Home

gtgps user manual

1. see 20 17 3 Configuration of the module via PC ssseesesssssssesseeeeeee eene en eene enne tnne tene tren trennen nennen net 17 4 Installation of the product and connection diagram 17 5 Installation instruction and connection diagram of security system for house mini mobile cottages boats 26 17 6 Vehicle s GSM GPS messages system Installation manual and connection diagram 27 17 7 Testing and diagnostics een le peret ebee oceano gae EET ipu spe ESEESE e Dae yug du ean sieeve 30 I8 Software updating ee ete teen erbe tite DE Dart ee bin eb E PUR cun gus ge Te pudet eu uuo E A N Sega bubus 30 huoc CC 31 EN Good I 31 2e ADER cu LEE 32 Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 3 1 Safety requirements Before applying the module in operation please read this user s guide Any operations related with mounting of the module and connecting of peripheral devices should be performed only after unplugging the module from the mains 2 Application of the device GSM GPS Automatic Vehicle Location and Tracking module GTGPS hereinafter the Module is designed for sending of GSM SMS messages and GPS location to the mobile phone of a user GTGPS module may be used
2. o CTRL SMS DIAL output used for remote control via short call or SMS E g for ignition blocking for gate control or for remote vehicle starting etc o SIREN output used for connection of siren Siren time can be changed o BUZER sound signalling device In the event of zone alarm beeps continuously When security system starts calculating exit delay the user is able to hear short repetitive sound signals When 10 seconds are left till the begging of activation signals are being repeated each 0 5 seconds If after expiry of the delay time all zones remain unalarmed the system turns into ARM state along with beep sound to confirm the action o ARM state state of alarm system ARM DISARM May be used for light indication When the output is set to operate in pulse mode this feature may be used to close car windows or sunroof on arming Impulse time should be set 20 30 seconds On arming the output will generate signal to close windows o Inputs OK if any of zones is disturbed the output will be alarmed This feature is usually used for indication whether all zones are in order o Light Flash used for connection of light signal Upon alarm of the security system the light starts blinking Lights will also blink when arming disarming the security system This feature may be applied to connect vehicle direction signals e Output inversion e Output type level or impulse e Output impulse duration 1 65535 seconds 12
3. capote shock fuel tank etc SMS message is being sent to a user in line with a short call This is to reduce the probability that a user will not observe SMS message It is possible to send SMS and to call to 16 users The algorithm of message sending is SMS1 SMS2 SMSn till all SMS messages will be send After DIALI DIAL2 DIALn All messages are being sent until all users will be notified about the event Preferred messages and texts of these messages should be defined when programming the module The module understands when the call is rejected and will not repeat calling When the module is calling to the user s phone the user can not reject the call at least 15 seconds Otherwise the module will understand that the user s number is busy and will try to repeat the call again In a case the user s number is busy in fact the module will make repetitive calls following the programmed number of calls Efficiency of this function depends on interpretation of call control by the operator in some cases the operator may wrongly interpret the call and thus the module will make repetitive calls each 60 seconds following the programmed number of repetitions by default 3 repetitions In such case GSM operator may be changed or simply the amount of DIAL repetitions reduced Parameters of the module are set by sending SMS or via PC by using standard miniUSB cable and configuration software SERA which is available to download at www topkodas lt In order
4. e e To open http maps google com website e To open SMS message in a phone and to type geographical coordinates in Google Maps search field longitude and latitude as shown in the picture aioi Eile Edit View History Bookmarks Tools Help ik G e x A S nedimaps aoogle com LW e iki 54 898657 23 902895 GoogleMaps New Help Sign in Web Images Videos Maps News Shopping Gmail more v Google maps 54 898657 23 902895 x Search Maps Show search options gt Print Send es Link e mr yee ES we Map Satellite Earth X S 8 2 Kauno meno so Meli Kauno E mokykla oe muziejus Meninink amp w namai amp sak 2 E S w Y oe 2 gene a e 2 O E PA v o 2 ue e Sk or s Vytauto Did io tiniu g ro gatv E262 a karo muziejus iaus ga K Don p de jas gi K Donelai io gatve wa pies 2 K Donelai A g 8 1 dj Kauno 2 Kat Q filharmonija S techno o univer AS 2 E amp 2 2 Lai Kauno Tado E 2 Sv s al ja Ivanausko z Kauno Sv zoologijos muziejus Laisves alja A Gertr dos ja zd z ba ny ia km 2010 Google Map data EB Tele Atlas Terms of Use inp 380 thio Lietjivos istorin z zident ra Sto TT How to use Google Earth map Download Google Earth program from the internet http earth google com e Install the application e Launch GoogleEarth and ente
5. the module to PC via programming cable Full change of parameters is possible only via PC by connecting programming cable If possible we recommend to configure the module via PC 17 1 SIM card GTGPS module is not locked with a particular GSM network This means that a user may use SIM card of any GSM service provider with a possibility to send SMS and to call In order to control the module via a short call SIM card should be have Caller ID option Usually SIM cards have such option If your card can not identify a caller please contact GSM service provide or use another SIM card Locate SIM card into a holder Card s circuitry should look downward and card s key cut angle should look upwards The card holder is of Push Push type This means that after pushing the card once it is fixed and after pushing it again it is released Locate SIM card into a holder Gently push it Fix SIM card Note do not locate SIM card with force because you may damage SIM card holder 17 2 Configuration and control of GSM communication module via SMS messages Only basic parameters of the module shown in the table 171 may be configured via SMS messages All parameters of the module may be changed via USB by using configuration software SERA Configuration of the module via SMS messages may be performed only with installer s password 171 Command structure e Verifier INST Install This verifier is used for configuration of parameters of
6. IMEI 356895030001799 Inputs ns M ow2 Out2 On Off SMcard READY i INA Service SMS Text Signal level B II Custom SMS Text Ns outs Out3 On Off Testing and Diagnostic M IN6 Registration JRegistered home network I outa Out4 On Off SMS Service Centre Address I W 575 Batt ery 437069899992 14 8 jga7 Temperature 0 ps UM GPS info GTGPS Latitude 5 833855 Fix Quality Fixed P 23 9041 72 system state INN Longtusel GPS Mode po i m System voltage 1316 y 7522 ape Altitude Saused 93 ag rss Time urc 09 19 2010 14 21 54 satin view 12 Temperature E ADC Speed 2 0mm Geofence pist 2498km Switch on testing mode Switch off testing mode PDOP VDOP HDOP 2307 507 50 cows Connected 18 Software updating Updating of firmware version should be performed via PC The following is necessary e mini USB configuration cable e configuration software SERA e the new software version which may downloaded at www topkodas lt More about software updating process see user manual of the software SERA Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 30 ATEM Annexes 1 Annex Central alarm system o vacuum central lock Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas It 31 Annex 2 IIS WHY Ae N 3S WYVSIC HES WHY SWOOL lt Cera nen TUE Te OTE PTO DTU OR
7. Timers of the security system Entry Delay time period during which the user after passing Delay zone should manage to disarm the security system Exit Delay time period during which the user should manage to leave the object and pass Delay zone Siren time Siren switch on time in the event of alarm Test time time of automatic periodical test 13 Automatic periodical test sending Periodical test may be used for communication control of the module Test sending time is programmable Test Time Asynchronous periodical test may be programmed This means that after each activation of the system test time is being calculated from the beginning Reset test counter ARMing Test sending may be disabled by setting time 00 Periodical test may be used for SIM card s account control The following parameters of the module are available in a test message GSM communication strength power supply voltage temperature IMEI number of the module software version 14 GPS User s guide Having installed GTGPS module you will be able to determine the geographic location of your vehicle The module will send you SMS message including GPS location e Ifan authorized user makes a call to the module and the right to request GPS geographic location is granted to the said user More info see in Users e Against SMS with request More info see in the chapters 7 2 and 14 1 e If Geofence alarm is triggered This function is to inform a user
