MA602X – JUPITER ORION Manual-E
Contents
1. i En Liquid detergents and soft cloth should be used DO NOT clean with acetone and ammonia detergents on fixtures Do not use detergents with formic acid or formaldehyde Do not use any abrasive cleaners Mineral deposits scaling on surface can be cleaned by soft cloth with heated vinegar After every 30 uses we suggest you to clean the steam generator Make a solution mixed with 1 5 1 7 liter of warm water and 5 10 grams of citric acid Or use straight white vinegar Pour the solution into the steam generator through the cleaning valve on the inside of the shower Turn it on after 8 to 10 hours wait for it to be discharged as steam General User s electric must meet national safety standard for voltage and frequency Power supply shall be consistent with the parameters marked on the product The ground should always be connected to the system We advise to use a water filtration system for the steam generator unit One Recommended filtration system is Whirlpool WHKF DWHV 12 Page BF1101 CONTROL SYSTEM FOR MA602X SERIES O DT Note Note Note Note Time 8 Temperature setting 11 Rainfall shower 12 Body Massage Jets 13 Top light 14 Time Temperature Increase 15 Time Temperature Decrease 16 Circulation Fan 17 Back light not active for this model 18 Sauna not active for this model 19 Radio on off and CD connection sauna key does not have any functions for this model Radio frequency Up2. the rainfall showerhead water line to faucet screw in Also connect the light fan and radio Then locate the middle water pipe which is under the faucet and connect it to the steam box water inlet Secondly connect the black steam line which is on the side of the steam box to the steam outlet Connect steam box drain line to the steam outlet drain Finally connect the cold and hot water lines to the water manifold the red one is for hot water while the blue is for cold A Steam outlet B Main Control box C Black steam hose insulated D Diverter E Rainfall shower head supply F Hose clamps G M4x25 screw H Hose clamp At this point you should have all electric amp water features connected M A6020 amp M A6023 ONLY Align glass E in slot of base align the installation holes of glass E to the holes of Glass D and Glass A Glass E has a black stripe long the top and side Use the Angle Bracket amp Connector Bolt apply connector bolt caps after final adjustments Attach the Door Panel G that has a black stripe along the top 16 17 18 MA6027 amp MA6028 ONLY Attach glass panel E which has a black stripe across the top and side to glass panel D and A and corner brackets on the left side of glass F will have holes for door hinge attach to panel D amp C with angle brackets and connector bolts Attach door hinges and door Panel G Put the wood floor grids in the s
3. Tempered Glass walls and front Clear Glass Y Y Unique Glass Touch Control Panel Y Y FM Radio Y Y Wireless transmitter optional extra transmits from any electronic device Y Y Hand held Remote control for entire panel control Y Y Chroma therapy LED multiple Color Lighting Y Y Waterproof Oak Shower Grid Y Y Removable Bench Y Y Circulation Fan Y Y Accessory Rack Y Y Phone Y Y Hinged door Y Y Stone composite base included Y Y Assembles from inside the unit Y Y Left Right Models Available Y Y Model Voltage Power Frequency Length Width Height MA6020 220V 3kW 50 60Hz 1090mm 43 Inch 800mm 31 5 Inch 2184mm 86 Inch MA6023 220V 3kW 50 60Hz 900mm 35 4 Inch 900mm 35 4 Inch 2184mm 86 Inch MA6027 220V 3kW 50 60Hz 1500mm 59 Inch 813mm 32 Inch 2184mm 86 Inch MA6028 220V 3kW 50 60Hz 1500mm 59 Inch 1016mm 40 Inch 2184mm 86 Inch 4 Page Rev 10 2012 PACKING LIST Glass angle bracket installation instruction Hinge installation instruction A Glass panel A Hinge B Threaded Connector 2 N B Glass door D o el C Angle Bracket hi A C Gasket i ae E af ED f C E Bolt cap er ie E Allen wrench A ro SECTION PICTURE OF RUBBER SEAL NS m TS SSL a A B VA N Y gt A l IA AGR OA e I yf A Half moon shape seal B Cornersea
