PCI-1752U User Manual
Contents
1. PCI 1752U Isolated Digital Output Card User Manual Copyright The documentation and the software included with this product are copy righted 2005 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this man ual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reli able However Advantech Co Ltd assumes no responsibility for its use nor for any infringements of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Part No 2003175200 Ist Edition Printed in Taiwan February 2006 PCI 1752 User Manual ii Product Warranty 2 years Advantech warrants to you the original purchaser that each of its prod ucts will be free from defects in materials and workmanship for two years from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accid2. Richtigkeit der in diesem Zusammenhang get tigten Aussagen ab Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage 1 To avoid electrical shock always disconnect the power from your PC chassis before you work on it Don t touch any components on the CPU card or other cards while the PC is on 2 Disconnect power before making any configuration changes The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components PCI 1752 User Manual vi Contents Introduction ccccccccccscscssscscscscscscscscscscseseee 2 Features Figure 1 1 Installation Flow Chart 4 Installation Guide Accessories nn Installation ss S Unpacking 32 5 8 enter 8 Driver Installation uen 9 Figure 2 1 Advantech Automation Software Setup 9 Hardware Installation eenen ene 10 Figure 2 2 Device name listed on Device Manager 11 Device Setup amp Configuration 12 Figure 2 3 Device Setting dialog box of PCI 1752 12 Device Testing nn Shee hee eit ee St ees eh ods Figure 2 4 Advantech Device Manager Figure 2 5 Digital Output in Device Test dialog box 14 Signal Connections esse LO I O Connector Pin Assignment annen ennen eene ennen Location of Jumpers and DIP switch Figure 3 1 1 0 Connector Pin Assignments Table 3 1 1 0 Connector Signa
3. D 16 M 5 Mm 10031 17 iD Pcomo m PCOMI 18 Pcomo MD Pcomt 19 Pcomo 0 20 8 D Pcomt 21 IGND IGND 22 IGND D IGND 23 IGND D IGND 24 D IGND IGND 25 CH_FRZ_IN D CH_FRZ COM PCI 1752 User Manual 38 CH_FRZ_COM Appendix D Connect with PCL 10250 CON2 IDO 48 IDO 49 IDO 50 IDO 51 IDO 52 IDO 53 IDO 54 IDO55 IDO 56 IDD 57 IDO 58 IDO59 IDO 60 IDO61 IDO62 IDO63 PCOMS PCOMS PCOMS PCOMS IGND IGND IGND ISND TB2 T T D D D D D D D D D D 26 27 28 29 30 31 32 33 34 35 36 37 38 39 gi S 5 amp 4 50 39 ID 32 ID 0 33 ID 0 34 IDO35 06 07 68 9 0 01 IDO 42 3 ID O 44 IDO 45 6 ID O 47 2 2 PCOM2 PCOM2 IGND IGND IGND IGND CH_FRZ_IN TB1 u u 0 0 0 u u 0 T T T T T T T T T T T T 2 D D pwn a KE e n i CON D us re ee a B NM OD 4 N 40 PCI 1752 User Manual
4. Table A 1 Isolated Digital Output Number of Output Channels PCI 1752 64 Optical Isolation 2500 Voc Throughput 10 kHz Supply Voltage 5 40 Vic Sink Current 200 mA max channel General Table A 2 General Specifications 1 0 Connector Type 100 pin SCSI II female Dimensions 175 mm x 100 mm 6 9 x 3 9 Power Consumption Typical 5V 230 mA Max 5V 500 mA Temperature Operation 0 60 C 32 140 F refer to IEC 68 2 1 2 Storage 20 70 C 4 158 F Relative Humidity 5 95 RH non condensing refer to IEC 68 2 3 Throughput rate depends on the computer hardware architecture and software environment The rates may vary due to programming language code efficiency CPU utilization and so on PCI 1752 User Manual 30 APPENDIX Block Diagram Appendix 8 Block Diagram Address Bus Control Logic Data Bus PLX J i PCI 9052 DOO IDO15 10016 ID031 PCI S Isolation SCSI BUS 1D032 D047 E 100 Pin mn Connector 10048 IDO63 CH_FRZ IN PCI 1752 User Manual 32 APPENDIX Register Structure and Format Appendix C Register Structure amp Format C 1 Overview The PCI 1752U USO is delivered with an easy to use 32 bit DLL driver for user programming under the Windows XP 2000 operating system We advise users to program the PCI 1752U USO using the 32 bit DLL driver
5. Advantech disclaims all responsibility for the accuracy of any statements contained herein Wichtige Sicherheishinweise 1 1 Bitte lesen sie Sich diese Hinweise sorgfaltig durch 2 Heben Sie diese Anleitung f r den sp teren Gebrauch auf 3 Vor jedem Reinigen ist das Ger t vom Stromnetz zu trennen Ver wenden Sie Keine Fl ssig oder Aerosolreiniger Am besten dient ein angefeuchtetes Tuch zur Reinigung 4 Die NetzanschluBsteckdose soll nahe dem Ger t angebracht und leicht zug nglich sein 5 Das Ger t ist vor Feuchtigkeit zu sch tzen 6 Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Verletzungen hervorrufen 7 Die Bel ftungs ffnungen dienen zur Luftzirkulation die das Ger t vor berhitzung sch tzt Sorgen Sie daf r daB diese ffnungen nicht abgedeckt werden 8 Beachten Sie beim AnschluB an das Stromnetz die AnschluBw erte 9 Verlegen Sie die NetzanschluBleitung so daB niemand dar ber fallen kann Es sollte auch nichts auf der Leitung abgestellt werden 10 Alle Hinweise und Warnungen die sich am Ger ten befinden sind zu beachten 11 Wird das Ger t ber einen l ngeren Zeitraum nicht benutzt sollten Sie es vom Stromnetz trennen Somit wird im Falle einer berspan nung eine Besch digung vermieden 12 Durch die L ftungs ffnungen d rfen niemals Gegenst nde oder Fl ssigkeiten in das Ger t gelangen Dies k nnte einen Brand bzw elektrischen Sch
