Specification of Battery Charger
Contents
1. SONEIL 6033 Shawson Dr Unit 29 Mississauga Ontario Canada L5T 1H8 Ph 905 565 0360 Fax 905 565 0352 http www soneil com Revision No R02 Specification of Battery Charger MODEL 1240 SR 12V 20A LEAD ACID BATTERY CHARGER Subject to change without prior notice please feel free to contact us for latest information l General Battery Charger 1240SR is cooled by 250 150 88mm 12VDC ball bearing fans with forced air can work normally under 14 7Vdc 20A and with reverse polarity protection 2 Main product specification Input voltage Output voltage Combined regulation 305W 115Vac 230Vac 14 7 0 2Vde 19 5 20 5A 0 2V 3 Environmental condition Humidity With package 3 Cooling The power supply is cooled by 250 150 88mm Working under full 12VDC ball bearing fans forced air load 4 Electrical characteristics 4 1 Input characteristic 4 2 Output characteristic a Fest charge volige raras Jooo 2 Floating voltage ve oS S constanter EVI E 4 3 Protection characteristics Software over voltage protection The charger software limits the maximum output voltage to a level suitable for the connected battery system Thermal protection An internal temperature monitor reduce charger output power in extreme operational temperature to prevent damage Current limiting protection 22A At CC mode Short circuit protection Short circuit protection should be automatically recovery2. 14 0V and current of 50 100mA signal to the controller When controller is connected to inhibit wire it will shut off the electric circuit of the vehicle and prevents vehicle from moving during charging 11 Label PATENT PENDING MODEL 12405R www sonell com AC Input Charging Indicator DC Output Wire SONEIL CANADA r 905565 0360 Pe Fax 905 565 0352 E x Caution Risk of electric shock Do not expose to liquid vapor or rain Charge only lead acid type rechargeable batteries Other types 115 230V AC 60 50Hz LED1 Red Power On Brown wire DC E RSE AVES personal injury and damage Max Input Current LED2 Off Charging with Blue wire DC SIOW BIOW use 3 6A at 90Vac input current reading on 5 DC Output multimeter display Serial No A AN ia fn 12V 20 0A Constant Uy UY 12 Charging Curve Refer to attachment
3. after remove the condition Reverse polarity protection If output wires are reversely connected the charger will not operate and will work normally when wires are correctly connected 7 Fan cooling The fan is controlled by a temperature sensor After charger works the fan will run for 2min or so even several seconds if the charger temperature is below 30 45 C the fan will stop 1f the charger temperature rise the fan will run again 4 4 Charging indicator C e e A Cragin 1777 AN Fuy tel a O a Charge voltage CD display Select switoh at V positon Standard or test condition Remark l Electric Input output 1500Vac 10mA 1min No breakdown strength test IN EMC EN55022 1998 A 1 2000 A2 2003 EN55024 1998 A 1 2001 A2 2003 EN61000 4 2 1995 A1 1998 A2 2001 EN61000 4 3 2002 EN6100 4 4 1995 A 1 2000 A2 2001 EN61000 4 5 1995 A 1 2000 EN61000 4 6 2001 EN61000 4 11 2001 EN60335 1 2002 EN60335 2 29 2002 Remark Discrimination A Function OK under technical requirement range Discrimination B Function temporarily debasement without reposition and halt 1s allowed Discrimination R Physical damage or failure of equipment are not allowed but damage of protection device fuse caused by interference signal of outside s allowed and the whole equipment can work normally after replacement of protection device and reset of running parameter 6 Environmental testing requirements O l High tempe
4. hould be above ground at least 20cm height and 50cm away from wall thermal source and vent Under this requirement product has 2years of storage period and should be rechecked when over 2years 9 Reliability requirements MTBF standard environmental temperature load requirement gt 50K hours testing condition 25 C full load testing proved value 10 Charger wiring 10 1 A spark often on first connection of the charge to the battery terminals due to charging the internal output capacitors this is normal and should not lead to undue concern care should be taken to ensure the battery vent caps are closed and there are no flammable object in the vicinity of where the connection will be made 10 2 The charger has been calibrated to take account of the voltage drop in the DC output cables during operation to prevent the possibility of over or under charging of the battery it is recommended the DC output cable are connected directly to the battery without modification We are able to customize cable length and connections for volume customers with specific requirements 10 3 The inhibit wire cannot be tested or connected to the output and the output wires it supplies power for the controller such as a relay After the inhibit wire is connected to the controller terminal and the charger output connected to the controller terminal the controller will work The inhibit wire provides a DC voltage of 13 7V
5. rature 40 C Features ok 2 Low temperature 10 C Features ok I 3 High temperature 70 C Work normally after recovery under Fr Pepa dl 4 Low temperature 40 C Work normally after recovery under feng con Repetitive shock 40g peak 3 orthogonal axes 3 and 3 BE 7 Thermal shock 35C to 75C lt 3min transition anatase Drop test BS EN60068 2 32 1993 TEST ED free BE FF 7 Mechanical characteristics 20Hz to 2000Hz 3Grms 20hours per axis Outline dimension L W H 250 150 88mm Input socket meets IEC standard Output wire LOAWG 4mm brown ve amp blue ve 1 5m length thick insulation Inhibit voltage wire AWG18 yellow 1 5m length Weight 3 6Kg oe ra sj AN A Z lti N lt 8 Package transportation amp storage 8 1 Package There is product name model name of manufacturer safety approval serial number User Manual and packing list in the package box 8 2 Transportation Suit for transportation by truck ship and plane the products should be shielded by tent from sunshine and loaded and unloaded carefully 8 3 Storage Products should be stored in package box when it is not used And warehouse temperature should be 40 70 C and relative humidity is 5 95 In the warehouse there should not be harmful gas inflammable explosive products and corrosive chemical products and strong mechanical vibration shock and strong magnetic field affection The package box s
Download Pdf Manuals
Related Search