Table of Contents Pdf

Home

1. 006 WARRANTY AND SERVICE 1 Safety Precautions and Warnings To prevent personal injury or damage to vehicles and or the scan tool read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle Always perform automotive testing in a safe environment Wear safety eye protection that meets ANSI standards Keep clothing hair hands tools test equipment etc away from all moving or hot engine parts Operate the vehicle in a well ventilated work area Exhaust gases are poisonous Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests Use extreme caution when working around the ignition coil distributor cap ignition wires and spark plugs These components create hazardous voltages when the engine is running Put the transmission in PARK for automatic transmission or NEUTRAL for manual transmission and make sure the parking brake is engaged Keep a fire extinguisher suitable for gasoline chemical electrical fires nearby Don t connect or disconnect any test equipment while the ignition is on or the engine is running Keep the scan tool dry clean free from oil water or grease Use a mild detergent on a clean cloth to clean the outside of the scan tool when necessary 2 General Information 2 1 On Board Diagnostics OBD II The first generation of On Board Diagnostics called OBD I was developed
2. 1 From the diagnostic function menu Figure 11 26 use the UP DOWN scroll button to select Module ID Information and press the OK button 2 View module information present with its IDs and part numbers 105 3 Module ID Information End Model Part 0 Number Base Model Part 2155905152 Number Software Part Number 255 Calibration Part 4294967295 Number Save Esc Figure 11 35 Select Save to store the module ID information or press the ESC button to exit without saving If the vehicle does not support SRS communication an advisory message shows on the screen Press ESC button to return to the previous menu 106 12 SAS Steering Angle Sensor Calibration Steering Angle Sensor Calibration permanently stores the current steering wheel position as the straight ahead position in the steering angle sensor EEPROM Therefore the front wheels and the steering wheel must be set exactly to the straight ahead position before calibration In addition the vehicle identification number is also read from the instrument cluster and stored permanently in the steering angle sensor EEPROM On successful completion of calibration the steering angle sensor fault memory is automatically cleared Calibration must always be carried out after the following operations Steering wheel replacement Steering angle sensor replacement Any maintenance that involves opening the connector hub from the steering angle sens
3. DTC Lookup D Only PCBU can be the first letter to be put in Only 0 9 a f for the rest letters Finish Show Figure 6 39 3 Select Show and a soft keyboard will pop up Use LEFT RIGHT button and UP DOWN button to move to the desired character then press OK button to confirm 4 After you input the DTC code select Finish and the scan tool will ask for your confirmation 4 Input Dialog Box P0005 Do you want to save and continue Figure 6 40 5 Press Yes or OK button to proceed The scan tool will display DTC definition as below 56 4 Trouble Codes P0005 Fuel Shutoff Valve A Control Circuit Open Figure 6 41 e Use the LEFT RIGHT scroll button to view the previous next DTC e Select Save to record code definition e For manufacturer specific codes you need to select a vehicle make on an additional screen to look for DTC definitions e Jf definition could not be found SAE or Manufacturer Specific the scan tool displays Please refer to vehicle service manual 6 Press No or ESC button to return to previous menu 57 7 Print Data The Print Data function allows printing out diagnostic data recorded by the scan tool or customized test reports by connecting the scan tool to a PC or laptop with the USB cable supplied e To print out retrieved data you need the following tools MOT Pro scan tool A PC or laptop with USB ports A USB cable 1 Install Autel PC Suit
4. NOTE AUTEL accepts no responsibility for any accident or injury arising from servicing the ABS SRS systems When interpreting DTCs retrieved from the vehicle always follow the manufacturer s recommendation for repair NOTE All software screens shown in this manual are examples actual test screens may vary for each vehicle being tested Observe the menu titles and onscreen instructions to make correct option selections Please follow these steps to start the ABS SRS diagnostic testing procedure 1 Turn the ignition off 2 Locate the vehicle s 16 pin Data Link Connector DLC 3 Plug the scan tool cable connector into the vehicle s DLC 4 Tum the ignition on but do not start the engine 5 Turn on the scan tool and wait for the Main Screen to appear 6 Use the UP DOWN scroll button or LEFT RIGHT scroll button to select AbsSrs in the Main Screen Figure 3 1 11 1 Vehicle Selection There are three ways for users to enter the vehicle information in the scan tool A Select vehicle step by step 86 In this mode the scan tool will communicate with the vehicle and a series of vehicle identification screens appears for user to identify the vehicle These may include vehicle Model Year Type and Vehicle Part etc for selection On each screen that appears use the UP DOWN scroll button to select the correct option and then press the OK button Do this until the vehicle is completely identified Taking Fiat as
5. Figure 6 12 PID name current value maximum and minimum values are displayed on the screen 39 Engine RPM 812 rpm Vehicle Speed Sensor 0 km h Text Save Figure 6 12 e Ifthe Merge Graph at the bottom appears when a PID is selected to view merged graph information is available Figure 6 13 E NOTE Merge Graph can be used to compare two related parameters in graphic mode which is especially convenient in the Custom List option where you could select two interacted parameter to merge and see their relationship Vehicle Speed Sensor 0 Pause MergeGraph Save Figure 6 13 e Select Text to return to text viewing of PID data e Select Save to record retrieved live data and PID graphs e Select Pause to suspend viewing You could resume the viewing process again by selecting Start 40 3 Press the ESC button to return to previous menu B Viewing Custom List 1 To view customized PID data use the UP DOWN scroll button to select Custom List from Live Data menu and press the OK button Figure 6 10 2 Use the UP DOWN scroll button to move up and down to the desired items and click Select button to confirm The selected parameters are marked with solid squares Figure 6 14 M Numbers of DTCs 1 2 O Fuel system 2 status O Calculated load value O Engine coolant temp Select All Clear Clear all Figure 6 14 e The number to the right of selected item indi
6. At least one of the following fault codes is stored for the tested function component group 4667 480A 481A Possible causes of fault Ok Cancel Figure 13 28 4 The tool shows a list of particle filter tests as below Motor Electronics 1 Visual inspection of engine oil 2 Visual inspection of particulate filter 3 Function check of swirl flaps 4 Exhaust backpressure test 5 JActual target value check mass air flow sensor Figure 13 29 The option keys at the bottom of the screen work as below 1 Visual inspection of engine oil 2 Visual inspection of particulate filter 3 Function check of swirl flaps 4 Exhaust backpressure test 5 Actual target value check mass air flow sensor Back Return to the previous menu 1 Visual inspection of engine oil 138 a From the particle filter test menu Figure 13 29 use the LEFT RIGHT scroll button to select 1 and press the OK button Motor Electronics Check of oil and compliance with oil change interval Does one of the following conditions apply Oil level too high or too low Oil change interval exceeded Test Selection No Yes Figure 13 30 b Select No if you visually find nothing wrong with your engine oil The tool displays as below Press OK button to return to previous menu Motor Electronics No fault can currently be found in the compontent group function tested Az Figure 13 31 c Or select Yes if
7. E NOTE The screens shown below in this chapter are examples The screens actually appear vary by vehicle 5 1 Entering vehicle information Before using the scan tool to diagnose you must input the vehicle information There are generally three ways to input the vehicle information e Vehicle information manual acquisition e VIN code automatic acquisition e _ VIN code manual acquisition The way to enter diagnostic procedure depends on vehicle being tested Vehicle information manual acquisition Follow these steps to enter the vehicle information and begin diagnostics Taking Ford as an example 1 Turn on the scan tool and wait for the Main Screen to appear 2 Select Scan icon in the Main Screen Figure 3 1 and wait for the vehicle manufacturer screen Choose the correct vehicle make Asian Figure 5 1 20 a S GM V1 00 Chrysler 1 00 Ford V4 00 Figure 5 2 3 Step by step select the right options for your vehicle according to each screen that appears DAS Start New Session 1 NEG Manual Vehicle Entry Figure 5 3 Figure 5 4 4 Traction Assist Transmission 1 MOAM MEE ASM Auto Shift Manual 2 Equipped _Powershift Manual Automatic DPS6 Figure 5 5 Figure 5 6 4 Do this until the complete vehicle information is entered Then the scan tool will ask for your confirmation 21 Vehicle Specification Vehicle Mustang Engine Type Other Cap
8. Erase Codes After reading and or reviewing the diagnostic trouble codes use the following steps to erase the codes from the vehicle If Erase Codes is not an available menu option consult the manufacturer s service manual for the correct clear code method E4 NOTE This Erase Codes function clears the DTCs from the selected ECU or provides instructions for how to manually clear the codes from the ECU E4 NOTE Before performing this procedure make sure the vehicle s ignition key is in the On Run position with the engine off To Erase DTCs please follow these steps 1 With the Function Menu screen displayed Figure 5 23 click on Erase Codes The scan tool displays an instruction message 2 Follow the instructions on each screen that appears until the procedure is complete When finished press any key to exit 4 Use Read Codes function to check the codes again to see if DTCs have been erased successfully If any codes remain repeat the Erase Codes steps 31 6 Generic OBDII Diagnostics The OBD II Diagnostics function is a fast access option that allows you to carry out a quick test on the engine system of OBD II vehicles When more than one vehicle control module is detected by the scan tool you will be prompted to select the module where the data may be retrieved The most often to be selected are the Power train Control Module PCM and Transmission Control Module TCM CAUTION Don t connect or di
9. If the One Graphic option is highlighted when a specific item is selected the graphic information is available The PID name current value maximum and minimum values are displayed on the screen When the data is shown in graph the tool offers two more options Two Graphic and Merge Graph The first option can display two graphs on the same screen and the last option can merge the two graphs into one Press the ESC button to return to the previous menu Special Functions This function allows users to do various active tests or module programming The function options vary with the vehicles being tested 1 2 From the diagnostic function menu Figure 11 26 use the UP DOWN scroll button to select Special Functions and press the OK button The tool will display a list of available special functions for the vehicle being tested Use the UP DOWN scroll button to select the desired function and press the OK button Taking Chime 104 Output as an example Output Controls 1 Chime Output 2 Driver Seat Belt Reminder 3 Passenger Seat Belt Reminder Figure 11 33 3 Press the corresponding FUNCTION BUTTON ON or OFF to check whether the Chime on the vehicle is turning on or off Chime Output Restraints ID 01 Drvr Air Bag Stage 1 0 Ohms Resist Figure 11 34 E Module ID Information This function allows users to view the selected control module information
10. and press the OK button Wait for the Scan screen to appear Figure 4 1 Figure 4 1 2 To review the data saved in the scan function select SCAN in the Replay menu To review the data in the saved EPB function select EPB in the reply menu Then press OK to continue 3 Use the UP DOWN scroll button to select the desired item from Scan screen and press the OK button Scan 1 UITrouble scan MAKE USA FORD 2 UIDatastream complete list scan make EOBD 3 UIFreeze scan make USA Delete Delete All Figure 4 2 e f no data from previously tested vehicle is recorded a message No data available shows on the screen 4 Review selected data on screen Figure 4 3 Vehicle Specification Vehicle Mustang Engine Type Other Capacity 3 8L Transmission Manual Fuel Type Gasoline Emission Level Federal Emission VIN 1FAFP40462F100819 PrefSuf 2R3APB _ VersionID 4612 Figure 4 3 4 2 Deleting Data By selecting Delete on the Scan screen you are allowed to erase the selected data on the scan tool Review the recordings thoroughly before erasing You could also erase all recordings by select Delete All F NOTE Don t use Delete All unless you are definitely sure what you are going to proceed 4 3 Printing Data Print option allows you to print the recorded files to your computer and then to the printer For more details please refer to chapter 7 Print Data 19 5 Diagnostics
11. Base Model Part 36778547 Number Software Part Number 70332979 Calibration Part 87110195 Number Save Esc Figure 11 24 3 Select Save to store the module ID information or press the ESC button to exit without saving 99 e If the vehicle does not support ABS communication an advisory message shows on the screen Press ESC button to return to the previous menu 11 3 SRS Diagnostics After the vehicle information is entered correctly select SRS system to perform SRS diagnostics Take GM as an example 3 6 L LFX 1 Supplemental Inflatable Restraint 2 Electronic Brake Control Module Figure 11 25 From the ABS and SRS menu use the UP DOWN scroll button to select Supplemental Inflatable Restraint and press the OK button The screen displays as below Supplemental Inflatable Restraint 1 Diagnostic Trouble Codes DTC 2 Data Display 3 Special Functions 4 Module ID Information Figure 11 26 A Read Codes This function allows user to read the SRS DTCs from vehicle ECU 100 1 From the diagnostic function menu Figure 11 26 use the UP DOWN scroll button to select Diagnostic Trouble Codes DTC and press the OK button Diagnostic Trouble Codes DTC 1 Read DTC Information 2 Clear DTC Information Figure 11 27 2 Use the UP DOWN scroll button to select Read DTC Information and press the OK button Figure 11 27 3 View DTCs and their definitions on screen Read D
12. Cancel to go back to the list of possible operations In the third condition the tool will display an information screen as The actuator test did not finish operating Please perform the following check Read the faults to resolve any possible faults relating to the electric motor or to the cables IMPORTANT Make sure that the components to be tested are not physically damaged and are well assembled 83 E WARNING Please stop repairing the components to be tested before the test starts and keep a certain distance during the test 10 3 ABS Maintenance In the System menu Figure 10 2 use UP DOWN button to select ABS to do ABS maintenance The scan tool displays as below Diag Menu 6 Read Codes 7 Erase Codes 8 Live Data 9 Active Test 10 ECU Information 6 Special Function Figure 10 20 In the ABS diagnostic function the tool can read codes erase codes record live data read ECU information perform active test and perform special function For the functions already being described before please refer to chapter 5 OBDII Diagnostics for details Special Function 1 In the Diagnostic Menu Figure 10 20 use the UP DOWN button to select Special Function to do the ABS test The scan tool displays as below 1 Reactivation of automatic application 2 Deactivation of automatic application Figure 10 21 84 2 In the EPB menu select the desired function and press OK button If the ope
13. Codes function to verify 13 2 3 Live Data This function enables users to view DPF related data readings from a selected ECU With the live data screen displayed you can view the data in text or graphical format record and save files for later viewing pause the readings and view past data and more 1 From the function menu Figure 13 3 use the UP DOWN scroll button to select Live Data and press the OK button 122 2 3 Live data 1 Diagnosis requests 2 Cruise control 3 Particulate filter Figure 13 7 In this function list Diagnosis requests retrieves signal data generated by the sensors Cruise control shows the driving conditions and Particulate filter displays the DPF system status information Taking Particulate filter as an example Select only the PIDs that you wish to display Use the UP DOWN scroll button to move to the desired item and press the corresponding FUNCTION BUTTON Select to choose Custom list Enable regeneration Request regeneration Status regeneration amp W N Be Distance travelled since regeneration eS Exhaust gas temperature before 5 particulate filter Select All Clear Clear All Figure 13 8 The Selected items are marked with ticks on the left The number on the right indicates sequence of the selected item Press the corresponding FUNCTION BUTTON Clear to unselect items or press the corresponding FUNCTION BUTT