6. all of the card s func tions without register level programming For users who prefer to imple ment their own bit level programming please refer to the information in this chapter 4 1 Board ID The PCI 1752 PCI 1752USO have a built in DIP switch SW1 which is used to define each card s board ID You can determine the board ID on the register as shown on Table 4 1 When there are multiple cards on the same chassis this board ID setting function is useful for identifying each card s device number through board ID We set the PCI 1752 PCI 1752USO board ID as 0 at the factory If you need to adjust it to other board ID set the SW1 by referring to the Table 4 2 Table 4 1 Board ID register Base Add decimal 3 2 1 0 Abbreviation ID3 ID2 ID1 IDO 100 the least significant bit LSB of Board ID 103 the most significant bit MSB of Board ID Table 4 2 Board ID setting Board ID dec Switch Position 3 2 1 0 0 l l l 1 ij 14 k 15 o o o O Off 1 On default There are two ways to make association of the device number with the corresponding board ID The first way is to check the content in 7 0 PCI 1752 User Manual 24 Device Installation Dialog Box as shown in Fig 4 1 The second way is to determine the board ID by its device number through DLL function DRV DeviceGetFeatures For detailed information please refer to software manua
7. and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures PCI 1752 User Manual iv e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FM The PCI 1752U PCI 1752USO have passed the FM certification According to the National Fire Protection Association work sites are classified into different classes divisions and groups based on hazard considerations PCI 1752U PCI 1752USO are compliant with the specifi cations of Class I Division 2 Groups A B C and D indoor hazards Technical Support and Assistance Step 1 Visit th
8. provided by Advantech to avoid the complexity of low level pro gramming by register The most important consideration in programming the PCI 1752U USO at the register level is to understand the function of the card s registers The information in the following sections is provided only for users who would like to do their own low level programming C 2 I O Port Address Map The PCI 1752U USO requires 32 consecutive addresses in the PC s I O space The address of each register is specified as an offset from the card s base address For example BASE 0 is the card s base address and BASE 7 is the base address plus seven bytes PCI 1752 User Manual 34 C 3 PCI 1752 Register Format PCI 1752 Register Format Base 15 14 13 12 111 10 9 8 7 16 15 4 3 2 11 0 Add 0 R Digital Output Group 0 Read Back DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 15 14 13 12 11 10 9 B 17 16 5 4 3 2 1 JO W Digital Output Group 1 DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 15 14 13 12 11 10 19 B 17 16 5 4 3 12 1 JO 2 R Digital Output Group 1 Read Back DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 W Digital Output Group 1 DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 4 R Digital Output Group 2 Read Back DO DO DO DO DO
9. 019 15 65 IDO21 16 66 10023 17 67 10025 18 68 IDO27 19 69 10029 20 70 81 21 71 PCOM1 22 72 PCOM1 23 73 GND 24 74 GND 25 75 CH FRZ COM 26 76 10033 27 77 10035 28 78 10037 29 79 10039 30 80 Don 31 at 10043 3 82 10045 33 83 10047 34 84 Pcom2 35 85 PCOM 36 86 GND 37 87 GND 38 88 IDO49 39 83 DOS 40 so 10053 41 91 10055 42 92 10057 43 93 10059 44 34 10061 45 95 10063 46 96 47 97 6083 48 98 IGND 49 99 IGND 50 100 CH FRZ COM A 0000 000 IDOD4 006 006 010 012 014 PCOMO PCOMO IGND IGND 6 18 08 10022 4 8 8 28 01 01 IGND IGND CH FRZIN 10032 10034 8 8 408 IDO42 4 8 PCOM2 PCOM2 IGND IGND 8 0 ID052 4 6 8 0 62 PCOM3 PCOM3 IGND IGND CH_FRZ_IN IDO00 IDO15 Isolated digital output of Group 0 IDO16 IDO31 Isolated digital output of Group 1 IDO32 IDO47 Isolated digital output of Group 2 IDO48 IDO63 Isolated digital output of Group 3 PCOMO External common input of Group 0 PCOM1 External common input of Group 1 PCOM2 External common input of Group 2 PCOMS External common input of Group 3 IGND Isolated ground CH_FRZ_IN Channel Freeze input pin CH_FRZ_COM Common pin for Channel Freeze input Figure 3 1 I O Connector Pin Assignments Chapter 3 17 Table 3 1 1 0 Connector Signal Descriptions Description Isolated digital output of group 0 Isolated digital output of
