User Manual
Contents
1. Green LED indicate the GPS signal state State Means No Lighting Working but no location Flashing Working and has located 49 Products Appendix 1 TLT 2H GPS GSM Vehicle Tracker 2 Power cable 3 Battery 4 User Manual CD ROM SO SOS Button 5 Install SIM Card 1 Select SIM card 2 You can use GSM card from Local Mobile 3 Make sure enough money in the SIM card and support SMS GPRS function 4 Draw out the rear cover there is a slot for SIM card Then push the card into the slot until it fully inlays and ensure that it locks well 6 Installation DO agrane The external 5 wires of TLT 2H GPS GSM tracker are as follows Red for the 12V car power wire connect to the car battery anode Black for the earth GND connect to the car battery cathode Yellow for the SOS for help Control wire connect external SOS switch button to car battery cathode Green wire connect ACC car power supply that is with the car CD radio and other automotive electrical appliances in parallel When the vehicle key puts in the ACC gear the green line will examine the 12v voltage the terminal will open the charge function automatically White for cut off oil and power control wire connect to the relay coil 86 i e one end Relay 85 i e anther end connects to oil and power supply 12V 30 87a are normal closed end series in the oil and power supply circuit Please note that if the installation of lead2. 3 1 Open the GPS instruction Format 222 user password 4 figures eg 2220000 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly opens the GPS power After the success it will send the confirmation messages GPS ON OK to the sender 3 2 Close GPS instruction Format 333 user password 4 figures eg 3330000 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly close the GPS After the success it will send the confirmation messages GPS OFF OK to the sender 3 3 Adaptive GPS instruction Power saving Function Format 100 user password 4 figures eg 1000000 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly it will close the GPS immediately and send the confirmation messages VIBRATION SENSOR ON OK to the sender The tracker built in vibration sensor once monitors the track movement for change to open the GPS If in 5 minutes with not monitors the track changed in the movement to close GPS Note If a long time on the highway or the flat road the GPS may be in sleeping and will not be awakened Users can send 222 user passwords to re open the GPS 4 Single localization request instruction Format 666 user password 4 figures eg 6660000 23 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly reads the GPS informa
3. command 18 ACC Checking and Alarm for Moving Alarm Command for Moving 008 Password Rzzz z Close Alarm Command for Moving 009 Password Note when TLT 2H receive 008 command and confirm the password is correct put Rzzz z for the radius of area the zone of zzz z is 0 1 999 9 the unit is KM after configuration is ok TLT 2H will send SET MOVE RADIUS OK to the sender After configuration of the alarm for moving is complete if TLT 2H checking the ACC State is changed which from ACC ON to ACC OFF after three minutes the TLT 2H will take the current position for the coordiration point the unit will open the defence use the zzz z whether the GPS Data is Available or Valid when the ACC is OFF if TLT 2H checking the car over the defence in the SMS Mode the TLT 2H will send a message to the pre saved numbers what the state is STATE ACC OS the unit will send the current position to the server the state is ACC OS and call the pre saved numers the 150 151 comamnd will affect the unit that whether call the pre saved numbers if you reset the unit the unit will only send message and don t call numbers once the car coming the defence the unit will send current position information to the server or send message and call the pre saved numbers and the state is ACC RS Once TLT 2H checking the ACC state is close from Open to Close the Alarm for Moving will close automatically when the ACC state is open from Close to open the
4. when the car is moving and the power of the car will recharge to the unit and the ACC Off when 31 the car is parking and the power of the car will not recharge to the unit 3 The On Off Command for ACC State Open Command of ACC State 091 Password Eg 0910000 Close Command of ACC State 090 Password Eg 0900000 Note when TLT 2H receive the 091 command and confirm the password is correct TLT 2H will send a message to the sender what the content is ACC STATE PROMPT ON when ACC is ON OFF the TLT 2H will send the current position to the pre saved numbers whether the GPS Data is avaible or valid and the state will display AUTO START AUTO STOP be the ACC State when TLT 2H receive the 090 command and confirm the password is correct TLT 2H will send a message to the sender what the content is ACC STATE PROMPT OFF when ACC is ON OFF the TLT 2H will not send any message whatever the unit is GPRS Or SMS Mode Attention the default is ON and once the configuration is ok whatever the unit is ON OFF the unit will not change until receve the next command or reset command 20 ACC Checking and Alarm for Moving Alarm Command for Moving 008 Password Rzzz z Close Alarm Command for Moving 009 Password Note when TLT 2H receive 008 command and confirm the password is correct put Rzzz z for the radius of area the zone of zzz z is 0 1 999 9 the unit is KM after configuration is ok TLT 2H will send SET MOVE RA
5. 37 ILI 2H Ricture 3 1 Specification GSM GPS Power GSM module MTK Case support 900 1800 850 1900 can option Support the TCP protocol GPS Chipset JRC chipset GPS sensitivity 164dB C A Code 1 023MHz chip rate Channels 210 channel all in view tracking GPS frequency L1 1575 42MHz 3 2 Others GPS Position Accuracy 2 5 meters CEP GSM Position Accuracy Later will realize Velocity Accuracy 0 1m s Time Accuracy Synchronized to GPS time Cold Start 35sec average Hot Start lsec average Warm Start 30sec average Altitude Limit 18 000 meters 60 000feet max Velocity Limit 515 meters second 1000knots max Acceleration Limit Less than 4g Operating temperature 20 C 65 C Humidity 5 To 95 Non condensing LED Dimension 88mm 46mm 18mm Voltage 12 24V Average Current When stand by lt 84mA Green Blue Red LED showing GPS GSM and power status Out set SOS Key One SOS emergency key for urgent call 3 3 LED State Description Blue LED indicate the GSM signal state State Means constant Lighting no SIM card or not GSM net flashlight once interval 8s GSM receiver work well and standby flash quickly voice calls or in GSM connection Red LED indicate charge sate State Means constant Lighting charging No light charging was completed