8. convenient for him 58 command changes the state of selected output for set time limit If you wish to change invert OUT1 OUT4 states and to receive information about output states the following message should be sent USER123456 50 1 503 e 123456 user code e 50 to change state of selected output Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 23 e 1 to change state of first output OUTI e 50 to change state of selected output e 3 tochange state of third output OUT3 If you wish to activate OUT1 and to deactivate OUT2 USER123456 511520 e 123456 user code 51 set OUTI state deactivated output 52 set OUT2 state 0 deactivated output Output control by selecting trigerring time interval USER123456 58 1 48 enable OUTI for 48 seconds USER123456 58 2 5 enable OUT2 for 5 seconds e 123456 user code e 58 command see table e enable OUTI output 1 OUTI 2 OUT2 3 OUT3 4 OUT4 e d e 48 Output triggering time limit set for 48 seconds After time limit of 48 seconds OUT1 will be disabled automatically e d ARM DISARM of the security system via SMS message To DISARM the security system USER123456 59 0 or to ARM the security system USER123456 59 1 It is possible to receive test of the module on the basis if request command USER123456 80 6 e 123456 user code e 80 information request command see table No 3 e 6 command test reque
9. coordinates and automatically activate Geofence security 14 6 GPS receiver testing and preparation to operate When installing the module GPS antenna can not be covered by metal construction For normal operation of the module sufficient communication quality is necessary which is characterized by PDOP Position dilution of precision a definition which describes satellites layout and precision in real time This is a coefficient which is visible in SERA diagnostics window or in GPS report SMS messages thus by providing information on precision of works being carried out If the coefficient is low work conditions are perfect and measurement bias is minimal if the coefficient is high it is recommenced to relocate the antenna If SERA diagnostics window will register PDOP HDOP VDOP too high the module will simply not to allow to carry out an appropriate works When measuring under PDOP HDPO VDOP values 1 3 measuring bias will be minimal For normal operation of the module PDOP HDPO VDOP values should not exceed 7 10 15 Messages sending Messages are being sent in the event of alarm after ARM DISARM of the security system if specified in the configuration upon test sending time if specified in the configuration after changing the module configuration if specified in the configuration upon sending request about parameters command code 80 SMS about alarm of the security system is doubled with a short telephone call if specifie
10. electromagnetic lock via free short call ARM DISARM of the system via free short call ARM DISARM of the system with the factory remote control central lock Temperature measurement For temperature control tracking alarm and control Voltage measurement Voltage monitoring and alarm External microphone Remote voice listening option via external microphone Option to connect BELL for alarm indication System state BUZZER Optional output type FLASH feature may be used for direction indicators on arming or disarming or in the event of alarm Optional output type Sending of periodical test including system parameters SMS about state of each sensor alarms power supply voltage and GSM communication level Built in GSM module Testing and diagnostic of the module via USB by using program SERA Remote set up via SMS messages Configuration of the module via USB Free configuration program SERA Very compact Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 2 Content l Safetyrequiremenhts oO Ashes Hea SS ee SS ee aed gee OO Gs DIU 4 2 Applicationof the device ie che ee eetreeie reine Pe cs cack Prnt debe praece Pep eee pe EE EE o EEE TET 4 3 JUsed definitions and terms uester nre ERES REG ECRIRE E Pc MEE Er PRI beri tr eie eG 4 4 Short description of the operation principle sees nennen nene rennen eene trne tenete 5 MEN cori E 5 OE sui
11. for protection of all types of vehicles for determining geographic location of a vehicle and for remote tracking via GMS network The module may be used for protection of a vehicle or in combination with the vehicle s security system which has control lock control In the event of burglary the device depending on programmed operation algorithm is able to call or to send SMS to up to 16 users A user is able to hear what is going on in his vehicle after answering a call or he may make a call by himself A user is able to receive an SMS with detailed information about status of each protected zone and number of alarm events The user is able to control the device via SMS messages only if he knows user s password If a call is being performed from the telephone number not included in the system s data base the call is rejected immediately The module has system voltage control If power supply voltage drops below the defined value a user automatically will be notified via SMS The SMS message includes voltage of backup battery The module has external temperature sensor A user receives information about temperature alarms and restores via SMS messages The SMS on voltage of the module and ambient temperature is also available Temperature may be measured in Celsius and Fahrenheit SMS periodical test ensures constant control of the module The module is able to send periodical test Test time is programmable The test will include all essential infor
12. of the security system Auto rearm If the function Auto reARM is on the module will automatically return to ARM state if during Entry Delay none of zones was alarmed This feature is active only if the module was deactivated via telephone DIAL or SMS This protects from random disabling of the system via telephone 9 6 Enabling of the security system via IN6 input Force ARMing function This feature is comfortable to use when the module operates in parallel with other security system For example if default security system is used in a vehicle thus bell signal may be used for IN6 If default security system will be alarmed for appropriate reasons and will activate the bell thus GTGPS module will automatically turn into ARM state And will send all information in relation to alarmed sensors Thus the user gains additional protection from undesirable deactivation of GTGPS module This IN6 feature may be disabled 9 7 Blocking ARM INS additional feature This is additional feature IN5 which enables to block activation of ARM State This feature may be applied in vehicles by connecting IN5 input to ignition If GTGPS module was disabled and afterwards ignition was turned on thus while the ignition will remain on the module would not be able to enter into ARM state This feature may be disabled Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 11 9 8 Bell confirmation signal by armi
13. off Out output deactivation text changing up to 16 symbols the end symbol 45 Out2 OFF Locking off Out2 output deactivation text changing up to 16 symbols the end symbol 46 Out3 OFF 4 Kondic off Out3 output deactivation text changing up to 16 symbols the end symbol 47 Out4 OFF IMMO offit Out4 output deactivation text changing up to 16 symbols the end symbol OUTI OUT2 OUT3 OUTA output states 1 Inverted 0 Normal 48 0000 1111 Example outputs OUTI OUT2 OUT3 OUTA are inverted Description of output Out1 Out2 Out3 Out4 operation algorithm 49 0000 1024 0 CTRL 1 SIREN 2 BUZZER 3 ARM state 4 Zones OK 5 Flash In the above example OUTI will operate in siren mode OUT2 for remote control OUT3 to connect buzzer BUZZER OUT4 Zones OK 1 OUT1 2 OUT2 3 OUT3 4 OUT4 Change state of selected OUT output Output 50 none 1 state changes every time after sending command code Explanation see below the table 51 none Oorl Activates or deactivates OUTI output 0 deactivates 1 activates 52 none Oorl Activates or deactivates OUT2 output 0 deactivates 1 activates 53 none Oorl Activates or deactivates OUT3 output 0 deactivates activates 54 none Oorl Activates or deactivates OUT4 output 0 deactivates activates ARM DISARM command 0 DISARM the security system 1 ARM the security 59 none Oorl system Command to enter new user for remote control via short call Command par
14. possible from heating elements of Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 29 passengers saloon and sources of electromagnetic disturbances auto computer air conditioning system relay units Do not mount the unit directly to metal parts of the vehicle in order to avoid accumulation of condensate within system block The module should be mounted thus connectors of wires to be at the bottom side Wires of the security system can not be laid near moving or hot parts of a vehicle For fastening use screws or plastic fastening straps The battery should be installed in a place protected from impact of humidity or other materials causing corrosion as far as possible from heating elements of passengers saloon It is necessary to install fuses mentioned in the diagram Fuse seat should be installed as near as possible to the car battery 17 7 Testing and diagnostics Diagnostics and testing of the module may be performed via USB port with software SERA The software will show system input output GPS GSM states in real time Thus it would be easier to evaluate whether the module operates as appropriate SERA GTGPS configuration j nix File Setup Devices Update Help lal sls alal GTGPS Configuration System Options Testing window GSM Communications Cnputs ADC values Outputs states GSM info IN1 se ee Control n out Out On Off
