POP Screen manual - Herma Projection Screen Technology
Contents
1. Q Fig 4a Fig 4 Side Grip Assembly Detail Al Detail B J 2 Secure wire 1 Secure to screen amp Fig 5 Side Grip Hanging Kit Assembly detail p Detail B D Detail A Bf z O 1 Attach universal grip to POP Screen See Fig 4a step 1 using 2mm allen key Supplied to tighten M4 grub screw 2 screw bosses to ceiling or wall See Fig 5 at the appropriate spacing depending on the size of the screen 3 Determine desired cable length and trim appropriately 4 Screw bottom boss to floor or wall See Detail B 5 Attach side grips to cable see Fig 4a step 2 and secure screen at the desired height installation instructions 5 jeoluUeUdO Installation Stabilising Bars t Remove plastic caps on both ends of top and bottom stabilising bars and remove clear plastic slide out screen grips see fig 6a 2 Attach plastic grips to top and bottom edges of POP Screen Make sure they are securely fastened Slide in plastic slider into top stabilising bar 3 Slide in screen with screen grip attached into channel of top and bottom Stabilising bars Replace 4 Secure Top Bosses See fig 2 Detail B to ceiling at the appropriate Spacing this depends on the size of the screen Mechanical Installation 5 Determine desired cable length and trim appropriately 6 Secure universal grip to top stablising bar see fig 6b Fig 6a Stabilising Bar Assembly D2. Repeat for three other edges m e SS Cc _ 4 Place screen into the frame so that it is securely 2 2 housed into the base of the frame 5 Close all four opened frame covers over the frame Fig 10 Securing the screen into the frame Place screen into the frame Open Frame cover 8 installation instructions Installation Framed Screens Hanging Attachments and Configuration 1 Determining appropriate spacing between hanging cables secure top grip kits to ceiling See page 4 of this instruction manual on details of how to do this 2 Secure frame tabs to frame with M6 bolt passing through larger hole of frame tab to slide nut inside of frame channel 3 Your framed POP screen should appear as that depicted in fig 12 Fig 11 Hanging detail for framed screens as S Universal D S a Ss Pe M6x12 secure frame tab Bolt Tt with grub screw oN A C krano tab TO ide nut Fig 12 Suspended Frame with Top Grip Suspension Kit Mounting Surface C See Fig 2 for Hanging kit installation installation instructions 9 Maintenance amp Troubleshoitting Maintenance and troubleshooting Cleaning instructions The screen surface on your Pop Screen is extremely delicate Special attention to these instructions should be followed when cleaning 1 A draftsman s style brush may be used to lightly whisk away any loose dirt or dust particles Do not use a sh
3. LP morgan POP Screen Notes and Cautions K TIP A tip indicates important information that helps you make better use of your screen gt WARNING A notice indicates potential damage to ceiling and tells you how to avoid the problem AN DANGER A caution indicates a potential for property damage personal injury or death Table of contents QI Important information Unpacking 3 i Installation Installation Top Grip Kit 4 Installation Side Grip Kit 5 Installation Stabilising Bars 6 Installation Framed Screens 7 4 Appendix 7 Maintenance amp Troubleshooting 10 Warranty Information 11 To the owner Congratulations on purchasing an LP Morgan Pop Screen A high quality rigid and low cost rear projection screen designed for visual merchandising applications Please take a moment to review this manual it will ensure you many years of trouble free service from your new POP Screen vertical mounting kit Information in this document is subject to change without notice 2002 2006 Herma Technologies All rights reserved Reproduction in any manner whatsoever without permission of Herma Technologies is strictly forbidden Trademarks used in this text Herma the Herma Logo LP Morgan and LP Morgan logo are registered trademarks of Herma Technologies Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their product Herma Technologies di
4. arp instrument to remove any particles Softly brush from the centre to the edges 2 Ihe screen may be cleaned with a mild solution of detergent and water and a sponge or soft lint free cloth Rub lightly to remove any stubborn marks then blot with a damp sponge to absorb excess water Use a clean sponge with clear water to wash off the detergent residue Dry the screen with a soft cloth towel so that the detergent does not have time to dry on the screen 3 NEVER attempt to use solvents chemicals or abrasive cleaners on the screen 4 We encourage you to keep your screen clean Avoid getting any foreign materials on it as cleaning may prove to be very difficult or even impossible scratches paint ink etc Never paint in the vicinity of the screen unless the screen surface is completely protected With reasonable care you may expect years of trouble free use of your LP Morgan POP screen 10 installation instructions Warranty Information Customers must fill out the online warranty form or the warranty card included with the product and post it back to Herma at the reply paid address shown on the back cover in order to qualify for the manufacturer s warranty www herma com au warranty The warranty covers defects in workmanship and materials provided this product has been installed in a normal environment and maintained according to the written instructions Herma warrants the product against loss of usefulness discolourati
