Driver install manual
Contents
1. A3DRV User s Guide rev B 3 Software Installation When installing any system software be sure you have a current backup of your system while issues caused by device drivers are rare they can result in a system that is difficult to recover Always keep your Apple installation media for the system on hand in the unlikely event that you have to restore the system to an earlier state Instructions on manually removing the PCle device driver from a system can be obtained from your sales and support representative As this device driver supports disk controllers and will affect the volumes available to your system you SHOULD ensure that all internal disks are either powered off or unmounted by right clicking on their icons and selecting Eject lf you are upgrading your driver from a prior version you MUST ensure that all disks attached to the PCle device are powered off or ejected Otherwise the file systems on these disks may be corrupted by force unmounting that occurs during driver installation You will not need to reset the workstation once installation is complete the system will begin discovering disks that are attached and powered on and will automatically mount them to the desktop if able Step 1 Open the provided Disk Image usually named AstekFusion2Driver_xxx dmg Step 2 Run the installer package AstekFusion2 HBA Driver pkg Step 3 At the first and second screens click to continue See Illustration 12. A3DRV HBA A3DRV WARP SAS Host Bus Adapter Driver a wre User Manual Version B Document Number 90 000241 DOCUMENT 90 000241 VERSION B 10 02 2012 This document describes Astek s SAS Host Bus Adapter Card and Warp Card Driver and will remain the official reference source for all revisions releases of this product until rescinded by an update To receive product literature visit us at http www astekcorp com DISCLAIMER Astek Corporation reserves the right to make changes to any products herein at any time without notice Astek does not assume any responsibility or liability arising out of the application or use of any product described herein except as expressly agreed to in writing by Astek nor does the purchase or use of a product from Astek convey a license under any patent rights copyrights trademark rights or any other of the intellectual property rights of Astek or third parties Astek products are not intended for use in life support appliances devices or systems Use of any Astek product in such applications without written consent of the appropriate Astek officer is prohibited COPYRIGHT NOTICE Copyright 2011 2012 by Astek Corporation All rights reserved TRADEMARK ACKNOWLEDGMENT The Astek logo design is the trademark or registered trademark of Astek Corporation LSI LSI Logic and MPT are the trademarks or registered trademarks of LSI Inc All other brand and product names may be trademarks of t
3. SAS Domain 24 i SAS Address 44 33 22 11 06 00 00 00 Locations SCSI Target Identifier 9 Modems SCSI Peripheral Device Type O Volumes Manufacturer ATA WWAN iae Te MK8052G5 Software Applications SCSI Logical Unit 0 Developer Extensions Capacity 80 03 GE 80 026 361 856 bytes Farts SCSI Logical Unit Number 0 Model TOSHIBA MK amp 052G5X Frameworks rae raha Illustration 8 Unlicensed Driver Software 13 A3DRV User s Guide rev B For Astek Cards Determining the World Wide ID WWID Every Astek board product has a 16 character WWID This information is required for support in the event that you require assistance with a hardware issue Below is an example of WWID label affixed to an Astek PCle board The WWID will look like 50012BE000001234 wun Wi si a RE EE 1 ee i Illustration 9 LSI SAS 9200 16E SN Ent Illustration 10 LSI SLP 300 ws 25 lustration 11 LSI SAS9205 8e 14 A3DRV User s Guide rev B ji RD DSPEEE EE TTER ET EET ER Lid NS co on on wW 7L 000012 A Illustration 12 A3806 PCle Finding WWID 15 A3DRV User s Guide rev B For LSI Cards Determining the World Wide ID WWID Every LSI board product has a 16 character WWID This information is required for support in the event that you require assistance with a hardware issue Below are examples of WWID labels affixed to LSI PCle boards The WWID will be of the format
