Home

TLT-1C User Manual

1. amp om 7 Note The above three commands if sent in the past not on the server connection or other reasons not connected the reply 1 If the connection is not on the server the reply SEVER BUSY PLEASE TRY AGAIN LATER 2 If there is no GPS location then the reply GPS UNAVAILABE PLEASE TRY AGAIN LATER 3 for domestic policy reasons in the country to use Google Maps will lead to deviation from the actual address TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 4 1 16 ACC function and state of charge detection switch 1 ACC charging detection TLT 2H detected by an external vehicle ACC ACC leads the state take the car to achieve ACC ON on the TLT 2H car battery built in battery charging parking ACC OFF the stop on the TLT 2H built in battery charger 2 ACC status command prompt switch Open the command prompt ACC Status format 091 user password For example 0910000 ACC status prompted to close command format 090 user password For example 0 900 000 Description When the TLT 2H received 091 orders confirm the user password correctly send the confirmation to the sender Information ACC STATE PROMPT ON When the ACC in the on off switch text mode all stored numbers immediately to send the current location information regardless of GPS data is valid and AUTO START AUTO STOP as the opening ACC ACC switch off when the upload data state marked When TLT 2H received 090 orders confirm
2. 803 Password APNHAPNUser name APNPassword GPRS access point settings 804 Password Fixed IP address and port Set IP address and port number 805 Password Sampling intervall From the number of each clause N From time to time take the car to track mode settings 8064 Password Request From Single Location 8074 Password X Set the sampling rate history 8084 Password 24 From the historical data 24 hours 8084 Password From all the historical data 809 Password x y From time to time set the throttle stop mode RESETHOOOO Reset all the configuration information after reboot RESTARTHOOOO Restart device 081 Password GPRS mode open the invalid data upload 080 Password GPRS mode close invalid data upload
3. power alarm calling fence alarm calling speed alarm etc after the success of the sender to send the confirmation to the SET VOICE CALL OFF When the TLT 1C before calling open order confirm the user password is correct open the calling features including the SOS distress power failure alarm calling fence alarm calling speed alarm etc after the success of the sender to send confirmation message to the SET VOICE CALL ON 4 1 5 Phone positioning function TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Note When the stored one of the three phone numbers of calls come in and hang up after ringing sound 2 5 then the call number to send the location information such as 3 1 1 status information tips for the STATE CALL Non stored phone numbers hang up incoming calls directly without any treatment 4 1 6 Monitoring functions Instruction format 00X user password For example 0000000 Description When the device receives the instruction correctly recognized the user s password according to the value of X set the handset switch state X 1 the handset closed the monitor mode After the success the sender should send the confirmation messages SET PROFILE OK CURRENT PROFILE SILENT Handset is turned off if the stored user phone calls in does not follow any prompts in about 10 seconds after the automatic answer the user can listen to the sound track side but the track side can not hear the voice of t
4. 5 1 22 ACC shift detection and alarm Shift alarm locale command 008 user password Rzzz z Shift off the alarm command 009 with a password function When the TLT 2H received 008 user password Rzzz z command and verify that the password is correct set the alarm for mobile zzz z radius zzz z domain of 0 1 999 9 units of TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 KM After the success returned to the sender confirmation message SET MOVE RADIUS OK After the success of mobile police locale if the ACC TLT 2H detected by the opening switch to the off state then the delay of 3 minutes read the current location as the origin of coordinates regardless of the validity of gps data and zzz z as radius of the electronic area deployment In the ACC is off if TLT 2H beyond the deployment region is detected SMS mode the stored number immediately sent to a shift of all alarm messages status information is marked as STATE ACC OS GPRS mode immediately From the current location information server the status is marked as ACC OS and dial stored phone Whether by the 150 151 call control reset only to send text messages do not make a call the deployment area and if it once again into the deployed area the location information will upload or send text messages and dial stored phone alarm which Information in the state marked as ACC RS Once the TLT 2H state is detected by the ACC switch to turn off after the alarm automatical
5. L Hitems after the success to send the confirmation message GPS AUTO MODE yy zz xxx Minutes Note 1 Set S L H and other parameters if the high is 0 then we must make zero For example To turn off gps30 minutes will set the S030 but not set to S30 2 Hzz opened GPS to set the total time not less than Lyy 3 199 instruction set of the parameters are not lost restart the reset will not change until reset 4 Only in exceptional power saving mode the device can be set in accordance with the parameters of the timer switch 199 GPS other modes will not 2 Special power saving mode is on TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Command format 188 user password For example 1880000 Description When the device is set to command successful 199 send 188 commands to take effect When you receive the confirmation code 188 instructions correctly to switch to GPS mode power saving mode the sender replies to the confirmation message GPS AUTO MODE ON OK After entering power saving mode the device 199 in accordance with the parameters set by instruction time switch GPS in order to achieve power saving purposes Such as setting 1990000SO30L01HO3 sending 188 to enter this mode the device according to the 199 instruction set turn off the GPS 30 S030 minutes and then open the 1 minute L01 if the GPS in the open for 1 minute L01 localization directly off GPS 30 4 gt 4 S030 If a minute L01 did not
6. Mode Point to Stored phone Air Password 0000 Point GPS Status Open Time to send Stop The number 1 of base stations Power failure Off disarm Electronic fence Close Calling switch Open alarm Service Air GPRS Password 0000 GPRS user V500 center name number ANP CMNET IP Address 0 0 0 0 0000 Shift alarm Close Calling switch Open Off petrol and Open non off petrol Speed alarm Close electricity and electricity Historical Stop Historical Data Stop Parking Stop data Upload throttle sampling upload ACC switch Open Upload invalid Close Go cart track Close state tips data upload 6 4 Instruction Set Instruction Explain 700 Password Point to Point mode 710 Password GPRS mode 003 Password E Wxxxx xxxxN Syyyy yyyyRzzz z Fenced area set in degrees minutes 004 Password E Waaa aaaaaN Sbb bbbbbRzzz z Fenced area set in degrees 005 Password RZZZ Z coordinates Set the fenced area the current location 100 Password Power saving features 1224 Password x Set the speed alarm 150 Password Close Caller 151 Password Open calling 170 Password Open the command call restrictions 171 Password Close instructions call restrictions 210 Password Close fence detection 211 Password Open fence detection 222 Password Open GPS 333 Password Close GPS TLT 1C GPS GSM Vehicle T
7. 16 39 45 BS 25ee0dff Fix A ID 353686009002030 STATE SMS Invalid sample data Lat 22 50500 Long 114 01000 Speed 0 OOKM H Direction 315 00 Date 2008 04 25 Time 16 39 45 BS 25ee0dff Fix V TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 ID 353686009002030 STATE SMS Note If the cold start and the GPS does not locate then return invalid information as shown below Cases ERROR GPS GPRMC FRAME DATA BS 27971054 ID 353686009002030 STATE SMS Note If the cold start and the GPS does not locate then return invalid information is shown below Eg GPS UNAVAILABE PLEASE TRY AGAIN LATER 2 1 2 Show Location on Map 1 Download Google Maps software from http earth google com Fie bm yew po asd tee A Frets Fettiverenses Orectone 1 fytecg AMENI b tt 22 30 4272M 14 Soot Cd 2 22 39 4279116 eet EJ 22 2a 442 soor E 22 33 4828 14 Soot L Lij 22 3 etze rte S diast LE 22 D 28H 14 S aat MEESE ESE S ULET ai TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 2 start Google Maps software for more information on the Google Maps software please refer to http earth google com as shown above Note change in location data format or you can copy http maps google com in the Internet browser to connect Google Maps site shows location map 3 send 666 code SMS command to the TLT 1C have latitude and longitude data Enter your latitude and longitude received fro
8. 1C receiving the order confirm the user password is correct update GPRS access point for the new access point set up after the success of confirmation to the sender to send a short message If the sender is the instruction format 1 the return confirmation message SET GPRS APN OK If you send the order form 2 back to confirm the information SET GPRS ACCOUNT OK Note APN factory set or reset to CMNET APN for 3 to 35 letters numbers dot Underscore _ and hyphen TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 formed characters APN APN username user and password respectively 3 to 20 characters consisting of numbers and letters such as the need to change in domestic use 2 set the TCP IP server IP address and port number Instruction Format 804 user password fixed IP address port example 804 0000 222 125 12 32 80 Note When TLT 1C received the order confirm the user password is correct and update the internal save TLT 1C The IP address and port number set up after the success of the sender send a confirmation to the short message SET SERVER IP AND PORT OK The server IP address and port number provided by the vehicle monitoring service provider 3 regular data upload settings Instruction Format 805 user password From each sample interval T N number of data section Example 805 0000 6 10 Function sampling time T in seconds the domain of 10 59999 u