15. to activate voice listening it is necessary to call from a user s telephone number When calling the module will immediately activate voice listening which will last as long as the user will reject the call or when the module will start performing other commands Calls from other telephone numbers of non authorized users are ignored 5 Package content GT GPS module 1 pcs System cable 1pcs GSM antenna 1 pcs 9 s A pute E if 2 4 GPS active antenna 1 pcs 2 2 kOhm resistors 4 pcs 1 kOhm resistors 6 pcs J unm System state indicator y External temperature sensor attached External microphone attached on the LED attached on the on the system cable 1 pcs system cable 1 pcs system cable 1 pcs Mini CD 1 pcs e User s guide in PDF e Program SERA e USB drivers Mini USB cable Shipping Package Note Some package content may be optional Please ask seller for more information Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 5 6 Specifications Parameters of built in GSM module Quad band 850 900 1800 1900 MHz Sending of SMS messages Receiving of calls and dialling Microphone PGS parameters Chipset n RU RIBERRU IIBER REREERO IURI AR RET AR1511 Atheros GPS chip 20 channel SUPPI S EE AGPS WAAS EGNOS and MSAS General Frequency renee RO E DRE E SERE L1 1575 42MHz Accuracy Position 2 uH
16. type Normal Open this means that the alarm will be send when the input will be connected with ground V e NC input type Normal Close this means that the alarm will be send when the circuit between input and ground V will be broken e EOL end of line resistor input type with resistor e Service messages ARM DISARM test resetting of the system e DIAL the system makes a call to the number specified e Pull up resistor the pull up resistor is that it weakly pulls the voltage of the wire it s connected to towards V or whatever voltage represents a logic high e MIC microphone e COM negative power supply terminal e V positive power supply terminal e SSR Solid State Relay e Caller ID Caller s identification e AVL Automatic Vehicle Location e Geofence the territory in a selected radius around the set point This function is to inform a user that the object crossed the defined zone Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 4 4 Short description of the operation principle The module has built in GPS system to define a geographic location of the object and to transfer the said information to a user s mobile phone The module transfers messages about event of the security system to the mobile phone of a user via GSM communication channel Upon alarm response of the security system the module will generate SMS message about alarmed sensors door
17. 0s s Zone Action isse v The following parameters may be set for all inputs Text of SMS messages for alarms and restores This text will be included when sending SMS message to a user about alarms and restores of zones Input types NC NO EOL These parameters should be set depending on type of zone connection Definitions of input application o Delay Entry Exit zone Set Entry delay and Exit Delay are applied for this zone Such type zones are used for connection of door sensor o Interior disturbance of this type of the zone will not be responded if alarm of Delay type zone occurred and Entry Dlay or Exit Delay time still have not run out Such type zones may be used for connection of motion sensor in front of the door The input will be activated immediately if the door has not been opened before o Instant Instant zone Upon disturbance of this zone the system will immediately activate burglary alarm o 24 hours Upon disturbance of this zone the system will activate burglary alarm not depending whether the security system is in ARM or in DISARM modes The applications of this type zones are safes storehouses tampers of the sensors o Silent silent zone is always active not depending on whether the security system is ARM or DISARM Upon disturbance of this zone SMS messages are being generated but the siren will not be activated These zones may be applied for voltage temperature c
18. 16 symbols the end symbol 27 Low Battery Battery IN7 input name changing up to 16 symbols the end symbol 28 Low Temperature Low Temp IN8 temperature alarm name changing up to 16 symbols the end symbol 7 31 Rest Luggage Closed Luggage INI input restore name changing up to 16 symbols the end symbol 32 Rest Bonnet Closed Bonnet IN2 input restore name changing up to 16 symbols the end symbol 33 Rest Door Closed Bonnet IN3 input restore name changing up to 16 symbols the end symbol 34 Rest Microwave Rest micr INA input restore name changing up to 16 symbols the end symbol 35 Ignition Off Ignition INS input restore name changing up to 16 symbols the end symbol 36 Siren Off Siren off IN6 input restore name changing up to 16 symbols the end symbol 37 Battery Restore Battery Restore IN7 input restore name changing up to 16 symbols the end symbol 38 Temp Restore Temperature Res IN8 temperature restore name changing up to 16 symbols the end symbol 40 Outl ON Ignition on Out output activation text changing up to 16 symbols the end symbol 7 41 Out2 ON Locking on Out2 output activation text changing up to 16 symbols the end symbol 42 Out3 ON Kondic on Out3 output activation text changing up to 16 symbols the end symbol 43 Out4 ON IMMO Out4 output activation text changing up to 16 symbols the end symbol 7 Ou 44 Outl OFF Ignition
19. G ETON TNR UTNRETAUTAR TNR UTA PER PTN B FTT ETE PTS PT Ry 4 PUTA TG R TN RT TR PTS ROTOR OTS TOR TNR DTS ETON PTO FTN ETE PT OR PUES Su100L pA SD cees seks es ceases be kbees Cees ceases sees seen eee Saar seen bee bee Sees tees cee eee eee eee eee sees sees eee TuPTARPTUETTUPT SWOOL lt SWOOL lt BA4HBRA4dHASZHRALAHA N 407 sonsnonenensonan AF T ubpTUVEPTEPTUEP N xooqun NR ee ee et N 901 arcane sssaaa A 9 npo N jo B e1S 32 www topkodas lt Automatic Vehicle Location AVL and Tracking system using GPS GSM
20. N S ss 12V E UE 5b 50 Signal to auto close y z g 5 Windows Sunroof and Side E vY OND GND 12V P Turn Lamps Mirrors upon locking N To CAR central Loc Siren and Unlock signals GND GND GND The module configuration blank sample for this diagram you will find after installing configuration program SERA located in the directory ConfigTemplates File name GTGPS_v1_VehicleAlarm tcfg The connection diagram of the module is in parallel with already available security system Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 28 AcI punoip cmo 1osusg ino 10suog Teusisg xo qun enue eUsIS x20 enUED Siren O o Mil yams jueurreduioo ogv3sn T O Heh yams jouuoq ouIsUq O jnujs 100P IAP ur YNMS GND GND GND E S 5i Lugage Sensor Signal Siren Si Vs HS a T xu LLL ET 2 pow p T e E MOJ 94 U2910 Cc AYALLVA AVO Wooly a AOT X a e d UMOIQ amp T1 ag uonusy i osuvIO Bi J JOOIUNS SMOPUTAA BSOTD OME 0 MO E E E E m E pa 8 S t Tm 5 B L E z o E n B 48 D 3 E zE e 5 o Tonuoo SWS eno MICROPHONE Black White 12V CAT ems WAS S JonUOS SWS pino In the saloon of the vehicle the module should be placed in hard to reach place The device should be mounted in a place protected from impact of humidity or other materials causing corrosion as far as
21. OM V 12V COM COM COM COM COM NC Tamper Tamper2 Tamper3 ARM DISARM Any accsess O O O C COM Module configuration blank sample for this diagram you will find after installing configuration program SERA located in the directory ConfigTemplates File name GTGPS v1 Boat MobileCamper tcfg 17 6 Vehicle s GSM GPS messages system Installation manual and connection diagram The module may be installed in all vehicles with petrol and diesel engines and 12V batteries negative pole of which is connected to car body The system should be installed in a saloon of vehicle following installation manual of the manufacturer The module may be installed in line with already available security system such as GSM SMS pager or as independent separate system for car protection Connection diagram of the module as independent protection system is see below Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 27 MICROPHONE E EL EEEHELHELEREHEHEL Green Yello Black White Green Yello amp isle 215 as E ols EV 5 Black 8 21818 2 S 2 pE J z me C en latin E GND aW 2 M Car Battery Y Black White Temperature sensor Turn Lamps FY 7 Sa o Turn Lamps V t 12y FUSE 5A FUSE 15A 12V g o 5 a sl gN 2 E i S Q E 5 Ignition Cut 40A 12V E 60 EG 4 GND Out remote control Ignition e 7 g B o E
22. Topkodas UAB Topkodas Up to date Add On vehicle alarm system with GSM GPS SMS DIAL Automatic Vehicle Location and Tracking User s guide Prog Version GTGPS v1 APPLICATION The module may be applied for remote monitoring and control of vehicles motorcycles boats or other transport facilities as well as for their protection via GSM network Vehicle GPS tracking by transferring info via GSM network in a form of SMS Remote control of vehicles via GSM network Temperature and voltage control Remote voice listening FEATURES Built in GPS module GPS location request via SMS GPS SMS message format including link to Google Maps You only need to press the link in your smart phone and you will be able to see vehicle location on Google Maps Geofence alarm Over speed alarm Up to date Add On ARM DISARM control of alarm system Not necessary additional desk The module may turned ON OFF by using manufacturer s central lock 6 inputs Fully programmable zones 2 inputs for arm disarm the security system The module can be controlled using standard central lock of a vehicle or using other access control device 4 programmable outputs for remote control or for fulfilment of selected function 1 output for monitoring of system s state LED indicator 16 users who receive information about protected object Reception of information in a form of SMS or via DIAL short call 400 users being able to control gate or