14. an example Version 01 100 1AV CER Diagnosis System Menu 1 BREED MY 97 Air Bag 2F 2 BREED MY 97 Air Bag 2F 2L S 3 BREED MY 97 Air Bag 2F S 4 BREED MY 97 Air Bag 2F 2L 8 1 9D 5 Teves ABS MK20 MK70 Figure 11 1 e For some vehicles the vehicle identification procedure will ask you to select a letter which indicates one character of VIN code Taking Chevrolet as an example Chevrolet Figure 11 2 87 e For some vehicles the ABS and SRS systems are divided into two systems SRS is located in Body system while ABS is located in Chassis system In this case you will need to select the correct system to run the desired diagnostics S 1 Body 2 Chassis Figure 11 3 B Manual vehicle entry This mode allows users to input and save specific vehicle information i e PCM Part Number Vehicle Calibration Number Tear Tag and VIN manually This function enables direct access to the vehicle s ABS system and makes the diagnostic testing more convenient saving time doing step by step entry selections Taking Ford as an example 1 Select the Ford logo from the car make screen Figure 11 4 88 2 Use the UP DOWN scroll button to select the Manual Vehicle Entry option from the DAS menu DAS 1 Start New Session 2 Manual Vehicle Entry 3 Vehicle selection Figure 11 5 3 To enable the scan tool to identify th
15. incidental or consequential damages arising from the use misuse or mounting of the scan tool Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you 4 All information in this manual is based on the latest information available at the time of publication and no warranty can be made for its accuracy or completeness Autel reserves the right to make changes at any time without notice Service Procedures If you have any questions please contact your local store distributor or visit our website at www autel com If it becomes necessary to return the scan tool for repair contact your local distributor for more information 158
16. outlet of the filter is accessible Is the exhaust flange at the outlet of the particle filter free of soot and are there distinct soot deposits only the inside of the exhaust tailpipe Yes No Figure 13 35 d Or select Test Selection to return to previous menu 3 Function check of swirl flaps a From the particle filter test menu Figure 13 29 use the LEFT RIGHT scroll button to select 3 and press the OK button 141 Motor Electronics Function test The following component is actuated in the next test step Swirl flap actuator at 4 second intervals Check Movement of control rod Setpoint Adjustment range 19 mm 10 4 Cancel Figure 13 36 b Select OK to activate swirl flaps and the tool displays as below Figure 13 37 Press OK button to end the activation and exit Motor Electronics Check the Movement of control rod Setpoint Adjustment range 19 mm Press OK to end activation Figure 13 37 c Or select Cancel to return to previous menu 4 Exhaust backpressure test a From the particle filter test menu Figure 13 29 use the LEFT RIGHT scroll button to select 4 and press the OK button 142 Attention The engine must be operated for at 3 minites at idle speed before carrying out the exhaust backpressure test This requirement ensures that the preconditions for the exhaust gas pressure test are met OK Cancel Figure 13 38 b Press OK button to proceed and the
17. select No to return to previous screen Vehicle Specification Vehicle Ranger Mazda B Series Courier Engine Type Other Capacity 3 0L Transmission Automatic Fuel Type Gasoline Emission Level 50 State Emission Is this correct Figure 11 9 C Auto vehicle entry Some vehicles provide an auto scan feature which allows users to skip time wasting step by step vehicle identification procedure and retrieve the specific vehicle information from vehicle computer directly F NOTE This function may not be available for all vehicles Take Ford as an example 1 Select the Ford logo from the vehicle make screen 91 DAS 1 Start New Session 2 Manual Vehicle Entry 3 Vehicle selection Figure 11 10 2 Use the UP DOWN scroll button to select the Start New Session from the DAS menu 3 A screen message with the vehicle information will come up asking for your confirmation If the information is correct select Yes to continue otherwise select No to return to previous screen Vehicle Specification Vehicle Edge Engine Type TiIVCT Capacity 3 7L Transmission Automatic Fuel Type Gasoline Emission Level 50 State Emission Is this correct Yes No Figure 11 11 After the vehicle information is entered correctly you will need to select SRS and ABS systems as below 11 2 ABS Diagnostics After the vehicle information is entered correctly select ABS system to perform ABS d
18. the particle filter in a motorway or cross country trip taking approx 30 minutes at a speed that is as constant as possible Subsequently the service function Particle filter regeneration must be run again NOTE During the regeneration phase and with the engine running it can also occur that the display for Regeneration active jumps to Regeneration not active This behavior can be seen exclusively with the vehicle stationary with the engine 136 running This behavior does not impair the scheduled course of the regeneration in general 13 3 5 Particle Filter Test It is advisable to carry out a series of particle filter tests as a result of constant DPF regeneration such as checking oil level oil change interval for diesel contamination swirl flaps backpressure sensors and particle filter soot remains 1 From the service functions menu Figure 13 11 use the UP DOWN scroll button to select Particle filter test and press the OK button 2 The tool communicates with the vehicle and reads the fault codes memory If there is no relevant fault code stored in DDE the screen displays as below Select Cancel to exit this function Motor Electronics No fault code is stored for DDE No relevant fault codes stored in DDE Cancel Figure 13 27 3 If there are DPF related codes stored in DDE the screen displays as below Select OK to continue or Cancel to exit this function 137 Motor Electronics
19. tool displays as below Or select Cancel to return to previous menu Motor Electronics In the next test step the exhaust backpressure is checked at idle speed Run engine at idle speed Figure 13 39 c Check the exhaust backpressure with engine running idle The tool will read off the actual backpressure value and compare with the upper limit Figure 13 40 Select OK to continue the test or Cancel to return to previous menu 143 Motor Electronics Compare actual value and maximum permissible value for approx 10 seconds Actual value 32 0 mbar Maximum permissible value 75 mbar To end test step press OK OK Cancel Figure 13 40 If the engine is not running at idle speed the tool will display a warning message Figure 13 41 Select OK to repeat the test or select Cancel to exit Motor Electronics The engine speed was not maintained during the test Do you wish to repeat the exhaust backpressure test at idle speed le 4 Cancel Figure 13 41 d Check the exhaust backpressure with engine running at 2000 rpm The tool will read off the actual backpressure value and compare with the upper limit Figure 13 42 Select OK to continue the test or Cancel to return to previous menu 144 Motor Electronics Compare actual value and maximum permissible value for approx 10 seconds Actual value 32 0 mbar Maximum permissible value 75 mbar To end test step press OK OK Cancel Fig
20. values exceed the limits The tool displays an instruction message as below Press OK button to return to previous menu Motor Electronics The optimum procedure for buming off the particle filter is to driver the vehicle on the motorway at a speed of 130 140 km h for 30 minutes If this is not possible or not permitted drive at alternating speeds on trunk roads or on the motorway for appox 30 A Figure 13 47 h Or select No if the actual values are within the limits then the tool will return to previous menu Motor Electronics No fault can currently be found in the compontent group function tested Az Figure 13 48 i Or select Test Selection to return to previous menu 5 Actual target value check mass air flow sensor a From the particle filter test menu Figure 13 29 use the LEFT RIGHT scroll button to select 5 and press the OK button 147 Motor Electronics The target actual value test for the mass air flow sensor can be conducted only with the aid of the Air Mass System Test Figure 13 49 b Press OK button to return to previous menu 148 14 TPMS Tire Pressure Monitor System This function allows user to quickly look up vehicle TPMS information and reset procedures and perform Tire Pressure Monitor System diagnostics With the tool properly connected to a vehicle s data link connector DLC you can use the tool to read TPMS diagnostic trouble codes D
21. viewing and saving Identification A Part number basic 7801710 control module Hardware version index 00 Variant index 19537 Diagnosis index 33 Coding index 4 Date of manufacture 22 07 2006 Save Esc Figure 13 10 3 Select Save option to save the information for later review or press the ESC button to return to the previous menu 13 3 DPF Service Functions Use the UP DOWN scroll button to select Service Functions in the menu Figure 13 2 The screen displays as below Motor Electronics 1 Starting Basic Injection Quantity 2 Injection Rate 3 Injector Rate Adjustment 4 Particle filter regeneration 5 Particle filter test Figure 13 11 13 3 1 Starting Basic Inspection Quantity This function enables you to start fuel delivery matching 125 1 From the service functions menu Figure 13 11 use the UP DOWN scroll button to select Starting Basic Inspection Quantity and press the OK button 2 The tool communicates with the vehicle and reads the fault codes memory Follow the on screen instructions to finish this procedure Motor Electronics Motor Electronics Switch o Fault codes are memory It is recommend before carrying Motor Electronics Starting fuel delivery matching makes it rocedure p possible to increase the starting fuel delivery additively by a certain amount The value is entered via the input field and the unit is m
22. 00 787 100 Pause Text Saving 70 Figure 6 17 E NOTE The scan tool can only playback text data even though the data is saved in graphic mode 2 When there is not enough memory space a warning message prompting to delete previously recorded data Save Failure Memory space not enough Erase previously recorded Data Yes Figure 6 18 e If you wish to delete the data select Yes and save currently retrieved data in the SD card e If you do not wish to delete the data select No to return to previous screen 43 3 4 5 Select Pause to suspend recording You could resume the recording process again by selecting Start You may review the saved data in Playback function Press ESC button to exit 6 4 Freeze Frame Freeze Frame Data allows the technician to view the vehicle s operating parameters at the moment a DTC Diagnostic Trouble Code is detected For example the parameters may include engine speed RPM engine coolant temperature ECT or vehicle speed sensor VSS etc This information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes 1 2 3 To view freeze frame data use the UP DOWN scroll button to select Freeze Frame from Diagnostic Menu and press the OK button Figure 6 3 Wait a few seconds while the scan tool validates the PID MAP If retrieved information covers more than one screen use the DOWN scroll butt
23. 16 use the LEFT RIGHT scroll button to select 2 and press the OK button The tool will automatically reset the value to 100 C Store data and exit When you have finished the injection volume adjustment use the LEFT RIGHT scroll button to select 3 and press the OK button to store the new value in the control units or select 4 and press the OK button to retain the old value 13 3 3 Injector Rate Adjustment This function enables you to adjust the injector rate for individual cylinders 1 From the service functions menu Figure 13 11 use the UP DOWN scroll button to select Injector rate adjustment and press the OK button 2 The tool communicates with the vehicle and reads the fault codes memory Follow the on screen instructions to finish this procedure 3 Then the tool will display as below In this function you can enter new value for each cylinder 131 Motor Electronics Adjustment values currently stored Cylinder 1 CAITEEC Cylinder 2 DANTWGD Cylinder 3 EASUEIE Cylinder 4 FAWUWLF EDIT1 Figure 13 19 The option keys at the bottom of the screen work as below EDIT 1 Edit Cylinder 1 injector code EDIT 2 Edit Cylinder 2 injector code EDIT 3 Edit Cylinder 3 injector code EDIT 4 Edit Cylinder 4 injector code Back Return to the previous menu Restore Retain the old value A Enter new value for cylinder From the Injector rate adjustment menu Figure 13 19 use the LEFT RIGHT scro
24. 23 Cars 1 Vehicle record and abbreviation 2 Select by entering VIN 3 All model series 4 A Class 5 B Class 6 C Class CLK 7 E Class CLS Figure 5 12 Select by entering VIN ees If the chassis number does not Match the vehicle enter VIN as a 17 digit code Example WDBNG70J02A123456 Finish Figure 5 13 When you choose to enter VIN directly a pop up soft keyboard is used to input VIN code Figure 5 14 To pop up the keyboard press the Function button corresponding to Show Use UP DOWN scroll button and LEFT RIGHT scroll button to select digit and character and then press OK button to confirm Use Backspace button to delete the previous digit or character When finished press the Function button corresponding to Finish to proceed The scan tool will identify the VIN code and turn to diagnostic procedure 24 Select by entering VIN O W E R Ti O RD OS a e gh A a BS IE Ge R N R E 4 6 Za A PE ECE fio e hee ABCDE SPACE 0 Finish Pre Backspace Figure 5 14 5 2 Diagnostic Test After you have entered the correct vehicle information the diagnostic testing selection will display as below Select An Option 1 2 Control Unit 3 Vehicle Information Figure 5 15 1 Auto Scan Depending on the scan tool model Auto Scan function will carry out an overall scan to check the status of all systems or four systems engine transmission airbag and ABS on the vehicle being tested S
25. 4 e Active Test This function enables you to perform actuator test for a specific component 1 From the TPMS diagnostic function menu Figure 14 1 use the UP DOWN scroll button to select the Active Test and press OK button 2 The tool will display a list of available active tests for the vehicle being tested Active Test 1 BUZZER 2 WARNING LAMP 3 HAZARD LAMP Figure 14 10 Taking Warning Lamp for example 1 From Active Test Menu use the UP DOWN scroll button to select Warning Lamp function Figure 14 10 2 Press the corresponding FUNCTION BUTTON ON or OFF to check whether the warning lamp on the vehicle is turning on or off Figure 14 11 Active Test WARNING LAMP OFF Figure 14 11 155 3 Press the ESC button to return to the previous menu Special Function This function enables you to program and reset TPMS related components or write TPMS sensor IDs to the ECU 1 From the TPMS diagnostic function menu Figure 14 1 use the UP DOWN scroll button to select the Special Function and press OK button 2 The tool will display a list of available special functions for the vehicle being tested Special Function 1 ID Regist Figure 14 12 Taking ID Regist for example 1 From Special Function Menu use the UP DOWN scroll button to select ID Regist function Figure 14 12 2 The tool will communicate with vehicle computer and register the TPMS sensor
26. BD2 Cable Provides power to tool and communicates between tool and vehicle 4 USB Cable Used to upgrade the scan tool and to print retrieved data 5 SD Card Contains the scan tool s operation software and applications 6 Carry Case A nylon case to store the scan tool when not in use 3 4 Keyboard No solvents such as alcohol are allowed to clean the keypad or display Use a mild nonabrasive detergent and a soft cotton cloth Do not soak the keypad as the keypad is not waterproof 10 3 5 Power Before using the scan tool you must provide power to the scan tool There are two methods for providing power to the scan tool e DC external power adapter e Cable connection to vehicle During vehicle testing power for the scan tool is usually provided through the vehicle cable connection When the scan tool is not connected to a vehicle the scan tool can be powered with an AC DC external power adapter While the scan tool is powered via the vehicle Data Link Connector DLC just follow the steps below to turn on the scan tool 1 Connect the Cable to scan tool 2 Find DLC on vehicle e A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the OBD2 cable 3 Plug the cable to the vehicle s DLC 4 Power up the scan tool and wait for the Main Screen to appear Figure 3 1 Rae Scan ie OBDII V1 00 EPB V1 0 ou Figure 3 1 3 6 System Setup The S
27. Data Recorder from the DAS menu 28 DAS Start New Session Manual Vehicle Entry Vehicle Data Recorder Figure 5 21 e Click on the vehicle file you desired to enter the diagnostic menu directly 4 Vehicle Data Record 1 KACH 2 Ford2 Figure 5 22 5 3 Diagnostic Operation This function allows you to read and clear diagnostic trouble codes DTCs from a vehicle A Read Codes The Read Codes procedure varies for each vehicle being tested This section includes the following Read Codes procedures In the Function Menu screen Figure 5 23 select Read Codes This will display the Read Codes menu screen Figure 5 24 29 1 REET Meveye 5 2 Erase Codes Figure 5 23 Read Codes 1 2 KOER On Demand Self test 3 Retrieve CMDTCs Continuoug Memory Diagnostic Trouble Codes Figure 5 24 In the Read Codes menu select one of the options to proceed The screen will show as below Select options 1 ypyres 2 Freeze Frame MODE2 3 Pending Figure 5 25 Select one of the DTC options to view detailed diagnostic trouble code information P0046 Battery voltage high Status 60 No additional fault symptom available for this DTC P0098 Intake air temperature sensor 2 Circuit Tia Figure 5 26 You can save the code results for later review by selecting Save option on the bottom When you finished viewing the DTCs press the ESC button to return to previous screen B