4. Volume Increase Radio frequency Memory Steam ON OFF Radio frequency down Volume decrease Remote sensor Telephone Power on off Rainfall shower head and body jets are controlled by manifold only B light does not have any functions for this model Rainfall shower and body massage Jets are electronically controlled 13 Page DESCRIPTION OF FUNCTIONS Not in the same order above 1 10 ON OFF Key Under ON state press ON OFF Key on the panel to start the system and the top light is turned on all functions are activated on the panel the back light is on LCD shows the ambient temperature and all icons are lit press the ON OFF to shut off the system Press other keys except ON OFF key under standby and OFF state the backlight will come on if the systems is not turned on the backlight will be turned off in 30 seconds Following functions are available when the system is on Circulation Fan Press ED key on the panel to start the fan the icon will light up on the LCD screen Pressing the fan key again will shut down the circulation fan This function circulates the steam throughout the enclosed shower space No special exhaust needed for this function Steam Temperature and Time Setting Press TIME amp TEMPERATURE key on the panel so that temperature icon is on the screen system will enter into steam temperature setting state Press or key to increase or decrease temperature The t
5. ady 2 5 MIN ELECTRICAL INFORMATION 1 dedicated 12 2 line for steam line 1 line 2 and ground single phase three wire 220 volt 20 amp GFCI breaker The length of the wire for the machine is 1 5m adjustable it can be changed to a suitable length Connect the overhead light speaker fan CD telephone according to the tags on the wires Do not connect the wire O3 to anything Connect main power supply PLUMBING INFORMATION The unit is equipped with 3 ft hot and cold metal braided water supply hose with 72 inch national pipe thread to connect from faucet manifold Manifold is located 4 ft high on rear of unit to the shutoff valves should be installed where they can be accessed Note base edge sets directly against back and sidewall Do not install any pipes along walls as to impede the base from setting flush against them Install hot and cold shutoffs with inch male national pipe thread not included Install shutoffs where they can be accessible Access panel near controls pumps and jets is recommended Drainage It is advised to have base onsite before preparing drain location The diameter of the drain hole should be larger or equal to P40mm 1 6 inches Note The flexible drain hose included with this unit is for installation into a floor drain only substituting the existing drain setup for a setup of the installers choice will not void the warranty of the unit as long as there is no evidence of misuse or d
6. amage to the base All fixtures and fittings must be checked for tightness as they may have been loosened during transport GENERAL INFORMATION Caulk all needed seams and joints with 100 silicone caulk DRAIN INSTALLATION FOR ALL MODELS For glass steam room and shower room with 150mm shower tray A Glass A B Steam Generator Drain C Shower Drain D Shower tray Connect hot and cold supplies and make all electrical connections just before unit is set into place Units come broken down in panels and are assembled with screws nuts and bolts on site This unit assembles from the inside for convenience Note All shower bases are a man made stone composite and may need to be set in mortar for leveling purposes It is advised to have base onsite before preparing drain location Access panel area recommended Manufacturer reserves the right to change specs or features at anytime Please check to confirm details 1 866 783 2661 7 Page Rev 10 2012 INSTALLATION INSTRUCTIONS FOR MA6020 amp MA6023 Note Silicone joints amp seams where needed Note Determine the drain setup There needs to be a 3 8 inch diameter hose connected from the steam box to the main drain Place shower tray in the corner where it will be permanently located Note The handing R L of your unit determines which side the mounting plate goes ie A right handed unit has the mounting plate on the right 2 Make sure the installation holes for t
