Product Requirements Definition
Contents
1. Photo Setpoint High For switching When the light level is lower than this setting it will turn the lights ON when in ON OFF photo mode 1 Photo Setpoint Low For switching When the light level is higher than this setting it will inhibit the lights from turning ON or turn them off depending on the Photo Mode Douglas Lighting Controls Page 8 www DouglasLightingControls com 47 gt W Diversal gt Ph Set 1 Setpoint On Setpoint Off Photo Capture YesNo_ Ranges Ceiling Mount 0 800 Lux Wall Mount 0 800 Lux Wall Switch 0 800 Lux Photo Capture amp Temporary Dim These two functions are used to set the photo set points automatically Use the temporary 30 Sec dim to set the desired maintained light level Then send a Photo Capture to read the light level August 25 2015 Tech Support 1 877 873 2797 Olversa 2 8 Photo Setting Menu 2 4 gt W Diversa gt Ph Set 2 1 Photo Control 3 Switch Inhibit Disabled When enabled it will inhibit the Pole 2 Only switch from turning the light on if Both Poles there is sufficient ambient light detected Photo OFF setpoint 2 Photo Type Inhibit Only lf occupancy is detected AND there is a deficiency of natural light as determined by photo setpoint off the output is triggered on Once on the output remains on until a vacancy condition is determined by expiration of the vacancy timer An increase in natural light2. 873 2797
3. READ Clear Push RIGHT Off Push LEFT programmer will turn off automatically after one minute of no activity Write Push UP Read Push DOWN oe Ye 2 1 Sensor Information 41 gt B Diversal gt Info Model IR Lock 1 Model Number 4 Setting Read only Full Model number indicating This field indicates if the device is setup options Note lens type is not to use either the on board dip switch shown values or the IR settings 2 Hardware Version 5 IR Lock 3 Firmware Version i pa me Setting aor configuration is ignored and only the IR settings are used Douglas Lighting Controls Page 3 August 25 2015 www DouglasLightingControls com Tech Support 1 877 873 2797 Olversa 2 2 Occupancy Setting Menu 1 42 W Diversal gt Occ1 Mode Vacancy Time 3 Smart Sense 1 Occupancy Sensor Mode 3 The WO Diversa sensors can be setup to operate like a WV Diversa sensors by selecting between Occupancy or Vacancy modes 2 Vacancy Time Auto 30 Sec 1 minutes 5 minutes 10 minutes 20 minutes 30 minutes 40 minutes 60 minutes 90 minutes 120 minutes Smart Sense The timer keeps the ADI Voice on after vacancy timeout allowing the lights to be turned on with ADI Voice detection The selected time is used as the mid range for the adaptable 15 sec 30 sec 1 minute 1 30 minute 2 minutes 3 minutes 4 minute
4. Olversa WIR 3110 Infrared Setting Unit User Manual for Diversa Dual Technology Sensors Douglas Lighting Controls Page 1 July 20 2015 R1 0 www douglaslightingcontrols com Olversa 1 INTRODUCTION 1 1 GENERAL DESCRIPTION The WIR 3110 Infrared setting unit interfaces with the Diversa Occupancy sensors The Diversa Occupancy sensors use IR technology to allow touchless programming WIR 3110 Douglas Lighting Controls www DouglasLightingControls com infrared Receptor Liquid Crystal Display Panel LCD UP DOWN Buttons Toggles Up or Down through option fields LEFT RIGHT Buttons Selects the input component number to be programmed Lett for previous Right for next Scroll Wheel Scrolls through all options associated with a particular field Clockwise forward counter clockwise backward Center Select Button Push to turn unit on Sets and enters the Send Receive Menu Power Supply 2 AA standard alkaline Page 2 August 25 2015 Tech Support 1 877 873 2797 Olversa 2 FEATURES AND OPTIONS Menu Navigation A Menu Number Q Diversa gt Info B B Menu Title C Cursor Send Receive Send Receive range varies for each sensor form factor WOS type sensors are designed to have a very short range hold right up to the sensor lens WOR WOW type sensors are designed to have a significantly longer range A WiFi symbol will appear while the sensor is Reading or Writing Me WRITE VW