10. 52U PCI 1752USO card in any PCI slot on your com puter But it is suggested that you should refer to the computer user man ual or related documentations if you have any doubt Please follow the steps below to install the card on your system Step 1 Turn off your computer and unplug the power cord and cables TURN OFF your computer before installing or removing any com ponents on the computer Step 2 Remove the cover of your computer Step 3 Remove the slot cover on the back panel of your computer Step 4 Touch the metal part on the surface of your computer to neutralize the static electricity that might be on your body Step 5 Adjust DIP switch SW1 on board to set the card s board ID Step 6 Insert the PCI 1752U PCI 1752USO card into a PCI slot Hold the card only by its edges and carefully align it with the slot Insert the card firmly into place Use of excessive force must be avoided otherwise the card might be damaged Step 7 Fasten the bracket of the PCI card on the back panel rail of the computer with screws Step 8 Connect appropriate accessories 100 pin cable wiring termi nals etc if necessary to the PCI card PCI 1752 User Manual 10 Step 9 Replace the cover of your computer chassis Re connect the cables you removed in step 2 Step10 Plug in the power cord and turn on the computer Note In case you installed the card without installing the DLL driver first Windows XP 2000 will recognize your ca
11. 752U 1752USO also features a wide output voltage range from 5 to 40 Vic suitable for most industrial applications with 12 Vpc 24 Vpc output voltage In the mean time we are also ready to serve your special needs for specific input output voltage range Do not hesitate to ask us about tailoring our standard products to meet your specifications All these merits make PCI 1752U USO the best choice for industrial applications Board ID Setting The PCI 1752U USO has a built in DIP switch that helps define each card s ID when multiple cards have been installed on the same PC chas sis The board ID setting function is very useful when users build their system with multiple PCI 1752U USO cards With correct Board ID set tings you can easily identify and access each card during hardware con figuration and software programming Channel Freeze Function The PCI 1752U 1752USO provides Channel Freeze function which can be enabled either in dry contact or wet contact mode selectable by the on board jumper When the Channel Freeze function is enabled the last status of each digital output channel will be safely kept for emergency use Moreover you can enable this function through software as it is use ful in software simulation and testing program 3 Chapter 1 Install Driver from CD ROM then power off PC Install Hardware and power on PC Use driver utility to configure hardware Use test utility to test hardware Read exa
12. DO DO DO DO DO DO DO DO DO DO DO 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 W Digital Output Group 2 DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 6 R Digital Output Group 3 Read Back DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 W Digital Output Group 3 DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 8 R N A WIN A A R N A WIN A 10 R Board ID Register 0310 WIN A 12 R Channel Freeze Function Control Register CFS CF Wl Channel Freeze Function Status Register 35 Appendix C 36 PCI 1752 User Manual 0 APPENDIX ADAM 3951 Pin Assignments Appendix D ADAM 3951 Pin Assignments Connect with PCL 10250 CON1 TB1 TB2 1 10000 D 100 16 2 D 10017 3 0002 0 4 Dd 1000 D 10018 5 m 4 D 10020 e 0 10021 7 10022 8 MD 3 3 8 D 10024 10 98 DM 10025 11 MD 10026 12 001 M 7 13 10012 D 10028 14 M 10013 10029 15 10014
13. O card to provide high resistance to noise To achieve a better signal quality the signal wires are twisted in such a way as to form a twisted pair cable reducing crosstalk and noise from other sig nal sources 5 Chapter 1 Wiring Boards ADAM 3951 The ADAM 3951 is a 50 pin SCSI wiring terminal module with LED indicators for DIN rail mounting This terminal mod ule can be readily connected to the Advantech PC Lab cards and allow easy yet reliable access to individual pin connections for the PCI 1752U USO card PCI 1752 User Manual 6 CHAPTER Installation Sections include e Unpacking e Driver Installation Hardware Installation e Device Setup and Configuration e Device Testing Chapter 2 Installation This chapter gives users a package item checklist proper instructions about unpacking and step by step procedures for both driver and card installation 2 1 Unpacking After receiving your PCI 1752U PCI 1752USO package please inspect its contents first The package should contain the following items M PCI 1752U PCI 1752USO card M Companion CD ROM DLL driver included M User Manual The PCI 1752U PCI 1752USO card harbors certain electronic compo nents that are vulnerable to electrostatic discharge ESD ESD could easily damage the integrated circuits and certain components if preven tive measures are not carefully paid attention to Before removing the card from