23. ameters 60 none TelNo 001 000100 User telephone number end symbol user ID number from 001 to 400 dial mode 0 off or 1 on sequence OUTI OUT2 OUT3 ARM DISARM MIC Delete selected user s telephone number according to ID number User ID from 001 to 61 none 001 400 62 none Delete all telephone numbers of remote control users from 001 to 400 Send via SMS a part of information regarding configurations of the module 1 05 12 command code parameters will be sent 2 21 28 command code parameters will be sent 3 31 38 command code parameters will be sent 80 none 1 4 40 49 command code parameters will be sent 5 make the request about output states Out 1 Out 4 6 test request 7 system state request input output states will be sent along with current state of the system ARM DISARM 90 123456 654321 To change installer s INST code recommended to change before applying the module in operation 91 123456 948921 To change user s USER code recommended before applying the module in operation 92 none none The module reset Reset by using SMS message Examples of typical programming messages 1 Programming of users telephone numbers to send SMS and to make a call INST 123456 01 37011111111 01 123456 installer s code 01 command code programming of users numbers user s telephone number without comprised of country code operator s code and user s telephone number the end symbol 01 use
24. as It 21 03 none Delete telephone numbers of all users 05 1 4 Several Lock Unlock modes are available 0 1 2 3 4 5 6 see diagrams in the annex No3 06 24 01 Periodicity of communication test from 00 am to 00 pm 00 no test In the example test to users will be send each hour 07 1 0 LED indication Test Reg 1 on 0 off 08 11111121 02111133 Input IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 modes 0 delay 1 interior 2 instant 3 24h 4 silent 5 fire 09 11111221 02111111 Input IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 types 0 NO type 1 NC type 2 EOL 10 1111 0011 Service messages Arm Disarm Reset Test 1 ON 0 OFF In the example service messages Reset and Test will be sent Input triggering IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 1 ON 0 OFF E ae SUMI The example demonstrates triggering of IN6 IN8 IN9 inputs Input restores IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 1 ON 0 OFF a 11100001 IONO ON In the example inputs IN1 IN3 IN5 IN6 IN8 IN9 will be restored 21 Alarm Luggage Luggage INI input name changing up to 16 symbols the end symbol 22 Alarm Bonnet Bonnet IN2 input name changing up to 16 symbols the end symbol 23 Alarm Doors Door IN3 input name changing up to 16 symbols the end symbol 24 Alarm Microwave MD INA input name changing up to 16 symbols the end symbol 25 Ignition On Ignition INS input name changing up to 16 symbols the end symbol 26 Siren on Siren IN6 input name changing up to
25. ck Unlock condition is used when a user does not want the security system to be activated deactivated by using door lock or central lock button In such event the module will analyse signals from door and central lock and will not allow changing ARM DISARM mode This feature will protect a vehicle from disabling DISARMing the module via the lock or button in the event of breaking window and pressing central lock button or lock spinning For lock unlock blocking condition it is necessary to use IN4 or and IN6 module inputs These inputs are configured like additional input function The following conditions might be set e Unlock Blocking condition e Lock Blocking condition e Lock Unlock Blocking condition V GTGPS GTGPS ss o gt V UnLock Condition r Door lock UnLock Condition Poor oes contact for contact or Unocking hk Unocking 3 Central lock switch iL es contact in passenger E Central lock switch compartment A contact in passenger for Unlocking Pull U al compartment for Unlocking Lock Condition tte V Door lock 7 contact Lock Condition for locking Door lock 5 contact o i for locking x Central lock switch 1 contact in passenger compartment for locking X Central lock switch 5 contact in passenger 4 compartment V for locking cea V Lock signa Lock signal Pull Up jaa RT UnLock signal Unlock 25 UnLock signal n Ea k 1 9 5 Automatic arming
26. cking system using GPS GSM www topkodas lt 25 SERA GTGPS configuration lol x File Setup Devices Update Help r System Options System Options GSM Communications GSM Remote Control GSM Alarm Pager GPS tracker AVL Outputs Inputs Installer password 6 symbols ieee ode Service SMS Text karaat Custom SMS Text User password 6 symbols HY Testing and Diagnostic Test time p Resettest counter after arming Boot Lock Unlock Mode 1 V Pulse using Lock and Unlock inputs sy Entry Delay f s d Exit Delay o s CTGPS Siren time i20 s JV Siren signal on amp RM DISARM T zi Celcius E Auto reARM f D v Indication on off energy saving PC time 2010 09 19 17 33 14 cows Connected 7 17 4 Installation of the product and connection diagram The module should be installed in a location ensuring GSM and GPS communication It is necessary to properly select a location for GSM antenna GSM antenna can not be hidden deeply in metal constructions to prevent GSM communication screening GSM antenna should be mounted as fa as possible from electronic sensors shock microwave microphone temperature sensors etc because GSM electromagnetic field may disturb operation of sensors or other electronic devices We are not liable for disturbances related with your GSM communication service provider Connection diagram is available in the annex however other connectio
27. cognize user s number and will automatically cancel the call Not recognized numbers are being ignored Information on how to program the user numbers is available in the description of SERA 9 2 ARM DISARM by sending SMS message Itis possible to ARM DISARM of the module by sending SMS message and using USER or INST password Example of SMS message e Deactivate the system USER 123456 59 0 e Activate the system USER 123456 59 1 More info see 17 2 9 3 ARM DISARM by using Lock and Unlock inputs It is possible to ARM DISARM the module by using Lock and Unlock inputs These inputs may be used when it is necessary to control the module via any additional external access control device having NO or NC output e Vehicle s central lock signal e Access control device e g RFID IBUTTON keyboard e tis possible to use switch button reed switch etc for generating of control signal Several Lock Unlock modes are available e Mode 1 V Pulse using Lock and Unlock inputs Lock input sets ARM mode after pulsing or steady signal Unlock sets DISARM mode It is comfortable to use Ist or 2nd mode when connecting the module to the central lock of vehicle Central lock mostly generates lock and unlock signals with two wires e 2nd mode 2 V Pulse using Lock and Unlock inputs similar as 1 mode only inverted e 3rd mode 3 V Level using Lock input used only one Lock input Unlock input is not used These modes are comfortable to use when activating
28. command USER123456 80 7 The first of two SMS System voltage State ARM clarification system state Inputs In0 Luggage closed Clarification state of the first input In1 Bonnet closed Clarification state of the second input In2 Door closed Clarification state of the third input In3 MicrowaveRestore Clarification state of the forth input In4 Shock restore Clarification state of the filth input The second of two SMS Inputs In5 Ignition OFF Clarification state of the sixth input In6 Siren OFF Clarification state of the seventh input In7 Batery restore Clarification state of the eighth input In8 Temp restore Clarification state of the ninth input Output states Outl OFF Clarification state of the first controlled output Out2 OFF 3 Clarification state of the second controlled output Out3 OFF I Clarification state of the third controlled output The module is considered to be installed properly and communication is reliable if all messages and calls are received properly and all user command are being executed properly 17 3 Configuration of the module via PC The module may be configured and tested via PA by using standard miniUSB cable This configuration is being performed by using the software SERA which you may download at www topkodas lt More info about the module configuration by using SERA program see SERA description Automatic Vehicle Location AVL and Tra
29. d in configuration 16 Remote control of the module via SMS messages or via short call With the help of SMS messages it is possible to control devices connected to outputs Outl Out2 Out3 Out4 It is possible to ARM DISARM the security system Control command for user USER are available in the table No 2 The amount of users when controlling via SMS is unlimited Example of control command when changes the states of all three outputs and inquiry is made to send information via SMS about output states after changing of output states USER123456 51 52 500 123456 user code 51 changing of the first output state 52 changing of the second output state 53 changing of the third output state 80 information request command see table No 3 5 to send information via SMS about output states More examples of controlling via SMS message see the chapterConfiguration of GSM communication module via SMS modules All outputs may be controlled via short call the module will automatically ignore the call Up to 400 users may control the module All users optionally may control outputs Outl Out2 Out3 OUT4 ARM DISARM the security system and activate voice listening MIC It is possible to assign to each user that he is able to control This is comfortable to use a single module for controlling of few gates when several masters are 17 Preparation to operate Before or after installation of the module it is necessary