6. Alarm for Moving will open automatically When TLT 2H receive 009 Command and confirm the password is correct the Alarm for Moving is closed automatically whatever ACC State is open or close unless send 008 command again after you set 009 command the utni will send MOVE DEFENGCE OFF to the sender 19 Attention the Alarm for Moving of default is open and the area is 5 00M 19 Updata on the Air 1 Formate Password Eg 0000 Note when TLT 2H receive this command and confirm the password is correct the unit will restart and enter FTP Server to download procedure automatically after succesful the unit will restart again and it s ok 2 Formate Password FTP Address User Name Password Eg 0000 igarin gicp net auto 123 Note when TLT 2H receive this command and confirm the password is correct the unit will restart and enter FTP Server to download procedure automatically after succesful the unit will restart again and it s ok Attention the area of FTP Address is 5 35 and also can use domain and made is for characters numbers U the user name is for FTP the area is 30 20 the password is FTP S password the area is 3 200 GPRS Work Mode The way of change mode please check the instruction In GPRS Mode can save three numbers 1 2 3 and a password 4 digits a group TCPIP IP and Port a GPRS Service Password a APN Number The configuration command is not effect whether the
7. DD Time Time HH MM SS GMT BS Base Station information Fix Location state A V ID IMEI STATE Message state Effective data format Lat 22 50500 Long 114 01000 Speed 0 00KM H Direction 315 00 Date 2008 04 25 Time 16 39 45 BS 25ee0dff Fix A ID 353686009002030 STATE SMS Invalid data format Lat 22 50500 Long 114 01000 Speed 0 00KM H Direction 315 00 Date 2008 04 25 Time 16 39 45 BS 25ee0dff Fix V ID 353686009002030 STATE SMS Note If in the cold start and GPS no position it will return to the void of information eg ERROR GPS GPRMC FRAME DATA BS 27971054 ID 353686009002030 STATE SMS Display the location on map 1 Download Google earth software from http earth google com 2 Start the Google earth software For more information about Google earth software please refer tohttp earth google com Sct Eee er en Ot be a i Zso Gr ges Ioano Pte rounarens onsen UME y cael i ee Pyare arnsceew TR lt 4 oS i UDDURAN NE tt 22 apr 4 Set SENET UTTE Upomo tison 2D Aspe 4 Senet BH ee ita tore MEFE A ULES aadd d 2 72 Na LA 52 32 OM he Ret D ijn pan sen RCEF EE UTET 155 22 SD S ULET aa 1 22 So ert a 8 eet T ve pe seei ta a orem os j x i 4 i 5 W Ae s S F wg Loca i ie A stees e ey l g toogle map So Spi 4 re a wa hnd code to the 3 o oso GPS tracker
8. TLT 2H Input the latitude and longitude that you receive from SMS and click on search button the Google earth will display the location map for you eg You receive the information from the tracker As follows Lat 22 50500 Long 114 01000 Speed 0 00KM H Direction 315 00 Date 2008 04 25 Time 16 39 45 BS 25ee0dff Fix A ID 353686009002030 STATE SMS Search the position on the Google map in relevant position input 22 50500 114 01000 Obtain the following picture Ge Oscgragtic wee po I Foe sO Q wns 6S P eons marose FO 3 Ires pE Gh itiar Or you can use local map software on PDA or car navigation device input the position date Note pay attention to change the position date format Leen m ancar LASTAL 9 gy maitre D gt zasai Reet perne vazu uia ae AAt s anmu ianryo annA Swa a wre ree irem ha SDENT 3 ce i Q au sadra Tuen ake unise KURE A a E ware 5 6a comet arer ee lt 1 eniker 1 T woii 1 szyk facet Aas Sacer ran ee 2E a En Peete 2 Cut off electricity and oil function 1 Open the cut off electricity and oil function a Command format 900 user password b Confirm command format 901 user password c Directly Command 940 user Password Note 940 900 910 the unit will implement this command at once after receive this command Description Due to the command with a certain d
9. successfully it will send the confirmation messages GEO FENCE OFF to the sender Note 1 Radius of the fence can not exceed the definition of its domain the value of the decimal part for zero must input zero fill For example R 1 it is important to enter into 1 0 2 If the calling state is off it will not call the user telephone number and only send messages to the present number 3 Degree and minute is divided into sexagesimal system converter that is 1d 60m Attention User can choose one of three way to set the Geo fence The unit will open this function after receive the command the last operation is available when close this function then open it again 14 Overspeed Alarm Function Format 122 Password X Eg 122 0000 250 Note X is mean reference value and the unit is mail hours KM H the area is 0 999 when the unit receive this command and confirm the password is correct Then implement this command X 250 is mean that when the speed of the car is Above 250KM H the unit will send a message to the threes users the format is like 1 1 and the state is OVER SPEED At this time if the speed of the car is lower as 250KM H then the unit will send a message to the send which the state is SAFE SPEED When you set the X 0 and at this time the unit will close this function when you set the X40 17 open this function and then send a message to the sender which is SET RATE LIMIT X 15 Upl
10. the area is 500M 21 Updata on the Air 1 Formate Password Eg 0000 Note when TLT 2H receive this command and confirm the password is correct the unit will restart and enter FTP Server to download procedure automatically after succesful the unit will restart again and it s ok 2 Formate Password FTP Address User Name Password Eg 0000 igarin gicp net auto 123 Note when TLT 2H receive this command and confirm the password is correct the unit will restart and enter FTP Server to download procedure automatically after succesful the unit will restart again and it s ok Attention the area of FTP Address is 5 35 and also can use domain and made is for characters numbers the user name is for FTP the area is 30 20 the password is FTP S password the area is 3 200 33