14. anager On the Device Test dialog box users are free to test various functions of PCI 1752U PCI 1752USO on the Digital output tab Testing Digital Output Function Click the Digital Output tab to bring up the Digital Output test panel such as seen on the next page By pressing the buttons on each tab users can easily set each digital output channel as high or low for the corresponding port 13 Chapter 2 A Advantech Device Test 1 1752 BoardID 0 1 0 E800H Analoginput Analog output Digitalinput Y Digital output 77 ont nl oto Fr ja al ae MEAN M x T E T rd T o ENEN sl v Change device Exit Figure 2 5 Digital Output in Device Test dialog box Only after your card device is properly set up configured and tested can the device installation procedure be counted as complete After the device installation procedure is completed you can now safely proceed to the next chapter Signal Connections PCI 1752 User Manual 14 CHAPTER Signal Connections Sections include I O Connector Pin Assignment e Location of Jumpers and DIP switch e Isolated Digital Output Connections e Field Wiring Considerations Chapter 3 Signal Connections Maintaining sig
15. ctromagnetic sources such as power lines large electric motors circuit breakers or welding machines since they may cause strong electromagnetic interfer ence Keep the analog signal cables away from any video monitor since it can significantly affect a data acquisition system Ifthe cable travels through an area with significant electromagnetic interference you should adopt individually shielded twisted pair wires as the analog input cable This type of cable has its signal wires twisted together and shielded with a metal mesh The metal mesh should only be connected to one point at the signal source ground Avoid running the signal cables through any conduit that might have power lines in it If you have to place your signal cable parallel to a power line that has a high voltage or high current running through it try to keep a safe distance between them Or you should place the signal cable at a right angle to the power line to minimize the undesirable effect The signals transmitted on the cable will be directly affected by the quality of the cable In order to ensure better signal quality we recom mend that you use the PCL 10250 shielded cable 21 Chapter 3 22 PCI 1752 User Manual CHAPTER Operation Sections include Board ID e Channel Freeze Function Chapter 4 Operation This chapter describes the operation of the PCI 1752U PCI 1752USO The software driver provided allows users to access
16. e 3 2 Power on configuration after hot reset PCI 1752 JP1 Power on configuration after hot reset 1 Keep last status after hot reset 9 1 Load default configuration Default setting 0 19 Chapter 3 Isolated Outputs Each of isolated output channels comes equipped with a Darlington tran sistor Every 16 output channels share common collectors and integral suppression diodes for inductive loads Note If an external voltage 5 40 Vpc is applied to an isolated out put channel while it is being used as an output channel the current will flow from the external voltage source to the card Please take care that the current through each IDO pin not exceed 200 mA Figure 3 3 shows how to connect an external output load to the card s iso lated outputs External PCI 1752U sink type Figure 3 3 Isolated DO PCI 1752U sink type External Internal PCI 1752USO source type Figure 3 4 Isolated DO PCI 1752USO source type PCI 1752 User Manual 20 3 4 Field Wiring Considerations When you use the PCI 1752U PCI 1752USO to acquire data from out side noises in the environment might significantly affect the accuracy of your measurements if due cautions are not taken The following measures will be helpful to reduce possible interference running signal wires between signal sources and the PCI 1752U PCI 1752USO The signal cables must be kept away from strong ele