4. On the fourth screen you will be asked to select the disk on which to install the driver This must be the boot disk for the workstation with which you will be using the PCle card This disk should be selected by default and indicated with the green arrow Select the disk and click Continue Step 6 You will then be shown screen five with the size of the installation Click Install Make sure any attached disks are powered off or unmounted if you are upgrading Step 7 The final screen shows the summary and contact information for support See Illustration 2 Installation Complete A3DRV User s Guide rev B Introduction Read Me Destination Select Installation Type Installati Summ Install Astek Fusion MPT2 Drivers The installation was completed successfully The device driver is now installed you do not need to reboot the system Your disks should show up in the Finder window in a few seconds NOTE If you do not see any disks or you have multiple disks connected but only a single disk appears in Finder your are running in un licensed demo mode You must get a valid driver license file and have it installed on your system To do so please use the AstekActivationRequest tool in your Applications Utilities folder to activate your card s To remove the Astek driver delete the AstekFusion2Adapter kext extension from your System Library Extensions folder and the installed
5. 5OXXXXXX XXXXXXXX 16 A3DRV User s Guide rev B 5 Appendix Hardware Installation Follow these steps to install the PCle card Ground yourself before removing any electronic equipment or parts ESD can damage your system and or the PCle card Your warranty does not cover ESD induced damage to the host system or the PCl e card and is your responsibility lf you are unsure as to proper ESD procedures it is highly recommended to have the installation performed by a qualified technician Step 1 Remove the PCle Controller card from the ESD packaging and check that it is not damaged Step 2 Ensure that the workstation is powered down Step 3 Remove the side cover of the system See Illustration 13 Removing the workstation cover Illustration 13 Removing the workstation cover Step 4 Remove the Add In Card AIC retaining device See Illustration 14 Removing the AIC retaining device fingers and Illustration 15 Removing AIC retaining device screwdriver you may need a screw driver to remove the retaining screws if this has not been previously done 17 A3DRV User s Guide rev B Illustration 15 Removing AIC retaining device fingers device screwdriver Step 5 Remove the ESD shield from one of the unused PCle slots Step 6 Insert the PCle card into the open slot ensure the card is firmly seated by pushing against the bracket until the bracket is fully seated against the chassis See Illustrat
6. utilities AstekUpdateActivation AstekActivationRequest from the Applications Utilities directory For OEM branded products contact your OEM vendor For LSI branded standard PCle card products contact LSI for hardware support contact Astek for installation and driver licensing For Astek branded products licensing and all other support questions contact Astek Corporation at Illustration 2 Installation Complete Step 8 If you are using a non Astek provided HBA card you must activate your license If you have not already purchased a license you can do so by going to our A3DRV HBA Product page at our web storefront If you choose not to purchase a license you may use the Demo mode which limits the number of target disks media that can be accessed Your Product Authorization Key PAK will have the following format B AGOV LXAA W1DU BUAA AAPM Once you have received your PAK run the supplied helper utility AstekFusion2 HBA Activation Request app Which will bring up the dialog in figure Illustration 3 Enter Your Authorization Key Enter the PAK where prompted Please enter your authorization key fram Astek Cancel Illustration 3 Enter Your Authorization Key A3DRV User s Guide rev B Step 9 The utility will generate an email to Astek requesting the activation code this is separate from the authorization key See Illustration 4 Astek Activation Request eo Astek Fusion
