Specification of Battery Charger
Contents
1. Faktor technische Teile Professional Battery Charger manufacturer Ver 01 Faktor technische Teile FAKTOR GmbH Spinnereiinse 3D D 83059 Kolbermoor Tel 49 8031 2080023 Fax 49 8071 931272 www faktor de CLAY Ladegerate Specification of Battery Charger Model Number EJ21610LL LITHIUM BATTERY CHARGER Aluminum enclosure Doc No SPE BC 0143 Manufacturer reserves the right to alter or amend the approval sheet without the prior notice 1 5 Faktor technische Teile Professional Battery Charger manufacturer Ver 01 1 General Battery Charger EJ21610LL 340x220x116mm aluminum shell charger with reverse polarity protection function 2 Main product specification Combined Max output power Input voltage Output voltage Output current regulation 3 Environmental condition 4 Electrical characteristics 4 1 Input characteristic Rated input voltage 220Vac Input voltage range 189 264Vac AC input voltage frequency 50 60 Hz 4 2 Output characteristic or charge stages Z219Vac 108 2 3 CV constant voltage 219Vdc 10A ee Power efficiency Vin 110Vac rated load 4 3 Protection characteristics Software over The charger output voltage does not exceed set the maximum voltage charging voltage of the battery protection Aluminum shell the inside temperature gt 65 C Automatic Pe Manufacturer reserves the right to alter or amend the approval sheet without the prio2. he prior notice 4 5 Faktor technische Teile Professional Battery Charger manufacturer Ver 01 40 70 C the normal temperature 20 50 C and relative humidity is 5 95 In the warehouse there should not be harmful gas inflammable explosive products and corrosive chemical products and strong mechanical vibration shock and strong magnetic field affection The package box should be above ground at least 20cm height and 50cm away from wall thermal source and vent Under this requirement product has 2 years of storage period and should be rechecked when over 2 years 9 Reliability requirements MTBF standard environmental temperature load requirement 50K hours testing condition 25 C full load testing proved value 10 Charging Curve serene Voltage Current 13 MCC Time shut off point Manufacturer reserves the right to alter or amend the approval sheet without the prior notice 5 5
3. r notice 2 5 Faktor technische Teile Professional Battery Charger manufacturer Ver 01 protection Shutdown Transformer temperature gt 110 C Automatic Shutdown Current The charger output current does not exceed a set battery charge limiting current At CC mode protection EA ieej protection remove the condition Reverse When output wires are reversely connected to the battery the polarity charger will not operate and will work normally when DC wires E protection are correctly connected 4 4 Charging indicator Ne tem Same l Power on LED1 Red 2 Charging LED1 Red 3 Fully charged LED1 Red 5 Safety amp EMC Electric l 1500Vac Imin lt 10mA No breakdown strength test Input output Isolation Input ground gt 10Mohm 500Vdc 2 resistance Output ground gt 10Mohm 500Vdc asma LICE WURoHs UGS UUL LIccc LISAA LIPSE UKC EN55022 1998 A1 2000 A2 2003 EN55024 1998 A1 2001 A2 2003 EN61000 4 2 1995 A1 1998 A2 2001 EN61000 4 3 2002 EN6100 4 4 1995 A1 2000 A2 2001 EN61000 4 5 1995 A1 2000 EN61000 4 6 2001 EN61000 4 11 2001 Remark Discrimination A Function OK under technical requirement range Manufacturer reserves the right to alter or amend the approval sheet without the prior notice 3 5 Faktor technische Teile Professional Battery Charger manufacturer Ver 01 Discrimination R Physical damage or failure of equipment are not allowed but damage of protection device fuse caused by in
4. terference signal of outside is allowed and the whole equipment can work normally after replacement of protection device and reset of running parameter 6 Environmental testing requirements i High environmental l temperature ambient 40 C Features OK operating Low environmental 2 temperature ambient 10 C Features OK operating normally after recovery High temperature storage normal temperature for 2 Work normally after recovery Low temperature storage 40 C under normal temperature for 2 hours 7 to S500Hz Acceleration 6 Repetitive shock 10Hz to 60Hz Amplitude 0 38 Be 35 C to 75 C lt 3min transition 7 Thermal shock 2 5hours dwell 200cycle BS EN60068 2 32 1993 TEST Drop test ED free fall appendix B 7 Mechanical characteristic Shell material Aluminum Outline dimension L W H 340220x116mm Input socket meets IEC standard AC wires 1 5m length DC wire 1 5m length Net Weight 8 5Kg 8 Package transportation amp storage 8 1 Package There is product name model name of manufacturer safety approval serial number User Manual and packing list in the package box 8 2 Transportation Suit for transportation by truck the products should be Placed in cool dry place and loaded and unloaded carefully 8 3 Storage Products should be stored in package box when it 1s not used And Warehouse extreme temperatures should be Manufacturer reserves the right to alter or amend the approval sheet without t
Download Pdf Manuals
Related Search