17. e Advantech web site at www advantech com support where you can find the latest information about the product Step 2 Contact your distributor sales representative or Advantech s cus tomer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version appli cation software etc A complete description of the problem The exact wording of any error messages Safety Instructions 1 Read these safety instructions carefully 2 Keep this User s Manual for later reference 3 Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for clean ing 4 For plug in equipment the power outlet socket must be located near the equipment and must be easily accessible 5 Keep this equipment away from humidity 6 Put this equipment on a reliable surface during installation Drop ping it or letting it fall may cause damage 7 The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS 8 Make sure the voltage of the power source is correct before con necting the equipment to the power outlet 9 Position the power cord so that people cannot step on it Do not place anything over the power cord 10 All cau
18. ent or improper instal lation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous test ing most of our customers never need to use our repair service If an Advantech product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your man ual product and any helpful information readily available 3 Ifyour product is diagnosed as defective obtain an RMA return merchandise authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for war ranty service 5 Write the RMA number visibly
19. group 1 Isolated digital output of group 2 Isolated digital output of group 3 Common pin for inductive loads of isolated output channels IDO00 ID015 Common pin for inductive loads of isolated output channels IDO16 1DO31 Common pin for inductive loads of isolated output channels IDO32 IDO47 Common pin for inductive loads of isolated output channels IDO48 IDO63 Isolated ground Channel Freeze function input pin Common pin for Channel Freeze function input Direction Output Output Output Output Input Input Input Input Input Input 18 Reference PCOMO PCOM1 PCOM2 PCOM3 CH_FRZ_COM Signal Name IDO lt 00 15 gt IDO lt 16 31 gt IDO lt 32 47 gt IDO lt 48 63 gt PCOMO PCOM1 PCOM2 PCOM3 IGND CH_FRZ_IN CH_FRZ_COM PCI 1752 User Manual 01 1 JP2 mm m Figure 3 2 Location of Jumpers and DIP switch 3 3 Isolated Digital Output Connections Power On Configuration Default configuration after power on and hardware reset is to set all the isolated output channels to open status the current of the load can t be sink so that users need not worry about damaging external devices during system startup or reset When the system is hot reset then the status of isolated digital output channels are selected by jumper JP1 Table 3 2 shows the configuration of jumper JP 1 Tabl
20. ital output card The Advantech PCI 1752U PCI 1752USO isolated digital output card is a powerful data acquisition card for both 3 3 5V PCI bus It features a unique circuit design and complete functions for data acquisition and control PCI 1752U PCI 1752USO provides 64 iso lated digital output channels The following sections of this chapter will provide further information about features of PCI 1752U PCI 1752USO a Quick Start for installation together with some brief information on software and accessories 1 1 Features The Advantech PCI 1752U PCI 1752USO DAS cards provide users with the most requested measurement and control functions as seen below PCI 1752 DAS card 64 isolated digital output channels High voltage isolation on output channels 2 500 Voc Wide output range 5 40 Voc High sink current for isolated output channels 200 mA max ch Board ID Output status read back Digital output value retained after hot system reset Channel Freeze function Output status read back D The PCI 1752U PCI 1752USO DAS cards offer the following main fea tures Robust Protection The PCI 1752U PCI 1752USO features a robust isolation protection for applications in industrial lab and machinery automation The PCI 1752U USO can durably withstand a voltage up to 2 500 Vic prevent ing your host system from any incidental harms PCI 1752 User Manual 2 Wide Output Range The PCI 1
21. l Descriptions Figure 3 2 Location of Jumpers and DIP switch 19 Isolated Digital Output Connections 19 Table 3 2 Power on configuration after hot reset 19 Figure 3 3 Isolated DO PCI 1752U sink type 20 Figure 3 4 Isolated DO PCI 1752USO source type 20 Field Wiring Considerations 21 COEF ATOM u a 24 Table 4 1 Board ID register Table 4 2 Board ID setting Figure 4 1 Device ff and board ID on dialog box 25 Channel Freeze Function 25 Table 4 3 JP2 Channel Freeze function input mode 26 Figure 4 2 Wiring in wet dry contact input mode 26 Table 4 4 Channel Freeze function register 26 Table 4 5 Channel Freeze function bit value 27 Table A l Isolated Digital Output Table A 2 General Specifications Block Diagramme 32 Register Structure amp Format ee 34 ix Table of Contents Chapter 1 1 1 1 2 123 Chapter 2 2 1 2 2 2 3 2 4 2 3 Chapter 3 3 1 32 3 3 3 4 Chapter 4 4 1 4 2 Appendix A Appendix B Appendix C Cal Overview ren nt ren sue 34 C2 1 0 Port Address Map nonnen enn ennenneene eneen 34 C 3 PCI 1752 Register Format aaneen ene eneen 35 Appendix ADAM 3951 Pin 581811111611118 38 PCI 1752 User Manual x Chapter 1 Introduction Thank you for buying the Advantech PCI 1752U PCI 1752USO isolated dig