11. the sender The content is SET SERVER IP AND PORT OK 3 Upload Data Settings Automatically There are two mode about Upload Data Automatically One is Car Moving Tracking Mode Another is Car Stop Tracking Mode Both of this two mode is change automatically due to the ACC State The ACC is open and it s Car Moving Tracking Mode The ACC is close and it s Car Stop Tracking Mode The two mode is different according the configuration GPS interval time and upload number of data so can display the detail Real Time Trail when the state is Car Moving Tracking Mode and upload the data sparseness when the state is Car Stop Tracking Mode so can save the SIM Card Fee and also can keep the tracing effect When the Upload Data Setting is change the unit will send the data from the memory automatically and then follow the mode 3 1 Car Moving Tracking Mode Format 805 user password sampling interval T the number of upload data each time N eg 805 0000 1 O 1 Explanation The time T unit of the sampling is second 10 seconds at least 59999 seconds at most The number of upload data each time is N at least is 1 at most is 50 When TLT 2H receive the command and confirm the password is correct then TLT 2H will send a feedback message to the sender what is SET GPS SAMPLING TIME AND QUANTITY OK also will implement this command then the unit will get the GPRMC data and save in the memory and send the GPRMC Data to the serv
12. unit is open or close until the unit receive the new command 10 Three steps to send the GPS Position of unit to Platform 1 Set up the access point name of GPRS 1 Formatl 803 user password A PN eg 80340000 CMNET Format2 803 user password APN APN user name APN password Explanation1 Different GSM GPRS service associations provide different APN please according to local service providers to provide the APN to choose format 1 or 2 to use set Explanation2 When TLT 2H tracker receives the instruction and confirms the user password correctly updates the access point name to the new access point name After the success it will send the confirmation messages to the sender If sent the format 1 the content is SET GPRS APN OK 20 if it is format 2 the content is SET GPRS ACCOUNT OK Note APN is CMNET after factory set or reset APN is characters composed of 3 to 35 letters numbers dots underscore _ and connectors APN user name and user password are respectively characters composed of from 3 to 20 the numbers and letters 2 Set up the TCP IP server and IP s address and port number Format 804 user password fixed IP address port eg 804 0000 222 125 12 32 80 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly updates the IP address and port number preserved in the module After the success it will send the confirmation messages to
13. 000 Calling ON format 151 user password 4 figures eg 1510000 Explanation When TLT 2H tracker receives the instruction to close calling and confirms the user password correctly close the calling function including the SOS alarm when across the fence after successfully sent the confirm information SET VOICE CALL OFF to the sender When TLT 2H receives instruction to open calling and confirm the user password correctly open the calling function including the SOS alarm when across the fence after successfully sent the confirm information SET VOICE CALL ON to the sender 9 Upload The Call Explanation One of 3 telephone numbers stored in advance calls in hangs up after ringing 2 5 times Dispose as 5 6 the state item automatically updates STATE CALL 10 Upload The Emergency Case Explanation When press the SOS key more than 3 seconds it will do like 3 2 10 instruction the information state item automatically updates STATE SOS At the same time it will call the first preset user telephone number If it is unsuccessful closed or unable to connect or no response starts calling the second and the third in turn 26 Note If the calling state is off it will not call the user telephone number and only send messages to the server 11 Alarm When Cut Off Power Function 1 Open command o 011 user password eg 0110000 2 Close command 010 user password eg 0100000 Description When the TLT 2H rece
14. DIUS OK to the sender After configuration of the alarm for moving is complete if TLT 2H checking the ACC State is changed which from ACC ON to ACC OFF after three minutes the TLT 2H will take the current position for the coordiration point the unit will open the defence use the zzz z whether the GPS Data is Available or Valid when the ACC is OFF if TLT 2H checking the car over the defence in the SMS Mode the TLT 2H will send a message to the pre saved numbers what the state is STATE ACC OS the unit will send the current position to the server the state is ACC OS and call the pre saved numers the 150 151 comamnd will affect the unit that whether call the pre saved numbers if you reset the unit the unit will only send message and don t call numbers once the car coming the defence the unit will send current position information to the server or send message and call the pre saved numbers and the state is ACC RS Once TLT 2H checking the ACC state is close from Open to Close the Alarm for Moving will 32 close automatically when the ACC state is open from Close to open the Alarm for Moving will open automatically When TLT 2H receive 009 Command and confirm the password is correct the Alarm for Moving is closed automatically whatever ACC State is open or close unless send 008 command again after you set 009 command the utni will send MOVE DEFENGCE OFF to the sender Attention the Alarm for Moving of default is open and
15. User Manual TLT 2H GPS GSM Motorcycle Tracker 19 Introduction The TLT 2H GPS GSM Tracker is a Vehicle Positioning Device what based on GPS and GSM GPRS technology It s can transmit the Longitude and Latitude coordinates to your Mobile Phone by SMS And you can find the detail location of this unit on the Google Map or other Map Software Also The tracker can upload the positioning data to the server through GPRS So The user can look for Real Time Location Tracking Historical Tracking through the Internet The GPS and GSM Antenna is internal of this unit So it s very easy to installation And It s can use for Car Truck Motorcycle Bicycle etc Before you use this unit please spend some time to read the User Manual to know the operation way 2 Features 1 Support GSM 850 900 1800 1900 MHz Works worldwide 2 High sensitivity JRC low power GPS chipset 3 Excellent for fixing the position even at a weak signal status work well even in areas with limited sky view like urban canyons 4 Fast Signal Acquisition 5 Support single location and continuous tracking 6 Support alarm have 3 preset phone number 7 Support check location and real time and historical trajectory by SMS or Internet 8 SOS button send out exact location for immediate rescue action 9 Support cut off electricity and oil function and recovery command 10 High reliability circuit design in line with the automotive electronics industry standards
