MPW 108 HP RGBW user`s manual
Contents
1. not only LED output but its life as well It is suggested to be cleaned by soft cloth with premium glass detergent instead of using alcohol or solvent X Danger Switch off power supply before any maintenance The front glass is easily stained by the draft of tobacco tar which will decrease light output so it should be cleaned once a week As for cooling fan once a month X There is not any repairable part inside the device except for fuse only franchisers have the right for maintenance X Change of Fuse When the bulb is burnt the fuse might also be burnt at the same time Only the fuse with same model and class need to be changed X Switch off power supply before changing fuse 10 Bgam opening m Beam opening Baam opening Beam opaning 2 CAUTION The guy who install it and maintain it you must follow Have the qualification of technician Follow the instruction Attention prevent water damp cut the power off when open the machine Keep Clear High Voltage the machine is in good condition before sell To confirm the safety please control it under the instruction The factory will not take responsibility 1f you don t control it under the instruction or change the machine personally or change the instruction casually Don t connect power wire with other wire confirm the power is available to the machine especially don t outstrip the power confirm plug connects with the power and the switch bu2. 5 no strobe You d better add second protection to avoid the shed of lose of the 196 255 fade out Io min to max speed 5 redR o0 100 spare parts cc 6 geen G 0 100 adjust brightness the light can be installed on the shelf as shown in illustration pT f blueb f 0100 adjust brightness Oeo whitetwy oo adjust rihin 9 E e a 10 000 004 no macro function 045 049 no function i gt D X 5 RGB macro i 4 Install The Equipment 191 202 blue green from bright to dark e il T A i 203 214 bluetred from dark to bright 215 226 red blue from bright to dark 227 238 red green blue from dark to brigh ae e 239 250 same time green from bright to dark 251 255 output 100 at the same time channel o 000 127 no fuction e mais e f e o a p13 oh i A o m il al a The strand wire is usually used in the shelf for the safety the strand wire should stand ten times weight than the machine You should use the stand wire which has safety lock pins the strand wire pass through the hole at the bottom and then tie it to the fixity Then tighten it 5 The Connect of Main Frame Confirm the power before connect European United states wire Line Mark Union wire Brown live line light blue null line yellow green earth wire use the plug to connect the machine to the power The connect of DMX 512 and lights Connect the XLR XLR control wire from DMX Pulse Output of the controller to t
3. CE LED Moving Head Light sing manual Read it carefully before use it 1 DISPACKING Thank you for using the products of our CO For your own safety please read this manual before installing the device This Manual covers the important information of installing and using Please install and operate following the manual book Meanwhile Please keep this manual well for using at any time Our moving wash is made of a new type of high temperature Strength of engineering plastics and cast aluminum casing from manufacturing design beautiful smooth fully embodies the characteristics of modern lighting products Products according to strictly CE standards of production design 1n full compliance with international standards DMX512 protocol single control and can also be controlled in group with each other suitable for large scale performances theater studio and places of higher Disco use The Moving head light adopt the powerful LED lamp which 1s import in the foreign country Once receive it please handle it carefully and check if there is some shatter because of Transportation and the following fittings are ok signal cable one Hook one Manual one 10 MAINTENANCE AND CLEANING This moving LED must be kept clean basically which means dust dirt or draft of tobacco tar should not be stayed on in the case otherwise it will sharply decrease the output of the moving LED Regular cleaning can guarantee
4. art it Caution when lens is damaged visible change to keep the previous effect It maybe injure the machine if it 1s controlled by the guy who is not professional lots of the damage 1s coming by this Use the original packing when delivery it Forbid change the machine unless approved The fault is not belonging to guarantee to keep in good repair if you don t control it under the instruction The short circuit damage accidental contact the damage by ultraviolet radiation the blow up all of this not belong to guarantee to keep in good repair 8 SKILL SPECIFICATION Light Source 3W LEDs LED Quantity 108 pcs Operation Modes DMX Master Slave Auto Sound DMX Channels 12 Connection DMX in out power cord in Beam Angle 10 40 Fixture Housing ABS Pan Tilt 540 230 IP Rating IP30 Dimensions W490mm L295mm H161mm Power Consumption 384W Weight 13 5 Kg 7 The Channel Horizontal scan 0 540 5 Bimer 6109 During installation please make sure no inflammable thing within 000 006 no strobe 0 5 t 007 065 strobe min to max speed 9 Meters 066 069 no strobe WARNING use the two hooks to fix the bottom of the machine and 070 128 Lightning Electromagnetic Pulse min Strobe 20 13 to max speed be sure the place where you installed is safe it can stand ten times no strobe adot mame weight than the light test that if the place is out of shape in one our 192 19
5. he light XLR connection o DMX output XLR plug seat 1 earth wire2 cathode 3 anode DMX plug 1 earth wire 2 cathode 3 anode Attention The last DMX Signal wire must connect to the loop plug seat pie a electric resistance of 120Q between the signal and signal of the plug then put them in the Pulse DMX Output of the last one faik i i iyi S REEN es ie SS Sig Bi n 1 GHD SE CREE im Signa TA LAM j Fk 2 E K K ein z H 6 Set of the display ATMALI ya press menu to back Pan inverter YES OR a press menu to back Ent id Pan angle ares Enter press menu to back L N rea Peete OR Ty press menu to back DMX 512 Firini press menu to back Enter DMX addre Enter up down Adress code Enter up down press menu to back Siave mode Enter sound mode press menu to back Enter auto mode press menu to back Enter Enter up down Enter up down Manually operate Manual Date xxx Choose channal Number of controlled Restore All the motor reset All the data change to original The display will close after 30 seconds no operation
6. tton is off before you connect with power Confirm the power wire is not puckered or damaged by the sharp check it once in a while Cut the power when it is not work or maintained When you cut off power pull up the plug not the wire to avoid the damage The level of protection is the first level connect the green yellow to the ground The connection and maintainment should be dong by the career man Don t connect the machine to the dimmer equipment Don t make on and off action frequently or the working life will become short It may be smelly when the first use it s the common To avoid hurting the eyes please do not look at the lamp house steadily Especially for the eye sicker 3 INSTRUCTIONS The machine is moving head light used to make the decorate effect Don t start the machine when its temperature changed drastically because the change of the temperature may damming the machine start it when temperature is in the common condition Be carefully for the shock when install Don t pull up the machine by the head of it this may damage it use the special tools to transport it The install place shouts not overheating over damp or too much dust don t put wire on the ground to avoid hurting any man At the button of this product there is a hole for safety wire please make sure that the safety wire is done with it When the machine 1s not installed or the screw is not tightening don t st
Download Pdf Manuals
Related Search