9. TLT 1C again into the fenced area will be set immediately TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 sent to the server 3 2 16 format of location information Tips for the state information RS Also call a telephone number stored in the first If unsuccessful shutdown or not connected then in turn call the second third l set the fenced area According to the different coordinates input format the user can choose the following format command operation Instruction format 1 003 user password E Wdddmm mmmmN Sddmm mmRzzz z For example 0030000E11406 0024N2233 4230RO0 1 Description E E W W N north latitude S south latitude Used in this example is EandN please select the appropriate location according to the actual coordinates of format settings The meaning of the various parts of the sample as follows Edddmm mmmm is divided into units of degrees longitude information which said ddd degrees mm mmmm that sub Decimal point behind the four followed by zero can not be omitted Nddmm mmmm is divided into units of degrees latitude information which dd that degree mm mmmm said points Decimal point behind the four followed by zero can not be omitted zzz Z is the domain of radius 999 9 0 1 in units of KM When the TLT 1C receiving the order to confirm the user password is correct to return to the sender to confirm the short message SET GEO FENCE OK and open the electronic fence function Instr
10. default resolution of 240 320 If you think that image is too small you can send commands 2 custom picture size in which the representative picture of the width of the WWW HHH on behalf of picture height ZZ for the zoom level you can set the size to comply with the resolution of your phone Note WWW HHH these two values can not be greater than 1000 ZZ between the values proposed 1 20 when the device receives the command make sure the correct user password immediately after reading the GPS information recognition information valid send the current location of the Google Maps screenshot of the website you set the capture resolution of the resolution Screenshots URL example http maps google com staticmap center 22 554 765 174 10471 6 amp zo00m 6 amp size 240x240 amp ma ptype mobile amp markers 22 554765 114 104716 bluea amp sensor false amp hl cn 4 1 15 Single Location Google Maps link instruction to return Format 669 user password for example 6 690 000 Description When the device receives the command make sure the correct user password immediately after reading the GPS information recognition information is valid send the current location of the Google Maps link to the number and user available through your PDA or smart mobile Internet Google Maps view in the current location URL Example http maps google com maps f q amp hl en amp q 22 554765 1714 104 716 amp ie UTF amp amp z 6 amp iwloc addr
11. hours 8084 Password From all the historical data 8094 Password x y From time to time set the throttle stop mode RESETHOOOO0 Reset all the configuration information after reboot RESTARTHOOOO Restart device Instruction Explain 700 Password Point to Point mode 710 Password GPRS mode 003 Password E Wxxxx xxxxN Syyyy yyyyRzzz z Fenced area set in degrees minutes 004 Password E Waaa aaaaaN Sbb bbbbbRzzz z Fenced area set in degrees 005 Password Rzzz z Set the fenced area the current location coordinates 100 Password Power saving features 1224 Password x Set the speed alarm TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 150 Password Close Caller 151 Password Open calling 210 Password Close fence detection 211 Password Open fence detection 222 Password Open GPS 333 Password Close GPS 4xx Password 666 Password From time to time point to point mode Location to return a single user ID 777 New Password Old Password Change Password Stored number Password Serial number Change the stored number 8014 Password New User Change the GPRS user name 8024 Password new service password old service password GPRS service password change 8034 Password APNH GPRS access point settings
12. no GPS location then the reply GPS UNAVAILABE PLEASE TRY AGAIN LATER 3 for domestic policy reasons in the country to use Google Maps will lead to deviation from the actual address 5 1 19 invalid data is uploaded switch Format 08X user password 4 Function When the TLT 1C received the instruction to confirm the user password is correct according to the value of X is upload invalid data set switch state X 1 open invalid data upload After the success confirmation to send the short message INVALID DATA UPLOAD ON at this time whether TLT 1C GPS data received is valid will be uploaded to the server X 0 close the upload invalid data set after the success of the short to send the confirmation message INVALID DATA UPLOAD OFF then close the invalid data upload only upload valid data Note The factory set or reset the state to stop after the upload invalid data the instruction set of the state not switch until it received the relevant instructions to change again or reset operation Note 1 this function is only valid in the GPRS mode 2 default is OFF 5 1 20 Call limit switch instructions Open the command limit calls 170 user password TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 for example 1 7 Call restriction off command 171 user password for example 1 710 000 Description When the device receives the call limit open command confirm the user password correctly send the number of replies to t
13. password respectively numbers and letters FTP server to set their own customers the upgrade file please consult the product sales 6 Accessibility 1 the command reset RESET 0000 Description This command resets all the configuration information after the restart to the factory configuration 2 the instruction restart RESTART 0000 Description This command only restart the TLT 1C do not reset the configuration information 3 the current configuration of the module to read SMS command format GTAS Function When the module receives instructions return all the settings stored in the module Data format IMEI marked as code MOD Point to Point SMS P2P 2 messaging platform SMS SC GPRS GPS normally open ON normally closed OFF power AUTO HFR hands free switch MTPRF Monitor SILENT normal NORMAL BS base station information to return the number of GEO FENCE ON OFF longitude longitude latitude latitude R radius minimum 0 1KM GEO FENCE STATE RS OS DEFENCE ON OFF power failure alarm switch VOICE ON OFF switch calling POWER ON OFF power switch off oil RATE XX speeding baseline ST location information request interval timer TN SMS mode timer request number INVALID UPLOAD Invalid Data From switch MOVE displacement of the alarm radius displacement alarm switch ACC PROMPT ACC switching state switch GU GPRS user name password SRV Server IP address port number AP
14. the general application of SMS Point to Point The product s default mode is SMS point to point mode do not switch if from the GPRS mode to switch to point mode press the 2 1 0 operation 2 10SMS point to point mode Command format 700 user password 4 For example 7 000 000 Description When TLT 1C receive the SMS to confirm the user password is correct the switch to SMS application mode After the success of the sender to send the confirmation to the SET MODE OK CURRENT MODE SMS P2P 2 1 1 Single positioning request instructions Command format 666 user password 4 example 6 660 000 Description When the TLT 1C receiving the order confirm the user password is correct read the GPS information regardless of the validity of the original software set it with the base station with return return to the sender Data format TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Lat latitude latitude value precision after the decimal point 5 Long longitude direction longitude value precision after the decimal point 5 Speed speed KM H precision after the decimal point 2 Direction Heading accurate to two decimal places Date Date YYYY MM DD Time Time HH MM SS GMT BS base station information FIX Position Status A V ID IMEI STATE Information Status Valid data sample Lat 22 50500 Long 114 01000 Speed 0 OOKM H Direction 315 00 Date 2008 04 25 Time
15. the state prompted the OVER SPEED speeding alarm if it detects the speed of GPS in less than X it indicates the speed at this time to return to a safe speed driving TLT 1C immediately 3 2 16 server sends a location information format information in the state prompted the SAFE SPEED 5 1 13 Historical data uploading In SMS mode need to use this feature to switch to GPRS mode prior to the IP APN settings etc can only be completed specific instructions and upload the data format please refer to GPRS mode three step basic setup l historical data records set Command format 807 user password X Example 807 0000 30 TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Note X is a historical record of the sampling frequency an integer the domain of 0 999 unit is seconds When the TLT 1C receiving the order to confirm the user password is correct set the historical record of the sampling frequency is X If X 0 then close the historical data records if X 0 then the start time interval to X seconds for the GPS data received and stored after a successful return to the sender to confirm the information SET SAMPLING OK Note 1 each data record about 100B BYTE can store up to 3000 2 the data covered by the stack of records that way When the recorded data over 3000 the new data received will automatically overwrite the earliest recorded data 3 if the power saving feature is turned on and the TL