22. l on CD ROM IO Device Installation Installed Devices Cancel 0 65004 001 C1 1754 No 4 1 0 6700H Setup Device No Board ID Remove Add gt gt Test 30 About Figure 4 1 Device and board ID on dialog box 4 2 Channel Freeze Function The PCI 1752U PCI 1752USO provide the channel freeze function for isolated digital output channels When Channel Freeze function is enabled all ports on the card will be locked so that the data transmitted from the host PC to the card won t be transferred to the DO ports Once the Channel Freeze function is enabled each port status is immediately frozen into its last valid value before the Channel Freeze Since the value transmitted from the host PC to the card is also stored in the buffers on PC thus when user calls the DRV_DioGet CurrentDOByte function to read back the DO channel value this function will determine that If Channel Freeze function is disabled it will return the DO value on the port If Channel Freeze function is enabled it will return the value from the buffers on host PC The PCI 1752U provides a digital input channel CH_FRZ_IN to enable channel freeze function and PCI 1752USO provides one input channel The channel freeze function acts when the pin CH_FRZ_IN is activated Moreover you can setup the input mode of channel freeze function input 25 Chapter 4 channel CH FRZ IN as dry contact input mode or wet co
23. lag ausl sen 13 ffnen Sie niemals das Ger t Das Ger t darf aus Gr nden der ele ktrischen Sicherheit nur von authorisiertem Servicepersonal ge ff net werden 14 Wenn folgende Situationen auftreten ist das Ger t vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu berpr fen a Netzkabel oder Netzstecker sind besch digt vii b Fl ssigkeit ist in das Ger t eingedrungen c Das Ger t war Feuchtigkeit ausgesetzt d Wenn das Ger t nicht der Bedienungsanleitung entsprechend funk tioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erz ielen e Das Ger t ist gefallen und oder das Geh use ist besch digt f Wenn das Ger t deutliche Anzeichen eines Defektes aufweist 15 VOSICHT Explisionsgefahr bei unsachgemaben Austausch der Batterie Ersatz nur durch densellben order einem vom Hersteller empfohlene mahnlichen Typ Entsorgung gebrauchter Batterien navh Angaben des Herstellers 16 ACHTUNG Es besteht die Explosionsgefahr falls die Batterie auf nicht fach m nnische Weise gewechselt wird Verfangen Sie die Batterie nur gleicher oder entsprechender Type wie vom Hersteller empfohlen Entsorgen Sie Batterien nach Anweisung des Herstell ers Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr gt 70dB A oder weiger Haftungsausschluss Die Bedienungsanleitungen wurden entsprechend der IEC 704 1 erstellt Advantech lehnt jegliche Verantwortung f r die
24. mples amp driver manual Start to write your own application Figure 1 1 Installation Flow Chart PCI 1752 User Manual 4 Reset Protection When the system has undergone a hot reset i e without turning off the system power the PCI 1752 1756 can either retain outputs values of each channel or return to its default configuration as open status depend ing on its on board jumper setting This function protects the system from wrong operations during unexpected system resets 1 2 Installation Guide Before you install your PCI 1752U USO card please make sure you have the following necessary components PCI 1752U PCI 1752USO Isolated digital output card PCI 1752U PCI 1752USO User s Manual Driver softwareAdvantech DLL drivers included in CD ROM Wiring cable PCL 10250 Wiring boardADAM 3951 ComputerPC or workstation with PCI bus slot Win XP 2000 After you get the necessary components and maybe some accessories for enhanced operation for your DAS card you can then begin the Installa tion procedures Figure 1 1 on the next page provides a concise flow chart to give users a broad picture of the software and hardware installa tion procedures u Q u Q Q u 1 3 Accessories Advantech offers a complete set of accessory products to support the PCI 1752U USO cards These accessories include Wiring Cable The PCL 10250 shielded cable is specially designed 10250 for PCI 1752U US