16. age POWER ON OK to the user Attention this function is certain risk it s will happen traffic in the freeway if you send this command so please consider again and again 16 Overspeed Alarm Function Format 122 Password X Eg 122 0000 250 Note X is mean reference value and the unit is mail hours KM H the area is 0 999 when the unit receive this command and confirm the password is correct Then implement this command X 250 is mean that when the speed of the car is Above 250KM H the unit will send a message to the threes users the format is like 4 1 6 and the state is OVER SPEED At this time if the speed of the car is lower as 250KM H then the unit will send a message to the send which the state is SAFE SPEED When you set the X 0 and at this time the unit will close this function when you set the X40 30 open this function and then send a message to the sender which is SET RATE LIMIT X 17 Upload the history data Record the history data If you want to use this function in SMS Mode you need to change the mode in GPRS and set the IP APN the detail way you can see the manual 1 configuration Format 807 user password X Note X is frequency the area is 0 999 the unit is second When the unit receive this command and confirm the password is right And set the history frequency is X When the X 0 that s close the function If X 30 that s mean that the unit will save the data every 30se
17. arious parts are as follows Edddmm mmmm is longitude information with units of degrees and minutes and the ddd expresses degree mm mmmm expresses minute Accuracy for4 after the decimal point the following zero cannot bypass Ndd mmmm is latitude information with units of degrees and minutes and the dd expresses degree mm mmmm expresses minute Accuracy for 4 after the decimal point the following zero cannot bypass Rzzz z is radius for the domain 999 9 0 1 unit for KM When the tracker receives this instruction judges to be authorized users and confirms the user password correctly it will send the confirmation messages SET GEO FENCE OK to the sender Format2 004 user password E Wddd dddddN Sdd dddddRzzz z eg 0040000E114 10004N22 55705R999 9 Explanation E east longitude W west longitude N north latitude S south latitude In this example uses E and N please according to the actual geographical position choose corresponding coordinate form to set In the demonstration meanings of various parts are as follows Eddd ddddd is longitude information with units of degrees and the ddd ddddd expresses degree Accuracy for 5 after the decimal point the following zero cannot bypass Ndd ddddd is latitude information with units of degrees and the ddd ddddd expresses degree Accuracy for 5 after the decimal point the following zero cannot bypass Rzzz z is radius for the domain 999 9 0 1 unit for KM When the
18. by real time and also want to check the History Record the users can choose GPRS Mode SMS Work Modep Format 700 user password 4 figures eg 7000000 Explanation When TLT 2H tracker receives the SMS and confirms the user password correctly it switches to the SMS application mode After the success it will send the confirmation messages SET MODE OK CURRENT MODE SMS P2P to the sender GPRS Work Modep Format 710 user password 4 figures eg 7100000 Explanation When TLT 2H tracker receives the SMS and confirms the user password correctly it switches to the GPRS application mode After the success it will send the confirmation messages SET MODE OK CURRENT MODE GPRS to the sender Generally Application of SMS Mode 1 1 Single localization request instruction Format 666 user password 4 figures eg 6660000 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly reads the GPS information No matter whether effective the information with the replying base station which is the set of the original software will be sent to the sender Data format Lat Latitude Direction Latitude Value Accuracy for 5 after the decimal point Long Longitude Direction Longitude Value Accuracy for 5 after the decimal point Speed Speed KM H Accuracy for 2 after the decimal point Direction Direction Accuracy for 2 after the decimal point Date Date YY YY MM
19. egree of risk so needs to do a more confirmation operation When the user need to cut off electricity and oil using a mobile phone to send format a command the device will return to Confirm Power OFF after it receives the order and confirm the user password correct If it receives the user sending format b command in ten minutes and confirms password correct white wire will output low level in order to control the outside relay to cut off oil and electricity After completion send confirmation message POWER OFF OK to the user 2 Cut off electricity and oil function to recovery command a Recovery command 902 user password b Confirm the recovery command 903 user password 11 Description When the device receives the cut off electricity and oil function to recovery command by the preset user numbers and confirms the password correct will send the confirm information Confirm Power ON to the sender and then prepares to receive the confirm command If within 10 minutes the device receives the users confirm command white wire will output high level in order to control the outside relay to recovery oil and electricity After completion send confirmation message POWER ON OK to the user c Recovery Command instant 941 user Password Note 941 902 903 the unit will implement this command at once after receive this command Attention this function is certain risk it s will happen traffic in the freeway if you send th