16. to a 3 1 1 format of location information Information prompted the state to STATE OS Also call a telephone number stored in the first If unsuccessful shutdown or not connected then in turn call the second third When the TLT 1C set to re enter the scope of the fence will immediately send to the No 3 stored location information of a 3 1 1 format Information in the state prompted the STATE RS Also call a telephone number stored in the first If unsuccessful shutdown or not connected then in turn call the second third 1 Set the fenced area According to the different coordinates input format the user can choose the following format command operation Instruction format 1 003 user password E Wdddmm mmmmN Sddmm mmRzzz z Example 0030000E11406 0024N2233 4230R0 1 Description E E W W N north latitude S South latitude Used in this example is EandN please select the appropriate location according to the actual coordinates of format settings The meaning of the various parts of the sample as follows Edddmm mmmm is divided into units of degrees longitude information which said ddd degrees mm mmmm said points Decimal point behind the four followed by zero can not be omitted Nddmm mmmm is divided into units of degrees latitude information which dd that degree mm mmmm said points Decimal point behind the four followed by zero can not be omitted zzz Z is the domain of radius 999 9 0 1 in units o
17. E OFF open a single rectangular electronic fence is SET SQUARE GEO FENCE GX OFF Note If you set multiple alarms occurred while rectangular enclosure the priority call G1 fence fence G2 G3 G4 only to send the relevant location information not make the call Factory configuration and reset the default state for the RS TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Attention Set of three ways of electronic fencing Choose one when the product after receipt of the electronic fence electronic fencing instruction set feature automatically opens When turned off the electronic fence is open again after the previous set are still valid 5 1 12 Speed alarm Instruction Format 122 user password X Example 122 0000 250 Note X is the speed reference value the data type integer in units of km hour KM H the domain of 0 999 When the TLT IC receiving the order to confirm the user password is correct it will set the speed reference value X X 0 I close the speed alarm function X 0 speed alarm function is turned on after the success of the first stored to send confirmation information SET RATE LIMIT X When the speed alarm function is turned on TLT 1C began to read the speed of GPS data and comparison with X real time If the GPS speed is greater than in X the instructions at this time for speeding TLT 1C a 3 2 16 immediately sent to the server location information formats information in
18. M H precision after the decimal point 2 Direction Heading accurate to two decimal places Date Date YYYY MM DD Time Time HH MM SS GMT BS base station information FIX Position Status A V ID IMEI STATE Information Status Valid data sample Lat 22 50500 Long 114 01000 Speed 0 OOKM H Direction 315 00 Date 2008 04 25 Time 16 39 45 BS 25ee0dff Fix A ID 353686009002030 STATE SMS Invalid sample data Lat 22 50500 Long 114 01000 Speed 0 OOKM H Direction 315 00 Date 2008 04 25 Time 16 39 45 BS 25ee0dff TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Fix V ID 353686009002030 STATE SMS Note If the cold start and the GPS does not locate then return invalid information Such as ERROR GPS GPRMC FRAME DATA BS 27971054 ID 353686009002030 STATE SMS 5 1 4 Change the GPRS user name Instruction Format 801 user password the new user name For example 801 0000 username Note When the TLT 1C receiving the order confirm the user password is correct update the user name the new user name set After the success of the sender send a confirmation to the short message CHANGE USERNAME OK 5 1 5 GPRS service password change Instruction Format 802 service password user password new password old services Such as 802 0000 1111 0000 Description When TLT 1C receiving the order confirm the user password and the old ser
19. N GPRS access point APN User Name APN password SAMP From the sampling interval first upload a few articles go cart track uploaded regularly TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 mode SAMP2 From the sampling interval first upload a few articles uploaded regularly stop throttling mode HISTORY SAMP History By sampling interval 4 read the current number and password SMS command format GTAN Function When the module receives instructions return the module all the numbers and passwords stored including the service center number and password the user number and password Data Format Ul Number 1 password U2 Number 2 password U3 No 3 password SC Service Center number service code 6 2 The state labeled Status Corresponding identity 666 single request SMS 4XX regularly sent TIMER Phone Location CALL Answer ANSWER Seek help SOS Power failure alarm alarm DEF A fence OS Finalists selected RS Speed alarm OVERSPEED Safe speed SAFESPEED Historical Data Upload STORAGE Low voltage alarm LP 806 single hair positioning SMS From time to time to go car AUTO track throttling TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 From time to time stop AUTOLOW 6 3 List of products manufactured state Configuration Status Configuration Status Configuration Status items items items
20. O FENCE OK GPS data is invalid if the date is to give up continue to receive the next one if 50 seconds have not received valid data then return to the sender to send reminder ERROR GPS DATA TRY AGAIN LATER After the GPS set to resume their original state on off adaptive Note 1 fences can not exceed the radius of its domain the fractional part of the right to a value of zero must enter zeros For example R 1 must be entered as 1 0 2 if the calling state is off it will not make calls send text messages to pre existing users only 3 degrees and is divided into 60 binary conversion that ld 60m 2 Open the e fence 211 user password When the TLT 1C receiving the order to confirm the user password is correct to open the electronic fence to return to the sender to confirm the short message GEO FENCE ON 3 Close E fence 210 user password When the TLT 1C receiving the order to confirm the user password is correct closed electronic fence to return to the sender to confirm the short message GEO FENCE OFF 2 gt set the rectangular range of the electronic fence Format 006 user password GX 10 1 0 E W longitude limit N S latitude limit E W longitude limit N S latitude lower Eg 0060000G1 I0 E114 10004N22 55705 E115 10006N23 55706 Note GX said the electronic fence X X range 1 16 IO fencing in and out of TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 all alarms I selected as a fin
21. Support alarm have 3 preset phone number TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 4 Support single location and continuous tracking 5 Support cut off electricity and oil function and recovery command 6 High reliability circuit design in line with the automotive electronics industry standards 1 3 Notes 1 Please read this manual carefully and make the correct mode of operation to avoid any errors 2 Professional installation recommended this product to dealers to ensure the safety of use installation and covert 3 Pictures in this manual may be the product you get will be different to you buy the real product 4 If in doubt please consult our company or dealer financing 2 1 Structure Gall indicat 0i EURT cpsprar SPT Charge GPS Indicator Indicator TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 f gt GPS antenna SHO PREO X Headphone 6PIN 4PINeO ai ARAA Interface 4PIN sintijit sien kee a SIM card slot USB Interface eject button 2 2 Specification GSM module MTK program GSM900 1800 850 1900 dual band or quad band Support the TCP protocol GPS Chipset JRC chipset GPS sensitivity 161dB C A Code 1 023MHz chip rate Channels 65 channel all in view tracking GPS frequency L1 1575 42MHz GPS Position Accuracy 2 5 meters CEP Velocity Accuracy 0 1m s Time Accuracy Synchronized to GPS time Cold Start 35sec average Hot Sta
22. T 1C a long time at rest then history will automatically shut down until the TLT 1C is awakened and opened the GPS 2 set of historical data upload instructions A From 24 hour history Instruction Format 808 user password 24 Example 808 0000 24 Note When receiving the order confirmation TLT 1C user password is correct return to sender confirmation message START UPLOAD 24H HISTORY RECORD Sent to the server while starting the last 24 hours recorded in historical data format and GPRS From time to time under the same model as shown in 3 2 16 the information in the state prompted the STORAGE B to read all the data records Instruction Format 808 0000 Description When receiving the order confirmation TLT 1C user password is correct return to sender confirmation message START UPLOAD ALL HISTORY RECORD Also sent to the server storage area began to record all the historical data as shown in formats such as 3 2 16 Information in the state prompted the STORAGE 5 1 14 Low voltage Upload When the TLT 1C working voltage when below the set value then regarded as 3 2 16 command processing and an increase in the data state LP key supporting TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 characterization of the current state Were made three times each time interval of 1 minute 5 1 15 Change the time zone settings instructions Command format 896 user password 4 D NN