25. nal connections is one of the most important factors in ensuring that your application system is sending and receiving data cor rectly A good signal connection can avoid unnecessary and costly dam age to your PC and other hardware devices This chapter provides useful information about how to connect input and output signals to the PCI 1752U PCI 1752USO via the I O connector 3 1 I O Connector Pin Assignment The I O connector on the PCI 1752U PCI 1752USO is a 100 pin connec tor that enable you to connect to accessories with the PCL 10250 shielded cable Figure 3 1 shows the pin assignments for the 100 pin I O connector on the PCI 1752U PCI 1752USO and Table 3 1 shows its I O connector signal description Note The PCL 10250 shielded cable is especially designed for the PCI 1752U USO to reduce noise in the analog signal lines Please refer to Section 1 3 Accessories 3 2 Location of Jumpers and DIP switch Figure 3 1 shows the names and locations of jumpers and DIP switch on the PCI 1752U and PCI 1752USO There are two jumpers JP1 and JP2 on the PCI 1752U PCI 1752USO Please refer to Section 3 3 Isolated Digital Output Connection and Sec tion 4 2 Channel Freeze Function for more information about JP1 and JP2 configurations PCI 1752 User Manual 16 u 1 51 D001 2 52 03 3 53 1DO05 4 54 7 5 65 IDO09 6 56 1 7 57 10013 8 58 10015 9 59 Pcomo 10 60 0 11 61 IGND 12 62 IGND 13 63 10017 14 64 10
26. ntact input mode selected by on board jumper JP2 as shown in Table 4 8 The wir ing in wet contact and dry contact input mode are shown in Figure 4 2 Otherwise you also can enable the function through software by writing 1 to CFC Channel Freeze Function Control bit on channel freeze function register as shown in Table 4 9 and Table 4 10 It s useful in soft ware simulation and testing program The CFS Channel Freeze Function Status bit shows the status of Chan nel Freeze function A value of 1 for the CFS bit indicates an active Channel Freeze Function whereas a value of 0 indicates a non active Channel Freeze Function Table 4 3 JP2 Channel Freeze function input mode 1 Channel Freeze function dry contact input mode 1 Channel Freeze function wet contact input mode Extremal Internal Extremal Internal 10 50V a For Wet Contact b For Dry Contact Figure 4 2 Wiring in wet dry contact input mode Table 4 4 Channel Freeze function register Base Add decimal 3 2 1 0 Abbreviation CH_FRZ_ON CH_FRZ_EN PCI 1752 User Manual 26 Table 4 5 Channel Freeze function bit value Chapter 4 Channel Freeze function control Disable Enable Channel Freeze function flag OFF ON 27 CH_FRZ_EN 0 1 CH_FRZ_ON 0 1 28 PCI 1752 User Manual APPENDIX Specifications Appendix Specifications Isolated Digital Output
27. on the outside of the package and ship it prepaid to your dealer iii Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Advantech Please contact your local supplier for ordering information CE This product has passed the CE test for environmental specifications Test conditions for passing included the equipment being operated within an industrial enclosure In order to protect the product from being damaged by ESD Electrostatic Discharge and EMI leakage we strongly recom mend the use of CE compliant industrial enclosure products FCC Class A Note This equipment has been tested and found to comply with the limits for a Class digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Opera tion of this equipment in a residential area is likely to cause harmful inter ference in which case the user will be required to correct the interference at his own expense FCC Class B Note This equipment has been tested
28. r system during driver setup complete device installation procedure should include device setup configuration and testing The following sections will guide you through the Setup Configuration and Testing of your device 2 4 Device Setup amp Configuration On the Device Setting dialog box Fig 2 3 you can enable disable the Channel Freeze function of PCI 1752U PCI 1752USO PCI 1752 Device Setting Channel Freeze function Base Address 800 C Enable fe Disable Cancel About Figure 2 3 Device Setting dialog box of PCI 1752 If you want to test the card device further go right to the next section on the Device Testing 2 5 Device Testing Following through the Setup and Configuration procedures to the last step described in the previous section you can now proceed to test the device by clicking the Test Button on the O Device Manager dialog box Fig 2 4 PCI 1752 User Manual 12 Advantech Device Manager Your ePlatform Partner IND bine me Device Manager r Installed Devices Le SI My Computer Setup 001 lt PCI 1752 BoardID 0 0 E800H gt 5 Supported Devices Advantech DEMO Board Advantech PCI 1680 lt lt Advantech PCI 1710 L HG HGL lt lt Advantech PCI 1711 Advantech PCI 1711L PCI 1731 Advantech PCI 1712 lt lt Advantech PCI 1713 lt lt Advantech PCI 1714 UL lt lt Advantech PCI 1718U Figure 2 4 Advantech Device M