7. eaker tripped or damaged 1 Replace the circuit breaker or reset 2 Short circuit 2 Recheck the circuit 1 The intake valve or drain valve is damaged 1 Replace the intake valve or drain valve 2 The drain for the drain valve is jammed 2 Clear out the drain pipe Automatic shutdown 1 Electric components were damaged 1 Repair or replace the corresponding components 2 Electrical circuit is worn out 2 Replace circuit breaker 1 No water supply 2 Water pressure is too low 1 Wait for the water supply to start 3 The heating element of the steam generator is 2 Install Pressure pump damaged 3 Replace heating element No steam 4 No water in steam generator 4 Check the water intake valve 5 Steam pipe is jammed or broken 5 Clean out the jammed materials or replace the pipe 6 Heating time is not set 6 Set Steam timer 7 Temperature in the unit is higher than the set T Raise the temperature on the keypad remote steam temperature setting 1 Water pressure is too high 1 Lower water pressure 2 Intake valve or drain valve is jammed 2 Clear out jamming material in intake and drain valves 3 Drain pipes and drain is jammed 3 Clean out the drain pipe 4 Steam pipes are jammed 4 Clear out the steam pipes 2 Circuit board or the component is damaged 2 Replace circuit board Temperature is too 1 Preset temperature is too high 1 Adjust the temperature lower high 2 Temperature sensor is damaged 2 Replace the sensor 1 Pres
8. emperature range is 25 60 C 77 140 F press this key again to enter into time setting state The time range is 1 99 minutes If time or temperature is not adjusted within 5 seconds the system will automatically recover to display room temperature Steam Press key on the panel The default steam time is 45 minutes and the highest temperature is 45 C 113 F By pressing the steam key again the steam system will shut off CD FM Function Press Ka key on the control panel or remote to activate the FM Radio the corresponding icon will light up on the control panel The system will automatically switch to the previous frequency Pressing this key the second time will switch the function to CD mode The display will show the corresponding icon Pressing the a again will shut off the system Volume Adjustment When the speaker is ON pressing the or on the key panel to increase or decrease the volume When changing the volume the LCD monitor will display the corresponding changes tk Frequency or Channel Adjustment When the radio is ON press the TUN key to adjust the frequency radio channels Pressing the or button once will increase or decrease the frequency by 0 1MHz holding it for 1 minute will automatically search channels The search will stop once the next station is found and the LCD panel will display the corresponding channel When the system displays channel press or key t
9. ert the corner seal on the on the left side of glass B Note Attach glass shelf brackets to back of panel before proceeding 8 MA6020 MA60278 MA6028 NOTE Attach glass shelf brackets to the holes in glass B 9 Place the bottom edge of glass B into the slot on the base as shown below Align the holes and connect with angle brackets Connect to glass A 11 Insert the corner seal to the right edge of glass C then install angle brackets to the glass panel C Tighten snugly but leave enough tension to adjust Refer to picture below Install glass shelf brackets on panel C before moving forward SIT A w A j S Sin A PRA Place glass C into the slot onto the base and insert into the corner seal of glass B Note Glass B is the black panel and glass C is a black panel Line up the installation holes and connect glass B and glass C e Ae 4 AF u gt N an ys N N A JIS e SL 12 Assemble the half moon shaped seals on the sides a b and cof glass D top See illustration below Attach angle brackets to glass panel D 9 Page 19 Place glass D top on the top of the unit align connecting holes with glass D to glass panels A B and C Use M6X10 connector bolt to connect Please refer to illustration below Connect