23. TLT 1C User Manual GPS GSM Vehicle Tracker V1 8 2010 12 02 TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Product main features Real time SMS query coordinates time position Phone Position Remote monitoring capabilities active help feature speed alarm function historical data uploading Low power reminder running track monitoring 1 1 Introduction TLT 1C GSM GPRS Vehicle Locator is a remote location tracking device hereinafter referred to as TLT 1C is based on GPS technology and GSM GPRS technology made of Access to the user via SMS latitude and longitude location information and then in Google Maps or other mapping software to find the location tracking device or tracking device positioning data uploaded via GPRS to a designated server the user query through the Internet real time location tracking devices historical trajectory TLT 1C vehicle tracking devices mainly for logistics vehicles enterprises institutions and law enforcement duties of official vehicles bus scheduling and management 1 2 Features 1 Support GSM900 1800MHz 850 1900 optional to do Works worldwide Excellent for fixing the position even at a weak signal status work well even in areas with limited sky view like urban canyons 2 High sensitivity JRC low power GPS chipset 3 SOS button send out exact location for immediate rescue action Support check location and real time and historical trajectory by SMS or Internet
24. alist alarm 0 as a fence alarm Latitude and longitude values in degrees decimal point to be retained after five followed by zero can not be omitted I0 fences are out of the alarm I Finalist bar alarm 0 a fence alarm When the device receives the instruction to confirm the user password correctly the sender returns confirmation messages SET SQUARE GEO FENCE GX 10 I 0 OK Note 1 is set up automatically open the fence then the default fence type IO out of the fence are the police 2 If the calling state is off it will not make calls SMS mode only send messages to the user 3 The setting of this directive and the switch from power down effect of changes until you receive further instructions or reset operation 4 After reset the value of latitude and longitude marked with 0 Fence is turned off 2 1 gt Open rectangular electronic fence Open all rectangular electronic fence instruction format 311 user password Eg 3100000 Electronic fence off a single rectangular Format 310 user password GX Eg 3100000G5 Description This command is used to open all the electronic fence and open a single rectangular rectangular electronic fence GX means that an electronic fence X X range 1 16 When the device receives the instruction correctly recognized the user password to open the electronic fence sender rectangular return confirmation messages Open all rectangular electronic fence resume SET ALL SQUARE GEO FENC
25. ctively numbers and letters FTP server to clients on their own settings upgrade to the product documentation please consult your dealer TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 5 GPSR products online mode settings and advanced applications 5 1 1 Change Password command Command format 777 new password 4 Old Password 4 For example 77712340000 Description to confirm the old password is correct update the user password for the new user password set up after the success of confirmation to the sender to send a short message Content for the SET USER PASSWORD OK 5 1 2 GPS status is set to command Send SMS commands make GPS work in open close adaptive three states GPS factory set or reset for the normal open state l open the GPS instruction Instruction format 222 user password 4 For example 2 220 000 Description When the TLT 1C receiving the order confirm the user password is correct open the GPS power after the success of the sender to send the confirmation to the GPS ON OK 2 close the GPS commands Command format 333 User Password 4 For example 3 330 000 Description When the TLT 1C receiving the order confirm the user password is correct close the GPS after the success of the sender to send the confirmation to the GPS OFF OK 3 adaptive GPS instructions power function Commands 100 user password For example 1000000 Description When the TLT 1C recei
26. e opening that the second phase of 2 minutes ie Hzz Lyy you can set 3 99 When S is set to 0 then exit the power saving mode automatically switches to the GPS normally open mode that is 188 command will not work When the module receives the instruction to confirm the user password is correct according to the user to set parameters to configure the S L H items after the success to send the confirmation message GPS AUTO MODE yy zz xxx Minutes Note 1 Set S L H and other parameters if the high is 0 then we must make zero For example To turn off gps30 minutes will set the S030 but not set to S30 2 Hzz opened GPS to set the total time not less than Lyy TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 3 199 instruction set of the parameters are not lost restart the reset will not change until reset 4 Only in exceptional power saving mode the device can be set in accordance with the parameters of the timer switch 199 GPS other modes will not 2 Special power saving mode is on Instruction format 188 user password For example 1880000 Description 199 instruction set when the device is successful send 188 commands to take effect When you receive the confirmation code 188 instructions correctly to switch to GPS mode power saving mode the sender replies to the confirmation message GPS AUTO MODE ON OK After entering power saving mode the device 199 in accordance with the parameters set by inst
27. ehicle Tracker User Manual V 1 8 2 close the GPS commands Command format 333 user password 4 For example 3 330 000 Description When the TLT 1C receiving the order confirm the user password is correct close the GPS after the success of the sender to send the confirmation to the GPS OFF OK 3 adaptive GPS instructions power function command 100 user password For example 1000000 Description When the TLT 1C received the order confirm the user password is correct immediately close the sender GPS to send a confirmation SMS VIBRATION SENSOR ON OK Products built in vibration sensor once the monitoring of movement and change to the tracking devices to immediately open the GPS 5 minutes if there is no monitoring of changes to the tracking devices will automatically turn off sports GPS Note If the long flat roads or the highway GPS may be long dormant but will not be awakened If at this time to real time location tracking the user can send 222 user password to re open the GPS 4 GPS special power saving mode 1 Special power parameters Format 199 user password Xxx Lyy Hzz For example 1990000S030L01H03 Description S030 means that close GPS for 30 minutes and can be set 1 255 Open the GPS that the first phase of LO1 is 1 minute can be set 1 98 the first stage if the second stage is not positioned directly off GPS if not positioning the first stage the second phase H03 GPS represents the total time for th
28. example 8960000E08 Description One user password for the four D values of E W that the time zone thing NN is a two digit 1 12 that when code When the product after receipt of order confirm the user password is correct after the success of products set to sender send a confirmation SMS TIME ZONE SET OK CURRENT DN such as TIME ZONE SET OK CURRENT E8 Such as setting 8960000E08 set the time and after the success of all relevant data to the GPS receiver on the basis of time plus 8 set 896000W07 set the time and after the success of all relevant data to the GPS receiver based on the reduction of time 7 Default output Greenwich time if you set the parameters of NN for the 00 cases product recovery output GMT 5 1 16 Single Orientation return address instruction in Chinese Instruction format 1 667 user password for example 6670000 Instruction format 2 667 user password MAP example 6670000MAP Instruction format 3 667 user password MAP WWW HHH ZZ Example 6670000MAP 640 480 15 Description When device receives instruction 1 and confirm the correct user password immediately after reading the GPS information recognition information is valid send the address information to send the number of Chinese Such as King East Road Shenzhen Guangdong Poly Garden East Gate south 339 degrees east within a distance of 31 meters Send commands 2 will return a URL open the URL you can see the current location and a curren
29. f KM When the TLT 1C receiving the order to confirm the user password is correct to return to the sender to confirm the short message SET GEO FENCE OK and open the electronic fence function TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Instruction format 2 004 user password E Wddd dddddN Sdd ddddRzzz z For example 0040000E114 10004N22 55705R999 9 Description E E W W N north latitude S south latitude Used in this example is EandN please select the appropriate location according to the actual coordinates of format settings The meaning of the various parts of the sample as follows Eddd ddddd are degrees of longitude information which ddd ddddd that degree Decimal point behind the five followed by zero can not be omitted Ndd ddddd is a degree of latitude in units of information which dd ddddd that degree Decimal point behind the five followed by zero can not be omitted zzz z is the domain of radius 999 9 0 1 in units of KM When the TLT 1C receiving the order to confirm the user password is correct Return to sender confirmation short message SET GEO FENCE OK and open the electronic fence function Instruction format 3 005 user password Rzzz z Example 0050000R0 1 Description When the TLT 1C receiving the order to confirm the correct user password immediately after reading the latest GPS data and determine the validity of the second is for the A effective is the current latitude and