5. etail Fig 6b Universal grip plastic slider attachment detail Remove plastic caps slide out screen grips X AO Tonen Fig 7 Assembled POP Screen with Stabilising Bars 4 4 4 Mounting Surface 4 4 4 4 6 installation instructions Installation Framed Screens Frame Assembly e Note If your screen has been pre assembled proceed to page 9 1 Place two slide nuts into channel of frame section which is intended to be directly above top edge of image 2 With frame pieces overturned place corner bracket on corner bracket plate and slide both into channel as far as possible as shown in fig 8 3 Tighten M6 grub screw using a flathead screwdriver 4 Repeat for three other corners placing brackets and frame pieces in position as shown in fig 9 5 Position and align frame sections tighten remaining grub screws to secure the frame Fig 8 ry lighten Frame Assembly detail SCorner bracket aN Q Place slide nuts i a a Corner bracket into this channel plate Fig 9 Bracket fixturing for frame assembly Postion amp Sn gras frame tion sections uo1 e e Su jeoiueyoaN installation instructions 7 Installation Framed Screens Screen Assembly 1 Place the frame face up on a flat and stable Surface 2 Open the frame covers located along the inner edge of the frame To do this reach inside of inner edge of frame and pull frame covers toward outer edge of frame 3
6. on or deterioration of optical quality within the warranty period as a result of manufacturing or material defects This warranty applies only within Australia CONDITIONS Herma will repair or replace with the least possible delay any defective equipment Any equipment replaced pursuant to the terms of this warranty shall be retained by Herma All costs related to installation and re installation of the Herma equipment covered by this warranty are not the responsibility of Herma Technologies Herma will not be responsible for any consequential damages during or following installation procedures The user is responsible for any freight costs relating to repair or replacement Equipment must be returned to Herma in suitable packing to prevent damage in transit Herma will not accept any responsibility for damage to the equipment caused by inadequate or unsuitable packing or for any damage howsoever caused whilst the goods are in transit Herma Technologies shall not be liable for any injury loss or damage direct or consequential arising out of the use of misuse of or inability to use the equipment This Warranty does not cover any equipment which has been subjected to misuse abuse neglect accidental or intentional damage improper voltage or any alteration which affects the reliability or performance of the equipment not attributable to faulty manufacture parts or labour and without limiting the generality of the foregoing shall no
7. sclaims interest in trademarks and trade names other than its own Apr 2006 Version 4 1 Unpacking the Pop Screen Supplied G Depending on the size of the screen chosen and the configuration 4 you have chosen to mount your screen you should have a selection 2 of the components shown below 2 x 2m Cable with top 2 x 2m Cable with side grip suspension kit grip suspension kit Stabilising bar kit for 45 49 60 amp 69 size screens only misc 2 x Stabilising Bars 10x Screen Grips 2x Sliding mounts 1x POP screen cut to size 2 xX M4x12 4 x End Caps Grub Screws Frame Kits NB frame is pre assembled if size is either 77 or 84 4 x Pieces of frame 4 x corner 4 x corner 8 x M6 grub extrusion bracket plate bracket screws M6 x 12 bolts 2 x frame tabs 2 X slide nuts installation instructions 3 yueyodu Installation Top Grip Kit Detail B Top Boss _ Fig 2 Top Grip Hanging Kit detail Assembly jo 2 OQ o E C o O 2 B 1 TE 1 Position universal grips to POP Screen See fig 1 and Detail A 2 A 1 to secure wire then A 2 to secure screen rine 3 Screw top boss to ceiling See Fig 2 Detail B Determine desired screen height trim wire to length Default wire length 2000mm Detail A 4 Secure wire at the top with grub screw B 1 db A 1 A 2 4 installation instructions Installation Side Grip Kit
8. t apply where the defect arose as the result of the following circumstances This Warranty does not cover any equipment where usage adaptation or installation including wiring of electrical connections are not in accordance with our written installation and operating instructions Warranty Period 2 years xipueddy R installation instructions 11 Your LP Morgan Retailer is able to provide information on your product If we can be of any further help please contact us mm l o morgan by HERMA Factory 4a 6 Albert Street Preston Vic 3072 Phone 61 3 9480 6233 Fax 61 3 9480 6533 Email info herma com au www lomorgan com au
Download Pdf Manuals
Related Search