29. rd as an unknown device after reboot and will prompt you to provide necessary driver You should ignore the prompting messages just click the Cancel but ton and set up the driver according to the steps described in Section 2 2 Driver Installation After the PCI 1752U PCI 1752USO card is installed you can verify whether it is properly installed on your system in the Device Manager 1 Access the Device Manager through Control Panel System Device Manager 2 The device name of the PCI 1752U PCI 1752USO should be listed on the Device Manager tab on the System Property Page 3 Device Manager BAX File Action View Help gt amp g E 047 la 4 Advantech DA amp C I O cards E9 Advantech PCI1752 Device Disk drives Display adapters gt DVD CD ROM drives Floppy disk controllers Human Interface Devices 3 IDE ATAJATAPI controllers amp IEEE 1394 Bus host controllers Infrared devices Keyboards 3 Mice and other pointing devices Be Modems 2 Monitors EB Network adapters PCMCIA adapters 0 Ports COM amp LPT MR Processors 7 amp SCSI and RAID controllers Sound video and game controllers v HAA A AA Figure 2 2 Device name listed on Device Manager 11 Chapter 2 After your card is properly installed on your system you can now config ure your device using the Device Installation Program that has itself already been installed on you
30. s The 32 bit DLL driver Setup program for the PCI 1752U PCI 1752USO card is included on the companion CD ROM that is shipped with your DAS card package Please follow the steps below to install the driver software Step 1 Insert the companion CD ROM into your CD ROM drive Step 2 The Setup program will be launched automatically if you have the autoplay function enabled on your system When the Setup Program is launched you ll see the following Setup Screen eAutomation AD ANTECH PANS On Pavee 3 E PAEA CONTINUE Figure 2 1 Advantech Automation Software Setup 9 Chapter 2 Note If the autoplay function is not enabled on your computer use Windows Explorer or Windows Run command to execute AUTORUN EXE on the companion CD ROM Step 3 Click Continue and select the Installation option Step 4 Select the specific device and then just follow the installation instructions step by step to complete your device driver installation and setup For further information on driver related issues an online version of the Device Drivers Manual is available by accessing the following path Start Programs Advantech Automation Advantech Device Man ager Device Driver s Manual 2 3 Hardware Installation Note Make sure you have installed the driver first before you install the card please refer to Section 2 2 Driver Installation After the DLL driver installation is completed you can now go on to install the PCI 17
31. the antistatic plastic bag you should take following precautions to ward off possible ESD damage Touch the metal part of your computer chassis with your hand to dis charge static electricity accumulated on your body Or one can also use a grounding strap Touch the antistatic bag to a metal part of your computer chassis before opening the bag Take hold ofthe card only by the metal bracket when removing it out of the bag After taking out the card first you should e Inspect the card for any possible signs of external damage loose or damaged components etc If the card is visibly damaged please notify our service department or our local sales representative immedi ately Avoid installing a damaged card into your system Also pay extra caution to the following aspects to ensure proper instal lation Avoid physical contact with materials that could hold static elec tricity such as plastic vinyl and Styrofoam PCI 1752 User Manual 8 Whenever you handle the card grasp it only by its edges DO NOT TOUCH the exposed metal pins of the connector or the electronic compo nents Note Keep the antistatic bag for future use You might need the origi nal bag to store the card if you have to remove the card from PC or transport it elsewhere 2 2 Driver Installation We recommend you to install the driver before you install the PCI 1752U PCI 1752USO card into your system since this will guarantee a smooth installation proces
32. tions and warnings on the equipment should be noted 11 Ifthe equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage 12 Never pour any liquid into an opening This may cause fire or elec trical shock 13 Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel 14 Ifone of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture d The equipment does not work well or you cannot get it to work according to the user s manual e The equipment has been dropped and damaged f The equipment has obvious signs of breakage 15 DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS COULD DAM AGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT 16 CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORD ING TO THE MANUFACTURER S INSTRUCTIONS The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70 dB A PCI 1752 User Manual vi DISCLAIMER This set of instructions is given according to IEC 704 1
Download Pdf Manuals
Related Search