30. figure when XX is less than 60 its unit is minutes when XX Large at 60 its value is XX minus 60 the unit is the hour that is 61 to 1 hour 62 for 2 hours and so on When the TLT 1C receiving the order confirm the user password is correct TLT 1C set the current time as the initial time of time XX for the interval to confirm the sender s mobile phone to send text message TIMER START REPEAT INTERVAL lt X gt MINUTES Then start basic value of the initial time of time when the arrival time interval x x 3 1 1 format to send location information including information on status items automatically update STATE TIMER When XX is 00 the cancellation of regularly sending location instructions to confirm the sender s mobile phone to send text message TIMER STOP Note The current version of the maximum time interval can not exceed 2 hours For a longer time please let me company specially customized for you From time to time functional limitations by the GPS function when the GPS power saving features turned on GPS is in sleep mode at this time regularly uploading invalid and will not upload 4 1 4 Calling switch instruction Calling off instruction format 150 user password For example 1500000 calling open instruction format 151 user password For example 1 510 000 Description When the TLT 1C before calling the relevant instructions to confirm the user password is correct close the calling features including the SOS distress
31. function is turned on TLT 1C began to read the speed of GPS data and comparison with X real time If the GPS speed is greater than in X the instructions at this time for speeding TLT 1C No 3 stored immediately sent to a 3 1 1 format of location information the information in the status prompt for the STATE OVER SPEED speeding alarm if it detects the speed of GPS in less than X it indicates the speed at this time to return to a safe speed Under the driving TLT 1C immediately sent to the No 3 a 3 1 1 format stored location information the information in the status prompt for the STATE SAFE SPEED 4 1 10 Historical data uploading In SMS mode need to use this feature on the switch to GPRS mode on IP APN settings etc specific instructions and upload the data format please see the application of GPRS based operation l historical data records set command format 807 user password X Example 807 0000 30 Note X is a historical record of the sampling frequency an integer the domain of 0 999 unit is seconds When the TLT 1C receiving the order to confirm the user password is correct set the historical record of the sampling frequency is X If X 0 then close the historical data records if X 0 then the start time interval to X seconds for the GPS data received and stored after a successful return to the sender to confirm the information SET SAMPLING OK Note 1 each data record about 100B BYTE can
32. he client X 0 turn on the handset as the normal mode After the success the sender should send the confirmation messages SET PROFILE OK CURRENT PROFILE NORMAL If the stored user opens the handset phone call came in there will be a tone about 10 seconds after the automatic answer the two sides can make a call After the call to the call number location information sent 2 1 1 format which automatically updates the information state entries STATE ANSWEER Non stored phone number incoming call directly to hang up Note The factory set or reset state after the handset open non listening state 4 1 7 Active help feature Description When the long press SOS button more than 3 seconds immediately to the three phone numbers stored to send the location information such as 3 1 1 the information in the state prompted the STATE SOS Also call a telephone number stored in the first If unsuccessful shutdown or not connected then in turn call the second third If any of the stored numbers connected can remotely monitor Note If the calling state is off it will not make calls send text messages to pre existing users only TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 4 1 8Electronic fence function Electronic fence is to set the coordinates for the center of the circle set the radius to determine the scope of the fence When turned on set the fence after the TLT 1C beyond the scope of stored immediately after the No 3 sent
33. he confirmation message SET UNLIMITED MODE OFF OK Equipment can only receive 3 to play back the stored phone numbers non stored numbers hang up incoming calls directly without any treatment limit close calls when the device receives instructions to confirm the user password correctly to send a number reply to confirmation message SET UNLIMITED MODE ON OK Device can receive any phone call back the phone Note The factory set or reset state after the open 2 ACC status command prompt switch Open the command prompt ACC Status format 091 user password for example 0910000 ACC status prompted to close command format 090 user password for example 0 900 000 Description When the TLT 2H received 091 orders confirm the user password correctly send the confirmation to the sender Information ACC STATE PROMPT ON When the ACC in the on off switch text mode all stored numbers immediately to send the current location information regardless of GPS data is valid and AUTO START AUTO STOP as the opening ACC ACC switch off when the upload data state marked When TLT 2H received 090 orders confirm the user password correctly to send the confirmation message ACC STATE PROMPT OFF When the ACC in the on off switch whether it is GPRS mode or point to point mode TLT 2H will not send any data Note The default value is ON set the switch is not affected until you receive further instructions or reset changes to the relevant operation
34. he normal mode After the success the sender should send the confirmation messages SET PROFILE OK CURRENT PROFILE NORMAL If the stored user opens the handset phone call came in there will be a tone about 10 seconds after the automatic answer the two sides can make a call 5 1 6 instructions are treated as processing which automatically updates the information state entries STATE ANSWEER Non stored phone number incoming call directly to hang up Note The factory set or reset state after the handset open non listening state 5 1 10 Emergency upload Description When the regular press SOS button more than 3 seconds then regarded as 5 1 6 command processing the status prompt for the SOS Stored at the same time the first phone call if not successful or not turned off then in turn call the second third If any of the stored numbers connected can remotely monitor Note If the calling state is off it will not make calls only sending data to the server 5 1 11 Electronic fence function Electronic fence is to set the coordinates for the center of the circle set the radius to determine the scope of the fence When turned on set after the TLT 1C beyond the scope of the fence immediately sent to the server 3 2 16 format of location information Information in the state prompted to OS Also call a telephone number stored in the first If unsuccessful shutdown or not connected then in turn call the second third When the
35. lectronic fence X X range 1 16 When the device receives the instruction correctly recognized the user password to open the electronic fence sender rectangular return confirmation messages Open all rectangular electronic fence resume SET ALL SQUARE GEO FENCE OFF open a single rectangular electronic fence is SET SQUARE GEO FENCE GX OFF Note If you set multiple alarms occurred while rectangular enclosure the priority call G1 fence fence G2 G3 G4 only to send the relevant location information not make the call Factory configuration and reset the default state for the RS Attention Set of three ways of electronic fencing Choose one when the product after receipt of the electronic fence electronic fencing instruction set feature automatically opens When turned off the electronic fence is open again after the previous set are still valid 4 1 9 Speed alarm Instruction Format 122 user password X Example 122 0000 250 Note X is the speed reference value the data type integer in units of km hour KM H the domain of 0 999 When the TLT 1C receiving the order to confirm the user password is correct it will set the speed reference value X X 0 I close the speed alarm function X 0 speed alarm function is turned on after the success TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 of the first stored user to send a confirmation information SET RATE LIMIT X When the speed alarm
36. limit N S latitude lower Eg 0060000G1 I0 E114 10004N22 55705 E115 10006N23 55706 Note GX said the electronic fence X X range 1 16 IO fencing in and out of all alarms I selected as a finalist alarm 0 as a fence alarm Latitude and longitude values in degrees decimal point to be retained after five followed by zero can not be omitted I0 fences are out of the alarm I Finalist bar alarm 0 a fence alarm When the device receives the instruction to confirm the user password correctly the sender returns confirmation messages SET SQUARE GEO FENCE GX 10 I 0 OK Note 1 is set up automatically open the fence then the default fence type IO out of the fence are the police 2 If the calling state is off it will not make calls SMS mode only send messages to the user 3 The setting of this directive and the switch from power down effect of changes until you receive further instructions or reset operation 4 After reset the value of latitude and longitude marked with 0 Fence is turned fE 2 1 gt Open rectangular electronic fence Open all rectangular electronic fence instruction format 311 user password TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Eg 3100000 Electronic fence off a single rectangular Format 310 user password GX Eg 3100000G5 Description This command is used to open all the electronic fence and open a single rectangular rectangular electronic fence GX means that an e