10. et time ran out 1 Reset the time 2 Preset temperature is too low 2 Increase the temperature on keypad remote 3 Heating element is damaged 3 Repair or replace the heating element outlet 2 The water level circuit is not working 2 Check the water level circuit 1 No signal 1 Readjust for FM signal 2 Volume not high enough 2 Increase the volume 3 Speaker is damaged 3 Replace the speaker 4 Antenna is loose no signal 4 Connect the antenna and adjust the direction 5 Circuit board is damaged 9 Replace circuit board preu Circuit is loose or there is no contact 6 Re plug the circuit component or replace Check the control cable release and Peere Note aaa arrows and plug tightly Check the water level control cable between steam Water amp Drain Valve Water level control cable is not properly generator and the electrical box Release the screw problem connected and re plug in the head Automatic Protection Steam is Shutting off Audio not working Screen problem Screen problem Problem wih the contol cable with the control cable 16 Page 17 Page Oo STEAM PLANET 18 Page
11. he electric parts and the steam generator are lined up with installation holes connect it with M6X25 Hex bolts a H an 3 Insert the half moon shaped rubber seals shown in picture below onto the left right and top edge of glass A Glass 4 Main control panel Install angle brackets over the installation holes of glass A connect with connector bolts make the connection snug but loose enough to make adjustments Connector bolt caps will be installed when final tightening is complete Connect water supply lines and electrical lines Place bottom edge of glass A into the slot on the base as shown A small amount of soap or lubricant on the gaskets will help with installation Helpful hint install the shelf brackets to back panel before positioning in base See section 3 19 for more info 8 Page 6 The wires for the fan speaker and light are labeled Make the corresponding connections from the accessory to the wire coming from the control box Note Be cautious when making this connection The pins of the connector can easily bend if connected improperly A Wire for control panel B Temperature Sensor C Wire for speaker fan light D Speaker E Fan F Lights G Connecting terminal for light fan speaker H Control panel connecting terminal 7 Install the angle bracket to the holes on glass B black back panel Connect with screw Tighten snugly but leave enough tension to adjust Ins
12. hower tray and benches in the unit Attach flexible waterline to outlet on panel A and the other end to the handheld shower wand Attach to the bracket Note the hex nut of the water line goes on the panel outlet 10 Page 19 Attach handle to the door and shelves to panels B and 20 Steam Cup Connection Diagram A D N a H We gt A Steam outlet B Steam line Connector C Glass D Steam hose FAUCET FUNCTION AND USAGE e On Off Control o When the temperature is adjusted the water flow can be adjusted through the handle in the middle section o Clockwise turns on and counterclockwise turn off e Water Diverter handle o Turn the diverter handle according to the signs marked on its face e When you use the hand held shower turn the knob to the hand held shower sign e When you use the massage jets turn the knob to the back massage sign e When you use the rainfall shower head turn the knob to the rainfall shower sign e Cold Water and Hot o Turn the faucet to left and right to increase decrease the water temperature 11 Page CLEANING AND MAINTENANCE
13. imum of 3 9 higher than the height of the steam room 2 The water pressure has to be more than 3kg cm2 47 72 psi and if the pressure is lower than required you may install a booster to the water supply 3 Please use a 20 amp 220V GFI breaker for the electrical connection 4 We advised to have an access panel installed on the side of the electrical water connections for maintenance and service Manufacturer reserves the right to change specs or features at anytime Please check to confirm details 1 866 783 2661 PACKING NOTE 1 When first opening the boxes please make sure everything is in good condition especially if any visible damage has been done to the package please contact Steam Planet immediately with photographic documentation of the damage 2 Make sure all water and electrical components are up to local and national standards 3 Two installers are required for these units 4 Here are the tools you may need for installation lt X a a s F p Fi Rubber mallet wrench level tape measure screwdriver pencil 4mm allen wrench 3 Page Rev 10 2012 PRODUCT FEATURES DESCRIPTION MA6020 MA6023 3kW Quick heating Self Draining Steam Generator w Steam Aromatherapy Cup Y Y Multiple Body Massage Jets Y Y Hand held Shower w Various water massage settings amp adjustable height bracket Y Y 8 inch wide water drenching Rainfall Shower Y Y Thermostatic Anti scald Faucet Y Y Special Process Black
