XLED-3MPC_2MPC_Manual_ Rell_ver1
Contents
1. Z Keep the monitor a good distance from any wall to increase circulation of air Increased internal temperature may result in fire electric shock or equipment damage oof Warning to service technician Suitable marking provided on the equipment shall be provided in the servicing instructions to alert a SERVICE TECHNICIAN to a possible hazard where both of the following conditions exist Fuse is used in the neutral of single phase equipment either permanently connected of provided with a non reversible plug After operation of the fuse parts of the equipment that remain energized might represent a hazard during servicing 2 USAGE WARNING Use the enclosed power cord and connect to the standard power outlet of your country Be sure to remainwithin the rated voltage of the power cord Not doing so may result in fire or electric shock Power supply AC100 240V 50 60Hz 1 5 0 7A Make sure to plug the power cord in until it is firmly inserted When S lt C disconnecting the power cord make sure to hold the power plug when pulling the plug from the outlet Tugging on the cord may OK as damage and result in fire or electric shock The monitor must be connected to a grounded main outlet Not doing so may result in fire or electric shock EPI PI USER S MANUAL Use the correct voltage This monitor is designed for use with a specific voltage only Conn2. Il HHHHHHH c US CANICSA C22 2 NO 601 1 This Closs B digital apparatus complies with Canadian ICES 003 WIDE ve Sa Quem cu zer season tinis art Riesen 0 7085 Donaueseingen Gemary sw LEE AE HEU CX30SGH9S0001 3MPC 3Mega 2013 08 Made in Korea EPI eel USERS MANUAL Notice This monitor has been adjusted specifically for use in the region to which it was originally shipped If the product is used outside the region it may not operate in the specifications Please wait 20 40 minutes after powering on the monitor before adjusting as it takes roughly this same amount of time for the optimum performance of the electrical parts The screen may have defective pixels These pixels may appear as slightly light or dark area on the screen This is due to the characteristics of the panel itself and not the monitor The backlight of the LCD panel has a fixed life span When the screen becomes dark or begins to flicker please contact your dealer Do not press on the panel or edge of the frame strongly as this may result in the display malfunction such as the interference patterns etc If pressure is continually applied to the LCD panel it may deteriorate or damage your LCD panel Do not scratch or press on the panel with any sharp objects such as a pencil or pen as this may result in damage on the panel
3. lt Main OSD gt English 25 Accessing the Main OSD e Opening the Main OSD press tj button e Closing the Main OSD press B button on top menu or makes no adjustment for certain period set in the OSD setting gt turns off Menu navigation press P or button Entering the sub menu press button Adjusting the selected function press P or lt button Highlight will move and press button for confirmation then confirmation mark wf will move to the set Main menu Icon Sub menu or item Factory Settings Description DICOM Mode DICOM White USER 6 A DICOM Blue Or F A CT MRI 5 DICOM Mode Ultrasound USER Display Setting Input Modes Auto 6 B SBC 450 6 B Uniformity Max 6 B Enhancement lr N Power Save Enable 6 B LUT Enable Enable 6 B Cooling Fan Speed 20 6 B Self Diagnosis 7 6 B Factory Reset g 6 B OSD Setting Language English 6 C Position Top Right 6 C Transparency Solid 6 C A Turn off 10 sec 6 C Lock out Locked 6 C Rotation Portrait 6 C EPI PI USERS MANUAL Information Information 6 D i Luminance 6 D y Measurement Ambient 6 D Measurement a DICOM Modes Refer to 5 DICOM Mode for more detail b Display Setting Input Mode Auto Input is automatically taken to Mono or Color by input format Mono Input is ta
4. Image systems XLED3MFC XLEDZMFC English User s Manual as Please read this user s manual carefully before attempting to install i this monitor yourself with safe and effective usage AEM Specifications and features are subject to change without notice Images shown are for illustrative purpose only All names of the products are trademarks or registered trademarks of their respective MLEDAMPC omaris 2013 10 ver 1 0 THE CSN SoS XLED3MFC XLEDZMFC English User s Manual Please read this user s manual carefully before attempting to install i this monitor yourself with safe and effective usage Safety Symbol This manual uses the safety symbols below They denote critical information Please read them carefully WARNING Failure to abide by the information in WARNING may result in serious injury or life threatening CAUTION Failure to abide by information in CAUTION may result in moderate injury and or property or product damage ATTENTION Consult accompanying documents The lighting flash with arrowhead symbol in an equilateral triangle is intended to alert the user to the presence of un insulated Dangerous Voltage within the product s enclosure that of many sufficient magnitude to constitute a risk of electric shock to persons Stand by Switch Press to turn the monitor on or off Stand by mode Diagonal line in circle indicates a prohibited action P
5. 60Hz Vsync 60Hz Dot CLK 162MHz Dot CLK 162MHz USB Standard USB specification Rev 2 0 Port Upstream port X 1 Downstream port X 3 Communication Speed 480Mbps 12Mbps 1 5Mbps Plug amp Play VESA DDC2B Power Supply 100 240 Vac 10 1 5 0 7A 50 60Hz Power consumption Typical 80W DPMS Less than 1W Power management NUTEK EET Ze USERS MANUAL Mechanical 1 XLED 3MPC Specification and Regulatory Mechanical Specification Dimension Portrait 378 0mm W X 535 9mm H X 248 8mm D 2 Landscape 506 2mm W X 471 8mm H X 248 8mm D 2 Gross 525 0mm W X 640 0mm H X 320 0mm D 2 Weights Net 11 0Kg 24 25lb Adjustment ability Gross 16 5Kg 36 38lb Environmental Conside Height 0 110mm Rotation 90 Landscape or Portrait Tilt 3 D 15 U Swivel 20 L 20 R ration Operating Temperature 0 C to 40 C 32 F to 104 F Humidity 10 to 80 Maximum Height 5 000mm Atmospheric pressure Range 700hPa to 1060hPa Storage Temperature 20 C to 60 C 40 F to 140 F Humidity 30 to 80 Maximum Height 5 000mm Regulatory Approvals Atmospheric pressure Range 500hPa to 1060hPa UL60601 1 EN60601 1 IEC60601 1 CE VCCI KC C Tick FCC 33 English 2 XLED 2MPC Mechanical Specification Dimension Portrait 378 0mm W X 535 9mm H X 248 8mm D 2 Landscape 506 2mm W X 471 8mm H
6. Do not attempt to brush with tissues as this may scratch the LCD panel When you bring the monitor from cold temperature room into a high temperature room or when your room temperature goes up quickly from low to high dew condensation may occur inside and outside the monitor In this case do not turn on the monitor Please wait till dew condensation disappears Otherwise it may cause some damages to the monitor Prolonged operation of an LCD with the same content on the same screen area may result in a form of image retention You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver You can activate a screen saver in the Display Properties window of your workstation We recommend setting screen saver activation after 5 minutes of non usage In case you are working with the same image or an application with static image elements for several hours continuously so that the screensaver is not activated change the image content regularly to avoid image retention of the static elements 15 English Introduction 1 Features Large display area XLED 3MPC 21 2 XLED 2MPC 21 3 e Multi input support DVI and DisplayPort 30 bits RGB Color signal input support via DisplayPort 10 bits Packed pixel input support via DVI Uniformity Enhancement Function LUC Color calibration with built in color sensor Precise DICOM calibration with 14 bits LUT and bui
7. X 248 8mm D 2 Gross 525 0mm W X 640 0mm H X 320 0mm D 2 Weights Net 11 5Kg 25 35lb Gross 17 0kg 37 48lb Adjustment ability Height 0 110mm Rotation 90 Landscape or Portrait Tilt 3 D 15 U Swivel 20 L 20 R Environmental Consideration Operating Temperature 0 C to 40 C 32 F to 104 F Humidity 10 to 80 Maximum Height 5 000mm Atmospheric pressure Range 700hPa to 1060hPa Storage Temperature 20 C to 60 C 40 F to 140 F Humidity 30 to 80 Maximum Height 5 000mm Atmospheric pressure Range 500hPa to 1060hPa Regulatory Approvals UL60601 1 EN60601 1 IEC60601 1 CE VCCI KC C Tick FCC EET Ze USERS MANUAL Power Management This Power Management System helps you to save energy by switching your monitor into a low power consumption mode when it has not been used for a certain period of time Power Management System operates with VESA DPMS compliant video card installed in your computer You use a software utility installed on your computer to set up this feature We highly recommend setting DPMS activation after 15 minutes non usage in order to optimize your display lifetime and to avoid Image Retention damage We also recommend you not to leave the same image or viewing frame too long Frequent change of moving the image and viewing frame will help you to avoid Image Retention also called Im
8. 8 x 1536 60Hz Compatibility Video card INPUT Specification DVI DisplayPort Power Specification Input connector DVI I 20pin DisplayPort connector Input Signal Dual Link 4 lanes RGB 24 bits or single RGB 30 bits Packed 10 bits Sync Type Hsync 96KHz Hsync 96KHz Vsync 60Hz Vsync 60Hz Dot CLK 260MHz Dot CLK 260MHz USB Standard USB specification Rev 2 0 Port Upstream port X 1 Downstream port X 3 Communication Speed 480Mbps 12Mbps 1 5Mbps Plug amp Play VESA DDC2B Power Supply 100 240 Vac 10 1 5 0 7A 50 60Hz Power consumption Typical 85W DPMS Less than 1W Power management NUTEK 31 English 2 XLED 2MPC Panel Specification LCD Panel 540 0mm 21 3 LCM Mode IPS Pro Response Time 22ms Black gt White gt Black Viewable Image Size 432 0 H mm X 324 0 V mm Display Resolution Portrait Landscape Single Head 1200 x1600 1600 x1200 Dual Head 2400 x 1600 3200 x 1200 Pixel pitch 0 270mm X 0 270mm Brightness 770cd m Contrast Ratio 1100 1 Viewing angle 85 85 85 85 up down right left Compatibility Video card Power Specification UXGA 1600 x 1200 60Hz INPUT Specification DVI DisplayPort Input connector DVI I 20pin DisplayPort connector Input Signal Dual Link 4 lanes RGB 24 bits or single RGB 30 bits Packed 10 bits Sync Type Hsync 75KHz Hsync 75KHz Vsync
9. L EAR BTE V C C 1 OREERT 72 ABlSSEi EIE CT C OREI RE CESS CES BNELTOE TD CORBDIIA PTL EVI YZEL TRAEN SESE 5 amp tec 3 CEDBVET MIRAE CIELUBUURUVE UC REL EPI PI USERS MANUAL PRECAUTIONS 1 INSTALLING WARNING If you see smoke emitting from the monitor if you smell burning or if you hear strange noise out of the monitor you should disconnect all power connections immediately and contact your dealer for the technical advice Attempting to use a faulty monitor may cause fire electric shock or equipment damage Do not attempt to service this monitor yourself as opening or Q Refer all servicing to qualified service technician removing covers may cause fire electric shock or equipment A AN damage Kk Do not open the cabinet or modify the monitor Opening the cabinet or modifying the monitor may result in fire electric mm shock and will void manufacture warranty Do not place this apparatus near or over a radiator or heat resister or where it is exposed to direct sunlight or emitted radioactive sources or electric shock Do not place outdoors in a humid environment or where water can splash on the screen Q Keep liquids away from the monitor as it may result in a risk of fire A Ld Vas i Do not place the monitor in an unstable location such as shaky self a slanted floor or a location exposed to vibration Place the monitor in a strong and stable place English
10. OSD 2 OSD Lock Unlock a Lock out Press cS button and hold for about 5 seconds then the OSD lock message will ap pear if the OSD is locked out properly b Unlock Press button and hold for about 5 seconds then the OSD unlock message will appear if the OSD is unlocked properly 3 Brightness Adjustment a To activate menu Brightenss Adjustment Press 4 or P button in OSD off b Adjusting m Press 4 or P button for decrease or increase value Down 4 M Up 4 LED Lamp brightness Adjustment a To activate menu TED Lamp Brightness M Press 9 button for about 5 seconds in OSD off Sy b Adjusting Press 4 or P button for decrease Down 4 gt Up or increase value EET Ze USERS MANUAL 5 DICOM Mode USER DICOM White Ultrasound a To activate menu Press button in OSD off the DICOM Mode OSD will appear b Adjusting On the DICOM Mode OSD Pressing b button will set the next DICOM mode The default luminance is subject to be changed without notice DICOM Blue CT MRI Gamma Color Temperature Default Luminance DICOM White DICOM Part14 7500 K 450 cd m DICOM Blue DICOM Part14 12500 K 350 cd m CT MRI DICOM Part14 7500 K 350 cd m Ultrasound Gamma 2 2 7500 K 350 cd m mer t eme a Color temperature and gamma as DICOM Mode gt 6 Adjusting the settings on Main OSD DICOM Mode P D Pe
11. U S Government Printing Office Washington DC 20402 Stock Number 004 000 00345 4 User must use shielded signal interface cables to maintain FCC compliance for the product English 2 Declaration of conformity for products Marked with FCC Logo This device complies with Part 15 of the FCC Rules Operation is subject to the following two Conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The party responsible for product compliance Provided with this monitor is a detachable power supply cord with IEC320 style terminations It may be suitable for connection to any UL Listed personal computer with similar configuration Before making the connection make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating For 120 Volt applications use only UL Listed detachable power cord with NEMA configuration 5 15P type parallel blades plug cap For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6 15P type tandem blades plug cap IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations of ICES 003 VCCI Class B ITE COREIA RUB ES SRS S E
12. age Sticky damage on your monitor We manufacturer are not responsible for this damage Power Management Modes State Normal operation DPMS Standby DPMS Suspend DPMS off Horizontal Sync Active Inactive Active Inactive Vertical Sync Active Active Inactive Inactive Video Active Blanked Blanked Blanked x Green Flashing Green Flashing Green Flashing Power Indicat LED off SERERE 3 1sec interval 1sec interval 1sec interval Power XLED 3MPC 85W Less than 1W Less than 1W Less than 1W Consumption XLED 2MPC 80W keyboard Note This monitor automatically returns to normal operation when horizontal and vertical sync return This occurs when you move the computer s mouse or press a key on the 35 English Contact Information Technical Support and Sales Contact TekLink via TekLink Website at http teklink rell com TekLink Phone Toll Free at 888 735 7373 Trouble shooting No picture Make sure that the power cord is completely connected Make sure that the LCD Monitor and computer power switch are on Check the signal cable connector for bent or pushed in pins The display image is too light or too dark Adjust the Brightness or do the factory reset through the Main OSD Screen is blank and power indicator is blinking every 1 seconds Make sure that the signal cable is completely and firmly connected to the display card
13. ation slots prevents proper airflow Do not place in a dusty or an inflammable gas environment as this can result in fire electric shock and equipment damage Use an easily accessible power outlet This will ensure that you can disconnect the power quickly in case of a problem e Periodically clean the area around the plug Dust eater or oil on the plug may result in fire Unplug the monitor before cleaning Cleaning the unit while it is plugged into a power outlet may result in electric shock English Be sure to pull the power plug out of the outlet if the monitor is to remain unused or if you are to leave the office for an extended period of time for the safety and power conservation 13 Double Pole Neutral fusing As an alternative to the above wording use of the following combination of representative symbols which includes the electric shock hazard symbol ISO 3864 NO 5036 the fuse symbol IEC 60417 5016 DB 2002 10 and an indication that the fuse is in the neutral N is permitted However in this case the statement shall also be provided in the servicing instructions Label Statement Canvys a div of CENE Amagesysiems sexes Plymouth MN 55441 LCD Monitor Part Number XLED 3MPC Model CX30TQX Input AC100 240V 50 60Hz 1 5A 0 7A E wU ssp A A uc A Uu a a
14. d and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television receptions which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult a local dealer User Information Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment If necessary consult your dealer or an experienced radio television technician for additional suggestions You may find the booklet called How to identify and Resolve Radio TV Interference problems helpful This booklet was prepared by the Federal Communications commission It is available from the
15. d pull out the wire tie towards your direction 777 E amp Nob TaN 2 WA LE PIN eS eA BN JSE 4 Monitor Positioning Adjust the monitor orientation to your preference with following functions Height Monitor will be shipped in lock position If you want to adjust the height first of all you need to unlock this default position by pushing the lock button located on the bottom of the stand then you will be able to move the head of the monitor up and down Tr 1 ME Lock Botton S Layee eel USERS MANUAL Rotation AN 3 a Z N n SN N X NN Q SN N b N A N M S y N d N Z 4 A A WARNING A Low height adjustment might cause a scratch on surface of the monitor s base stand when rotating monitor Please set the monitor head at high height and pull out the bottom portion of the head toward you before you make rotation This will help you to avoid the scratches on the stand base and around the edges of the monitors You will see the detail instruction sticker on the stand base Follow this instruction Swivel and Tilt English l 23 EHR n 5 Monitor Setting All monitor settings are controlled on OSD Please make sure that the OSD is in the unlock state before adjustment 1 Input Source set Pressing the button toggles between DVI and DisplayPort input The selected input source message will appear on the
16. ection to another voltage different than specified in this user manual may cause fire electric shock or equipment damage Power supply AC100 240V 50 60Hz 1 5 0 7A Do not overload your power circuit as this may result in fire or electric shock Do not touch any signal input signal output or other connectors and the patient simultaneously External equipment intended for connection to signal input signal output or other connectors shall comply with relevant IEC standard e g IEC60950 for IT equipment and IEC60601 series for medical electrical equipment In addition all such combination system shall comply with the standard IEC60601 1 1 safety requirements for medical electrical systems Any person who connects external equipment to signal input signal output or other connectors has formed at system and is therefore responsible for the system to comply with the requirements of IEC60601 1 1 If in doubt contact qualified technician or your local representative WARNING Do not modify this equipment without authorization of the manufacturer To avoid the risk of electric shock this equipment must only be connected to a supply mains with protective earth HEHE UT VRS 77 TRIRIC ORC Bl fT OCC TERY X BEHEUBERC0 PT BAIL LPM SSC 2 RUD S SD ORE UTR bIT2 TES 11 English E Handle the power cord with care Do not place the cord underneath the monitor or other heavy objects Do
17. he presence of flammable anesthetics mixture with air or with oxygen or with nitrous oxide Not suitable for use in the presence of flammable anesthetics mixture with air or with oxygen or with nitrous oxide This equipment has been tested and found to comply with the limits for medical devices to the IEC 60601 1 2 1994 These limits are designed to provide reasonable protection against harmful interference in a typical medical installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to other devices in the vicinity However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to other devices which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving device Increase the separation between the equipment Connect the equipment into an outlet on a circuit different from that to which the other device s are connected Consult the manufacturer or field service technician for help C EPI PI USERS MANUAL FCC Information 1 User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning NOTE This equipment has been teste
18. in the case of returning the product for replacement or repair This ideal package is specially designed and is not easy to find REPE PI USERS MANUAL Safety Introductions General Recommendations Read the safety and operating instructions before operating the display Retain safety and operations for future reference Adhere to all warnings of this display and in the operating instructions manual Follow all instructions for operation and use A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AVERTISSEMENT RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL LCD MONITOR 54D E217340 WITH RESPECT TO ELECTRIC SHOCK FIRE AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL60601 1 AND CAN CSA C22 2 NO 601 1 MEDICAL EQUIPMENT CERTIFIED FOR CANADA Grounding Reliability Can Only Be Achieved When The Equipment Is Connected To An Equivalent Receptacle Marked Hospital Only or Hospital Grade When the unit is used together with other equipment in the patient area the equipment shall be connected according to Standard UL60601 1 and IEC60601 1 English Classification Protection against electric shock Class I Equipment Degree of protection against electric shock No applied parts Degree of protection against the ingress of water ordinary IPXO Degree of safety in t
19. ken to the 10 bits packed Mono by force Color Input is taken to the RGB 24 bits dual link Color by force SBC 250 550 Automatically adjusts the overall light intensity targeting to the Stable selected luminance Brightness USER Automatically adjusts the overall light intensity targeting to the Control luminance set by a user OFF SBC function off Uniformity OFF Uniformity off Enhancement MIN MAX Uniformity level The MAX is the most uniform set Power Save Enable Goes into Power Save mode on the power save condition Disable Doesn t get into Power Save mode on the power save condition Cooling Fan 0 100 Adjusts the cooling fan speed Speed 9 p LUT Enable Enable DICOM LUT enable Disable DICOM LUT disable i e panel gamma itself Self Diagnosis Visual Test It shows test patterns by monitor itself Power Block It checks if the power blocks inside monitor are correct or not Memory Block It checks if the memory blocks inside monitor are correct or not Devices It checks if the devices inside monitor work correctly or not 27 English Factory Reset ALL All of the monitor settings are reset to factory defaults DICOM Mode All of the DICOM Mode settings are reset to factory default Display Setting All settings of the Display Setting are reset to factory default OSD Setting All settings of the OSD Setting are reset to factory default
20. lt in sensor Stable Brightness Control SBC Diverse DICOM Modes for diverse application The height tilt swivel pivot adjustable stand Flexible display Landscape and Portrait mode USB 2 0 Compliance Uptream port X 1 and downstream port X 3 Environmentally Friendly LED Backlights Quick Warm up Reduced waiting time for the monitor to be DICOM complied EPI PI USERS MANUAL 2 Package Contents Please contact your local dealer for assistance if any of the listed items is missing or damaged Monitor DVI Signal Cable DisplayPort Cable Manual amp Power Cord USB Cable USB Driver Installation CD Warranty Card Not Available In All Panel Cleaner Locations English 17 3 Controls and Connectors 1 Front Bottom and Side LED Lamp No Description QD Input Source button G E Menu button 4 Enter button 44 Down Left button P Up Right button 6 Lj LED Lamp on off button Power LED D Abnormal or disconnected signal the LED blinks with green OSD on the LED is green Otherwise the LED is off Warm up function enable the LED is amber b Soft power on off button Color sensor Measuring luminance Y and color coordination x y on DICOM Calibration or col
21. monitor display contain mercury This equipment has required the extraction and use of natural resources for its production It may contain hazardous substances for health and environment In order to avoid the dissemination of those substances in the environment and to diminish the pressure on natural resources we encourage you to use the appropriate take back systems Those systems will reuse or recycle most of the materials of your end of life equipment in a sound way The crossed out wheeled bin symbol invites you to use those systems If you need more information on the collection reuse and recycling systems please contact your local or regional waste administrator You can also contact our nearest representative office for more information on the environmental performances or disposal of our products Cleaning The screen is made of thin glass with a plastic front surface and can be damaged if dropped hit or scratched Do not clean the front panel with keton type materials e g acetone ethyl alcohol toluene ethyl acid methyl or chloride these may damage the panel Panel Clean with a soft woolen or cotton towel Use a watery solution or a mild commercial glass cleaning solution Cabinet Clean with a soft cloth dampened with mild detergent and water Repeat this with water only and wipe dry with a dry cloth Repacking Do not throw away the carton and packing materials We encourage you to keep them for future use
22. not pull on or tie the cord If you notice any external damage on the power cord please stop using it Using a damaged cord may result in fire or electric shock not use any chemicals such as wax benzene alcohol thinners insecticide air freshener This many damage the appearance or erase the printing on the monitor You can clean the LCD monitor with a damp cloth if necessary but be sure to unplug the power cable first Do not touch a damaged LCD panel directly with bare hands Do Keep small objects away from the monitor Small objects can accidently fall through the ventilation slots and into the cabinet which may result in fire electric shock or equipment damage Never touch the plug and power cord if it begins to thunder e outsides Doing so may result in electric shock f EPI PI USERS MANUAL CAUTION Handle with care when carrying or moving the unit Disconnect the power cord and cables when moving the monitor Moving the monitor with the cord connected is dangerous and it maycause harmful injury to you with both hands ensuring the panel faces outward before lifting 9 When handling the monitor grip the bottom of the monitor firmly Dropping the monitor may result in injury or equipment damage d o gt Do not touch the power cord with wet hands Q a Doing so may result in electrical shock Do not block the ventilation slots on the cabinet Blocking the S ventil
23. or calibration Ambient light Sensor Measuring room light on DICOM calibration EET Ze USERS MANUAL 2 Side and Rear Service port DVI I connector DisplayPort Connector USB Up stream USB Down Stream AC Power Input Gees USB Down stream WARNING Connecting a USB to the Service Port 1 may cause a serious damage English 19 Installation 1 Removing the covers Remove the connector compartment cover and stand cover shown in the following pictures EET Ze USERS MANUAL 2 Connecting the cables Connect the power cord to the AC input outlet 6 on the back of the monitor Connect the DVI and DisplayPort cable from PC to 2 and 3 respectively Connect the USB cable to 4 Turn on the monitor and computer Recommended resolution XLED 3MPC QXGA 2048x1536 XLED 2MPC UXGA 1600x1200 English WARNING Use the enclosed power cord and connect to the standard power outlet of your country The equipment must be connected to the grounded main outlet 21 3 Routing the signal cables Please make sure to wire tie and secure all cables behind monitor as shown below If you need to untie the cables press the locking to unlock the mechanisms with your finger an
24. or computer Make sure that the display sources or computer is turned on See page 21 Make sure that the set of monitor input source is what you expect to see as input Check if the monitor is in the power management mode Copyright Notice This document is copyrighted All rights are reserved Neither this document nor any part of it may be reproduced or copied in any form or by any means graphical electronic or mechanical including photocopying taping or information storage and retrieval systems without written permission of Canvys a division of Richardson Electronics O 2013 Canvys a division of Richardson Electronics All rights reserved EPI PI USERS MANUAL
25. rotective earth ground Fragile Handle with care Alternating current English lL wOOGP PPP Direct Current Serial Number Follow instructions for use SN Indicates the manufacturing date e Power supplied equipment can emit electromagnetic waves which could influence limit or result in malfunction of the monitor Please install the equipment in a controlled environment where such effects are avoided e These XLED 3MPC and XLED 2MPC monitors are intended for use in medical image system environment but does not support the display of mammography images for diagnosis For the diagnosis of mammography digital images please contact your local sales representative e Product specifications may vary depending on the sales region Please confirm the specifications within the manual ENDAN USERS MANUAL Table of Contents Safety Symbol Environmental Information Safety Introductions FCC Information VCCI Class B ITE PRECAUTIONS CAUTION Notice Introduction Installation Making use of USB Universal Series Bus Monitor Specifications Mechanical Specification and Regulatory Power Management Trouble shooting English E Environmental Information Disposal Information This product consists of devices that may contain mercury which must be recycled or disposed of in accordance with local state or country laws within this system the backlight lamps in the
26. s c OSD Setting Language Selects OSD language Supported languages English German French Spanish Italian Russian Japanese Chinese and Korean Position Selects OSD Position Top left Top right Center middle Bottom left or Bottom Right Transparency OSD Transparency set Opaque OSD is shown with opaque Transparency OSD is shown with transparent Turn off Adjusts the OSD off time from when the on button is presse Lock out Makes OSD lock or unlock Rotation You can rotate the OSD according to your display rotation d Information Information Model Name The display model name Serial Number The display Serial Number Firmware Version The current internal Firmware version Display Runtime Indicates the total operating time of the display including the time in DPMS Backlight Runtime Indicates the total operating time of the display excluding the time in DPMS Luminance The luminance measured by the IQ Sensor expressed in nit cd m unit Measurement Ambient The ambient light measured by the built in ambient sensor expressed in Measurement Lux unit Layee eel USER S MANUAL Making use of USB Universal Series Bus This monitor provides a hub which supports the USB standard 2 0 When connecting to a USB compliant PC or another hub the monitor functions as a hub to which the USB compliant peripherals can be easily connected Environment Conditions of
27. usage PC equipped with USB ports or another USB hub connected to the USB compliant PC Windows 2000 XP Vista and Windows 7 USB cable enclosed Connection to the USB Hub 1 Connect the monitor to the PC with the signal cable first then turn on the PC 2 Connect the upstream port of the monitor to the downstream port of the USB compliant PC or another hub by using the USB cable 3 After connecting the USB cable the USB function can be set up automatically Connect the USB Compliant PC or another hub using the USB cable 2 i Upstream Port NOTE Install the USB software enclosed CD 29 English E 4 After setting up the monitor s USB hub is available for connecting USB compliant peripherals to the downstream ports of the monitor Downstream Port Connect the cable from USB compliant peripherals such as a mouse keyboard etc EET Ze USERS MANUAL Monitor Specifications 1 XLED 3MPC Panel Specification LCD Panel 539 5mm 21 2 LCM Mode IPS Pro Response Time 22ms Black White Black Viewable Image Size 431 616 H mm X 323 712 V mm Display Resolution Portrait Landscape Single Head 1536 x 2048 2048 x 1536 Dual Head 3072 x 2048 4096 x 1536 Pixel pitch 0 21075mm X 0 21075mm Brightness 900cd m Contrast Ratio 1400 1 Viewing angle QXGA 85 85 85 85 up down right left 204
Download Pdf Manuals
Related Search