37. locate will continue to open the GPS 2 4 H03 L01 2 minutes regardless of whether the GPS positioning all will be closed again for 30 minutes again and again Note 1 switch to power saving mode GPS work you must first set the command parameters 199 2 Open the power saving mode off the stage in the GPS GPRS sampling time and historical data are uploaded will stop in GPS positioning if the open stage GPRS uploaded regularly and historical data sampling will be back to normal 3 Open the power saving mode the GPS off stage whether text mode or GPRS mode the location information if the request operations such as 666 806 phone positioning SOS 4XX then the GPS would be immediately Open read the latest GPS data until the arrival of the next power cycle and then turn off GPS 4 If you need real time tracking please use the GPS normally open mode 5 1 3 Single positioning request instructions Command format 666 user password 4 Example 6 660 000 Description When the TLT 1C receiving the order confirm the user password is correct read the GPS information regardless of the validity of the original software set TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 it with the base station with return return to the sender Data format Lat latitude latitude value precision after the decimal point 5 Long longitude direction longitude value precision after the decimal point 5 Speed speed K
38. longitude information extracted coordinates of center of a circle as the fence and to R value of the radius while open electronic fence a successful return after the first sending confirmation SET GEO FENCE OK GPS data is invalid if the date is to give up continue to receive the next one if 50 seconds have not received valid data then return to the sender to send reminder ERROR GPS DATA TRY AGAIN LATER After the GPS set to resume their original state on off adaptive Note 1 fences can not exceed the radius of its domain the fractional part of the right to a value of zero must enter zeros For example R 1 must be entered as 1 0 2 if the calling state is off it will not make calls send text messages to pre existing users only 3 degrees and is divided into 60 binary conversion that 1d 60m TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 2 Open the e fence 211 user password When the TLT 1C receiving the order to confirm the user password is correct to open the electronic fence to return to the sender to confirm the short message GEO FENCE ON 3 Close E fence 210 user password When the TLT 1C receiving the order to confirm the user password is correct closed electronic fence to return to the sender to confirm the short message GEO FENCE OFF 2 gt set the rectangular range of the electronic fence Format 006 user password GX 10 1 0 E W longitude limit N S latitude limit E W longitude
39. ly remove the shift when the ACC switch to the off state by the opening the motion alarm feature will be on again When TLT 2H received 009 user password and verify the password is correct the motion alarm feature to be forced to close even if the ACC status changed from open to close the switch then move the alarm will not turn on again unless the re opening command to send 008 After the success to send a confirmation short interest has arisen MOVE DEFENGCE OFF 5 1 21 ACC function and state of charge detection switch 1 ACC charging detection TLT 2H detected by an external vehicle ACC ACC leads the state take the car to achieve ACC ON on the TLT 2H car battery built in battery charging parking ACC OFF the stop on the TLT 2H built in battery charger 5 1 23Automatic update instruction 1 the instruction format User password FTP address user name password 2 for example 0000 Igarin gicp net 123 0000 TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Description When the device receives the order confirmation password correctly and automatically restart FTP server address automatically log download When the update is successful will reboot again into normal use Note FTP address length 5 35 but also for domain names letters numbers dots Underscore _ and hyphen component User name FTP server user name a length of 3 20 password for FTP server password length 3 20 User name and
40. m the SMS and click the search button Google Maps will show you the location map For example When you receive the information transmitted from tracker as follows Lat 22 50500 Long 114 01000 Speed 0 OOKM H Direction 315 00 Date 2008 04 25 Time 16 39 45 BS 25ee0dff Fix A ID 353686009002030 STATE SMS Find locations in Google Maps enter in the appropriate location 22 50500 114 01000 Obtain the following picture TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 E Coerle arth Fis OR yw Tools acd bso Y Search _ ____ Fiy To Pins Gusrecens Orecterts Fly ioeo New rk NY 22 50500 114 01000 a ee ra Fist eect the Tay bution belowto stort gt im L tersperary Stecex this toleler andl click on Soe Prissy Detabase HA Be Geographic Web Cl E Rosse O 20 pradegs HEA F orders andi abet ro D trase GB vvestrar Point 12 31 21 82 114 01 5 60 ler 4m Streaming MEES Eyealt 6 7am 4 Or you can use the PDA or navigation device on a local map software enter the location data Note Note change in location data format ADE S25 gt pere Leen ar DLL KA Lanza O xru CEA Eid Re O ta 2 5t aimu tarpa peeta u pesoi TRIER ices R T Ais mi ARARIRE toian myrt neas aakgnr e Peete a pori im veka oa aa ssai TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 3 Single positio
41. mation is valid send the address information to send the number of Chinese Such as King East Road Shenzhen Guangdong Poly Garden East Gate south 339 degrees east within a distance of 31 meters Send commands 2 will return a URL open the URL you can see the current location and a current position of the shots screenshots default size is 240 320 EG http www gps069 com cngps mapaddr asp lng 114 09998 amp lat 22 55709 amp z 15 amp w 240 amp h 320 If you think the default screenshot is too small you can send commands 3 you can customize the size and scale the screenshot WWW is the width of the image HHH for the picture height ZZ for the zoom level Note WWW HHH s value is less than 1000 ZZ between the values proposed in the 1 20 adjust the ZZ can adjust the zoom level shots Such as http www gps069 com cngps mapaddr asp lng 114 09998k amp lat 22 55709 amp z 15kw 640 amp h 480 4 1 14 single shot positioning links to Google Maps to return instructions Instruction format 1 668 user password for example 6680000 instruction format 2 668 user password WWW HHH ZZ example 6680000 999 999 15 Description When the device receives the instruction 1 verify that the correct user password immediately after the read GPS information recognition information is valid send the current location of the Google Maps TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 screenshot of the website the screenshots
42. more than 300 new data will automatically overwrite the first backup data Note From time to time setting from Off to the impact of functional limitation but by the GPS power if power saving features turned on products in the power saving state to stop upload location data the GPS power saving features can be found in the following applications GPRS high level The details Do the three step basic setup you can operate in the service of products for you to monitor the platform to see their vehicle running track monitor the movements of the vehicle Advanced Applications 4 SMS point to point mode set projects and advanced applications 4 1 1 Change Password command Command format 777 new password 4 Old Password 4 For example 77712340000 Description to confirm the old password is correct update the user password for the new user password set up after the success of confirmation to the sender to send a short message Content for the SET USER PASSWORD OK 4 1 2 GPS status is set to command Send SMS commands make GPS work in open close adaptive three states GPS factory set or reset for the normal open state 1 open the GPS instruction Instruction format 222 user password 4 For example 2 220 000 Description When the TLT 1C receiving the order confirm the user password is correct open the GPS power after the success of the sender to send confirmation message to the GPS ON OK TLT 1C GPS GSM V
43. ning request instructions Product out of default mode in the SMS point to point if you want to switch to GPRS mode press the following command line operation GPSR online mode stored in the three phone numbers 1 2 3 and a 4 bit number of user passwords and do not change as the first step a group of TCP IP server IP address and port number 4 digit password and a GPRS GPRS access point APN number User defined text messages related configuration commands are non volatile content set after the success of the state machine switches from the impact of further changes until the receipt of the relevant instructions or reset operation GPRS online mode conversion Command format 710 user password 4 For example 7 100 000 Description When TLT 1C receive the SMS to confirm the user password is correct the switch to GPRS mode After the success of the sender to send confirmation message to the SET MODE OK CURRENT MODE GPRS The product location data uploaded to the Internet three major steps 1 set the GPRS Access Point Access Point Name Instruction format 1 803 user password APN example 803 0000 CMNET directive format 2 803 Password APN APN Username Password APN Note 1 different GSM GPRS service providers to offer a different APN please according to the local service provider s APN to choose to use the instruction format 1 or format 2 instruction set Note 2 When the TLT
44. ntrol reset only to send text messages do not make a call the deployment area and if it once again into the deployed area the location information will upload or send text messages and dial stored phone alarm which Information in the state marked as ACC RS Once the TLT 2H state is detected by the ACC switch to turn off after the alarm automatically remove the shift when the ACC switch to the off state by the opening the motion alarm feature will be on again When TLT 2H received 009 user password and verify the password is correct the motion alarm feature to be forced to close even if the ACC status changed from open to close the switch then move the alarm will not turn on again unless the re opening command to send 008 After the success to send a confirmation short interest has arisen MOVE DEFENGCE OFF 4 1 18 Automatic Update command Command format User password FTP address user name password for example 0000 Igarin gicp net 123 0000 Description When the device receiving the order to confirm the user password is correct the automatic restart and automatically log on FTP address of the server download When the update again after a successful reboot into normal use Note FTP address length 5 35 can also domain names letters numbers dot Underscore _ and hyphen form User name FTP server user name length 3 20 password for the FTP server password length 3 20 User name and password respe
