Butterfly Quad - Prolight Concepts
Contents
1. DOWN buttons to set the sound mode on or off Press the ENTER button to confirm the setting To adjust the sound sensitivity press the MENU button on the front of the unit to show 52n5 on the LED display Now press the ENTER button and use the UP and DOWN buttons to set the sound sensitivity O IOD Press the ENTER button to confirm the setting Value O 100 0 low sensitivity 100 high sensitivity To exit out of any of the above options press the MENU button www prolight co uk Butterfly Quad User Manual 8 EQUINOX DMX setup Setting the DMX address The DMX mode enables the use of a universal DMX controller Each fixture requires a start address from 1 512 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 105 and 106 Choose a start address so that the channels used do not overlap E g the next unit in the chain starts at 107 DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA2. OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA cable DMX cable requirements for DMX operation This fixture can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output see image below Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers Please quote CABL10 2m CABL11 5m CABL12 10m Also remember that DMX cable must be daisy chained and cannot be split www prolight co uk Butterfly Quad User Manual 9 EQUINOX DMX setup Notice Be sure to follow the dia
3. 000 255 Tilt 2 Movement 60 150 000 255 Master dimmer O 100 000 009 010 255 Strobe slow fast 147 156 Program 15 157 166 Program 16 000 255 Red 0 100 dimming 167 176 Program 17 000 255 Green 0 100 dimming 000 255 Blue 0 100 dimming 000 255 White 0 100 dimming CH9 Program speed slow fast Program 10 CH9 www prolight co uk Butterfly Quad User Manual 6 EQUINOX Operating instructions 36 channel mode aa atin inion LED 4 Green 0 100 dimming LED 4 Blue 0 100 dimming LED 4 White 0 100 dimming LED 5 Red 0 100 dimming LED 5 Green 0 100 dimming LED 5 Blue 0 100 dimming LED 5 White 0 100 dimming LED 6 Red 0 100 dimming LED 6 Green 0 100 dimming LED 1 White 0 100 aie CH9 LED 2 Red 0 100 dimming LED 2 Green 0 100 dimming LED 2 Blue 0 100 dimming LED 2 White 0 100 dimming LED 3 Red 0 100 dimming LED 3 Green 0 100 dimming LED 3 Blue 0 100 dimming LED 3 White 0 100 dimming LED 4 Red 0 100 dimming cmi cH cus che ar chs j9 LED 6 Blue 0 100 dimming LED 6 White 0 100 dimming LED 7 Red 0 100 dimming LED 7 Green 0 100 dimming LED 7 Blue 0 100 dimming LED 7 White 0 100 dimming LED 8 Red 0 100 dimming LED 8 Green 0 100 dimming LED 8 Blue 0 100 dimming LED 8 White 0 100 dimming Master slave mode To set the master unit press the MENU button on the
4. use the equipment indoors Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable e Make sure that the available mains supply voltage is between 100 240V AC 50 60Hz e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically If the equipment is dropped or damaged disconnect the mains power supply immediately and have a qualified engineer inspect the equipment before operating again OPERATING DETERMINATIONS If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not connect power or switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature If your product fails to function correctly stop use immediately Pack the unit securely preferably in the original packing material and return it to your Pro Light dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS This lighting fixture is for professional use only it is not designed for or suitable for household use The product must be installed by a qua
5. EQUINOX Butterfly Quad User Manual V2 0 BUTTERFLY QUAD Order code EQLED100 EQUINOX WARNING Safety advice FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CARE FULLY BEFORE YOUR INITIAL START UP e Before your initial start up please make sure that there is no damage caused during transportation e Should there be any damage consult your dealer and do not use the equipment e To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e Please note that damages caused by user modifications to this equipment are not subject to warranty CAUTION KEEP THIS EQUIPMENT AWAY FROM RAIN MOISTURE AND LIQUIDS CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the unit e Do not open the equipment and do not modify the unit e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only
6. front of the master unit to show 5L fd on the LED display Now press the ENTER button and use the UP and DOWN buttons to choose MASE Press the ENTER button to confirm the setting Then select your desired program Sound active DMX or one of the built in programs To set the other units in slave mode press the MENU button on the front of the unit to show SL Md on the LED display Now press the ENTER button and use the UP and DOWN buttons to choose either 5L I Slave 1 or SL Slave 2 Press the ENTER button to confirm the setting The unit will now run in sequence with the master unit To exit out of any of the above options press the MENU button Please ensure that all slave units are set to the same DMX channel mode as the master unit Show mode built in programs To access the show modes press the MENU button on the front of the unit to show SA id on the LED display Now press the ENTER button and use the UP and DOWN buttons to choose the show you require from 5h 5H24 Press the ENTER button to confirm the setting To exit out of any of the above options press the MENU button www prolight co uk Butterfly Quad User Manual 7 EQUINOX Sound active mode To access the sound active mode press the MENU button on the front of the unit to show Solin on the LED display Now press the ENTER button and use the UP and