28. Figure 5 16 pressing OK button will turn to diagnostic operation For more details refer to 5 3 Diagnostic Operation To exit the Auto Scan option press ESC button The scan tool will display a message Are you sure to quit to ask for your confirmation Select Yes to quit and No to cancel command 2 Control Unit Control Unit function will list down all the systems that might be available on the vehicle for you to select to test Select a system to display the function menu and start testing 4 System Menu AAKOS PCM RCM TCM Figure 5 18 3 Vehicle Information 27 Vehicle Information function allows you to view vehicle specific information for Specifications System Type and other Identification Vehicle Specification Vehicle Mustang Engine Type Other Capacity 3 8L Transmission Manual Fuel Type Gasoline Emission Level Federal Emission VIN 1FAFP40462F100819 PrefSuf 2R3APB _ VersionID 4612 OK Figure 5 19 4 Save and retrieve files Please follow the instructions above to finish the Auto Scan process Figure 5 15 then press the Function button corresponding to Save and name the record on the Save Vehicle Record screen Save Vehicle Record LDLo gt k Input vehicle name Maximum length is 25 characters Finish Show Esc Figure 5 20 To enter the diagnostic functions through the vehicle record option in future please follow these steps e Select Vehicle
29. IDs to the ECU When the registration is completed the screen displays as below 156 ID Regist Front left ID Front right ID Done Rear right ID Done Rear left ID Done Figure 14 13 J ECU Information This function enables you to retrieve the ECU information 1 From the TPMS diagnostic function menu Figure 14 1 use the UP DOWN scroll button to select the ECU Information and press OK button 2 The tool will display the ECU information for your viewing and saving Ecu Information Ecu Part number 40720 EH10B Save Figure 14 14 Select Save option to save the information for later review or press the ESC button to return to the previous menu 157 15 Warranty and Service Limited One Year Warranty Autel warrants to its customers that this product will be free from all defects in materials and workmanship for a period of one 1 year from the date of the original purchase subject to the following terms and conditions 1 The sole responsibility of Autel under the Warranty is limited to either the repair or at the option of Autel replacement of the scan tool at no charge with Proof of Purchase The sales receipt may be used for this purpose 2 This warranty does not apply to damages caused by improper use accident flood lightning or if the product was altered or repaired by anyone other than the Manufacturer s Service Center 3 Autel shall not be liable for any
30. OBD II Diagnostic Trouble Codes consists of a five digit alphanumeric code The first character a letter identifies which control system sets the code The other four characters all numbers provide additional information on where the DTC originated and the operating conditions that caused it to set Here below is an example to illustrate the structure of the digits 2 DTC Example Identifying spe Systems P 0 2 0 2 B Body cific malfunction C Chassis ing section of P Powertrain the systems U Network Code Type Sub systems Generic SAE 1 Fuel and Air Metering PO P2 P34 P39 2 Fuel and Air Metering BO B3 3 Ignition System or Engine Misfire CO C3 4 Auxiliary Emission Controls ea 5 Vehicle Speed Control and Idle Manufacturer Specific Controls P1 P30 p33 6 Computer Output Circuits B1 B2 7 Transmission Controls C102 8 Transmission Controls U1 U2 2 3 Location of Data Link Connector DLC The DLC Data Link Connector or Diagnostic Link Connector is the standardized 16 cavity connector where diagnostic scan tools interface with the vehicle s on board computer The DLC is usually located 12 inches from the center of the instrument panel dash under or around the driver s side for most vehicles If Data Link Connector is not located under dashboard a label should be there telling location For some Asian and European vehicles the DLC is located behind the ashtray and the ashtray must be remov
31. ON Select All Clear All to select or unselect all items 123 4 Press the OK button to confirm your selection and retrieve the selected live sensor data Particulate filter Enable regeneration Regeneratio n enabled Request regeneration Regeneratio nin DDE requested Pause Save Figure 13 9 e Press the corresponding FUNCTION BUTTON Save to store the retrieved live data for later playback or printing e Press the corresponding FUNCTION BUTTON Stop Save to stop saving data and resume live sensor data retrieving Press the corresponding FUNCTION BUTTON Pause to suspend live sensor data retrieving e Press the corresponding FUNCTION BUTTON Continue to resume live sensor data retrieving Ifthe One Graphic option is highlighted when a specific item is selected the graphic information is available When the sensor data is shown in graph the tool offers two more options Two Graphic and Merge Graphic The first option can display two graphs on the same screen and the last option can merge the two graphs into one 5 Press the ESC button to return to the previous menu 13 2 4 Identification A This function enables you to retrieve the DPF related control unit information 1 From the function menu Figure 13 3 use the UP DOWN scroll 124 button to select Identification A and press the OK button 2 The tool will display the ECU information for your
32. PMS related diagnostic trouble codes DTCs from a selected ECU 1 From the TPMS diagnostic function menu Figure 14 1 use the UP DOWN scroll button to select the Read Codes and press OK button 2 The tool will display TPMS DTCs retrieved from the vehicle s ECU for your viewing Select Save to store data for future review or press Esc button to exit without saving Figure 14 2 Read Codes B2617 05 STARTER RELAY CIRC B260B 08 STEERING LOCK UNIT B2618 0B BCM Figure 14 2 e Erase Codes 150 This function enables you to erase TPMS related diagnostic trouble codes DTCs in a selected ECU 1 From the TPMS diagnostic function menu Figure 14 1 use the UP DOWN scroll button to select the Erase Codes and press OK button 2 The tool will display a warning message for your confirmation Select Yes to continue No to exit Erase Codes DTCs and Freeze Data will be lost Do you wish to continue No Yes Figure 14 3 3 Tf the erase command is sent successfully the screen will show as below Figure 14 4 Press any button to continue To make sure codes are erased clearly run Read Codes again Erase Codes Erase Codes command sent Perform Read Codes function to verify Press any Key to continue Figure 14 4 Live Data This function enables you to view TPMS related data readings from a selected ECU With the live data screen displayed you can view 151 the data
33. TC Information 1 3 B1343 Air Inlet Door Movement 1 MIL Reg YES 2 DTC Status Current B1341 Air Mix Door 2 Movement 1 MIL Req YES Figure 11 28 4 Select Save option to store the codes or press ESC button to exit without saving B Erase Codes This function allows user to erase the SRS DTCs in vehicle ECU F NOTE If you plan to take the vehicle to a Service Center for repair DO NOT erase the SRS DTCs from the vehicle s 101 1 2 3 4 computer If the codes are erased valuable information that might help the technician troubleshoot the problem will be erased From the diagnostic function menu Figure 11 26 use the UP DOWN scroll button to select Diagnostic Trouble Codes and press the OK button Use the UP DOWN scroll button to select Clear DTC Information and press the OK button Figure 11 27 A warning message will come up asking for your confirmation Information This ECU has Stored multiple DTCs which may belong to various Functional Systems Freeze Frame Failure Record Data Will be cleared if stored Do you really want to Clear DTC information Yes No Figure 11 29 Select Yes to continue or No to exit When the command is sent the tool will display a message as below Information Erase Codes command sent Perform Read Codes function to verify Back Figure 11 30 102 5 To make sure the codes are erased completely perform Read DTC Information func
34. TCs and view live data streams from the vehicle s TPMS related ECUs You can also save recordings of data readings and perform special TPMS programming and reset procedures E NOTE All software screens shown in this manual are examples actual test screens may vary for each vehicle being tested Observe the menu titles and onscreen instructions to make correct option selections E NOTE For some operations you may need to activate the TPMS sensors on the wheel We offer a TPMS series of products For more information please visit our website www autel com 14 1 Enter Vehicle Information 1 Turn the ignition off 2 Make sure the car is properly blocked 3 Connect the tool to vehicle and power on 4 Turn the ignition on 5 Select TPMS icon in the Main Screen Figure 3 1 and press OK button A series of vehicle identification screens appears for you to identify the vehicle Take Nissan as an example 6 Select Nissan on the screen This initiates communication with the vehicle s computer and displays the next screen TPMS diagnostic function menu Figure 14 1 F NOTE If there is a linking error a notice screen will show up Please refer to 3 8 Product Troubleshooting for more details 149 Function Menu 1 Ecu Information 2 Read Codes 3 Erase Codes 4 Live Data 5 Active Test 6 Special Function Figure 14 1 14 2 TPMS Diagnostics Read Codes This function enables you to read T
35. Table of Contents 1 SAFETY PRECAUTIONS AND WARNINGBS eS A 2 GENERAL INFORMATION cssccssssssssscssscssccssssscnessssscessccssescssssssssssessoes 2 2 1 ON BOARD DIAGNOSTICS OBD ID ooo ce ceeccceccesceeteceseceeeeeseeeeseesseeeeseees 2 2 2 DIAGNOSTIC TROUBLE CODES DT CS cccccccesscceessscceesseeeeesseeeesseeees 2 2 3 LOCATION OF DATA LINK CONNECTOR DLC c cccscccesseestseeseeeeseeeseees 3 2 4 OBD IT READINESS MONITORS cccscccesscesseeeseeeeseeesecessecesseeeseessseeeseees 2 5 OBD II MONITOR READINESS STATUS 2 6 OBD TL DEFINITIONS ine e R R oes RUSS os 3 USING THE SCAN TOOL Zr hna R AR RRRS 8 31 TOOLDESCRIPTION ieie eia enee AE EAA A OEA 8 32 SPECIFICATIONS io E O O O TR A 10 3 3 ACCESSORIES INCLUDED cccsscessecesscseeceseeceseceseesessceueceseeesaesesessaes 10 34 KEYBOARD monia aa o a e Ore an AE SAARES 10 3S POWER ea E his E A as 11 3 6 SYSTEM SETUP s 0255555 EA A E A RR E E ERA RRR 12 3 7 VEHICLE COVERAGE ic sci scasvedovaieteesies a rote atte REAT E Med ERE 16 3 8 PRODUCT TROUBLESHOOTING cccccccsccsssceeseeeeseeesseeeeceseeesseeesseeeeeenaes 16 4 PLAYBACK DATA oii secisescsssicececseseccedecednsssocsentecesacevessesecseascosenseasssedessacceseese 18 4t REVIEWING DATA neeesser siise E n E E R RE 18 4 2 DELETING DATA one iE EEE EA ET E Sees 19 4 3 PRINTING DATA sarok n r e E N 19 5 DIAGNOSTIGS iivcsscerscsscsdesdscndeatsedseccoaastceb
36. acity 3 8L Transmission Manual Fuel Type Gasoline Emission Level Federal Emission Is this correct Yes no Figure 5 7 VIN code automatic acquisition Some vehicles could identify the VIN code intelligently saving customer s time to input complex information Taking Renault as an example a Jaguar 1 00 Lancia 1 00 LandRover 1 00 gt ad ty MD MINI 4 00 Maserati 1 00 Maybach 1 00 eo 8 Ope 1 00 Peugeot 1 00 Renault 4 00 Figure 5 8 RENAULT 1 VIN acquisition Figure 5 9 22 VIN acquisition 1 VIN CODE automatic acquisition 2 VIN CODE manual acquisition 3 Vehicle type manual acquisition Figure 5 10 In this mode the scan tool will communicate with the vehicle and read off the VIN code automatically then it will ask for your confirmation if the VIN code is correct If the VIN code is incorrect it will turn to manual mode to input VIN code see VIN code manual acquisition VIN code manual acquisition For some vehicles both selecting the options manually and acquiring the VIN are available for you to enter the vehicle information Taking Benz as an example AUDI V1 00 Abarth V 1 00 Alfal V1 0 BENZ V 1 00 BMW V 1 00 Citroen V 1 00 DACIA lt gt As W Dacia v1 00 EU Ford V 1 00 Fiat V 1 00 Figure 5 11 In the Benz Cars menu choose the item 2 Select by entering VIN and you can enter the VIN code directly
37. adiness Monitors being set to Not Ready Since the three continuous monitors are constantly evaluating they will be reported as Ready all of the time If testing of a particular supported non continuous monitor has not been completed the monitor status will be reported as Not Complete or Not Ready In order for the OBD monitor system to become ready the vehicle should be driven under a variety of normal operating conditions These operating conditions may include a mix of highway driving and stop and go city type driving and at least one overnight off period For specific information on getting your vehicle s OBD monitor system ready please consult your vehicle owner s manual 2 6 OBD II Definitions Power train Control Module PCM OBD II terminology for the on board computer that controls engine and drive train Malfunction Indicator Light MIL Malfunction Indicator Light Service Engine Soon Check Engine is a term used for the light on the instrument panel It is to alert the driver and or the repair technician that there is a problem with one or more of vehicle s systems and may cause emissions to exceed federal standards If the MIL illuminates with a steady light it indicates that a problem has been detected and the vehicle should be serviced as soon as possible Under certain conditions the dashboard light will blink or flash This indicates a severe problem and flashing is intended to discourag
38. ange value of selected character 6 LEFT SCROLL BUTTON When look up DTC definitions moves to previous character and views additional information on previous screens if DTC definition covers more than one screen views previous screen or previous frames of recorded data It is also used to view previous trouble code when viewing DTCs 9 RIGHT SCROLL BUTTON When look up DTC definitions moves to next character and view additional information on next screens if DTC definition covers more than one screen views next screen or next frames of recorded data It is also used to view next trouble code when viewing DTCs OK BUTTON Confirms a selection or action from a menu 12 EXTERNAL DC POWER PORT Connects the 12 volt power adapter to power the tool when disconnected from the vehicle 13 USB CONNECTOR Connects the scan tool to the PC for printing 3 2 Specifications 1 2 3 4 5 6 Display TFT color display 320 x 240 dpi Operating Temperature 0 C to 60 C 32 F to 140 F Storage Temperature 20 C to 70 C 4 F to 158 F External Power 12 0 to 18 0 V power provided via vehicle battery or adapter Dimensions Length Width Height 212 mm 8 35 110 5 mm 4 35 37 5 mm 1 48 Weight 0 28kg without wire 0 484kg with wire 3 3 Accessories Included 1 User s Manual Instructions on tool operations 2 CD Includes user s manual update software etc 3 O
39. arking brake replacement 1 Brake cable replacement 2 Electric parking brake replacement Figure 10 4 2 Inthe EPB screen use the UP DOWN button to select Brake cable replacement The screen shows as below 76 4 Brake cable replacement 1 Put in fitting removal position 2 Cable tensioning 3 Electric parking brake calibration Figure 10 5 In the Brake cable replacement screen the tool can perform three functions A Put in fitting or removal position This function enables you to fit in or remove the brake cable safely and easily It will take a few seconds to execute this command Put in fitting removal position Activation in progress Figure 10 6 When the job is done successfully the tool will display a message to confirm 77 Put in fitting removal position Positioning done To replace or remove the brake cables refer to the mechanical schedule Removal replacement electric parking brake primary and secondary cables Press any key to continue Figure 10 7 If the job fails to finish the tool will display a message to remind user of a problem After you exit the diagnosis program please repair the problem immediately Put in fitting removal position Activation done a problem occurred during the operation Press any key to continue Figure 10 8 B Cable tensioning Once the brake cable is fit in you would use this function to adjust its tension It will tak
40. ase Failure Turn Key on with Engine off message appears Figure 6 8 37 Erase Failure Turn Key on with Engine Off Press any key to continue Figure 6 8 4 Press any button to return to Diagnostic Menu 6 3 Live Data In this function you can not only read the live data but also record data for later review Viewing Data The View Data function allows viewing of live or real time PID data of vehicle s computer module s 1 To view live data use the UP DOWN scroll button to select Live Data from Diagnostic Menu and press the OK button Figure 6 3 2 Wait a few seconds while the scan tool validates the PID MAP Figure 6 9 Reading PID 01 Please Wait Figure 6 9 38 A Viewing Complete List 1 To view complete set of data use UP DOWN scroll button to select Complete List from Live Data menu and press the OK button Figure 6 10 1 oanye K mii IC 2 Custom List Figure 6 10 2 View live PIDs on the screen Use the UP DOWN scroll button for more PIDs if additional information is available on more than one page Figure 6 11 4 Complete List Numbers of DTCs 0 Fuel system 1 status OL Fuel system 2 status Calculated load value 0 0 Engine coolant 40 temperature Pause Graphics Save Figure 6 11 e If the Graphics on the bottom appears when a PID is highlighted graphic information is available Select Graphics to view graph