7. 2 Activation Request a 4 Al fie 2 Send Chat Attach Address Fonts Colors Save As Draft Photo Browser Show Stationery To licensing astekcorp com Cc Subject Astek Fusion 2 Activation Request Assembly H3 25260 01D Tracer P170015109 WWID 50012be000001e80 Assembly Tracer WWID 500605b0034769b0 Authorization Key Provided X XXA X A RAR RAR ARM AC ACC Illustration 4 Astek Activation Request Step 10 If you provided a valid PAK license code you will receive a PAC within one business day Monday through Friday 8am to 5pm Mountain Time USA If you have previously activated your card serial number with your PAK you do not need to re issue the activation request simply use the PAC previously sent to you If you would like to change your license to a new PCI card you must contact your Astek Sales representative A3DRV User s Guide rev B Step 11 When you have received your Product Activation Code PAC open the AstekFusion2 HBA Update Activation app utility normally installed in Applications Utilities Step 12 As Prompted Ensure that all Drives are unmounted before proceeding See Illustration 5 Un mount Hard Drives Before proceeding please follow the steps below 1 You must safely unmount any media attached to the SAS controller by right clicking or control clicking on the disk and selecting Eject 2 Once the media has been un mounted disconnect th
8. First install screen A3DRV User s Guide rev B AOO Install Astek Fusion MPT2 Drivers Welcome to the Astek Fusion MPT2 Drivers Installer AstekFusion2 Driver for Apple Macintosh OS X Introduction This device driver supports the following Astek Host Bus Adapter Read Me products Destination Select A3806 PCIE 01 LSISAS2008 based 8 port Gen2 SAS HBA A3807 PCIE 01 LSISAS2308 based 8 port Gen2 SAS HBA A31606 PCIE 01 LSISAS2116 based 16 port Gen2 SAS HBA The driver also supports several standard LSI board products including LSISAS9200 8e LSISAS2008 based 8 port Gen2 SAS HBA LSISAS9205 8e LSISAS2308 based 8 port Gen2 SAS HBA LSISAS9201 16e LSISAS2116 based 16 port Gen2 SAS HBA In addition to HBA products this driver also supports cards from OEM partners and certain PCle SSD products with appropriate licensing If you have questions about supported cards versions required or need licensing please contact your channel and or OEM vendor first Astek does not offer free technical support for OEM products a Nate come SI ctandard rarde are cunnarted hit nat lictad here Go Back Continue D ebar eee Illustration 1 First install screen Step 4 On the third screen you will be asked to accept the license terms for the driver You must click Accept to install this device driver For additional information on the license terms see your sales and support representative Step 5
9. e cables or power down any external disks and enclosures 3 Proceed with this installation RC Cancel Rae Illustration 5 Un mount Hard Drives Step 13 Enter your PAC from Astek on the screen See Illustration 6 Activation Code Entry Screen Enter the Activation Code TE Fa 1 il Cancel Se CC Illustration 6 Activation Code Entry Screen 10 A3DRV User s Guide rev B Step 14 Done no need to reset the workstation The driver should be automatically reloaded If there is any conflict with the loaded kernel extensions you may see an error message from the Activation Utility in this case you will need to reboot your system 11 A3DRV User s Guide rev B 4 Troubleshooting Apple System Profiler You can verify correct installation by opening the Apple System Profiler available by clicking on the About this Mac selection under the Apple icon menu in the upper left hand corner of your screen then click the More Info button Under the PCI cards section you should see a card of type SAS Controller If the card does not appear here check to ensure that the card is properly seated in the PCI slot Mac Pro Copernicus 9 7 10 3 07 PM Contents Card Type Driver Installed Bus Slot F Hardware NVIDIA GeForce GT 120 display Yes PCI Slot 1 ATA pcil000 72 SAS Controller Yes PCI Slot 3 Audio Built In Bluetooth Diagnostics Disc Burning Ethernet Cards Fibre Channel FireWi
10. formation about the hardware products see Astek Corporation for the A3806 PCI and A3807 PCI card products LSI Corporation for the LSISAS SLP WLP BLP card products Features Full support for both 32 bit kernel mode 10 6 and 64 bit kernel mode 10 6 10 7 10 8 Supports Serial Attached SCSI controller cards including full support for SATA media In licensed mode the driver supports up to 255 target devices Supports direct attach and connection through SAS Bus Expanders With Lion OS X 10 7 and later supports Asymmetric Logical Unit Access ALUA Supports any number of PCle cards including mixing HBAs and PCle SSD cards A3DRV User s Guide rev B 2 Supported Platforms Software This driver offers support for the following operating systems Apple Macintosh OS X 10 6 10 8 X86 32 bit and 64 bit Hardware The driver software is Known to be compatible with the following controller cards Astek A3806 PCle A3807 PCle A31606 PCle LSI LSISAS9200 8e LSISAS2008 based 8 port Gen2 SAS HBA LSISAS9201 16e LSISAS2116 based 16 port Gen2 SAS HBA LSISAS9202 16e LSISAS2008 based 16 port Gen2 SAS HBA LSISAS9205 8e LSISAS2308 based 8 port Gen2 SAS HBA LSISAS9207 8e LSISAS2308 based 8 port Gen2 SAS HBA w PCle 3 0 LSISSS6200 300 LSI WarpDrive Gen2 SAS HBA LSI WLP4 200 PCle 2 0 SSD LSI WLP4 400 PCle 2 0 SSD LSI BLP4 400 PCle 2 0 SSD LSI BLP4 800 PCle 2 0 SSD LSI BLP4 1600 PCle 2 0 SSD
11. heir respective companies TECHNOLOGY LICENSES The hardware and or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license Revision Date Auth Pages Notes A 08 11 11 TAB All Initial Draft DTC B 10 02 12 TFV All Updated OS X versions supported updated list of supported hardware updated license activation entry process Table of Contents SEAIS i AEE PEE E E E E E EE E PE EEEE E EEE EE 5 OWA O a a E E E E A NN E E E a AE E 5 3 Software Installation sas cosivccecccsscccccnasevaceniecacconscvsienssussonniseacaoscveteuniaerduniacatavsuversonnsedsduaiaeasasuecesienasessoueieensas 6 RE A ba eosgectnsas eaeatea ras 12 Apple Systemi Protel miseros i T E A a EA a E E ee 12 For Astek Cards Determining the World Wide ID WWID ie 14 For LSI Cards Determining the World Wide ID WWID iii 16 5 Appendix Hardware CLEO eo 17 A3DRV User s Guide rev B 1 Introduction The Astek AS3DRV device driver supports a number of PCI Express PCle 6 Gigabit per second Gbps Serial Attached SCSI SAS Host Bus Adapters HBA from LSI Corp Astek and Astek s OEM partners The driver provides the necessary software for Apple Macintosh OS X 10 6 through 10 8 to communicate with the controller card and provides some system utilities to assist the operator in managing their SAS topology For in
12. ion 16 Ensure PCle card is fully seated against bracket Step 7 18 A3DRV User s Guide rev B Step 8 Re install the Add In Card retention device See Illustration 17 Reinstall AIC retaining device You should use a screwdriver for this if the installation is intended to be permanent to ensure it does not come loose if the workstation is moved Illustration 17 Reinstall AIC retaining device Step 9 Replace the side cover of the workstation Step 10 Connect the external disk array or JBOD using an iPASS cable in most cases supplied with your disk array See Illustration 18 Connect iPASS cable and Illustration 19 Properly seated iPASS cable 19 A3DRV User s Guide rev B Illustration 18 Connect iPASS cable gt gt Lit LEZ serere de LV Scores Illustration 19 Properly seated iPASS cable Step 11 Power up the workstation Proceed to software installation Section 3 20 A3DRV User s Guide rev B 6 Support For additional support contact your OEM sales representative If you are unable to contact the seller of your PCl e card you may contact Astek Corporation for additional information Email support astekcorp com Web http www astekcorp com By Phone 719 260 1625 21
13. re Graphics Displays Hardware RAID Memory PCI Cards Parallel SCSI Power Printers Soa SAS pcil000 72 pie Type SAS Controller USE Driver Installed Yes Network Bus PCI AirPort Slot Slot 3 Vendor ID Ox 1000 Firewall Device ID OxO0 2 Locations Subsystem Vendor ID Ox1000 Modems Subsystem ID Ox30b0 Volumes Revision ID Ox 0002 ay F Software Link Speed 5 0 GT s Applications Developer Extensions Fonts Frameworks Logs Managed Client Preference Panes Startup Items Sync Services Universal Access Illustration 7 Apple System Profiler Screen PCI Card 12 A3DRV User s Guide rev B In the SAS section select the desired SAS Domain example 24 If the card appears as unlicensed in the product field refer to steps 9 12 in the Software Installation section See Illustration 8 Unlicensed Driver Software 8 12 11 11 57 AM Hardware l TSAS Domain 24 ATA FSCS Target Device 9 Audio Built In SCSI Logical Unit Bluetooth TSAS Domain 25 Card Reader SCSI Target Device 36 Diagnostics SCSI Logical Unit Disc Burning Ethernet Cards Fibre Channel FireWire Graphics Displays Hardware RAID Memory PCI Cards Parallel SCSI Power Vendor Unknown OEM Astek Corp Printers Product S4S9200 8e Unlicensed CAS Revision H3 25260 01D gt Bus PLI Serial ATA Slot Slot 4 Thunderbolt Initiator Identifier 126 USE Speed 6 Gigabit Y Network AirPort SCSI Target Device Firewall
Download Pdf Manuals
Related Search