30. deactivating the system by using switch or other access control device Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 9 e 4th mode V Level using Lock and Unlock inputs similar as 3rd mode is only inverted e 5th mode V 500ms Pulse Lock input uses only one Lock input Unlock input is not used The ARM DISARM state might be changed via voltage pulse longer than 500ms The voltage pulse might be generated by using switch or other input control device e 6th mode V gt 500ms Pulse Lock input similar as 5th mode is only inverted 1 2 3 4 5 6 see diagrams in annex 2 Lock and Unlock inputs do not have built in Pull Up resistor When there is no external signal you need to connect external 2 2K pull up resistor The resistor should be connected between power supply positive terminal V and input Such event may occur when switch is connected between lock input and ground as shown in Fig 91Fig 91 Example of wiring diagram with two switches One switch for ARM ing another DISARM ing Ist or 2nd modes should be set by using two switches V Pull resistor i 2 KP Ups edidi Pull resistor 2 Ik 2 Uu od sviti Fig 91 Example of wiring diagram with central lock of vehicle see annex 1 Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 10 9 4 Using Lock Unlock inputs with IN4 IN6 inputs with lock unlock blocking condition Lo
31. ed calibration of temperature sensor Temperature measurement range from 40 C to 80 C Measurement system Fahrenheit Celsius Measurement scale 0 1 C 0 18 F Module control ARM DISARM of the security system via LOCK UNLOCK outputs 6 control algorithms via SMS message via short call DIAL Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt Automatic periodical test Test sending in a form of SMS message Sending communication control messages tests at time range from 1 to 24 hours after pressing RESET button or after entering into ARM security mode Settings discreetness one hour Power supply voltage Nominal power supply voltage 12 6 V Power supply voltage range 9 16 V Consumption current In standby mode GPS receiver is OFF less than 30 mA In standby mode GPS receiver is ON less than 45 mA In dialling or SMS sending mode less than 300 mA Environmental parameters Storage temperature range from 40 to 85 C 40 to 185 F Operational temperature range from 30 to 75 C 22 to 167 F Max relative humidity under 40 C 104 F 95 Package Weis t e 430g Module weight eee e e Fe enr rea teh RR Es ee hehe rein EE 112g Overall dimensions of the module sssseeeeee 90x63x32 mm Current consumption in idle running depends on input
32. ient to use power supply source applied for power supply of security systems with the option to connect backup lead battery It is recommended to mount remote control relays into sockets Sockets may be easily fixed in metal box It is necessary to select relays according to preferred voltage and current Auxiliary BUZZER is recommended to be installed inside the premises not far from the entrance Buzzer operates together with the main siren also when the system starts calculating the time to leave the premises and the time Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 26 till alarm response of the security system after entering the premises see clause 7 1 It is possible to use buzzer of Hitpoint PB12N23P12Q or similar modified piezoelectric 12V DC 150mA max sound signalizer control device RFID iButton NC NC NC Keypad with NC or NO output gt Z a AC 110 220V x T a gt o N E 813 es e MICROPHONE Bie E Li g e le E E a fe E ic D E E E s a 2 z ola 1 g 8 5 8 zB BEBE a F2 fon 2 a P2 z OD mlalo g Black EW External oO i power supply N Temperature sensor Black White i 5 t E x x 5 a a a A v oO D E 9 2 U 2 oO E BUZZER Son SOE Sos Bos Bos M N Sa mE amp 5 din d o B Ble Ble BAE BAE BAS 3 S 5 e ja al jo Ts J a V e 7 pM sd 12V a api E BELL interior x x x x x C
33. ina Clear All 7 Ng Clear All Iv INS INS IV ING v ING 8 3 Remote control Users who are able to control the module v System Voltage System Voltage via short call v Temperature Temperature EG n i jv ARM ARM The number of users up to 400 These users are able to control IPSAM mios outputs via short call to activate voice listening and to activate V Service Service ARM DISARM mode of the system Action of the user is free to select ud Ln v GPS cps The actions to be done by the module after the telephone number having been recognized might be assigned to every telephone number OK The following actions may be selected regarding telephone number 9 of each user e To activate outputs OUTI OUT2 0UT3 OUTA optionally This function might be used to lock a vehicle s ignition to start a vehicle and for remote control of other equipment e ARM DISARM security system e Activate voice listening via external microphone MIC 9 ARM DISARM of the module The module can work in ARM mode and DISARM mode ARM DISARM state of the module may be changed thus via short call via SMS message and by using Lock Unlock inputs All modes of ARM DISARM may supplement each other For example The module may be activated via Lock Unlock inputs and deactivated via short call or SMS message 9 1 ARM DISARM via short call It is possible for 400 users to activate deactivate the module via short call The module will re
34. iren OUT2 remote control OUT3 light signalling device FLASH OUT4 ARM state e 80 command see table e 4 will send 40 49 parameters of command codes 9 Module control modes ARM DISARM see diagrams in the annex 2 INST123456 05 1 e 123456 installer s code e 05 command see table e lock unlock modes of the module see diagrams in the annex 2 172 Table of users codes no g Command Beginni Password 8 i parameters Possible Clarifications ng S default commands Q settings 1 OUT1 2 OUT2 3 OUT3 4 OUT4 Change state of selected 50 none 1 23 4 OUT output Output state changes every time after sending command code Explanation see below the table 51 none Oorl Activates or deactivates OUTI output 0 deactivates 1 activates 52 none Oorl Activates or deactivates OUT2 output 0 deactivates 1 activates 53 none Oorl Activates or deactivates OUT3 output 0 deactivates 1 activates 54 none Oorl Activates or deactivates OUT4 output 0 deactivates 1 activates 1234 1 2 3 4 selectable output number 5 Hone ul delimiter Time in seconds Time delimiter ARM DISARM command 0 DISARM the security system 1 59 none Oorl ARM the security system GPS Module control 0 To turn of GPS receiver JU none 042 1 Toturn on GPS receiver 2 Torequest GPS location with Google maps link USER 123456 3 Torequest GPS parameters 4 To request Geofence On ARM
35. mable Voltage measurement may be calibrated additionally 10 5 Temperature sensor input IN8 Temperature sensor is connected to the system wire contacts 9 Temp and 19 Temp Temperature input number in Inputs configuration table is IN8 Alarm and restore temperature may be changed Upon temperature alarm the module will send SMS message to a user And if setting exist the module will switch the selected output It is comfortable to use this function for indoor heating management In a case of accuracy shortage temperature sensor may be calibrated additionally Following the equation Temperature X ADC Y and by selecting X and Y coefficients Temperature calibration may be performed in software SERA in testing window It is necessary to have accurate thermometer in order to measure temperature at least in two points In testing window to read temperature ADC indications in these points Following the equation Temperature X ADC Y to calculate X and Y coefficients Calculated X and Y coefficients should be programmed in the module It is easy to calculate X and Y coefficients in MC Excel by using trendline 40 y 0 3284x 269 26 Teperature 80 00 820 00 840 00 860 00 880 00 900 00 920 00 940 00 ADC Temperature may be measured in Celsius and Fahrenheit 10 6 Microphone and voice listening The microphone may be connected to the system wire contacts 10 MICP and 20 MICN In orde
36. mation GSM communication strength system car battery s power supply voltage temperature and IMEI of the module GTGPS module is deal for remote vehicle start The module compares incoming number with programmed users numbers and in a case of compliance activates an output or other action and interrupts the call automatically All parameters of the module should be configured via PC by using software SERA or in remote manner by sending appropriate SMS including password The module is used for automatic vehicle tracking and determining its geographic location It is possible to see a location of a vehicle in Google Maps 3 Used definitions and terms e GPS Global Positioning System global system for determining a geographic location e Installer a person provided with INST installer s password e User a person provided with USER user s password e Authorized user a person whose mobile phone s number is entered in GSM module Two authorized users with the same rights may be entered into the module e Configuration programming of the settings which will define the operation of the item For example user s telephone numbers set up of periodicity for sending SMS message input names etc e Event event a user receives the information about e ARM status of the security system The module is in ARM mode e DISARM status of the security system The module is in standby mode only 24h inputs are active e NO input
