Home

UPS-Management Software Benutzerhandbuch

1. Description of Add custom application RCCMO shutdown relay to 192 166 222 4 Relays ROCMD shutdown command to another computer Enter IF address or hostname of the remote computer you want to shutdown cancel Figure 68 RCCMD Shutdown Relay Removal The result of this graphical configuration of an RCCMD relay is found in the shutdown scriptfile shutdown bat Figure 69 RCCMD Shutdown Relay Removal In difference to the above mentioned manual entries of an rccmd shutdown sequence the graphical tool does not use the command start as parameter and therefore the shutdown is taken serially which means one after the other Every IP address which does not respond to such an RCCMD call may take up to 10seconds default until the timeout is reached and the next command is executed 54 3 RCCMD on UNIX with graphical interface The RCCMD remote console command is a program that allows the execution of programs on remote computers This tool is part of all UPSMAN supported operating systems as well as all GENEREX CS121 SNMP Manager BACS Webmanager or RCCMD licensed SNMP Manager of other manufacturers Rittal CMC General Electric SNMP Chloride Masterguard With this tool it is possible to connect different operating systems E g is the UPS Management Software installed on a Unix computer and should a remote shutdown be executed on a computer w
2. v Status Authentication Required e View Event Log A username and password are being requested by http localhost 8080 The site says e System Status RCCMD Config User Name Password E i Figure 88 RCCMD Weblnterface You can enter the IP addresses of the allowed RCCMD senders CS121 UPSMAN into the Connections menu Click the Insert Sender button to enter the IP address of the 68 1 ender Click the Remove Sender button if you want to remove the already entered IP address Click the Edit Sender button if you want to edit the entered IP address Attention If you do not enter an address then every server has the permission to send a shutdown command You can define under Protocol if RCCMD should use SSL certificates Enable the Reject expired SSL certificates if you want to reject connections with expired certificates Please take a look into chapter 6 6 1 for further information about RCCMD with SSL MBOG Connections Mozilla Firefox File Edit View History Bookmarks Tools Help lt a ve A 6 http localhost 8080 Options connections htm v v c Most Visitedv 6 Getting Started latest Headlines v Connections Sp sn 0 0 0 0 0 0 0 1 amp a a a a a a v Options The list below identifies all senders that are allowed to connect to this listener Note An empty list means that every sender can connect to this listener
3. ccccccccccccccccccceesesseeeeeeeeeeeeaeeeeeeeeaeaeaasaaeaaaaaaaaaaaaes 45 Figure 56 UPSMAN Alive Checking Redundancy Window rvvvvvvvvvvvvvvvvvvvvvvvrrvrrvrnrvnnnen 45 Figure 57 Client Check Connection Batch File Window rrrrnrnrrrrrvrvrrrrrerrrrvvrvvvvvvvvvvvevnnnen 46 Figure 58 Check UPSMAN Connections Window rrrrrrrrrrvrrrrrvrrrrrrrrrnnvrrrrvrnvrnnvnrnrrnnnnnnnnnn 47 Figure 59 Configure Edit Bat FileS rrrrnrrnrrnnnnnnnnnnnrrrnvnvvrrrrnnnnnnnnnnnnnrnnnnnnnrrnnrssnnnnnnnnnnnnnnnn 48 Figure 60 FOGD L Fl na SSS 48 Figure 61 RCCMD Email Settings cccccccccccsecceceeeeeeeeeeeeceeeeeeeeeceeeeeeseeeeeaeaeaeeeasaeaeness 49 PIGUI EG 2 CS 121 EA oral 49 Figure 63 RCCMD Shutdown Sequence Configuration ccccccesssssceeseeeeeeeeeeeeeeseeeeeas 50 Figure 64 Example Batch File ROCMD act as Relay Station sorrnnnnnnnnnvrrnnnnnnnnnrrrnnnnnrnnn 52 166 Figure 65 RCCMD Client Shutdown Configuration ccccccccccccccecceecseeeeeeeeeeeeeeeeeeeaeaeaeees 52 Figure 66 RCCMD ShutdowntRel ay ssicccescncnewsccesiinensialasianioiniasiaeasianne 53 Figure 67 RCCMD Configuration IP Address Range ccccceeeeeeeeeeenneenneeeeeeeeeeeeeeeeeeeeeas 53 Figure 68 RCCMD Shutdown Relay Removal cccccceeeeeeeeeeeeeeeeeeeenneeeeeeeeeeeeeeeeeeeeeaas 54 Figure 69 RCCMD Shutdown Relay Removal ccccceeeeeeeeeeeeeeeeeeeenneeeeeeeeeeeeeeeeeeeeaas 54 Figure 70 Installation
4. Add Host 122 4 2 4 1 RCCMD Weblnterface with vCenter After the successful installation with vCenter it is required to enter the access data of the red ESXi hosts via the Edit button and to verify them via the Verify button https 192 168 200 103 3443 Options vmwareSettings htm Cc B Google RCCMD IP 192 168 200 103 mica Virtual Machine behaviour Put Host s into Maintenance Mode v Logout To enable Maintenance Mode enter the vCenter Server credentials v Options Host name or IP 192 168 200 104 e Connections Heartbeats User name root e Redundancy Shutdown Settings Password Notification Settings ae VMware Settings Advanced Settings eck Values Web Configuration The virtual machine that runs RCCMD must not be shutdown Or else RCCMD cannot shutdown the the other virtual machines and hosts Enter the virtual machine s name on which RCCMD runs ESXi Hosts to shutdown ESXi Address Shutdown duration Verified 192 168 200 30 Save Changes Figure 163 RCCMD WeblInterface VMware Settings Edit Host Select Virtual Machine Management by RCCMD if the hosts are managed by a vCenter Server RCCMD must be configured to manage virtual machine handling in case of a shutdown The selection of Virtual Machine Behaviour Shutdown Virtual Machines is the safe choice In this case RCCMD sends a shutdown signal via VMware Tools to the running virtual m
5. Attention The shutdown job would not be executed too if nobody is logged in If this feature is enabled assure that somebody is logged in at anytime gt http localhost 8080 Options advancedSettings htm Datei Bearbeiten Ansicht Favoriten Extras w Favoriten B Web Slice Katalog v Advanced Settings Event Logfile v Options When the event log file reaches the size below then older entries will be deleted Maximum file size KB 512 e Connections Heartbeats Redundancy Shutdown Settings RCCMD Bindings Notification Settings Advanced Settings The information below defines IP address and TCP port of the RCCMD Listener Web Configuration IP address 0 0 0 0 means all addresses 127 0 0 1 6003 Note IP address 0 0 0 0 means every local address default TCP Port is 6003 Message Port Use this Port to send Messages to RCCMD Tray Message Port 961 Start Jobs as interactive User Save Changes Figure 27 RCCMD W ebinterface Configurator Advanced Settings Click the Save Changes button prior of the leaving of this site to save your changes You can change the default password for the user admin into the menu Web Configuration In addition you can disable the HTTPS protocol if you just want to use the HTTP protocol 25 htrp localhost 2080 Optiene webif Management htm Datei Bearbeten Ansicht Favoriten Extras Ge Favoriten 95 E Web S
6. Attention Use the access data User admin Password cs121 snmp 4 v A http localhost 8080 v By Go Most Visited Getting Started Latest Headlines v 6 RCCMD Configurator oP gt Status gt Authentication Required View Event Log ES A username and password are being requested by http localhost 8080 The site says e System Status 7 RCCMD Config Password Figure 179 RCCMD WeblInterface You can enter the IP addresses of the allowed RCCMD senders CS121 UPSMAN into the Connections menu Click the Insert Sender button to enter the IP address of the 1 ender Click the Remove Sender button if you want to remove the already entered IP address Click the Edit Sender button if you want to edit the entered IP address 135 GP Attention If you do not enter an address then every server has the permission to send a shutdown command You can define under Protocol if RCCMD should use SSL certificates Enable the Reject expired SSL certificates if you want to reject connections with expired certificates Please take a look into chapter 6 6 1 for further information about RCCMD with SSL Connections Mozilla Firefox File Edit View History Bookmarks Tools Help lt v e A 6 http localhost 8080 Options connections htm v v Most Visitedv 6 Getting Started latest Headlines v Connections ap a Se 0 0
7. Connections Heartbeats Redundancy 192 168 222 209 Shutdown Settings e Notification Settings stare Web Configuration Enter the Name or IP address of the incoming RCCMD Sender below Incoming RCCMD Sender 192 168 222 210 A Protocol The setting below increases the security of connections to this RCCMD Accept only SSL connections requires restarting RCCMD Reject expired SSL certificates Figure 89 RCCMD W ebinterface Connections Click the Save Changes button prior of the leaving of this site to save your changes You can enable the UPSMAN Alive Check feature into the menu Heartbeats This check is a signal that will be send to the CS121 UPSMAN via port 5769 if the UPSMAN service still got UPS data If not the script file alive bat will be executed which will trigger an accordant pop up message The feature by the use of CS121 UPSMAN Traps provides UPSMAN RCCMD UNMS messages which will display the UPS status as message If enabled this feature will trigger a message if the UPS status of the UPSMAN RCCMD servers has changed The feature by polling CS121 UPSMAN every x seconds provides the pure signal polling without receiving UPS data or rather messages The polling rate default 1800 seconds defines the polling of the UPSMAN service connection retries default 100 means after 100 unsuccessful connection tries an alarm will be triggered
8. Introduction snn aa a a E AAE EAE aE aai 56 Figure 71 Installation License Key rrrnnnnnnnnvnnvrrnnnnnnnnnnvvnnnnnvrnnnnnnnnnnnnsssennnnnnvnnnnnnnnnnnnnssnennee 56 Figure 72 Installation Choose Install Set rrrrrnnnnnrnnnnnrnrrrrrnnnnnnvrnvvrrrvrrrrrrrrrrrrnrnrnrnnnnnnnnn 57 Figure 73 Installation Choose Install Folder rrrrrrrrrrrrrrrrrrrrerrnrrvvvrvvvrvvrrrrrrrrrrrnvrrnnnnnnnen 57 Figure 75 Installation RCCMD Messages rrnnnnnnnnrrrvvnrnrrrrrnnrnnnnnnnnnnnnrrvvnnnnerrrnnnrnnnnnnnnnnnnn 58 Figure 76 Installation Pre Installation Summary rrrrrroroorrrrrrrnnnnnnnnnrrvnnvnnrrrnnnnnnnnnnnnnnennne 59 Figure 77 Installation RCCMD Start Behaviour rrrrrrnrrrrrnnnnrnnnnnnnnrnnnrrrvnnnnersrnnnnnnnnnnnnnnnn 59 Figure 78 Installation Set Weblf Port rrrrrrrrnnnnnnnrrrvvnvrnvrrrrrrnnnrnnnnnnnnrrrvnnnnersnnnnnnnnnnnnnnnnn 60 Figure 79 Installation Configuration AdVice rrnnrrrrrrrnvrrrnnnrrnvnrrrnnnnnrrrrrnnnenerrrrrrrrnnnnnnnnnn 60 Figure 80 Installation Start RCCMD now rrrnnnnnnnrrvvvnvvrrrrnnnnnrnnnnnnnnnnrrvvnnnnressrssnnnnnnnnnnnnn 61 Figure 81 Installation Install Complete rrrrrrrrnrrrrrrrrrrrrrrrvnvvrnnvvrrvvrrrrrrrrrrrrrrnnrnnnnnnnnnnnnnen 61 Figure 80 Content of the installer propertieS cccccssssseeeecccesseeeecsceeesseceessseeaseeeeeseseaes 64 Figure 82 Console Installation Language Selection Introduction rrrrrnrnnnnnnnrnnnnnnnn
9. The following text is presented when entering RCCMD with the help parameter inside a NovellNetW are console Possible parameters listen waits for a command from RCCMD sender sends a ping to a listening program se lt command gt lt param gt sends a command to a listening program 0 por Portadress Defaultadress 6003 149 a lt ipaddress gt Address in IP Format Ex a 192 10 20 30 max t lt timeout gt Time in Seconds Defaulttimeout MAX TIMEOUT this help Supported Commands for use with se argument SHUTDOWN This will call the configured shutdown batchfile default shutdown bat EXECUTE This will call the execute bat file MSG TEXT This will call the message bat file lt text unrestricted word count gt MSG ID lt ID gt This will call the message bat file lt message parameters seperated by blanks gt LOG TEXT This will write to configured log file default reccmd log lt text unrestricted word count LOG ID lt ID gt This will write to configured log file default rccmd log lt message parameters seperated by blanks gt Examples Troad recndenim 8 192 100200 52 4 2927 20 700 253 Load recmda nlm lt 4 et TANN TNT UNS sr 10 load rccmd nlim se SHUTDOWN a 192 10 200 52 Load recnd nim se EXECUTE a 192 10 200 52 load rocnd nlim se MSG TEXT this 15 ness ge d 21020052 150 load rccmd nim 1 road r cndsnim L a 192 10 200452 a 19
10. The polling rate default 1800 seconds defines the polling of the UPSMAN service connection retries default 100 means after 100 unsuccessful connection tries an alarm will be triggered 136 DOG Heartbeats Mozilla Firefox Tools Help File Edit View History Bookmarks Ko vi le A http ocalhost 8080 Options heartbeats htm v 9 7 Google N Most Visitedv 6 Getting Started Latest Headlines v 6 Heartbeats do v Ke 0 0 0 0 0 0 0 1 RCCMD UPS alive check teen CS121 UPSMAN addresses Alive result Ok v Options The UPS alive check can be used to monitor the availabilit Connections bl Enable automatic UPS alive check by the use of CS121 UPSMAN Traps Shutdown Settings An mn amp by polling CS121 UPSMAN every 1800 seco Advanced Settings and retry each failed connection 5 times Web Configuration When the alive check fails then RCCMD will use the follo Run this command file Jusr rccmd rccmd_notalive sh Test UPS connections s Run alive check now Figure 181 RCCMD WeblInterface Heartbeats You can test the UPS connection if you click the Run alive check now button the port 5769 will be tested Click the Save Changes button prior of the leaving of this site to save your changes You can enable the redundancy management feature into the menu Redundancy The redundancy level defines the number of redundant senders
11. with your own e Restart the RCCMD Client Restart the RCCMD Sender 2 7 Settings of the Authorization of the RCCMD Service This function is used for the commitment of the user authorization of the UPSMAN service which exceeds the system shutdown e g execution of batch files script files etc Open the menu of the properties window for the RCCMD service via control panel administration and services 33 rccmd Properties Local Computer HE General Log On Recovery Dependencies Service name recmd Display name beemd Description E Fath to executable CAR CCMDSACCMD EAE Startup type Automatic Service status Stopped Start Stop Pause Resume Tou can specify the start parameters that apply when you start the service from here Start parameters cms Figure 41 RCCMD Properties Window Click the Log On button on the upper left side rccmd Properties Local Computer 7 x General Log On Recovery Dependencies Log on as a a 3 IV Allow service to interact with desktop This account Browse Confirm password fou can enable or disable this service for the hardware profiles listed below Hardware Profile Service Undocked Profile Enabled Docked Profile Enabled Enable Disable Cancel Apply Figure 42 RCCMD Properties Log On Window Check the This account ring and delete the passwords and click the Browse button
12. 192 168 222 209 Insert Sender Protocol The setting below increases the security of connections to this RCCMD Accept only SSL connections requires restarting RCCMD Reject expired SSL certificates Figure 154 RCCMD W ebinterface Connections Click the Save Changes button prior of the leaving of this site to save your changes You can enable the UPSMAN Alive Check feature into the menu Heartbeats This check is a signal that will be send to the CS121 UPSMAN via port 5769 if the UPSMAN service still got UPS data If not the script file alive bat will be executed which will trigger an accordant pop up message The feature by the use of CS121 UPSMAN Traps provides UPSMAN RCCMD UNMS messages which will display the UPS status as message If enabled this feature will trigger a message if the UPS status of the UPSMAN RCCMD servers has changed The feature by polling CS121 UPSMAN every x seconds provides the pure signal polling without receiving UPS data or rather messages The polling rate default 1800 seconds defines the polling of the UPSMAN service connection retries default 100 means after 100 unsuccessful connection tries an alarm will be triggered 117 DOG Heartbeats Mozilla Firefox Tools Help File Edit View History Bookmarks Ko vi le A http ocalhost 8080 Options heartbeats htm v 9 7 Google N Most Visitedv 6 Getting
13. ACCEPT all anywher any state RELATED ESTABLISHED ACCEPT tep anywher anywhere state NEW tcp dpt ssh ACCEPT udp vyuher anywhere ao te NEW udp dpt snmp ACCEPT udp anywher anywhe op ct ct c te NEW udp dpt snmptrap e NEW tcp dpt http ct with icmp host prohibited ACCEPT tep anywher anyi at REJECT all anywhere anywh root vMi41 RCCMD Rom m LJ m Figure 202 Listing of the IP tables see the ACCEPT at the TCP and UDP ports 6003 TCP port 5769 Enable Firewall Port 6003 UDP TCP manually You can enable the firewall port 6003 UDP TCP as follows usr sbin esxcfg firewall esxcfg firewall 0O 6003 tcp in RCCMD receive 6003 158 esxcfg firewall 0 6003 udp in RCCMD receive udp 6003 esxcfg firewall 0O 6003 tcp out ROCMD transmit 6003 esxcfg firewall 0O 6003 udp out RCCMD transmit udp 6003 or usr sbin iptables O sbin iptables iptables I INPUT p tcp dport 6003 j ACCEPT iptables OUTPUT p tcp sport 6003 j ACCEPT iptables I INPUT udp dport 6003 j ACCEPT iptables I OUTPUT p udp sport 6003 j ACCEPT Save your settings as follows service iptable save Problem RCCMD error message on VMware ESXi server 04 25 2012 14 40 24 rccmd 08066 message received from 192 168 2 67 04 25 2012 14 40 24 rccmd 08066 Trying to start program job usr rccmd reccmd shutdown sh 04 25 2012 14 40 24 rccmd 08066 error usr rccmd rccmd_shutdown sh pr
14. In case the user wants to utilise more than one sender address the rccmd sh has to be modified like this bin sh You may specify a sender IP to accept signals from default is everyone SENDER a 10 55 52 82 a 10 55 52 83 a 10 55 52 84 You may change the port to listen on default is 6003 PORT 101 You must define a command to be executed upon receiving signal SCRIPT usr ups doshutdown sh test z SENDER SENDER a SENDER test z PORT PORT p PORT to start rccmd I SENDER PORT SCRIPT UNIX RCCMD multiple sender configuration V3 and higher How to start several RCCMD sessions via different ports on UNIX Every RCCMD session needs an own TCP port e g rccmd l p 6003 rccmd 1l p 6004 rccmd l p 6005 Import into RC files Set an accordant amount of starting scripts and invoke them trough the old ones a Create new starting scripts copy 3 times the old script and rename them cp rceccmdctl sh rccemdctl 1 sh cp rcecmdctl sh rceccemdctl 2 sh cp recmdctl sh recmdetl 3 sh b Adjust the new scripts through the variable RCCMDPORT RCCMDPORT 6003 Adjust the old script because it starts the new one replace the start and stop sector in the folder rccmdetl start usr ups rccmdctl l sh start usr ups rccmdctl 2 sh start usr ups recemdetl 3 8h start ee ry Stop usr ups reccmdctl l sh stop usr ups reocmdeti 2 5h stop usr ups rccmdctl
15. Install Folder C Program Files RCCMD Shortcut Folder C ProgramData Microsoft Windows Start Menu Programs RCCMD Product Features RCCMD Weblf Disk Space Information for Installation Target gt Required 127 365 948 Bytes Available 15 126 745 088 Bytes Figure 17 RCCMD Console Installation Link Location Pre Installation Summary Set the Weblf port and the protocol and RCCMD has been installed successful 18 This is the default protocol to access the RCCMD Weblf Select your preferred protocol here gt 1 http 2 https NTER A GOMMA SEPARATED LIST OF NUMBERS REPRESENTING THE DESIRED CHOICES OR PRESS lt ENTER gt TO ACCEPT THE DEFAULT This is the default network port to access the RCCMD WebIf Belect your preferred port here Port lt DEFAULT 8080 gt Installation Complete ongratulations RCCMD has been successfully installed to C Program Files RCCMD PRESS lt ENTER gt TO EXIT THE INSTALLER Figure 18 RCCMD Console Installation Set Weblf Protocol Port 2 3 RCCMD Weblnterface from version 4 0 1 9 RCCMD provides its own web interface from version 4 0 1 9 or higher Therefore it is possible to configure and control RCCMD remotely After the successful installation as described into chapter 3 1 your default web browser of your OS starts automatically Datei Bearbeiten Ansicht Favoriten Extras ga Favoriten 533 Web Slice Katalog v RCCMD Configurator eee ails 1
16. Program FilesYRCCMD message bat Execute at execute signal from RCCMD server C Program Files RCCMD execute bat UPSMAH y Execute at shutdown signal from RCCMD server C Program Files RCCMD shutdown bat RCCMD ver 4 0 1 7 Figure 59 Configure Edit Bat Files P rccmd log Editor Datei Bearbeiten Format Ansicht Cancel 09 10 2008 03 09 10 2008 03 09 10 2008 03 09 10 2008 08 09 10 2008 09 09 10 2008 10 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 27 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 13 09 10 2008 16 09 10 2008 16 09 10 2008 16 09 10 2008 16 09 10 2008 16 09 10 2008 16 09 10 2008 16 10 17 RCCMD 10 17 RCCMD 10 17 RCCMD 09 10 2008 08 46 37 RCCMD 52 33 RCCMD 08 15 RCCMD 15 24 RCCMD 26 54 RCCMD 26 54 RCCMD 27 01 RCCMD 27 01 RCCMD 27 01 RCCMD 27 01 RCCMD 27 01 RCCMD 27 01 RCCMD 27 28 RCCMD 27 28 RCCMD 27 28 RCCMD 27 32 RCCMD 132 RCCMD 27 32 RCCMD 27 32 RCCMD 27 32 RCCMD 27 32 RCCMD 05 05 RCCMD 38 32 RCCMD 38 33 RCCMD 38 33 RCCMD 38 38 RCCMD 38 38 RCCMD UPSMAN RCCMD Evaluation version testing purpose only this software will stop working in 30 days RevThreadudp started RCCMD Listen Mode start
17. Protocol The setting below increases the security of connections to this RCCMD Reject expired SSL certificates EEE cao Figure 40 SSL Configuration If you want to accept expired certificates please enable the accordant function 32 2 6 1 RCCMD with own SSL certificates In this chapter we will describe how to use an own SSL certificate with RCCMD e g OpenSSL http www openssl org related binaries html Be your own CA Using OpenSSL it is quite simple to become your own CA Just run CA pl newca Done Just ensure that you select a useful CN common name Create your RCCMD certificate You need to create your certificate for RCCMD now As it will use it for verification it should contain the same useful common name CN that you selected for the CA The private key must not be encrypted to let the RCCMD Client service start without trouble Therefore we use the nodes option and the newreq command CA pl newreq nodes Sign with your CA CA pl sign Now create an empty file named rccmd pem and copy the cert information of newcert pem rccmd certificate newkey pem private key and cacert oem CA into it Please note that the exact copying is required to use it without trouble Use your own RCCMD certificate Do the following steps at the RCCMD Client and every sender e g UPS Web Manager Backup the existing rccmd pem e Replace the existing rccmd pem
18. XMessage Please choose the Features to be installed by this installer Please Review the Following Before Continuing Product Name RCCMD Install Folder usr rccmd Product Features RCCMD WebIf XMessage Disk Space Information for Installation Target Required 116 423 910 Bytes Available 3 049 369 600 Bytes PRESS lt ENTER gt TO CONTINUE Figure 84 Console Installation Features Selection 66 It continues with the selection of the RCCMD automatic start Weblf protocol and port Run RCCMD at System Boot Should the RCCMD be automatically started when the System boots gt l OK 2 NO ENTER THE NUMBER OF THE DESIRED CHOICE OR PRESS lt ENTER gt TO ACCEPT THE his is the default protocol to access the RCCMD WebIf Select your preferred protocol here gt 1 http 2 https ENTER A COMMA SEPARATED LIST OF NUMBERS REPRESENTING THE DESIRED CHOICES OR PRESS lt ENTER gt TO ACCEPT THE DEFAULT Set WebIf Port Figure 85 Console Installation RCCMD Autostart Weblf Protocol Port Please note that it is required to configure the RCCMD Software and the required firewall exceptions It is necessary to configure RCCMD Please use the web interface at http lt address of this computer gt 8080 Should you decide to run RCCMD with this default configuration RCCMD will accept messages from any ip address Please set one or more valid ip addresses that are allowed to send shutdown
19. closed again This means that the remote RCCMD received your signal and will execute the shutdown script on the remote side ATTENTION This test will execute the shutdown script If you want to avoid the shutdown please remove the shutdowncommand from the RCCMD client shutdown bat sh file 1s E VWINNT System32 cmd EXE MicrosoftCR gt Windows NTCTM gt lt C gt Copyright 1985 1996 Microsoft Corp DE SIPSMAN rocend a 192 168 2802 52 started in sending mode RCCAD V3 0 Windows NT Remote Command Program copyright c gt QUAZAR GENERES GmbH 1996 All rights reserved 01 99 15 09 53 Send Mode wird gestartet 81 99 15 09 53 Es wird probiert eine Verbindung zu 192 168 2682 52 aufzu 99 15 89 55 Send Mode wird beendet Al 99 15 89 55 Verhindung zu 192 168 202 52 hergestellt Figure 49 RCCMD Console Test 39 2 9 1 Testing the RCCMD 2 connection In order to see under RCCMD 2 if the UPSMAN processes on the remote client are still active the following syntax can be entered via command line rccmd sc ac lt IP address gt C 5RCC HD gt rccmd sc ac 192 168 222 201 started in sending mode ROCMD V4 6 6 7 Windows NT Remote Command Program Copyright c 1996 20667 Generex GmbH RCCND Send Mode started ROCHD Upsman at 192 168 222 261 alive ROOCMD Send Mode stopped LIS AOGGMD gt Figure 50 RCCMD Alive Check via Command Line If the UPSMAN is active the message UPSMAN l
20. els H Client shutdown batch file Look in Ji RCCMD A Name Date modified J inst cfg 08 08 2011 12 12 di jre 08 08 2011 12 12 4 manual 08 08 2011 12 12 J Uninstall RCCMD Client 08 08 2011 12 12 alive 11 04 2003 09 19 4 FET File name shutdown i Files of type Batch files Cancel Open as read only lt Back Install Cancel Figure 57 Client Check Connection Batch File Window ACCMD ver 4 0 1 6 46 If you click the Default setting button you will get back to the default batchfile alive bat At the failure of the UPSMAN alive checking you can define an executing file or edit the default file alive bat file contents as follows echo off rem messagetext 1 ip address 2 date 3 time title c counter for beeps start b msg exe Check Upsman 1 failed 2 3 ATTENTION RCCMD c 1 Click the Next button UPSMAN alive checking UPSMAN address Alive result 192 168 222 201 Successfully connected to UPSMAN Beep endless times 1 to 9 RCCMD ver 4 0 1 7 Figure 58 Check UPSMAN Connections Window Step 7 You can configure the log file size and edit the executing bat files in this installation window 47 Logfile configuration Max logfile size 512 Kb Viewlog Execute at mail signal from RCCMD server C Program Files RCCMD mail bat Configure Execute at message signal from RCCMD server C
21. in which RCCMD is running That means the RCCMD client on the vMA receives a CS121 shutdown and will forward the shutdown command to the ESXi server The vMA provides a management interface for the script based control of the ESXi server RCCMD will be installed on the vMA The RCCMD installer detects automatically that the installation is executed on a VMware application and will install adjusted scrpits for the shutdown DQ Attention The OEM versions of the VMware which got another behavior than the original version will not be supported D Attention RCCMD does not support ESXi 4 x 5 x with free license 105 Enter Name of managed E5Xi Host3 Name or IP address DEFAULT ESXi Host appears to run with free license RCCMD doeschot support ESXi server with free PRESS lt ENTER gt TO CONTINUE Figure 132 ESXi License Error 4 2 1 The ESXi configuration via VMA and vSphere RCCMD will be installed on the vMA The shutdown will be defined at the accordant ESXi host RCCMD will send a shutdown command from the vMA to the ESXi host The following figure shows the RCCMD client on the vMA from where the shutdown to the ESXi hosts will be initiated Virtual Machine Startup and Shutdown x System Settings IV Allow virtual machines to start and stop automatically with the system ESXi Host with ER ee Virtual machine For each virtual machine delay startup for For each virtual machine delay shut
22. set to high AUX 3 0 Port3 set to low AUX 3 1 Port3 set to high 160 AUX 410 AUX 411 Port4 Port4 Syntax for the switching of the outputs of the SiteManager C Program Files RCCMD rcecemd s a 192 168 222 238 p 6002 se UPSCMD 20000 1 1 EXECUTE ATTENTION The blank after the Execute is important Common syntax for the switching of the outputs of the SiteManager UPSCMD 20000 1 0 UPSCMD 20000 1 1 UP5CMD 2000012 0 UPSCMD 20000 271 UPS5CMD 2000013 0 UPSCMD 20000 371 UPSCMD 2000014 0 UPSCMD 20000 4 1 UPSCMD 2000015 0 UPSCMD 20000 5 7 UPSCMD 20000 6 0 UPSCMD 20000 6 1 UPSCMD 2000017 0 UPSCMD 20000 771 UPSCMD 20000 3 0 UPSCMD 20000 8 1 C Know How Pool SuSE 8 1 or older Linux versions If you are using a SuSE 8 1 or an older Linux version it is required to select the OS XEN Server during the interactive RCCMD installation D RARITAN Dominion PDU Configuration In the following we will describe how a RARITAN PDU Type Dominion can be controlled through any RCCMD client or any CS121 or any other RCCMD compatible device 1 Install a RCCMD client on a Windows OS and copy create a file like the following into the RCCMD directory default C Program Files RCCMD and use a SNMPwalk tool from an open source with the mandatory distribution txt file Copying txt This file is included set to low set to high output 1 to output output output output
23. step 3 3 Now you have to select the desired CS121 event and add a RCCMD command which will be send to the Windows computer where RCCMD is running and the pxout bat file is located 162 Me x C5121 SNMP Web Adapter SS EEE we Favorites 33 G CSI21 SNMP Web Ada X amp amp GENEREX Firmware Update fv Ey G dv Pager Safetyy Toosv OJ Stat CS121 Status UPS STATUS OK UPS Information amp setting UPS Status AUX Status AUX Status Job Editor UPS Model amp System T3S Configuration Network amp Security LED Sender RAS Configuration Scheduled Actions SNMP EMail Timeserver SensorManager COM2 amp AUX Events Alarms Save Configuration UPS Major Alarm Added Job 2 Send RCCMD Command to remote client When Immediately once 192 168 200 41 O Scheduledin 0 seconds 6003 seconds pxout bat 192 168 222 43 public2 10 seconds seconds amp repeat seconds on battery Cancel RCCMD Shutdown seconds remaining time S4Command_ UPS Event list CS121 Log UPS Datalog Figure 205 CS121 Configuration for such a relay command The target of the RCCMD command is the Windows computer with RCCMD and the pxout bat with the IP address 192 168 200 41 If the event UPS Major Alarm Added will occur this Job will execute the command pxout bat 192 168 222 43 public2 1 0 to switch off the socket number 1 at the Raritan with the IP add