41. ation ECM monitors driving style and selects a suitable time to employ regeneration Cars driven a lot at idling speed and low load will attempt to regenerate earlier than cars driven more with high loads and engine speeds In order for regeneration to take place a prolonged high exhaust temperature must be attained In the event of the car being driven in such a way that regeneration is not possible i e frequent short journeys a diagnostic trouble code will eventually be registered DPF light and Check Engine indicator come on A service regeneration can be requested in the workshop using the diagnostic tool Before carrying out a forced DPF regeneration using the tool check the following items The fuel light is not on No DPF relevant faults stored in system The vehicle has the correct spec engine oil The oil for diesel is not contaminated IMPORTANT Before diagnosing a problem vehicle and attempting to perform an emergency regeneration it is important to obtain a full diagnostic log and read out relevant measured value blocks E NOTE The DPF will not regenerate if the engine management light is on or there is a faulty EGR valve 118 E NOTE The ECU must be re adapted when replacing the DPF and when topping up the fuel additive Eolys E NOTE All software screens shown in this manual are examples and actual test screens may vary for each vehicle being tested Observe the menu titles and onscreen i
42. by the California Air Resources Board ARB and implemented in 1988 to monitor some of the emission control components on vehicles As technology evolved and the desire to improve the On Board Diagnostic system increased a new generation of On Board Diagnostic system was developed This second generation of On Board Diagnostic regulations is called OBD II The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions When a problem is detected the OBD II system turns on a warning lamp MIL on the vehicle instrument panel to alert the driver typically by the phrase of Check Engine or Service Engine Soon The system will also store important information about the detected malfunction so that a technician can accurately find and fix the problem Here below follow three pieces of such valuable information 1 Whether the Malfunction Indicator Light MIL is commanded on or off 2 Which if any Diagnostic Trouble Codes DTCs are stored 3 Readiness Monitor status 2 2 Diagnostic Trouble Codes DTCs OBD II Diagnostic Trouble Codes are codes that are stored by the on board computer diagnostic system in response to a problem found in the vehicle These codes identify a particular problem area and are intended to provide you with a guide as to where a fault might be occurring within a vehicle
43. cates sequence of this item e Ifyou want to deselect the item press Clear button e To select all the items on the screen press Select All button To clear all the selected items on the screen press Clear All button 3 Press the OK button to view selected PIDs on screen 41 V Custom List Numbers of DTCs Fuel system 1 status OL Pause Graphics BEME Figure 6 15 4 Use the ESC button to return to previous menu Recording Data The Record Data function allows recording vehicle modules Parameter Identification PID data to help diagnose intermittent vehicle problems You could save data files to the SD card and then use the Playback function to view the saved files E NOTE The length of time for each frame varies per vehicle Generally one frame of data is about 1 4 second or 4 frames per second 1 To record live data with the live data screen displaying select Save on the bottom The scan tool will start timing to record retrieved live data and PID graphs e If you record live data under text mode following screen shows 4 Complete List Numbers of DTCs 0 Fuel system 1 status OL Fuel system 2 status 2 Calculated load value 0 0 Engine coolant 40 temperature Pause Graphics Saving 94 Figure 6 16 42 e If you record live data under graph mode following screen shows Engine RPM 812 rpm Vehicle Speed Sensor 0 km h 812 1
44. cation Figure 10 14 When the job is done successfully the tool will display a message to confirm 80 4 Electric parking brake calibration Electric parking brake cable calibration done Figure 10 15 If the job fails to finish the tool will display a message to remind user of a problem After you exit the diagnosis program please repair the problem immediately Electric parking brake calibration Activation done a problem occurred during the operation Press any key to continue Figure 10 16 3 In the EPB screen use the UP DOWN button to select Electric parking brake replacement The screen shows as below 4Flectric parking brake replacement 1 Put in fitting removal position 2 Cable tensioning 3 Electric parking brake calibration Figure 10 17 81 In the Electric parking brake replacement screen the tool can also perform three functions which details could refer to the same functions described in the Brake cable replacement menu above Active Test During an active test the tool is used for outputting commands to the ECU in order to drive the actuators This test determines the integrity of the system or parts by monitoring the operation of the actuators or by reading the EPB ECU data To carry out an active test please follow these steps 1 Follow the instructions above to display the Diag menu screen Figure 10 3 Select Active Test and a list of possible tests appear T
45. creen Or click on the Select All checkbox on the right side of screen and all updatable items will be selected automatically Then click the Update Selected Items button on the right side of screen Check the updating process by observing the upper left progress bar Downloads and upper right progress bar Installs You may also find progress information in the Status column of updated items Anytime you could click the Pause button on the right side of screen to suspend all progresses and the state of those suspended items would change to STOPPED To resume updating process you may need to select those suspended items again and then click the Update Selected Items button The progress will resume from the break point When the downloading is completed the downloaded programs will be installed automatically The new version will replace the old version 62 8 3 Single Updating Find out the desired updating item and click the Install button in the same line With updating in progress the Install button changes to STOPPED Check the updating process by observing the upper left progress bar Downloads and upper right progress bar Installs You may also find progress information in the Status column of updated items Anytime you could click the Pause button in the line to suspend this progress and the state of this item would change to STOPPED To resume updating process click the Install button in the line aga
46. d live sensor data 4 Press the ESC button to return to the previous menu 12 5 Utility This function allows users to do steering angle sensor calibration clear records and clear counter The function options vary with the vehicles being tested 114 From the function menu Figure 12 2 use the UP DOWN scroll button to select Utility and press the OK button The scan tool displays function menu as below Utility 1 Steering Angle Adjust 2 Records Clear 3 Counter Clear Figure 12 11 A Steering Angle Adjust 1 From the Utility function menu Figure 12 11 use the UP DOWN scroll button to select Steering Angle Adjust and press the OK button 2 The tool will display a series of instructions Follow the onscreen instructions step by step until the operation is completely finished If the operation is finished successfully the scan tool will display a confirmation message Figure 10 12 Otherwise it will display a message to remind user of a problem After you exit the diagnosis program please repair the problem immediately gt before diagnosis Steering Angle Adjust is complete Check that the VGRS warning light is OFF Press Back to exit this function Figure 12 12 115 B Records Clear 1 From the Utility function menu Figure 12 11 use the UP DOWN scroll button to select Records Clear and press the OK button 2 The tool will display a list of records Input the car name Motor Ov
47. e UP DOWN scroll button to select Particle filter regeneration and press the OK button 2 The tool communicates with the vehicle and reads the fault codes memory Follow the on screen instructions to check the prerequisites before particle filter regeneration such as the fuel the time and driving style Motor Electronics Problems percewjed G Motor Electronics as lt Lack of pa response gt ma diesel particul An attempt is made to regenerate the It is recommen particle filter in the follow test steps regeneration p A regeneration procedure is requested in test module Press ok butt the DDE control unit for this purpose Attention The fuel tank must contain at least 10 litres of fuel for the following steps eo 4 Cancel Figure 13 22 3 If every prerequisite is met the tool will ask for your confirmation to proceed as below Select Request to begin a regeneration or End to end the service function and exit 134 Motor Electronics Do you wish to request regeneration now Selection 1 Request regeneration 2 End service function End Request Figure 13 23 4 A series of instruction screens appears for users to perform the particle filter regeneration step by step Follow the onscreen instructions and press the OK button Figure 13 24 Do this until the tool reads off the regeneration status as below Figure 13 25 Motor Electronics In the next i
48. e vehicle operation The vehicle onboard diagnostic system can not turn the MIL off until necessary repairs are completed or the condition no longer exists DTC Diagnostic Trouble Codes DTC that identify which section of the emission control system has malfunctioned Enabling Criteria Also termed Enabling Conditions They are the vehicle specific events or conditions that must occur within the engine before the various monitors will set or run Some monitors 6 require the vehicle to follow a prescribed drive cycle routine as part of the enabling criteria Drive cycles vary among vehicles and for each monitor in any particular vehicle OBD II Drive Cycle A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the ready condition The purpose of completing an OBD II drive cycle is to force the vehicle to run its onboard diagnostics Some form of a drive cycle needs to be performed after DTCs have been erased from the PCM s memory or after the battery has been disconnected Running through a vehicle s complete drive cycle will set the readiness monitors so that future faults can be detected Drive cycles vary depending on the vehicle and the monitor that needs to be reset For vehicle specific drive cycle consult the vehicle s Owner s Manual Freeze Frame Data When an emissions related fault occurs the OBD II system not onl
49. e ESC button to return to the previous menu 6 7 On Board Monitor Test The On Board Monitor Test is useful after servicing or after erasing a vehicle s control module memory The On Board Monitor Test for non CAN equipped vehicles retrieves and displays test results for emission related power train components and systems that are not continuously monitored The On Board Monitor Test for CAN equipped vehicles retrieves and displays test results for emission related power train components and systems that are and are not continuously monitored Test and components IDs are determined by the vehicle manufacturer 49 In this test there are typically a minimum value a maximum value and a current value for each monitor By comparing the current value with the minimum and maximum value the scan tool will determine if it is OK 1 2 3 4 5 Use the UP DOWN scroll button to select On Board Monitor Test from Diagnostic Menu and press the OK button Figure 6 3 Wait a few seconds while the scan tool validates the PID MAP The scan tool will prompt you to select the vehicle make Vehicle Manufacturer 1 28 BUICK BMW CADILLAC CHRYSLER FORD GM Figure 6 26 After you select the vehicle manufacturer the scan tool shows the On Board Monitors tests for specific monitoring systems From On Board Monitor Test menu use the UP DOWN scroll button to select a test to view and press the OK button Figure 6 27 O
50. e a few seconds to execute this command Cable tensioning Activation in progress Figure 10 9 78 When the job is done successfully the tool will display a message to confirm 4 Cable tensioning Cable tensioning done Now calibrate the Electric parking brake see Electric parking brake replacement menu Press any key to continue Figure 10 10 If the job fails to finish the tool will display a message to remind user of a problem After you exit the diagnosis program please repair the problem immediately Cable tensioning Activation done a problem occurred during the operation Press any key to continue Figure 10 11 C Electric parking brake calibration When both functions above have completed successfully you still need to calibrate the electric parking brake system This function is to check if the EPB is working correctly which should be performed after work has been completed on the EPB or vehicle braking system It will remove any air gap from the brake pads and check the EPB pressure 79 After you select this function the tool will automatically work in the following procedure 4 Electric parking brake calibration Activation in progress Figure 10 12 4 Electric parking brake calibration Please wait The tool should stop and restart the communication with the Electric parking brake ECU Figure 10 13 4 Electric parking brake calibration Restart communi
51. e manufacturer of your vehicle is not listed use the UP DOWN scroll button to select Other and press the OK button 6 2 Erasing Codes CAUTION Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle s on board computer but also Freeze Frame data and manufacturer specific enhanced data Further the I M Readiness Monitor Status for all vehicle monitors is reset to Not Ready or Not Complete status Do not erase the codes before the system has been checked completely by a technician E NOTE Erasing codes does not mean that trouble codes in ECU have been eliminated completely As long as there is fault with the vehicle the trouble codes keeps on presenting This function is performed with key on engine off KOEO Do not start the engine 1 Use the UP DOWN scroll buttons to select Erase Codes from Diagnostics Menu and press the OK button Figure 6 3 2 A warning message comes up asking for your confirmation Figure 6 6 36 4 Erase trouble codes Are you sure Figure 6 6 e Ifyou do not want to proceed with erasing codes press ESC button or select NO to exit and return to previous screen 3 Press the OK button to confirm e If the codes are cleared successfully an Erase Done confirmation message shows on the display Figure 6 7 4 Erase Done Press any key to continue Figure 6 7 e If the codes are not cleared then an Er
52. e vehicle specifications select one of the three entries in the option screen PCM Part Number Calibration Number or Tear Tag to fill up the vehicle information Select An Option 1 PCM Part Number 2 Calibration Number 3 Tear Tag Figure 11 6 4 Taking the PCM Part Number entry for example you will need to fill up the accurate vehicle information in the input entry 89 PCM Part Number _ AL5A 12A650 AKA Figure 11 7 The three keys at the bottom of the screen work as below Finish After entering a new value use this key to save the value to the tool Edit Press this key to pop up a soft keyboard to facilitate your input Figure 11 8 Esc Press this key to exit 415Al G W EE IR T y GLY O ER E Ss ES ASODOFGHJKuL 4 s 6 Z ta Gd ME B INE M a 1 qwert SPACE Pre Backspace Figure 11 8 The three keys at the bottom of the screen work as below Finish When you finished the input select this key to confirm your input and exit Pre Moves a space to the left Backspace Uses this key to erase the previous digit or character when typing 90 E4 NOTE The data you input must be in the reasonable range If the input data is out of range the tool will display a warning message Input over flow 5 A screen message with the vehicle information will come up asking for your confirmation If the information is correct select Yes to continue otherwise
53. ed CD Make sure that your computer is connected to the Internet Load the SD card of the scan tool to your PC Run the Autel Update option in Autel PC Suit software Wait for the Log In window to pop up Figure 8 1 Update 6 21 Account John auteltech net Password lbs Forget Password Register Remember Password Figure 8 1 Enter your Autel ID and password and wait for the Update window to display If you forget your password unintentionally you may always click the Forget Password to link to our website and find your password back Select the product type and serial number click OK to continue In the Update window select the items you want to install Usually you should install all available updates 61 i Update VE 2i 03 G NAMOT 0125990009 WFE Installed Programs Select the updates to install from the list below Program Software Kit Version Status Size MB O Bmw EPB vi Install 70 24 Help CITROEN EPB vo i Install 4277 Hel JAGUAR EPB v3 x Install 0 00 Help LANDROVE EPB via x Install 0 00 Help OPEL EPB vo x Instali 26 99 Help PEUGEOT EPB nn E install 0 00 Help RENAULT EPB vi x Install 26 72 Hel EPB vi20 Install 0 00 Heip Figure 8 2 Generally there are two ways to update programs Batch Updating Select the programs that you would update by clicking on the check boxes next to those items Then click the Update Selected Items button on the right side of s
54. ed after the maintenance work has been completed F NOTE Autel accepts no responsibility for any accident or injury arising from the maintenance of the Electric Parking Brake system 10 2 EPB Maintenance 1 Turn the ignition off 74 2 Release the park brake and make sure the car is properly blocked 3 Connect the tool to vehicle and power on 4 Turn the ignition on 5 Select EPB icon in the Main Screen Figure 3 1 and wait for the vehicle manufacturer screen Choose the correct vehicle make Take PEUGEOT as an example a A AUDI BENZ BMW Citroen Jaguar LandRover H vV Opel Peugrot Renault Figure 10 1 6 After you have selected the vehicle make the electric parking brake system screen will display as below system o 1 EPB 2 ABS Figure 10 2 7 In the electric parking brake system screen use the UP DOWN button to select EPB to enter EPB system In the EPB diagnostic function the tool can read codes erase codes record live data read ECU information perform active test and 75 perform special function For the functions already being described see OBDII Diagnostics for details 1 Read Codes 2 Erase Codes 3 Live Data 4 5 Active Test ECU Information 6 Special Function Figure 10 3 Special Function 1 In the Diagnostic Menu Figure 10 3 use the UP DOWN button to select Special Function to do the EPB test which includes Brake cable replacement and Electric p
55. ed to access the connector If the DLC cannot be found refer to the vehicle s service manual for the location Ge 2 4 OBD II Readiness Monitors An important part of a vehicle s OBD II system is the Readiness Monitors which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system They are running periodic tests on specific systems and components to ensure that they are performing within allowable limits Currently there are eleven OBD II Readiness Monitors or I M Monitors defined by the U S Environmental Protection Agency EPA Not all monitors are supported by all vehicles and the exact number of monitors in any vehicle depends on the motor vehicle manufacturer s emissions control strategy Continuous Monitors Some of the vehicle components or systems are continuously tested by the vehicle s OBD II system while others are tested only under specific vehicle operating conditions The continuously monitored components listed below are always ready 1 Misfire 2 Fuel System 3 Comprehensive Components CCM Once the vehicle is running the OBD II system is continuously checking the above components monitoring key engine sensors watching for engine misfire and monitoring fuel demands Non Continuous Monitors Unlike the continuous monitors many emissions and engine system components require the vehicle to be operated under specific conditions before the monitor
56. electing Auto Scan will lead to retrieve the trouble codes in each system of the vehicle one by one It will take a few minutes to display Use the UP DOWN scroll button to select Auto Scan from Select an Option menu Figure 5 15 and press the OK button 25 100 Auto Scan PCM Powertrain Fault 1 Control Module Quick Erase Save Display DTC Figure 5 16 User is allowed to check the details of each system quickly erase DTC save the data and display DTC from the Auto Scan menu screen To select the options on the bottom simply press the corresponding function button Save You can save the Auto Scan information as Vehicle Record so that you will not need to follow the vehicle selection process again on the same vehicle in later tests For detailed instructions please refer to 4 Save and retrieve files Quick Erase By selecting this option the scan tool will erase all displaying DTCs and once again read the data and check the latest status of the system If the system did not repair the trouble codes will keep on displaying Display DTC This option allows you to read DTC definitions in the highlighted system If more than one fault is detected in a system the scan tool will display an option list for you to view different kind of DTCs or freeze frames 26 Select Option 1 CMDTCs Continuous memory diagnostic trouble codes 2 Freeze Frame Mode 2 3 pending Figure 5 17 In Auto Scan screen
57. erheat Record Not Table Data Motor Overheat Record Not Table Motor Overheat Record Not Table Clr History Figure 12 13 3 Select Clr Histroy to continue operation or ESC to exit When the command is sent the tool will display a message as below Input the car name Records Clear Completed Figure 12 14 C Counter Clear 1 From the Utility function menu Figure 12 11 use the UP DOWN scroll button to select Counter Clear and press the OK button 116 2 The tool will display a prerequisite message as below Select Yes to continue or No to exit Save Confirm DTC C1 555 exist Complete to repair the detected trouble on C1 555 The cause of the Trouble was not ECU malfunction Press Yes or No Yes No Figure 12 15 3 When the command is sent the tool will display a message as below Save Counter Clear Completed Plese confirm that DTC C1555 disappears if DTC C1555 exist check the detected trouble again Back Figure 12 16 117 13 DPF Service 13 1 DPF Safety The DPF function allows you to carry out numerous functions on the Diesel Particulate Filter system without having to send the car to a main dealer The tool will retrieve erase DPF related codes reset the DPF light after the filter has been replaced micromanage the injection rate and burn off collected particles when a maximum fill level is reached by performing a static dynamic regener
58. ess the OK button 2 From Unit of Measure screen use the LEFT RIGHT scroll button to select the desired unit of measurement Figure 3 4 EN METRIC Unit of Measure ke F English Metric Figure 3 4 3 Press the OK button to save your selection and return to previous menu Or press the ESC button to exit without saving Beep Set e The default setting is Beep On 1 From System Setup screen use the UP DOWN scroll button and LEFT RIGHT scroll button to select Beep and press the OK button 2 From Beep Set menu use the LEFT RIGHT scroll button to select ON or OFF to turn on off the beep Figure 3 5 Language Beep Set ee dx On Off Figure 3 5 3 Press the OK button to save your selection and return to previous menu Or press the ESC button to exit without saving 14 Key Test The Key Test function checks if the keyboard is working properly 1 From System Setup screen use the UP DOWN scroll button and LEFT RIGHT scroll button to select Key Test and press the OK button 2 Press any key to start test When you press a key the edge around corresponding key on the screen should turn to red Otherwise the key is not functioning properly 3 Double press ESC to return to previous menu LCD Test The LCD Test function checks if the LCD display is working normally 1 From System Setup screen use the UP DOWN scroll button and LEFT RIGHT scroll button to select LCD Test and
59. esssssesndessdessecincccesesdosesctedeenseddensceses 20 5 1 ENTERING VEHICLE INFORMATION cccccsccessessesscessceseesecsseesecesseseeeseenees 20 52 gt DIAGNOSTIC TEST 55 23 35 eae e r Aaen nere S ADAIR EIE EONIA EIN ENEE SCENAS 25 5 3 DIAGNOSTIC OPERATION ccccccesscessceesscessecesecesseceseeceseeseeeeseeesaeenseeeanes 29 6 GENERIC OBDII DIAGNOSTICS sseeseseosoeseseososseseseosoesescosossescosossesesecsossse 32 6 13 READ CO DI D DE A ES T ETE TT 34 6 2 ERASING CODES v erin erreser Aeae aA E E EA IRE E NAN ASEAS 36 6 3 TIVE DATA enas neea a E E OEE R RRR R 38 634 FREEZE FRAM E enre e O Od A ea ee OE ATEO EET AEE 44 6 5 RETRIEVING I M READINESS STATUS cc cccscccessceseeeseceseeeeseeesseeseeeaaes 45 6 652 O2 MONITOR TEST 6 5 53 eesee sos henge bevecees Seven dehebtens cass vetoes r 48 6 7 ON BOARD MONITOR TEST c cccssscessesssceeeceeseeeseceseceseeesseeesseeeeeenaes 49 6 8 COMPONENT PEST na e rE A ETE dart A 52 10 11 12 13 14 15 6 9 VIEWING VEHICLE INFORMATION ccc cccessceseceesecesseeeseeeseeeeseeesseeeeeenaes 6 10 MODULES PRESENT ccccsccssscsssseeseccesecessecnseecsseceseecnseesseecsseeesseesseessaes 6 11 DT COOK UP 32 oie cece eae epi ose Aa ete A A ES PRINT DATA uuu cccsecscscecescsccecscsescscsccssscncesesssssssencecssscssssssesseesscssssssessoess SORT WARE UPRDA TE sis iscsicissiestesesccssnsenissveissveseusncdscesonsssseesteisessi
60. ested If there is a linking error please refer to product troubleshooting finish this procedure please follow these steps Taking PEUGEOT as an example 1 2 From the vehicle make screen select PEUGEOT and press OK button 2 HoH Figure 9 5 Step by step select the right options for your vehicle according to each screen that appears PEUGEOT 1 206 206MUX 2 206 3 207 5 308 6 406 Figure 9 6 68 3 After you have entered the vehicle information the oil reset screen will display as below 4 1 Instrument panel 2 BSI Figure 9 7 4 The Instrument Panel option enables you to finish oil reset service in one step by resetting the ECU to default values automatically The procedures work as below e In the Oil Reset menu select Service Zero Reset function and press OK button Oil Reset 1 Service Zero Reset Figure 9 8 e The tool will automatically begin resetting the vehicle ECU to default values 69 4 Service Zero Reset Check the resetting of the maintenance to zero Cancel Figure 9 9 e When the resetting is finished the tool will display a confirmation message Service Zero Reset Operation Completed Press any key to continue Figure 9 10 5 The BSI option enables you to finish oil reset service automatically and manually The procedures work as below e Jn the Oil Reset menu select Resetting to zero of the service mileage
61. fferent criteria and methods for stopping the test once it has been started Before starting the Component Test refer to the vehicle service manual for instructions to stop the test 1 Use the UP DOWN scroll button to select Component Test from Diagnostic Menu and press the OK button Figure 6 3 2 Wait for the scan tool to display the Component Test menu Component Test 1 EVAP Sys Leak Test Figure 6 32 52 3 If the test has been initiated by the vehicle a confirmation message will be displayed on the screen Component Test Command Sent Press any key to continue Figure 6 33 Some vehicles do not allow scan tools to control vehicle systems or components If the vehicle under test does not support the EVAP Leak Test an advisory message is displayed on the screen Component Test The selected mode is not supported Press any key to continue Figure 6 34 4 Press any key to return to previous screen 6 9 Viewing Vehicle Information The Vehicle Info function enables retrieval of Vehicle Identification No VIN Calibration ID Nos CINs Calibration Verification Nos CVNs and In use Performance Tracking on 2000 and newer vehicles that support Mode 9 1 Use UP DOWN scroll button to select Vehicle Info from the Diagnostic Menu and press OK button Figure 6 3 53 2 An advisory message comes up to remind you Wait a few seconds or press any key to continue Vehicle Info Turn key
62. function and press OK button 4 Oil Reset 1 Resetting to zero of the service faaliketelers 2 Maintenance Figure 9 11 70 The tool will reset the oil service to zero automatically Resetting to zero Maintenance mileage zero reset carried out Press any key to continue Figure 9 12 In the Oil Reset menu Figure 9 11 select Maintenance function and press OK button The screen will display the preset maintenance information of the vehicle The information items vary with different vehicles 4 Period before service 6 months First maintenance china threshold Maintenance 7400 limit km Finish Figure 9 13 For the First maintenance threshold you have two choices Select the correct option and press OK button to save the change 2 Another country Figure 9 14 71 Ei Vv For the Period before service or Maintenance limit press Edit key on the bottom to pop up a soft keyboard to facilitate your input Period before service months Finish Pre F Ted of Tes Figure 9 15 The three keyboard function keys work as below Finish When you finished the input select this key to confirm your input and exit Pre Moves a space to the left Backspace Uses this key to erase the previous digit or character when typing NOTE The data you input must be in the reasonable range which is defined by the preset values in ECU If you enter a data out of
63. g stroke i Figure 13 12 3 The tool will display a function list menu as below In this menu you can enter new value for adjustment or reset adjustment to 0 Motor Electronics Set value start volume Adjustment 1541 0 Nm Selection 1 Enter new value for adjustment 2 Reset adjustment to 0 Figure 13 13 126 The option keys at the bottom of the screen work as below 1 Enter new value for adjustment 2 Reset adjustment to 0 3 End with programming the new value is permanently stored 4 End without programming the old value is retained A Enter new value for adjustment From the Starting Basic Inspection Quantity menu Figure 13 13 use the LEFT RIGHT scroll button to select 1 and press the OK button The screen displays as below You will need to input a new value for fuel delivery rate adjustment Motor Electronics Enter new value for starting fuel delivery rate adjustment 0 7 Finish Show Esc Figure 13 14 The three keys at the bottom of the screen work as below Finish After entering a new value use this key to save the value to the tool Show Press this key to pop up a soft keyboard to facilitate your input Figure 13 15 Esc Press this key to exit 127 Motor Electronics Finish Pre Backspace Figure 13 15 The three keys at the bottom of the screen work as below Finish When you finished the input select this key to confirm your
64. gines MIS Misfire Monitor 46 FUEL Fuel System Monitor CCM Comprehensive Component Monitor EGR EGR System Monitor HCCAT NMHC Catalyst Monitor NCAT NOx Aftertreatment Monitor BP Boost Pressure System Monitor EGS Exhaust Gas Sensor Monitor e PM PM Filter Monitor 4 Since DTCs cleared MIL Status OFF Misfire Monitoring N A Fuel system monitoring OK Comprehensive OK component monitoring Catalyst monitoring N A Heated catalyst monitor N A Figure 6 21 5 If the vehicle supports readiness test of This Drive Cycle a screen of the following displays Figure 6 22 4 This Drive Cycle MIL Status OFF Misfire Monitoring N A Fuel system monitoring OK Comprehensive OK component monitoring Catalyst monitoring N A Heated catalyst monitor N A Figure 6 22 6 Use the UP DOWN scroll button for more PIDs if additional information is available on more than one page Or use the LEFT RIGHT scroll button to view PIDs in the previous next page 47 7 Press the ESC button to return to Diagnostic Menu 6 6 O2 Monitor Test OBD2 regulations set by SAE require that relevant vehicles monitor and tests on the oxygen O2 sensors to identify problems related to fuel efficiency and vehicle emissions These tests are not on demand tests and they are done automatically when engine operating conditions a
65. gure 13 2 13 2 DPF Diagnostics Use the UP DOWN scroll button to select Control Units in the menu Figure 13 2 The computer will automatically detect the DPF related system DDE which is dedicated for BMW For other vehicles the system may be different Then the screen displays as below 120 Function Menu 1 Identification A 2 Read Codes 3 Erase Codes 4 Live Data Figure 13 3 13 2 1 Read Codes This function allows user to read the DPF DTCs from vehicle ECU 1 From the function menu Figure 13 3 use the UP DOWN scroll button to select Read Codes and press the OK button 2 View DTCs and their definitions on screen Fault Codes DDE Particulate filter system Figure 13 4 3 Select Save option to store the codes or press ESC button to exit without saving 13 2 2 Erase Codes This function allows user to erase the DPF DTCs in vehicle ECU 1 From the function menu Figure 13 3 use the UP DOWN scroll button to select Erase Codes and press the OK button 121 2 A warning message will come up asking for your confirmation DTCs and Freeze Data will be lost Do you wish to continue Figure 13 5 3 Select Yes to continue or No to exit When the command is sent the tool will display a message as below Erase Codes command sent Perform Read Codes function to verify Press any key to continue Figure 13 6 4 To make sure the codes are erased completely perform Read
66. he scan tool and wait for the Main Screen to appear 65 3 Select Oil Reset icon in the Main Screen Figure 3 1 and wait for the vehicle manufacturer screen Choose the correct vehicle make There are two ways to perform the reset service A Manual Reset Almost all Asian vehicles and most American and European vehicles can be reset manually by technicians E NOTE In this manner the scan tool will not communicate with the vehicle being tested To finish this procedure please follow these steps Taking Ford as an example 1 From the vehicle make screen select Ford and press OK button a ft Jeep Lincoln Mercury Oldsmobile Figure 9 1 2 Step by step select the right options for your vehicle according to each screen that appears 66 4 1 Explorer 2 Freestyle 3 Windstar Figure 9 2 1 2005 2 2003 2004 3 1998 2002 Figure 9 3 3 After entering the vehicle information the scan tool displays manual reset message as below 4 Manual Reset 1 Select Press Reset At Oil Change from the setup control for the current display mode 2 Press Reset Control to reset Oil change Figure 9 4 4 Follow the instructions to reset the service manually 5 Press ESC button to exit 67 B Auto Reset Most American and European vehicles can be reset automatically by the scan tool Ei To NOTE In this manner the scan tool will communicate with the vehicle being t
67. he test items in the list vary with different vehicles Active 1 Apply electric parking brake 2 Release electric parking brake Figure 10 18 Select a test and the tool will display an information screen as The apply electric parking brake operation is used to test the operation of the brake cables statically If you start the actuator test you must wait for the component to stop operating before starting another actuator test Press OK to apply the electric parking brake or press Cancel to go back to the list of possible operation Select OK to continue or Cancel to exit 82 4 The tool may display information during and after the test The information varies by vehicle 4 Apply electric parking brake Listen to the noise of the Electric motor Figure 10 19 5 When the test is finished there may be three results displaying on the screen e The test is finished successfully e The test is stopped by the user e The test did not finish In the first condition the tool will display an information screen as The operation was performed correctly Put the vehicle on a vehicle lift and check that the rear wheels are locked Check that the Electric parking brake on message is display on the control panel and that the LED illuminates on the control panel In the second condition the tool will display an information screen as Operation of the actuator test was stopped by the user Press
68. hicle s DLC Turn the ignition on but do not start the engine Turn on the scan tool and wait for the Main Screen to appear Use the UP DOWN scroll button or LEFT RIGHT scroll button to select SAS in the Main Screen Figure 3 1 Wait for a series of vehicle identification screens appears for user to identify the vehicle Figure 13 1 On each screen that appears use the UP DOWN scroll button to select the correct option and then press the OK button Do this until the vehicle is completely identified 108 Select Menu 4 Select Menu 4 System Menu Figure 12 1 K Use the UP DOWN scroll button to select VGRS in the menu The screen displays as below 1_ Read Codes 2 Erase Codes 3 Freeze Frame Data 5 Utility Figure 12 2 12 1 Read Codes This function allows user to read the SAS DTCs from vehicle ECU 1 From the function menu Figure 12 2 use the UP DOWN scroll button to select Read Codes and press the OK button 109 2 View DTCs and their definitions on screen Read Codes 6 C1515 Actuator Neutral Position Calibration Undone C1516 Actuator Neutral Position Calibration Incomplete C1532 Figure 12 3 3 Select Save option to store the codes or press ESC button to exit without saving 12 2 Erase Codes This function allows user to erase the SAS DTCs in vehicle ECU 1 From the function menu Figu
69. iagnostics Take GM as an example 3 6 L LFX 1 Supplemental Inflatable Restraint 2 Electronic Brake Control Module Figure 11 12 From the ABS and SRS menu use the UP DOWN scroll button to select Electronic Brake Control Module and press the OK button The screen displays as below Electronic e Control Module 1 Diagnostic Trouble Codes DTC 2 Data Display 3 Special Functions 4 Module ID Information Figure 11 13 Read Codes This function allows user to read the ABS DTCs from vehicle ECU 1 From the diagnostic function menu Figure 11 13 use the UP DOWN scroll button to select Diagnostic Trouble Codes and press the OK button 93 Diagnostic Trouble Codes DTC 1 Read DTC Information 2 Clear DTC Information Figure 11 14 2 Use the UP DOWN scroll button to select Read DTC Information and press the OK button Figure 11 14 3 View DTCs and their definitions on screen DTC Info 2 C0151 Right Hand TCS Solenoid 1 Circuit C0051 Right Rear Wheel Speed Circuit Range Performance Figure 11 15 4 Select Save option to store the codes or press ESC button to exit without saving Erase Codes This function allows user to erase the ABS DTCs in vehicle ECU F NOTE If you plan to take the vehicle to a Service Center for repair DO NOT erase the ABS DTCs from the vehicle s computer If the codes are erased valuable information that might help the
70. ial _185 deg 2781 3 927 1 Pause Merge Graph Save Figure 12 9 Press the corresponding FUNCTION BUTTON Text or the ESC button to return to previous screen B Custom List This feature lets you customize the scan tool display to show only those PIDs that are of interest at the current time You can customize the Live Data display by placing the Scan Tool in Custom List mode and selecting only the PIDs that you wish to display To customize the Live Data display proceed as follows 113 1 To retrieve customized live sensor data use the UP DOWN scroll button to select Custom List from Live Data menu Figure 12 7 and press the OK button 2 Use the UP DOWN scroll button to move to the desired item and press the corresponding FUNCTION BUTTON Select to choose Live Data Steering Pos 1 Parallel Steering Pos 2 Serial Steering Sensor1 Steering Sensor2 Steering Sensor3 Vehicle Speed Vsc ECU Wheel Speed Right Select All Clear Clear All Figure 12 10 The Selected items are marked with ticks on the left The number on the right indicates sequence of the selected item Press the corresponding FUNCTION BUTTON Clear to unselect items or press the corresponding FUNCTION BUTTON Select All Clear All to select or unselect all items 3 Press the OK button to confirm your selection and retrieve the selecte
71. in The progress will resume from the break point When the downloading is completed the downloaded program will be installed automatically The new version will replace the old version View or Delete Programs To view the list of installed programs or to delete an installed program please follow these steps Click on the Installed Programs tag entry and the page will show the list of programs installed Select the program s that you would delete lt Batch delete Select the programs that you would delete by clicking on the check boxes to the left of those items Then click the Delete button on the right side of screen Single delete Click the Uninstall button in the line of your would be deleted program A window asking Are you sure to delete the software will pop up for your confirmation 63 Figure 8 3 e Click on Yes to delete the program s selected or on No to cancel the action e The deleted program will automatically add to the end of program list in the Update page in case you would like to install again Theoretically all programs in latest versions will be automatically compatible with the older versions but if your scan tool do have a compatible problem and want to retrieve the older version for some programs you may need to delete them first then install the older version again Choose older version from the pull down menu of program version Eves erra ota aloes ane aaro
72. in Text or graphical format record and save files for later viewing sort the data pause the readings and view past data and more From the TPMS diagnostic function menu Figure 14 1 use the UP DOWN scroll button to select the Live Data and press OK button Live Data 1 All Data 2 Custom List Figure 14 5 All Data 1 From the Live Data menu Figure 14 5 use the UP DOWN scroll button to select All Data and press the OK button 2 The tool will display a list of all live sensor data Figure 6 6 Live Data VEHICLE SPEED AIR PRESS FL 15 psi AIR PRESS FR 1 7 psi AIR PRESS RR 2 0 psi AIR PRESS RL 2 2 psi Pause One Graphic Save Figure 14 6 Press the corresponding FUNCTION BUTTON Save to store the retrieved live data for later playback or printing 152 Press the corresponding FUNCTION BUTTON Stop Save to stop saving data and resume live sensor data retrieving Press the corresponding FUNCTION BUTTON Pause to suspend live sensor data retrieving Press the corresponding FUNCTION BUTTON Continue to resume live sensor data retrieving If the One Graphic option is highlighted when a specific item is selected the graphic information is available When the sensor data is shown in graph the tool offers two more options Two Graphic and Merge Graphic The first option can display two graphs on the same screen Figure 14 7 and the last option ca
73. input and exit Pre Moves a space to the left Backspace Uses this key to erase the previous digit or character when typing E4 NOTE The data you input must be in the reasonable range If the input data is out of range the tool will display a warning message Permissible adjustment range exceeded B Reset adjustment to 0 From the Starting Basic Inspection Quantity menu Figure 13 13 use the LEFT RIGHT scroll button to select 2 and press the OK button The tool will automatically reset the value to zero C Store data and exit When you have finished the fuel delivery rate adjustment use the LEFT RIGHT scroll button to select 3 and press the OK button to store the new value in the control units or select 4 and press the OK button to retain the old value 13 3 2 Injection Rate 128 This function enables you to adjust the injection volume 1 From the service functions menu Figure 13 11 use the UP DOWN scroll button to select Injection rate and press the OK button 2 The tool communicates with the vehicle and reads the fault codes memory Follow the on screen instructions to finish this procedure 3 Then the tool will display as below In this function you can enter new value for matching or reset matching to 100 Motor Electronics Set value injection volume matching 100 Selection 1 Enter new value for adjustment 2 Reset adjustment to 100 Figure 13 16 The option key
74. is ready These 4 monitors are termed non continuous monitors For different ignition type engines the available monitors are different too The following monitors are to be used for spark ignition engines only 1 EGR System 2 O2 Sensors 3 Catalyst 4 Evaporative System 5 02 Sensor Heater 6 Secondary Air 7 Heated Catalyst The following monitors are to be used for diesel engines only 1 EGR System 2 NMHC Catalyst 3 NOx Aftertreatment 4 Boost Pressure System 5 Exhaust Gas Sensor 6 PM Filter 2 5 OBD II Monitor Readiness Status OBD II systems must indicate whether or not the vehicle s PCM s monitor system has completed testing on each component Components that have been tested will be reported as Ready or Complete meaning they have been tested by the OBD II system The purpose of recording readiness status is to allow inspectors to determine if the vehicle s OBD II system has tested all the components and or systems The power train control module PCM sets a monitor to Ready or Complete after an appropriate drive cycle has been performed The drive cycle that enables a monitor and sets readiness codes to Ready varies for each individual monitor Once a monitor is set as Ready 5 or Complete it will remain in this state A number of factors including erasing of diagnostic trouble codes DTCs with a scan tool or a disconnected battery can result in Re
75. itors OK 2 Monitors INC 0 Figure 6 1 e If more than one module is detected you will be prompted to select a module before testing Figure 6 2 y Control Module 2 Module A4 Figure 6 2 e Use the UP DOWN scroll button to select a module and press the OK button 33 6 1 Read Codes 1 Reading Codes can be done with the key on engine off KOEO or with the key on engine running KOER Stored Codes are also known as hard codes which are fault codes or trouble codes that have been stored in the vehicle computer memory because the faults have reoccurred for more than a specified amount of key cycles These codes will cause the control module to illuminate the malfunction indicator light MIL when emission related fault occurs Pending Codes are also referred to as maturing codes or continuous monitor codes They indicate problems that the control module has detected during the current or last driving cycle but are not considered serious yet Pending Codes will not turn on the malfunction indicator lamp MIL If the fault does not occur within a certain number of warm up cycles the code clears from memory Permanent Codes are DTCs that are confirmed and are retained in the non volatile memory of the computer until the appropriate monitor for each DTC has determined that the malfunction is no longer present and is not commanding the MIL on Permanent DTC shall be st
76. ll button to select one option and press the OK button The screen displays as below You will need to input a new value for Cylinder injector Motor Electronics CAITEEC Adjustment values currently stored Cylinder 1 CAITEEC Cylinder 2 DANTWGD Cylinder 3 EASUEIE Cylinder 4 FAWUWLF Finish Show Esc Figure 13 20 132 The three keys at the bottom of the screen work as below Finish After entering a new value use this key to save the value to the tool Show Press this key to pop up a soft keyboard to facilitate your input Figure 13 21 Esc Press this key to exit Motor Electronics Figure 13 21 The three keys at the bottom of the screen work as below Finish When you finished the input select this key to confirm your input and exit Pre Moves a space to the left Backspace Uses this key to erase the previous digit or character when typing B Restore the old value From the Injector rate adjustment menu Figure 13 19 use the LEFT RIGHT scroll button to select Restore and press the OK button The tool will automatically retain the old value When you have finished the injector rate adjustment use the LEFT RIGHT scroll button to select Back and press the OK button to return to the previous menu 133 13 3 4 Particle Filter Regeneration This function enables you to perform the particle filter regeneration 1 From the service functions menu Figure 13 11 use th
77. n Se he rr Figure 8 4 64 9 Oil Reset 9 1 General Information The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use An oil change is required whenever indicated by the display and according to the recommended maintenance schedule Whenever the oil is changed reset the system so it can calculate when the next oil change is required If a situation occurs where the oil is changed prior to a service indicator being turned on also reset the system MPORTANT Always reset the engine oil life to 100 after every oil change E NOTE All required work must be carried out before the service indicators are reset Failure to do so may result in incorrect service values and cause DTCs to be stored by the relevant control module E NOTE For some vehicles the scan tool can perform added functionality to reset additional service lights maintenance cycle service interval Taking BMW as an example its service reset function includes engine oil spark plugs front rear brakes coolant particle filter brake fluid microfilter vehicle inspection exhaust emission inspection and vehicle check All software screens shown in this manual are examples actual test screens may vary for each vehicle being tested Observe the menu titles and onscreen instructions to make correct option selections 9 2 Reset Operation 1 Turn the ignition on but do not start the engine 2 Turn on t
78. n Board Monitor Test 1 Test 01 Data 2 Test 03 Data 3 Test 10 Data 4 Test 21 Data 5 Test 22 Data 6 Test 25 Data Figure 6 27 50 If the vehicle under test does not support the mode an advisory message will be displayed on the screen Figure 6 28 On Board Monitor Test The selected mode is not supported Press any key to continue Figure 6 28 For CAN equipped vehicles test selections can be as below 4 On Board Monitor Test 1 EGR Monitor 2 Mis Fire Monitor Data 3 Mis Fire Cylinder 1 Data 4 Mis Fire Cylinder 2 Data 5 Mis Fire Cylinder 3 Data 6 Mis Fire Cylinder 4 Data Figure 6 29 6 Use the UP DOWN scroll button to select the desired monitor from On Board Monitor Test menu and press the OK button 7 View test data on screen 4 Test 01 Data ID 11 Module 10 Test Value Min Limit Max Limit Status Figure 6 30 51 For CAN equipped vehicles test results displayed can be as below Flow Test Test Value 0 10 Min Limit 0 00 Max Limit 95 0 Status OK Figure 6 31 8 Press ESC button to return to the previous menus 6 8 Component Test The Component Test function allows initiating a leak test for the vehicle s EVAP system The scan tool itself does not perform the leak test but commands the vehicle s on board computer to start the test Different vehicle manufacturers might have di
79. n merge the two graphs into one Figure 14 8 AIR PRESS FL AIR PRESS FR Save Merge Graphic Pause Figure 14 7 AIR PRESS FL 8 60 Kpa AIR PRESS FR 10 32 Kpa 12 90 15 48 5 16 4 30 Save Text Pause Figure 14 8 153 e Press the corresponding FUNCTION BUTTON Text or the ESC button to return to previous screen Custom List This option lets you select and view TPMS related data readings for specific components sensors switches etc controlled by a specific ECU 1 To retrieve customized live sensor data use the UP DOWN scroll button to select Custom List from Live Data and press the OK button Figure 14 5 2 Use the UP DOWN scroll button to move to the desired item and press the corresponding FUNCTION BUTTON Select to choose Custom List AIR PRESS FL AIR PRESS FR AIR PRESS RR AIR PRESS RL ID REGST FL1 ID REGST FR1 ID REGST RR1 Clear All Select Select All Figure 14 9 The Selected items are marked with ticks on the left The number on the right indicates sequence of the selected item e Press the corresponding FUNCTION BUTTON Clear to unselect items or press the corresponding FUNCTION BUTTON Select All Clear All to select or unselect all items 3 Press the OK button to confirm your selection and retrieve the selected live sensor data 4 Press the ESC button to return to the previous menu 15
80. ning of the current drive cycle An I M Readiness Status result of NO does not necessarily indicate that the vehicle being tested will fail the state I M inspection For some states one or more such monitors may be allowed to be Not Ready to pass the emissions inspection OK Indicates that a particular monitor being checked has completed its diagnostic testing INC Indicates that a particular monitor being checked has not completed its diagnostic testing N A The monitor is not supported on that vehicle 45 1 Use the UP DOWN scroll button to select I M Readiness from Diagnostic Menu and press OK button Figure 6 3 2 Wait afew seconds while the scan tool validates the PID MAP 3 If the vehicle supports both types of tests then both types will be shown on the screen for selection Figure 6 20 4 I M Readiness 1 Since DTCs Cleared 2 This Drive Cycle Figure 6 20 4 Use the UP DOWN scroll button as necessary to view the status of the MIL light ON or OFF and the following monitors For spark ignition engines e MIS Misfire Monitor e FUEL Fuel System Monitor CCM Comprehensive Component Monitor EGR EGR System Monitor O2S O2 Sensors Monitor CAT Catalyst Monitor EVAP Evaporative System Monitor e HTR O2 Sensor Heater Monitor AIR Secondary Air Monitor HCAT Heated Catalyst Monitor For compression ignition en