20. er if the data can t send it to the server by other excuse like GSM Signal or Bad Internet the data will save it automatically and when the internet is ok the unit will send the data again and the state is AUTO when users set the numberof data is 0 the unti will close this function and the unit will send message to the sender what is GPRS TIMER STOP 3 2 Car Stop Tracking Mode Format 809 user password X Y Explanation The time X unit of the sampling is second 10 seconds at least 59999 seconds at 21 most The number of upload data each time is Y at least is 1 at most is 50 Sampling interval T and the number of upload data each time N product should meet greater than equal 60 that is T N gt 60 When TLT 2H receive the command and confirm the password is correct then TLT 2H will send a feedback message to the sender what is GPRS REPORT SAMPLING 2 OK also will implement this command then the unit will get the GPRMC data and save in the memory and send the GPRMC Data to the server if the data can t send it to the server by other excuse like GSM Signal or Bad Internet the data will save it automatically and when the internet is ok the unit will send the data again and the state is AUTOLOW when users set the numberof data is 0 the unti will close this function and the unit will send message to the sender what is GPRS SAMPLING 2 STOP Attention 1 this function is not effect by open or close the unit until the unit receive
21. if the command is ok then send SET SAMPLEING OK to the unit Attention 1 the memory of every data is 100B the unit can save about 5000PCS Data 2 when the data is above 3000PCS Data the new data will recovery the old data automatically 3 If the Move Sensor is open already and the car is always stop the History Record will close automatically until the unit is wake Upload the history data A upload the history data of 24h Format 808 user password 24 When the unit receive this command and confirm the password is correct then send START UPLOAD ALL HISTORY RECORD and then send all of the data to the server The format is like 1 1 state is STORAGE Read all of the history data Format 808 user password When the unit receive this command and confirm the password is correct then send START UPLOAD ALL HISTORY RECORD and then send all of the data to the server The format is like 1 1 state is STORAGE 18 Low Voltage Warning When the TLT 2H s working voltage lower than the configuration the unit will read the GPS information whether or not effective immediately the unit will send the format as 4 1 6 location information to the three stored numbers the information state item automatically updates STATE LP Send a total of three times each time one minute interval 19 ACC detect charge function 1 For Charge Description TLT 2H check the state of ACC of the power through the ACC Cable so the ACC ON
22. ime call the first user telephone number If it is unsuccessful closed or unable to connect or no response makes vibration and starts calling the second and the third in turn When the TLT 2H re enters the fenced area it will immediately send location information format 3 1 5 to the three preset numbers The information state item prompts STATE RS At the same time 27 call the first user telephone number If it is unsuccessful closed or unable to connect or no response makes vibration and starts calling the second and the third in turn 1 Set the scope of the fence According to the input formats different of coordinates user can choose the format as follows instructions to operate Format1 003 user password E Wdddmm mmmmN Sdd mmmmRzzz z eg 003xxxxE11406 0024N2233 4230R1 Explanation E east longitude W west longitude N north latitude S south latitude In this example uses E and N please according to the actual geographical position choose corresponding coordinate form to set In the demonstration meanings of various parts are as follows Edddmm mmmm is longitude information with units of degrees and minutes and the ddd expresses degree mm mmmm expresses minute Accuracy for4 after the decimal point the following zero cannot bypass Ndd mmmm is latitude information with units of degrees and minutes and the dd expresses degree mm mmmm expresses minute Accuracy for 4 after the decimal point the following zero ca
23. is command so please consider again and again The Advanced Application and Configuration of SMS Mode 3 Set up the user password instruction Format 777 new password 4 figures old password 4 figures eg 77712340000 Explanation When TLT 2H tracker receives the SMS and confirm the user password correctly changes the new user password to the old password After set successfully it will send the confirmation messages SET USER PASSWORD OK to the sender 4 GPS state setting instruction GPS will enable on the on off adaptive three work states by send text messages command GPS state is open after factory settings or reset 5 Open the GPS instruction Format 222 user password 4 figures eg 2220000 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly opens the GPS power After the success it will send the confirmation messages GPS ON OK to the sender 6 Close GPS instruction Format 333 user password 4 figures eg 3330000 Explanation When TLI 2H tracker receives the instruction and confirms the user password correctly close the GPS After the success it will send the confirmation messages GPS OFF OK to the sender 7 Adaptive GPS instruction Power saving Function Format 100 user password 4 figures eg 1000000 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly it will close the GPS immedia
24. ive the armament command from the preset number and verifies the user password correct after success it will respond to confirm the information DEFENCE ON into the armament state after 10 seconds When the main external power supply was illegally cut off the TLT 2H will automatically send the current location information format as 4 1 6 to the 3 preset numbers STATE items for DEF At the same time call the first user telephone number If it is unsuccessful closed or unable to connect or no response starts calling the second and the third in turn When the TLT 2H receives the disarmament command from the preset number and verifies the user password correct after success it will respond to confirm the information DEFENCE OFF repeal disarmament TLT 2H is no longer monitor the illegal cutting external power supply case Note 1 After leave factory or reset it is the disarmament state It does not effect by boot until receives the command or reset 2 If the calling state is off it will not call the user telephone number and only send messages to the preset number 12 Hectronic Geo Fence Function Electronic fence takes the set coordinates as the center the set radius parameters to determine the scope of the fence When open this feature once the TLT 2H beyond the scope of the set fence it will send location information as to 3 1 5 to the 3 preset numbers The information state item automatically updates STATE OS At the same t