24. the value 1 corresponds to no HCHOSEN DIALOG BUTTON 0 This variable decides whether RCCMD is started after installer ends Use with care RCCMD should be configured before it is started 0 resembles the answer Yes the value 1 default corresponds to no HCONSOLE START RCCMD NOW 1 Select the language for the installed version of RCCMD by setting the INST LANG variable to the desired country code HH e g el en es de fr he it ja ko pt ru tr zh_cn INST_LANG en Select the destination where the program should be installed HUSER INSTALL DIR usr rcecmd If the target System is a vSphere Management Assistant VMA please provide the name or IP for the ESXi host HESXI HOST 127 0 0 1 Weblf Settings Here you can override default settings for access to the RCCMD Weblf These settings are ignored if the variable CHOSEN_INSTALL_FEATURE_LIST is set and does not contain the Weblf feature In interactive install modes gui console the installer will check whether the chosen port is free to be used Valid values are 1 65535 WEBIF_PORT 8080 Valid protocols are http https 63 WEBIF PROTOCOL http Figure 80 Content of the installer properties It is required to remove the hash mark prior of the variable INSTALLER UI silent In addition the setting of the license key is required behind the variable GXLICENSEKEY Execute the installRCCMD bin
25. v Options When RCCMD shuts down your operating system it will use the following sequence textEditor Connections Heartbeats Redundancy Shutdown Settings C Program Files RCCMD shutdown bat rem created by setup echo off set path path C Program Files RCCMD powershell exe script ps1 cls Notification Settings Advanced Settings Web Configuration Figure 24 RCCMD Weblnterface Configurator Shutdown Settings Edit File You can define the email settings of the sender in the menu E mail Settings In addition you can enable the encryption or rather enter another SMTP port 23 E Mail Settings 0 0 0 0 0 0 0 1 OE Ea setings v Options Configure the sender e mail settings that RCCMD will use to send e mails Connections V Enable E Mail Client Heartbeats Redundancy Outgoing Server SMTP smtp googlemail com Shutdown Settings e E mail Settings Sender E Mail Address generextest amp googlem e Notification Settings Advanced Settings Use Server Authentication Web Configuration Account User Name generextest Account Password oe000000000 SMTP port 25 Y Use secure connection TLS encryption zi dsi Figure 25 RCCMD Weblnterface Configurator E Mail Settings You can change or rather extend the default bat files for E Mail Message and Execute if you click the Edi
26. 0 0 0 0 0 1 a a a a v Options The list below identifies all senders that are allowed to connect to this listener Note An empty list means that every sender can connect to this listener Connections Heartbeats Redundancy 192 168 222 209 Shutdown Settings Notification Settings Web Configuration Enter the Name or IP address of the incoming RCCMD Sender below Incoming RCCMD Sender 192 168 222 210 Protocol The setting below increases the security of connections to this RCCMD Accept only SSL connections requires restarting RCCMD Reject expired SSL certificates Figure 180 RCCMD Weblnterface Connections Click the Save Changes button prior of the leaving of this site to save your changes You can enable the UPSMAN Alive Check feature into the menu Heartbeats This check is a signal that will be send to the CS121 UPSMAN via port 5769 if the UPSMAN service still got UPS data If not the script file alive bat will be executed which will trigger an accordant pop up message The feature by the use of CS121 UPSMAN Traps provides UPSMAN RCCMD UNMS messages which will display the UPS status as message If enabled this feature will trigger a message if the UPS status of the UPSMAN RCCMD servers has changed The feature by polling CS121 UPSMAN every x seconds provides the pure signal polling without receiving UPS data or rather messages
27. 1 RCCMD Installation on UINIX OS 3 2 Silent Installation of the RCCMD Installation 3 3 Console Installation of the RCCMD Installation 3 3 1 Example of a Console Installation 3 4 RCCMD Webinterface from Version 4 2 0 0 3 5 RCCMD Remote Access 3 6 Automatic Reset of the Redundancy Alarm 3 7 RCCMD with SSL for UNIX 3 7 1 RCCMD with own SSL certificates 3 8 Configuration of rccmd cfg file in a non grafical environment 3 9 Older RCCMD Configuration on UNIX OS 3 9 1 RCCMD Client as Relay Station 3 10 UNIX RCCMD Configuration With CURSES Library 4 RCCMD on VMware 4 1 RCCMD on VMware ESX 4 2 RCCMD on VMware ESXi 4 x 5 x 4 2 1 The ESXi configuration via VMA and vSphere 4 2 2 Shutdown configuration of virtual machines on the ESXi host 4 2 3 RCCMD Installation 103 103 105 106 107 109 4 2 3 1 RCCMD Installation without vCenter 112 4 2 3 2 RCCMD Installation with vCenter 112 4 2 4 RCCMD Weblnterface from Version 4 2 0 0 116 4 2 4 1 RCCMD Weblnterface with vCenter 123 4 2 5 Alternative Configuration via Editor 127 5 RCCMD on Citrix XEN Server 128 6 RCCMD on MAC OS 10 X 130 6 1 RCCMD Webinterface from Version 4 2 0 0 135 6 2 RCCMD Remote Access 142 6 3 Old RCCMD Configuration on MAC OSX 143 7 RCCMD on NovellNet Ware 149 8 RCCMD on DEC VMS 153 9 RCCMD AS400 Client 155 10 RCCMD FAQ 156 Appendix 160 A OpenSSL 160 B Syntax for the switching of the outputs 160 C Know How Pool 161 D RARITAN Dominion PDU Configuration
28. 111 111 111 1 relay to 111 111 111 1 relay to 111 111 111 1 message sh Parameter Add custom application pa your session and shuts down System so that you can safely turn off computer Figure 199 Configuration RCCMD Shutdown Sequence RCCMD shutdown relay Relays RCCMD shutdown command to another workstation Enter the IP address or the hostname of the remote station you want to shutdown see chapter 4 4 page 73 Wait seconds Waits a duration in seconds until the next command will be executed Restart System Ends your session shuts down the system and restarts it Shutdown System Ends your session and shuts down the system so that you can safely turn off the power Click the Control button to get into the folowing screen 148 Addresses Functions Logfile Execute Control Control the Rccmd Rccmd status Stop Rccmd Start Rccmd IRCCMDCFG V4 0 0 11 Figure 200 RCCMD Control GP Advice RCCMD provides its own web interface from version 4 2 0 0 or higher Therefore it is possible to configure and control RCCMD remotely Please take a look into chapter 7 for further information 7 RCCMD on NovellNetWare Download the RCCMD netwar5 zip file Extract it to any folder of your Windows or Novell server Create a directory UPS on the Netware SYS Volume e g F UPS Copy the extracted file to this folder Execute the following load rccmd nim L a load down ncf
29. 161 E Figures 165 1 What is the RCCMD Software RCCMD is a network client software which enables to receive shutdowns or messages from UPS servers like UPSMAN UPS Software CS121 SNMP Adapters or any other kind of RCCMD capable network cards of other licenzed partners RCCMD is the successfulliest multiple server shutdown and messaging tool in the entire UPS world 1 1 Network Shutdown with RCCMD The program RCCMD is designed to execute a command on a remote system in a TCP IP network RCCMD works like the Remote Shell RSH known in the Unix environment Inside the UPS Management Software RCCMD is used to shutdown several servers that are all powered by a single UPS For this job one of these computers is configured as UPS master server Install the UPS Management Software UPSMAN on your UPS server and connect it to the UPS Alternatively a SNMP adapter CS 111 or CS 121 can be used for this as well The other servers are only connected to the UPS power supply no RS 232 connection is necessary On these remote systems install RCCMD copy the modules and create a shutdown routine for every system This shutdown routine may be a batch file shell script or ncf file that contains the down and other commands for this system After that add RCCMD to the shutdown job or to the EVENT configuration of the computer running as UPS master server So now you have a computer in your server network supervising the UPS The other servers execute R
30. 3 1 RCCMD Webinterface Remote Access RCCMD provides its own web interface from version 4 0 1 9 or higher Therefore it is possible to configure and control RCCMD remotely Please note that the firewall port 8080 TCP is enabled Enter the following into a web browser to connect to a workstation where RCCMD is running http IP address of the RCCMD client 8080 2 RCCMD Configurator amp 192 168 200 17 30 4 GE NERE v Status Event Log View Event Log These are the events that have occured on this computer System Status Authentifizierung erforderlich Q http 192 168 200 17 8080 verlangt einen Benutzernamen und ein Passwort Ausgabe der Website A RCCMD Config Benutzername Passwort OK Abbrechen Figure 32 RCCMD W ebinterface Configurator Remote Access 2 4 RCCMD Client as Relay Station In order to reach a bigger number of RCCMD receivers one RCCMD client needs to be operated as relay station The receiver will be configured so that it will receive a RCCMD signal and this signal will be used to start a batch file which then starts even more RCCMD sender signals This workstation is then sender and receiver at the same time and is therefore an important link in the UPS monitoring chain Generally the usage of a RCCMD client as a relay station makes the management of several 100 RCCMD clients far easier than configuring this via the Web interface of the
31. 3 sh stop r yr Attention Do not edit the scripts with a Windows editor because the different word wrap of Windows Unix would destroy them 102 4 RCCMD on VMware VMware is manufacturer for virtualization solutions and sales different constructions of those products RCCMD is able to shut down the virtual guest systems AND the VMware physical host systems We descripe the specific features into the following chapters Guest OS ESX RCCMD for VMWare ESX 3 x 4 x Server Guest OS vMotion DRS HA Storage vMotion vCenter Server Guest OS 3 Server license Hardware ESXi freeware not supported by RCCMD Guest OS manager ESXi freeware is managed by the Virtual Infrastructure or vSphere Client not supported by RCCMD Guest OS ESXi RCCMD for VMWare ESXi 4 x Guest OS vMotion DRS HA Storage vMotion VMWare Server freeware Guest OS Workstation Windows or VMWare Workstation Guest OS User Hardware Linux OS Guest OS RCCMD Linux Session ee ee Windows vSphere Client for managing ESX i hosts freeware Figure 131 VMware Products RCCMD is able to shut down the products ESX and ESXi The RCCMD software supports the VMware ESX and VMware ESXi The VMware ESX is liable to pay ciosts always and contains an integrated Linux desktop VMware ESXi is available for free too and is an operating system which is embedded in another system with web interface We descripe the respective differences in the usage
32. 34 D v phere Management Agasi TEC EET T Virtual Machines Resource Allocation Performance C orig jon Hardware Virtual Machine Startup and Shutdown Heatth Status Start and Stop Virtual Machines with the system Enabled 5 s Default Startup Delay 10 seconds Er Default Shutdown Delay 30 seconds Hemory Storage Startup Order Order Wtusl Machine Statup Setup Delsy Shutdown Shutdown Delay Networking 4 FARE iz gt Coe Managem Enabled 10 seconds Sht 30 seconds i a Network Adapters a L gam somn Adverned Settings Software Licensed Features Time Configuration DNS and Routing 3 Status Details Indiated by Requested Start Ti Kart Tine Completed Tine rake Evahaston Mode 60 days remaining root Figure 134 vSphere Client Configuration Select into the properties dialog the vMA and set its values to 10 seconds start delay and 30 seconds shutdown delay Virtual Machine Startup and Shutdown i xj System Settings M Allow virtual machines to start and stop automatically with the system Default Shutdown Delay For each virtual machine delay shutdown For fso seconds Shutdown Action Guest Shutdown Default Startup Delay For each virtual machine delay startup for fio seconds IV Continue immediately if the VMware Tools start Startup Order Power on the specified virtual machines when the system starts During shutdown they will be stopped in the opposite order O
33. 48 or higher Login as root and mount the CD ROM on the XEN Server Enter mount dev cdrom media Since it s a CD ROM in your driver the system will respond mount block device dev cdrom is write protected mounting read only Change to the CD ROM by cd media by Is you can see the files on the CD change now to the folder UNIX UPSMAN CD ROM or generex until you find the installationprogramm install Start now the installation by entering install and follow the instructions on the screen from here the installation is identical to any other RCCMD installation for UNIX After the installation is finished a new process will be running on your XEN Server rccmd which means the system is ready now ATTENTION XEN Server has per default a firewall active which does not allow to send from remote RCCMD signals To open this firewall you have to edit the file iptables etc sysconfig Firewall Configuration Add the following lines to etc sysconfig iptables before the last REJECT rule 129 4 RH Firewall 1 INFOT p udp dport 6005 3 ACCEPT 4 RH Firewall 1 INFOT p tep dport 6005 j ACCEPT 4 RH Firewall 1 INFOT j REJECT reject vith icmp host prohibited COMMIT fetc syscontig iptables readonly 25L 1215 Figure 169 Firewall Configuration Restart the iptables using etc init d iptables restart RCCMD is now listening and will start t
34. Are you satisfied with the backup of your system disk YEST e Answer the prompt Where will the distribution volumes be mounted with your correct input device name e g CDROM dka500 VMS your CDROM device and path VMS the device may be different on your system Answer the prompt Enter installation options you wish to use none by pressing RETURN e Atthe prompt Please mount the first volume of the set on MKA300 Are you ready please insert your tape or disk or CDROM and answer yes Enter the license key of your RCCMD version Enter the complete path of the target directory e g dka100 ups e Answer the question Would you like to start the RCCMD module automatically on your system e Exit the VMSINSTALL procedure by RETURN at the Product prompt and change to your target UPS directory e g set default dka100 ups e Now install the RCCMD software in sending mode on your RCCMD server workstation Your server workstation is the computer which is connected to the UPS via the RS232 port DEC ALPHA CD Problems If the CD could not be mounted or if you have problems to start the VMSINSTAL script on the DEC ALPHA hardware please follow the instructions below 154 e Copy the archive VMSA ZIP ALPHA directory into a temporary directory on your system COPY RCCMD ZIP DKA100 TEMP If you have not installed the ZIP utilities on your workstation already you
35. Cinfinite gt gt Figure 51 RCCMD Console 40 2 10 RCCMD on Windows 95 98 RCCMD for Windows 95 98 functions similar to RCCMD on Windows NT The only difference is the program name which changes to RCCMD95 EXE Please also refer to the RCCMD Windows section of this manual D Attention For Windows 95 98 users we do recommend the installation of the TCP IP protocol first and then run the configuration program making use of the RCCMD WIZARD D Attention In case Winpop exe is used on Windows 95 98 RCCMD can not be started on port 6003 otherwise the computer will hang up Please change the sender and receiver call up accordingly Experienced users may use the registry editor and enter all changes manually Unexperiecend users should use the RCCMD wizard Registry settings Please check the following In order to start the RCCMD process in Listen mode the RCCMD parameter have to be entered in the registration database Please enter regedit exe rccmd95 reg or simply start rc init bat The parameters are now located under the registration key HKEY LOCAL _MACHINE CurrentControlSet Services RCCMD95 Parameters Start regedit exe again if you want to reconfigure RCCMD If you are unfamiliar with the registration editor of Windows 95 you can also modify the file rccma95 reg and execute the command regedit exe rccmd95 reg again Parameters Port Special TCP Port that receives the RCCMD signal Addr1 10 TCP IP address of
36. Congratulations RCCMD Client has been successfully installed to C Program Files RCCMD Press Done to quit the installer Figure 12 Installation Complete 2 1 1 Silent Installation of the RCCMD Installation The RCCMD Software provides a silent installation but it is required to enter some settings into the Installer Properties file This file is located into the CD folder Recmd W indows 1 2 Usage To record a new response file start the installer from command line with parameter r Use the new Values for the provided Variables from this file To perform a silent install start the installer on the commandline The installer also needs the parameters f lt path to resonsefile gt Choose Install Folder Uncomment this variable to set a new default Folder into which the program will be installed The example represents the default that will be used if no folder is provided According to the example backslash characters V need to be escaped by a backslash Spaces in the path also require a backslash as an escape character Hit USER_INSTALL_DIR C RCCMD Choose Link Location You can tell the installer in which folder the shortcuts should be installed The absolute path must be given options are Do Not Install if you do not want any shortcuts or a path to the folder in which the shortcuts should be created Here are two examples USER SHORTC
37. Network Options In this screen you may configure network related options of the rccmd listener To switch between the option fields and buttons use the Tab key generex host usr ups Rcecad Network Options Bind on Interface 0 0 0 0 Listen on Port Enable UDP listen for rccmd broadcasts true Timeout Connections after seconds 10 Cancel Default Figure 120 RCCMD UNIX Network Options Bind on Interface This option tells rccmd on which network interface it binds its main tcp listen socket You may enter any valid IP address your host can be reached The default value for this option is 0 0 0 0 this is a working value it means listen on all possible interfaces of this host If your host has a dial up connection to the internet you may want to change the default to ensure rccmd will not be connected from the internet In this case you will enter the primary IP address of the host rccmd listener is running on Example 92 Your company runs a private network in the 192 168 1 0 24 address range The host rccmd listener is running on is assigned the IP 192 168 1 9 You may enter 192 168 1 9 for Bind on Interface to ensure only host from the private network can connect to rccmd Listen on Port This is the port rccmd will listen to Allowed values range from 1 to 65535 inclusive The default is 6003 If you change the port of the rccmd listener you will also have to switch the port of
38. On off Cycle 0 00 Amps 0 Watts Connected Users Outlet3 on On Off Cycle 0 00 Amps 0 Watts admin 192 168 200 41 Seay on Lor Levee 3 min idle Outlet4 on On off Cycle 0 00 Amps 0 Watts Poner Cima Si Outlet 5 on On off Cycle 0 00 Amps 0 Watts Power CIM is enabled Outlet 6 on On off Cycle 0 00 Amps 0 Watts Help User Guide Outlet 7 on On off Cycle 0 00 Amps 0 Watts Outlets Figure 206 Raritan Device Settings The default Raritan user is admin password is nimda D Attention This does not work with MS Internet Explorer Use any other web browser e g Mozilla Firefox gt SM 192168 222 43 https 192 168 222 43 home asp SE Raritan rermbi lt lt Ex Dominion PX Home gt Device Settings gt SNMP Settings Time amp Session 2000 01 23 02 06 SNMP Settings Enable SNMP Agent User admin State active Your IP 192 168 200 41 Last Login 2000 01 23 00 49 Enable SNMP v1 v2c Protocol Read Community Device Information public ae ae 16 bd mr I el PX Di 16 public2 IP Address 192 168 222 43 Firmware 01 04 01 F Enable SNMP v3 Protocol Firmware Status OK Force Encryption System Location Here Connected Users admin 192 168 200 41 acie System Contact Power Cim State Power CIM is enabled Click here to view the PX DPXS12A 16 SNMP MIB Help User Guide Apply Res
39. RCCMD cancel shutdown to discard a previously sent shutdown automatically If a shutdown was suppressed because of the existing redundancy at this point of time but the problem was solved at the UPS intermediate you can reset the shutdown with the function Send RCCMD cancel shutdown The client which received the shutdown will be encouraged to reset it This command can be set individually into your CS121 UPSMAN or BACS WEBMANAGER Events Alarms configuration but makes sense only if the event which will send the command is true if the UPS is back in normal condition For this the events POWER RESTORED BATTERY LOW OFF UPSMAN STARTED and GENERAL ALARM OFF are suitable if they are provided from your UPS into the CS121 The job Send RCCMD cancel shutdown would be set into these all clear events so that e g at restart of the UPS the event UPSMAN STARTED would reset the accordant RCCMD client automatically Alternative Should the job Send RCCMD cancel shutdown not be present into your CS121 UPSMAN or BACS WEBMANAGER you can use the job Send RCCMD shutdown to remote client or rather Send RCCMD execute to remote client alternatively The parameter WAKEUP got the same function like the Send RCCMD cancel shutdown and resets the redundancy alarm of a RCCMD Client into initial state For this the events POWER RESTORED BATTERY LOW OFF UPSMAN STARTED and GENERAL ALARM OFF are suita
40. Settings Protocol Advanced Settings Note Changes in protocol will become active upon the next start up Web Configuration Port for http 8080 Port for https 8443 Done Figure 186 RCCMD WeblInterface Web Access 140 Click the Save Changes button prior of the leaving of this site to save your changes You can see the logging of the events into the menu Status Event Log DOG RCCMD Configurator Mozilla Firefox story Bookmarks To lt v amp a http focalhost 8080 Status viewEventLog htm v SB v Goog N Most Visitedv 6 Getting Started Latest Headlines v 6 RCCMD Configurator oF v 0 0 0 0 0 0 0 1 Y Status Event Log e View Event Log These are the events that have occured on this computer System Status Date a Time FEN 2012 10 18 15 23 22 rccmd 03915 Copyright c GENEREX GmbH 1996 2010 All rights reserved 2012 10 18 15 23 22 rccmd 03915 UPSMAN RCCMD MASTERKEYCODE testing purpose only do not use for customer installations 2012 10 18 15 23 22 rccmd 03915 V4 2 3 0 Unix Remote Command Program 2012 10 18 15 23 23 rccmd 03923 Listen Mode started 2012 10 18 15 23 23 rccmd 03923 RevThreadUdp started Done Figure 187 RCCMD Weblnterface Event Log You can check the current status of RCCMD into the menu Status System Status update the status and restart or rather stop start the RCCMD service DOG System Status Mo
41. Started Latest Headlines v 6 Heartbeats do v GENEREX 0 0 0 0 0 0 0 1 RCCMD UPS alive check teen CS121 UPSMAN addresses Alive result Ok v Options The UPS alive check can be used to monitor the availabilit Connections bl Enable automatic UPS alive check by the use of CS121 UPSMAN Traps Shutdown Settings An mn amp by polling CS121 UPSMAN every 1800 seco Advanced Settings and retry each failed connection 5 times Web Configuration When the alive check fails then RCCMD will use the follo Run this command file Jusr rccmd rccmd_notalive sh Test UPS connections s Run alive check now Figure 155 RCCMD Weblnterface Heartbeats You can test the UPS connection if you click the Run alive check now button the port 5769 will be tested Click the Save Changes button prior of the leaving of this site to save your changes You can enable the redundancy management feature into the menu Redundancy The redundancy level defines the number of redundant senders in the redundancy group This means that level 1 senders must have sent a shutdown signal before this RCCMD starts its shutdown sequence When redundancy suppresses a shutdown then RCCMD will trigger the suppressed bat You can edit this file if you click the Edit file button 118 Redundancy Mozilla Firefox v g A 6 http localhost 8080 Options redundancy
42. Tray Description Added Raritan Dominion PDU Configuration Added RCCMD on ESXi 5 Added RCCMD WebInterface Added RCCMD with VMware vCenter Added RCCMD Installation with vCenter Date 10 2008 11 2008 12 2008 01 2009 02 2009 03 2009 03 2009 06 2009 07 2009 08 2009 08 2009 10 2009 11 2009 11 2009 11 2009 11 2009 01 2010 03 2010 07 2010 08 2010 11 2010 06 2011 09 2011 10 2011 04 2012 08 2012 08 2014 Table of contents 1 What is the RCCMD Software 1 1 Network Shutdown with RCCMD 2 Installation Configuration of RCCMD for Windows 2 1 Installation of RCCMD 2 1 1 Silent Installation of the RCCMD Installation 2 1 2 RCCMD Silent Installation and Takeover of own Configuration 2 2 Console Installation of the RCCMD Installation 2 2 1 Example of a Console Installation 2 3 RCCMD Webinterface from version 4 0 1 9 2 3 1 RCCMD Webinterface Remote Access 2 4 RCCMD Client as Relay Station 2 5 Automatic Reset of the Redundancy Alarm 2 6 RCCMD with SSL for Windows 2 6 1 RCCMD with own SSL certificates 2 7 Settings of the Authorization of the RCCMD Service 2 8 Testing of the Shutdown Bat File 2 9 Testing the RCCMD connection 2 9 1 Testing the RCCMD 2 connection 2 10 RCCMD on Windows 95 98 2 11 RCCMD for Windows NT 2000 XP 2003 2008 2 12 RCCMD for Windows 2008 Server Core x64 2 13 Older RCCMD Configuration 2 13 1 RCCMD Client as Relay Station 3 RCCMD on UNIX with graphical interface 3
43. by default rem created by setup echo off set path path C Program Files RCCMD ExitWin exe shutdown force clis 119 DOG Shutdown Settings Mozilla Firefox i v e A E http Nocalhost 8080 Options shutdownSettir ngs htm ov tv Googl fi Most Visited Getting Started BJLatest Headlines v Shutdown Settings Ae v sn ee v Options When RCCMD shuts down your operating system it will use the following sequence te Heartbeats Redundancy Shut down System Settings file lusrirccmdlrccmd shutdown sh Figure 157 RCCMD W ebinterface Shutdown Settings You can change or rather extend the default bat files for E Mail Message and Execute if you click the Edit File button DOG notification Settings Mozilla Firefox lt a v A http localhost 8088 Options notificationSettings htm v v Goog Q Most Visitedv 6 Getting Started Latest Headlines v 6 Notification Settings op 0 0 0 0 0 0 0 1 v Options When RCCMD receives an e mail signal it will use the following setting Run this command file lusrirccmdlrccmd mail sh Notification Settings Advanced Settings Message Notification Web Configuration When RCCMD receives a message signal it will use the following setting Run this command file lusrirccmdlrccmd message sh Execute Notification When RCCMD receives an execute notification it will use the following setting R
44. contains the installation data Extract the the rccm dinst tar file tar xvf recmdinst tar Execute the binary file installRCCMD bin 157 Problem The RCCMD Software does not execute RCCMD shutdowns and you can determine the following error message into the file rccmd log default folder C Program Files RCCMD 11 23 2011 12 56 55 RCCMD ERR WaitForOkay Read failed with error lt 0 gt Solution Update your RCCMD Software Problem You got the following error into the CS121 alarm log 12 06 2011 16730256 RCCMD could not connect ReemdConndl Reason Host prohibited Solution The server denied an incoming TCP connection Check your firewall configuration Problem Enable firewall ports manually Solution You can check if the required ports were opened with the following command sudo iptables L Chain INPUT policy ACCEPT Ot opt source LCCEPT CCEPT adp 1er anywher udp dpt 6 tcp dpt 60 Chain FORWARD policy ACCEPT target prot opt source destination RH Firewall 1 INPUT all anywher any Chain OUTPUT policy ACCEPT target prot opt source destination Chain RH Firewall 1 INPUT 2 references target prot opt source destination ACCEPT all anywher anywhere ACCEPT icmp anywher anywhere icmp any ACCEPT esp anywher anywhere ACCEPT ah anywher anywhere ACCEPT udp anywher 224 0 0 251 udp dptimdns ACCEPT udp anywher anywhere udp dpt ipp ACCEPT tep ywher anywhere tcp dpt ipp
45. delete the entry by selecting Ok with the Tab key and pressing Enter otherwise select Cancel To leave the screen select either Ok or Cancel with the Tab key and press Enter Ok means accept the list as displayed on the screen Cancel means discard all changes made to the list Scan for Upsman Upstcp This screen allows you to scan your network for Upsman Upstcp servers You may want to add the detected IP addresses to the Access Control List D Note The options on this screen do not directly affect rccmd However the results of a network scan may be transferred to the Access Control List 96 E generex host usr ups Scan Options lowest IP 10 64 64 1P highest IP 10 64 64 254 Port to scan 5769 Cancel Figure 126 RCCMD UNIX Sender Scan lowest highest IP On startup rccmd conf tries to determine the hosts primary IP address From this address a corresponding Class C network range is derived These are the default boundaries for the network scan If you want to scan another network or adjust the range move to the desired entry lowest and or highest IP using the Tab key and change the address as appropriate Port to Scan The port the scanner will try to connect to The default is 5769 which is the default port of the Upsman Upsicp server If you have Upsman Upstcp running on a different port you may want to switch this option accordingly To start the scan select Sca