37. ng disarming the security system The siren will generate confirmation signal when arming disarming the security system if function Siren signal on ARM DISARM was selected in the software SERA When the security system is to be turned in ARM mode the bell will beep once when in DISARM mode the bell will beep twice 10 Module inputs GT GPS module has e 6 programmable external inputs zones e temperature sensor input e Measuring of power supply voltage Internal input is visible in programming table e 2control inputs Lock and Unlock see clause9 3 Each input may be linked with selected output i e to switch selected output depending on output state This feature enables to apply the module for premisses automation and temperature control For example For example if temperature drops below the standard limit the module is able to automatically activate heating system and also to inform a user about critical temperature by sending him an SMS 10 1 Equivalent input diagrams Equivalent 1 4 input diagram a GTGPS i IN1 IN4 al 5 6 inputs are used when Pull Up resistor is not necessary for the input For example when signal should be taken from vehicle s bell or ignition or from other device for which extraneous signal cannot be applied These inputs do not have internal Pull Up resistor Input resistance is 22kOhm Equivalent diagram of 5 6 inputs 10 2 Sen
38. ng of the security system via IN6 input Force ARMing function 11 9 7 Blocking ARM INS additional feature ennemi nren nennen nre nre 11 9 8 Bell confirmation signal by arming disarming the security system sese 12 MEIN ww 12 10 1 Equivalent input diagrams oerte rnt eor cecedeessesaness vessdedscenssaeeceencetecaasbestverseeitessesdieviesensess 12 10 2 SENSO COMMECHION diagrams S 12 10 3 Input Configuration parameters eren ett reo penne re E EEEE iLE EEE EREE EEE SEEE ES EERTE ES 13 10 4 Voltage measuring IN7 internal eiee ee eri ui ere Ein Ee AEE EE VE ES EEr E A EEEn kE 14 10 5 Temperatiire sensor mput INS vc s ieccsctestssnssecesctsceeschesedecsecsncounebabisasessdteasassedscseacntuasehsbdscoedelenesussedeasvacetansans 14 10 6 Microphone and voice listening ssesseseeeeneeneeeee nennen nennen nennen iks keveri eS Eere Eaei PEE rir k 14 ll ProprammablecOutputs 5e conet ense eese Ree tie ee re aee Une ape uacasseleetanesndeaseceteuysvabbidancdslgerseapndedseascbesbeats 14 11 1 Equivalent out put diaprais uc cs iicssascecesstivetascisceesthessdecssesntoensnibisdsecscssassesedsssvsceduoshendneoedecanssunsedsesvasesansunnd 14 11 2 Output connection Gla Prams ccsseceisesenisensscnscceecaesedesscesossessntetssseosebeasarsedsesescedvoseubnssesesseonedansedetsvasersesenss 14 11 8 Operational output parameters ccs ccccseniscssssiscsescuesede
39. ns versions are also possible Fuses are necessary In order to check operation of the module it is necessary to activate used sensors door shock sensor etc and to observe their operation The user should receive messages a about alarmed zones depending on programming If SMS messages have not been received please check GSM communication and whether the module is configured properly by sending 80 command with 1 2 3 4 5 6 7 parameters We recommend to check configurations of the module and test with the software SERA The module is considered to be equipped properly and communications is reliable if all sent SMS and calls are properly received as well as all user commands are being performed 17 5 Installation instruction and connection diagram of security system for house mini mobile cottages boats It is recommended to use standard motion fire glass breaking sensors For powering of sensors we recommend to use standard 6 8 cores single core cable for designed for installation of security system For voice signalling we recommend to use siren DC12V up to 1500mA It is recommended to connect the siren to the system by using 2x0 75 sq mm double insulation cable It is possible to supply the security system from stabilized power supply source 10 15V and not less than 1 5A It is necessary to calculate max current of power supply The current of the alarm system is the current used by sensors relays siren and other devices It is most conven
40. om 001 to 400 INST123456 62 Delete all numbers of remote control users from 001 to 400 5 Inputs programming INST123456 11 00000111 12 01101111 80 1 123456 installer s code 11 command see table 00000111 used inputs are calculated from the left to the right INI IN2 IN3 INA IN5 alarms are disabled and IN6 IN7 IN8 alarms are enabled 12 command see table 01101111 INI IN4 restores are enabled IN2 IN3 INS IN6 IN7 IN8 IN9 restores are enabled 80 command see table 1 will send command code 05 12 parameters back to SMS sender More input parameters may be changed via USB 6 Programming of input names INST123456 21 Alarmluggage 22 Alarmbonnet 23 Alarmdoor 80 2 7 Output names programming INST123456 40 37011111111 01 43 ignition off 80 4 123456 installer s code 40 command see table ignition on name of output state when ignition is on 43 command see table ignition off name of output state when ignition is off 80 command see table 4 will send 40 49 parameters of command codes 8 Programming of output parameters INST123456 48 1010 49 1053 80 4 48 command outputs inversion see table Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 22 1010 OUT 1 inverted OUT2 normal OUT3 inverted OUT4 normal e 40 command description of operation output algorithm see table e 1053 OUT s
41. ontrol AC mains failure control and for alarm of silent panic o Fire this zone is always active not depending on whether the security system is ARM or DISARM The zone generates a special siren signal with interruptions The zone is applied for smoke sensors and for fire alarm Enabling or disabling of zone alarm or restore Input speed time of the input reaction this is the time period during which changed input state should remain stable in order to let the module to register alarm or restore input state Repeat time this is the time period during which repeated event of the input will be ignored Zone action switching of selected output OUT1 OUT2 OUT3 OUT4 in the event of alarm or restore May be used for object automation For example for indoor temperature control Upon dropping of temperature will critical limit heater would be switched on automatically Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 13 10 4 Voltage measuring IN7 internal This input is visible only in configuration window of the SERA software of the module IN7 input is intended for power supply voltage control If the module is being applied for the security of vehicle it is very comfortable to follow cat battery voltage A user will always be alerted that a car battery has been charged or discharged This the car battery will be protected from full discharge or damage Alarm and restore voltages are program
42. r ID number 01 16 In this example the telephone number of 1st user is entered After the telephone number has been entered all events of the security system will be sent to a user Optional events to be send may be selected only when configuring via USB 2 Itis possible to delete telephone numbers one by one according order of priority or all 16 numbers at once INST123456 02 15 Delete user s telephone number whose ID number is 15 It is possible to select from 01 to 16 INST123456 03 Delete all 16 users telephone numbers 3 To enter user s telephone number for remote control via short call INST123456 60 3701111111 001 000100 123456 installer s code 60 command code programming of users telephone numbers for remote control via short call 37011111115 user s telephone number without comprised of country code operator s code and user s telephone number the end symbol 001 user ID number from 001 to 400 In this example the telephone number of 1st user is entered 000100 What actions should be done after making call to a user Sequence from the left to the right OUT1 OUT2 0UT3 OUT4 ARM DISARM MIC 0 active functions 1 non active function In the example the function ARM DISARM is selected 4 Delete user s for remote control via short call telephone number according to ID number or all numbers at once INST123456 61 001 Delete user s telephone number whose ID number is 001 It is possible to select fr
43. r set coordinates longitude and latitude www topkodas It Automatic Vehicle Location AVL and Tracking system using GPS GSM e Google Earth Ele Edi View Tools Add Help v Search ES Fly To Find Businesses Directions BP Fly to e g Reservoir Rd Clayville NY 54 939573 23 900020 z Q 54 939573 23 900020 OE 54 939573 23 900220 v Places H Me My Places L1E9 Temporary Places LIT Mun n v Layers Earth Gallery gt gt 2 Primary Database GVogle x Location might be determined in a smart phone The phone should be provided with the option to connect to internet via GPRS Some phones have the option to open internet directly from the message field In a message field you will need to click on the generated Google Map link and the phone will show you the object location on the map Note Internet connection fill be charged following the rates of the service provider 14 4 Geofence function This function is to inform a user that the object crossed the defined zone Geofence might be applied for e vehicle protection e vehicle control when coming in or out of the defined zone or to inform a user that object has reached the zone of defined point or left the said zone The above mentioned options perfectly suit for logistic management and protection A user will be notified via SMS that cargo has reached its destination etc The function will be executed in real time and the module will it