14. l C Magneticseal D Door bottom seal GLASS A Glass A Main Panel Black B Glass B Back Panel Black C Glass C Side Panel Black D Glass D Top Black E Glass E Front Clear Panel with Black Stripe F Glass F M A6027 6028 only Front clear Panel with Black Strip G Glass G Clear door black strip on top Diagram shows Right hand unit hinges are located on different side for different models 1 866 783 2661 Customer Service 5 Page Rev 10 2012 ROUGH IN DIAGRAMS Note All diagrams below are for right hand units only Please reverse for left hand units SER LTTE EEE ee an oe Abe O ee A ES ST er TA E SE M A6023 35 4x35 4x84in M A6020 43x31 5x84in lt A RRA RARA 2h PEbEBatEreas NAVA NAAA hs N WAAAY ANA AS PO SAALE ARRBERREREEC NURUURUEuuEt 000z 7 0001 M A6027 59x32x84in M A6028 59x40x84in IKW Rated voltage Rated power Rated frequency AC220V 50 60Hz x O oe amp a ee one wo L 9 o gL zZ O O O Ont Imo 6 Page Rev 10 2012 WATER AND ELECTRICITY INSTALLATION INSTRUCTION FOR ALL MODELS 1 Water Two water lines for cold and hot water respectively 72 inch National Pipe Thread NPT 2 Power Power requirement Single phase three wire 220V power supply TECHNICAL INFORMATION Materials Tempered Glass Power Supply 3KW 20amp 220V Steam Re
15. o adjust channels the range is 1 25 channels MEM HZ CH Selection Key When radio in ON press MEM key to select radio frequency H or channel CH Hold this key to store the correct frequency into channel LCD display will show MEM when stored Telephone Function Operational only when is plugged in or available When there is an incoming call telephone will ring system will automatically shut off the radio CD Press key on the panel to stop the ring and receive the phone call LCD display will show the telephone icon also the shower functions will automatically shut off Press phone key again to end the call You cannot dial out Mood Light Top light will turn on when the system is activated Press the Light key on the panel or remote control to turn on or turn off the mood light 14 Page MID 1101 REMOTE CONTROL SYSTEM Phone Note Sauna key does not have any functions for this model Note Rainfall shower head and body jets are controlled by manifold only Note B light does not have any functions for this model Note Rainfall shower and body massage jets are electronically controlled 15 Page TROUBLESHOOTING 1 Power line is not connected properly 1 reconnect the power supply 2 Insufficient power supply 2 Power supply must reach 50 60Hz 220V OSONA 3 Fuse is damaged 3 Replace the 2A fuse 4 Current circuit breaker is damaged 4 Replace the circuit breaker ie 1 Current circuit br
16. oc STEAM PLANET CONTEMPORARY STEAM ROOM Installation amp Operation Manual MA6020 MA6027 amp MA6028 Note You must read all installation amp operation instructions prior to assembly and use of this unit 1 Page Rev 10 2012 Table of Contents Notice to Installers 0 uensensssesssnessnesssneessnesssnensenensnnen ann 3 Packing Eist da 3 Product Features Chart sata 4 Packing List as 5 ROUGMEINDIAGIAM aire chet ca vet a aids et 6 Water amp Electric Requirements cs eecccceeccceceeeeeeeseeeeneeeeeeeesneeennens 7 Installation Instructions ui Oh tated ca enarbacat eames 8 11 Faucet Functions amp Usage a eeeeccccaesceceueeeeeaeeeccueeeeeaeeeeeneneeeaes 11 Cleaning Maintenance amp TiS haa eccccceccccseeeeceeeeeeeeeeeeeeeeeneeeesaeess 12 BF1101 Main Control Panel Diagram cooccccccccnccnccnccccnnconcnnnonononons 13 Description of Functions rra 14 MID1101 Remote Control een 15 IEFOUDIESNOOUNE alicia 16 Thank you for selecting Steam Planet Corp Computerized Steam Rooms In order to operate and use the product properly please follow all instructions provided in this User s Manual Our company reserves the right to change the Manual at anytime The manual takes effect the date it is published This manual shall prevail if there is any difference between this and previous documents and manuals 2 Page Rev 10 2012 NOTICE TO INSTALLERS 1 The distance from the ground to the ceiling has to be min
Download Pdf Manuals
Related Search