46. file as root Further installation options are for a non grafical user input console or to use the graphical installation default 3 3 Console Installation of the RCCMD Installation A console installation is required if your target operating system does not have a grafical interface for the execution of the instalIRCCMD bin This console installation works interactive and will ask for user input defined in the installation script file installer properties see figure 62 Note This concerns the installation only The configuration will be performed via editor into the rccmd cfg file For the activation of the console installation it is required to remove the hash mark prior of the variable INSTALLER UI and to enter console This is the interactive RCCMD installation onto the console Execute as root the installRCCMD bin file 3 3 1 Example of a Console Installation Adjust the file installer properties accordingly like described above or execute the following command installRCCMD bin i console Select the desired language and note the introduction 64 Launching installer Deutsch English Espafiol Francais Italiano Portugu s LOCALE BY NUMBER 2 InstallAnywhere will guide you through the installation of RCCMD Client It is strongly recommended that you quit all programs before continuing with this installation Respond to each prompt to proceed to the next step in the insta
47. install modes gui console the installer will check whether the chosen port is free to be used Valid values are 1 65535 WEBIF_PORT 8080 Valid protocols are http https WEBIF PROTOCOL http Figure 13 Content of the installer properties It is required to remove the hash mark prior of the variable INSTALLER UI silent In addition the setting of the license key is required behind the variable GXLICENSEKEY 2 1 2 RCCMD Silent Installation and Takeover of own Configuration After you have finished the edition of the installer properties file it is possible to create an own RCCMD configuration and to silent install Thereto it is required to execute the RCCMD configuration manually once Then export this configuration out of the registry into a file as follows Click the right mouse button on Parameters into the directory HKEY_ LOCAL_MACHINE SYSTEM CurrentControlSet Services rccmd select Export and save the file with the name rccmd reg as WIN95 NT4 Registration File e Store the file rccmd reg into the directory where the RCCMD Installer packet is located e Open the file rccmd reg with an editor and delete the complete line which contains the license key e Create a new Windows batch file bat with an editor e g with the name InstalAndConfigRCCMD bat which should look like as follows Now you can start a combined RCCMD silent install
48. messages to this RCCMD PRESS lt ENTER gt TO CONTINUE Required Firewall Exceptions Make sure following Ports are not blocked by any firewall Ports 8080 tcp WebIf Server if installed Ports 6003 amp 5769 tcp udp RCCMD PRESS lt ENTER gt TO CONTINUE Figure 86 Console Installation RCCMD Configuration required Firewall Exceptions Do you want to run RCCMD now 67 It is recommended to start RCCMD from WebIf after all necessary configuration If you want to start it manually use usr rccmd rccmdctl start or start it via the web interface Do you want to start RCCMD now gt 1 OK 2 NO ENTER THE NUMBER OF THE DESIRED CHOICE OR PRESS lt ENTER gt TO ACCEPT THE DEFAULT Congratulations RCCMD Client has been successfully installed to usr rccmd PRESS lt ENTER gt TO EXIT THE INSTALLER Figure 87 Console Installation RCCMD Start Installation Complete 3 4 RCCMD Weblnterface from Version 4 2 0 0 RCCMD provides its own web interface from version 4 2 0 0 or higher Therefore it is possible to configure and control RCCMD remotely After the successful installation your default web browser of your OS starts automatically Attention Use the access data User admin Password cs121 snmp File Edit View History Bookmarks Tools Help lt v E A 0 http localhost 8080 v 7 Most Visited 6 Getting Started Latest Headlines v 6 RCCMD Configurator op
49. must be also in lt AliveAddresses gt Seperate IP addresses with a space e g 192 168 0 1 192 168 0 2 Default lt empty gt No redundancy available Redundancy Addresses Redundancy Level Defines how many of the lt RedundancyAddresses gt are redundant Shutdown is executed when the number of shutdown requests exceeds this number Default 0 No redundancy available RedundancyLevel 0 Enable Redundancy Script Defines if we should NOT execute a script when redundancy suppresses a shutdown 82 Default false RedundancyBatchSuppress false Redundancy Script Full path to script that is executed when redundancy suppresses a shutdown Default ShutdownSuppressed sh RedundancyBatchFile 3 9 Older RCCMD Configuration on UNIX OS If no entries are changed in this default rccmd cfg file all incoming RCCMD commands will be executed from any sender and use the default shutdown scriptfile rccmd_shutdown sh Add the IP address of the RCCMD server which is allowed to send a shutdown to this client RCCMD Configuration x Addresses Functions Logfile i Execute Control IP address list of all RCCMD servers that are allowed to send shutdown command to this client no entry means every server Add Address IP address or name IRCCMDCFG V4 0 0 11 ei Figure 107 Configuration RCCMD Sender IP Address Attention If yo
50. op v 0 0 0 0 0 0 0 1 v Options When RCCMD receives an e mail signal it will use the following setting Run this command file Jusrirccmd rccmd_mail sh Advanced Settings Message Notification Web Configuration When RCCMD receives a message signal it will use the following setting Run this command file fusrirccmd irccmd_message sh Execute Notification When RCCMD receives an execute notification it will use the following setting Run this command file fusrirccmd rccmd_execute sh Edit File Nane Figure 184 RCCMD Weblnterface Notification Settings Click the Save Changes button prior of the leaving of this site to save your changes You can define the maximum size of the event logfile into the menu Advanced Settings where the overwriting of older entries will start the RCCMD bindings for the IP address the RCCMD listener TCP port and the RCCMD Tray Message Port which will be used for the RCCMD messages In addition you can disable the Start Jobs as interactive user feature that means if disabled that RCCMD will execute jobs if nobody is logged in on the system 139 DOG Advanced Settings Mozilla Firefox lt a v E A http localhost 8080 Options advancedSettings htm v Google Q Most Visitedv Getting Started latest Headlines v 6 Advanced Settings op v 0 0 0 0 0 0 0 1 v Options When the event log fil
51. senders CS121 UPSMAN into the Connections menu Click the Insert Sender button to enter the IP address of the 1 ender Click the Remove Sender button if you want to remove the already entered IP address Click the Edit Sender button if you want to edit the entered IP address Attention If you do not enter an address then every server has the permission to send a shutdown command You can define under Protocol if RCCMD should use SSL certificates Enable the Reject expired SSL certificates if you want to reject connections with expired certificates Please take a look into chapter 6 6 1 for further information about RCCMD with SSL 116 DOG Connections Mozilla Firefox File Edit View History Bookmarks Tools Help al vile A http localhost 8080 Options connections htm v d v Most Visitedv Getting Started Latest Headlines v Connections op GENERE 0 0 0 0 0 0 0 1 Connections v Options The list below identifies all senders that are allowed to connect to this listener Note An empty list means that every sender can connect to this listener Connections Heartbeats e Redundancy Shutdown Settings Notification Settings Advanced Settings RCCMD Insert Edit Sender Web Configuration Enter the Name or IP address of the incoming RCCMD Sender below Incoming RCCMD Sender 192 168 222 210 Ai Sender IP Address
52. that you selected for the CA The private key must not be encrypted to let the RCCMD Client service start without trouble Therefore we use the nodes option and the newreq command CA pl newreq nodes Sign with your CA CA pl sign Now create an empty filed named rccmd pem and copy the cert information of newcert pem rccmd certificate newkey pem private key and cacert pem CA into it Please note that the exact copying is required to use it without trouble Use your own RCCMD certificate Do the following steps at the RCCMD Client and every sender e g UPS Web Manager Backup the existing rccmd pem e Replace the existing rccmd pem with your own e Restart the RCCMD Client Restart the RCCMD Sender 3 8 Configuration of rccmd cfg file in a non grafical environment It is required to perform the configuration via editor if you do not have a graphical interface The configuration file is the rccmd cfg and is located into the usr rccmd folder default The file contains the description of the single configuration parameters Please take a look into the following example of the rccmd cfg file and change the settings to your installation HH EEE RCCMD Configuration 80 HH HEHEHE Bind on Interface Defines on which interface we listen for incoming commands Default 0 0 0 0 All possible interfaces on this host ListenAddress 0 0 0 0 Listen on Port Defines on whi
53. the Tab key until the Add button is highlighted then press Enter generex host usr ups Valid Sender Addresses Add Address Cancel Add Edit Delete Ok Cancel Figure 122 RCCMD UNIX Sender Example Enter the IP address of the host you want to be able to connect then press Enter 94 Fs generex host usr ups Valid Sender Addresses ISAGEN Add Edit Delete Ok Cancel Figure 123 RCCMD UNIX Sender Overview To edit an entry in the list select it by hitting the 1 and keys until the entry is highlighted then hit the Tab key until the Edit button is highlighted then press Enter generex host usr ups Valid Sender Addresses oe 168 101 Edit Address Cancel Add Delete Ok Cancel Figure 124 RCCMD UNIX Edit Sender Edit the Address in the Edit Address Window To keep your changes select the Ok button with the Tab key and press Enter otherwise select Cancel To delete an entry in the list select it by hitting the f and keys until the entry is highlighted then hit the Tab key until the Delete button is highlighted then press Enter 95 generex host usr ups Valid Sender Addresses 192 168 1 1 abe Fe so ea les Delete Address Selected Address 192 168 1 M ccc ccc ccc cece eee ccccceees Cancel Add Edit Ok Cancel Figure 125 RCCMD UNIX Delete Sender Confirm to
54. the key with the RX3 in the first part of the license key Most of the times you need to order the key separately Enter your license key ROCMD Software Clent No 12 45679910 123456789 10 RCCMD Client License Key carne hey LiexePXI12 34S 789 Usually the license key is located on the installation booklet or on a label on the rear side of the CD sleeve Figure 171 RCCMD Enter Your License Key Select the features you want to install 131 Install Set Typical 008 M RCCMD MV weblf Description This installs a webserver and a webinterface which is needed to configure RCCMD Figure 172 RCCMD Choose Install Set Choose an alias folder Where would you like to create aliases In the Dock On the Desktop C In your home folder Other Choose inside Applications on the disk Macintosh HD Don t create aliases Figure 173 RCCMD Choose Alias Folder Select the additional output options 132 By default rccmd will print the messages it receives from the network to dev console Here you can choose additional output options wo Display Messages on all terminals TA log messages Figure 174 RCCMD Messages It continues the pre installation summary Please Review the Following Before Continuing Product Name RCCMD Install Folder recmd in the folder usr on the disk Macintosh HD Alias Folder Applications on t
55. the rccmd sender in order to enable a connection It is normally not necessary to change this setting Enable UDP If this opion is enabled rccmd will open an UDP Listen Socket in addition to the TCP Socket This allows the rccmd listener to receive rccmd broadcasts Possible values are true and false The default is true To switch the value use the 1 and keys Timeout Timeout for TCP connections The default is 10 seconds It is normally not necessary to change this setting To reset all values to their defaults select the Default button by hitting the Tab key then press Enter To leave the screen select either Ok or Cancel with the Tab key and press Enter Ok means accept all values as displayed on the screen Cancel means discard all changes made to the screen Configure Access Control List Access Control List contains a list of valid sender addresses A valid sender address is the IP address of an rccmd sender that is allowed to connect to the rccmd listener Initially the list is empty D Note An empty Access Control List means everyone is allowed to connect To switch between the entries in the list use the 1 and keys to switch between the buttons use the Tab key To select an entry press Enter 93 ME generex host usr ups Valid Sender Addresses Add Edit Delete Ok Cancel Figure 121 RCCMD UNIX Add Sender To add an IP address hit
56. want to change something on a previous screen click the Previous button You may cancel this installation at anytime by clicking the Cancel button Installer version 574 Figure 70 Installation Introduction Enter your license key REEMD GClient Enter your license key RCCMD Client License Key 739 b 3 my L2ereRK3123435799 Enter license key I 4 Usually the license key is located on the installation booklet or on label on the reverse side of the CD sleeve Figure 71 Installation License Key Choose the desired features 56 REGMD Glient WIRCCMD v Weblf WIXMessage ET gt Description This installs the application feature Cancel Previous Next Figure 72 Installation Choose Install Set Choose your desired installation path REEMD Client Please choose a destination folder for this installation Where Would You Like to Install usr rccmd Restore Default Folder Cancel Previous Figure 73 Installation Choose Install Folder Please note the required firewall exceptions 57 een paean Required Firewall Exceptions Make sure following Ports are not blocked by any firewall Ports 8443 amp 8080 tcp Weblf Server if installed Ports 6003 amp 5769 tcp udp RCCMD Figure 74 Installation Firewall Exceptions Choose the additinal output options REEMD Client By default rccmd will print the messages it receives from th
57. 27 0 0 1 v Status Event Log e View Event Log These are the events that have occured on this computer System Status no log data yet Em Figure 19 RCCMD W eblinterface Certificate Error D Attention Use the access data User admin Password cs121 snmp 19 Click the Ok button because the rccmd log file is empty of course because RCCMD was not started yet Click the Options button to start the configuration You can enter the IP addresses of the allowed RCCMD senders CS121 UPSMAN into the Connections menu Click the Insert Sender button to enter the IP address of the 1 ender Click the Remove Sender button if you want to remove the already entered IP address Click the Edit Sender button if you want to edit the entered IP address DQ Attention If you do not enter an address then every server has the permission to send a shutdown command You can define under Protocol if RCCMD should use SSL certificates Enable the Reject expired SSL certificates if you want to reject connections with expired certificates Please take a look into chapter 3 9 for further information about RCCMD with SSL gt gt http localhost 8080 Options c Datei Bearbeiten Ansicht Favoriten Extras We Favoriten 983 Web Slice Katalog v Connections v Options The list below identifies all senders that are allowed to connect to this listener Note
58. 34 rccmd Properties Local Computer Recovery Dependencies 2 al Allow service to interact with desktop fe Undocked Profile Enabled Docked Profile Enabled Figure 43 RCCMD Properties Password Confirmation Select User Figure 44 Select User Window Click the examples button to select the object name 35 Select User H E Select this object type User ar Built in security principal Object Types From this location 6X72 Locations Common Queries Mame Starts with gt Bolumen Description Starts with Disabled accounts Stop I Hon expiring password Days since last logon vj OF Cancel Name ROH In Folder vmware Ut GA Administrator GX72 f ASPNET r frank f Guest f Help ssistant E IUSR GX72 E wah G72 P LOCAL SERV ET NETWORK 5 SUPPORT 3 GX72 Figure 45 Selection of the Object Name Select User F Select this object type User or Built in security principal Object Types From this location x72 Locations Enter the object name to select examplez Check Names Gr7 2 dministrator Figure 46 Administrator Selection DE Cancel ee Click the Ok button and enter the new password twice 36 rccmd Properties Local Computer Fi General Log On Recover Dependencies Log on as C Local System account IV Allow service to interact with deskt
59. 5 104200553 Load recmd snim 1 a 192 10 200 52 If you have added a search path i e search add sysirocmd otherwise you have to use the absolute path load Sysireondircond nlm 1 To start RCCMD in receiving mode listen enter the following line load lt path gt RCCMD I a 192 200 100 10 p 6003 load lt path gt shutcmd nim f Optional parameters a lt address gt TCP IP address of the master computer s which sends the RCCMD signal p lt port gt optional TCP Port address on which the master computer is sending To start RCCMD in sending mode send enter the following line in your shutdown job load RCCMD s a lt address gt p 6003 For lt address gt enter the TCP address of the machine to which you want to send the RCCMD signal Workstations in listening mode with an active RCCMD with parameter l Optional parameters p lt port gt TCP Port which the RCCMD signal is using The option a can be used multiple times if a shutdown on remote network servers should be initiated Example Example path lt path gt sys ups upsman rccmd nIm load lt path gt RCCMD NLM s a 192 168 210 3 a 192 168 210 4 a 192 168 210 10 etc until end of line unload RCCMD load lt path gt RCCMD NLM s a 192 168 210 8 etc unload RCCMD Do not use the CD License key more than once If more RCCMD modules need to be installed for the shutdown additional CD license keys must be purchased Additi
60. 69 DOG Heartbeats Mozilla Firefox Tools Help File Edit View History Bookmarks Ko vi le A http ocalhost 8080 Options heartbeats htm v 9 7 Google N Most Visitedv 6 Getting Started Latest Headlines v 6 Heartbeats do v GENEREX 0 0 0 0 0 0 0 1 RCCMD UPS alive check teen CS121 UPSMAN addresses Alive result Ok v Options The UPS alive check can be used to monitor the availabilit Connections bl Enable automatic UPS alive check by the use of CS121 UPSMAN Traps Shutdown Settings An mn amp by polling CS121 UPSMAN every 1800 seco Advanced Settings and retry each failed connection 5 times Web Configuration When the alive check fails then RCCMD will use the follo Run this command file Jusr rccmd rccmd_notalive sh Test UPS connections s Run alive check now Figure 90 RCCMD Weblnterface Heartbeats You can test the UPS connection if you click the Run alive check now button the port 5769 will be tested Click the Save Changes button prior of the leaving of this site to save your changes You can enable the redundancy management feature into the menu Redundancy The redundancy level defines the number of redundant senders in the redundancy group This means that level 1 senders must have sent a shutdown signal before this RCCMD starts its shutdown sequence When redundancy suppresses a shutdown then RCCMD w
61. 7 PORT 6003 SSL Enable SSL PARAMET Additional Parameters can be entered here Do immediately once Do after 0 Seconds Do Always C Doafter 0 Seconds repeat C DoEvery 0 Seconds Do at 0 Minutes remaining Cancel Figure 35 UPSMAN Configuration WAKEUP Command Click into the UPSMAN configuration the buttons Advanced Users Events Power restored and Insert Add the function Send RCCMD execute to remote client set the accordant IP address of the RCCMD client and enter the command WAKEUP HA A pm pp pp r Ma En or oe hm NNNNNNDMN rr TY er r Figure 36 WAKEUP Command into RCCMD Log File D Advice The restart of the RCCMD service is a third opportunity to reset the redundancy alarm 2 6 RCCMD with SSL for Windows The Secure Sockets Layer SSL protocol is a cryptographic protocol that provides security and data integrity for communications over TCP IP networks 30 Use your Web browser to navigate to the address of your UPS Web Manager Click the Network amp Security configuration button and enable the SSL network feature Network amp Security Settings MAC Address 00 03 05 0E 09 E1 Enable Telnet Server Network Card Speed AUTO v Enable HTTP Server Local Address 192 168 202 98 HTTP Port 80 Gateway Address 192 168 202 1 HTTP Refresh Time 10 Subnet Mask 255 255 255 0 HTTP Default Page UPS Status DN
62. 91 hostshutdownactive true ups vm name vMA5 1 Key secret Language english vMotion true vCenterAddress 192 168 200 65 vMotionTimeout 92 5 RCCMD on Citrix XEN Server The RCCMD Software for Citrix XEN Server is a Linux based TCP client for receiving shutdown calls from UPSMAN software any vendor CS121 any vendor or other RCCMD licensed applications like SNMP adapters etc from other vendors RCCMD for XEN Server runs on GNU Linux 2 6 18 or higher which is the basis of the 2008 XEN Serverplatform 128 For installing RCCMD please refer to the user manual of RCCMD for UNIX chapter 5 3 page 61 following we describe some special aspects which are only applicable to XEN Server Installation Since the XEN Server does not offer any graphical interface the download of RCCMD client for XEN Server from the GENEREX Website or other sites is not easy unless you have extra tools installed like commandline browsers like Wget Additionally by default there is no FTP server active on XEN Server so a transfer of a downloaded RCCMD package is also blocked For this reason we recommend to use a local interface on your XEN Server like CD ROM Driver or USB stick Download RCCMD for XEN Server from the GENEREX Website using your original RCCMD licensekey not older than 2 years and extract the TAR file Copy the files on a CD R and insert this CD now into your XEN Server CD drive Alternativly use UPSMAN CD ROM Version 5
63. Advanced Settings The information below defines IP address and TCP port of the RCCMD Listener Web Configuration IP address 0 0 0 0 means all addresses 0 0 0 0 16003 Note IP address 0 0 0 0 means every local address default TCP Port is 6003 v Done Figure 94 RCCMD Weblnterface Advanced Settings Click the Save Changes button prior of the leaving of this site to save your changes You can change the default password for the user admin into the menu Web Configuration In addition you can disable the HTTPS protocol if you just want to use the HTTP protocol The RCCMD version 4 2 3 0 or higher provides the feature of changing the default ports for HTTP and HTTPS DOG Advanced Settings Mozilla Firefox s 100ls Help lt v A http localhost 8080 Options weblfManagement htm v bi v Goo EN Most Visited 6 Getting Started latest Headlines v 6 Advanced Settings an v GENERE x lt v Options The information below is used to log on to this user interface Administrator User Name admin Connections Current Administrator Password Heartbeats New Administrator Password Redundancy Select the access protocol for this user interface Shutdown Settings Protocol Advanced Settings Note Changes in protocol will become active upon the next start up Web Configuration Port for http 8080 Port for https 8443 Done F
64. An empty list means that every sender can connect to this listener Connections Heartbeats Sender IP Address Insert Sender Redundancy Shutdown Settings Notification Settings Advanced Settings Web Confiquration RCCMD Insert Edit Sender Enter the Name or IP address of the incoming RCCMD Sender below Incoming RCCMD Sender 192 168 222 243 Protocol The setting below increases the security of connections to this RCCMD Accept only SSL connections requires restarting RCCMD Reject expired SSL certificates Save Changes Figure 20 RCCMD Weblnterface Configurator Connections Click the Save Changes button prior of the leaving of this site to save your changes You can enable the UPSMAN Alive Check feature into the menu Heartbeats This check is a signal that will be send to the CS121 UPSMAN via port 5769 if the UPSMAN service still got UPS data If not the script file alive bat will be executed which will trigger an accordant pop up message The feature by the use of CS121 UPSMAN Traps provides UPSMAN RCCMD UNMS messages which will display the UPS status as message If enabled this feature will trigger a message if the UPS status of the UPSMAN RCCMD servers has changed 20 The feature by polling CS121 UPSMAN every x seconds provides the pure signal polling without receiving UPS data or rather messages The polling rate defa
65. CCMD Shutdown Sequence rrrnnnnvnvvvnnvvvvvvvrvvrnrrnrrnrnnnrnnnnnn 86 Figure 113 Configuration RCCMD E Mail Configuration vvvvvvvvvvvvvvvvrvvrvrrrvrrrvrrnrvnnnner 87 Figure 114 Configuration RCCMD Control rrnnnnnnnrvvvnvnerrnnnnnnnnnnnnnnnnnrrrvnnnnerrrnnnnnnnnnnnnnnnn 88 Figure 115 ROCMD Shutdown Sh sesso sed ec eas sae ck ced dc Saas 89 Figure 116 ROCMD Shutdown SeqQuence cccccccccccccceeceeseeeeeeeaeeeeeeaeeesaaaasaaaaaaaaaaaaaaaaaes 89 Figure 117 RCCMD Shutdown Relay cccccccccccseesssssssensseeeeeeeeeeeeessessesseaeeeeeeeeeeeseesssssaas 90 Figure 118 Making the Configuration File rrrrrrrrrrrrrrrrrrrrrrrvvrnvrvrvrrvrrrrrrrrrrrrnnrrrsnnrnnnnnnnnen 91 Figure 119 RCCMD Configuration Menu UNIX cccsscsccccceceeeeeeeeeeeeeesseeeeeeeeeeeeeeseseeesaas 91 Figure 120 RCCMD UNIX Network Options ccccccccceccececeeeeseeseeeeeeeeeeeaeeaeaaeaeeaaaaeaaaaaaeas 92 Figure 121 RCCMD UNIX Add Sender cece cecceessseeeceeeeeeeeeeeeeesseseesnaeeeeeeeeeeeesessseeaas 94 Figure 122 RCCMD UNIX Sender Example ccccccccccccceceeeeseeeeeseeeeeeeeeeeeaeeaaeaaaaaeaeaaaaaas 94 Figure 123 RCCMD UNIX Sender Overview cccsssccccceeeeeeeeeeeeesesseseneeeeeeeeeeeeesesseseaas 95 Figure 124 RCGMD UNDX Edit Sender ynyr a NN 95 168 Figure 125 RCCMD UNIX Delete Sender cccccccccccccccceeceeeeeeeeeeaeeeaeaaaaaeaaaaaaaaaaaaaaaaaaaas 96 Figure126 ACCMBD UNIX Send
66. CCMD and wait for the RCCMD signal of the UPS server If a power failure forces the master computer to shutdown the server network the shutdown job of the UPS server will start RCCMD RCCMD now sends the RCCMD signal to all computers in its list The computers receive this signal and the installed RCCMD will execute the programmed command Please note that it is required to install RCCMD in two different operating ways 1 as a sending process on the UPS server RCCMD s send 2 as a receiving process background process on the receiving computers RCCMD 1 listen In contrast to the RSH RCCMD does not include the command that is to be executed in the sending process but instead deposits the command with the receiving process This provides a security advantage in comparison to the RSH Furthermore the receiving process may check which computer sends the RCCMD signal and determines whether to accept it or not Attention If a name resolution is achieved via DNS please always use the IP address and not the computer name for a network shutdown with RCCMD In case the DNS is not available the network shutdown will not work if this method is not used RCCMD Version 2 or higher The extended Version of RCCMD is also able to execute commands on remote computers execute the shutdown batch in the same TCP IP port 6003 execute an e mail batch enable log file entries etc The RCCMD 2 sender UPSMAN or CS121 SNMP adapter sends the
67. CMD shut down relay to 111 111 111 1 RCCMD shut down relay to 111 111 111 1 o l Wait 5 seconds usr recmd rcemd message sh Parameter Shut down System gt gt A Add custom application Description of Shut down System Ends your session and shuts down System 50 that you can safely turn off computer Save Cancel Figure 112 Configuration RCCMD Shutdown Sequence The following commands are available 86 RCCMD shutdown relay Relays RCCMD shutdown command to another workstation Enter the IP address or the hostname of the remote station you want to shutdown see chapter 4 4 page 73 Wait seconds Waits a duration in seconds until the next command will be executed Restart System Ends your session shuts down the system and restarts it Shutdown System Ends your session and shuts down the system so that you can safely turn off the power Click the Configure button to enter the E Mail settings RCCMD Configuration mera Addresses Functions Logfile Execute Control Execute at mail signal from RCCMD server ng Jusr rcemd roomd mail sh T 93 Edit File JRCCMD Configure Mail E Mail Confiquration Tosa Use E Mail E Mail address of the sender Mame of the mail server m ka SMTP Authentification Ll Use SMTP Authentification E Login Password T Figure 113 Configuration RCCMD E Mail Configuration ROOM Click Control to get to the f
68. CS121 Additionally all Web browser event configurations have a certain limitation so that it is required to use the relay function if the number of jobs exceed 50 per event at the CS121 HW 131 at older CS121 adapters even earlier See the following script which lets the RCCMD client act as relay station Figure 33 Example Batch File RCCMD act as Relay Station 28 start is a Windows batch command to start the program call in several instances This allows to execute programs simoultanously and speeds up the shutdown process Please note that start is not supported in all Windows versions and it should be tested before using 2 5 Automatic Reset of the Redundancy Alarm You can use the function Send RCCMD cancel shutdown to discard a previously sent shutdown automatically If a shutdown was suppressed because of the existing redundancy at this point of time but the problem was solved at the UPS intermediate you can reset the shutdown with the function Send RCCMD cancel shutdown The client which received the shutdown will be encouraged to reset it This command can be set individually into your CS121 UPSMAN or BACS WEBMANAGER Events Alarms configuration but makes sense only if the event which will send the command is true if the UPS is back in normal condition For this the events POWER RESTORED BATTERY LOW OFF UPSMAN STARTED and GENERAL ALARM OFF are suitable if they are provided