45. o prevent the machine run out of battery 2 6 Wiring diagram Specific Application When you read the brief description of the product the product has been installed SIM card already installed Start following a specific use 1 11 First step a product owner stored telephone numbers and only had phone numbers stored the product will send you instructions to respond to other messages in order to work properly Products of the factory configured in the appendix Command as follows TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Instruction format New number 4 20 bit Password 4 number 1 3 For example 13900000000 0000 1 Note User initial password is 0000 TLT 1C can be stored up to three phone numbers When the TLT 1C receiving the order confirm the user password is correct with the new number to replace the existing number after the success of the sender to send the confirmation to the SET USER NUMBER 1 3 OK 1 2 Mode of introduction of products The product has two modes of the SMS point to point mode and GPRS online mode the user would like to use if necessary read the vehicle with a mobile phone ie products latitude and longitude map check with the Internet by phone control to control vehicle oil road leads off the point to point can be selected messages required dynamic real time monitoring of vehicles can use GPRS real time online mode Switching modes are as follows 2 Based on
46. ote WWW HHH these two values can not be greater than 1000 ZZ between the values proposed 1 20 when the device receives the command make sure the correct user password immediately after reading the GPS information recognition information valid send the current location of the Google Maps screenshot of the website you set the capture resolution of the resolution Screenshots URL example http maps google com staticmap center 22 554 765 174 10471 6 amp zo00m 6 amp size 24Ox24 0 amp ma ptype mobile amp markers 22 554765 114 104776 bluea amp sensor false amp hl cn 5 1 18 Single Location Google Maps link instruction to return Format 669 user password for example 6 690 000 Description When the device receives the command make sure the correct user password immediately after reading the GPS information recognition information is valid send the current TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 location of the Google Maps link to the number and user available through your PDA or smart mobile Internet Google Maps view in the current location URL Example http maps google com maps f q amp hl en amp q 22 554765 1714 104716 amp ie UTF amp amp z 6 amp iwloc addr amp om 7 Note The above three commands if sent in the past not on the server connection or other reasons not connected the reply 1 If the connection is not on the server the reply SEVER BUSY PLEASE TRY AGAIN LATER 2 If there is
47. pload data each time the Number N the domainof 1 50 When the TLT 1C receiving the order confirm the user password is correct send a confirmation to the sender short message SET GPS SAMPLING TIME AND QUANTITY OK Instructions specified in both the sampling interval T a continuous reading GPS NEMA data in the GPRMC statement and stored in memory When the number of articles stored on the user to set up the Number of N per upload began to connect GPRS server and the data sent If the network or other reasons due to the data is not sent to the server then automatically open the blind repay TLT 1C features that did not upload the data automatically backed up successfully when the network returned to normal after the replacement data to the server From the data format as shown in 5 1 6 the data in the state labeled AUTO When set to upload data each time the Number of N is 0 then close the regular upload send a confirmation to the sender SMS GPRS TIMER STOP Note 1 In order to increase product reliability is an order of work and timely response to users it is recommended to set the time do not upload more than 1 minute sampling TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 interval sample article that number is greater than 60 2 the settings are not regularly upload affected by the switch machine until once again received the relevant instructions to change or reset operation 3 blind repay up to 300 back up data
48. r password is correct close the calling features including the SOS distress power alarm calling fence alarm calling speed alarm etc after the success of the sender to send the confirmation to the SET VOICE CALL OFF When the TLT 1C before calling open order confirm the user password is correct open the calling features including the SOS distress power failure alarm calling fence alarm calling speed alarm etc after the success of the sender to send confirmation message to the SET VOICE CALL ON 5 1 8 Phone Upload Description When stored in one of three telephone calls come in to locate numbers and 2 5 in the sound of ringing after the hang then regarded as 3 2 16 command processing the status prompt for the CALL 5 1 9 Monitoring functions TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Instruction Format 00X user password for example 0000000 Description When the device user receives the order confirmation code correctly according to the value of X to set the handset switch state X 1 the handset closed the monitor mode After the success the sender should send the confirmation messages SET PROFILE OK CURRENT PROFILE SILENT Handset is turned off if the stored user phone calls in does not follow any prompts in about 10 seconds after the automatic answer the user can listen to the sound track side but the track side can not hear the voice of the client X 0 turn on the handset as t
49. racker User Manual V 1 8 667 Password Back to the Chinese position information 667 Password MAP Return address information plus screenshots Chinese 667 Password MAP WWW HHH ZZ Back to the Chinese address information plus screenshots screenshot to change the size and scale 668 Password Back to Google Maps Links Screenshots 668 Password WWW HHH ZZ Back to Google Maps screenshot link screenshot to change the size and scale 669 Password Back to Google Maps link 4xx Password 666 Password From time to time point to point mode Location to return a single user ID 777 New Password Old Password Change Password Stored number Password Serial number Change the stored number 8014 Password New User Change the GPRS user name 8024 Password new service password old service password GPRS service password change 8034 Password APNH GPRS access point settings 8034 Password APNHAPNUser name APNPassword GPRS access point settings 804 Password Fixed IP address and port Set IP address and port number 8054 Password Sampling intervall From the number of each clause N From time to time take the car to track mode settings 8064 Password Request From Single Location 8074 Password X Set the sampling rate history 8084 Password 24 From the historical data 24
50. rt lsec average TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Warm Start 25 sec average Altitude Limit 18 000 meters 60 000feet max Velocity Limit 515 meters second 1000knots max Acceleration Limit Less than 4g Operating temperature 20 C 65 C Humidity 5 To 95 Non condensing Dimension 95mm 53 5mm 26mm Voltage 12V 2 3 LED State Description Blue LED indicate the GSM signal state State Means constant Lighting no SIM card or not GSM net flashlight once interval 8s GSM receiver work well and standby Red LED indicate charge sate State Means constant Lighting charging No light charging was completed Green LED indicate the GPS signal state State Means No Lighting Working but no location Flashing Working and has located 2 4 Accessories 1 TLT 1C GPS GSM Vehicle Tracker 2 Power cord TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 3 GPS GSM antenna 4 Headphones 5 Battery 6 User s manual CD 2 5 Install SIM Card 1 Select SIM card e You can use GSM card from Local Mobile e Make sure enough deposit in the SIM card and support SMS GPRS function 2 Draw out the rear cover there is a slot for SIM card Then push the card into the slot until it fully inlays and ensure that it locks well Note SIM card slot is a power switch if long term non use please remove the SIM card slot t
51. ruction time switch GPS in order to achieve power saving purposes Such as setting 1990000S030L01H03 sending 188 to enter this mode the device according to the 199 instruction set turn off the GPS 30 S030 minutes and then open the 1 minute L01 if the GPS in the open for 1 minute L01 localization directly off GPS 30 4 S030 If a minute L01 did not locate will continue to open the GPS 2 4 HO3 L01 2 minutes regardless of whether the GPS positioning all will be closed again for 30 minutes again and again Note 1 switch to power saving mode GPS work you must first set the command parameters 199 2 Open the power saving mode off the stage in the GPS GPRS sampling time and historical data are uploaded will stop in GPS positioning if the open stage GPRS uploaded regularly and historical data sampling will be back to normal 3 Open the power saving mode the GPS off stage whether text mode or GPRS mode the location information if the request operations such as 666 806 phone positioning SOS 4XX then the GPS would be immediately Open read the latest GPS data until the arrival of the next power cycle and then turn off GPS 4 If you need real time tracking please use the GPS normally open mode 4 1 3 time to send location information instruction TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Instruction format 4 xx user password 4 For example 4010000 Description which is a 0 9 x that