25. long interval time please contact us so we can design this for you 13 9 Calling switch instruction Calling OFF format 150 user password 4 figures eg 1500000 Calling ON format 151 user password 4 figures eg 1510000 Explanation When TLT 2H tracker receives the instruction to close calling and confirms the user password correctly close the calling function including the SOS alarm when across the fence and alarm when cut off power after successfully sent the confirm information SET VOICE CALL OFF to the sender When TLT 2H receives instruction to open calling and confirm the user password correctly open the calling function including the SOS alarm when across the fence after successfully sent the confirm information SET VOICE CALL ON to the sender 10 Telephone localization function Explanation One of 3 telephone numbers stored in advance calls in and hangs up after ringing 2 5 times then the TLT 2H will send the location information to this number such as 4 1 6 to this number the information state item automatically updates STATE CALL But other incoming numbers will automatically hang up 11 Seeking help initiatively When press the key more than 3 seconds it will send the location information such as 4 1 6 to 3 telephone numbers stored in advance the information state item automatically updates STATE SOS At the same time call the first user telephone number If it is unsuccessful closed o
26. ly send messages to the preset number 13 Electronic Fence Function Electronic fence takes the set coordinates as the center the set radius parameters to determine the scope of the fence When open this feature once the TLT 2H beyond the scope of the set fence it will send location information as to 4 1 6 to the 3 preset numbers The information state item automatically updates STATE OS At the same time call the first user telephone number If it is unsuccessful closed or unable to connect or no response makes vibration and starts calling the second and the third in turn When the TLT 2H re enters the fenced area it will immediately send location information format 4 1 6 to the three preset numbers The information state item prompts STATE RS At the same time call the first user telephone number If it is unsuccessful closed or unable to connect or no response makes vibration and starts calling the second and the third in turn 1 Set the scope of the fence According to the input formats different of coordinates user can choose the format as follows instructions to operate Format1 003 user password E Wdddmm mmmmN Sdd mmmmRzzz z eg 003xxxxE11406 0024N2233 4230R1 Explanation E east longitude W west longitude N north latitude S south latitude In this example uses E and N please according to the actual geographical position choose 15 corresponding coordinate form to set In the demonstration meanings of v
27. mand 210 user password After set successfully it will send the confirmation messages GEO FENCE OFF to the sender 15 Git Off Electricity And Oil Function a Command format 900 user password b Confirm command format 901 user password Description Due to the command with a certain degree of risk so needs to do a more confirmation operation When the user need to cut off electricity and oil using a mobile phone to send format a command the device will return to Confirm Power OFF after it receives the order and confirm the user password correct If it receives the user sending format b command in ten minutes and confirms password correct white purple wire will output low level in order to control the outside relay to cut off oil and electricity and back to confirm SMS POWER OFF OK 2 Cut off electricity and oil function to recovery command a Recovery command 902 user password b Confirm the recovery command 903 user password Description When the device receives the cut off electricity and oil function to recovery command by the preset user numbers and confirms the password correct will send the confirm information Confirm Power ON to the sender and then prepares to receive the confirm command If within 10 minutes the device receives the users confirm command white purple wire will output high level in order to control the outside relay to recover oil and electricity After completion send confirmation mess
28. nnot bypass Rzzz z is radius for the domain 999 9 0 1 unit for KM When the tracker receives this instruction judges to be authorized users and confirms the user password correctly it will send the confirmation messages SET GEO FENCE OK to the sender Format2 004 user password E Wddd dddddN Sdd dddddRzzz z eg 0040000E114 10004N22 55705R999 9 Explanation E east longitude W west longitude N north latitude S south latitude In this example uses E and N please according to the actual geographical position choose corresponding coordinate form to set In the demonstration meanings of various parts are as follows Eddd ddddd is longitude information with units of degrees and the ddd ddddd expresses degree Accuracy for 5 after the decimal point the following zero cannot bypass Ndd ddddd is latitude information with units of degrees and the ddd ddddd expresses degree Accuracy for 5 after the decimal point the following zero cannot bypass Rzzz z is radius for the domain 999 9 0 1 unit for KM 28 When the tracker receives this instruction judges to be authorized users and confirms the user password correctly it will send the confirmation messages SET GEO FENCE OK to the sender Format 3 005 User Password Rzzz z eg 0050000RO0 1 Note When this unit receive this command and confirm the password is right And read the Update gps data whether is available If ok take the lat log to the coordinati
29. oad the history data Record the history data If you want to use this function in SMS Mode you need to change the mode in GPRS and set the IP APN the detail way you can see the manual 1 configuration Format 807 user password X Note X is frequency the area is 0 999 the unit is second When the unit receive this command and confirm the password is right And set the history frequency is X When the X 0 that s close the function If X 30 that s mean that the unit will save the data every 30se if the command is ok then send SET SAMPLEING OK to the unit 1 the memory of every data is 100B 2 the memory of the unit for the history is 864KB For example if you set the X 30 it s about can save the data of three days If X 300 it s about can save the data of thirty days When the data is above 864KB the next new data will cover the oldest data 3 if the air sensor is open and also the unit is not move for a long time the history record will close and the unit will open once the unit is moving again 2 Upload the history data A upload the history data of 24h Format 808 user password 24 When the unit receive this command and confirm the password is correct then send START UPLOAD ALL HISTORY RECORD and then send all of the data to the server The format is like 1 1 the state is STORAGE 16 Low voltage warning When the TLT 2H s working voltage lower than the set to read the GPS information whether
30. on and the R for The Radius and also pen the Geofence at the same time If the configuration is ok The unit Will send set geo fence ok to the sender If the update GPS Data void the unit will give up and then red the next one if the unit can t receive the data above 50sec the unit will send A message to the sender which is ERROR GPS DATA TRY AGAIN LATER Note 1 Radius of the fence can not exceed the definition of its domain the value of the decimal part for zero must input zero fill For example R 1 it is important to enter into 1 0 2 If the calling state is off it will not call the user telephone number and only send messages to the present number 3 Degree and minute is divided into sexagesimal system converter that is 1d 60m 2 open the electronic fence 211 user password After set successfully it will send the confirmation messages GEO FENCE ON to the sender 3 close the electronic fence 210 user password After set successfully it will send the confirmation messages GEO FENCE OFF to the sender Attention User can choose one of three way to set the Geo fence The unit will open this function after receive the command the last operation is available when close this function then open it again 13 Qen the Electronic Fence Command 211 user password After set successfully it will send the confirmation messages GEO FENCE ON to the sender 14 Close the Electronic Fence 29 Com
31. or not effective immediately send the format as 4 1 6 location information to the three stored numbers the information state item automatically updates STATE LP Send a total of three times each time one minute interval 17 ACC detect charge function 1 For Charge Description TLT 2H check the state of ACC of the power through the ACC Cable so the ACC ON when the car is moving and the power of the car will recharge to the unit and the ACC Off when the car is parking and the power of the car will not recharge to the unit 2 The On Off Command for ACC State Open Command of ACC State 091 Password Eg 0910000 Close Command of ACC State 090 Password Eg 0900000 Note when TLT 2H receive the 091 command and confirm the password is correct TLT 2H will 18 send a message to the sender what the content is ACC STATE PROMPT ON when ACC is ON OFF the TLT 2H will send the current position to the pre saved numbers whether the GPS Data is avaible or valid and the state will display AUTO START AUTO STOP be the ACC State when TLT 2H receive the 090 command and confirm the password is correct TLT 2H will send a message to the sender what the content is ACC STATE PROMPT OFF when ACC is ON OFF the TLT 2H will not send any message whatever the unit is GPRS Or SMS Mode Attention the default is ON and once the configuration is ok whatever the unit is ON OFF the unit will not change until receve the next command or reset
32. r unable to connect or no response starts calling the second and the third in turn Note If the Calling State function is off it will not call the user telephone number and only send messages to the present number 12 Alarm when cut off power function 1 Open command o 011 user password eg 0110000 2 Close command 010 user password eg 0100000 Description When the TLT 2H receive the armament command from the preset number and verifies the user password correct after success it will respond to confirm the information 14 DEFENCE ON into the armament state after 10 seconds When the main external power supply was illegally cut off the TLT 2H will automatically send the current location information format as 4 1 6 to the 3 preset numbers STATE items for DEF At the same time call the first user telephone number If it is unsuccessful closed or unable to connect or no response starts calling the second and the third in turn When the TLT 2H receives the disarmament command from the preset number and verifies the user password correct after success it will respond to confirm the information DEFENCE OFF repeal disarmament TLT 2H is no longer monitor the illegal cutting external power supply case Note 1 After leave factory or reset it is the disarmament state It does not effect by boot until receives the command or reset 2 If the calling state is off it will not call the user telephone number and on
33. sages to the sender The content is CHANGE USERNAME OK 6 Change The Service Password Format 802 user password new service password old service password eg 802 0000 1111 0000 Explanation When TLI 2H tracker receives the instruction confirms the user password and old service password correctly changes the service password to the new service password After the success it will send the confirmation messages to the sender The content is CHANGE PASSWORD OK 7 Upload The Location Instruction At Once Format 806 user password eg 806 0000 Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly sends the confirmation messages to the sender The content is START GPRS UPLOAD At the same time send the data from the memory block to server 25 Upload format IMEI user name service password condition data quantity the base station s information GPRMC the base station s information GPRMC HH eg 123456789000001 TLT 2H 0000 SMS 3 25ee0dff GPRMC 083945 180 A 2233 4249 N 11406 0046 E 0 00 315 00 251207 A 6E 25ee0dff GPRMC 083950 180 A 2233 4249 N 11406 0046 E 0 00 315 00 251207 A 6E 25ee0dff GPRMC 083955 180 A 2233 4249 N 11406 0046 E 0 00 315 00 251207 A 6E Attention Immediately upload data format for the state SMS 8 Calling switch Instruction Calling OFF format 150 user password 4 figures eg 1500
34. tely and send the confirmation messages VIBRATION SENSOR ON OK to the sender The tracker built in vibration sensor once monitors the track movement for change to open the GPS If in 5 minutes with not monitors the track changed in the movement to close GPS Note If a long time on the highway or the flat road the GPS may be in sleeping and will not be awakened Users can send 222 user passwords to re open the GPS 8 Send the positional information in fixed time instruction Format 4 xx user password 4 figures eg 4010000 Explanation x indicates one figure from 0 to 9 while xx lt 60 its unit is minute while xx gt 60 its numerical value is xx minus 60 and unit is hour in other words 61 is 1 hour 62 is 2 hours followed by analogy When TLT 2H tracker receives the instruction and confirms the user password correctly it establishes the current time for initial timing time xx is the gap time and sends the confirmation SMS to the sender s mobile phone TIMER START REPEAT INTERVAL lt X gt MINUTES Then start to time and send the format as 1 1 setting information when it arrives the gap time the information state item automatically updates STATE TIMER When xx 00 cancels the positional information in fixed time instruction and sends the confirmation SMS to the sender s mobile phone TIMER STOP Attention the interval time can t above 2hours of this version at the moment if you need
35. the new command 2 The bland area only can save 300PCS Data the new data will recovery the old data if above 300PCS Data 3 Upload the data is limited by Move Sensor if the Move Sensor is open and the unit will stop send data in this state please see the detail specification of Move Sensor After you complete the three steps then you can track your car in the platform The Advanced Application and Configuration of GPRS Mode 1 Change the telephone number in advance instructions Format new numbers with 4 20 figures user password 4 figures location number 1 3 eg 13900000000 0000 1 Explanation You can store 3 telephone numbers at most in advance When TLT 2H tracker receives the instruction and confirms the user password correctly substitutes the new number for the existing number After success it will send the confirmation messages SET USER NUMBER 1 3 OK to the sender 2 Change the user password of TLT 2H Format 777 new password 4 figures old password 4 figures eg 77712340000 Explanation When TLT 2H tracker receives the SMS and confirm the user password correctly 22 changes the new user password to the old password After set successfully it will send the confirmation messages SET USER PASSWORD OK to the sender 3 GPS State Configuration instruction GPS will enable on the on off adaptive three work states by send text messages command GPS state is open after factory settings or reset
36. tion No matter whether effective the information with the replying base station which is the set of the original software will be sent to the sender Data format Lat Latitude Direction Latitude Value Accuracy for 5 after the decimal point Long Longitude Direction Longitude Value Accuracy for 5 after the decimal point Speed Speed KM H Accuracy for 2 after the decimal point Direction Direction Accuracy for 2 after the decimal point Date Date YY YY MM DD Time Time HH MM SS GMT BS Base Station information Fix Location state A V ID IMEI STATE Message state Effective data format Lat 22 50500 Long 114 01000 Speed 0 00KM H Direction 315 00 Date 2008 04 25 Time 16 39 45 BS 25ee0dff Fix A ID 353686009002030 STATE SMS Invalid data format Lat 22 50500 Long 114 01000 Speed 0 00KM H Direction 315 00 Date 2008 04 25 24 Time 16 39 45 BS 25ee0dff Fix V ID 353686009002030 STATE SMS BS 27971054 ID 353686009002030 STATE SMS Note If in the cold start and GPS no position it will return to the void of information eg ERROR GPS GPRMC FRAME DATA 5 Change The GPRS User Name Format 80 1 user password new user name egl 801 0000 username Explanation When TLT 2H tracker receives the instruction and confirms the user password correctly changes the user name to the new user name After the success it will send the confirmation mes
37. tracker receives this instruction judges to be authorized users and confirms the user password correctly it will send the confirmation messages SET GEO FENCE OK to the sender Note 1 Radius of the fence can not exceed the definition of its domain the value of the decimal part for zero must input zero fill For example R 1 it is important to enter into 1 0 2 If the calling state is off it will not call the user telephone number and only send messages to the present number 3 Degree and minute is divided into sexagesimal system converter that is 1d 60m Format 3 005 User Password Rzzz z eg 0050000R0 1 Note When this unit receive this command and confirm the password is right And read the Update gps data whether is available If ok take the lat log to the coordination and the R for The Radius and also pen the Geofence at the same time If the configuration is ok The unit Will send set geo fence ok to the sender If the update GPS Data void the unit will give up and then red the next one if the unit can t receive the data above 50sec the unit will send A message to the sender which is ERROR GPS DATA TRY AGAIN LATER After set ok the unit will come back the original state 2 open the electronic fence 211 user password After set successfully it will send the confirmation messages GEO FENCE ON to the sender 3 close the electronic fence 210 user password ERROR GPS DATA TRY AGAIN LATER After set
38. wire is right if errors installation led to the equipment damage At Own Risk the company is not responsible for it 70 Appl i cati on After you see the brief introduction of this unit now please see the detail operation of this unit Car battery anodel2V Car ACC power supply Car battery cathode 12V SOS bution Control oil and supply 87 87a 85 Relay 86 Car oil and Car oil and supply 12V supply 12V GPS GSM CHARGE oulput input First Step be the host of the unit onl y the pre saved numer can recei ve the alarmnessage fromthe unit but any nunber can send conmand to the unit to change the configuration of teh unit Qnmand as follow 6 1 Change the telephone number in advance instructions Format new numbers with 4 20 figures user password 4 figures location number 1 3 eg 13900000000 0000 1 Explanation You can store 3 telephone numbers at most in advance When TLT 2H tracker receives the instruction and confirms the user password correctly substitutes the new number for the existing number After success it will send the confirmation messages SET USER NUMBER 1 3 OK to the sender The Work Mode of TLT 2H TLT 2H have two work mode SMS and GPRS Mode If the users only need track the car by mobile phone and check the position latitude and longtitude in Google Map or control the oil and power by mobile phone SMS Mode is enough If the users want to track the car
Download Pdf Manuals
Related Search