69. D MASTERKEYCODE testing purpose only do not use for customer installations 2012 10 18 15 23 22 rccmd 03915 V4 2 3 0 Unix Remote Command Program 2012 10 18 15 23 23 rccmd 03923 Listen Mode started 2012 10 18 15 23 23 rccmd 03923 RcvThreadUdp started Done Figure 166 RCCMD Weblnterface Event Log 125 You can check the current status of RCCMD into the menu Status System Status update the status and restart or rather stop start the RCCMD service DOG System Status Mozilla Firefox File Edit View History Bookmarks Tools Help lt lt v A http localhost 8080 Status systemStatus htm v 8 Gooo oN Most Visited 6 Getting Started latest Headlines v 6 System Status oP v 0 0 0 0 0 0 0 1 v Status System Status View Event Log Current status of RCCMD is running System Status Update Status Restart RCCMD Start RCCMD Stop RCCMD Done Figure 167 RCCMD Weblnterface System Status You can open the RCCMD user manual into the menu Help ad you can follow the link to www generex de 5 E Manuals Mozilla Firefox ed X E A amp httplocalhost 8080 Helpimanuals htm v 4 v A B Most Visited 8 Getting Started Latest Headlines v Manuals Nane Figure 168 RCCMD Weblnterface Help DQ Attention Please note that it is required to start the vMA manually after a shutdown 126 4 2 5 Alternative Configuration vi
70. Figure 195 RCCMD Configuration Window Logfile ccecceeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 146 Figure 196 RCCMD ConfigurationW indow ExeCute rrrrrrrrrrrnnvrnrrrvrererrrrrrrrrrrrrrrrrrrnnnnnn 146 Figure 197 RCCMD E Mail Contiguration ccccccccccccccccccccsenseeeeeeseeeeeeeeeeeeeaaeaeeeaeaaaneaes 147 Figure 198 Configuration RCCMD Execute ccccccssscceceeeeeeeeeeeeeessessssnaeseeeeeeeeeeeeess 147 Figure 199 Configuration RCCMD Shutdown Sequence rrrrrrnnrnrrrnnnnnnrrrrnnnnnnnrnrnrrrrrnnn 148 Figure 200 RGCOMD Cour E A 149 Figure 201 Error after execution of upsVIShutdown pl usvrrrrrrrrrrrrrrrrrrrrvvvvvvrvvvvrrvvvnnenn 156 Figure 202 Listing of the IP tables see the ACCEPT at the TCP and UDP ports 6003 TOP DONO seede asset ag 158 Te 2 UMN Ravers renee Remar Rate ete are nee RoC ame Aree aire Ae ROetTR nner nn oT oe ERR Reo 162 Figure 205 CS121 Configuration for such a relay command cceeeeeeeeeeteteeeeeeeeeeeeees 163 Figure 206 Raritan Device Settings ccccccccecesssenneeeceeeseenneeeeeesseeeneeeeeeesseecsneeeeeeesssseneees 164 Figure 207 Raritan SNMP Settings sesi a a ae 164 171
71. N has still UPS data or not If this fails the scriptfile alive bat will be executed which causes a messagbox coming up The polling rate default 30 min defines the polling of the UPSMAN service connect retries default 5 means after 5 unsuccessful connection tries an alarm will be triggered If you click the Test connection s button the UPSMAN alive checking of the entered IP addresses will start port 5769 will be tested 144 AOO RCCMD Configuration I Addresses Functions Logfile Execute Control L Nr UPSMAN address Alive Result fion s 192 168 222 2 Successfully connected to UPSMAN IRCCMDCFG V4 0 0 Figure 193 RCCMD Check UPSMAN Connections If you click the Browse button you will get a selection of the default batch files If you click the Default setting button you will get back to the default batchfile alive bat At the failure of the UPSMAN alive checking you can define an executing file or edit the default file alive bat Addresses Functions Logfile Execute Control UPSMAN alive checking wi Enable connection check Test connection s Polling rate 30 min E Connection retries 5 Execute at failure UPSMAH fusr rcemd recmd_execute sh Default Set Edit File RCCMD Redundancy O Use RCCMD group redundancy IECCMDEOFG V4 0 0 11 TD Figure 194 RCCMD Redundancy At UPS installation RCCMD offers a redu
72. Name someone Account Password eee Figure 61 RCCMD Email Settings Enter the accordant parameter and click the OK button Use the following RCCMD command Mail receiver address text 192 168 222 210 System amp Network Status Device Status Device Status Graphic Device Functions AUX Status UPS Model amp System Network amp Security Device Status UPS STATUS OK AUX Status Job Editor Powerfail Job 3 Function Send RCCMD Command to remote client v When amp Client IP or Hostname 192 168 200 17 Client Port Default 6003 6003 Command mail someone somewhere com text S4 Command Cancel RCCMD Shutdown PA Figure 62 CS121 Email Command Step 9 49 If you want to change the shutdown sequence click the Configure button File C Program FilesYRCCMD shutdown bat Available Commands Current Sequence Log off user Shut down Windows Power off Windows Restart Windows Hibernate Windows Suspend Windows Quit Lotus Notes at EE Quit Siemens SIMATIC m Quit Applications v 4 ul Description of Add custom application Log off user Ends your session leaving the computer running on full power Cancel OK SZ Execute at shutdown signal from RCCMD server C Program Files RCCMD shutdown bat Browse Ed
73. S Server 192 168 202 8 Enable HTTP Tooltips 7 Enable UpsMon Server v Use RCCMD2 Traps v Confirm Password Enable RCCMD Listener F Change Administrator Password RCCMD Listener Port Change UpsMon amp SS4 Password RCCMD Timeout Use RCCMD SSL Confirm Password Use UpsMon Password for Web Pages Figure 37 RCCMD SSL Settings The SSL network feature requires correct time settings so it is required to configure a timeserver Click the Timeserver configuration button and enter the address of at least one timeserver Time Settings RFC868 TCP compatible timeserver listening on port 37 required To disable the timeserver feature set timeserver address 1 to 0 0 0 0 Some public timeservers could be used for both protocols 129 6 15 29 National Institute of Standards and Technology 192 53 103 103 Physikalisch Technische Bundesanstalt Current system time Thu Dec 4 23 49 26 2008 imeserver Address 1 192 53 103 103 SNTP v Timeserver Address 2 0 0 0 0 SNTP v Timeserver Address 3 0 0 0 0 SNTP v Timezone GMT 01 00 Amsterdam Berlin Bern Rome Stockholm Vienna v Automatically adjust clock for daylight r e changes implemented for european timezones only Connection Retries 2 Synchronize Time on nan incoming RAS connection Synchronize Time on outgoing RAS connection Test Timeserver 1 Test Timeserver 2 Test Timeserver 3 Synchronize CS121 cl
74. Tray In next menu you can choose to create a new program group default or to choose icons elsewhere or not at all Tei Choose Shortcut Folder Introduction Where would you like to create product icons License Agreement In a new Program Group Rccmo Choose Install Folder Choose Shortcut Folder In an existing Program Group fRccMD z Pre Installation Surrirriar Inthe Start Menu Installing l l On the Desktop Install Cormplete Inthe Quick Launch Bar Other Choose Dont create icons W Create Icons for All Users InstallAnywhere by Macrovision Cancel Previous Net Figure 9 Shortcut Folder Selection In the next menu you see an overview of your installation and you may now press Install to begin 11 Shortcut Folder Pre Installation Summary Install Corplete Shortcut Folder CADokumente und Finstellungen erik Startmeni Programme RCCMD Disk Space Information for Installation Target Required 93 332 734 bytes Available 112 805 849 088 bytes InstallAnywhere by Macrovision Figure 10 Summary Select these default values for port and protocol for RCCMD Weblf or select new ones The default port appears to be free Select these default values for Port and Protocol for RCCMD Webif or choose new ones Access Protocol RCCMD Weblf Port Default 8080 8080 Figure 11 Set Weblf Access RCCMD has been installed successful 12
75. UTS Do Not Install USER SHORTCUTS C WDokumente und Einstellungen lt W indows User gt Startmenu Programme UPS Choose Feature List If you want to install a subset of features from this installer make a list of all the features you want to be installed The List must be entered in the CHOSEN_INSTALL_FEATURE_LIST variable Options for the list are RCCMD Weblf CHOSEN_INSTALL_FEATURE_LIST RCCMD Weblf Choose OEM Enter your OEM number here OEM 0 Choose locatization If you want to install a different language than English you will want to provide the valid country code here This is only important for silent installations Valid codes are zh_cn de en fr el it ja ko pt ru es tr INST_LANG de Choose License Key 14 For silent installation your License Key must be provided here GXLICENSEKEY yournumber Choose Installer User Interface For installation in console modus pass the parameter i console to the installer If you want to use the installer in silent mode with no user interaction you can set this variable to silent Default is gui INSTALLER Ul silent INSTALLER_Ul gui Weblf Settings Here you can override default settings for access to the RCCMD Weblf Hit These settings are ignored if the variable CHOSEN INSTALL FEATURE LIST is set and does not contain the Weblf feature In interactive
76. Version 2014 08 07 RCCMD Multiple Server Shutdown Software User manual Version 2014 08 07 Copyright Statement for Intellectual Property and Confidential Information The information contained in this manual is non conditional and may be changed without due notice Although Generex has attempted to provide accurate information within this document Generex assumes no responsibility for the accuracy of this information Generex shall not be liable for any indirect special consequential or accidental damage including without limitations lost profits or revenues costs of replacement goods loss or damage to data arising out of the use of this document Generex the manufacturer of the BACS products undertakes no obligations with this information The products that are described in this brochure are given on the sole basis of information to its channel partners for them to have a better understanding of the Generex products Generex allows its channel partners to transfer information contained in this document to third persons either staff within their own Company or their own customers either electronically or mechanically or by photocopies or similar means Generex states that the content must not be altered or adapted in any way without written permission from Generex It is agreed that all rights title and interest in the Generex s trademarks or trade names whether or not registered or goodwill from time to time of Gene
77. a Editor You can edit the rccmd cfg file default usr rccmd as follows HH RCCMD Configuration v3 default HH Bind on Interface Defines on which interface we listen for incoming commands Default 0 0 0 0 All possible interfaces on this host ListenAddress 0 0 0 0 Listen on Port Defines on which interface port we listen for incoming commands Default 6003 ListenPort 6003 Enable UDP Defines if we should listen for rccmd UDP broadcasts Default true ListenUDP true Access Control List A list of valid sender addresses only its members can connect to us Seperate IP addresses with a space e g 192 168 0 1 192 168 0 2 Default lt empty gt Everyone is allowed to connect to us AllowedAddresses HH Alive Check Enable Alive Check Defines if we should perform UPSMan alive checking Default false AliveEnabled false Alive Check Rate Defines the interval of UPSMan alive checking in seconds Default 1800 Alivelnterval 1800 Alive Retry Rate Defines the number of UPSMan alive checking retries in case of problems Default 0 AliveRetries 5 Alive Check Group Members List A list of UPS device addresses that should be checked periodically Seperate IP addresses with a space e g 192 168 0 1 192 168 0 2 Default lt empty gt No alive checking AliveAddresses Alive Program Full path to script that is
78. aa ole GS meccarce Fa pa opa pm oe cs ce ce H AA AAKA ar ea Figure 102 WAKEUP Command into RCCMD Log File 3 7 RCCMD with SSL for UNIX The Secure Sockets Layer SSL protocol is a cryptographic protocol that provides security and data integrity for communications over TCP IP networks Use your Web browser to navigate to the address of your UPS Web Manager Click the Network amp Security configuration button and enable the SSL network feature 11 Network amp Security Settings MAC Address 00 03 05 0E 09 E1 Enable Telnet Server Network Card Speed AUTO Enable HTTP Server Local Address 192 168 202 98 HTTP Port Gateway Address 192 168 202 1 HTTP Refresh Time Subnet Mask 255 255 255 0 HTTP Default Page DNS Server 192 168 202 8 Enable HTTP Tooltips Enable UpsMon Server Use RCCMD2 Traps Confirm Password Enable RCCMD Listener Change Administrator Password RCCMD Listener Port RCCMD Timeout Use RCCMD SSL Change UpsMon amp SS4 Password Confirm Password Use UpsMon Password for Web Pages Figure 103 RCCMD SSL Settings The SSL network feature requires correct time settings so it is required to configure a timeserver Click the Timeserver configuration button and enter the address of at least one timeserver Time Settings RFC868 TCP compatible timeserver listening on port 37 required To disable the timeserver feature set time
79. achines on each host The order in which the virtual machines are shut down is not configurable The selection of Virtual Machines Behaviour Put Host s into Maintenance Mode can attempt to send a host into maintenance mode thereby triggering vMotion for the virtual machines Select this option only if DRS Distributed Resources Scheduler is configured to be in fully automated mode and vMotion has been successfully tested for every virtual machine If maintenance mode fails then the remaing hosts will proceed with the Shutdown Virtual Machines Behaviour To calculate how much backup time remain when initiating this RCCMD command the values for the longest Shutdown Duration of the hosts and maintenance mode timeout must be added Enter the period of time after which to abort trying to reach Maintenance Mode If Maintenance Mode is not reached after this time then the remaining hosts will proceed 123 with the Shutdown Virtual Machines behaviour This is the last resort to shutdown the hosts and virtual machines gracefully Click the Save Changes button prior of the leaving of this site to save your changes and restart RCCMD You can define the maximum size of the event logfile into the menu Advanced Settings where the overwriting of older entries will start the RCCMD bindings for the IP address the RCCMD listener TCP port and the RCCMD Tray Message Port which will be used for the RCCMD messages In additi
80. adlines v 6 System Status op a 0 0 0 0 0 0 0 1 v Status System Status View Event Log Current status of RCCMD is running Status Restat RCCMD Stat RCCMD Stop RCCMD Done Figure 97 RCCMD Weblnterface System Status 74 You can open the RCCMD user manual into the menu Help ad you can follow the link to www generex de E E Manuals Mozilla Firefox i i http tocainost s080 Helpimanuals ntm v tay a fig Most Visited 6 Getting Started jjLatest Headlines v 3 Manuals qr 0 0 0 0 0 0 0 1 Find more documemation online here Nane Figure 98 RCCMD Weblnterface Help 3 5 RCCMD Remote Access RCCMD provides its own web interface from version 4 0 1 9 or higher Therefore it is possible to configure and control RCCMD remotely Please note that the firewall port 8080 TCP is enabled Enter the following into a web browser to connect to a workstation where RCCMD is running http IP address of the RCCMD client 8080 Status Event Log View Event Log These are the events that have occured on this computer System Status Authentifizierung erforderlich Q http 192 168 200 17 8080 verlangt einen Benutzernamen und ein Passwort Ausgabe der Website RCCMD Config Benutzername Passwort Figure 99 RCCMD Weblnterface Configurator Remote Access 75 3 6 Automatic Reset of the Redundancy Alarm You can use the function Send
81. al machines when the system starts During shutdown they will be stopped in the opposite order Order Virtual Machine Startup Startup Delay Shutdown Shutdown Delay Automatic Startup TE 1 a vMA 5 0 0 1 Enabled 10 seconds Suspend 30seconds 2 El vSphereManagem Enabled 10 seconds Suspend 30seconds ove Do 3 EG vMA5 Enabled 10seconds Suspend 30seconds a E VMware vCenter S Enabled 10seconds Suspend 30seconds t Any Order Manual Startup Joe es Figure 137 vSphere Client Startup and Shutdown 108 Power Off Switch off without shutdown Guest Shutdown Shutdown of the OS only if the VMware tools are installed Suspend Hibernating or sleep mode the virtual machines will be stopped GP Attention The shutdown via the VMware tools do not assure that the shut downed guest systems will start without loosing data To avoid this risk you can use RCCMD on the virtual machines too The RCCMD shutdown will be executed prior of the shutdown of the physical host We recommend to use it if you are using data bases The further times of delay for the guest systems VMWares who should be shut down via the host can differ and should be arranged individually Therefore the duration of the shutdown will increase accordingly The shutdown function of the guest systems virtual machines will be transferred to the ESXi host Some virtual machines are addicted from each other so that it is required to shut
82. alue by overwriting the string in the options field or by selecting a file in the file browser To invoke the file browser hit the Tab key until the Browse button is highlighted then press Enter To reset all values to their defaults select the Default button by hitting the Tab key then press Enter 98 To leave the Screen select either Ok or Cancel with the Tab key and press Enter Ok means accept all values as displayed on the screen Cancel means discard all changes made to the screen and switch back to the previous state Configure Logfile Options The rccmd listener is able to write and maintain a logfile It will log events such as startup and shutdown of the program accepted and denied network connections and executed commands Some parameters may be configured on this screen generex host usr ups Enable logging to file Select maximum size of Logfile Options truel logfile kbytes 1024 Logfile name usr ups rccmd l0 sssssssssssssssssss Browse Default Figure 128 RCCMD UNIX Log File Options Enable logging to file Select maximum size of log file Log file name 99 Possible values are true and false true is the default To change the value use the 1 and keys The log file will not gain larger than this size If the size of the log file would exceed this limit rccmd will automatically shrink it by 10 before it continues wri
83. ame as the installer e g install RCCMD properties then the installer should automatically use this file To call the installer with a parameter providing a properties file the installer need the parameter f in this case the command line call looks somewhat like this install RCCMD exe f silent installer properties To set the installer User Interface without providing the variable in the properties file the parameter i can be used E g install RCCMD exe i silent The interface options are silent gui console the gui option is default Choose Feature List If you want to install a subset of features from this installer make a list of all the features you want to be installed The List must be entered in the CHOSEN_INSTALL_FEATURE_LIST variable Hit Options for the list are RCCMD Weblf XMessage CHOSEN INSTALL FEATURE LIST RCCMD W eblf XxMessage This will set the User Interface of the installer For installation in console modus pass the parameter i console to the installer HINSTALLER Ul silent This presets the Licensekey This value is necessary for a silent installation because there is no other way to pass this information to the installer GXLICENSEKEY 62 The Dialogbutton variable contains the answer to the pop up question whether the RCCMD should be started at system boot The value 0 default resembles the answer Yes
84. ation and configuration via executing of your Windows batch file InstallAndConfigRCCMD bat 2 2 Console Installation of the RCCMD Installation This console installation works interactive and will ask for user input defined in the installation script file installer properties See above D Note This concerns the installation only The configuration will be performed via editor into the rccmd cfg file For the activation of the console installation it is required to remove the hash mark prior of the variable INSTALLER UI and to enter console This is the interactive RCCMD installation onto the console Execute the installIRCCMD exe file 2 2 1 Example of a Console Installation Adjust the file installer properties accordingly like described above or execute the following command installRCCMD exe i console Select the desired language and note the introduction Deutsch ENGLISH FRENCH LOGALE BY NUMBER reated with InstallAnywhere gt InstallAnywhere will guide you through the installation of RCCMD Client It is strongly recommended that you quit all programs before continuing with this installation Respond to each prompt to proceed to the next step in the installation If you want to change something on a previous step type back You may cancel this installation at any time by typing quit Installer version 315 PRESS lt ENTER gt TO CONTINUE Figure 14 RCCMD Console I
85. ave Changes button prior of the leaving of this site to save your changes You can change or rather extend the shutdown sequence into the Shutdown Settings menu The shutdown bat will be executed by default rem created by setup echo off set path path C Program FilesiIRCCMD ExitWin exe shutdown force clis 71 gt X Shutdown Settings Mozilla Firefox wa e http Nocalhost 8080 Options shutdownsSettings htm a GR 2 fi Most Visited Getting Started Bjjlatest Headlines v Shutdown Settings pay v 0 0 0 0 0 0 0 1 Sno senings v Options When RCCMD shuts down your operating system it will use the following sequence Sonnesttons fp Commandseguenee Heartbeats Redundancy Shut down System Settings file Jusrirccmdirecmd_shutdown sh Figure 92 RCCMD Weblnterface Shutdown Settings You can change or rather extend the default bat files for E Mail Message and Execute if you click the Edit File button DOG Notification Settings Mozilla Firefox File Edit View History Bookmarks Tools Help lt a v A http localhost 8088 Options notificationSettings htm v v Goog Most Visitedv 6 Getting Started Latest Headlines v 6 Notification Settings op v 0 0 0 0 0 0 0 1 v Options When RCCMD receives an e mail signal it will use the following setting Run this command file Jusrirccmd rccmd_mail sh Advanced Settings M
86. ble too to configure the function Send RCCMD command to remote client with the W AKEUP command Power restored Job 3 Function Send ROCMD Command to remote client Client IP 192 168 200 17 Client Port Default 6003 5003 Command WAKEUP Figure 100 CS121 Configuration WWAKEUP Command Click into the CS121 menu Events Alarms onto Power restored and add a new job Select the function Send RCCMD command to remote client set the accordant IP address of the RCCMD client and enter the command WAKEUP 76 DER AL Ly Insert Function Function Send RCCMD EXECUTE to remote client Function Parameters Parameter ADDRESS 192 168 200 17 FORT 6003 SSL Enable SSL PARAMET Additional Parameters can be entered here Do immediately once C Do after 0 Seconds C Do Always t Do after 0 Seconds repeat Do Every E seconds Doat 0 Minutes remaining Cancel Figure 101 UPSMAN Configuration WWAKEUP Command Click into the UPSMAN configuration the buttons Advanced Users Events Power restored and Insert Add the function Send RCCMD execute to remote client set the accordant IP address of the RCCMD client and enter the command WAKEUP 20 0 ft ft fot fot fo fo ft ft mM hh hh Rh NM MN to a to to cow D a SS md a Y Y DY DYI DYI I Mo MG ee ee Cots bos oe G oe O oe ea H es A A RS L pt
87. cel shutdown The client which received the shutdown will be encouraged to reset it Please take a look into chapter 6 1 for further information about RCCMD with redundancy Click the Save Changes button prior of the leaving of this site to save your changes You can change or rather extend the shutdown sequence into the Shutdown Settings menu The shutdown bat will be executed by default rem created by setup echo off set path path C Program Files RCCMD ExitWin exe shutdown force clis 138 gt X Shutdown Settings Mozilla Firefox wa e http Nocalhost 8080 Options shutdownsSettings htm a GR 2 fi Most Visited Getting Started Bjjlatest Headlines v Shutdown Settings pay v 0 0 0 0 0 0 0 1 Sno senings v Options When RCCMD shuts down your operating system it will use the following sequence Sonnesttons fp Commandseguenee Heartbeats Redundancy Shut down System Settings file Jusrirccmdirecmd_shutdown sh Figure 183 RCCMD WeblInterface Shutdown Settings You can change or rather extend the default bat files for E Mail Message and Execute if you click the Edit File button DOG Notification Settings Mozilla Firefox File Edit View History Bookmarks Tools Help lt a v A http localhost 8088 Options notificationSettings htm v v Goog Most Visitedv 6 Getting Started Latest Headlines v 6 Notification Settings
88. ch interface port we listen for incoming commands Default 6003 ListenPort 6003 Enable UDP Defines if we should listen for recmd UDP broadcasts Default true ListenUDP true Access Control List A list of valid sender addresses only its members can connect to us Seperate IP addresses with a space e g 192 168 0 1 192 168 0 2 Default lt empty gt Everyone is allowed to connect to us AllowedAddresses Alive Check Enable Alive Check Defines if we should perform UPSMan alive checking Default false AliveEnabled false Alive Check Rate Defines the interval of UPSMan alive checking in seconds Default 1800 Alivelnterval 1800 Alive Retry Rate Defines the number of UPSMan alive checking retries in case of problems 81 Default 0 AliveRetries 5 Alive Check Group Members List A list of UPS device addresses that should be checked periodically Seperate IP addresses with a space e g 192 168 0 1 192 168 0 2 Default lt empty gt No alive checking AliveAddresses Alive Program Full path to script that is executed when an alive check fails Default rccmd notalive sh AliveProg Redundancy Mode Enable Redundancy Defines if we should operate in redundancy mode Requires an enabled lt Alive Check gt configuration Default false RedundancyEnabled false Redundancy Group Members List A list of redundancy group member addresses
89. corresponding RCCMD signal and the RCCMD 2 client starts the corresponding batch file which lead to the execution of the net send message The initial command will always come from the UPSMAN or CS121 where as the execution will always be on the RCCMD client side Example The CS121 should send a net send network message to a Windows NT network The CS121 can be programmed so that during the event Powerfail a RCCMD message will be send The text of the message is configurable by the user Upon on receiving the message by the RCCMD 2 client the client is starting a batch file and sends the net send message Sender of the message will be the client and initiator is the UPSMAN or CS121 This way it is possible to send messages e mail etc in the different networks and operating systems initiated by an UPS alarm Send Email Net send message Shutdown Shutdown Shutdown RCCMD 2 client RCCMD 2 client RCCMD 1 client NOVELL Server Windows Server e UPSMAN Server RCCMD 2 Sender Firewall Firewall CS 121 E PP gt gt gt UPSMAN Server OS 2 UNIX Server RCCMD 2 Sender RCCMD 1 client RCCMD 2 client Shutdown Shutdown Figure 1 RCCMD and UPSMAN in a network environment 2 Installation Configuration of RCCMD for Windows Note The RCCMD Installer is using our delivered Java Runtime Environment
90. d mnt cdrom by ls you can see the files on the CD change now to the folder DRIVERS PreviousVersions UNIX ALL UPSMAN CD ROM until you find the installationprogramm install Start now the installation by entering install and follow the instructions on the screen from here the installation is identical to any other RCCMD installation for UNIX After the installation is finished a new process will be running on your VMware ESX Server rccmd which means the system is ready now ATTENTION ESX Server has per default a firewall active which does not allow to send from remote RCCMD signals D Attention The VMware ESX server got an active firewall by default which denies the RCCMD signals Firewall Configuration The following firewall configuration of the VMware ESX Server is required to receive RCCMD signals esxcfg firewall o 6003 tcp in RCCMD Restart the firewall service to apply your settings service firewall restart RCCMD is now listening client mode and will start the file shutdown sh on your VMware ESX Server when any CS121 or UPSMAN transmit a RCCMD shutdown call This file shutdown sh makes an init0 shutdown on your VMware ESX Server edit this file if you want to use a different shutdown procedure Advice We recommend to install RCCMD on the virtual guest systems 104 too and to shut them down PRIOR of the shutdown of the physical host Therefore
91. down for shutdown enabled 10 seconds 30 seconds through vSphere Client IV Continue immediately if the VMware Tools start Shutdown Action configuration Startup Order Power on the specified virtual machines when the system starts During shutdown they will be stopped in the opposite order VM vMA Automatic Startup Startup Startup Delay Shutdown Shutdown Delay 1 Enabled 10 seconds Shut do 30 seconds A VMWare tool for Any Order Move Down configuration of ESXi Manual Startup g er J Hosts VM Windows CS121 Shutdown Prority 1st All VMs with RCCMD running eg Windows VMs Linux VMs 2nd vMA with RCCMD to shutdown this ESXi Host UPS Shutdown Figure 133 A RCCMD shutdown will be send to the optional RCCMD clients on the virtual machines than to the ESXi host 106 The vSphere client provides the possibility that every host can be configured that the virtual machines will be shutdowned prior of the shutdown of the physical host To use this function it is required to install the VMware tools on the virtual machines 4 2 2 Shutdown configuration of virtual machines on the ESXi host Select into the vSphere Client your host 1 click at configuration 2 and tag VMware starting shutdown 3 Now cklick the vMA button 4 and then Properties 5 Fie Edt View Inventory Administration Plugins Help E Q Home bag Inventory gt BB Inventory de 192 168 200
92. e network to dev console Here you can choose additional output options Display Messages on all terminals log messages Display Messages with Xmessage Figure 75 Installation RCCMD Messages In the next menu you see an overview of your installation and you may now press Install to begin 58 REEMD Glient Please Review the Following Before Continuing Product Name RCCMD Install Folder usr reemd Product Features RCCMD Message Weblf Disk Space Information for Installation Target Required 121 345 686 Bytes Available 14 093 357 056 Bytes Figure 76 Installation Pre Installation Summary Choose the RCCMD start behavior RCCMD Client Pc Run REGMD at System Boot Automatically start RCCMD at System boot Should the RCCMD be automatically started when the System boots Cancel Figure 77 Installation RCCMD Start Behaviour Select these default values for the RCCMD Weblf port and protocol or select new ones 59 RCCMD Client The default port appears to be free Select these default values for Port and Protocol for RCCMD Weblf or choose new ones Access Protocol Default p RCCMD Weblf Port Default 8080 80800 Figure 78 Installation Set Weblf Port Please note this advice REEMD Glient It is necessaryto configure RCCMD Please use the web interface at http lt address of this computer gt 8080 Should you decide to run RCCMD with th
93. e reaches the size below then older entries will be deleted Maximum file size KB 200 Connections Heartbeats Redundancy Shutdown Settings RCCMD Bindings Notification Settings Advanced Settings The information below defines IP address and TCP port of the RCCMD Listener Web Configuration IP address 0 0 0 0 means all addresses 0 0 0 0 16003 Note IP address 0 0 0 0 means every local address default TCP Port is 6003 v Done Figure 185 RCCMD Weblnterface Advanced Settings Click the Save Changes button prior of the leaving of this site to save your changes You can change the default password for the user admin into the menu Web Configuration In addition you can disable the HTTPS protocol if you just want to use the HTTP protocol The RCCMD version 4 2 3 0 or higher provides the feature of changing the default ports for HTTP and HTTPS DOG Advanced Settings Mozilla Firefox s 100ls Help lt v A http localhost 8080 Options weblfManagement htm v bi v Goo EN Most Visited 6 Getting Started latest Headlines v 6 Advanced Settings an v GENERE x lt v Options The information below is used to log on to this user interface Administrator User Name admin Connections Current Administrator Password Heartbeats New Administrator Password Redundancy Select the access protocol for this user interface Shutdown
94. e the settings IMPORTANT RCCMD as service with local desktop interactions is permitted to execute local shutdowns for this action no user rights except administrative rights are required But for any user specific actions e g starting a net send message or any other 38 command the RCCMD may need extra rights These rights have to configured in the Control panel services Sending of a message to all RCCMD clients To send a message to all RCCMD clients please use the following syntax rccmd se MSG TEXT ups says hello world a 192 9 200 255 The RCCMD client which should receive this message need to get the entry of the ip address of the RCCMD sender or rather the list should be empty The CS121 is not able to send UDP broadcasts so you have to enter the above mentioned syntax into the RCCMD client The client will operate as relay station and will forward the message It is no problem to send the message from a Windows UNIX or MAC OS RCCMD sender 2 9 Testing the RCCMD connection Finally test your configuration if all RCCMDs are present and working For this you may use the RCCMD in the Debug mode Syntax RCCMD debug s l a so that you have screen output PING every remote computer with the command ping hostname IP address If the PING works fine you can now start to test the RCCMD connection with the debug mode If everything works fine you will see that a connection is established and
95. ebaddeninadderentt 31 Figure 39 Settings Confirmation cccccccccssseessescecesceeeeeeeceeseesssseeccsscoeeceeeseeeesnenesssseoees 32 Figure 40 SSLC niigurationuaavasdvseeese in ae aR 32 Figure 41 RCCMD Properties WiINdOW cccccccccccccceceesseeeeeeeeeeseeeeeeeeeeeeeeeaaeaaeeaeaaaaaaaaaeas 34 Figure 42 RCCMD Properties Log On Window ccccccccccccceeeeeeseeeeeeeaeeaseeeaaeeaaaaaeaaaaaaaes 34 Figure 43 RCCMD Properties Password Confirmation cccccccccccccccccceccseesssseeseessaaeeeeees 35 Figure 44 Select User Window cccccccccccccccccecseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeauanaaeaaaaaaaaaaaaaaaaaaaaes 35 Figure 45 Selection of the Object Name ccccccccccccceceeessseeeeeeeeeeeeeeeeeeeeeeaeaeaeeaaaaeaaeeaeaes 36 Figure 46 Administrator Selection ccccccccccccccccceeeseeceeeceeeceeeceeeeeeeeeeeeeeeeauauaaaaeaaaaaaaaaaaaaas 36 Figure 47 Administrator Password Confirmation ccccccceeeeeeeeeeeeeeeeeenneeeeeeeeeeeeeeeeeeeeaas 37 Figure 48 Client Installation successful Window ccccceeeeeeeeeeeeeeeeeeennneeeeeeeeeeeeeteeeeeeaas 38 Figure 49 RGGMD Console Test ua 39 Figure 50 RCCMD Alive Check via Command Line rrrrnnnnnnnnnnnnnnnnnnnrrrnnvvvnnnnensrnnsnnnnnnnnnnnnn 40 Figur 52 ROCGMD Corfiguratin nananana aa A N N 43 Foure 53 Gen ns Alm rsrsr an a a E ease 44 Figure 54 Add IP Address Wind OW isas sad aad aad A A E 44 Figure 55 Advanced Network Settings
96. ed Broadcast Message from 192 168 202 21 Broadcast Message from 192 168 202 92 Broadcast Message from 192 168 202 21 Broadcast Message from 192 168 202 21 RcevThreadudp stopped RCCMD Listen Mode stopped RcvThreadUdp started SendThreadCheckUpsman started RCCMD Listen Mode started Broadcast Message from 192 168 202 29 Broadcast Message from 192 168 202 29 Broadcast Message from 192 168 202 29 RcevThreadudp stopped RCCMD Listen Mode stopped SendThreadCheckUpsman stopped SendThreadCheckUpsman started RcevThreadudp started RCCMD Listen Mode started Broadcast Message from 192 168 202 29 Broadcast Message from 192 168 202 29 Broadcast Message from 192 168 202 29 Broadcast Message from 192 168 202 21 RevThreadudp stopped RCCMD Listen Mode stopped SendThreadCheckUpsman stopped SendThreadCheckUpsman started RcevThreadudp started 38 38 RCCMD RCCMD Listen Mode started Figure 60 RCCMD Log File received received received received received received received received received received received Step 8 If you want to send emails via RCCMD click the Configure button 48 Logfile configuration Max logfile size 512 Kb Execute at mail signal from RCCMD server C Program Files RCCMO mail bat V Enable E Mail Client Outgoing Server SMTP mail somewhere com Sender E Mail Address someone somewhere com RCCMD ver 4 0 2 3 V Use Server Authentication Account User
97. else RCCMD cannot shutdown the the other virtual machines Redundan and hosts Enter the virtual machine s name on which RCCMD runs vMA55_ES Shutdown Settings e Notification Settinas ESXi Hosts to shutdown VMware Settings ESXi Address Shutdown duration Verified Advanced Settings e Web Configuration Total estimated Shutdown time for the System with current configuration 00 01 30 Save Changes Figure 160 RCCMD W ebinterface Remote Access VMware Settings Select Virtual Machine Management within ESXi to let the ESXi handle the virtual machines at shutdown time 121 You can verify the access data and the connection to the ESXi host via the Verify button D Attention Please note that the name of the vMA in the RCCMD menu VMware Settings has to be identical with the name of the vMA in the vSphere Client or rather vCenter Q https 192 168 200 103 8443 Options vmwareSettings htm Cc v Google VMware Settings v Options within ESXi v Virtual Machine Management e Connections 2 e Hanssibente The virtual machine that runs RCCMD must not be shutdown Or else RCCMD cannot shutdown the the other virtual machines e Redundan and hosts Enter the virtual machine s name on which RCCMD run vMASS_ES Shutdown Settings Notification Settinas ESXi Hosts to shutdown VMware Settings Advanced Settings Web Configuration ESXi Add
98. enu Redundancy The redundancy level defines the number of redundant senders in the redundancy group This means that level 1 senders must have sent a shutdown signal before this RCCMD starts its shutdown sequence When redundancy suppresses a shutdown then RCCMD will trigger the suppressed bat You can edit this file if you click the Edit file button 21 http localhost 8080 Options redundancy htm Datei Bearbeiten Ansicht Favoriten Extras W Favoriten 9 Web Slice Katalog v Redundancy Redundancy v Options The redundancy level defines the number of redundant senders in the redundancy group This means that level 1 senders must have sent a shutdown signal before this RCCMD starts it s shutdown sequence e Connections Heartbeats V Enable RCCMD redundancy function Redundan gt Shutdown Settings Redundancy Lev l Notification Settings V 192 168 222 210 Advanced Settings 7 192 168 222 209 Web Configuration When redundancy supresses a shutdown then RCCMD will use the following setting Run this command file C Program Files RCCMD Shutdown Suppressed bat Edit File Figure 22 RCCMD W ebinterface Configurator Redundancy Please note that it is required to configure a reset of the redundancy alarm on the sender CS121 UPSMAN You can use the function Send RCCMD cancel shutdown to discard a previously sent shutdo
99. er SEA Lasses aa 97 Figure 127 RCCMD UNIX Check Upsman arrocar aion 98 Figure 128 RCCMD UNIX Log File Options rrrnrrrnrrrrrrrrrrrrrrrrrvrrnvrrrrrrrrrvrrnrrrrrrrnrsrnnnnnnnnnen 99 Figure 129 RCCMD UNIX Shutdown Options rrrnnnnnrrrrrvnvnvnnvrrrvrrnrrrrrnnnnrrrrrnnneeernrrrrrrrnnn 100 Figure 130 RCCMD UNIX File Browsing rrwrarrrrrrrnnnnnrrvvvvnnenvnnnnrrnnnrrrrsnnnnrrvnenennnereessnennn 101 Figure 131 VMWare Product saa 103 Figure 132 ESX License Erot Lusmssanieneatnm nm E REEE 106 Figure 133 A RCCMD shutdown will be send to the optional RCCMD clients on the virtual machin s than 10 116 ESX MOS bast ee ae ee es es ed 106 Figure 134 vSphere Client Configuration ccccccccccccccccceeeseeeeseeeeaeeeeeeeeeeeaeaeaeaaaaaaaaaaaaaas 107 Figure 135 vSphere Client Auto Start Configuration rrrrnrrnnnnnnrrnnnnnnrrnnnrrrnnnnnernnrrrrrrrnnn 107 Figure 136 vSphere Client Auto Start Delay rrrrrrrrnnrnnnvrrnvrrnrnvrnnnrrnnrrrrrrnnnrrnnrrrrrrnnnnneen 108 Figure 137 vSphere Client Startup and Shutdown 1 00 cece eee eee eeeeeeeeeeeneeeeeeeeeeeeeees 108 Figure 138 Preparation of the installation eeeerrrrrrrrrrrrrnrrnrrnrnrrnnnrnrrnrnrnenennnennnnnennnnnnenn 110 Figure 139 Execution of the binary file and start of the installation ccc 110 Figure 140 Introduction OS reCOQnition cccccccceessessessnssnnseeeeeeeeeeeeesesseseeenaseeeeeeeeeeeeess 111 Figure 141 AGOMD License KEV uansett ede
100. essage Notification Web Configuration When RCCMD receives a message signal it will use the following setting Run this command file fusrirccmd irccmd_message sh Execute Notification When RCCMD receives an execute notification it will use the following setting Run this command file fusrirccmd rccmd_execute sh Edit File Nane Figure 93 RCCMD Weblnterface Notification Settings Click the Save Changes button prior of the leaving of this site to save your changes You can define the maximum size of the event logfile into the menu Advanced Settings where the overwriting of older entries will start the RCCMD bindings for the IP address the RCCMD listener TCP port and the RCCMD Tray Message Port which will be used for the RCCMD messages In addition you can disable the Start Jobs as interactive user feature that means if disabled that RCCMD will execute jobs if nobody is logged in on the system 72 DOG Advanced Settings Mozilla Firefox lt a v E A http localhost 8080 Options advancedSettings htm v Google Q Most Visitedv Getting Started latest Headlines v 6 Advanced Settings op v 0 0 0 0 0 0 0 1 v Options When the event log file reaches the size below then older entries will be deleted Maximum file size KB 200 Connections Heartbeats Redundancy Shutdown Settings RCCMD Bindings Notification Settings
101. et To Defaults Stored value is equal to the default Figure 207 Raritan SNMP Settings Click on Stop change the configuration on Write Community e g to public2 and restart 164 E Figures Figure 1 RCCMD and UPSMAN in a network environment rvrvrvrvrvrrvrrvrvrrrrvrrrrrrrrrrnnennnnnn 7 Figure 2Imr0aueNohuavssaeses STE ed 8 Figure S License Key EINA 8 Figure 4 LICENSE Agreements errn opne ar EaR AET ETETEA TERES 9 Figure 5G MOOS ES IST AC Hav 9 Figure 6 Install Folder Selection sx scccecccccvce cxccewce cweccwcc tas cx wie seecved xetevediwicawdeiecesed Aecesadlecessdeds 10 Figure 7 Firewall Exceptions caa sua anal aad a an etal ace ibae daa Sassari sccinly 10 Figur 8 RCGMO Tray r t r eeu E aaa 11 Figure 9 Shortcut Folder Selection ccccccsssessseeesececeeeeeeecessensesssccceeceeeseneneressnenesssseooss 11 Figure 1 OS UMIMIAly EE 12 Fore TISSE NE ASS 12 Figure 12 Installation Gomplet uorsrorsesrasealelkenmsenikeneeneanenesnpsessine 13 Figure 13 Content of the installer propertieS cccccssssseececcessseeeeccseeeseeceesseeaaseeeeeseseaes 15 Figure 14 RCCMD Console Installation Language Selection Introduction 0 17 Figure 19 RCCMD Weblnterface Certificate Error rrrrnnrrnnnnrrrnnnnnrrrnrrrrnnnnnnnnnnnnrrrnnnnnnnnnn 19 Figure 20 RCCMD Weblnterface Configurator Connections rrrnnrrrrrrnnvvnnnrnrvrrnnnnnnnnnn 20 Figure 21 RCCMD Weblnterface Con
102. executed when an alive check fails Default rccmd notalive sh AliveProg usr rccmd rccmd notalive sh 127 HE HH Redundancy Mode Enable Redundancy Defines if we should operate in redundancy mode Requires an enabled lt Alive Check gt configuration Default false RedundancyEnabled false Redundancy Group Members List A list of redundancy group member addresses must be also in lt AliveAddresses gt Seperate IP addresses with a space e g 192 168 0 1 192 168 0 2 Default lt empty gt No redundancy available RedundancyAddresses Redundancy Level Defines how many of the lt RedundancyAddresses gt are redundant Shutdown is executed when the number of shutdown requests exceeds this number Default 0 No redundancy available RedundancyLevel 0 Enable Redundancy Script Defines if we should NOT execute a script when redundancy suppresses a shutdown Default false RedundancyBatchSuppress false Redundancy Script Full path to script that is executed when redundancy suppresses a shutdown Default ShutdownSuppressed sh RedundancyBatchFile usr rccmd ShutdownSuppressed sh SSL encryption enables SSL encrypted messages RCCMD SSL false Rejection Acceptance of expired Certificates disables SSL communication that try to use expired certificates SSLRejectExpiredCert false ExecProg usr rccmd rccmd execute sh HH vCenter true shutdownHosts 192 168 200 34
103. figurator Heartbeats cseceeeeeeeeeeeeeeeeeeeees 21 Figure 22 RCCMD Weblnterface Configurator Redundancy vvvvvrvvvvvvvvvvvvvvvvrvvvvrnvnnnnen 22 Figure 23 RCCMD Weblnterface Configurator Shutdown Settings ceeeeeeee 23 Figure 24 RCCMD Weblnterface Configurator Shutdown Settings Edit File 23 Figure 26 RCCMD Weblnterface Configurator Notification Settings eee 24 Figure 27 RCCMD Weblnterface Configurator Advanced Settings cccccceeeeseeeeeees 25 Figure 28 RCCMD Weblnterface Configurator Web Configuration cccccceeeeeee 26 Figure 29 RCCMD Weblnterface Configurator View Event Log ccccceeeeeeeeeteeeeeees 26 Figure 30 RCCMD Weblnterface Configurator System Status rrnnrrrrnnnnnnnnnnnrrrnnnnnnnnnn 27 Figure 31 RCCMD Weblnterface Configurator Hel ccceceeeeeceeeeneeeaeeeeeeeeeeeeeeeeeeeeeaas 27 Figure 33 Example Batch File ROCMD act as Relay Station srrrnnnnnnnnnrrrnnnnnnrnnnrrnnnnnennn 28 Figure 34 CS121 Configuration WAKEUP Command cccccccccccccceeeseeeeeeeeeeaseeeeaeaees 29 165 Figure 35 UPSMAN Configuration WAKEUP Command eee 30 Figure 36 WAKEUP Command into RCCMD Log File ccceccceeceeeeeeeeeeeeeeeeeeeeeeeeeeees 30 Figure 37 RCCMD SSE Settings ssc ccc aea a 31 Figure 38 Timeserver Setings uuuvavadsuaidunsduaddundeuniktemanadd
104. from your UPS into the CS121 The job Send RCCMD cancel shutdown would be set into these all clear events so that e g at restart of the UPS the event UPSMAN STARTED would reset the accordant RCCMD client automatically Alternative Should the job Send RCCMD cancel shutdown not be present into your CS121 UPSMAN or BACS WEBMANAGER you can use the job Send RCCMD shutdown to remote client or rather Send RCCMD execute to remote client alternatively The parameter VWAKEUP got the same function like the Send RCCMD cancel shutdown and resets the redundancy alarm of a RCCMD Client into initial state For this the events POWER RESTORED BATTERY LOW OFF UPSMAN STARTED and GENERAL ALARM OFF are suitable too to configure the function Send RCCMD command to remote client with the W AKEUP command Power restored Job 3 Function Send RCCMD Command to remote client Client IP 192 168 200 17 Client Port Default 6003 5003 Command WAKEUP 554 Command Figure 34 CS121 Configuration WWAKEUP Command Click into the CS121 menu Events Alarms onto Power restored and add a new job Select the function Send RCCMD command to remote client set the accordant IP address of the RCCMD client and enter the command WAKEUP 29 Insert Function Function Send ACCMD EXECUTE to remote client Function Parameters Parameter Value ADDRESS 192 168 200 1
105. have to assign a system value UNZIP DKA200 VMS ALPHAJUNZIP EXE where DKA200 is your CDROM device Unpack your VMS UPS archive SET DEF DKA100 TEMP UNZIP RCCMD ZIP Start the VMS installation routine SYS UPDATE VMSINSTAL RCCMD DKA100 TEMP Configuration procedure After the installation there are 3 command files RCCMDSTART COM RCCMD startup command file should be called in the VMS startup file RCCMD COM Command file to start RCCMD program itself this should be configured to your requirements RCCMD_SHUTDOWN COM sample command file which could be called by RCCMD to shutdown VMS Configure the RCCMD COM command file by calling the RCCMD program with the following command rccmd l optional you can use rccmd a lt IP address of the sender gt p lt port standard 6003 gt After that you can start the RCCMD by caklling the command file RCCMDSTART COM with rccmdstart Check the process by calling show system There should be a process with the name RCCMD The automatic startof the RCCMD should be initiated from the VMS startup file You may use the enclosed script rccmdstart com Add a line to your startup file prior to the exit command your_disk your_path rccmdstart com e g dka100 ups rccmdstart com The UPS software will be started automatically after the next reboot 9 RCCMD AS400 Client RCCMD for AS 400 an iSeries is not described in this manual b
106. he disk Macintosh HD Disk Space Information for Installation Target Required 31 002 465 Bytes Figure 175 RCCMD Pre Installation Overview Press the Enter key to finish the installation Select these default values for the port and protocol of the web interface or select new ones 133 The default port appears to be free Select these default values for Port and Protocol for RCCMD Weblf or choose new ones Access Protocol Default http http RCCMD Weblf Port Default 8080 8000 Figure 176 RCCMD Set Weblf Access Please note the following It is necessary to configure RCCMD Please use the web interface at http lt address of this computer gt 8088 Should you decide to run RCCMD with this default configuration RCCMD will accept messages from any ip address Please set one or more valid ip addresses that are allowed to send shutdown messages to this RCCMD Figure 177 RCCMD Configuration required 134 eo RCCMD Client Congratulations RCCMD Client has been successfully installed to usr rccmd Press Done to quit the installer Figure 178 RCCMD Install Complete 6 1 RCCMD Weblnterface from Version 4 2 0 0 RCCMD provides its own web interface from version 4 2 0 0 or higher Therefore it is possible to configure and control RCCMD remotely After the successful installation your default web browser of your OS starts automatically
107. he file shutdown sh on your XEN Server when any CS121 or UPSMAN transmit a RCCMD shutdown call This file shutdown sh makes an init O shutdown on your XEN Server edit this file if you want to use a different shutdown procedure Advice We recommend to install RCCMD on the virtual guest systems too and to shut them down PRIOR of the shutdown of the physical host Therefore the secure shutdown of the guest systems is assured and avoids the lost of their data 6 RCCMD on MAC OS 10 X Note The RCCMD Installer is using our delivered Java Runtime Environment version which is used for the installation or rather uninstallation only In addition the RCCMD Web Configurator is using a Java web server jetty If you want to use RCCMD without Java delete the entry System Library Startupltems RccmdW eblf till MAC OS 10 5 or since MAC OS 10 5 Library LaunchDaemons de generex rcmdW eblf plist 130 InstallAnywhere will guide you through the installation of RCCMD Client It is strongly recommended that you quit all programs before continuing with this installation Click the Next button to proceed to the next screen If you want to change something on a previous screen click the Previous button You may cancel this installation at any time by clicking the Cancel button Installer version 196 Figure 170 RCCMD Installation Welcome You need a special license key for your RCCMD software You can identify
108. hted then press Enter To reset all values to their defaults select the Default button by hitting the Tab key then press Enter To leave the Screen select either Ok or Cancel with the Tab key and press Enter Ok means accept all values as displayed on the screen Cancel means discard all changes made to the screen and switch back to the previous state Exit rccmd conf 100 In the main configuration menu Rccmd Configuration select either Save or Exit by hitting the Tab key until the desired button is highlighted and press Enter Save means rccmd cfg will be written according to the actual values of the configuration screens Exit will just exit the program leaving rccmd cfg untouched The File Browser Some of the screens above use a small build in file browser like this generex host usr ups select file to execute File usr ups Default Figure 130 RCCMD UNIX File Browsing The 1 and keys may be used to move the list up and down Pressing the Enter key will select the highlighted entry If the selected entry is a directory the browser wil move into this directory and list its contents As usual the double dot means the parent directory File types are indicated similar to the output of Is F This means a is appended for executables for directories for symbolic links and for sockets UNIX RCCMD multiple sender configuration V1 V2
109. htm v tay a ip Most Visited 6 Getting Started Latest Headlines v Redundancy SF 0 0 0 0 0 0 0 1 Redundancy v Options The redundancy level defines the number of redundant senders in the redundancy group This means that level 1 senders must have sent a shutdown signal before this RCCMD starts It s shutdown sequence Heartbeats s Enable RCCMD redundancy function Redundancy 1 ae a 192 168 222 209 Settings 7 192 168 222 210 When redundancy supresses a shutdown then RCCMD will use the following setting Run this command file lusrirccmdl ShutdownSuppressed sh Figure 156 RCCMD WeblInterface Redundancy Please note that it is required to configure a reset of the redundancy alarm on the sender CS121 UPSMAN You can use the function Send RCCMD cancel shutdown to discard a previously sent shutdown automatically If a shutdown was suppressed because of the existing redundancy at this point of time but the problem was solved at the UPS intermediate you can reset the shutdown with the function Send RCCMD cancel shutdown The client which received the shutdown will be encouraged to reset it Please take a look into chapter 6 1 for further information about RCCMD with redundancy Click the Save Changes button prior of the leaving of this site to save your changes You can change or rather extend the shutdown sequence into the Shutdown Settings menu The shutdown bat will be executed
110. iguration changes Save Exit amp Reboot Write all changes to flash memory and reboot the C5121 Please be patient after clicking here Figure 105 Settings Confirmation Start the RCCMD Web Configurator again and enable the SSL network feature http localhost 8080 Options connections htm Datei Bearbeiten Ansicht Favoriten Extras gly Favoriten 33 amp Web Slice Katalog v Connections er ae 0 0 0 0 0 0 0 1 v Options The list below identifies all senders that are allowed to connect to this listener Note An empty list means that every sender can connect to this listener Connections Heartbeats Sender IP Address Redundancy 192 168 222 113 Shutdown Settings Notification Settings Advanced Settings Web Configuration Protocol Reject expired SSL certificates Figure 106 SSL Configuration If you want to accept expired certificates please enable the accordant function 19 3 7 1 RCCMD with own SSL certificates In this chapter we will describe how to use an own SSL certificate with RCCMD e g OpenSSL http www openssl org Be your own CA Using OpenSSL it is quite simple to become your own CA Just run CA pl newca Done Just ensure that you select a useful CN common name Create your RCCMD certificate You need to create your certificate for RCCMD now As it will use it for verification it should contain the same useful common name CN
111. igure 95 RCCMD W ebinterface Web Access 73 Click the Save Changes button prior of the leaving of this site to save your changes You can see the logging of the events into the menu Status Event Log DOG RCCMD Configurator Mozilla Firefox story Bookmarks To lt v amp a http focalhost 8080 Status viewEventLog htm v SB v Goog N Most Visitedv 6 Getting Started Latest Headlines v 6 RCCMD Configurator oF v 0 0 0 0 0 0 0 1 Y Status Event Log e View Event Log These are the events that have occured on this computer System Status Date a Time FEN 2012 10 18 15 23 22 rccmd 03915 Copyright c GENEREX GmbH 1996 2010 All rights reserved 2012 10 18 15 23 22 rccmd 03915 UPSMAN RCCMD MASTERKEYCODE testing purpose only do not use for customer installations 2012 10 18 15 23 22 rccmd 03915 V4 2 3 0 Unix Remote Command Program 2012 10 18 15 23 23 rccmd 03923 Listen Mode started 2012 10 18 15 23 23 rccmd 03923 RevThreadUdp started Done Figure 96 RCCMD W ebinterface Event Log You can check the current status of RCCMD into the menu Status System Status update the status and restart or rather stop start the RCCMD service DOG System Status Mozilla Firefox File Edit View History Bookmarks Tools Help lt a v e A http localhost 8080 Status systemStatus htm v Go0 oN Most Visited v Getting Started latest He
112. ill trigger the suppressed bat You can edit this file if you click the Edit file button 70 Redundancy Mozilla Firefox v g A 6 http localhost 8080 Options redundancy htm v tay a ip Most Visited 6 Getting Started Latest Headlines v Redundancy SF 0 0 0 0 0 0 0 1 Redundancy v Options The redundancy level defines the number of redundant senders in the redundancy group This means that level 1 senders must have sent a shutdown signal before this RCCMD starts It s shutdown sequence Heartbeats s Enable RCCMD redundancy function Redundancy 1 ae a 192 168 222 209 Settings 7 192 168 222 210 When redundancy supresses a shutdown then RCCMD willl use the following setting Run this command file lusrirccmdl ShutdownSuppressed sh Figure 91 RCCMD Weblnterface Redundancy Please note that it is required to configure a reset of the redundancy alarm on the sender CS121 UPSMAN You can use the function Send RCCMD cancel shutdown to discard a previously sent shutdown automatically If a shutdown was suppressed because of the existing redundancy at this point of time but the problem was solved at the UPS intermediate you can reset the shutdown with the function Send RCCMD cancel shutdown The client which received the shutdown will be encouraged to reset it Please take a look into chapter 6 1 for further information about RCCMD with redundancy Click the S
113. in the redundancy group This means that level 1 senders must have sent a shutdown signal before this RCCMD starts its shutdown sequence When redundancy suppresses a shutdown then RCCMD will trigger the suppressed bat You can edit this file if you click the Edit file button 137 Redundancy Mozilla Firefox v g A 6 http localhost 8080 Options redundancy htm v tay a ip Most Visited 6 Getting Started Latest Headlines v Redundancy SF 0 0 0 0 0 0 0 1 Redundancy v Options The redundancy level defines the number of redundant senders in the redundancy group This means that level 1 senders must have sent a shutdown signal before this RCCMD starts It s shutdown sequence Heartbeats s Enable RCCMD redundancy function Redundancy 1 ae a 192 168 222 209 Settings 7 192 168 222 210 When redundancy supresses a shutdown then RCCMD will use the following setting Run this command file lusrirccmdl ShutdownSuppressed sh Figure 182 RCCMD WeblInterface Redundancy Please note that it is required to configure a reset of the redundancy alarm on the sender CS121 UPSMAN You can use the function Send RCCMD cancel shutdown to discard a previously sent shutdown automatically If a shutdown was suppressed because of the existing redundancy at this point of time but the problem was solved at the UPS intermediate you can reset the shutdown with the function Send RCCMD can
114. ince all other UPS are still reading OK or did not yet send any shutdown the shutdown is suppressed 3 shutdown signals would create messages in the above example redundancy level 3 only just the 4 signal would initiate the shutdown fl RCCMD Configuration lt Addresses Functions Logfile Execute Control g B Max logfile size 1024 Kb cf UPS UPSMAN IRCCMDCFG V4 0 0 11 Figure 110 Configuration RCCMD Log File 85 You can configure the log file size and edit the executing sh files The RCCMD version 4 0 2 0 provides a grafical configuration of the shutdown sequence Logfile Breene Control Execute at mail signal from RCCMD server fusr reemd rcemd_mail sh edt Fil Execute at message signal from RCCMD server fusr reemd recmd_message sh Edit File Execute at execute signal from RCCMD server UPSMAN usr rcemd rccmd execute sh Edit File Execute at shutdown signal from RCCMD server fusr rcemd rcemd_shutdown sh JRCCMOCEG V4 0 2 0 Figure 111 Configuration RCCMD Execute Click the Configure button to enter the shutdown sequence settings File usr rccmd rccmd shutdown sh Available Commands Current Sequence RCCMD shut down relay IRCCMD shut down relay to gx56 ssl Wait seconds RCCMD shut down relay to 111 111 111 1 Restart System RCCMD shut down relay to 111 111 111 1 RCCMD shut down relay to 111 111 111 1 RCCMD shut down relay to 111 111 111 1 RC
115. ion Configure Shutdown Sequence File usr rccmd rccmd shutdown sh Available Commands Current Sequence Ea s s Configure RCCMD shutdown relay Enter IP address or hostname of the remote computer gx77 you want to shutdown with the RCCMD o AND OR Enter an IP range of remote computers you want to shutdown with RCCMD e From 192 168 222 200 To 192 168 222 Use secure connection SSL or Descriptio Relays RUCMD shutdown command to anotner computer Enter IP address or hostname or the remote computer you want to shutdown Save Cancel Figure 117 RCCMD Shutdown Relay If you want to remove single IP addresses mark the line with its desired IP address and click the lt button Additionally you can enable the SSL function 3 10 UNIX RCCMD Configuration With CURSES Library G Note This section does not apply to rccmd V1 for Unix in addition it only applies to rccmd running in Listen mode This tool rccmd_conf is not supported by newer operating systems If you try to start on not supported OS you will receive an error message about missing curses library Recmd V2 running in Listen mode may be configured using a configuration file By default rccmd will look for a file named rccmd cfg in its startup directory usually usr ups This file may be generated using rccmd conf Rccmd_conf is a small curses based utility which runs o
116. is default configuration RCCMD will accept messages from any ip address Please set one or more valid ip addresses that are allowed to send shutdown messages to this RCCMD Cancel Figure 79 Installation Configuration Advice Choose RCCMD start 60 REEMD Glient If you want to start it manually use usr rccmd rccmdctl start Do you want to start RCCMD now Figure 80 Installation Start RCCMD now So RCCMD has been installed successful REEMD Glient Congratulations RCCMD Client has been successfully installed to usr rcecmd Press Done to quit the installer Figure 81 Installation Install Complete 3 2 Silent Installation of the RCCMD Installation A Silent Installation is an automated installation procedure where the user inputs are received from a response file This allows the user to install a software product without user input or graphical interface The RCCMD Software provides a silent installation but it is required to enter some settings into the installer properties file This file is located into the CD folder Recmad Linux 12 This file provides Values to alter the behaviour of the installer You can preset Values for some internal Variables For the installer to find and use this file it is necessary to either rename this file or pass a parameter to the installer when calling it If this file is called installer properties or has the same n
117. it file RCCMD ver 4 0 2 3 lt Back Install Figure 63 RCCMD Shutdown Sequence Configuration The following commands are available for the shutdown sequence configuration GP ATTENTION The shutdown sequence will be executed from top to down The Shutdown Windows command should be at the bottom because after the execution of the shutdown no other commands will be executed Log off user Ends your session leaving the workstation on full power Hibernate Windows Hibernates your session the content of the RAM will be written on hard disk Power off Windows Ends your session shuts down Windows and turns off the power Restart Windows Ends your session shuts down Windows and restarts Windows Suspend Windows Suspends your session the content of the RAM will NOT be written on hard disk Quit Lotus Notes Closes Lotus Notes prior of the shutdown of Windows Please configure a Wait delay after this command Quit Siemens SIMATIC Closes WIN CC Database prior of the shutdown of Windows Please configure a Wait delay after this command 50 Quit applications Closes all applications prior of the shutdown of Windows Wait some seconds Waits a duration in seconds until the next command will be executed RCCMD shutdown relay Relays RCCMD shutdown command to another workstation Enter the IP address or the hostname of the remote station you want to shutdown Shut down Windows E
118. ith a different operating system in heterogene network the RCCMD tool is necessary The RCCMD tool is based on the TCP IP protocol During the installation the TCP IP protocol should be installed in the first place The RCCMD tool works in two different modes In the so called Listen mode the program as UNIX daemon in a background process waits for a command from the Send mode of the RCCMD modul D Note The RCCMD Installer is using our delivered Java Runtime Environment version which is used for the installation or rather uninstallation only In addition the RCCMD Web Configurator is using a Java web server jetty You can delete the RCCMD Web Configurator out of the autostart etc init t recmdConfig or rename the symlink usr rccmd runRecmdConfig Then RCCMD is running without Java ATTENTION If you got an OS without grafical interface please take a look into the FAQs how to mount a USB stick 3 1 RCCMD Installation on UINIX OS It is required to install RCCMD as user root out of a rootshell or a graphical terminal Extract the file rccmd tar copy it to a temporary folder and start the program installRCCMD bin The following graphical installation will start 55 RGEGMD Glient InstallAnywhere will guide you through the installation of RCCMD Client It is strongly recommended that you quit all programs before continuing with this installation Click the Next button to proceed to the next screen If you
119. k the Test connection s button the UPSMAN alive checking of the entered IP addresses will start port 5769 will be tested If you click the Browse button you will get a selection of the default sh files At UPS installation RCCMD offers redundancy management functionality as follows Every UPS must be equipped with a CS121 or UPSMAN software computer When ticking the box use RCCMD group redundancy you are guided to a menue where you can choose which CS121 UPSMAN are supplying this RCCMD client E g if 4 CS121 UPSMAN are installed into 4 UPS than each may send a shutdown signal to this RCCMD client 84 fi RCCMD Configuration Addresses Functions Logfile Execute Control UPSMAN alive checking g 3 ETE JE a L 5 Polling rate O E Connection retries Execute at failure UPSMAN fusr recmd rcemd execute sh Default Setti Edit File 3 RCCMD Redundancy Use RCCMD group redundancy UPS IRCCMDCFG VW4 0 0 11 Figure 109 Configuration RCCMD Redundancy The redundancy level defines how many shutdown signals are required to execute the shutdown bat file As long as this number is not exceeded the RCCMD client will react on such a shutdown signal only with a messagebox Execute command when redundancy suppresses a shutdown box This will show a message to inform the user that there has been a shutdown signal from one of the UPS in the group but s
120. lice Katalog v 8 Advanced Settings fom ve con The information below is used to log on to this user interface Administrator User Name Current Admmistrator Password New Administrator Password Select the access protocol for this user interface sm HTTP No Securty Note Changes in protocol will become active upon the next start up Port for http Port for https Figure 28 RCCMD W ebinterface Configurator Web Configuration Click the Save Changes button prior of the leaving of this site to save your changes You can see the logging of the events into the menu Status Event Log Gos http localhost 8080 Status viewEventLog htm Datei Bearbeiten Ansicht Favoriten Extras s r Favoriten 925 E Web Slice Katalog v RCCMD Configurator v Status Event Log View Event Log These are the events that have occured on this computer tem Status Date a Timea 2012 10 17 15 21 52 RCCMD Copyright c 1996 2012 Generex GmbH 2012 10 17 15 21 52 RCCMD RCCMD Listen Mode started 2012 10 17 15 21 52 RCCMD RCCMD V4 0 2 1 Windows NT Remote Command Program 2012 10 17 15 21 52 RCCMD RcvThreadUdp gestartet 2012 10 17 15 27 10 RCCMD RCCMD Listen Mode stopped 2012 10 17 15 27 10 RCCMD RcvThreadUdp angehalten 2012 10 17 15 27 12 RCCMD Copyright c 1996 2012 Generex GmbH 2012 10 17 15 27 12 RCCMD RCCMD Listen Mode started 2012 10 17 15 27 12 RCCMD RCCMD V4 0 2 1 Windows NT Rem
121. llation If you want to change something on a previous step type back You may cancel this installation at any time by typing quit Figure 82 Console Installation Language Selection Introduction It continues with the OS and platform detection the RCCMD license key and the license contract 65 OS amp CPU architecture unknown unknown GNU Linux PRESS lt ENTER gt TO CONTINUE Enter your license key Usually the license key is located on the installation booklet or on a label on the reverse side of the CD sleeve Enter license key 12SHARX3 1234567 Installation and Use of RCCMD Client Requires Acceptance of the Following License Agreement Copyright The information contained in the manual of this product is nonconditional and may be changed without due notice GENEREX nor the reseller of this product undertakes no obligations with this information The software described in this brochure is given on the basis of a license contract and an obligation to secrecy i e an obligation not to further publicise Figure 83 Console Installation OS Detection License Agreement Select the features you want to install or press the Enter key if you want to use them all ENTER A COMMA SEPARATED LIST OF NUMBERS REPRESENTING THE FEATURES YOU WOULD LIKE TO SELECT OR DESELECT TO VIEW A FEATURE S DESCRIPTION ENTER lt NUMBER gt PRESS lt RETURN gt WHEN YOU ARE DONE 1 X RCCMD 2 X WebIf 3 X
122. m Otherwise it is enough if the computers will be shut downed via RCCMD if a powerfail occurs If the computers are down there are no open data anymore that can be lost You could switch off any NAS as soon as the network computers are down Specific feature QNAP NETAPP systems are using the sync mode and are therefore faster and more sensitive accordingly but these devices possess an own battery to assure a secure shutdown at any time This internal battery clears the cache and parks the recording head if no data have to be stored So you will not lose data if the network computers are down We do not think that an additional cable connection between the UPS and the NAS is required if it is assured that the computers are down Problem Error messages at UPSMAN Alive Check on Windows Server 2008 Solution The firewall port 5769 has to be enabled for all profiles domain home public Problem Mount of USB stick via command line Solution Change into the directory dev Execute Is There you will see the connected devices Note the devices like sda sda1 Connect your USB stick Execute Is again into dev Now you should see more entries under sda My stick got the entry sdc1 Enter the following mount dev sdc1 mnt Use this command on FreeBSD OS mount msdosfs dev da0s1 mnt usb Execute Is lisa Now you should the folders of your stick Change into the accordant directory cd mnt name of the folder which
123. n using the Tab key and press Enter otherwise select Cancel Configure Check Upsman Upstcp The Recmd listener has the ability to check periodically if the Upsman Upstcp servers configured in Access Control List are alive D Note The Check Upsman Upstcp feature is only available if there are any addresses configured in the Access Control List 97 If there are one or more entries in Access Control List the screen Check Upsman Options pops up E generex host usr ups Check Upsman Options Enable check Upsman Upstcp feature falselj Enter the interval for upstcp connects in minutes 30 File to execute usr ups rcemd notalive sh rsresreeee Cancel Browse Default Figure 127 RCCMD UNIX Check Upsman Use the Tab key to move through the option fields and buttons Enable check Upsman Upstcp feature Possible values are true and false false is the default To change the value use the 1 and keys Enter the interval for upstcp connects in minutes Interval to connect Upsman Upstcp servers in minutes Default is 30 minutes To change overwrite the value in the options field File to execute This file will be executed if rccmd is not able to connect one or more of the configured Upsman Upsicp servers asuming that either the host is down or the Upsman Upsicp process is not running Default is usr ups rccmd_notalive sh You may change this v
124. n of the shutdown sequence 88 JRCCMDCFG V4 0 2 0 Logfile Breene Control Execute at mail signal from RCCMD server fusr rcemd rcemd_mail sh edt Fi Execute at message signal from RCCMD server fusr rcomd recmd message sh Edit File Execute at execute signal from RCCMD server fusr rccmd rcemd execute sh Edit File Execute at shutdown signal from RCCMD server fuse rcemd rcemd_shutdown sh Save Cancel Figure 115 RCCMD Shutdown sh Tag the RCCMD shutdown relay into the Available Commands window and click the gt button to add this function into the Current Sequence File usr rccmd rccmd shutdown sh Available Commands RCCMD shut down relay Restart System Current Sequence RCCMD shut down relay to gx56 ssl RCCMD shut down relay to 111 111 111 1 RCCMD shut down relay to 111 111 111 1 RCCMD shut down relay to 111 111 111 1 RCCMD shut down relay to 111 111 111 1 RCCMD shut down relay to 111 111 111 1 RCCMD shut down relay to 111 111 111 1 DI Wait 5 seconds usr recmd rcemd message sh Parameter Shut down System Add custom application Description of Shut down System Ends your session and shuts down System so that you can safely turn off computer Save Cancel Figure 116 RCCMD Shutdown Sequence The following panel will appear in which you can enter the desired IP address range or hostname 89 RCCMD Configurat
125. n the console or a terminal or a terminal emulation under the X Window System e g xterm Note The contents of rccmd cfg are vital to system security It should be writeable only for the System User root Run rccmd conf SU Password 90 cd usr ups rccmd_conf if rccmd cfg does not exist e g if you run rccmd conf for the first time the following notice will be displayed ME generex host usr ups File not found usr ups recnd cfg does not exist create it Exit Figure 118 Making the Configuration File To proceed hit the Tab key until the Create button it is highlighted and press Enter otherwise select Exit If you created rccmd cfg or if the file existed already rccmd conf will switch to its main configuration menu generex host usr ups Recad Configuration Recmd Network Options i Access Control List Figure 119 RCCMD Configuration Menu UNIX To switch between the menu entries use the Tab key and or the arrow keys lt gt 1 and To select an entry press Enter It is not necessary to work from top to the bottom you may configure the menu items in any order In fact it is not necessary to configure anything at all if you just select save rccmd cfg will be written with default values sufficient to run rccmd To use all features of rccmd and or improve security it is however strongly suggested to customize rccmd cfg Configure Rccmd
126. ndancy management functionality as follows 145 Every UPS must be equipped with a CS121 or UPSMAN software computer When ticking the box use RCCMD group redundancy you are guided to a menue where you can choose which CS121 UPSMAN are supplying this RCCMD client E g if 4 CS121 UPSMAN are installed into 4 UPS than each may send a shutdown signal to this RCCMD client DCC gt anfouratiorn Addresses Functions Logfile Execute Control Max logfile size Kb View Logfile IRCCMDCFG V4 0 0 11 Ce Figure 195 RCCMD Configuration Window Logfile You can configure the log file size and edit the executing bat files in this installation window Addresses Functions Logfile Execute Control _ OE Execute at mail signal from RCCMD server fusr reemd recmd_miail sh ee Execute at message signal from RCCMD server fusr rccmd rccmd message sh Edit File Execute at execute signal from RCCMD server fusr reemd recmd_execute sh Edit File Execute at shutdown signal from RCCMD server Jusr rccmd recmd shutdown sh IECCMDEFG V4 0 0 11 Figure 196 RCCMD ConfigurationW indow Execute 146 If you click the Configure button you will be able to enter the mail settings and to use the mail function of RCCMD AAA RCCMD Configuration Addresses Functions Logfile Execute Control ee Execute at mail signal from RCCMD
127. nds your session and shuts down Windows so that you can safely turn off the power The default shutdown bat content is as follows rem created by setup echo off set path C WINDOWS C WINDOWS system32 C Program Files RCCMD ExitWin exe shutdown force Qcls 2 13 1 RCCMD Client as Relay Station In order to reach a bigger number of RCCMD receivers one RCCMD client needs to be operated as relay station The receiver will be configured so that it will receive a RCCMD signal and this signal will be used to start a batch file which then starts even more RCCMD sender signals This workstation is then sender and receiver at the same time and is therefore an important link in the UPS monitoring chain Generally the usage of a RCCMD client as a relay station makes the management of several 100 RCCMD clients far easier than configuring this via the Web interface of the CS121 Additionally all Web browser event configurations have a certain limitation so that it is required to use the relay function if the number of jobs exceed 50 per event at the CS121 HW 131 at older CS121 adapters even earlier See the following script which lets the RCCMD client act as relay station 51 Figure 64 Example Batch File RCCMD act as Relay Station start is a Windows batch command to start the program call in several instances This allows to execute programs simoultanously and speeds up the shutdown process Please note that start is not s
128. nectionis Use RCCMD Traps Polling rate 30 Connect retries 100 a E Execute at failure UPS ee C Program Files RCCMD alive bat UPSMAH RCCMD Redundancy Audible settings Use RCCMD group redundancy O Beep off gt Beep endless Beep 5 times 1 to 9 RCCMD ver 4 0 1 7 Figure 56 UPSMAN Alive Checking Redundancy Window 45 Step 6 If you want to use the UPSMAN alive checking recommended check the Enable connection check box Alive check is a signal send out to the UPSMAN or CS121 on port 5769 to check if the UPSMAN has still UPS data or not If this fails the scriptfile alive bat will be executed which causes a messagbox coming up The polling rate default 30 min defines the polling of the UPSMAN service connect retries default 5 means after 5 unsuccessful connection tries an alarm will be triggered The function Use RCCMD Traps enables UPSMAN RCCMD UNMS traps which show the UPS status as a trap message If activated it will display a local message when the UPS status of the UPSMAN RCCMD server changes If you click the Test connection s button the UPSMAN alive checking of the entered IP addresses will start port 5769 will be tested You can define the Audible Settings as follows Beep off Beep endless Beep amount 1 to 9 If you click the Browse button you will get a selection of the default batch files ag Client installation lo
129. nnnn 65 Figure 83 Console Installation OS Detection License Agreement rrrrrnnvvnnnnvvvvvvnvnvnnnn 66 Figure 84 Console Installation Features Selection rrrrrrrrrrrnnnnnrrrrrnnrrnnnnnnnnrnnrrrrnnnnnnnnn 66 Figure 85 Console Installation RCCMD Autostart Weblf Protocol Port 00 67 Figure 86 Console Installation RCCMD Configuration required Firewall Exceptions 67 Figure 87 Console Installation RCCMD Start Installation Complete wwrrrrrrrrnnnnnnnnnne 68 Figure 88 RCCMD Weblnterface rrrrrrnnnnnnnanonnnnnnnnnrrrvnnnnrrrrnnnnnnnnnnnnnnnnnnnnnnnnessssnnnnnnnnnnnnnnn 68 Figure 89 RCCMD Weblnterface Connections rrrrrrnrnrrrnanrrnnnnnnnnnnnnrrvvnnnneersrnnnnrnnnnnnnnnn 69 Figure 90 RCCMD Weblnterface Heartbeats rrnnrrrrnnnnnnnnnnnrrrnnnnnnnnnrrrrnnnnnnerrrnrrrrnnnnnnnnnn 70 Figure 91 RCCMD Weblnterface Redundancy urnnnnnvrrnnnnnnnnnnvrnnnnnnnnnrnnrrrnnnnnernnrrrnnenternn 71 Figure 92 RCCMD Weblnterface Shutdown SettingS rrrrrrrnnnnnrrrrrvvrrrrnnrennnnnnnnnnnnnnnnnn 72 Figure 93 RCCMD Weblnterface Notification Settings rrrrrrrrrrrrrrrrvrrrrrrrrrrrrrrrrrnvnnnenn 72 167 Figure 94 RCCMD Weblnterface Advanced Settings rrrrrrrrnnnnnrrrrrnnnvnnnnvnrnrnrrrrnnnnnnnnnn 73 Figure 95 RCCMD Weblnterface Web ACCESS rrnrrrrnnnnnrnnnnnvrrnnnnnnnnnnrrrnnnennennrnerrrnnnnnnnnnn 73 Figure 96 RCCMD Weblnterface Event Log rrrnnn
130. nnnvrrnnnnnrrnnnrrnnnn 136 Figure 181 RCCMD Weblnterface Heartbeats rrrnnrrrrrnnnnvnnnnrnrrrnnrrnrnnnnrrrrnnnnnererrrrrrrrnnn 137 Figure 182 ROCMD Weblnterface Redundancy rnnrnnnnrnnnnnnnnnnnrrnnnnnnnnrnnnnrnnnnnnrrnnnrnnnnn 138 Figure 183 RCCMD WeblInterface Shutdown Settings rrrrrnnrnnrrrnnnnnnrrrrrnnnnnnnnrrrrrrrnnn 139 Figure 184 RCCMD W ebinterface Notification Settings rrrvrrnrnnnnvrnnnrrnvrnernrnvrnnrrennne 139 Figure 185 RCCMD W ebinterface Advanced Settings rrrnnnnnnnnvrrnnnnnnnnnnvrnnnnnnrrnnnrrnnnn 140 Figure 186 RCCMD Weblnterface Web ACCESS mmnnrrrnnvrnnnnnnrrnnvrrnnnnnnrrnnnnvrrnnnnrrrnnnrrnnen 140 Figure 187 RCCMD Weblnterface Event Log rrrrnrrrrrvrrvrrvvrvrrrrrrvvrvrnvrrrrvrrrrvrrrnnnrrnnnnnnn 141 Figure 188 RCCMD Weblnterface System StatusS rrrrrnrrrrrrrrrrrrrrrrrrnnnrnvrrnvrrrrnnnnnnnnnnn 141 Figure 189 RCCMD Weblnterface Help cccccccccccccceceeesseeeeseeaeseeeaeeeeeaaeaaaaaeaeaaaaaaaees 142 Figure 191 RCCMD IP Address Window cccccccccsscessseceecsneeeesseeeesseeeseseeeesteeessseeeeesaes 143 Figure 192 RCCMD Configuration Window Functions rrrrrrnrrnnnnnrrnnvrnnnnrennrrnnnnnnrrnnnnn 144 Figure 193 RCCMD Check UPSMAN Connections rrrnnnrnnnrrrrvnnnrvnnerrnrrrrnnrrnnnrrrrrrnnrnnnenn 145 Figure 194 ROCMD Redundancy ccsscccccsssssessssssscensssceceeseeessesssssssessseeesseaeeeensesesess 145 170
131. nnrvvvvvvnrnnnvnnnrnnnrnnnnnnnrnvennnnnnnennnnrnnnnnnnnnee 74 Figure 97 RCCMD Weblnterface System StatusS rrrnnnnrnrnrrrrnnnnnrrrrnrrrnnnnnnrnnnrnrrrnnnnnnnnnn 74 Figure 98 RCCMD Weblnterface Help mrrrrrvvrrrrrrrrvrrvrrrrrnnvnnvvrrrrrvrrrrrrerrrrnrsnrnnnnnnnnnsnnnnnnr 75 Figure 100 CS121 Configuration WAKEUP Comma rnnnrnrnnvvvvnnnnnrnnnnnnnnrrrrrrrernnnnrnnnnn 76 Figure 101 UPSMAN Configuration WAKEUP Command rvvrvvvvvvvvvvvvvvvvvvvvvvrnvervnnnnnnenn 77 Figure 103 AGCGMD SSL SENGS Leiknes 78 Figure 104 Timeserver SettingS ccccccccccccccccccccsscccccececcceeceeeeeeeeeeeeeeeesuaaasaaaeaaaeanaaeasaeaaaas 78 Figure 105 Settings Confirmation cccccccccccccccccececcccccccceeceeceeceeeeceeeeeeeseeeaeesseeeaeeeaneeaeees 79 Foure 1906 SSLE MI GUAM cass osteo ety sealer pea dea Senza toute hawt ta ecg eA h 79 Figure 107 Configuration RCCMD Sender IP Address rrrrrrrrrrnnnnnnnnrrvvvnnrrrrrnnnnnnnnnnnnnnnnn 83 Figure 108 Configuration RCCMD Functions rrrrnnrnnvnrrvrrrrrrrrrrrrnvvrrrrvrrrvrrrrrrrrrrnrrnnnnnnnen 84 Figure 109 Configuration RCCMD Redundancy rrrrrrrnnrrnnnnnnnnnnnnnrrnnrrrvnnnnerrrnrnrernnnnnnnnnn 85 Figure 110 Configuration RCCMD Log File rrnnnnnnrrrrvvvvrrrrnnnnnnnnnnnnnnnnrrvvnnnnrrrrnnnnnnnnnnnnnnnn 85 Figure 111 Configuration RCCMD Execute rrrnnnnnnrvvvvvvnnrrnnnnnrnnrrnnnnnnnrvnnnnnnnennnnnnnnnnnnnnnnee 86 Figure 112 Configuration R
132. nstallation Language Selection Introduction Enter your license key and note the license agreement Enter your license key Usually the license key is located on the installation booklet or on a label on the reverse side of the CD sleeve Enter license key 12SHARK3 23456789 Test version Only meant for testing purposes key only valid for 3 days Would you like to enter a different license key Yes No gt No Installation and Use of RCCMD Requires Acceptance of the Following License Agreement Copyright The information contained in the manual of this product is nonconditional and may be changed without due notice GENEREX nor the reseller of this product undertakes no obligations with this information The software described in this brochure is given on the basis of a license contract and an obligation to secrecy Ci e an obligation not to further publicise the software material gt The purchaser may make a single copy of the software material for backup purposes No parts of this manual may be transfered to third persons either electronically or mechanically or by photocopies or similar means without the express written permisson of the GENEREX or the royalty holder The UPSMAN management software includes for every serialnumber the licence for using the UPS service at one server with one UPS The UPSMON JAVAMON Webinterf ace is freeware and may be copied and used from an unlimited numbers of connected workstati
133. ock now Figure 38 Timeserver Settings Click the Save Configuration button and the Save Exit amp Reboot button to confirm your settings 31 C 121 Configuration Manager D Reset to Factory Settings Load the CS121 factory settings into the configuration editor p Cancel Recent Changes Reset all changes and reload the saved settings Save Configuration Write all changes to flash memory Changes will be used after the next reboot Backup Configuration Store a backup of the configuration on your local harddisk Use right mousebutton and save target as NOTE For UPLOAD older config files to new firmware versions please contact suppor Reboot Reboot the C8121 without saving configuration changes Gi Save Exit amp Reboot Write all changes to flash memory and reboot the C9121 Please be patient after clicking here Figure 39 Settings Confirmation Start the RCCMD Web Configurator again and enable the SSL network feature i x a http localhost 8080 Options connections htm Datei Bearbeiten Ansicht Favoriten Extras gly Favoriten 33 Web Slice Katalog v pene 0 0 0 0 0 0 0 1 Connections v Options The list below identifies all senders that are allowed to connect to this listener Note An empty list means that every sender can connect to this listener Connections Redundan 192 168 222 113 Shutdown Settings Notification Settings Advanced Settings Web Confiquration
134. of RCCMD into the following chapters 4 1 RCCMD on VMware ESX The RCCMD Software for VMWare ESX Server is a Linux based TCP client for receiving shutdown calls from UPSMAN software any vendor CS121 any vendor or other RCCMD licensed applications like SNMP adapters etc from other vendors RCCMD for ESX Server runs on GNU Linux 2 6 18 or higher which is the basis of the 2008 ESX 3 5 x Serverplatform For installing RCCMD please refer to chapter 4 RCCMD for UNIX following we describe some special aspects which are only applicable to ESX Server Installation Since the ESX Server does not offer any graphical interface the download of RCCMD client for ESX Server from the GENEREX Website or other sites is not easy unless you have extra tools installed like commandline browsers like W get 103 Additionally by default there is no FTP server active on ESX Server so a transfer of a downloaded RCCMD package may be blocked For this reason we recommend to use a local interface on your ESX Server like CD ROM Driver or USB stick Download RCCMD for ESX Server from the GENEREX Website using your original RCCMD licensekey not older than 2 years and extract the TAR file Copy the files on a CD R and insert this CD now into your ESX Server CD drive Alternativly use UPSMAN CD ROM Version 5 48 or higher Login as root and mount the CD ROM on the VMware ESX Server Enter mount dev cdrom Change to the CD ROM by c
135. of the installation e normal installation fy normal operation of RCCMD 55 lt ENTER gt T Figure 150 Warning License Check Automatic firewall configuration s Attention Not required for VMware ESXi 5 because this version will be delivered without firewall RCCMD is using the port 6003 TCP and UDP for incoming IP packages At the usage of the Check Alive function the port 5769 will be automatically enabled during installation too The installer will open these ports automatically on the vMA 4 x Port 6003 was opened for tep and udp protocols Port 5769 was pened for tep protocol PRESS lt ENTER gt TO CONTINUE Figure 151 Installer announces firewall ports opened Note the firewall exceptions Figure 152 Firewall Exceptions 115 4 2 4 RCCMD Weblnterface from Version 4 2 0 0 RCCMD provides its own web interface from version 4 2 0 0 or higher Therefore it is possible to configure and control RCCMD remotely Please note that the firewall port 8443 TCP must be enabled Enter the following into your web browser to get remote access to the vMA where RCCMD is running https IP address of the vMA 8443 amp https 192 168 200 103 8443 login htn C E Google RCCMD IP 192 168 200 103 System Login System Status Current status of RCCMD is running Username admin Password Login Figure 153 RCCMD Weblnterface You can enter the IP addresses of the allowed RCCMD
136. ogram job start failed The error message job start failed appears if the user got no rights for the execution of the rccmd shutdown sh Solution 1 Arrange the X right on the rccmd shutdown sh as follows CHMOD x rocmd shutdown sh Solution 2 If the accordant rights are at present the user did enter the wrong login data for the physical ESXi server You can adjust these data into the file esxi_creds in the folder usr rccmd Problem You get the following message after the start of the installation on a vMA on an ESXi server 159 192 168 200 94 Pu Figure 203 Error Message Unlicensed Version Solution It is required that the OS contains a TMP folder tmp to execute a successful RCCMD installation Appendix A OpenSSL This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http www openssl org B Syntax for the switching of the outputs Set the RCCMD client at port 6002 to on define the CS121 AUX ports as outputs and restart the CS121 Install the RCCMD Windows Wizard and open a DOS box The following is a syntax example with the IP address 192 168 202 165 C Program Files RCCMD reend se EXECUTE AUX I L a 192 166 202 165 p 6002 ATTENTION The blank after the Execute is important Common syntax for the switching of AUX ports AUX 1 0 Porti set to low AUX 1 1 Porti set to high AUX 2 0 Port2 set to low AUX 2 1 Port2
137. ollowing functions 87 BY RCCMD Configuration Logfile Execute Control Control the Rccmd 3 Stop Recmd r O snema UPS UPSMAN c 3 IR CCMDCFES V4 0 0 11 Figure 114 Configuration RCCMD Control 3 9 1 RCCMD Client as Relay Station If you need to reach a bigger amount of receivers it is required to define the CS121 as relay station The receiver must be defined if receiving a RCCMD signal that it will start a script which will send further RCCMD signals The workstation is receiver and sender at the same time and thus an important connection in the UPS monitoring The usage of a RCCMD client as relay station makes the monitoring of more than hundred RCCMD clients as easier as the configuration of the CS121 via web browser Furthermore the web browser event configuration got a limit so that it is required to use the relay function if the amount of jobs is more than 50 per event at the CS121 The following steps are required for the configuration of the relay function e Open the file recmd_shutdown sh with an editor e Add prior of the shutdown of the workstation shutdown h now the relay calls e g the call of the included send shutdown sh e Add the desired IP addresses or rather the DNS names Send shutdown sh a 10 10 10 10 a 10s10 10 11 a 10 10s10 12 e Save the settings of the rccmd shutdown sh The RCCMD version 4 0 2 0 provides a grafical configuratio
138. on you can disable the Start Jobs as interactive user feature that means if disabled that RCCMD will execute jobs if nobody is logged in on the system DOG Advanced Settings Mozilla Firefox File Edit View History Bookmarks Tools Help oa v S 8 htip nocalhost 8080 Options advancedsettings htm v fv Goog a Most Visited v Getting Started Latest Headlines v 6 Advanced Settings ap v 0 0 0 0 0 0 0 1 v Options When the event log file reaches the size below then older entries will be deleted Maximum file size KB 200 Connections Heartbeats Redundancy Shutdown Settings RCCMD Bindings e Notification Settings e Advanced Settings The information below defines IP address and TCP port of the RCCMD Listener Web Configuration IP address 0 0 0 0 means all addresses 0 0 0 0 6003 Note IP address 0 0 0 0 means every local address default TCP Port is 6003 Done Figure 164 RCCMD Weblnterface Advanced Settings Click the Save Changes button prior of the leaving of this site to save your changes You can change the default password for the user admin into the menu Web Configuration In addition you can disable the HTTPS protocol if you just want to use the HTTP protocol The RCCMD version 4 2 3 0 or higher provides the feature of changing the default ports for HTTP and HTTPS 124 Advanced Settings Mozilla Firefox File Edit View Hi
139. onal license keys are available from your UPS dealer whereas the CD can be used again for the actual installation 151 recmd nim Modul for the multiserver shutdown in IP networks The rccmd nim contains different command line parameters which are either for the send or listen modul of the RCCMD modul rccmd Help rccmd s Sending off a ping signal to a waiting program rccmd Waiting for a ping signal A command can be executed after the reception of the ping signal rccmd p Setting the port address default 6003 rccmd a Address in IP format e g 192 168 202 1 rccmd t Time in seconds until a connection will be established default timeout 10 Example load sys ups rccmd nlm s a 192 168 202 1 a 192 168 202 1 load sys ups rccmd nIm s a 192 168 202 1 t 10 load sys ups rccmd nlm I a 192 168 202 1 shutcmd nim para rccmdipx nim This is a modul for just IPX networks This modul sends a shutdown command or any other console command directly to every IPX server name Please start RCCMDIPX on all Novell consols The modul needs to be loaded on both servers This modul has to loaded on both servers first 1 Rename RCCMDIPX to RCCMS NLM 2 Load RCCMD The following syntax is valid rccmd lt server name gt lt console command gt Whereas lt server name gt is a valid server in a network enviroment and lt console command gt a valid NetWare command is Example 1 load sy
140. ons The RCCMD client software requires a separate license key for every installation Unless a RCCMD enterprise license is available the user must NOT install PRESS lt ENTER gt TO CONTINUE Figure 15 RCCMD Console Installation License Key License Agreement Select the desired product features enter an install folder and note the firewall exceptions 17 ENTER A GOMMA SEPARATED LIST OF NUMBERS REPRESENTING THE FEATURES YOU WOULD LIKE TO SELECT OR DESELEGT TO VIEW A FEATURE S DESCRIPTION ENTER lt NUMBER gt PRESS lt RETURN gt WHEN YOU ARE DONE i X RCCMD 2 X Weblf Please choose the Features to be installed by this installer Where would you like to install Default Install Folder C Program Files RCCMD ENTER AN ABSOLUTE PATH OR PRESS lt ENTER gt TO ACCEPT THE DEFAULT irewall Exceptions will be added for RCCMDWebl f PRESS lt ENTER gt TO CONTINUE Figure 16 RCCMD Console Installation Features Selection Install Folder Firewall Exceptions Select a link location and note the pre installation summary Where would you like to create links gt 1 Default C ProgramData Microsoft Windows Start MenunPrograms RGGMD 2 In your home folder 3 Choose another location 4 Don t create links ENTER THE NUMBER OF AN OPTION ABOVE OR PRESS lt ENTER gt TO ACCEPT THE DEFAULT Pre Installation Summary Please Review the Following Before Continuing Product Name RCCMD
141. op This account Administrator Browse Password le eee Confirm password eoees You can enable or disable this service for the hardware profiles listed below Hardware Profile Service Undocked Profile Enabled Docked Profile Enabled Enable Disable Cancel Apply Figure 47 Administrator Password Confirmation Services Ay The account drinistrator has been granted the Log On As 4 Service right Figure 47 Service Right Info Window 2 8 Testing of the Shutdown Bat File We recommend to test the edited shutdown bat file The shutdown program EXITWIN EXE is predefined Just enter Exitwin exe inthe RCCMD directory for syntax help for this shutdown tool You may use also your own shutdown tool or any other which we provide with this software GP ATTENTION If your configuration works fine in the DEBUG mode does not necessaryly mean that it works also with the RCCMD as NT service Please ensure that the RCCMD as service has been started in a user account with administrative rights otherwise it may happen that only non restrictive programs may be executed like notepad exe but no Shutdown This will result in the NT error message Adjust Token Privileges failed If a program has in fact started or not can be seen in Taskmanager window ALT CTRL DEL because a service does not a started program in the current user session due to non interactive transaction with the desktop The full command s
142. ote Command Program 2012 10 17 15 27 12 RCCMD RcvThreadUdp gestartet 2012 10 17 15 39 24 RCCMD RCCMD Sender 192 168 222 75 hat keine Berechtigung dieses Programm zu starten Pr fen Sie RCCMD Berechtigungsliste 2012 10 17 15 39 24 RCCMD RCCMD message received from 192 168 222 75 2012 10 17 15 40 22 RCCMD RCCMD Listen Mode stopped 2012 10 17 15 40 22 RCCMD RcvThreadUdp angehalten 2012 10 17 15 40 25 RCCMD Copyright c 1996 2012 Generex GmbH Reload Log File Figure 29 RCCMD Weblnterface Configurator View Event Log You can check the current status of RCCMD into the menu Status System Status update the status and restart or rather stop start the RCCMD service 26 E http lecelhost 3080 Ratus systern Status ht Datei Bearbeiten Ansicht Favoriten Extras Wy Favoriten yy Web Slice Katalog Systern Status 127 0 0 1 Status System Status View Event Log Current status of RCCMD is running System Status Figure 30 RCCMD Weblnterface Configurator System Status You can open the RCCMD user manual into the menu Help ad you can follow the link to www generex de amp i http localhost 8080 Help manuals htm Datei Bearbeiten Ansicht Favoriten Extras she Favoriten 2 E Web Slice Katalog v e Tae ost Help RCCMD Manual Find more documentation online here Figure 31 RCCMD Weblnterface Configurator Help 2
143. output output output output output output output output output output output for legal reasons Open Source 161 1 Om 1 I DADA Oa oO FSF BP WW NY DR toO to to EG LO to to EG EO to to toO to to EG low high low high low high low high low high low high low high low high Figure 204 pxout bat The command is called pxout bat and expect 4 parameters IP address or hostname of the Raritan device SNMP community string the one for write access Outlet number 1 to 12 0 off 1 on 2 The batch file pxout bat accepts now several parameters from incoming RCCMD executes and translates these into SNMP set commands for the Raritan The pxout bat accepts the following command syntax pxout bat lt IP address gt lt community gt lt Outlet gt lt on off gt e IP address This is the IP address of the Raritan e Community This is the community string for write access configured at the Raritan or SNMP set commands default is public Outlet This is the number of the Raritan Outlet 1 to 12 which you want to switch e On Off This is the signal you want to transmit where 0 is off and 1 is on Example pxout bat 192 168 200 11 public 0 This example will switch the Raritan with the IP address 192 168 200 11 the outlet 4 to off If this works manually from your Windows RCCMD computer than you can go ahead with
144. own duration for the virtual machines and the name of the vMA at is the Shutdown Duration Enter the amount Shutdown Duration a VMA name Figure 144 RCCMD Shutdown Duration vMA Name 4 2 3 2 RCCMD Installation with vCenter Select option 1 and enter the vCenter access data 112 will be required The vS ePlugin e Client for Windows RCCMD will then ENTER THE NUMBER FOR YOUR CHOICE Figure 145 RCCMD vCenter Access Data Note The vMA and the ESXi server will be shut downed at the same time This behaviour is not critical for a RCCMD vMA If vMotion is active on the vCenter server the vMA will be moved on another ESXi server automatically the IP address and the functionality will be kept Note the pre installation summary Continuing PRESS lt ENTER gt TO CONT Figure 146 Pre Installation Summary 113 Set the Weblf port and enter a password for the RCCMD web interface the RCCMD WebIf lt ENTER gt TO ACCEPT THE DEFAULT for RCCMD Figure 147 RCCMD Weblf Protocol Password Note that a RCCMD configuration is required PRESS lt ENTER gt t RCCMD now start RCCMD from it manually use RCCMD now lt ENTER gt TO ACCEPT THE Figure 148 Configuration Advice RCCMD Start 114 Figure 149 Conclusion During the installation RCCMD will check the compatibility of the ESXi host If the user details are incorrect you will get the following warning at the end
145. r se aed iedhes 111 Figure 142 RCCMD Product Feature Selection mrrrrrrnrrrrrrrrrrnnnrnrrnnrrrrrrnnrrrnerrrrrrnnnnnnen 111 Figure 143 RCCMD vCenter Selection ESXi Access Data rrrrrrnnrnnnnnnnnrrnnnnnnnnnnnnnnnnnre 112 Figure 151 Installer announces firewall ports opened rrrrrrrrrrnnnnnnnrrrrrrrrvrrrnnnnnnnrrrrrerenn 115 Figure 153 ROCMD Weblnterface rnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnennnnnnnennnnrnnnnnnnnrnenrnnennnnensessesennnn 116 Figure 154 RCCMD Weblnterface Connections rrrrrrnnnnnnnnnnnnernnnnnrrnnnnrrrrrnnnnrerrrrrrrrrnnn 117 Figure 155 RCCMD Weblnterface Heartbeats mmrrrrrnnvrrnnnnnrnnnvrrnrnnnnnnnnnnrrnnnnnnrrnnnrrnnnn 118 Figure 156 RCCMD Weblnterface Redundancy mmnnnnnnvrnnnnnnrnnnvrrnnnnnnnnnnnvrrnnnenrrnnnrrnnnn 119 Figure 157 RCCMD WeblInterface Shutdown Settings rrrrrnnnnnrrrnnnnnnrrrrrnnnnnrnnrnrrrrrnnn 120 Figure 158 RCCMD Weblnterface Notification Settings rrrnvrrnrnvnnvrnrnnnnvrnnrnrnrnnnrennne 120 Figure 159 RCCMD Weblinterface Remote Access vMA Shutdown Settings 121 Figure 160 RCCMD WeblInterface Remote Access VMware Settings ee 121 Figure 161 RCCMD W ebinterface VMware Settings VMA Name nnnnnnnnnnnnnnnnnnnnnnnnnn 122 169 Figure 164 RCCMD Weblnterface Advanced Settings rrrrrrrrrrnrrnnnnnnnnrrrvrvnrrrrrrrnnnnnnnn 124 Figure 165 RCCMD Weblnterface Web ACCESS rrnnrrrrrrnnnrn
146. rder Virtual Machine Startup Startup Delay Shutdown Shutdown Delay Automatic Startup 1 2 Sphere Managem Enabled 10 seconds Shut do 30 seconds Move Up Any Order Move Down Manual Startup EEE dt DI OK Cancel Help Figure 135 vSphere Client Auto Start Configuration 107 2 Virtual Machine Autostart Settings Startup Settings After starting this virtual machine continue starting other virtual machines according to the Following settings Use default fe Use specified settings Startup Delay 10 seconds f Continue immediately if the VMware Tools start Shutdown Settings After stopping this virtual machine continue stopping other virtual machines according to the Following settings Use default fe Use specified settings Shutdown Delay 30 seconds Perform shutdown action Guest Shutdown met oo Figure 136 vSphere Client Auto Start Delay The vSphere client provides the following settings 1 Virtual Machine Startup System Settings I Allow virtual machines to start and stop automatically with the system Default Startup Delay Default Shutdown Delay For each virtual machine delay startup for For each virtual machine delay shutdown for 10 seconds 30 seconds IV Continue immediately if the VMware Tools start Shutdown Action Suspend x Z Power Off Startup Order Suspend Power on the specified virtu
147. ress 192 168 222 43 immediately Tip You should stop RCCMD running in the background on this Windows computer so you will better see whats going on Stop the RCCMD service than open a command line into the RCCMD folder and start rccmd exe debug Now the software will run in the foreground and you can watch the communication 4 The Raritan with firmware 1 4 1 is unfortunetaley buggy Here the workaround The default community strings for the Raritan are identically set for read and write to public but this configuration is invalid It must be different Solution Stop the SNMP Agent at the Raritan change the community for write to any other than public and restart it 163 gt S A 319216822243 https 192 168 222 43 home asp Raritan ca External Sensors Maintenance Outlet Groups Heip D PX PDU eer ominion ene Hen Home gt PDU Status DEN Line Loads SMTP Settings SNMP Settings Event Log Time amp Session 2000 01 23 02 05 User admin State 198 sec idle Your IP 192 168 200 41 Line 1 Last Login 2000 01 23 00 49 SNMP Settings L y heii inn gt Device Information Name Leiste Model PX DPXS12A 16 Name State Control RMS Current Active Power Group Member IP Address 192 168 222 43 Firmware 01 04 01 Qutlet1 on On off Cycle 0 00Amps 0 Watts no Firmware Status OK Outlet 2 off
148. ress Shutdown duration Verified Total estimated Shutdown time for the System with current configuration 00 01 30 192 168 200 30 vSphere Client Datei Bearbeiten Ansicht Bestandsliste Verwaltung Plug Ins Hilfe Gg a Home p gh Bestandsliste p f Bestandsliste su 6 0 A BBR Ow E 192 168 200 30 vMA55 ES E IPM 1 40 EB vCenter Server Appliance GQ vCenter wrong G vMA 5501 i VMA test E Erste Schritte Ubersicht Ressourcenzuteilung Leistung Ereignisse Konsole Berechtigungen Figure 161 RCCMD WeblInterface VMware Settings VMA Name If you want to add a physical host just click the Add Host button and enter the accordant parameters Connections x Connections gt amp 192 168 200 95 2080 Opt reSettingshin Our ee O GENEREX Team BY Download Windows myvatnsoraefi_t jpg CDMenue S Mercurial repositori GENEREX Home C Other bookmarks EEE EE seconds Options Connections Heartbeats Enter the information for this ESXi Host below Shutdown Settings ESXi Host IP 192 168 200 34 Notification Settings x z Web Configuration User name root The virtual machin Time granted for virtual machines to shutdown before Host gets machines and hos shutdown in seconds 117 192 168 200 30 Total estimated Shutdown time for the System wilh current configurator 00 01 57 Figure 162 RCCMD WeblInterface
149. rex or in any intellectual property right including without limitation any copyright patents relating to the Products shall remain the exclusive property of Generex Generex will undertake to deal promptly with any complaints about the content of this document Comments or complaints about the document should be addressed to Generex Systems GmbH Copyright of the European Union is effective Copyright EU Copyright c 1995 2014 GENEREX GmbH Hamburg Germany All rights reserved Revision 001 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 History First Release Added RCCMD on Citrix XEN Server RCCMD with SSL Update UNIX multiple sender configuration Added Alternative SSL configuration Added Syntax for switching outputs Added RCCMD Client as relay station Update Installation of RCCMD Update RCCMD InstallAnywhere Installation Added Silent Installation Windows Added Grafical RCCMD relay configuration Added Combined RCCMD Silent Installation and Configuration Added Silent Installation UNIX Added Console Installation UNIX Added RCCMD on ESXi Server 4 x Added Know How Pool Added Automatic Reset of the Redundancy Alarm Added Grafical RCCMD telay configuration UNIX MAC Added Configuration on Windows 2008 Server Core x64 Added RCCMD FAQ Added RCCMD on ESXi 4 1 with vMA 4 1 Added RCCMD
150. rrnnnrrrnnnnrrnnnnrrrrrnneenerrrrrrrrrnnn 125 Figure 166 RCCMD Weblnterface Event Log rrrrvrvvvrrvvvrvvvrvrrvrrrvvrrrrvrvvrvrrrrrrrnrnnrnnnnnnnn 125 Figure 167 RCCMD Weblnterface System StatuS rrrnrrnnnnnnnnnnvrrnnnnnnnnnnnnrrrnnnnnrnnnnrnnnnn 126 Figure 169 Firewall Configuration nrrrrovnnnnnnnnnnnrnnnvnnnnrnnennnnnnnnnnnnrnnnnnnnnrnnnrnnenennneeeessnnnnnn 130 Figure 170 RCCMD Installation Welcome rrnrnnnnnnnnnnnrrnnnnnnnnnnnnnnnnnnrrrnnnnnrrrnnnnnneerrrrerrrnnn 131 Figure 171 ROCMD Enter Your License Key mrrnnvrnnnnnnnnnnnvvnnennnnnennnvnnnnrnnnnnnnennnennnennnennnn 131 Figure 172 RCCMD Choose Install Set rrrrrrrrnnrrrrrrrrrrrrrnnrvvrvvrvvvvrrrrrrrrrrsrsvrrvrrnrnnnnnnnnnne 132 Figure 173 RCCMD Choose Alias Folder ccccccccccccccccecnseeeeeeeeeeeeeeeeeeeeeeeaaeeeeeaeeaaaaaes 132 Figur 174 ROCGMD MOSSAQGS sjansene dd dd adel 133 Figure 175 RCCMD Pre Installation Overview rrrrnnnrrrrrrnvnvrvnvrnnrnnrrrrnnnnnrrrrrnnneneenerrerrrnnn 133 Figure 176 RGCMD Set Weblf ACCESS rrrnnrnnrnnnnnrrnnnnnnrrrnerrnnnnnnnnnnnnnrrrrnsnnnrrrnenenenersessennnnn 134 Figure 177 ROCMD Configuration required rrrrrrnnrrrrvrnrvrrrrvrrvrvnrvrrrrrrrrnrrrrnrrrrrnnnnnnnnnnnnn 134 Figure 178 ROCMD Install Complete rerrrnrrrnrnrnrnnnnnnnnrnnnrrnnnvnnnnnnnnnnrnnnnnnnnrvnenennnenensnennnnn 135 Fore T79RCCMD NINE ee 135 Figure 180 RCCMD Weblnterface Connections rrrrrnnrrrnnnnnrnnnvrrnnnnnnnnn
151. s RCCMD modules without registered license Prior of the installation you should verify that port 6003 is not in use Check this with the command netstat an Ensure that there is no other process running or start the RCCMD module at another port address with the option p for sending and receiving Ensure too that you will use this port for every command in the network Please follow the instructions of the next chapter carefully For further help you may use the user manual and the troubleshooting pages or contact your UPS software dealer GP Important The Alpha Version is linked to OpenVMS 7 1 For OpenVMS 6 x use the Version 6 x in the following CD directory ex DKA200 VMS ALPHA 6X Installation procedure 153 e Connect the workstation to the network e Login into the VMS System using SYSTEM login e Mount the CD ROM device if DKA200 is the device name of the CD ROM MOUNT OVERRIDE IDENT DKA200 UPS UPS This is a system specific command Use the VMS help pages for your system or ask the system operator if you do not know how to mount your input device e Start the VMS install procedure by SYS UPDATE VMSINSTAL e or SYS UPDATE VMSINSTAL lt device gt e e g SYSSUPDATE VMSINSTAL RCCMD DKA200 VMS ALPHA VMSINSTAL is an interactive script so just follow the installation instructions on the screen all instructions are aditionally listed in the following subjects 5 11 e Answer YES at the prompt
152. s gt 12 6071 243 776 bytes free C RCCMD gt RCCNF_NT EXE UPSMAN Mess C RCCMD gt Figure 52 RCCMD Configuration Please take a look into chapter 2 for the installation procedure and into chapter 2 12 the configuration of RCCMD 2 13 Older RCCMD Configuration D Attention In the following we are describing the RCCMD configuration of the Windows tool Rcenf nt exe which was delivered until 04 2012 All functions are equal to the newer RCCMD Webinterface version which is delivered since 05 2012 The detailed functions of RCCMD are user interface independent and will be described for the older RCCMD version 43 ACCHD 4 The world most successful Shutdown and Messaging Client for all operating systems and parallel redundant UPS and powersupplies with SSL This ACCMD wizzard configures your computer as an ACCMD client Before you start make sure that jou have enough RCCMD license keys for pour installations Every RCCMD client requires unique license key any invalid or double used ROCMD keys will disable an ACCMD process Don t uze ACCMD keycodes more than once Tou will be requested to enter IP adresses of valid RCCMD senders for this client RCCMD senders are UPSMAN software C5121 network managers or any ACCMD licensed SNMP manager from other vendors Specifiy which RCCMD sender is permitted to execute actions on your ACCMD client If you do not enter any IPhostname any ACCMD sender will have permission to e
153. s ups rccmdipx or load RCCMD if RCCMDIPX NLM is renamed to RCCMD NLM 2 rccmd gnw1 forcedown or 1 load sys ups rccmdipx 2 rccmd gnw1 sys ups down ncf Instead of the down command for older clib nim files the forcedown command maybe used 152 Multiple start RCCMD on Novell The multiple start RCCMD on Novell is relatively easy to manage Several RCCMD clients may be started with the following command line load rccmd nim I a load down ncf whereas the syntax goes as follows LOADING RCCMD NLM L LISTENER A IP adress of UPSMAN CS121 RCCMD SENDER COMMAND COMMAND TO BE EXECUTED Example LOAD RCCMD NLM L A 192 168 10 2 LOAD DOWN NCF In this scenario the down ncf file is executed which leads to an immediate shutdown of the client computer if the RCCMD call from the RCCMD server sender is received Other ncf or nim executables files may be executed too A group of 8 ncf example files can be found in the UPSMAN installation directory Please note that these example files ma have to be adjusted by user administrator according to the configuration of the system 8 RCCMD on DEC VMS The UPS Management Software CD contains the RCCMD software The VMS RCCMD installation can be done by following the UNIX installation instructions in this manual all of the steps are the same Note The VMS license is not part of the standard CD It is to be ordered separately It is not permitted to use the VMS version and it
154. se Key Entry Step 3 Please enter your license key an choose your corresponding Windows OS from the list The used license determines which module can be installed GP Attention If you enter a wrong license number at this stage the RCCMD client software will be set to a 30 day trial version Please contact your UPS dealer for the full correct license if it was not with the original CD ROM You need a special license key for your RCCMD software You can identify the key with the RX3 in the first part of the license key Most of the times you need to order the key separately Introduction Agreement icut Folder ation Surirm ry Installing Install Corriplate InstallAnywhere by Macrovision License Agreement Installation and Use of RCCMD Requires Acceptance of the Following License Agreement Copyright The information contained in the manual of this product is nonconditional and may be changed without due notice GENEREX nor the reseller of this product undertakes no obligations with this information The software described in this brochure is given on the basis of a license contract and an obligation to secrecy i e an obligation vi Figure 4 License Agreement Select the feature you want to install Install Set Typical Z RCCMD Z Web f 4 Description This installs the application feature Figure 5 Choose Install Set Read and confirm the licen
155. se agreement and continue with the NEXT button Where Would You Like to Install Restore Default Folder Cancel Figure 6 Install Folder Selection In the next window enter the path where you want to install the software Default is the subdirectory RCCMD into the program files folder onto the hard disk C Attention If you want to execute a program or a batch file with RCCMD it is required that this program or batch file is located into the RCCMD installation folder RCCMD Not into Program files RCCMD like default or a search path is set on the folder It will be signalized Into the next window that firewall exceptions will be created for the RCCMD exe 6003 5769 TCP the RCCMDTray exe 971 TCP and the RCCMD Weblf 8080 TCP Windows Firewall Ausnahmen werden erzeugt f r RCCMD RCCMDTray RCCMD Weblf Figure 7 Firewall Exceptions The RCCMD tray provides the appearance of the RCCMD message box as pop up into the foreground If you do not want to receive messages from the RCCMD please close the RCCMD tray via the context menu To disable the RCCMD tray permanently you can disable it into the RCCMD configuration The RCCMD tray appears into the taskbar The red point means that the RCCMD service is not started or rather a problem has occured powerfailure communication lost Green means that the UPS status is okay RCCMD Tray 12 45 T E l 10 06 2011 Figure 8 RCCMD
156. server fusr recmd recmd mail sh ee E Mail Configuration Use E Mail E Mail address of the sender Name of the mail server SMTP Authentification C Use SMTP Authentification Login Password Figure 197 RCCMD E Mail Configuration The RCCMD version 4 0 2 0 provides a grafical configuration of the shutdown sequence Addresses Functions Logfile Execute Control Execute at mail signal from RCCMD server usr rccmd rccmd mail sh Configure Edit File Execute at message signal from RCCMD server usr rccmd rccmd_message sh Edit File Execute at execute signal from RCCMD server Jusr rccmd rccmd_execute sh Edit File Execute at shutdown signal from RCCMD server Jusr recmd rccmd_shutdown sh Browse Edit File IRCCMDCFG V4 0 2 0 ed Figure 198 Configuration RCCMD Execute 147 Click the Configure button to enter the shutdown sequence settings File usr rccmd rccmd shutdown sh Available Commands RCCMD shutdown relay Wait seconds Restart System Description of Shut down System The following commands are available Current Sequence IRCCMD shut down RCCMD shut down RCCMD shut down RCCMD shut down RCCMD shut down RCCMD shut down RCCMD shut down Wait 5 seconds fusr recmd rocemd_ Shut down System relay to gx56 ssl relay to 111 111 111 1 relay to 111 111 111 1 relay to 111 111 111 1 relay to
157. server address 1 to 0 0 0 0 Some public timeservers could be used for both protocols 129 6 15 29 National Institute of Standards and Technology 192 53 103 103 Physikalisch Technische Bundesanstalt Current system time Thu Dec 4 23 49 26 2008 imeserver Address 1 192 53 103 103 SNTP v Timeserver Address 2 0 0 0 0 SNTP v Timeserver Address 3 0 0 0 0 SNTP v Timezone GMT 01 00 Amsterdam Berlin Bern Rome Stockholm Vienna v Automatically adjust clock for daylight p changes implemented for european timezones only Connection Retries 2 Synchronize Time on incoming RAS connection Synchronize Time on outgoing RAS connection Test Timeserver 1 Test Timeserver 2 Test Timeserver 3 Synchronize CS 121 clock now Figure 104 Timeserver Settings Click the Save Configuration button and the Save Exit amp Reboot button to confirm your settings 78 C3121 Configuration Manager Reset to Factory Settings Load the C8121 factory settings into the configuration editor Cancel Recent Changes Reset all changes and reload the saved settings Save Configuration Write all changes to flash memory Changes will be used after the next reboot Backup Configuration Store a backup ofthe configuration on your local harddisk Use right mousebutton and save target as NOTE For UPLOAD older config files to new firmware versions please contact support Reboot Rebootthe C3121 without saving conf
158. story Bookmarks Tools Help NE A http localhost 8080 Options weblfManagement htm Fj Most Visitedv 6 Centos DSupportv Web Access v Options The information below is used to log on to this user interface Administrator User Name Connections Current Administrator Password Heartbeats New Administrator Password Redundanc Paano Hint e Shutdown Settings Select the access protocol for this user interface Notification Settings Protocol Advanced Settings Web Configuration e Logout Note Changes in protocol will become active upon the next start up Port for http pon er mps Restart RCCMD Weblf 127 0 0 1 gx HTTP No Security Figure 165 RCCMD W ebinterface Web Access Cancel Save Changes Click the Save Changes button prior of the leaving of this site to save your changes You can see the logging of the events into the menu Status Event Log DOG RCCMD Configurator Mozilla Firefox lt v e A http localhost 8080 Status viewEventLog htm v fv Google Most Visitedv Getting Started Latest Headlines v 6 RCCMD Configurator oF 0 0 0 0 0 0 0 1 Y Status Event Log e View Event Log These are the events that have occured on this computer 2012 10 18 15 23 22 rccmd 03915 Copyright c GENEREX GmbH 1996 2010 All rights reserved 2012 10 18 15 23 22 rccmd 03915 UPSMAN RCCM
159. t File button EF http localhost 8080 Options notificationSettings htm Extras Datei Bearbeite Ansicht Favoriten iy Favoriten a Web Slice Katalog v 127 0 0 1 Saas us E Mail Notification E Notification Settings v Options When RCCMD receives an e mail signal it will use the following setting Run this command file a Hea a rn Redundancy Shutdown Settings Notification Settings Advanced Settings Message Notification Web Configuration When RCCMD receives a message signal it will use the following setting Run this command file C Program FilesiRCCMDImessage bat Execute Notification When RCCMD receives an execute notification it will use the following setting Run this command file C Program Files RCCMD execute bat Figure 26 RCCMD Webinterface Configurator Notification Settings Click the Save Changes button prior of the leaving of this site to save your changes 24 You can define the maximum size of the event logfile into the menu Advanced Settings where the overwriting of older entries will start the RCCMD bindings for the IP address the RCCMD listener TCP port and the RCCMD Tray Message Port which will be used for the RCCMD messages In addition you can enable the Start Jobs as interactive user feature that means if disabled that RCCMD will execute jobs only if somebody is logged in on the system and the RCCMD Tray is active
160. t IP address gt alive There is no message if the UPSMAN is inactive Use this command to get help C Program FilesXNRCCMD gt rcemd a Bid be Microsoft Windows KP Version 5 1 2600 C Copyright 1985 2061 Microsoft Corp C RCCAD rccmd usage precmd paranm Pc init install service and set default parameters 1 install service u uninstall service y display version info name lt name gt use lt name gt instead of default RCCMD de hug start as a console app for debugging tlistenMode bs filepath set filepath for shutdown event ClistenMode gt ba filepath set filepath for upsmanWNotAlive event listenMode gt li IP Address hind listen socket on IP Address listenMode gt lt ATTENTION this will override registry settings a re start as a console app for sending mode 3C check upsman ssl use SSL connection ut use traps to check upsman in server mode or retrieve additional status info if in client mode cr connect retries for every check default 5 gt se command parameter l valid commands SHUTDOWN EXECUTE MEG ID MSG_TEXT MAIL ID MAIL TEST LOG ID LOG TEST WAKEUP a 192 14 206 99 a 192 168 268 981 Cmax 15 gt ac ac upsman adress max 15 gt plrl portaddr recmd Cdefault 66835 pc portaddr check upsman default 5S769 gt t r timeout recnd default 18 sec tE timeintervall check upsman Cdefault 3H Min rE max retries for check upsman tdefault
161. talled and configured to execute C ups shutdown bat 2 12 RCCMD for Windows 2008 Server Core x64 The configuration of the RCCMD Software on Windows 2008 Server Core x64 got one specific It is required to start the RCCMD configuration out of the default folder C RCCMD with the following command C RCCMD gt RCCNF_ NT EXE RCCMD 4 Shutdown and Messaging Client for all operating systems and parallel redundant UPS and powersupplies with SSL This RCCMD wizzard configures pour computer as an RCCMD client Before you start make sure that you have enough RCCMD license keys for your installations E very RCCMD client requires a unique license key any invalid or double RCCMD key will disable an RCCMD process Don t use RCCMD keycodes more than once I Following you will be requested to enter IP adresses hostnames of valid O RCCMD senders for this client RCCMD senders are UPSMAN software C5121 C5111 or any RCCMD VI AY 2 compatible SNMP Adapters from LE other vendors Specifiy which RCCMD sender is permitted to execute actions on your RCCMD client If you do not enter any IP hostname any UPSMAN RCCMD sender will have permission to execute RCCMD calls Enter RCCMD EXE on command prompt for help Copyright GENEREX UPS A V C Uninstall RCCMD Licensekey 2SHARX3 RCCMD ver 4 0 1 1 W 22 2Z010 W 25 HM SVIK Uninstall KLLMV 66 21 2661 65 56 AM 19 968 WINCCexit exe 43 File lt s gt 4 563 169 bytes 6 Dirt
162. te to the log The file will be shrinked from the start so older entries will be removed first The default size is 1024 Kb To change the value use the 1 and keys The special value 0 means the file will not be shrinked This option specifies the name and location of the logfile The default is usr ups rccmd log You may change this value by overwriting the string in the options field or by selecting a file in the file browser To invoke the file browser hit the T ab key until the Browse button is highlighted then press Enter To reset all values to their defaults select the Default button by hitting the Tab key then press Enter To leave the Screen select either Ok or Cancel with the Tab key and press Enter Ok means accept all values as displayed on the screen Cancel means discard all changes made to the screen and switch back to the previous state Configure Shutdown Options generex host usr ups Shutdown Options File to execute usr ups rccmd_shutdown shl Cancel Browse Default Figure 129 RCCMD UNIX Shutdown Options File to execute This file will be executed if rccmd receives the SHUTDOWN command from the network Default is usr ups rccmd shutdown sh You may change this value by overwriting the string in the options field or by selecting a file in the file browser To invoke the file browser hit the Tab key until the Browse button is highlig
163. the computer that accepts the RCCMD signal ExecutePrg Command that is to be executed when receiving the RCCMD signal To start RCCMD execute the command rccmd95 Or start the program using the Windows 95 98 launch bar To start RCCMD in sending mode send enter the following line in your shutdown job RCCMD95 s a lt address gt p 6003 41 For lt address gt enter the TCP address of the machine to which you want to send the RCCMD signal Optional parameters p lt port gt TCP Port on which the RCCMD signal will be send The option a can be used several times if a shutdown on more remote computers in the network should be executed Do not use the CD License key more than once Copyright regulations page 1 If more RCCMD modules need to be installed for the shutdown additional CD license key must be purchased Additional license keys are available from your UPS dealer whereas the CD can be used again for the actual installation 2 11 RCCMD for Windows NT 2000 XP 2003 2008 The RCCMD remote console command is a program that allows the execution of programs on remote computers This tool is part of all UPSMAN supported operating systems with the exception of Windows 3 x With this tool it is possible to connect different operating systems Is the UPS Management Software installed on a Windows NT 2000 XP computer and should a remote shutdown be executed on a computer with a different operating system in a heterogeneous net
164. the secure shutdown of the guest systems is assured and avoids the lost of their data 4 2 RCCMD on VMware ESXi 4 x 5 x The RCCMD Software for VMWare ESXi Server is a Linux based TCP client for receiving shutdown calls from UPSMAN software any vendor CS121 any vendor or other RCCMD licensed applications like SNMP adapters etc from other vendors The following requirements are needed for the installation and configuration of RCCMD on VMware ESXi 1 A VMware vSphere is on a Windows workstation at present 2 A installed and configured vMA is on an ESXi server at present You can download the vMA from VMware Please take a look into the VMware documentation e g for the vMA 4 on page 13 http www vmware com support developer vima vma41 doc vma 41 guide pdf 3 For the transfer of the RCCMD package a SCP SFTP client like Filizilla or WINSCP is required In addition a terminal tool e g Putty is needed to open a command line on the vMA Both tools are common tools of an ESXi server or any other UNIX system and will not be described in this user manual 4 Amount of RCCMD VMware client licenses min One license vSphere client This is a grafical administration tool for ESXi server We suppose that you already have installed a vSphere client and will not describe its installation and control vMA The VMware ESXi server provides the vSphere Management Assistant vMA 4 x or 5 x as interface for external applications
165. them down in a special order This order and the desired actions shutdown of the guest systems have to be configured from the Administrator on the ESXi host RCCMD sends the shutdown signal to the host which will execute the defined actions 4 2 3 RCCMD Installation Download the RCCMD tar file from the website of your UPS manufacturer or www generex de by using a RCCMD license Copy the file RCCMDinst tar via the SCP client SFTP onto the vMA You can use a freeware SFTP client like Filezilla e Log on the vMA e g with a terminal tool like Putty e Create a temporary folder with mkdir e g RCCMD and copy the tar file into this new folder Extract the tar file as follows tar xvf RCCMDinst tar The following data occur after the extraction 109 roothvMNid1 cd z home wi admin roothvMNidl mv tmp rootfvmi4i 18 root vMid1 mkdir RCCHD roothvMh4d1 my recmdinst tar RCCMD rootwMidi1 k cd RBCCMD rootwMid1 REC CHD tar xvf recmdinst tar gpg pub txt installer info installer properties nstallRodMb bin natallRoCNMDb bin asc tallRCCMD bin mdS VErSionOEMN12 xml rootG vMid1 RCCMD 13 gpg pub txt installer properties installRCCND bin asc installer info installRCCHD bin installRCCHD bin mdS versionOEN12 xml rootGvMid1 RCCHD E Figure 138 Preparation of the installation You should be logged in as root Start the installation with the call installRCCMD bin Or as
166. u do not enter an address then every server has the permission to send a shutdown command If more than one CS121 or rather UPSMAN is existent thus a redundancy situation you need to enter more than one address as authorized sender 83 fi RCCMD Configuration Addresses Functions Logfile Execute Control UPSMAN alive checking Enable connection check Test connections Polling rate Connection retries T Execute at failure UPSMAH 3 fusr rccmd rccmad_execute sh Default Setti EditFile Browse RCCMD Redundancy Use RCCMD group redundancy IRCCMDCFG V4 0 0 11 Figure 108 Configuration RCCMD Functions If you want to use the UPSMAN alive checking recommended check the Enable connection check box Alive check is a signal send out to the UPSMAN or CS121 on port 5769 to check if the UPSMAN has still UPS data or not If this fails the scriptfile rccmd_execute sh will be executed which causes a messagbox coming up The polling rate default 30 min defines the polling of the UPSMAN service connect retries default 5 means after 5 unsuccessful connection tries an alarm will be triggered The function Use RCCMD Traps enables UPSMAN RCCMD UNMS traps which show the UPS status as a trap message If activated it will display a local message when the UPS status of the UPSMAN RCCMD server changes If you clic
167. ult 1800 seconds defines the polling of the UPSMAN service connection retries default 100 means after 100 unsuccessful connection tries an alarm will be triggered Heartbeats i rnei gt http localhost 8080 Options heartbeats htm Datei Bearbeiten Ansicht Favoriten Extras sly Favoriten 9 Web Slice Katalog v Heartbeats 127 0 0 1 Heartbeats v Options The UPS alive check can be used to monitor the availability of each sender Connections 7 Enable automatic UPS alive check heehee aoa sd Heartbeats E ainan gt by the use of CS121 UPSMAN Traps CS121 UPSMAN addresses Alive result i 192 168 222 210 Shutdown Settings by polling CS121 UPSMAN every 1800 seconds 192 168 222209 Ok Notification Settings eae z o Advanced Settinas and retry each failed connection 100 times Web Configuration When the alive check fails tnen RCCMD will use the follow Run this command file C Program Files RCCMD alive bat Test UPS connections Run alive check now Save Changes Figure 21 RCCMD Weblnterface Configurator Heartbeats You can test the UPS connection if you click the Run alive check now button the port 5769 will be tested Click the Save Changes button prior of the leaving of this site to save your changes You can enable the redundancy management feature into the m
168. un this command file lusrirccmdlrccmd execute sh Edit File Nane Figure 158 RCCMD Weblnterface Notification Settings Click the Save Changes button prior of the leaving of this site to save your changes Advice We recommend not to change the command sequence for the shutdown of a vMA The features Insert command and Edit File just make sense at other OS 120 Firefox v i Shutdown Settings e https 192 168 200 50 8443 Options shutdownSettings htm C 4 Google Shutdown Settings v Options When RCCMD shuts down your operating system it will use the following sequence Connections Heartbeats Redundancy rccmd Shutdown Settings shutdown ESXI sh e Notification Settings e VMware Settings S ESXI_HOST_SHUTDOWN Advanced Settings exit Web Configuration Command sequence Settings file usr rccmd rccmd_shutdown sh n Edit File Save Changes Figure 159 RCCMD W ebinterface Remote Access vMA Shutdown Settings The VMware Settings menu appears only if you install the RCCMD webinterface on a vMA this menu shows the parameters which you entered during installation https 192 168 200 103 8443 Options v mwareSettings htm EJ Google IP 192 168 200 103 VMware Settings v Options Virtual Machine Management within ESXi Connections 3 o Heartbeats The virtual machine that runs RCCMD must not be shutdown Or
169. und ein Passwort Ausgabe der Website RCCMD Config Benutzername Passwort Figure 190 RCCMD Weblnterface Configurator Remote Access 142 6 3 Old RCCMD Configuration on MAC OSX Add the IP address of the RCCMD server which is allowed to send a shutdown to this client OG RCCMD Configuration 1 Addresses Functions Logfile Execute Control _ IP address list of all RCCMD servers that are allowed to senda shutdown command to this client no entry means every server Add Address JRCCMOCKG V4 0 0 11 Figure 191 RCCMD IP Address Window Attention If you do not enter an address then every server has the permission to send a shutdown command If more than one CS121 or rather UPSMAN is existent thus a redundancy situation you need to enter more than one address as authorized sender 143 Addresses Functions Logfile Execute Control _ ee UPSMAN alive checking vi Enable connection check Test connection s Polling rate 30 min Connection retries 5 Execute at failure fusr rccmd recmd execute sh Default Set Edit File Ou Redundancy Use RCCMD group redundancy NJNJA AT 0 Figure 192 RCCMD Configuration Window Functions If you want to use the UPSMAN alive checking recommended check the Enable connection check box Alive check is a signal send out to the UPSMAN or CS121 on port 5769 to check if the UPSMA
170. upported in all Windows versions and it should be tested before using The RCCMD Version 4 0 1 0 or higher provides a grafical configuration of the RCCMD relay function Click the Configure button Logfile configuration Max logfile size 512 Kb View log Execute at mail signal from RCCMD server C Program FilesYRCCMD mail bat Configure Edit file Execute at message signal from RCCMD server C Program Files RCCMD message bat Edit file Execute at execute signal from RCCMD server C Program Files RCCMD execute bat Edit file Execute at shutdown signal from RCCMD server C Program Files RCCMD shutdown bat Browse C Contigue Edit file RCCMD ver 4 0 1 7 lt Back Install Cancel Figure 65 RCCMD Client Shutdown Configuration Tag the RCCMD shutdown relay into the Available Commands window and click the gt button to add this function into the Current Sequence 52 File C Program Files RCCMDshutdown bat Available Commands Current Sequence Hibernate Windows Shut down Windows Suspend windows Quit Lotus Motes i Quit Siemens SIMATIC Add command uit Applications TE Wait some seconds Description of Add custom application ACCMD shutdown relay Relays RCCMD shutdown command to another computer Enter IF address or hostname of the remote computer wou want to shutdown Fig
171. ure 66 RCCMD Shutdown Relay The following panel will appear in which you can enter the desired IP address range Configure Shutdown Seque File C RCCMD shutdown bat Available Commands Current Sequence Configure RCCMD shutdown relay Enter IP address or hostname of the remote computer you want to shutdown with RCCMD OR Enter an IP range of remote computers you want to shutdown with RCCMD From 192 168 222 1 to 192 168 222 254 Use secure connection SSL Relays RCCMD shutdown command to another computer Enter IP address or hostname of the remote computer you want to shutdown RECM Cancel OK Figure 67 RCCMD Configuration IP Address Range Additionally you can enable the SSL function see also chapter 3 8 If you want to remove single IP addresses mark the line with its desired IP address and click the lt button 53 Configure Shutdown Sequenc File C Program Files YHCOCMDAshutdown bat Available Commands Current Sequence Hibernate Windows Shut down Windows Suspend Windows ACCMD shutdown relay to 192 168 222 1 Quit Lotus Notes RCCMD shutdown relay to 192 168 222 2 Quit Siemens SIMATIC 900 RECMD shutdown relay to 192 168 222 3 Quit Applications ACCMD shutdown relay to 192 168 222 Walt some seconds RCCMD shutdown relay to 192 168 222 5 ACCMD shutdown relay RECHO shutdown relay to 192 168 222 6 TTT p
172. ut has identical functions as any other RCCMD RCCMD for AS 400 comes with a separate user manual with the product Download AS400 RCCMD Manual 155 10 RCCMD FAQ In this chapter we will give you some solutions of well known problems FAQ Frequently Asked Questions Problem The execution of sudo sh rccmd shutdown sh on ESXi 4 with vMA 4 1 fails with the following error message or similar Compilation failed in require at usr lib perl5 site_perl 5 8 8 VMware VIFPLib pm line 10 BEGIN failed compilation aborted at usr lib perl5 site_perl 5 8 8 VMware VIFPLib pm line 10 Compilation failed in require at usr rccmd upsVIShutdown pl line 12 Can t load lusr lib perl5 site perl 5 8 8 libvmatargetlib perl so for module vmatargetlib perl libtypes so cannot open shared object file No such file or directory at usr lib64 perl5 5 8 8 x86 64 linux thread multi DynaLoader pm line 230 BEGIN failed compilation aborted at usr rccmd upsVIShutdown pl line 12 at usr lib perl5 site perl 5 8 8 VMware Vmal argetLib pm line 10 Reason The procedure of the authentication is completely different from vMA 4 0 to vMA 4 1 The integration of RCCMD is not possible unless you use a newer version of RCCMD or to use vMA 4 0 instead Solution Use the vMA 4 0 A new setup for integration of the vMA 4 1 will be released after November 2010 Problem You get the following error after the execution of the upsVISh
173. utdown pl vi adminBYMA rcecmd1S upsVIShutdown pl 19 1 1 2 Use of inherited AUTOLOAD for non method vifplib perl CreateVIUserInfo is dep recated at upsVIShutdown pl line 46 Undefined subroutine vifplib perl CreateVIUserInfo called at upsVIShutdown p l line 48 vi admin uMA rcemd1 vi admin vMA rcemd1S vi adminBYMA rcemd1 S vi adminBYMA rcemd1 upsVIShutdown pl 19 1 1 2 Use of inherited AUTOLOAD for non method vifplib perl CreateVIUserInfo is dep recated at upsVIShutdown pl line 49 Undefined subroutine vifplib perl CreateVIUserInfo called at upsVIShutdown p l line 48 vi adminBYMA rccmd1 vi adminBYMA rcemd1S _ Figure 201 Error after execution of upsVIShutdown pi 156 Solution You do not use the latest RCCMD version Please download the current RCCMD version from our website www generex de Problem Shutdown of NetApp storages Solution Typically all low cost NAS systems export their NFS shares in the asnyc mode This is an extremly fast write process which secures that no data is lost if the power suddenly fails As long as the user has not changed the default NFS protocol write mode from async to sync than there is no risk to lose data Anyhow an UPS should be connected to any NAS to avoid that network computers will not be shut downed but rather will die down For this case we recommend to connect an UPS to the NAS and we think it makes sense to connect an UPS to a NAS syste
174. version which is used for the installation or rather uninstallation only In addition the RCCMD Web Configurator is using a Java web server jetty You can deactivate the RCCMD service RCCMDW eblf into the services administration and RCCMD is running without Java 2 1 Installation of RCCMD Prior of the start please make sure that you have full administrator rights in order to complete the installation Step 1 Put the CD into the CD ROM drive of your computer or download the software into a specific directory Step 2 Please execute the installation program installTRCCMD exe in order to copy the files to your system and chose a desired setup language InstallAnywhere will guide you through the installation of RCCMD Client Itis strongly recommended that you quit all programs before continuing with this installation Click the Next button to proceed to the next screen Ifyou want to change something on a previous screen click the Previous button You may cancel this installation at any time by clicking the Cancel button Installer version 69 Figure 2 Introduction In the next menue you can see the progress column where the next steps are visible Click the NEXT button to continue Enter your license key RCCMD Client License Key Enter license key 12SHARX3 Usually the license key is located on the installation booklet or on a label on the reverse side ofthe CD sleeve Figure 3 Licen
175. vi admin sudo installRCCMD bin roothwMi41 ihi cd RCC CMD root vNadi RCC CMD installRCCMD bin D Figure 139 Execution of the binary file and start of the installation Select the language and press the enter key 110 RCCHD created with Installinywhere Preparing CONSOLE Mode Installation Installanywhere will guide you through the installation of RCCMD Client s strongly recommended that you quit all programs before continuing with s installation in the installation If you Want to change something on amp previous You may cancel this installation at any time by typing quit PRESS lt ENTER gt TO CONTINUE x86 64 GNU Linux Recognized VMware ESXi environment lt ENTER gt TO CONTINUE I Figure 140 Introduction OS recognition Enter the RCCMD license key the hostname or rather the IP address of the ESXi host the root password and note the license agreement Figure 141 RCCMD License Key Select the desired product features YOU WOULD Figure 142 RCCMD Product Feature Selection 111 4 2 3 1 RCCMD Installation without vCenter Select option 2 if you do not use a vCenter credentials will be required vSphere Client for Windows ENTER THE NUMBER FOR YOUR CHOICE OR PRESS lt ENTER gt TO ACCEPT THE DEFAULT Host Hosts may be configured in the Web inter or IP Address Default Figure 143 RCCMD vCenter Selection ESXi Access Data Enter the shutd
176. wn automatically If a shutdown was suppressed because of the existing redundancy at this point of time but the problem was solved at the UPS intermediate you can reset the shutdown with the function Send RCCMD cancel shutdown The client which received the shutdown will be encouraged to reset it Please take a look into chapter 3 4 or rather 3 4 1 for further information about RCCMD with redundancy Click the Save Changes button prior of the leaving of this site to save your changes You can change or rather extend the shutdown sequence into the Shutdown Settings menu The shutdown bat will be executed by default rem created by setup echo off set path path C Program Files RCCMD ExitWin exe shutdown force clis 22 E hitp localhost 3080 Options shut 50 vnSettings htm s r Favorten Web Siice Katalog Shutdown Settings 127 0 0 1 Shutdown Settings When RCCMD shuts down your operating system it will use the following sequence Shut down System Settings file C Program Files RCCMDishutdown bat Figure 23 RCCMD Webinterface Configurator Shutdown Settings If you want to execute a powershell script you can edit or add desired scripts here If you want to edit the shutdown bat mark Shut down System click the Edit Command button and the Save Changes button Please note to restart RCCMD 127 0 0 1 Shutdown Settings
177. work the RCCMD tool is necessary The RCCMD tool works in two different modes The module works like a normal program start as Send Mode in order to send RCCMD commands s a to other computers In the so called Listen Mode installed as a NT 2000 XP service the program as background process waits for a command from Send Mode of the RCCMD module In Listen Mode the RCCMD module waits for the ping signal After reception of this signal the module executes a batch file or program GP Attention For first time users we do recommend the use of the RCCMD Wizard which makes the configuration easier Please start the RCCMD Wizard from your program group Attention Please do not use the wizard and manual settings at the same time Eventually the RCCMD service must be allocated with special system privileges if certain commands and programs like messaging using net send shutting down databases and the like are to be executed The RCCMD start up parameters in the control panel must be set to the administrator superuser account enter password twice together with the correct password If you are not allowed to use the administrator account you have to create an account which has all the rights to shutdown this NT 2000 computer Change to 42 the control panel and mark the RCCMD in the list change the start up parameters to this account and enter the any administrative account Now the RCCMD has been ins
178. xecute ACCMD calls Install RECHO client Uninstall RECHO Licensekey fi SHARA g RCCMD ver 4 0 1 6 Figure 53 Client Installation Click the Next button IP address list of all RCCMD servers that are allowed to send a shutdown command to this client no entry means every server Enter an IP address for example 192 33 44 55 IP address or name 192 168 222 243 Configure RCCMD ver 4 0 1 7 lt Back Next gt Figure 54 Add IP Address Window Step 4 Add the IP address of the RCCMD server which is allowed to send a shutdown to this client Attention If you do not enter an address then every server has the permission to send a shutdown command If more than one CS121 or rather UPSMAN is existent thus a redundancy 44 situation you need to enter more than one address as authorized sender Advanced network settings IP address and port IP to bind to 127 0 0 1 Browse for IP on Port 6003 SSL 7 UPSMAH UPS Use secure connection SSL Accept expired certificates default values Message Port for messages 361 Configure RCCMD ver 4 0 1 7 Cancel Figure 55 Advanced Network Settings Step 5 If you want to use the secure connection SSL click the Configure button and check the SSL box and you can change the port for the messages UPSMAN alive checking Enable connection check Test con
179. yntax for the NT consol for RCCMD in lt Listen mode gt 37 rccmd debug I a IP adress h hostname p port command The command can be either a program or a path for another batchfile on this workstation The command file should be given with full path The p port option can be included if you want to start RCCMD more than once at a single workstation to proceed different commands for different events The default port number is 6003 use any other availabe port number for different RCCMD commands RCCMD in the send mode rccmd debug s a IP adress h hostname p port This command is regularly used in the batchfile of the sender shutdown bat and sends a ping to the computers IP adress or hostname If this ping has been answered the next command RCCMD s may be executed etc When you have finished the edition of the bat files click the Restart RCCMD button into the System Status menu http localhost 8080 Status systemStatus htm Datei Bearbeiten Ansicht Favoriten Extras we Favoriten Web Slice Katalog v System Status 0 0 0 0 0 0 0 1 v Status System Status View Event Log Current status of RCCMD is running e stem Status Options Help Figure 48 Client Installation successful Window RCCMD is now running as Service with automatic startup To configure the automatic start of RCCMD use administrative rights and control panel service to chang
180. zilla Firefox File Edit View History Bookmarks Tools Help lt a v e A http localhost 8080 Status systemStatus htm v Go0 oN Most Visited v Getting Started latest Headlines v 6 System Status op a nee 0 0 0 0 0 0 0 1 gt a a m LJ J EJ a 7 Status System Status View Event Log Current status of RCCMD is running e System Status Update Status Restat RCCMD Start RCCMD Stop RCCMD Done Figure 188 RCCMD WeblInterface System Status 141 You can open the RCCMD user manual into the menu Help ad you can follow the link to www generex de E E Manuals Mozilla Firefox el i httptocainost s080 Helpimanuals ntm v fay a fig Most Visited a Getting Started jjLatest Headlines v 3 Manuals qr 0 0 0 0 0 0 0 1 Find more documemation online here Nane Figure 189 RCCMD Weblnterface Help 6 2 RCCMD Remote Access RCCMD provides its own web interface from version 4 0 1 9 or higher Therefore it is possible to configure and control RCCMD remotely Please note that the firewall port 8080 TCP is enabled Enter the following into a web browser to connect to a workstation where RCCMD is running http IP address of the RCCMD client 8080 Status Event Log View Event Log These are the events that have occured on this computer System Status Authentifizierung erforderlich Q http 192 168 200 17 8080 verlangt einen Benutzernamen

UPS-Management Software Benutzerhandbuch

Contents

Download Pdf Manuals

Related Search

Related Contents