81. nstructions to make correct option selections E NOTE If the vehicle needs to be driven in order to perform a DPF service ALWAYS have a second person help you One person should drive the vehicle while the other person observes the screen on the Tool Trying to drive and observe the Scan Tool at the same time is dangerous and could cause a serious traffic accident Take BMW as an example Follow the steps below to do the tests Turn the ignition off Locate the vehicle s 16 pin Data Link Connector DLC Plug the scan tool cable connector into the vehicle s DLC 1 2 3 4 Turn the ignition on and the engine may be off or running 5 Turn on the scan tool and wait for the Main Screen to appear 6 Use the UP DOWN scroll button or LEFT RIGHT scroll button to select DPF in the Main Screen Figure 3 1 7 Wait for a series of vehicle identification screens appears for user to identify the vehicle On each screen that appears use the UP DOWN scroll button to select the correct option and then press the OK button Do this until the vehicle is completely identified 119 Alfa V1 00 VEN 1 1 Series s e eros Citroen v1 00 m itroen 3 5 Series I Model series a 4 6 Series 1 E38 5 7 Seres 2 E65 E66 E68 Jaguar v1 00 5 x Series 7 Z Series 8 Z Series Figure 13 1 8 The screen displays as below Main Groups 1 Control Units 2 Service functions Fi
82. o return to the previous menu Special Functions This function allows users to do various active tests or module programming The function options vary with the vehicles being tested 97 1 From the diagnostic function menu Figure 11 13 use the UP DOWN scroll button to select Special Functions and press the OK button Special Functions 1 Automated Bleed 2 Pump Motor Test 3 Solenoid Tests Figure11 21 2 Use the UP DOWN scroll button to select the desired function and press the OK button Taking Automated Bleed as an example 3 A series of message screens appears to instruct users on the whole procedure Follow the on screen instructions step by step to take the proper operation Information Information Information Information Information Release Brake Pedal Open Left Front Bleeder Screw Continue Figurel 11 22 98 4 Take actions properly until the tool displays a completion message Information Close Right Rear Bleeder Screw The Procedure is complete A Figure 11 23 Module ID Information This function allows users to view the selected control module information 1 From the diagnostic function menu Figure 11 13 use the UP DOWN scroll button to select Module ID Information and press the OK button 2 View module information present with its IDs and part numbers Module ID Information End Model Part 20001331 Number
83. on as necessary until all the data have been shown up Figure 6 19 V Freeze Frame DTC that caused required P0193 freeze frame data storage Fuel system 1 status OL Fuel system 2 status ES Calculated load value 0 0 Engine coolant 40 Re temperature Figure 6 19 If there is no available freeze frame data an advisory message No freeze frame data stored shows on the display 44 4 Select Save to record freeze frame A confirming message Save success shows on the display and scan tool return to previous menu 5 If you don t want to save the freeze frame data press ESC button to return to previous screen 6 5 Retrieving I M Readiness Status I M Readiness function is used to check the operations of the Emission System on OBD2 compliant vehicles It is an excellent function to use prior to having a vehicle inspected for compliance to a state emissions program CAUTION By clearing trouble codes you also clear the readiness status for the individual emission system readiness tests In order to reset these monitors the vehicle must be driven through a complete drive cycle with no trouble codes in memory Times for reset vary depending on vehicle Some latest vehicle models may support two types of I M Readiness tests A Since DTCs Cleared indicates status of the monitors since the DTCs are erased B This Drive Cycle indicates status of monitors since the begin
84. on with engine off Press any key to continue Figure 6 35 3 Wait for the scan tool to display the Vehicle Info menu Vehicle Info 1 Vehicle ID Number 2 Caibration ID 3 Cal Verf Number Figure 6 36 Ifthe vehicle does not support this mode a message shows on the display warning that the mode is not supported 4 From Vehicle Info Menu use the UP DOWN scroll button to select an available item to view and press the OK button 5 View retrieved vehicle information on screen 54 4 Vehicle ID Number VIN 1FAFP40462F100819 Figure 6 37 6 Press the ESC button to return previous menu 6 10 Modules Present The Modules Present function allows viewing of the module IDs and communication protocols for OBD2 modules in the vehicle 1 Use the UP DOWN scroll button to select Modules Present from Diagnostic Menu and press OK button Figure 6 3 2 View modules present with their IDs and communication protocols 4 Modules Present Protocol ID SAE J1850 PWM 10 Figure 6 38 3 Select Save to save the modules data and return to previous menu Or press ESC button to exit 6 11 DTC Lookup 55 The DTC Lookup function allows user to search definitions of DTC stored in built in DTC library 1 Use the UP DOWN scroll button to select DTC Lookup from Diagnostic Menu and press OK button Figure 6 3 2 Wait for the scan tool to display the DTC Lookup screen
85. or to the column Any maintenance or repair work on the steering linkage steering gear or other related mechanism Wheel alignment or wheel track adjustment Accident repairs where damage to the steering angle sensor or assembly or any part of the steering system may have occurred NOTE AUTEL accepts no responsibility for any accident or injury arising from servicing the SAS system When interpreting DTCs retrieved from the vehicle always follow the manufacturer s recommendation for repair NOTE All software screens shown in this manual are examples actual test screens may vary for each vehicle being tested Observe the menu titles and onscreen instructions to make correct option selections NOTE Before starting procedure make sure vehicle has ESC Look for button on dash 107 Take Toyota as an example While performing the Zero Point Calibration on Toyota vehicles do not tilt move or shake the vehicle The vehicle must remain in a stationary condition throughout the entire process Be sure to perform the procedure on a level surface with an inclination of less than 1 CG a QHMU If the vehicle is equipped with an A T ensure that the shift lever is in the P range and the parking brake is applied If the vehicle is equipped with a M T ensure that the parking brake is applied Turn the ignition off Locate the vehicle s 16 pin Data Link Connector DLC Plug the scan tool cable connector into the ve
86. ored in non volatile memory and may not be erased by any diagnostic services or by disconnecting power to ECU Use UP DOWN scroll button to select Read Codes from Diagnostic Menu and press OK button Figure 6 3 Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 1 M Readiness 7 02 Monitor Test 8 On Board Monitor Test Figure 6 3 34 2 Use the UP DOWN scroll button to select Stored Codes or Pending Codes from the Read Codes menu and press the OK button Figure 6 4 Read Codes 1 Stored Codes 2 Pending Codes Figure 6 4 e If there is not any Diagnostic Trouble Code the display indicates No pending codes are stored in the module Wait a few seconds or press any key to return to previous screen E NOTE Permanent Codes function is available for merely vehicles supporting the CAN protocols 3 View DTCs and their definitions on screen 4 If more than one DTC is found use the UP DOWN scroll button to check all the codes e If retrieved DTCs contain any manufacturer specific or enhanced codes a Manufacturer specific codes are found Press any key to select vehicle make message comes up prompting you to select vehicle manufacturer to view DTC definitions Use UP DOWN scroll button to select manufacturer and then press OK button to confirm 35 Vehicle Manufacturer BUICK BMW CADILLAC CHEVROLET CHRYSLER FORD Figure 6 5 e Jf th
87. press the OK button 2 Look for missing spots in the red green blue black and white LCD display 3 When completed press the ESC button to exit About The About function allows viewing of some important information such as serial number and software version number of the scanner 1 2 From System Setup screen use the UP DOWN scroll button and LEFT RIGHT scroll button to select About and press the OK button wait for the About screen to appear View tool information on screen Press the ESC button to exit without saving MOT Pro Product Serial Number MCE012000002 Register Password 127289 Firmware Version V1 0 Sys software version V2 10 Hardware Version V1 00 Factory Date 03 08 2012 Copyright c 2012 Autel Co Ltd All rights reserved 3 7 Vehicle Coverage On the basis of all OBD II compliant vehicles including those equipped with universal protocol Control Area Network CAN MOT Pro Scanner expands vehicle system coverage and offers more diagnostic power to the vehicle technicians Featuring expanded global vehicle coverage the scan tool offers technicians a significant improvement on model years covered by supported manufactures In addition to adding new vehicle coverage through 2010 2011 we ve also worked backwards to include non OBDII vehicles which can be diagnosed by setting up with optional OBDI adaptors 3 8 Product Troubleshooting Vehicle Linking Error A communication e
88. r TCS Data and press the OK button to view the data streams ABS Data LF Wheel Speed Sensor 0 RF Wheel Speed Sensor 0 mph LR Wheel Speed Sensor 0 mph RR Wheel Speed Sensor 0 mph Battery Voltage Signal 0 00 Volts Pause One Graphic Save Figure 11 19 3 To view the live PIDs onscreen use the UP DOWN scroll button for all PIDs to display if additional information is available on more than one page The function keys at the bottom of the screen work as below 96 Press the corresponding FUNCTION BUTTON Save to store the retrieved live data for later playback or printing Press the corresponding FUNCTION BUTTON Stop Save to stop saving data and resume live sensor data retrieving Press the corresponding FUNCTION BUTTON Pause to suspend live sensor data retrieving Press the corresponding FUNCTION BUTTON Continue to resume live sensor data retrieving If the One Graphic option is highlighted when a specific item is selected the graphic information is available The PID name current value maximum and minimum values are displayed on the screen When the data is shown in graph the tool offers two more options Two Graphic and Merge Graph The first option can display two graphs on the same screen and the last option can merge the two graphs into one LF Wheel Speed Sensor 0 mph Pause TwoGraphic Save Figure 11 20 Press the ESC button t
89. range the tool will display a warning message Period before service months EW H arning Input Over Flow 5 3 Pre Backspace Figure 9 16 12 v When you have finished your configuration select Finish key on the bottom of the screen then the tool will begin the oil reset service Maintenance Configuration carried out Press any key to continue Figure 9 17 73 10 EPB This electric parking brake EPB function has a multitude of uses to maintain the electronic braking systems safely and effectively The applications include deactivating activating the brake control system assisting with brake fluid control brake diagnostics opening and closing brake pads setting brakes after disc or pad replacement and also reading and clearing EPB SBC trouble codes It is also capable of retrieving Fault Codes information from the ECU 10 1 EPB Safety It may be dangerous to perform electric parking brake EPB system maintenance so before you begin the service work please keep these rules in mind Ensure that you are fully familiar with the braking system and its operation before commencing any work The EPB control system may be required to be deactivated before carrying out any maintenance diagnostic work on the brake system This can be done from the tool menu Only carry out maintenance work when the vehicle is stationary and on level ground Ensure that the EPB control system is reactivat
90. ration is finished successfully the scan tool will display a confirmation message Otherwise it will display a message to remind user of a problem After you exit the diagnosis program please repair the problem immediately Active Test 1 In the Diagnostic Menu Figure 10 20 use the UP DOWN button to select Active Test to do the actuator test The scan tool displays as below qo Active 1 ABS ASR recirculation pump 2 Left front intake solenoid valve 3 Right front intake solenoid valve 4 Left rear intake solenoid valve 5 Right rear intake solenoid valve 6 Switching solenoid valve 1 7 Switching solenoid valve 2 Figure 10 22 2 In the Active menu use the UP DOWN button to select the desired actuator to begin test If the selected actuator works correctly the tool will display a confirmation message as below Figure 10 23 Otherwise it will display a message to remind user of a problem After you exit the diagnosis program please repair the problem immediately Operation completed No fault detected Press any key to continue Figure 10 23 85 11 ABS SRS The ABS SRS diagnostic function is used to retrieve and clear DTCs display and save data streams or module information and perform various function tests on the vehicle s ABS SRS systems It also provides the definition of each trouble code to help diagnose problem areas within the system that have caused the Malfunction Indicator Light to turn on Ei
91. re 12 2 use the UP DOWN scroll button to select Erase Codes and press the OK button 2 A warning message will come up asking for your confirmation DTCs and Freeze Data will be lost Do you wish to continue Figure 12 4 3 Select Yes to continue or No to exit When the command is sent the tool will display a message as below 110 Erase Codes command sent Perform Read Codes function to verify Press any key to continue Figure 12 5 4 To make sure the codes are erased completely perform Read Codes function to verify 12 3 Freeze Frame Data This function allows user to view the vehicle s operating parameters at the moment a DTC is detected 1 From the function menu Figure 12 2 use the UP DOWN scroll button to select Freeze Frame Data and press the OK button 2 View the related operating parameters on screen Freeze Frame Data Steering Pos 1 Parallel Vehicle Speed Vsc ECU 158 mph Engine Revolution Rpm Not Table Data Mtr Power Source Cur 127 5 A Estimated Motor Cur 127 5 A Actuator Position 288 03 deg Figure 12 6 3 Select Save option to store the codes or press ESC button to exit without saving 111 12 4 Live Data This function enables users view SAS related data readings from a selected ECU With the live data screen displayed you can view the data in Text or graphical format record and save files for later viewing pause the readings and view pa
92. re within specified limits These test results are saved in the on board computer s memory The O2 Monitor Test function allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle s on board computer The O2 Monitor Test function is not supported by vehicles which communicate using a controller area network CAN For O2 Monitor Test results of CAN equipped vehicles see chapter On Board Mon Test 1 Use the UP DOWN scroll button to select O2 Monitor Test from Diagnostic Menu and press OK button Figure 6 3 2 Wait a few seconds while the scan tool validates the PID MAP 3 Use the UP DOWN scroll button to select O2 sensor from O2 Monitor Test menu and press OK button Figure 6 23 4 O2 Monitor Test 1 02 Banki Sensor1i 2 02 Banki Sensor2 3 02 Bank2 Sensor1 4 02 Bank2 Sensor2 Figure 6 23 If the vehicle does not support the mode an advisory message will be displayed on the screen Figure 6 24 48 O2 Monitor Test The selected mode is not supported Press any key to continue Figure 6 24 4 View test results of selected O2 sensor Figure 6 25 4 O2 Banki Sensor2 Rich Lean Threshd V Lean Rich Threshd V Low for Switch V High for Switch V Rich Lean Threshd S Lean Rich Threshd S Figure 6 25 5 Use the UP DOWN scroll button to view more data if additional information is available in more than one page 6 Press th
93. rror occurs if the scan tool fails to communicate with the vehicle s ECU Engine Control Unit You need to do the following to check up v Verify that the ignition is ON v Check if the scan tools connector is securely connected to the vehicle s DLC v Turn the ignition off and wait for about 10 seconds Turn the ignition back to on and continue the testing v Verify the control module is not defective Operating Error If the scan tool freezes then an exception occurs or the vehicle s ECU Engine Control Unit is too slow to respond to requests You need to do the following to reset the tool v Reset the scan tool v Turn the ignition off and wait for about 10 seconds Turn the ignition back to on and continue the testing Scan tool doesn t power up If the scan tool won t power up or operates incorrectly in any other way you need to do the following to check up v Check if the scan tool s connector is securely connected to the vehicle s DLC v Check if the DLC pins are bent or broken Clean the DLC pins if necessary v Check vehicle battery to make sure it is still good with at least 8 0 volts 4 Playback Data The Playback Data function allows viewing data from last test recorded by the scan tool E NOTE The amount of files that can be saved depends on the space available in the SD card 4 1 Reviewing Data 1 Use the LEFT RIGHT scroll button to select Playback from Main Screen Figure 3 1
