Home

Specification - AL-KO

image

Contents

1. SAMSUNG SDI Confidential Proprietary PSamsungd Specification 1 Customer 2 Product Lithium ion Battery for power tool 3 SDI Model INR18650 13Q 4 Received Marking Division Signature Date ts 1l Lo 5 Date of Application YY MM DD 2007 6 Supplier SAMSUNG SDI Co Ltd Battery Division Issued Checked Approved H S SHIN Luis Cho Manager Senior Manager CSG Quality Assurance Samsung SDI Co Ltd Battery Division SAMSUNG SDI Confidential Proprietary PSamsungd SDI 1 Scope This product specification has been prepared to specify the rechargeable lithium ion cell cell to be supplied to the customer by Samsung SDI Co Ltd 2 Description and Model 2 1 Description Cell lithium ion rechargeable cell 2 2 Model INR18650 13Q 3 Nominal Specifications Item Specification 3 1 Nominal Capacity 1300mAh 260mA 2 5V discharge 3 2 Minimum Capacity 1250mAh 260mA 2 5V discharge 3 3 Charging Voltage 4 2 40 05 V 3 4 Nominal Voltage 3 6V 3 5 Charging Method CC CV constant voltage with limited current 3 6 Charging Current Standard charge 0 91A 3 7 Charging Time Standard charge 150min 3 8 Max Charge Current 4A ambient temperature 25 C o MAK Discharge Current 15A ambient temperature 25 C continuous 3 10 Max Discharge Current 30A 1sec Pulse 3 11 Discharge Cut off Voltage 2 5V 3 12 Cell Weight
2. in under table and 2 5V cut off after the standard charge Condition Note Percentage as an index of the capacity at 25 C 1250mAh is 100 SAMSUNG SDI Confidential Proprietary LED SDI 7 8 1 Cycle Life Each cycle is an interval between the charge charge current 1 3A with 100mA cut off and the discharge discharge current 10A with 2 5V cut off Capacity after 600cycles Capacity 750mAh 60 of the standard capacity at 25 C 7 8 2 Cycle Life2 Each cycle is an interval between the charge charge current 1 3A with 100mA cut off and the discharge discharge current 15A with 2 5V cut off Capacity after 350cycles Capacity 750mAh 60 of the standard capacity at 25 C 7 9 Storage Characteristics Capacity after storage for 30days at 60C from the standard charge measured with discharge current 4A with 2 5V cut off at 25 C Capacity retention after the storage 875mAh 70 of the capacity at 25 C 7 10 Status of the cell as of ex factory The cell should be shipped in 50 charged state In this case OCV is from 3 65V to 3 85V 8 Mechanical Characteristics 8 1 Drop Test Test method Cell as of shipment or full charged drop onto the oak board thickness 30mm from 1 0m height at a random direction 6 times Criteria No leakage 8 2 Vibration Test Test method Cell as of shipment is vibrated along 2 mutually perpendicular axes with total excursion of 1 6mm and with frequency cycling b
3. lead is welled 7 3 Transportation 7 3 1 If the cell is necessary to transported to order place such as the battery manufacturer careful precautions should be taken to avoid damage of cell 8 Others 8 1 Disassembly 8 1 1 The cell should not be dismantled from the battery pack 8 1 2 Internal short circuit caused by disassembly may lead to heat generation and or venting 8 1 3 When the electrolyte is coming in contact with the skin or eyes flush immediately with fresh water and seek medical advice 8 2 Short circuiting 8 2 1 Short circuit results in very high current which leads to heat generation 8 2 3 An appropriate circuitry should be employed to protect accidental short circuiting 8 3 Incineration 8 3 1 Incinerating and disposing of the cell in fire are strictly prohibited because it may cause rupture 8 4 Immersion 8 4 1 Soaking the cell in water is strictly prohibited because it may cause melt of components to damaged to functions 8 5 Mixing use 8 5 1 Different types of cell or same types but different manufacturer s cell may lead to cell rupture or damage to system due to the different characteristics of cell 8 6 Battery exchange 8 6 1 Although the cell contains no environmentally hazardous component such as lead or cadmium the battery should be disposed according to the local regulations when it is disposed 11 SAMSUNG SDI Confidential Proprietary en SDI 8 6 2 The cell should be disposed wit
4. 43 0g max 3 13 Cell Dimension Height 65 00mm max Diameter 18 40mm max Charge 5 to 40 C Discharge 20 to 60 1year 20 250 1 3 months 30 45C 1 1 month 30 60 C 1 Note 1 If the cell is kept as ex factory status 50 of charge 3 14 Operating Temperature 3 15 Storage Temperature the capacity recovery rate is more than 80 1 SAMSUNG SDI Confidential Proprietary PSamsungd SDI 4 Outline Dimensions See the attachment Fig 1 5 Appearance There shall be no such defects as scratch rust discoloration leakage which may adversely affect commercial value of the cell 6 Standard Test Conditions 6 1 Environmental Conditions Unless otherwise specified all tests stated in this specification are conducted at temperature 25 5 C and humidity 65 20 6 2 Measuring Equipment 1 Ammeter and Voltmeter The ammeter and voltmeter should have an accuracy of the grade 0 5 or higher 2 Slide caliper The slide caliper should have 0 01 mm scale 3 Impedance meter The impedance meter with AC 1kHz should be used 7 Characteristics 7 1 Standard Charge This Standard Charge means charging the cell with charge current 0 91A and constant voltage 4 2V 100mA cut off at 25 C 7 2 Standard Discharge Capacity The standard discharge capacity is the initial discharge capacity of the cell which is measured with discharge current of 4A with 2 5V cut off at 25 C within 1hour
5. after the standard charge Standard Discharge Capacity 1250mAh 7 3 Initial internal impedance Initial internal impedance measured at AC 1kHz after standard charge Initial internal impedance lt 30m2 7 4 Temperature Dependence of Discharge Capacity Capacity comparison at each temperature measured with discharge constant current 4A and 2 5V cut off after the standard discharge is as follows EL Ee kid ie SAMSUNG SDI Confidential Proprietary LED SDI Note If charge temperature and discharge temperature is not the same the interval for temperature change is 3 hours Percentage as an index of the capacity at 25 C 1250mAh is 100 7 5 Temperature Dependence of Charge Capacity Capacity comparison at each temperature measured with discharge constant current 4A and 2 5V cut off after the standard charge is as follows o a aes E Discharge temperature Relative Capacity E Note If charge temperature and discharge temperature is not the same the interval for temperature change is 3 hours Percentage as an index of the capacity at 25 C 1250mAh is 100 7 6 Charge Rate Capabilities Discharge capacity is measured with constant current 4A and 2 5V cut off after the cell is charged with 4 2V as follows Rod Charge Condition 100mA 100mA Relative Note Percentage as an index of the capacity at 25 C 1250mAh is 100 7 7 Discharge Rate Capabilities Discharge capacity is measured with the various currents
6. allow If younger children use the battery their guardians should explain the proper handling method and precaution before using Before using the battery be sure to read the user s manual and precaution of it s handling Before using charger be sure to read the user s manual of the charger Before installing and removing the battery from application be sure to read user s manual of the application Replace the battery when using time of battery becomes much shorter than usual Cover terminals with insulating tape before proper disposal If the battery is needed to be stored for an long period battery should be removed from the application and stored in a place where humidity and temperature are low While the battery is charged used and stored keep it away from object materials with static electric chargers Safety Handling Procedure for the Transporter E Quarantine Packages that are crushed punctured or torn open to reveal contents should not be transported Such packages should be isolated until the shipper has been consulted provided instructions and if appropriate arranged to have the product inspected and repacked E Spilled Product In the event that damage to packaging results in the release of cells or batteries the spilled products should be promptly collected and segregated and the shipper should be contacted for instructions Design of positioning the battery pack in application and charger To prevent the deterioration of t
7. code Marking there are three lines on the cell tube as follows Line 1 INR18650 13Q Cell Model Name Line 2 SAMSUNG SDI Cell Maker Line 3 076 642 Last 3digit means assembled date code Year 6 2006 Month 4 April Week 2 2 week E Lot Marking There are two lines on the cell metal can as follows Line 1 6086 1 digit line number 6 means Line No 2 2 3 digit Model Name 08 is INR18650 13Q 4 digit Year 6 is 2006 Line 2 4E1C5 1 digit Month 4 is Apr A is Oct Bis Nov C is Dec 2 digit Date E is 15 day 1 2 is 2 10 is A 11 is B 3 digit Serial No of winding 16 SDI SAMSUNG SDI Confidential Proprietary 4 digit Reel No C is C reel Ais A reel Bis B reel Fis Freel 5 digit Winding Machine No 1 is No 1 winder SDI
8. does not have should be conferred with between the both parties SAMSUNG SDI Confidential Proprietary LED SDI 12 Packing See Fig 2 Package Drawing Max 18 40 ENE A Max 65 0 Fig 1 Outline Dimensions of INRt865013Q SAMSUNG SDI Confidential Proprietary Tape Fa fc e SAMSUNG SDI Master carton 200PCS SAMSUNG SDI Confidential Proprietary LED SDI Proper Use and Handling of Lithium lon Cells See before using lithium ion cell Supplied by Samsung SDI Co Ltd 1 General This document has been prepared to describe the appropriate cautions and prohibitions which the customer should take or employ when the customer uses and handles the lithium ion cell to be manufactured and supplied by Samsung SDI Co Ltd in order to obtain optimum performance and safety 2 Charging 2 1 Charging current Charging current should be less than maximum charge current specified in the product specification 2 2 Charging voltage Charging should be done by voltage less than that specified in the product specification 2 3 Charging time Continuous charging under appropriate voltage does not cause any loss of characteristics However the charge timer is recommended to be installed from a safety consideration which shuts off further charging at time specified in the product specification 2 4 Charging temperature The cell should be charged within a range of specified
9. etween 10Hz and 55Hz by 1Hz min Criteria No leakage 9 Safety 9 1 Overcharge Test SAMSUNG SDI Confidential Proprietary LED SDI Test method To charge with 4A 10V at 25 C for 2hr Criteria No fire and no explosion 9 2 External Short circuit Test Test method To short circuit the standard charged cell or 50 discharged cell by connecting positive and negative terminal by less than 50mS wire for 10min Criteria No fire and no explosion 9 3 Reverse Charge Test Test method To charge the standard charged cell with charge current 10A By 12V for 2 5 hours Criteria No fire and no explosion 9 4 Heating Test Test method To heat up the standard charged cell at heating rate 5 C per minute up to 130 C and keep the cell in oven for 60 minutes Criteria No fire and no explosion 10 Warranty Samsung SDI will be responsible for replacing the cell against defects or poor workmanship for 15months from the date of shipping Any other problem caused by malfunction of the equipment or mix use of the cell is not under this warranty The warranty set forth in proper using and handling conditions described above and excludes in the case of a defect which is not related to manufacturing of the cell 11 Others 11 1 Storage for a long time If the cell is kept for a long time 3months or more It is strongly recommended that the cell is preserved at dry and low temperature 11 2 Other Any matters that specifications
10. h a discharged state to avoid heat generation by an inadvertent short circuit 8 7 Caution The Battery used in this device may present a risk of fire or chemical burn if mistreated Do not disassemble heat above 100 C or incinerate Replace battery with Samsung SDI battery only Use of another battery may present a risk of fire or explosion Dispose of used battery promptly Keep away from children Do not disassemble and do not dispose of in fire 8 8 Warning Attached Handling Precaution and Prohibitions of Lithium Ion amp Lithium Ion Polymer Rechargeable Cells and Batteries Inaccurate handling of lithium ion and lithium ion polymer rechargeable battery may cause leakage heat smoke an explosion or fire This could cause deterioration of performance or failure Please be sure to follow instructions carefully 1 1 Storage Store the battery at low temperature below 20 C is recommended low humidity no dust and no corrosive gas atmosphere 1 2 Safety precaution and prohibitions To assure product safety describe the following precautions in the instruction manual of the application Danger E Electrical misusage Use dedicated charger Use or charge the battery only in the dedicated application Don t charge the battery by an electric outlet directly or a cigarette lighter charger Don t charge the battery reversely EH Environmental misusage Don t leave the battery near the fire or a heated source Don t throw the battery
11. he battery performance caused by heat battery shall be positioned away from the area where heat is generated in the application and the charger Design of the Battery Pack 14 SAMSUNG SDI Confidential Proprietary PSamsungd SDI Be sure adopting proper safe device such as PTC specified type or model in Cell Specification If you intend to adopt different safety device which is not specified in Cell Specification please contact Samsung SDI to investigate any potential safety problem Be sure designing 2nd protective devices such as PTC amp PCM at the same time to protect Cell just in case one protective device is fault Please contact following offices when you need any help including safety concerns Samsung SDI Emergency Contact Information EH Samsung SDI Headquarter Samsung Life Insurance Bldg 150 Taepyungro 2 ga Jung gu Seoul Korea Tel 82 2 727 3686 Fax 82 2 727 3689 EH Samsung SDI Chonan factory 508 Sungsung Dong Chonan City Chungchongnam Do Korea Tel 82 41 560 3669 Fax 82 41 560 3697 EH Samsung SDI America office 18600 Broadwick Street Rancho Dominguez CA 90220 Tel 1 310 900 5205 Fax 1 310 537 1033 EH Samsung SDI Taiwan office Rm 3010 30F 333 Keelung Rd Sec 1 Taipei Taiwan Tel 886 2 2728 8469 Fax 886 2 2728 8480 SAMSUNG SDI Confidential Proprietary Additional Remark M Cell Package The bare cell is packed by which packaging material PET tube E Model and Date
12. into the fire Don t leave charge or use the battery in a car or similar place where inside of temperature may be over 60 C Don t immerse throw wet the battery in water seawater EH others SAMSUNG SDI Confidential Proprietary ET SDI shock Don t fold the battery cased with laminated film such as pouch and Polymer Don t store the battery in a pocket or a bag together with metallic objects such as keys necklaces hairpins coins or screws Don t short circuit and terminals with metallic object intentionally Don t pierce the battery with a sharp object such as a needle screw drivers Don t heat partial area of the battery with heated objects such as soldering iron Don t hit with heavy objects such as a hammer weight Don t step on the battery and throw or drop the battery on the hard floor to avoid mechanical Don t disassemble the battery or modify the battery design including electric circuit Don t solder on the battery directly Don t use seriously scared or deformed battery Don t put the battery into a microwave oven dryer or high pressure container Don t use or assemble the battery with other makers batteries different types and or models of batteries such as dry batteries nickel metal hydride batteries or nickel cadmium batteries Don t use or assemble old and new batteries together Warning Stop charging the battery if charging isn t completed within the specified time S
13. t generation and or rupture 6 4 Short circuit protection of the cell 6 4 1 The cell equips with an insulating sleeve to protect short circuit which may occur during transportation battery assembly and or system operation 6 4 2 If the cell sleeve is damaged by some cause such as outside impact it may cause short circuit with some wiring inside the battery 6 5 Connection between the battery and charger system 6 5 1 The battery should be designed to be connected only to the specified charger and system 6 5 2 A reverse connection of the battery even in the specified system should be avoided by employing special battery design such as a special terminals 6 6 Pack design 6 6 1 The battery pack s current consumption should be under 10uA at sleep mode 6 6 2 Cell Voltage monitoring system The system Charger or Pack should equip with a device to monitor each Cell voltage and to stop charging if cell imbalance happen 6 6 4 The battery pack should have warning system such as over temperature over voltage over current and so on 7 Battery Pack Assembly SAMSUNG SDI Confidential Proprietary PSamsungd SDI 7 1 Prohibition of usage of damaged cell 7 1 1 The cell should be inspected visually before battery assembly 7 1 2 The cell should not be used if sleeve damage can distorsion and or electrolyte smell is detected 7 2 Terminals handling 7 2 1 Excessive force on the negative terminal should be avoided when external
14. t period after charging because long term storage may cause loss of capacity by self discharging 4 2 2 lf long term storage is necessary the cell should be stored at lower voltage within a range specified in the product specification because storage at higher voltage may cause loss of characteristics 5 Cycle life 5 1 Cycle life performance 5 1 1 The cell can be charged discharged repeatedly up to times specified in the produce specification with a certain level of capacity also specified in the product specification 5 1 2 Cycle life may be determined by conditions of charging discharging operating temperature and or storage 6 Design of System SAMSUNG SDI Confidential Proprietary PSamsungd SDI 6 1 Connection between the cell and the battery 6 1 1 The cell should not be soldered directly with leads Namely the cell should be welded with leads on its terminal and then be soldered with wire or leads to soldered lead 6 1 2 Otherwise it may cause damage of component such as separator and insulator by heat generation 6 2 Positioning the battery in the System 6 2 1 The battery should be positioned as possible as far from heat sources and high temperature components 6 2 2 Otherwise it may cause loss of characteristics 6 3 Mechanical shock protection of the battery 6 3 1 The battery should equip with appropriate shock absorbers in order to minimize shock 6 3 2 Otherwise it may cause shape distortion leakage hea
15. temperatures in the product specification 2 5 Reverse charging The cell should be connected confirming that its poles are correctly aligned Inverse charging should be strictly prohibited If the cell is connected improperly it may be damaged Fig 2 Package Drawing 3 Discharging SAMSUNG SDI Confidential Proprietary Psamsungd SDI 3 1 Discharging 3 1 1 The cell should be discharged at less than maximum discharge current specified in the product specification 3 2 Discharging temperature 3 2 1 The cell should be discharged within a range of temperatures specified in the product specification 3 2 2 Otherwise it may cause loss of characteristics 3 3 Over discharging 3 3 1 The system should equip with a device to prevent further discharging exceeding discharging cut off voltage specified in the product specification over discharging 3 3 2 Over discharging may cause loss of performance characteristics of battery function 3 3 3 Over discharging may occur by self discharge if the battery is left for a very long time without any use 3 3 4 The charger should equip with a device to detect cell voltage and to determine recharging procedures 4 Storage 4 1 Storage conditions 4 1 1 The cell should be stored within a range of temperatures specified in the product specification 4 1 2 Otherwise it may cause loss of characteristics leakage and or rust 4 2 Long term storage 4 2 1 The cell should be used within a shor
16. top using the battery if the battery becomes abnormally hot order discoloration deformation or abnormal conditions is detected during use charge or storage Keep away from fire immediately when leakage or foul odors are detected If liquid leaks onto your skin or cloths wash well with fresh water immediately If liquid leaking from the battery gets into your eyes don t rub your eyes and wash them with clean water and go to see a doctor immediately If the terminals of the battery become dirty wipe with a dry cloth before using the battery The battery can be used within the following temperature ranges Don t exceed these ranges Charge temperature ranges OC 45C Discharge Temperature ranges 20 C 60 Store the battery at temperature below 60 C Cover terminals with proper insulating tape before disposal Caution E Electrical misusage Battery must be charge with constant current constant voltage CC CV Charge current must be controlled by specified value in Cell specification 13 SAMSUNG SDI Confidential Proprietary LED SDI Cut off Voltage of charging must be 4 2V Charger must stop charging battery by detecting either charging time or current specified in Cell s specification Discharge current must be controlled by specified value in Cell s specification Cut off Voltage of discharging must be over 2 5V E others Keep the battery away from babies and children to avoid any accidents such as sw

Download Pdf Manuals

image

Related Search

Related Contents

VIAFLO ASSIST Bedienungsanleitung  installation/operations manual  PCCtest 170 User`s Manual Preliminary  2013 年 2 月  2015 年 4 月  washeruserinstructions instruccionesparaelusuariodelalavadora  Wentronic Bluetooth Headset stereo (Calypso)  Samsung Galaxy Note Kasutusjuhend(Ice Cream Sandwich)  

Copyright © All rights reserved.
Failed to retrieve file