44. r supply is OK but the module failed to register to WDG GPS green LED REG yellow LED MOD red LED Lights continuously Note the GSM network Off Modem power supply failure or it is switched off All LEDs turn off for 15sec when resetting GSM modem of the module 7 1 Input output connector pinouts Zal EU semi ae EZ E ire colour escription Q 1 GND Black Negative supply voltage GND 11 V Red Positive supply voltage Power supply voltage 8 16V Input 1 Green Yellow 1 zones input NC NO EOL 12 Input2 Green 2 zones input NC NO EOL Input3 Yellow 3 zones input NC NO EOL 13 Input4 Brown 4 zones input NC NO EOL Input5 Blue 5 zones input NC NO EOL 14 Input6 Orange 6 zones input NC NO EOL 5 Lock Black White Input for security ARMING 15 Unlock Black Input for security DISARMING 6 OUTI Grey First output 1500mA Open Collector 16 OUT2 Green Yellow Second output 1500mA Open Collector 7 OUT3 Green First output 1500mA Open Collector 17 OUT4 White Second output 1500mA Open Collector 8 LED K Black White ARM DISARM state LED cathode 18 LED A Black ARM DISARM state LED anode 9 Temp Black White Temperature sensor input 19 Temp Black Temperature sensor input 10 MICP Black White Positive differential input of the microphone 20 MICN Black Negative differential input of the microphone 8 U
45. r to avoid noises the microphone should be mounted as far as possible from GSM antenna 400 users are allowed activating voice listening in the objects In order to allow a user to activate voice listening it is necessary in user table GSM remote control to check the box MIC Note If a user number is enabled for ARM DISARM and MIC thus after making a call to the module the state ARM or DISARM will be changed and also microphone will be activated 11 Programmable outputs The module GTGPS has 4 programmable outputs Outputs of the module may be used to switch relay LEDs siren or other sound device Current for OUTI OUT4 is 1500mA All outputs are protected from short circuit over voltage and overheating 11 1 Equivalent output diagrams OUT OUT4 outputs is open collector in terms of grounding V OUT OUT4 equivalent diagram GTGPS OUT1 OUT4 COM 11 2 Output connection diagrams Examples of output connection diagrams see below Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 14 GTGPS 1500mA GTGPS 1500mA OUT1 OUT4 OUT1 OUT4 d s L E c A oO an VT V Siren COM V COM 11 3 Operational output parameters The following parameters may be set for each output e SMS text for ON output state e SMS text for OFF output state e Output operation algorithm OUT def
46. s connection type on output state and load 7 General view of the product and layout of control devices 123 REG yellow LED see71 table WDG GPS green LED see71 table MOD red LED see 71 table MiniUSB programming connector RESET button GSM antenna connector GPS antenna connector SIM card holder of Push Push type oo VA Ro pr LEONEL NAA AB CARL DRIES ERI 9 Power supply and input output connector Indication variations External LED on the Flashes remains lit for GSM module is in ARM security mode 50ms turns off for 300ms Blinking remains lit for GSM module is in DISARM non security mode 50ms turns off for 10s Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 7 system cable ARM state Off Program error processor is out of order hardware problem or power supply failure Blinking remains lit for The module is functioning GPS has not been detected 50ms turns off after 1000ms Remains lit for 500ms The module and GPS have been detected GPS geographic turns off for 1000ms location has been detection Off The module is out of order or no voltage Lights continuously Modem has been registered to the network Flashes remains lit for Modem is being registered to the GSM network 50ms tums off for 300ms Off Modem failed to register to the network Flashes Power supply OK and the module is registered to the GSM network Modem powe
47. s e o 6 7 General view of the product and layout of control devices ssssssssssssseeeeeeeeeeeneenee nennen 7 7 1 Input output connector pinouts eeseeeseeeseeeeeeeeneeeeen nennen eene enne ne tenet ne tenete entren tren tren nr e k enne 8 8 Hp me EE 8 8 1 Control and programming of the module via SMS messages sess 8 MRBPEEGDLIUILS EE 8 B 1 2 USePuzue RU A ries ber ven sites erede ss eeu Esos Pekk eeu sabuenb rele yin ko ti Rena Sev Epson Emreb soluvoensenguosasobentoess 8 8 2 Us rs to receive SMS DIALT messages inier tete rtt nete ense tiet retro tha re EE EEE eH eae EEEN EE abe eet Eae n 9 8 3 Remote control Users who are able to control the module via short call sese 9 9 JARM DISARME of the Mod le ccs ttti coto ieee ario er t aate ete sieh LEE FE Eee SEE THER opo Chop Eoaea 9 9 1 ARM DISARM Via Short call 5 eter ettet entente Ie ied ere cites cease ierat edle stes E SE EEEE IEEE 9 9 2 ARM DISARM by sending SMS message serioen epiros rapke inter teen ue bes EERE En EEREN ENRERE EESE 9 9 3 ARM DISARM by using Lock and Unlock inputs sees een eene 9 9 4 Using Lock Unlock inputs with INA IN6 inputs with lock unlock blocking condition 11 9 5 Automatic arming of the security system Auto rearm ssessssseeseeeeeeee nennen rennen enne 11 9 6 Enabli
48. se E E IM ERE 2 5 meters CEP Acquisition Rate sensitivity Tracking i egere eR E ERU 160dBm NayipatiOnis ssec e IIR HORE IEEE 157dBm dn m ae adie ik ieee HAS AA 144dBm IJhelidC c L A Mem 515 meters sec 1000 Knots max Protocols RR RR NMEA 3GPP 5 Hz position update rate capability Outputs OUT max current V 1500 mA OUT2 max current V 1500 mA OUT3 max current V 1500 mA OUTA max current V 1500 mA All outputs can be controlled via short call DIAL or via SMS message This feature may be used for gate opening ignition locking etc Output alarm parameters may be programmed Programmable algorithms for outputs operation CTRL SMS DIAL SIREN BUZER ARM state Zones OK Light Flash inverting pulse mode INI IN inputs SMS text for input alarm and restore Programmable enabling or disabling of inputs Input type NC NO EOL Algorithm for zones operation delay interior instant 24 hours silent fire Response time Time of additional response Commutation of selected out put IN7 voltage control internal power supply voltage input Alarm voltage programmable Restore voltage programmable Programming based voltage calibration Power supply voltage range from 8 0 V to 16 V Measurement scale 0 01V INS temperature control parameters External temperature sensor Alarm temperature programmable Restore temperature programmable Programming bas
49. self perform the data analysis Having read the coordinates the module checks whether they are at the range of defined zone and if they are or if they are not sends messages with the text defined in advance To activate Geofence please set the following parameters e Select Geofence operation mode e Set zone centre coordinates e Set zone radius We do not recommend to use a small radius because in the event of low GPS signal Geofence area might become even smaller than GPS accuracy can be provided When PDOP HDPO VDOP values are high 7 10 Geofence radius should be more than gt 100m Area Center Lattitude s 33865 Radius roo Reaction Time s Geof ence alarm 0 of Geofence Area alarm Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 18 14 5 Automatic dynamic Geofence activation together with ARM Geofence On ARM This feature is comfortable because it is not necessary to every time set Geofence coordinates because the module each time when ARMING will set its coordinates and will automatically activates Geofence security with a set radius Such security will inform a user in the event if a vehicle will cross a security zone In the event of burglary if a vehicle will be towed out of protected zone the module will sent Geofence alarm This feature is comfortable because it is not necessary to each time set Geofence coordinates The module will each time when ARMING set its
50. sers 8 1 Control and programming of the module via SMS messages 8 1 1 Installer Installer is able to execute all INST commands available in the table 7 The installer is able to change parameters of the module only with INST password 8 1 2 User User is able to execute only user s USER commands available in the table 72 A User may send SMS request any time and receive parameters of the security system zones and inputs states communication strength temperature Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 8 etc SMS messages may be used to control outputs Outl Out2 Out3 Out4 and to activate ARM DISARM mode A User is able to control the module only when using USER password USER 1 Communication Settings x Please note that all phone numbers must start with a country code area code phone For example 4477511111111 8 2 Users to receive SMS DIAL messages USER Phone Number The number of users up to 16 These users are able to receive anm messages or and calls after alarm response of the security system or communication test or system state test messages which are being generated after alarm response of the security system or following test sending sms calarmRestore Dialing to USER Alarm Restore messages schedule The number of users up to 16 See 81 on how to ud pem ie marr IN define types of messages to be sent to different users Ra 4 e v
51. sor connection diagrams Sensors may be connected following 4 different connection diagrams e NC normally closed contact e NO normally open contact e NC EOL normally closed with end of line resistor line resistor e NO EOL normally closed with end of line resistor resistor NOTE All resistors should be 1 kOm 10 The length of wires for connection of sensors can not exceed 300m and resistance of wire connected to sensor contacts can not exceed 300 Ohms Resistors should be mounted as near the sensor as possible Improper connection of resistors system will not work properly Pull Up resistors should be 2 2 KOhm Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 12 V V A A Pull Up resistor Pull Up resistor 2 2K 22K IN1 IN4 INS N6 4 INIMIN4 IN5 IN6 l S R i 4 NC NC NO NO COM COM COM COM d 2y Pull Up resistor Pull Up resistor 2 2K 2 2K IN1 IN4 IN5 IN6 INI INA IN5 ING6 Q t ji X NC EOL NC EOL p N IK N IK NC EOL CoM COM 4 co a UN 1K 1K 10 3 Input configuration parameters LE x rem z Zone Definition No Zone Type poor opened Alarm SMS Text poor closed Restore SMS Text Zone Options v Alarm Enabled Zone Speed f200ms ms v Restore Enabled Event Repeat Timeout 6
52. sseesnssensesbssisesscdsosansedscsvscedeoveusrdndoebsedncsnsedstovasesansann 15 12 Lumersof the security Sy Sten uestre ettet teret n Ee rene ee to ehe E SEERE e hehe LE es eet Lr ah enden Ene S bee Erase ee eau 15 13 Automatic periodical test sending nennen nnne EEEE ren eene enne CESEN EEES tren trennen 15 14 GPS USset s BUIde utere reete ere iie ose A e De ude eet ba leap eee te Mti eere e tee e Enea ea ED RR 15 14 1 GPS SMS commands requests and management sssesesssseeeeeenerenereneeeee eee 16 14 2 GPS location request via short call essere a enne E tren trennen rennen 16 14 3 Vehicle tracking and determining of geographic location by using Google Maps or Google 17 144 Geofence function ener e nU orte HIE EE EE e HORIS rete 18 14 5 Automatic dynamic Geofence activation together with ARM Geofence On ARM sees 19 14 6 GPS receiver testing and preparation to Operate eee eee ceeceeecesecesecesecsaecaeecaeecaeseaeeeeeeeeeeeeseeeeseseaeeaees 19 15 Messages Sending 3 ceo eee eget ot i E poter OE petu rete d ter 19 16 Remote control of the module via SMS messages or via short call seeeeeeeeenen 19 17 Preparation to operate aee pedes ee geeteho isee Re Tee eO ep Rr retired urn 19 ILI SIM catdi e eene pite itte eigene eee i e e ree gh 20 17 2 Configuration and control of GSM communication module via SMS messages
53. st Upon sending command SMS USER123456 80 6 test message will be sent to the number from which SMS message has been sent Below see the example of received test SMS message Test Signal strength 17 System voltage 13 16V Temperature Res 426 1 C IMEI 356895030001799 HW GTGPS SW GTGPS v1 100801 Clarifications Signal strength Numerical values of communication signal level Corresponds the following meanings according GSM telephone 0 very weak signal communication loss limit 1 5 very weak signal correspond to one bar on the monitor of a mobile phone 6 9 satisfied signal correspond to two bars on the monitor of a mobile phone 10 14 good signal correspond to three bars on the monitor of a mobile phone 15 and more excellent signal corresponds to four bars on the monitor of a mobile Voltage Voltage of car battery or other power supply source the module is connected to Temperature Res temperature sensor s showings C or F IMEI IMEI number of GSM modem HW hardware version SW software version Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 24 System state request according to the command USER123456 80 7 e 123456 user code e 80 command see table No 3 e 7 command system state request The module will sent two part message to the number the SMS was sent from Below you will see the example of received SMS message following request
54. state Periodical GPS coordinates sending P1 time interval to send the coordinates 1 9999min delimiter ay none Nee P2 Number 1 9999 how many SMS GPS coordinates will be sent to a user delimiter Send via SMS a part of information regarding configurations of the module 1 01 12 command code parameters will be sent 2 21 28 command code parameters will be sent 3 31 38 command code parameters will be sent 88 done LES eg 4 40 49 command code parameters will be sent 5 to make a request about output states Out 1 Out 4 6 test request 7 System state request will send information on input output states and system state ARM DISARM Outputs control via SMS messages Output states of the module may also be controlled via SMS messages Let s assume that vehicle ignition should be blocked thus the first output should be connected to ignition blocking relay For outputs control the following commands are used 50 51 52 53 54 58 Command 50 changes inverts state of selected output When this command is being sent output state is being changed i e if output has been deactivated it is activated and vice versa 51 52 53 54 commands sets preferred output state if O is being sent the output is being deactivated if 1 the output is being activated 50 and 51 52 53 54 commands performs the same action i e changes output states The user may use command which are the more
55. telephone number the command was sent from To activate Geofence security according to current object state USER123456 72 0 123456 user code more info see 8 1 2 space character 72 command see table 172 space character 5800 Geofence circle radius figure end character According to this example the command will be assigned to the module to set its GPS geographical coordinates according to which Geofence centre and radius will be defined The same may be done with configuration program see chapter 4 4 14 2 GPS location request via short call GPS geographical coordinates may be acquired when making a call to the module if your telephone number is entered and the setting to acquire GPS information is checked When dialling the module will automatically hang up a call and will send a message with geographic coordinates to the phone the call was made from The format to send GPS coordinates might be set in SERA program Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 16 Note If this function is active a user will not be able to enable a microphone because the call will be automatically terminated 14 3 Vehicle tracking and determining of geographic location by using Google Maps or Google The object location on a map may be set by using PC or smart phone e Jn both cases firstly one should order vehicle s geographic location via SMS or short call To open internet browser
56. that the object crossed the defined zone The zone covers the area in a defined radius around the set point e Ifthe function of periodical GPS location sending is assigned to preferred users Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 15 14 1 GPS SMS commands requests and management The list of SMS commands and parameters see in the tables 171and 172 Sleep mode of GPS received energy saving mode USER123456 70 0 123456 user code more info see 8 1 2 space character 70 command see table 172 space character 0 disable GPS receiver To activate GPS receiver USER123456 70 1 To send GPS location with Googpe maps link USER 123456 70 2 Example of received SMS http maps google com maps q 54 933573 23 904220 To send all parameters of GPS receiver USER 123456 70 3 Example of received SMS Long 54 933590 Lat 23 904348 Altitude 107m Speed 1 1km h PDOP 1 80 Sat in Use 9 Sat in View 12 Geofence 2 505km UTC GPS Time 09 26 2010 18 16 38 Automatic object tracking according to SMS request USER 123456 71 3 500 123456 user code more info see 8 2 space character 71 command see table 172 space character 3 to send GPS location every 3 minutes figure end character 500 to send 500 SMS with geographic location figure end character According to this example the amount of 500 SMS including geographical coordinates will be sent every 3 minutes to the
57. the module USER User This verifier is used for module control e Installer s or user s password e Command code e Configuration kit One SMS message may include as many commands as one SMS message may cover i e 160 symbols including spaces In such case firstly verifier should be sent password should be written without space after the verifier and further come command code parameter command code parameters etc separated with space The module executes the commands as follows the first command next after the password and further go all other commands from the left to the right 171 Table of Installer command codes a 8 Command Examples of command E 1 E parameters default parameters Clarifications QE settings examples Telephone number of users to whom send SMS and to whom make a call DIAL up to Ep 01 none TelNo 01 16 symbols the end symbol after the symbol user priority number 01 16 should A be entered E Delete selected user s telephone number according to priority number User ID from 01 02 none 01 to 16 Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 20 Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkod
58. to configure its parameters SIM card settings may be configured by using only GSM phone How to prepare the module to operate e Connect system connector GSM and GPS antennas e Connect power supply source 10 15V battery or stabilized 10 15V 1A power supply source e Check and if necessary enter SMS message centre number using GSM phones Mostly SIM card already has SMS centre number inserted please skip this step Automatic Vehicle Location AVL and Tracking system using GPS GSM www topkodas lt 19 Remove PIN code request of the SIM card using GSM phones Install SERA configuration program Connect USB cable to the PC and to the module Launch SERA program Guidelines on how to use SERA program is available in SERA description GSM communication strength IMEI and SMS centre number are available in Test window see SERA description Configure telephone numbers to which information should be transferred Set the numbers to send SMS and to make a call Set active inputs which will be used For example if the input will not be used it should be disabled Set periodicity of communication test if 00 is entered the test will not be send Set input parameters e Setoutput OUTI OUT2 OUT3 OUT4 states if applied After inserting SIM card or upon changing parameters of the module it is necessary to press RESET button There are two types to configure the module The first via SMS messages The second via PC by connecting

gtgps user manual

Contents

Download Pdf Manuals

Related Search

Related Contents