94. s at the bottom of the screen work as below 1 Enter new value for adjustment 2 Reset adjustment to 100 3 End with programming the new value is permanently stored 4 End without programming the old value is retained A Enter new value for adjustment From the Injection rate menu Figure 13 16 use the LEFT RIGHT scroll button to select 1 and press the OK button The screen displays as below You will need to input a new value for injection volume matching 129 Motor Electronics Enter new value for injection volume matching 99 101 Finish Show Esc Figure 13 17 The three keys at the bottom of the screen work as below Finish After entering a new value use this key to save the value to the tool Show Press this key to pop up a soft keyboard to facilitate your input Figure 13 18 Esc Press this key to exit Motor Electronics Pre Backspace Figure 13 18 The three keys at the bottom of the screen work as below Finish When you finished the input select this key to confirm your input and exit Pre Moves a space to the left Backspace Uses this key to erase the previous digit or character when typing 130 E4 NOTE The data you input must be in the reasonable range If the input data is out of range the tool will display a warning message Permissible adjustment range exceeded B Reset adjustment to 100 From the Injection rate menu Figure 13
95. s initiated the DDE cq Motor Electronics The regeneration procedure was successfully requested in DDE control unit Switch off te Motor Electronics 30 seconds elapse befo Start engine continued Particle filter Please wait as the coola off terminal P oR Press ok b exhaust gas The current regeneration status is indicate converter ex in the following step 240 C during The follwing statuses can be observed Optimun reg with this display Regeneration enabled or disabled Regeneration active or not active Attention e 4 Cancel Figure 13 24 135 5 Motor Electronics Current regeneration status REGENERATION ENABLED Regeneration not active Note The display of these statuses may also included in the diagnosis quries of the control unit functions A Figure 13 25 When the particle filter regeneration is complete the tool will ask your confirmation to exit the display Select Repeat to check the status again or End to end the service function and exit Motor Electronics Do you wish to end the display If you wish to repeat the status display press REPEAT button If you wish to end service function press END button End Repeat Figure 13 26 NOTE In the case of a particle filter heavily loaded with soot it can occur that the regeneration request is blocked again after a short time or is not released In this case it is required to regenerate
96. sconnect any test equipment with ignition on or engine running 1 2 3 4 5 6 Turn the ignition off Locate the vehicle s 16 pin Data Link Connector DLC Plug the scan tool cable connector into the vehicle s DLC Turn the ignition on Engine can be off or running Turn on the scan tool Select OBDII in the main screen Figure 3 1 Press the OK button to wait for the Menu to appear A sequence of messages displaying the OBDII protocols will be observed on the display until the vehicle protocol is detected If the scan tool fails to communicate with the vehicle s ECU Engine Control Unit more than three times a LINKING ERROR message shows up on the display Verify that the ignition is ON Check if the scan tools OBD II connector is securely connected to the vehicle s DLC Verify that the vehicle is OBD2 compliant Turn the ignition off and wait for about 10 seconds Turn the ignition back to on and repeat the procedure from step 5 32 If the LINKING ERROR message does not go away then there might be problems for the scan tool to communicate with the vehicle Contact your local distributor or the manufacturer s customer service department for assistance 7 View a summary of system status MIL status DTC counts Monitor status on screen Figure 6 1 Press OK button for Diagnostic Menu Figure 6 3 to come up System Status MIL Status OFF Codes Found 0 Monitors N A 8 Mon
97. st data and more From the function menu Figure 12 2 use the UP DOWN scroll button to select Live Data and press the OK button A All Data 1 From the Live Data menu Figure 12 7 use the UP DOWN scroll button to select All Data and press the OK button 2 The tool will display a list of all live sensor data Figure 12 8 Live Data 1 All Data 2 Custom List Figure 12 7 Live Data Steering Pos 1 Parallel 1854 2 1854 2 deg Steering Pos 1 Parallel Steering Sensor1 Not Table Data Steering Sensor2 Not Table Pause OneGraphic Save Figure 12 8 112 e Press the corresponding FUNCTION BUTTON Save to store the retrieved live data for later playback or printing e Press the corresponding FUNCTION BUTTON Stop Save to stop saving data and resume live sensor data retrieving Press the corresponding FUNCTION BUTTON Pause to suspend live sensor data retrieving e Press the corresponding FUNCTION BUTTON Continue to resume live sensor data retrieving Ifthe One Graphic option is highlighted when a specific item is selected the graphic information is available When the sensor data is shown in graph the tool offers two more options Two Graphic and Merge Graphic The first option can display two graphs on the same screen and the last option can merge the two graphs into one Steering Pos 1 Parallel 185 Steering Pos 2 Ser
98. technician troubleshoot the problem will be erased 94 1 From the diagnostic function menu Figure 11 13 use the UP DOWN scroll button to select Diagnostic Trouble Codes and press the OK button 2 Use the UP DOWN scroll button to select Clear DTC Information and press the OK button Figure 11 14 3 A warning message will come up asking your confirmation Information This ECU has Stored multiple DTCs which may belong to various Functional Systems Freeze Frame Failure Record Data Will be cleared if stored Do you really want to Clear DTC information Yes No Figure 11 16 4 Select Yes to continue or No to exit When the command is sent the tool will display a message as below Information Erase Codes command sent Perform Read Codes function to verify Back Figure 11 17 5 To make sure the codes are erased completely perform Read DTC Information function to verify Data Display 95 This function enables you to view ABS related data readings from a selected ECU With the live data screen displayed you can view the data in Text or graphical format record and save files for later viewing pause the readings and view past data and more 1 From the diagnostic function menu Figure 11 13 use the UP DOWN scroll button to select Data Display and press the OK button Data Display 1 ABS Data 2 TCS Data Figure 11 18 2 Use the UP DOWN scroll button to select ABS Data o
99. through the included CD 2 Connect the scan tool to computer with the USB cable supplied 3 Run MOT Pro Printer software on computer 4 Select Playback function in Main Screen of the scan tool In Scan screen use the UP DOWN scroll button to select the files you want to print Wait for the reviewing window to display Figure 4 2 then select Print function on the bottom The selected file will be uploaded to your computer For more detailed instructions please refer to 4 Playback Data 5 The MOT Pro Printer will show as below S Check Elite Printer Figure 7 1 58 6 The selected data will display on the textbox of MOT Pro Printer By selecting the function keys on the right you could execute the following operations e Print Print all data in the textbox to a printer connected to your computer e Edit Once clicked the software will automatically open an NOTEPAD window with all recorded data showing on e Copy Copy all data in the textbox to the clipboard e Clear Delete all data in the textbox e _ Exit Quit the operation 7 You are also allowed to edit copy and delete the data in the MOT Pro Printer window E NOTE The scan tool can only print text data even though the data is saved in graphic mode 59 8 Software Update This function allows you to update the scan tool software through a computer 8 1 Register the Tool User would update the scan tool ONLY after
100. tion to verify C Data Display This function enables users view SRS related data readings from a selected ECU With the live data screen displayed you can view the data in Text or graphical format record and save files for later viewing pause the readings and view past data and more 1 From the diagnostic function menu Figure 11 26 use the UP DOWN scroll button to select Data Display and press the OK button DEVE MB SIEN 1 SIR Data 2 Module Information Figure 11 31 2 Use the UP DOWN scroll button to select SIR Data and press the OK button to view the data streams SIR Data Battery Voltage 126 Volts Restraints ID 01 Drvr Air Bag Stage 1 0 Ohm Resist s Driver Pretensioner Res 0 Ohm Pause OneGraphic Save Figure 11 32 103 3 To view the live PIDs onscreen use the UP DOWN scroll button for all PIDs to display if additional information is available on more than one page The function keys at the bottom of the screen work as below 4 D Press the corresponding FUNCTION BUTTON Save to store the retrieved live data for later playback or printing Press the corresponding FUNCTION BUTTON Stop Save to stop saving data and resume live sensor data retrieving Press the corresponding FUNCTION BUTTON Pause to suspend live sensor data retrieving Press the corresponding FUNCTION BUTTON Continue to resume live sensor data retrieving
101. ure 13 42 If the engine is not running at 2000 rpm the tool will display a warning message Figure 13 43 Select OK to repeat the test or select Cancel to exit Motor Electronics The engine speed was not maintained during the test Do you wish to repeat the exhaust backpressure test at 2000 rom 01 4 Cancel Figure 13 43 e Check the exhaust backpressure with engine running at cut off speed The tool will read off the actual backpressure value and compare with the upper limit Figure 13 44 Select OK to end the test or Cancel to return to previous menu 145 Motor Electronics Compare actual value and maximum permissible value for approx 10 seconds Actual value 32 0 mbar Maximum permissible value 200 mbar To end test step press OK e 4 Cancel Figure 13 44 If the engine is not running at cut off speed the tool will display a warning message Figure 13 45 Select OK to repeat the test Motor Electronics The engine speed was not maintained during the test Using pedal position sensor maintain engine at cut off speed 10 4 Figure 13 45 The tool will submit a summary report for your confirmation Figure 13 46 Motor Electronics Exhaust backpressure values Idle speed Highest measured value 32 0 mbar Maximum permissible value 35 mbar Engine speed 2000rpm Highest measured value 32 0 mbar Test Selection No Yes Figure 13 46 146 g Select Yes if the actual
102. veuccsusscesiess 8 1 REGISTER THE TOOL 0 ccccccceccccsscesseeeseeeeseesseecsseeeseeenseeeseeesseeesseeneeenaes 8 2 UPDATE PROCEDURE ies seco r a T chest RR RNR 8 3 VIEW OR DELETE PROGRAMG cccscscesscessseeseeseseeesseceseceseeesseeesseenseeenaes OM RESET csc scstiecssscsdccetcessensssasccssesssbacensoansasssesccancerccbesvaesbscesdeassvacsesssnsessesoce 9 1 GENERAL INFORMATION ccccccessesssseesecssseceseeceseceseecesecsseecnseeesseenseeeaaes 9 2 RESET OPERATION oionn it R ERR RON wees ABSISRS wessssstsccsesscascescieceasoatcasesoaseasocshenssuansisecnsenseusesecsonsnsesdascaseasoncscoascasesscbens TVS VEHICLE SELECTION 353ssy eiseeccgevets ons eeatea OE OE obeb oases det dee Vea 11 2 ABS DIAGNOSTICS 55 65 2565 a e sew A R E E 11 3 SRS DIAGNOSTICS 5 ran rninn e AA EA A SAS STEERING ANGLE SENSOR CALIBRATION TZA READ CODES gt ideri a E ERS 12 2 ERASE CODES r aena e AREER E N TAR OTR R STOE 12 3 FREEZE FRAME DATA 124 LIVE DATA S ox re r E E RE E ES 12 5 DUTY r EEE E E E Gases E R R AROA an DPF SERVICE T3517 DPESABETY i505 30s E E edd oo aeons ee aE 132 DPE DIAGNOSTICS e035 s3ieeteseceeeadintate cust han excesses Meee es 13 3 DPF SERVICE FUNCTIONS ccc cccscseesseeeteeeeteeee TPMS TIRE PRESSURE MONITOR SYSTEM cscssscsssssssssssecsssee 14 1 ENTER VEHICLE INFORMATION cccccccssscesseeeecesseceeesseeesseeesseenseeenaes 14 2 TPMS DIAGNOSTICS
103. y sets a code but also records a snapshot of the vehicle operating parameters to help in identifying the problem This set of values is referred to as Freeze Frame Data and may include important engine parameters such as engine RPM vehicle speed air flow engine load fuel pressure fuel trim value engine coolant temperature ignition timing advance or closed loop status 3 Using the Scan Tool 3 1 Tool Description 1 CONNECTOR Connects the scan tool to the vehicle s Data Link Connector DLC 2 SD CARD SLOT Holds the System SD card 3 4 5 6 7 8 9 10 11 LCD DISPLAY Indicates test results TFT color display 320 x 240 dpi FUNCTION BUTTON Corresponds with buttons on screen for executing commands 2 ESC BUTTON Cancels a selection or action from a menu or returns to the previous screen p HELP BUTTON Provides help information and Code Breaker function UP SCROLL BUTTON Moves up through menu and submenu items in menu mode When more than one screen of data is retrieved moves up through the current screen to the previous screens for additional data When looking up DTC it is used to change value of selected character amp DOWN SCROLL BUTTON Moves down through menu and submenu items in menu mode When more than one screen of data is retrieved moves down through the current screen to next screens for additional data When looking up DTC it is used to ch
104. you had registered the tool on our website www autel com Then you could download software update online retrieve information and get warranty service Z NOTE Prior to registration please confirm your network is working properly Visit the website http pro autel com On the Sign In page input your account ID and other information to log in if you already have an account If you are a new member to Autel and do not have an account yet click the Create Autel ID button on the left side Enter the required information in the input fields read through Autel s Terms and Conditions and tick on Agree and then click Create Autel ID at the bottom to continue The online system will automatically send a confirmation email to the registered email address Validate your account by clicking the link provided through the mail A product registration screen opens Select the product model of your device enter the product serial number and password on the Product Registration screen and click Submit to complete the registration procedure NOTE Please use the About function to find out the Product Serial No and Register Password For details please refer to the Section 3 6 System Setup 60 8 2 Update Procedure Autel frequently releases software updates that you can download The Update feature makes it very easy to determine and get exactly what you need 1 2 3 4 Install Autel PC Suit through the includ
105. you visually find the engine oil level or oil change interval has some problems The tool displays as below Press OK button to return to previous menu 139 Motor Electronics Correct oil level if too low Carry out oil change if the oil level is too high or oil change interval has been exceeded A Figure 13 32 d Or select Test Selection to return to previous menu 2 Visual inspection of particulate filter a From the particle filter test menu Figure 13 29 use the LEFT RIGHT scroll button to select 2 and press the OK button Motor Electronics There must be no soot deposits on the inside of the exhaust tail pipes on vehicles equipped with a particle filter Is the inside of the exhaust tail pipes free of soot Test Selection No Yes Figure 13 33 b Select Yes if you visually find no soot on the inside of the exhaust tail pipes The tool displays as below Press OK button to return to previous menu 140 Motor Electronics No fault can currently be found in the compontent group function tested Az Figure 13 34 c Or select No if you visually find soot on the inside of the exhaust tail pipes The tool displays as below Follow the on screen instructions to carry out particle filter visual inspections Then select the correct options according to the test results Motor Electronics Carry out following test Expose the particle filter such that the exhaust flange at the
106. ystem Setup functions allow you to adjust default settings and view information about the scan tool 1 Language Selects the desired language 2 Unit of Measure Sets the unit of measure to English or Metric 3 Beep Set Turns on off beep 4 LCD Test Checks if the LCD display is working properly 5 Key Test Checks if the keyboard is working properly 6 About Provides information of the scan tool e Settings of the unit will remain until change to the existing settings is made To enter the Setup menu From the Main Screen use LEFT RIGHT scroll button to select Setup and press the OK button Following the instructions to do adjustments and settings could make your diagnosis more conveniently and easily Figure 3 2 ume METRIC A Language Unit Beep Y Q aT iuni Key Test Lcd Test About Figure 3 2 Language Setup e English is the default language 12 1 From System Setup screen use the UP DOWN scroll button and LEFT RIGHT scroll button to select Language and press the OK button 2 Use the UP DOWN scroll button to select the desired language and press the OK button to save your selection and return to previous screen Figure 3 3 a x pl E al if English espa ol fran aise Deutsch K Cancel Figure 3 3 Unit of Measure e Metric is the default measurement unit 1 From System Setup screen use the LEFT RIGHT scroll button to select EN METRIC unit and pr

Table of Contents

Contents

Download Pdf Manuals

Related Search

Related Contents