7. grams below when making your own cables Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR e ee eni XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground Q Pin 2 Negative 3Hot 3Hot Pin 3 Postive Special note Line termination When longer runs of cable are used Termination reduces signal transmission you may need to use a terminator on problems and interference it is always the last unit to avoid erratic behaviour advisable to connect a DMX terminal _ resistance 120 Ohm 1 4 W between pin 2 Using a cable terminator will decrease DMX and pin 3 DMX of the last fixture the possibilities of erratic behaviour 3 pin Order ref CABL9O 5 pin Order ref CABL89 S pin XLR DMX connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The diagram below details the correct cable conversion F B A E 5 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 pin XLR socket Pin 1 GND sc
8. lified technician in accordance with local territory regulations The safety of the installation is the responsibility of the installer The fixture presents risks of severe injury or death due to fire hazards electric shock and falls Warning Risk Group 2 LED product according to EN 62471 Do not view the light output with optical instruments or any device that may concentrate the beam WARRANTY One year from date of purchase If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns and electric shocks etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and or property www prolight co uk Butterfly Quad User Manual 2 EQUINOX Product overview amp technical specifications Butterfly Quad The Butterfly Quad is a dynamic multi beam effect featuring two sweeping LED bars each loaded with four individually controllable narrow beams Dispensing eight intense and sharp long throw beams the butterfly cuts through the air with ease The four button menu system allows control of master slave functions and the fixture can be also be operated in sound active and DMX modes e 8x 12W quad colour LEDs e Beam angle 4 5 e Pixel mapping capabilities e DMX channels 10 or 36 selectable e Auto sound active a
9. mode Jel fF LT i Sound sensitivity 0a Beer Blackout mode lalo el Jel fF Into lefs sell Tilt 1 inversion alo SEEL Tilt 2 inversion lalo Auto test LED display on LED display off Normal Inversion Fixture hours Firmware version Reset Butterfly Quad User Manual EQUINOX Operating instructions DMX mode Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independently To access the DMX address mode press the MENU button on the front of the unit to show Addr on the LED display Now press the ENTER button and use the UP and DOWN buttons to set the required DMX address Press the ENTER button to confirm the setting To exit out of any of the above options press the MENU button To access the DMX channel mode press the MENU button on the front of the unit to show ChA on the LED display Now press the ENTER button and use the UP and DOWN buttons to choose one of the 1 10 or 36 DMX channel modes Press the ENTER button to confirm the setting To exit out of any of the above options press the MENU button 1 channel mode cH1 008 128 129 255 10 channel mode Channel vatue Function 000 255 Tilt 1 Movement 60 150
10. nd master slave modes plus built in programs e 0 100 dimming and variable strobe e Tilt 180 e Quick release omega clamp included e 4 push button menu with LED display e IEC power input output e 3 Pin XLR input output Specifications Power consumption 100W Power supply 100 240V 50 60Hz Fuse F5A 250V Dimensions 165 x 400 x 220mm Weight 4 75kg Order code EQLED100 400mm 165mm WWOSEC www prolight co uk Butterfly Quad User Manual 3 EQUINOX 01 Function buttons 02 LED display 03 DMX input LED 04 Power LED 05 Sound LED www prolight co uk ZHO9 0S AOYT 0OT z a m fj S N 2 lt 06 Master LED 07 Fuse F5A 250V 08 IEC power input 09 IEC power output 10 3 Pin XLR DMX input Technical specifications DMX IN EQUINOX www prolight co uk DMX OUT 11 3 Pin XLR DMX output 12 Microphone 13 Earth point In the box 1 x fixture 1 x omega clamp 1 x power cable amp 1x user manual Butterfly Quad User Manual 4 EQUINOX www prolight co uk Ald a Ch Inja 51 Sih n a Slolvln 5 2Ins el nla Lu l tlela al l5 P pana Gaia e lels e F r S vlel e 5 e e Operating instructions KERN DMX address setting EEKE rich oleh Channel mode ale c f AIS Je Master mode Sl T Slave 1 Sl lal Slave 2 si al Show mode 0 24 ele Sound active
11. reen Pin 2 Signal Pin 3 Signal 5 pin XLR socket 3 pin XLR socket Pin 1 GND screen Pin 1 GND screen 0 9 Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 4 N C Pin 5 N C www prolight co uk Butterfly Quad User Manual 10 EQUINOX WEEE notice Correct Disposal of this Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries SS with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal tis www prolight co uk Butterfly Quad User Manual 11 EQUINOX www prolight co uk Butterfly Quad User Manual 12
Download Pdf Manuals
Related Search