5. s 2 3 Occupancy Setting Menu 2 43 gt W Diversal gt Occ2 PIR Sense ADI Sense Med Walk Thru Indicator 1 Passive Infrared PIR Sensitivity 3 Walk Thru Mode Disabled When enabled this feature turns the Low lights off after 3 minutes if no Medium occupancy detection occurs after the High first 30 seconds after initial turn on 2 Accurate Detection Intelligence 4 Indicating LED ADI Voice Sensitivity If preferred this allows you to Disabled disable the motion and ADI Voice Low indicating LEDs Medium High Douglas Lighting Controls Page 4 www DouglasLightingControls com August 25 2015 Tech Support 1 877 873 2797 Olversa 2 4 Feature Enabling Menu 44 gt W Diversa gt Feature Switch _Enabled_ Photo Enabled 0 10V Dim _ Enabled Photo Dim Enabled 1 Switching Feature 3 0 10V Dimming Enable or Disable on board lf equipped enable or disable the 0 switch 10V dimming output 2 Photo ON OFF Feature 4 Photo Controlled Dimming lf equipped enable or disable the photocell feature This feature enables disables lights if adequate natural light is present Douglas Lighting Controls Page 5 www DouglasLightingControls com If equipped allow the 0 10V dimming amp photo options enabling it s function will allow the 0 10V output to be controlled by the photocell or at the fixed dim level see menu 9 August 25 2015 Tech Support 1 877 873 2797 Olversa 2 5 Switch Set
6. ting Menu 1 Use this menu to configure dual pole sensors as multi level lighting sequencing sensors 45 gt HJ Diversal gt Sw 1 Seq Pri Rly Alt Disable Pos 1 Sequences 2 Pole 2 Alternating Primary 2 Pole When enabled the primary pole will alternate for even lamp wear every time occupancy is detected does not apply to override button Once configured using WIR 3110 with each press of the override button the Diversa sensor steps through the sequence as per table below 3 Disable Mode E The sensor can be disabled by oe oo Pes ay applying 24VAC from the source on es i Pole Cll a pele the Sensor Link wire This option is 11 Both poles on to determine what action Is to be performed 01 Primary pole on secondary pole OFF off 10 RPT Repeat As is The first level is activated by the occupancy signal or switch if it is set to vacancy Douglas Lighting Controls Page 6 August 25 2015 www DouglasLightingControls com Tech Support 1 877 873 2797 Olversa 2 6 Switch Setting Menu 2 Use this menu to configure override button functionality 46 gt BDiversa gt Sw 2 1 Pole 1 Ovrrde _ ON OFF Pole 2 Ovrrde _ON OFF 1 Pole 1 Override 2 Pole 2 Override ON OFF ON OFF ON Only ON Only OFF Only OFF Only Douglas Lighting Controis Pae August 25 2015 www DouglasLightingControls com Tech Support 1 877 873 2797 Olversa 2 7 Photo Setting Menu 1
7. will not force the lights off ON OFF Control lf occupancy is detected AND there is a deficiency of natural light as determined by a programmable set point the output is triggered on Once on the output remains on until a vacancy condition is determined by expiration of the vacancy timer An increase in natural light will allow the lights to turn off and as the ambient light level drops the lights will turn on automatically If Photo is disabled on Menu 4 the following features are not applicable Switch Inhibit Photo Type Douglas Lighting Controls Page 9 August 25 2015 www DouglasLightingControls com Tech Support 1 877 873 2797 Olversa 2 9 Dimming Setting Menu 4 gt PDiversa gt Dim Dim Max __ Dim Min UnOcc Fn Rly OFF Fixed Dim 1 Dimming Maximum Limit amp 3 Unoccupied Function Fixed Dimming Output Minimum Dim Only 2 Dimming Minimum Limit Relay OFF 2 10 Miscellaneous Setting Menu 42 gt Diversal gt Misc 1 Aux Mode G Test Mode 3 RESET 1 Auxiliary Contact Mode R option 3 Test Mode Indicate Occupancy When activated the sensor options Indicate Output Signal are temporarily changed for quick reaction times Timeout 5 sec a wee ae Smart Sense 5 sec and ADI Voice gS enabled This will drop out to normal PO Stns mode after 30 minutes Audio Settings None Douglas Lighting Controls Page 10 August 25 2015 www DouglasLightingControls com Tech Support 1 877
Download Pdf Manuals
Related Search