52. store up to 3000 2 the data covered by the stack of records that way When the recorded data over 3000 the new data received will automatically overwrite the earliest recorded data 3 if the power saving feature is turned on and the TLT 1C a long time at rest then history will automatically shut down until the TLT 1C is awakened and opened the GPS 2 set of historical data upload instructions A From 24 hour history TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Instruction Format 808 user password 24 Example 808 0000 24 Note When receiving the order confirmation TLT 1C user password is correct return to sender confirmation message START UPLOAD 24H HISTORY RECORD Sent to the server while starting the last 24 hours recorded in historical data format and GPRS From time to time under the same model as shown in 3 2 16 the information in the state prompted the STORAGE B to read all data records Instruction Format 808 0000 Description When the TLT 1C receiving the order to confirm the user password is correct return to sender confirmation message START UPLOAD ALL HISTORY RECORD Also sent to the server storage area began to record all the historical data as shown in formats such as 3 2 16 Information in the state prompted the STORAGE 4 1 11 Low voltage alarm When the TLT 1C operating voltage lower than the set value read the GPS information regardless of the validity of
53. t position of the shots screenshots default size is 240 320 EG http www gps069 com cngps mapaddr asp lng 114 09998 amp lat 22 55709 amp z 15 amp w 240 amp h 320 TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 If you think the default screenshot is too small you can send commands 3 you can customize the size and scale the screenshot WWW is the width of the image HHH for the picture height ZZ for the zoom level Note WWW HHH s value is less than 1000 ZZ between the values proposed in the 1 20 adjust the ZZ can adjust the zoom level shots Such as http www gps069 com cngps mapaddr asp 1ng 114 09998 amp lat 22 55709 amp z 15kw 640kh 480 5 1 17 single shot positioning links to Google Maps to return instructions Instruction format 1 668 user password for example 6680000 instruction format 2 668 user password WWW HHH ZZ example 6680000 999 999 15 Description When the device receives the instruction 1 verify that the correct user password immediately after the read GPS information recognition information is valid send the current location of the Google Maps screenshot of the website the screenshots default resolution of 240 320 If you think that image is too small you can send commands 2 custom picture size in which the representative picture of the width of the WWW HHH on behalf of picture height ZZ for the zoom level you can set the size to comply with the resolution of your phone N
54. the three numbers stored immediately sent to the 3 1 5 format location information including information on status items automatically update STATE LP Were sent three times each time interval of 1 minute 4 1 12 change the time zone settings instructions Command format 896 user password 4 D NN Example 8960000E08 Description One user password for the four D values of E W that the time zone thing NN is a two digit 1 12 that when code When the product after receipt of order confirm the user password is correct after the success of products set to sender send a confirmation SMS TIME ZONE SET OK CURRENT DN such as TIME ZONE SET OK CURRENT E8 Such as setting 8960000E08 set the success of all data related to time received GPS time basis with 8 set 896000W07 set all the success and timing of the data received on the basis of time by GPS 7 Default output GMT if you set the parameters NN 00 cases the output product recovery GMT TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 4 1 13 Single Orientation return address instruction in Chinese Instruction format 1 667 user password for example 6670000 Instruction format 2 667 user password MAP example 6670000MAP Instruction format 3 667 user password MAP WWW HHH ZZ Example 6670000MAP 640 480 15 Description When device receives instruction 1 and confirm the correct user password immediately after reading the GPS information recognition infor
55. the user password correctly to send the confirmation message ACC STATE PROMPT OFF When the ACC in the on off switch whether it is GPRS mode or point to point mode TLT 2H will not send any data Note The default value is ON set the switch is not affected until you receive further instructions or reset changes to the relevant operation 4 1 17 ACC shift detection and alarm Shift alarm locale command 008 user password Rzzz z shift off the alarm command 009 with a password function When the TLT 2H received 008 user password Rzzz z command and verify that the password is correct set zzz z radius for the mobile alarm zzz z domain of 0 1 999 9 units of KM After the success returned to the sender confirmation message SET MOVE RADIUS OK After the success of mobile police locale if the ACC TLT 2H detected by the opening TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 switch to the off state then the delay of 3 minutes read the current location as the origin of coordinates regardless of the validity of gps data and zzz z as radius of the electronic area deployment In the ACC is off if TLT 2H beyond the deployment region is detected SMS mode the stored number immediately sent to a shift of all alarm messages status information is marked as STATE ACC OS GPRS mode immediately From the current location information server the status is marked as ACC OS and dial stored phone Whether by the 150 151 call co
56. uction format 2 004 user password E Wddd dddddN Sdd ddddRzzz z For example 0040000E114 10004N22 55705R999 9 Description E E W W N north latitude S south latitude Used in this example is EandN please select the appropriate location according to the actual coordinates of format settings The meaning of the various parts of the sample as follows Eddd ddddd are degrees of longitude information which ddd ddddd that degree Decimal point behind the five followed by zero can not be omitted Ndd ddddd is a degree of latitude in units of information which dd ddddd that degree Decimal point behind the five followed by zero can not be omitted zzz z is the domain of radius 999 9 0 1 in units of KM TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 When the TLT 1C receiving the order to confirm the user password is correct Return to sender confirmation short message SET GEO FENCE OK and open the electronic fence function Instruction format 3 005 user password Rzzz z Example 0050000R0 1 Description When the TLT 1C receiving the order to confirm the correct user password immediately after reading the latest GPS data and determine the validity of the second is for the A effective is the current latitude and longitude information extracted coordinates of center of a circle as the fence and to R value of the radius while open electronic fence a successful return after the first sending confirmation SET GE
57. vice password is correct Update Service password for new service password set up after the success of confirmation to the sender sends a short message CHANGE PASSWORD OK 5 1 6 From here instructions immediately Instruction Format 806 user password Example 806 0000 Description When TLT 1C receiving the order confirm the user password is correct the first stored number to send a confirmation SMS START GPRS UPLOAD sent to the server while the current store of data From the data in the state prompted for the TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 Ww SMS Ww Upload format IMEI number service password user name status data Base Station Information GPRMC Base Station Information GPRMC HA Such as 123456789000001 SR 6869BE 0000 SMS 3 25ee0dff GPRMC 083945 180 A 2233 4249 N 11406 0046 E 0 00 315 00 251207 A 6E 25ee0dff GPRMC 083950 180 A 2233 4249 N 11406 0046 E 0 00 315 00 251207 A 6E 25ee0dff GPRMC 083955 180 A 2233 4249 N 11406 0046 E 0 00 315 00 251207 A 6E HH Note The data format immediately upload status SMS 5 1 7 Calling switch instruction Calling off instruction format 150 user password For example 1500000 Calling open instruction format 151 user password For example 1 510 000 Description When the TLT 1C before calling the relevant instructions to confirm the use
58. ving the order confirm the user password is correct TLT 1C GPS GSM Vehicle Tracker User Manual V 1 8 close the GPS to the sender immediately send a confirmation SMS VIBRATION SENSOR ON OK Products built in vibration sensor once the monitoring of movement and change to the tracking devices to immediately open the GPS within 5 minutes if there is no monitoring of changes to the tracking devices will automatically turn off sports GPS Note If the long flat roads or the highway GPS may be long dormant but will not be awakened If at this time to real time location tracking the user can send 222 user password to re open the GPS 4 GPS special power saving mode 1 Special power parameters Command format 199 user password Xxx Lyy Hzz For example 1990000S030L01H03 Description S030 that off GPS 30 minutes and can be set 1 255 Open the GPS that the first phase of LOL is 1 minute can be set 1 98 the first stage if the second stage is not positioned directly off GPS if not positioning the first stage the second phase H03 GPS represents the total time for the opening that the second phase of 2 minutes ie Hzz Lyy you can set 3 99 When S is set to 0 then exit the power saving mode automatically switches to the GPS normally open mode that is 188 command will not work When the module receives the instruction to confirm the user password is correct according to the user to set parameters to configure the S

TLT-1C User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents