID The number of the code reader link may be system generated by pressing up and down button or user defined A maximum of 16 code reader links can be generated Code Put in the code number These codes can be in the range of 1 32767 Description The user specified description of link Choose one of the two radio buttons Reader side A or B on which code reader link has to be executed Then as with local links you choose which event on what device will cause the link to be executed You can choose up to four things to have happen with one code Dial Out This tab is visible only if the Network to which the panel is connected 1s Modem Network For more information see page 41 URC2000 with ELV The first five tabs General Reader Options Site Codes Alarms amp Code Reader Links are almost the same as
108. rface with a DVR There are two ways that this interface can be accomplished 1 The first is by sending messages to DVR servers Two types of messages can be sent to DVRs ASCII or XML selection of which is made in DVR Message Format as explained under System Options M Send Message to DVR e First select the camera number you want to display from DVR e Then enter the DVR s IP address and Port Number associated with the camera you selected as you could be using more than one DVR For this functionality to work messages need to be configured in system messages menu as explained on page 135 2 This selection is only available if the optional license for the DVR Software has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 82 Chapter 5 Programming e The ASCII XML messages are sent to DVR 5 When lt Event gt is Input then lt Device ID gt Input ID and lt Device Name gt Input name NOTE Integra32 server services need to be restarted whenever switching between the DVR Message Format ASCII and XML in System Options 2 The second way the interface can be used is to associate with a specific DVR DVR are set up in the Database Screen under DVR Ropu a xi aa nee Alarms Send Messages to DWA OWA Name None Camera Information History Information Camera Number B PTZ Camera Fre Event Time Fos
109. rface with a DVR There are two ways that this interface can be accomplished 1 The first is by sending messages to DVR servers Two types of messages can be sent to DVRs ASCII or XML selection of which is made in DVR Message Format as explained under System Options M Send Message to DVR e First select the camera number you want to display from DVR e Then enter the DVR s IP address and Port Number associated with the camera you selected as you could be using more than one DVR For this functionality to work messages need to be configured in system messages tab as explained on page 135 The ASCII messages are sent to DVR in the following format RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 759 Chapter 5 Programming E TCP IP Messages Tester 03 326207 2 15 58 00 Access granted Operator Reader 1 new chip 03 32620172 15 58 05 Access granted Operator Reader new chip 03 3262072 15 58 46 Access denied Invalid card number 551261 Reader 1 new chip Panel 79 2 03 3262017 2 15 58 51 Access denied Invalid card number 551261 Reader 1 new chip Panel 79 2 03 326207 2 15 59 00 Access granted Card gh gj 53070 Reader 1 new chip Panel 79 2 This applications listens on port 3300 And XML messages are sent in the following format TCP IP Messages Tester msg version T gt lt DateTimeUlT Ce 152072 6 55 27 Phi DateTimeUT L gt lt Data gt lt CEameraN umber b lt Camera umber Car
110. rogramming Timed Antipassback Set the amount of time for Timed Antipassback here Timed Antipassback will reset at the end of the programmed time allowing the cardholder to be granted access into an area they are already logged into If a cardholder tries to re enter an area before the timer expires they will cause an antipassback violation Repeat Ignore Time Set the amount of time after a card is read until that card can be use again at that door After the card is read that card will be ignored for the set amount of time Other cards can be used and each will be subject to the ignore time individually Links x a Aa CCTV Advanced Select an event Fareed Eni Command Device Duration Schedule I Output On Output 3 5 Sec o Always 2 Disam Input Y finput O 0 Ses 02 After Hous gt AH MS a g e qj 3 J E Cancel e First select an event The selectable events are Access Granted Access Denied Door Locked Door unlocked Door Held Open Door Not Open Forced Entry Restore High Security On High Security Off 3 Links and 5 Links 3 Links and 5 Links indicate either three or five consecutive Access Granted to execute the link e Then select up to eight commands to be executed with that event The command selection list includes arming or disarming an input turning on or off an output locking or unlocking an access point setting High Security mo
111. rt or Visitors Report Window History Reports Select History Reports from the Reports menu to launch the following window where the user has the option of selecting from many history reports available 5 History Report x File Reports Help E h Reports Preview DVR Date Time Start 1 May 2006 12 00 00 AM End E May 2006 11 59 59 PM Click Preview Print to output a report for all selected events and messages for start to end datetime Integra32 User s Manual Integra32 3 8 22r4 2 SP15 120 RBH Access Technologies Inc File Print Chapter 8 Reports From the file menu the user can Print Select History Path or Exit from the History Report window The Print command will produce a printed report showing the data selected for the chosen report Select History Path Reports Preview If your history files are not being saved to the Integra32 folder then the path to their location will be required The user can select the kind of report they want to preview or print from the Reports menu The options available are Main Cardholders Access Points Inputs Outputs Controllers Alarms Operators and Time amp Attendance The same options are available from the Reports button of the toolbar The user sets the Start Date End Date Start Time and End Time for any report they have selected to preview or print The report will span from the start time of the start date to the end
112. rt to the normal arming schedule Timed Timed commands allow an action to be performed for a specified duration For example turn on an output for five minutes The time can be specified from 1 to 127 seconds or minutes RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 13 Chapter 3 Monitor Screen Access Points Commands Clicking the Reader button on the Command Toolbar depicts the status of Access points on the Device Status Screen N w D El EH Fa H H Reader Inputs Outputs Panels reas Cardholders Feypads Floors Status E Reader 79 2 1 o Locked Normal Reader 79 2 2 Panel fd Panel 79 2 m e Grant access rra O wv Reader 79 3 2 B Lock Door Panel 79 3 E S Reader 79 4 a Unlock Door Panel 79 4 da E Reader 79 4 2 Set Mode High Security E iB Reader 1 Reset Mode Pb APE Enabled E E Reader 2 View Modes Facility Code S Reader 79 1 1 le 5 Reader 2 n Live En Play The following commands for Access points are available by right clicking the selected Access points Commands W Grant Access Unlock the access point for the duration of the access point Unlock Time This command has the same effect on an access point as presenting a valid card Lock Lock an access point or group of access points on a permanent semi permanent or timed basis Unlock Unlock an access point or group of access points on a permanent semi permanen
113. s of information Dealerlnfo can be included rbh ini Notepad loj x File Edit Format Help Dealer Replace RBH Access Technologies Inc with your company name DealerName RBH Access Technologies Inc Diealerintol 905 90 1515 Dealernfoz 2 Automatic Road Suite 108 Dealerlnfos Brampton Ontario Dealernfo4 supportiirbh access com Toolbar Buttons E gt El ok a El a En Log Out Status Alarmas AP Activity Lards Visitors OYA Help RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 7 Chapter 2 Getting to know Integra32 E Log In Es Log Out id Login Logout Press this button to log in or log out of Integra32 system Status System Status Press this button to change the Monitor Screen to display the status of access points inputs outputs and panels ie Aos Al ae Alarms Press this button to change the Status Screen to display alarm messages time and date of alarm and operator ID This change will take place automatically when an Alarm Event occurs AR Activity AP Activity Press this button to toggle on and off the Access Point Activity screen pop up Card BE Cards Press this button to launch Integra32 s cardholder window to program new cards or edit existing cards ia Visitors na Visitors Press this button to launch the Integra32 s visitor window to administer visitors in the system EH DWA DVR Press
114. s rights Before cardholders are entered any additional access levels that are required should be programmed The only default access level 1s Master which always provide access to all doors and all floors General Change the Description of the Access Level in the General tab Access Level Properties Business Hours Access Level RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 93 Chapter 5 Programming Access Level Access Level Properties l General Access Level Elevators Access Level Reader Schedule Reader 1 U2 Mon Fri 30anmn 5 0pm Reader 2 U2 Mon Fri 30arn 5 30 pri Reader 3 U2 Mon Fri 7 30am 5 30pr ai Reader 4 00 Never DT Always Reader 5 02 Mon Fri s0am 5 30pm Sete 03 After Hours cader 04 Mon Fri 8 Obam 5 0 pri Reader 7 04 Mon Fri 8 ODam 5 Ob pr Reader E 04 Mon Fri 8 ODam 5 Ob pr Program the Schedule corresponding to the Reader e g front door amp rear door in Access Level tab Assign one schedule to each access point Use the Never schedule if no access is be allowed at the access point Any access points added after the creation of the Access Level will be given the schedule Never Access levels can easily be edited anytime after they are created if changes are required Elevator readers require a schedule but the actual schedule selected is irrelevant The actual Cardholder s access 1s determined by the
115. shown in the status screen All Access Point Inputs and Outputs under that panel will also be disabled Disabled items are still in the database but are not considered to be part of the system Keypads RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 141 Chapter 10 Links Panel Properties Address This is the address of the keypad in the DSC system Name Enter here a description or name of the keypad to be shown in the Integra32 system PIN Code Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 142 Chapter 9 Links Panel Properties Select either 4 Digit Pin Codes Or 6 Digit Pin Codes Pin Codes Enter the four or six digits of each PIN code These PIN codes must match PIN codes programmed into the DSC system in order for commands from the emulated keypads to affect the DSC system Only eight PIN codes may be entered here Pin Code Name Enter here a description or name for each PIN code Links RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 143 Chapter 10 Links Panel Properties E x General Keypads PIN Code Links Inputs 1 coo Ao Event Select from a pull down list the triggering event Device ID Choose the appropriate device to execute the selected command from a pull down for the selected event Card Enter the card number if applicable that
116. sitor Management System has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 104 Chapter 6 Cardholders Unlock Privilege 2 Cards with this option can unlock or lock access points with a double grant access Two consecutive grant accesses by the same card can toggle the lock unlock mode of an access point High Security Privilege 4 Cards with this option will be granted access on doors in high security mode As well high security mode on a door can be toggled with four consecutive grant accesses Link Execute Privilege 3 5 Cards with this option can execute Global Links with either three or five consecutive grant accesses Three consecutive grant accesses can be programmed with a different link then five consecutive grant accesses Extended Unlock Time Cards with this option will use the Extended Unlock Time instead of the regular Unlock Time Disabled Cards with this option will activate the Handicap Output associated with the access point The Handicap Output follows the activation of the Lock Output by a short delay and 1s used to trigger a door operator to open the door Ignore Auto Void Cards with this option will ignore Auto void if selected any in system settings Cards Up to fifty cards can be added per cardholder New cards can be added for an existing cardholder with the Add button All the cards assigned to a cardholder can be seen on
117. ss Point Activity from the Option menu or click Cancel to cancel your changes Keyboard actions and function keys are denoted by bold typeface For example press F1 to display online help Keyboard control sequences i e using two or more keyboard keys in combination are denoted by keys in bold typeface separated by a plus sign For example press Ctrl Alt Delete to reboot the system Cross references are displayed in blue and will take you to the associated or mentioned part of the manual Click on the cross reference when the curser changes to move to that place in the manual RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 1 Chapter 1 Introducing Integra32 Chapter 1 Introducing Integra32 The Integra32 system integrates Access Control Photo Badging Digital Video Recording and Alarm Monitoring into an elegant building management and security system specifically designed for the smaller application Integra32 s 32 bit software architecture together with Windows2000 WindowsXPTM Windows2003 Windows7 or Windows 2008 operating system ensures that security management needs are met easily and economically with a minimal amount of training The IRC 2000 Intelligent Field Panels utilize flash firmware for easy upgrades This panel uses fully distributed intelligence for off line operations In addition to supporting two card readers each IRC 2000 Intel
118. ss ertedCad Reader 13 Panal Metsa Demsa ___ 25Mar2005 105522 aml Access ganedCad Reader 13 Panal Steve Ta _ 25 Mar 2005105540 aml Access gertedCad Reader 13 Panal Metsa Demas __ 25Mar2005 105554 aml Access ertedCad Reader 13 Panal Chafes Score __ Ma 205 10562 n acces geiedcod Read 1 Pare Meraner Add AE ANALES AND een Mao ed ls lo D de 171 Fi 7 EH Double click the line that has a Camera sign with the event that is to be played back This selection is only available if the optional license for the DVR Software has been purchased and installed Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 124 Chapter 8 Reports Database Reports Select Database Reports from the Reports menu to launch the following window where the user has the option of selecting from many database reports available reate Database Report i xj Select the report from following list Access Levels Report Access Points Report Areas Report Card Holders by Department Cardholder Reader Report Cardholders Report Elevator Elevator Floor Groups Global Links Report Holidays Report Input Points Report Network Controllers Report Operators Report Output Points Report Reader Cardholder Report Time Groups Report Cancel Back Next gt Elnteh The options available for Database Report are Access Levels Report Access Points
119. t or timed basis Set Mode The access point has several operating modes that are normally controlled by the scheduler The operator can override the scheduler and manually control these modes Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 14 Chapter 3 Monitor Screen Reset Mode Reset Mode button is used to turn off the option turned on in Set mode High Security In High Security mode only cards with high security privileges may gain access at this access point APB Enabled Antipassback is an access control feature that prevents cardholders misuse by putting certain restrictions on the use of their cards When the Antipassback feature is enabled cardholders must present their card for entry to and exit from all areas Antipassback prevents a cardholder from using his her card twice at the same access point Facility Code Use this option to turn on off the Facility Code mode when the system checks only the Facility Code portion of the card code All cards with valid Facility Codes will be granted access This feature is typically used when the system is being configured for the first time and the cardholder information is not entered in the database Interlock With this feature enabled a door will not be unlocked if the other door is opened The open door must be closed before the other door will grant access View Mode Select this option to view all the modes available a
120. t Event Time fi Miri e First select a DVR for the pull down list under DVR Name e Next configure the Camera Information Select a camera number indicate whether it s a PTZ camera or not and if it is enter a preset number if applicable e Then set the History Information Set the Pre Event Time and the Post Event Time These times set playback start time how much time before the event time and the playback end time how long to continue the playback after the event time This configuration is used by the History Reports DVR tab to playback video associated with a logged event Links and Alarms tabs are available only for general purpose inputs RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 83 Chapter 5 Programming Links Alarms Select an event Input Alarm bd Command Device Duration Schedule 1 Output On Output 3 0WWsec 7 02 tter Hours y 2 Disable forced entry On Y Reade A 7 f0 amays y Lancel Integra32 User s Manual Integra32 3 8 22r4 2 SP15 84 First select an event Selectable events are Input Abnormal Input alarm Input Normal Input Restore and Input Trouble Then select up to eight commands to be executed with that event The command selection list includes arming or disarming an input turning on or off an output locking or unlocking an access point setting High Security mode on or off fo
121. ted Card Access granted Card Access granted Card Access granted Card Access granted Card Access granted Card Access granted Card Access granted C ard Reader 13 Panel 7 Reader 13 Panel 7 Reader 13 Panel 7 Reader 13 Panel 7 Reader 13 Panel 7 Reader 13 Panel 7 Reader 13 Panel 7 Reader 13 Panel 7 Reader 13 Panel 7 Drrdar 17 rr ld T From this report the user has the option of Printing Exporting the file Refreshing the preview of the report or changing the current view of the report Integra32 User s Manual Integra32 3 8 22r4 2 SP15 123 RBH Access Technologies Inc Chapter 8 Reports DVR Clicking the DVR button from the toolbar of the History Report Cardholders window the user can preview the Send DVR Commands window to select the History Event Command he she wants to send to the DVR Send DYR Commands ol x O x A e play 29 Mar 2005 7 45 00 an A En ZE Mar 2005 1041 44 aml Access ertedCad Reader 13 Panal HaminderKam 25 Mar 2005104325 aml Access ertedCad Feader 13 Panal Meisa Demsa 25 Mar 2005 1047 26 aml Access ertedCard Feader 13 Panal Metsa Demsa ___ 25 Mar 2005104803 aml Access ertedCad Feader 13 Panal Metsa Demsa ___ 25 Mar 2005104858 aml Access ertedCad Feader 13 Panal HarinderKam 25 Mar 2006 104807 aml Access gertedCad Reader 13 Panal Metsa Demara 25Mar2005 105223 aml Access ertedCad Reader 13 Panal Chafes Score 25 Mar 2005 105232 aml Acce
122. tegra32 User s Manual Integra32 3 8 22r4 2 SP15 165 Chapter 12 Program Groups Chapter 12 Program Groups Integra32 Security System Ensure that the Integra32 system is not running before making a selection here in the Program Groups All selections made here will bring up the login window as shown in Chapter 2 on page 4 Accessories E ALE 3 Programs 3 xiomi Security System ES Documents W Integra32 Security System m Integras2 Server Gi Restart ta e Ap Integrase Security System E Settings a 6 Integra32 Add Remove Site E Search Gh Integras2 Data Restore ai Integras Database Maintenance E Help and Support Gb Integra32 Firmware Upgrade She 6 Integra32 Registration E Shut Down Integrazz AxiomLi H Start er 5 11 Windows Expl la Computer Manage MSDE Tool OR Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 166 Chapter 12 Program Groups Je Integra32 Security System qi Integra32 Security System 6 Integra32 Add Remove Site ai Integra32 Data Restore qi Integra32 Database Maintenance ai Integra32 Firmware Upgrade dl Integras2 Registration de Integra32 Server i Restart G Start di stop Je Maintenance de Startup 4 Back E I BS B on Search Programs ana LES Integra32 Security System There are two ways to start the Integra32 system You can either double click the icon that was create
123. ter 4 Alarm Screen The Alarms Screen displays alarm events and pops up automatically when the Alarms option is turned on in the toolbar of the main screen Date jAlammessage 2 Operator 60722011 16 22 31 Access granted Card Reader Itest email Kanty Riarh 454349 Fo Unacknowledge 2 Clear Clear all Details 7 21 2011 16 19 21 Access point Forced entry alarm Ri Live En Play Acknowledge Unacknowledge Clear Right clicking the alarm event on the Alarm Screen gives the option to acknowledge the Alarm Right clicking on an Acknowledged Alarm gives the options to either clear or unacknowledge the alarm Once an alarm is acknowledged only the operator that acknowledged that alarm can clear it A maximum of one hundred and fifty alarms can be held in the alarm buffer Any alarms received when the buffer is full are logged to history but do not get sent to the Alarm Screen Alarm Details The user can see the details of an alarm event in Alarm Details Window by double clicking the alarm event in the Alarm Screen Date This box shows the date and time that the alarm occurred RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 217 Chapter 4 Alarm Screen Age The age of an alarm is the number of seconds since the alarm happened Status Status shows whether the alarm has been acknowledged Alarm Alarm provides a description of the alarm Instructions This box will display instr
124. that is stored in the database or acquire the picture of the cardholder if a camera is installed on your computer Fingerprint fields can be added to the badge Signature fields can be added to the badge Barcode fields can be added to the badge A shape field can also be added to enhance your badge In the properties of the badge you can set the background colour of the badge you can also add a background picture e You can right click on a field to modify its properties or to delete it 37 To use these options you may need optional hardware devices 38 To use these options you may need optional hardware devices 2 To use the Barcode field you need to install barcode fonts in your control panel which are available in the fonts Resources folder of your Integra CD Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 154 Chapter 11 Tools Card Custom Fields Integra32 AxiomLite Cardholders i x yy Wd e Edit Save Cancel Last name First name Initials Lardnumber A ee eee More Fields User Number User Numbers User Text 1 User Text 2 AA User Text 3 User Datel User Text 4 K User Text 5 E User Textb E Double click on a header while in the Edit Mode to change the name of the user field This change will be shown in the More Fields tab of every cardholder Rename Control i x Enter New Name Cancel
125. the manufacturer selected in Badge tab of system options Last Name Enter the cardholder s surname First Name Enter the cardholder s given name Initials Up to six characters can be entered 2 This selection is only available if the optional license for the Finger Print Reader has been purchased and installed RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 97 Chapter 6 Cardholders Cardnumber Enter a number here to be used as a search parameter Multi Cards Multi Cards l x Start Cardnumber Activation Date 4 Map 2006 End Cardnumber Expiry Date 1 Jan 2036 Access Level No ACCESS Multi Cards utility can add multiple cards in a sequence in the cardholder window e Putin the Start and End card number e Assign the Expiry date if any e Assign the Access Level from the drop down menu of the Access Levels configured in your system Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 98 Chapter 6 Cardholders Multi Cards x Start Cardnumber Actyation Date 29095 29 Mar 2005 E End Cardnumber Expiry Date 29500 1 Jan 2038 Access Level No Access 01 Master U2 Accounting 03 Sales O4 Warehouse 05 Shipping O6 Manager e Click on Start button to add the cards Multi Cards x Start Cardnumber Actyation Date 23095 29 Mar 2005 z End Cardnumber Expiry Date 2
126. time of the end date unless the daily report box is checked If the daily report box is checked then the report will still span from the start date to the end date but only include the times between the start time and end time of each day Clicking the Preview button of the toolbar the user can preview or print any of the selected reports for selected time period To understand the History Reports Window in detail let s take the example of one of the selected options Cardholders From Reports menu or Reports button select Cardholders to show the following screen RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 121 Chapter 8 Reports e History Report Card Holder x File Reports Help Le Preview E Reports Date Time fizo ee ee Start 24 Apr 2006 12 00 00 M T izi Bepon End 24 Apr 2006 11 59 59 PM Select readers default All ll Readers Cardholders ei Access Denied Department 4 Access Granted fal e E E i Cardholder Action Entry reader Exit reader IY Access Requested Select the Start and End Date and Time for the time period you want to preview the report for Ifthe report is to cover only specific hours each day then check Daily Report so that the Start and End Time will be applied each day Click the Select Readers button to select the readers you want on this report to preview or print All readers wil
127. tion clears the event log of selected controller s The database portion of memory is untouched The results will be displayed on the Log Screen Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 20 Chapter 3 Monitor Screen Schedule Inquiry This query 1s used to find out the current state of the time schedules It will list on the Log Screen which schedules are on and which is off Commands PC100 Summit The following commands for panels are available by right clicking the selected PC100 Summit panel Version The Version queries the selected PC100 for the firmware version it is running The version number will be displayed on the Log Screen Set Date Time Click on the Set Date Time to launch the Set Panel Date Time Screen e The Get Local button is used to retrieve the current date and time settings from the PC s internal clock e The Set button is used to upload the selected Date Time settings to the selected PC 100 e The Close button is used to close the Set Panel Date Time Window Get Date Time This command queries the PC100 for its current date and time and displays it on the Log Screen Download The Download function allows the operator to manually repopulate the PC100 memory from the database on the server Click on nputs to download the data Download messages are posted to the log as files are sent verifying the number of records sent for the fi
128. tputs a Outputs General The Description and Type of the output can be changed programmed in the General tab e The output type can be General Purpose Lock for Reader A Lock for Reader B Handicap for Reader A Handicap for Reader B Alarm Shunt A Alarm Shunt B Modem Power Details utp t On State Energized bl Output State On during time group 02 After Hours M Report to PC Choose Energized De energized On State and select a schedule for Output State On During Time Group from the Details tab Also select the option of Report to PC if it is needed Output State On During Time Group and Report to PC are programmable for general purpose outputs only Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 86 Chapter 5 Programming CCTV General Details LLTW Links Camera Mumber oo OVA IP Address Port Number ee This tab is available for editing only if CCTV license has been installed otherwise we can only send messages to DVR servers The information in this tab is used to interface with a DVR There are two ways that this interface can be accomplished 1 The first is by sending messages to DVR servers Two types of messages can be sent to DVRs ASCII or XML selection of which is made in DVR Message Format as explained under System Options M Send Message to DVR e First select the camera number you
129. uction messages assigned to the alarm Action Messages The operators can enter their own message into this box indicating what action was taken because of this alarm Alarm Details xX Wor e Date Age Status Alarm Instructions T 4 Acton Messages Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 28 Chapter 4 Alarm Screen Acknowledge Acknowledge the highlighted alarm with this selection Y Acknowledge All Acknowledge all of the alarms in the Alarm Window with this selection Unacknowledge Unacknowledge the highlighted alarm with this selection Clear Clear the highlighted acknowledged alarm with this selection Clear All Clear all of the acknowledged alarms in the Alarm Window with this selection Live Select Live to display live video from the CCTV camera associated with the selected alarm event Play Play will play back the video connected to the selected alarm event for the chosen time period configured in CCTV tab This selection is only available if the optional license for the DVR Software has been purchased and installed S This selection is only available if the optional license for the DVR Software has been purchased and installed RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 29 Chapter 5 Programming Chapter 5 Programming Click on the sign to expand the tree view of your I
130. uire their respective integration software to be installed for proper operation Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 130 Chapter 9 Options Designate as well the format to save the image as and what printer to use for printing badges M Also click in the check box for double sided printing of badges M Check Use Dazzle 90 if you are using a Dazzle 90 for photo capture M If you are connecting Biometric Readers to your COM port check the box RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 131 Chapter 9 Options Magnetic Encoder Setup Clicking in the Magnetic Encoder Setup button under the Badge tab of System Options window will launch the following window to setup properties for magnetic encoding Magnetic Encoding Setup x Printer Model None Track 1 Track 2 Track 3 Field Name None Field Length ee Cancel Select the printer model in this window The fields to encode can be selected for each track once the printer model is selected Note gt The field length is fixed and cannot be changed gt If None is selected for the printer model the track fields for encoding will not be available gt The printer properties for encoding should be setup for the printer from the control panel Font You can change the default font for the main client screen by browsing the font list select a font
131. ur eight output relay boards may be used with each URC2000 Elevator Control These outputs may be split between the two readers of the panel or all outputs may be used with just one reader Use the scroll buttons to select the number of relay boards that are connected Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 90 Chapter 5 Programming Pam AAA Number of ELC boards Wm Floor description o OA Output 24 Output 25 Output 26 Output 27 Output 8 Output 3 Output 30 Output 31 Output 32 Rename the outputs for your convenience Panels AAA General Reader Options Site codes Alarms Code Reader Links Outputs Number of ELC boards a Floor description 2 Cab A 12th Floor Cab A 13th Floor Cab A 14th Floor j Cab A 15th Floor Cab A 16th Floor Cab A 17th Floor Cab B 2nd Floor Cab B 3rd Floor Cab B 4th Floor 20 Cab B 5th Floor hd Cancel RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 91 Chapter 5 Programming PC100 IRC2000 panels connected along with the PC100 must be running firmware version 76 or higher for the PC100 and the IRC2000 panels to function together correctly Bosch It is recommended that the user be familiar with the DS7400X1 panel and has the ability to program PIN codes and parameters into the panel The PC100 interface has been designed to connect the Integra32
132. used to enter an area all of the cards in the group will not be RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 129 Chapter 9 Options allowed to be used to go into the same area Any one of the cards may be used to go into another area For this feature to work PC Decision Required and Hard Antipassback Page 78 must be ON For more detailed information refer to TB71 Integra32 Group Cards GAPB Area Status Check Interval 60 Seconds is the default time for Area checking intervals to check if any of the Area which has an output configured is empty so that the specified output is turned on The users are given the option to change this timing 1f required Badge xl Picture device type i General e Picture device Camera 1 Signature device Device 1 Fingerprint device BFF Sereg Save File As JPG Printer Mame Microsoft APS Document Writer Duplex Badge Printing Use Dazzle30 settings for photo capture Biometric reader connected to local comport Magnetic Encoder Setup Use this tab to define properties of the Badging utilities Designate where the cardholder s image signature and fingerprint will be acquired For devices to be listed here they must first be installed in the operating system according to the requirements of Badges They must also be Twain devices IP cameras can be selected as well A couple finger print devices are supported They req
133. will trigger the selected command when it is associated with the chosen device and selected event e g execute the command when card 1234 is granted access at reader 1 Command Select the command to be executed on the chosen keypad from a pull down list Arm Keypad Disarm Keypad or Arm Perimeter Keypad Choose which keypad the command 1s to be executed on Pin Code Select a valid PIN code The command will be executed as though this PIN code had been entered Inputs Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 144 Chapter 9 Links Panel Properties Input E Input E Input 7 Zone There are 256 zones Description The zone name or description can be edited here Keypad Select the Keypad assigned to various zones from the drop down menu RBH Access Technologies Inc Integra32 User s Manual Integra32 3 8 22r4 2 SP15 145 Chapter 10 Links Access Points Inputs and Outputs Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 146 Chapter 11 Tools Chapter 11 Tools Backup The Integra32 Backup Configuration Wizard is used to backup your data files You can run the Backup immediately or configure the auto backup to run at a later time Your Operating System most likely will also have its own backup utility It doesn t matter what method you use as long as you backup your files regularly
134. y window will show all access granted and or access denied events that occur at selected access points J Grant Access Grant access will grant access at the reader currently shown in the Reader box of the AP Activity window More Less The More button will add a section to the bottom of the window that will display the contents of the cardholder s notes tab Information about the cardholder that needs to be readily available can be display this way The Less button will remove this extension Integra32 User s Manual RBH Access Technologies Inc Integra32 3 8 22r4 2 SP15 136 Chapter 9 Options Hide The Hide button will remove the AP Activity window from view without turning it off You can also minimize this window The difference between hiding and minimizing 1s that a hidden window won t show up on the task bar RBH Access Technologies Inc Integra32 _ User s Manual Integra32 3 8 22r4 2 SP15 137 Chapter 9 Options Visitor Management Configuration33 Email Configuration To send emails to cardholders announcing their visitors you need to configure the sender s email information on the screen depicted below w Visitors Management Configration xX Enter the Email Configuration This settings will be used to send email to person being visited Sender Name Senders Email address SMTP Server Send Email as the visitor ig checked in The Sender Name is used to let the cardholde

Integra32 User Manual - Sharp`s Lock & Alarm

Contents

Download Pdf Manuals

Related Search

Related Contents

Integra32 User Manual - Sharp`s Lock &amp; Alarm

Contents

Download Pdf Manuals

Related Search

Related Contents

Integra32 User Manual - Sharp`s Lock & Alarm